72711000_-_7110_na
Installation and Operating Instructions
Morsø 7110
For use in North America
MORSØ JERNSTØBERI A/S . DK-7900 NYKØBING MORS
E-Mail: stoves@morsoe.com · Website: www.morsoe.com
Congratulations on the purchase of your new
Morsø stove!
Morsø, which is the largest supplier for the Danish market, has manufactured stoves of the highest
quality since1853. By following the instructions overleaf, we are sure that you will enjoy the use and the
benefits of your stove for many years to come.
Contents
1.0
Installation of your Morsø stove
1.1
Checking loose parts in the stove
1.2
The chimney / flue system
1.3
Flue connection
1.4
Connection to the existing chimney
1.5
Positioning the stove
1.6
Mobile home installation
Page no.
4
5
6
6
8
9
2.0Operation
2.1
Before you start firing
2.2
Lighting & loading intervals
11
11
12
3.0Maintenance
3.1
Exterior maintenance
3.2
Internal maintenance
3.3
Cleaning the stove & the flue
3.4
Leaving the stove for extended periods
3.5
Parts diagram
3.6
Parts list
16
16
16
18
19
20
21
Read this entire manual before you install and use your new room heater. If this room
heater is not properly installed, a house fire may result. To reduce the risk of fire, follow
the installation instructions. Failure to follow instructions may result in property damage, bodily injury, or even death.
Contact local building officials about restrictions and installation inspectionrequirements
in your area.
Save these instructions
2
Optional Accessories
A wide range of accessories (such as handling gloves, fireside tools, glass cleaner and heatproof paint) are available for use with your Morsø stove. They help with day-to-day running
and maintenance. Contact your Morsø dealer for more information.
The Morsø 7110 meets the U.S. Environmental Protection Agency’s emission limits for wood
heaters sold on or after July 1, 1990.
The Morsø 7110 have been tested by OMNI-Test Laboratories, Inc. The test standards are
ANSI/UL-1482 for the United States and ULC S627 for Canada.
The stove is listed for burning wood only. Do not burn other fuels.
Under specific test conditions this heater has been shown to deliver heat at rates ranging
from 11,000 to 25,000 Btu´s.
Cast iron
Cast iron is a live material. There are no two ovens that are identical. This is partly due to the
tolerances of the casting process, partly because the ovens are a work of craftsmanship.
Minor unevennesses may also occur in the cast iron surface.
3
1.0 Installation of your Morsø stove
Installation of woodburning stoves must be safe and legal.
If your Morsø stove is not installed correctly, it may cause a house fire. To reduce the risk
of fire, the installation instructions must be followed carefully. Contact the local building
officials about restrictions and installation inspection in your area.
Before you start installing your stove, make sure that:
-The stove and chimney connection are placed far enough from combustible materials to
meet all clearance requirements.
-The floor protection must be adequate and must be made correctly according to the requirements.
All neccessary approvals are needed from the local building officials.
The data plate, which is located on the back of the stove, provides information regarding safety
testing information, name of certified testing laboratory, and installation requirements.
Installation requirements vary in different districts, and the local building officials have the final
authorization to approve your installation. You should discuss the installation with them before
beginning. Please ask your dealer for further information.
Do not connect to any air distribution duct or system.
Important: If the installation instructions are not followed carefully, it may cause dangerous situations like chimney - and house fires. Follow the instructions carefully and
do not deviate from them as it may cause injuries to people or property.
1.1 Checking loose parts in the stove
After unpacking, check that the fire bricks are firmly in position and have not shifted in transit.
Check also that the air control works freely.
See separate Assembly Instructions for Legs, Fitting for handle, and Baffles Before starting
the initial fire, place the two cast iron baffles above the three stainless pipes that supplies
the secondary air. The baffles are enclosed in the stove on delivery. Afterwards, place the
carbowool blanket carefully above the two cast iron baffles.
Make sure that the upper heating shield, the cast iron baffles, and the carbowool blanket are
placed correctly before the fire is started.
Standard Accessories
A Morsø glove and ceramic flue connection gasket are standard accessories that usually can
be found in the ashpan or firebox area.
4
1.2 The chimney / flue system
Note that the flue system must be independently secured and must not rely on the stove
for support.
The stove must not be connected to a chimney flue serving any other appliance.
(Several flues may run up a single chimney stack; use one flueway per appliance).
Use a residential type masonry or listed type HT factory-built chimney.
High Temperature (H.T.) Chimney Standard UL-103-1985 (2100º F.) or a code-approved
masonry chimney with flue liner for the USA, and High Temperature (650ºC) Standard
ULC S-629 for Canada.
The internal dimensions of the chimney connector and chimney must not be less than 6 inches
diameter (or equivalent cross section), and should not be significantly larger than this. Too large
a section will tend to allow the flue gases to cool excessively, causing sluggishness or unpredictability in the stove’s performance.
We recommend the length of the chimney system should be at least 16 feet (not required)
above the stove in normal domestic situations, measured from the flue collar to the top of
the chimney.
Local conditions like for example - roof constructions, large trees nearby and high altitude,
may influence the chimney draft and height. Therefore, contact the local professional chimney sweep or your Morsø dealer.
Typical factory-built or masonry chimney installations
5
1.3 Flue Connection
The stove is supplied from the factory with a flue collar fitted to the top plate and a round
blanking plate blocking off the rear flue exit (behind the rear shield plate).
Use a 24 MSG black or blue chimney connector or listed double wall chimney connector. Refer to local codes and the chimney manufacturer’s instructions for precautions required for
passing a chimney through a combustible wall or ceiling. Remember to secure the chimney
connector with a minimum of three screws to the product and to each adjoining section.
The collar can be fitted to the rear outlet. Simply knock out the round panel on the rear heat
shield plate to reveal the cast iron plate. Untwist the blanking plate and the flue collar and
swap their positions. Re-secure by pushing down and tighten the enclosed screws.
Position the stove and connect to the flue system.
Wear gloves and protective eyewear when drilling, cutting or joining sections of chimney connector.
1.4 Connection to the existing chimney
A chimney connector is the double-wall or single-wall pipe that connects the stove to the chimney. The chimney itself is the masonry or prefabricated structure that encloses the flue. Chimney connectors are used only to connect the stove to the chimney.
Double-wall connectors must be tested and listed for use with solid-fuel burning appliances. Single-wall connectors should be made of 24 gauge or heavier gauge steel. Do not use
galvanized connector; it cannot withstand the high-temperatures that smoke and exhaust
gases can reach, and may release toxic fumes under high heat. The connector must be 6
inches (150mm) in diameter.
If possible, do not pass the chimney connector through a combustible wall or ceiling.
If passage through a combustible wall is unavoidable, refer to the sections on Wall PassThroughs. Do not pass the connector through an attic, a closet or similar concealed space
when installing the chimney connectors.
It is important to keep the flue gases moving smoothly in the right direction. Do not vent
into a large void at this location; rather form one continuous section all the way up. Use mild
bends (e.g. 45º vs. 90º) rather than sharp angles where a change of direction is required. All
parts of the venting must be accessible for cleaning purposes.
In horizontal runs of chimney, maintain a distance of 18 inches from the ceiling. Keep it as
short and direct as possible, with no more than two 90 degree turns. Slope horizontal runs
of connector upward 1/4 inch per foot (20 mm per metre) going from the stove toward the
chimney. The recommended maximum length of a horizontal run is 3 feet (1 metre), and the
total length should be no longer than 8 feet (2.5 metres).
Information on assembling and installing connectors is provided by the manufacturer’s instructions exactly as you assemble the connector and attach it to the stove and chimney.
Be sure the installed stove and chimney connector are correct distances from near by
combustible materials. See the clearance paragraph page 8.
Where passage through a wall or partition of combustible construction is desired, the installation shall conform to CAN/CSA-B365.
6
7
1.5 Positioning the stove
Distance to walls and lintel
When the stove is positioned near combustible materials, observe all current local and national building regulations with regards to clearances. Whatever regulations apply to your
area, do not in any case install the stove within 8 inches of combustible materials around the
sides or 16 inches above the top of the stove (fireplace installations require greater clearances above the stove - see below in the clearance chart). These distances may need to be
increased if the materials are sensitive to heat. Note also that wall paper and other decorative materials may become detached with the effects of heat and care should be taken to
ensure that they do not fall towards the stove in such an event.
When the stove is positioned near non-combustible materials, a gap of 4 inches or more is
recommended for cleaning purposes and to ensure that heat circulates around the stove
and out into the room.
If using rear exit, the floor protection must extend beneath the chimney connector and 2-in
beyond each side.
CLEARANCE REQUIREMENTS
A.
B.
C.
D.
E.
F.
G.
H.
Sidewall to unit
Backwall to unit
Cornerwall to unit
Sidewall to connector
Backwall to connector
Cornerwall to connector
Unit to ceiling
Floor to ceiling
CLEARANCE REQUIREMENTS
A.
B.
C.
D.
E.
F.
G.
H.
8
Sidewall to unit
Backwall to unit
Cornerwall to unit
Sidewall to connector
Backwall to connector
Cornerwall to connector
Unit to ceiling
Floor to ceiling
STANDARD RESIDENTIAL INSTALLATION
SINGLEWALL & DOUBLEWALL CONNECTOR
USA
CANADA
16”
6.5”
8.5”
23”
10”
17.5”
56.5”
84”
18” - 457 mm
9.5” - 241 mm
8.5” - 216 mm
25” - 635 mm
13” - 330 mm
17.5” - 445 mm
56.5” - 1435 mm
84” - 2134 mm
ALCOVE INSTALLATION WITH DOUBLE
WALL CONNECTOR
19” ( 483 mm)
9.5” (241 mm)
N/A
26” (660 mm)
14” (356 mm)
N/A
20.5” (521 mm)
48” (1219 mm)
Distance to furniture
The recommended minimum distance from stove to furniture is 30 inches. Note that some
furniture is more easily affected by heat and may need to be moved to a greater distance.
This is your responsibility.
In addition other combustible materials, away from the stove. In general, a distance of 30
inches must be maintained between the stove and moveable combustible item such as drying clothes, newspapers, firewood etc.
1.6 Mobile Home Installation
The Morsø 7110 can be installed in a mobile home if equipped with an outside combustion
air kit, a terminal cap with a spark arrestor, and if it meets the following installation requirements:
-The stove must be secured to the mobile home structure by bolting through the hearth
pad and into flooring.
-The stove must be installed with a listed Type HT chimney connector, HT Chimney, and
terminal cap with spark arrestor. Never use a single wall connector (stovepipe) in a mobile home installation.
-Floor protection requirements in section 1.5 must be followed precisely.
-In Canada, this appliance must be connected to a 6” (152 mm) factory-built chimney conforming to CAN/ULC-629M, STANDARD FOR FACTORY BUILT CHIMNEYS. Floor protection as
referenced in section 1.5 must be followed, as well as use of Canadian Floor Protector.
-Follow the chimney and chimney connector manufacturer’s instructions when installing
the flue system for use in a mobile home.
-Outside air kit should be installed according to installation guide in the kit.
-Intake air piping can be installed through the floor into a vented crawl space or through
the wall of the residence to obtain outside air.
-Install in accordance with 24 CFR, Part 3280 (HUD).
-NOTE: Top sections of chimney must be removable to allow maximum clearance of 13.5’
from ground level for transportation purposes.
9
WARNING:
NEVER DRAW COMBUSTION AIR FROM A WALL, FLOOR OR CEILING CAVITY OR FROM
ANY ENCLOSED SPACE SUCH AS AN ATTIC OR GARAGE.
DO NOT INSTALL IN A SLEEPING ROOM.
CAUTION:
THE STRUCTURAL INTEGRITY OF THE MOBILE HOME FLOOR, WALL, AND CEILING/ROOF
MUST BE MAINTAINED (I.E., DO NOT CUT THROUGH FLOOR JOIST, WALL STUD, CEILING
TRUSS, ETC.)
DO NOT USE A GRATE TO ELEVATE FIRE - BUILD FIRE DIRECTLY ON HEARTH.
Note:
Acid Protection
If acid-washing the masonry around the stove, protect the stove surface with an acid-proof
cover.
Fresh Air Inlet
Unless there is deemed to be sufficient ambient leakage of air into the room via doorways, windows
and the like, a dedicated fresh air inlet will be needed. This inlet should have 2 square inches (1250
square mm) of free air space. This is particularly important where the room is well sealed, or where
an extractor hood or ventilation system disturbs the natural air pressure. Such an inlet should not
be on a wall that is usually subject to negative pressure from normal wind pattern. Avoid placing the
inlet directly across the room from the stove, thus causing a cold air draft.
10
2.0 Operation
2.1 Before you start firing
For Use with Solid Wood Fuel Only. Do Not Overfire, If Heater or Chimney Connector
Glows You Are Overfiring. Inspect and Clean Chimney Frequently. Under Certain Conditions of use creosote buildup may occur rapidly. Because of risk of smoke and flame
spillage, operate only with door fully closed.
Caution:
Hot while in operation. Keep children, clothing and furniture away. Contact may cause
skin burns.
Do not use chemicals or fluids to start the fire.
Do not burn garbage or flammable fluids.
Do not use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter or fluid or similar liquids to start or freshen up a fire in this heater. Keep all such liquids away from the
heater while it is in use.
Choosing your fuel
All types of natural wood can be burned on your stove, but they must be well-seasoned and
dry. Once the wood is cut to length, it should be split down middle - to suit the dimensions
given below - to allow moisture to evaporate.
Cut the wood to a length of max 18 inches (45 cm) and approx. 3 to 3.5 inches (7-8 cm) in
section. If you can weigh your wood, aim for around 2 lbs. For correct combustion and heat
output, wood fuel should contain no more than 20% moisture; this can easily be checked by
using the Morsø Moisture Meter (part # 62929900).
To naturally season wood fuel, stack and store it under cover in an airy location where fresh air
can move through each piece. Some soft woods may take as little as one good summer to season whereas harder woods such as oak, maple, and elm may require seasoning up to 18 months.
Avoid overly dry wood that is gray in color as under certain conditions it can cause performance
problems, such as back-puffing and sluggishness. Well seasoned wood will be light to hold and
will show signs of cracking from the center-out in the ends. If your wood spits or sizzles when
burnt, and your stove’s door glass persistently mists up, your wood is not properly seasoned.
Never use drift wood (from the sea), whose salt content may cause corrosion, nor construction
wood that may have been impregnated with chemicals.
Caution: Do not place fuel within the installation clearances for the stove or within the
space required for loading fuel and ash removal.
Starting the First Fire
The initial fire should be small, so that the stove paint can cure and the main plates of the
stove can settle into position. Some fumes will be given off by the paint. Ventilate the room
during this phase.
The setting of the air control, lighting techniques and loading intervals will depend on chimney draft, the fuel used, the heat required and so on. Some basic techniques are outlined
below.
In principle
Your stove is fitted wih Primary and Secondary air inlets.
Primary Air is controlled using the lever situated under the ash lip of the stove. Moving the
control lever to right position will open the air inlet and will allow a supply of preheated air
to enter the firebox via the ‘airwash’ system situated inside the stove and the above glass.
11
Secondary Air is left to the firebox using the specially designed baffle at the back of the firebox. The secondary air is injected into the flue gases above the fire resulting in a cleaner, more
efficient combustion process. The supply of secondary air is fixed open and is not adjustable.
For extra safety, your stove has been fitted with a removable handle.
2.2 Lighting and loading intervals
When first lighting the stove, a large volume of air is needed. When the stove is cold, you
should leave the door open an inch or two for the first few minutes and open the primary air
supply completely. While the door is open, do not leave the stove unattended.
The ash door should never be open while the stove is in operation.
To form a reasonable bed of ash on the floor of the stove, you should use 5-6 inches thickness (2-4 pound) of dry kindling at the initial lighting. Always maintain a 1-1.5 inch (2-3 cm)
layer of ash on the floor of the combustion chamber at all other times.
1. A layer of embers will form rapidly if the stove is lit with
2 - 4 fire lighters or 7 - 10 rolled up sheets of newspaper,
underneath roughly 1-2 kg of dry kindling.
2. Fully open the secondary air supply that is controlled by
lever beneath the ash lip.
3. Light the fire.
12
4. After the paper/fire lighters have caught fire, leave the
fire door ajar about 2-3 cm, so that the chimney draws well.
5. After 5-10 minutes the chimney draft should be established, at this point close the fire door. If all the necessary
conditions are met, a nice layer of embers will start to accumulate after another 15 - 20 minutes.
6. Refuelling of your stove should be done while there are
still glowing embers in the bed. Spread the embers across
the bottom, but concentrated mostly towards the front of
the stove.
When refuelling your stove, it is recommended that you open the stove door gently for the
first 2 - 3 centimetres, then wait for a few seconds for the pressure in the flue to equalise;
you are now safe to proceed and open it all the way. By using this technique smoke spillage
can be eliminated particularly in poor chimney draft conditions. The stove door should not
be opened when the stove is being fired vigorously.
13
7. Place two pieces of fuel weighing roughly 2-4 pound and
measuring about 25 cm in length across the embers in one
layer, with spacing of roughly 1 cm between the pieces of wood.
8. When the primary air supply is opened all the way and
the door is closed, the new fuel will ignite in a few minutes.
9. Once the new fuel has taken, adjust the secondary air
amount to the desired setting; optimal combustion will continue until glowing embers are produced.
Under normal chimney draft conditions, expect to refuel
your stove every 60 - 70 minutes.
10.A new charge of wood can be added by repeating steps
6 & 7.
14
Do not for any reason attempt to increase the firing of your heater by altering the air
control adjustment range outlined in these directions.
Warning: Fireplace stoves must never be left unattended with doors open.
If doors are left partly open, gas and flame may be drawn out of the fireplace stove opening, creating risks from both fire and smoke. We recommend you to fit a smoke detector
in the room where the stove is installed.
DO NOT OVERFIRE THIS HEATER. Overfiring may cause a house fire, or can result in permanent damage to the stove. If any part of the stove glows, you are overfiring.
The maximum recommended weight of wood fuel per load is 2.5 kg/h/5.5Ibs (approx 3 split logs).
Under normal firing, the average flue temperature in the stove pipe, measured 20 cm above
the stove, is approx. 300° C (550°F). The maximum flue temperature in the stove pipe must
not exceed 450° C (750°F). If the flue temperature exceeds 450°C (750°F), it is considered
as over firing and may cause premature wear and tear of the stove.
To help gauge the correct running temperature of your stove, we recommend you use the Morsø
Flue Gas Thermometer (part # 62901200). The Flue Gas Thermometer magnetically attaches
onto the stove pipe approx 20 cm (8”) above the stove’s top plate and measures the surface temperature of the stove pipe. Please see your authorized Morsø Dealer for availability.
Draft conditions
If smoke or fumes come out of your stove when lightning up and reloading, or if the fire simply
will not respond, a poor draft is almost certainly to blame. (In a very few cases, there may be
insufficient fresh air getting into the room - see installation advice above). Take advice from
your stove supplier on how best to upgrade your flue system to improve draft.
Rules of woodburning
If you want less heat, put fewer logs on the stove and reduce the amount of air. It is still important to maintain a good layer of embers.
Less heat - less wood - less air
Greater heat - more wood - more air
Soot deposits will settle on the glass if the stove is run too slowly or if your wood is not well
seasoned.
15
3.0 Maintenance
When perfoming maintenance on your stove, always protect yourself, using safety goggles and gloves
3.1 Exterior Maintenance
The stove surface is painted with heat-resistant Senotherm paint. It is best kept clean by
vacuuming with a soft brush attachment or by wiping with a lint-free cloth.
Over a period of time, the painted surface may become slightly grey. A can of Morsø touch-up
spray paint should be available from your stove supplier. This can be applied - in accordance with
the instructions - in just a few minutes. When first firing after touching up, the stove will give off
a slight smell as the paint cures. Make sure to ventilate the room well during this phase.
3.2 Internal maintenance
Glass
If the stove is generally run at the correct temperatures, there should be little or no dirt on
the glass. If dirt does settle during lighting, most will burn off as temperatures increase.For
heavier deposits that will not burn off, use morsø glass cleaner, applied when the glass is
cold, in accordance with the instructions. Never use abrasive cleaners on the glass surface.
Reasons for dirty glass
- Fuel too wet
- Logs too large or not split
- Combustion temperatures too low
Replace broken glass immediately.
Do not operate your stove if the glass in the door is damaged.
If you need to replace the glass, it should be replaced with the high temperature ceramic
class supplied by Morsø, contact your Morsø dealer.
Installing the glass
Never install the glass when the stove is in function.
Ceramic glass replacement
Ceramic glass cannot be recycled because it has a higher
melting point that ordinary glass. If ceramic glass is mixed
with ordinary glass, the raw material is spoiled, and the
reclaiming process may be halted. Take care that the ovenproof glass does not end up among ordinary recycled
waste. That will be a great benefit to the environment.
Note: Should be handed in to a recycling station as ceramic glass.
16
1.When you open the door, you will find two small M4 unbraco screws, one in each hinge.
Unscrew the two screws, lift the door off the hinges and place it face down on a sheet of
cardboard or other nonabrasive fabric.
2.Unscrew the 4 bolts that secure the glass. (In the event that a bolt sheers off when being
unscrewed, remove the remaining body of the bolt by drilling down its centre with 1/8
inch high speed steel drill bit. Smaller drill bits may be successful, but do not use a lager
bit. Make sure the bit stays away from the edges of the bolt - this may damage the thread
in the cast iron).
3.Remove the old ceramic gaskets and clean up the surface underneath with wire wool or
emery paper to remove loose particles.
4.Place the new gasket material in position around the perimeter of the window area, making sure to pinch them to the length in such a way that they make a continuous seal. Leave
no gaps.
5.Place the new glass in position on the strips and screw home the fresh bolts and fitting
by hand.
6.Finally, give each of the bolts an extra half turn or so. The glass should held tight enough
by that cleaning will not dislodge it. Do not over-tighten the bolts as this may put excessive pressure on the glass, resulting in cracking - important!
To reduce the risk of breaking the glass, avoid striking the glass or slamming the door.
Internal service parts
The flame-path equipment - consisting of the ashpan, grate, firebricks, Cast iron fire plates, glass,
baffle and flue collar - are subject to the extremes of heat produced by the fire. From time to time,
one or other of these parts may need replacing as a matter of routine maintenance.
NOTE: The flame-path equipment, the ceramic rope and the paint finish are not covered
by guarantee.
All of these service parts can be bought from your morsø dealer, and we recommend that
damaged parts are replaced as soon as possible to avoid collateral damage.
Should the baffle be distorted by an overfire, the stove will still function, although its efficiency
may be compromised. Replace it as soon as possible.
Reasons for fast internal wear and tear
Persistent heavy firing
Soot and ashes left to accumulate
17
Gasket
The gasket around the perimeter of the doors may harden over a period of time. It should be
replaced if it becomes difficult to close the doors or if air starts to leak in around the perimeter of the doors, causing the fire to become a little less controllable. A morsø rope gasket kit
is available from your stove supplier.
3.3 Cleaning the Stove and the Flue
Check for soot above the baffle plate and around the flue outlet every month or so to start
with. If the stove suddenly becomes sluggish, check for a soot fall around the flue collar or
in the flue/chimney.
The chimney and chimney connector should be inspected at least once every two months
during the heating season to determine if a creosote buildup has occurred. If creosote has
accumulated, it should be removed to reduce the risk of a chimney fire.
Clean the flue/chimney - all the way from the stove to the flue terminal point above the house.
A good routine is to clean the flue after each heating season in any case, and inspect prior
to the season to ensure that bird’s nests or other blockages have not occurred during the
off season.
Ash disposal
Empty the ashpan on a daily basis or as needed. Ash allowed to build up towards the underside of the grate will trap heat and could cause premature failure of the grate.
Empty the ashpan according to this procedure:
Open the front door, and use a shovel or poker to stir excess ash through the ash slots in
the grate down into the ash pan. Then, open the ash door and take out the ash pan, making
sure to keep it level to avoid spilling ash.
Dispose the ash in a metal container with a tight fitting lid.
The closed container of ashes should be placed on a noncombustible floor or on the ground,
well away from all combustible materials, pending final disposal. If the ashes are disposed of
by burial in soil or otherwise locally disperded, they should be retained in the closed container
until all cinders have thoroughly cooled.
Return the ash pan to its original position in the stove, and close the ash door.
Caution:
Never empty a stove in operation.
Never use your household or shop vacuum cleaner to remove ash from the stove; always
remove and dispose of the ash properly.
Creosote - formation and need for removal
When wood is burned slowly, it produces tar and other organic vapors, which combine with expelled moisture to form creosote. The creosote vapors condense in the relatively cool chimney
flue of a slow-burning fire. As a result, creosote residue accumulates on the flue lining. When
ignited this creosote makes an extremely hot fire. When burning wood, the chimney and chimney
connector should be inspected at least once every two months during the heating season to determine if a creosote buildup has occurred. If creosote has accumulated, it should be removed to
reduce the risk of a chimney fire.
18
Chimney sweeping
Inspect the system regularly during the heating season as part of a regular maintenance schedule. To inspect the chimney, let the stove cool completely. Then, using a mirror, sight up through
the flue collar into the chimney flue. If you cannot inspect the flue system in this fashion, the
stove must be disconnected to provide better viewing access.
Clean the chimney using a brush the same size and shape as the flue liner. Run the brush up
and down the liner, causing any deposits to fall to the bottom of the chimney where they
can be removed through the clean-out door.
Clean the chimney connector disconnecting the sections, taking them outside, and removing any deposits with a stiff wire brush. Reinstall the connector sections after cleaning, being sure to secure the joints between individual sections with sheet metal screws.
If you cannot inspect or clean the chimney yourself, contact your local Morsø Dealer or a
professional chimney sweep.
If you do experience a chimney fire, act promptly and:
1. Close the air control.
2. Get everyone out of the house.
3. Call the Fire Department.
Annual maintenance
Before the heating season, perform a thorough cleaning, inspection and repair:
Thoroughly clean the chimney and chimney connector.
Inspect the chimney for damage and deterioration. Replace weak sections of prefabricated
chimney. Have a mason make repairs to a masonry chimney.
Inspect the chimney connector and replace any damaged sections.
Check gasketing for wear or compression, and replace if necessary.
Check the glass for cracking; replace if needed.
Check door and handles for tightness. Adjust if needed.
3.4 Leaving the stove for extended periods
Important:
If the stove is to be left unused for any period of time, clean it out thoroughly and leave the
air control slightly open to allow airflow. Make sure that the flue does not allow rainwater
to come anywhere near the stove; install a chimney cap, but do not block off the flue completely.
These measures should ensure there is a slight movement of air through the stove, and that
the body of the stove remains dry, right into the corners.
Any ash left within an unfired stove can attract moisture like blotting paper. If moisture is allowed to settle within the stove, rust will form. Rust expands as it takes a grip. This can lead
to undue pressure on the stove joints, and this in turn may result in damage to the stove.
NOTE: It is best to thoroughly clean the stove after the heating season has concluded.
Adding a dessicant, such as kitter litter, into the ash pan helps absorb moisture during
the summer months. Be sure to remove this prior to the heating season.
Thank you for buying a morsø stove.
We hope you have many years of carefree warmth in its company. Some initial experimentation with loading and running techniques will decide your normal routine. If you have any
problems after this short learning phase, please refer to your stove dealer. Should they be
unable to help for any reason, please contact us in writing at the address on the front of
this publication.
19
20
5
77
62
94
62
64
77
84
93
84
3
64
47
58
34
92
42
33
96
53
34
91
93
95
42
95
42
83
7140
DIN
67
18
83
46
46
33
2
21
50
64
53
62
15
26
29
95
41
17
76
64
NA
53
77
12
50
34
64
10
33
59
44
65
64
89
69
88
64
60
80
75
64
30
66
14
46
63
28
79 50
50
48
25
86
53
54
64
85
54
50
64
27
64
64
59
53
65
64
96
33
37
78
30
64
73
71
64
78
50
74
23
74
56
61
61
32
24
16
36
96
33
59
64
53
66
68
73
72
70
7
50
35
9
1
82
56
61
13
52
64
53
31
64
64
11
50
64
8
Påført pos. 94 og 95.
Fjedersystem ændret.
h
g
Released:
Reservedelstegning
U:\udv\Tegninger\7100\7110 Samling.SLDASM
Itemno.:
-
A2
7100-501 l
Drawing no.:
Date:
19.08.03
KDU
19.08.05
14.06.2006
09.01.07
07.05.2008
19.02.2009
52
65
40
Sign.:
KDU
RSV
KDU
RSV
RSV
65
55
59
This drawing is Morsø Jernstøberi A/S' property and must no be sold, lended or copied without any written authorization from the company.
Location of file:
Drawingtype:
Model no.
Morsø 7110
Construction:
81
Title:
Rev. Revisions
Air kit som option og mont. af røgtude.
Påført pos. 95 ved askedør.
j
4
k
Ændret pos. på lille greb fra 87 til 89.
90
38
l
64
63
Scale:
-
64
51
64
90
Option
Weight:
87
50
39
Format:
20
64
63
Material:
19
6
22
33
3.5 Parts diagram for model Morsø 7110
Date of print: 10-11-2010
3.6 Parts list for model Morsø 7110
Pos. No. Parts
1
Base plate
2
Front frame
3Door
4
Side plate, right
5
Side plate, left
6
Rear plate
7
Top plate
8
Rear air duct 9
Button air duct
10
Front air duct
11
Secondary air duct, right
12
Secondary air duct, left
13Leg
14
Frame for ash door
15
Ash door
16Grate
17
Locking device
18
Ceramic glass
19
Brick, back
20
Brick, side, right
21
Brick, side, left
22
Radiant shielding, rear
23
Radiant shielding, bottom
24
Ash tray
25
Primary damper
26Handle
27
Brick fitting
28
Fitting for pin at ach tray
29Screw
30
Secondary tube, big
31
Secondary tube, litle
32Cover
33
Flue collar
34
Fitting w. thread for flue collar
35
Fitting for baffle plate
36
Distance tube
37
Distance tube
38
Distance tube
39
Distance tube
40
Air adaptor
41
Hinge pin
42
Hinge pin
44
Cotter pin
46
Cotter pin
47
Glass fitting
48Screw
49Screw
50Screw
51Screw
52Screw
447101xx
447102xx
447103xx
447119xx
447120xx
447106xx
447107xx
447108xx
447109xx
447110xx
34711100
34711200
447113xx
447114xx
447115xx
34711600
797117xx
79710000
79710100
79710200
79710300
547101xx
547102xx
71710300
71710400
71710500
71710600
71710700
71710900
71711000
44261000
44344100
44256700
545006
545007
541439
542635
54710100
71360600
545008
54503000
791870
79187200
54146361
21
3.6 Parts list for model Morsø 7110
Pos. No. Parts
53Screw
54Screw
55Screw
56Screw
57Screw
58Screw
59Screw
60Screw
61Washer
62Washer
63Washer
64Washer
65Screw
66
Baffle plate, cast iron
67
Tightening tape for glass
68Insulation
69
Primary handle
70
Baffle plate, upper
71
Stop fitting, left, for baffle plate
72
Stop fitting, right, for baffle plate
73
Fitting for baffle plate
74Screw
75Nuts
76
Adaptor for handle
77Screw
78Screw
79
Fitting for primary handle
80Screw
81
Fitting for handle
82
Fitting for leg
85
Locking fitting for sek. pipe
86Screw
87Washer
88Clasp
89
Bakelite handle 36mm
94
Hinge pin
95Washer
96
Stop bar
22
34711800
79074500
79710500
71711161
79710400
71711200
71711300
71711400
71710800
717115xx
717117xx
717118xx
71712061
74150804
736210
791270xx
79118200
74701000
544541
23
24
Guarantee
Product Registration
MORSØ 10 YEAR GUARANTEE CERTIFICATE
Behind every Morsø stove is more than 160 years of dedicated stove design and manufacturing experience. Quality control has always been at the heart of the production process and detailed measures
have been put into place at all key stages of the build. Accordingly, provided that the stove has been
supplied by an authorised Morsø dealer, Morsø will offer a 10-Year Manufacturers Guarantee against
manufacturing defect to any of the main exterior body parts of its stoves.
Read more about ”Morsø 10 years guarantee/product registration card” and
REGISTER your new Morsø stove online:
http://international.morsoe.com/warranty-registration
Morsø Jernstøberi A/S - 14.12.2015 - 72711000
25
26
27
IMPORTANT!
How to heat safely for the environment and yourself!
•Use only dry wood
Use only dry (max. 20% moisture content)
and untreated wood. The fuel must be split
and 8 - 12 cm thick.
•Light
Light with dry kindling (use 1 - 2 kg). Leave
the door ajar and stay close to the stove
during the lighting phase.
•Good layer of embers
Be certain to have a good layer of embers before refilling. The wood should
light within 2 minutes. If the logs do
not ignite it may, in an extreme case,
cause the flue gases to ignite which
may pose a risk to material damage or
personal injury.
•Refuelling
When refuelling use 2 - 3 pieces of wood
- no more than 2 - 2.5 kg.
•Ensure adequate air
I.e. clear and yellow flames.
•Never burn overnight
Morsø Jernstøberi A/S - 14.12.2015 - 72711000
28
MORSØ JERNSTØBERI A/S . DK-7900 NYKØBING MORS
E-Mail: stoves@morsoe.com · Website: www.morsoe.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising