7271 kit for Hammond

7271 kit for Hammond
LESLIE CONSOLE CONNECTOR KIT 7271
INSTALLATION INSTRUCTIONS
For Hammond Consoles: Ml, M2, M3, M100, L100
To Leslie Models: 120, 125, 145, 147, 147RV, 225, 247, 247RV.
MULTIPLE SPEAKER INSTALLATIONS: For complete information, consult the
Owner's Manual of the LESLIE speaker to be added.
Contents of Kit: 1 - Console Adapter
1 - 6 Conductor Cable
1 - Console Connector
1 - Instructions
5 - Insulated Staples
1 - Oiler
2 - Screws, 8 x 1/2
4 - Screws, 6 x 1/2
2 - Connector, Tab, Female
2 - Connector, Tab, Male
027011
017277
012617
034447
028464
053025
029132
029124
029389
029371
1 - Tremolo Control
012625 Brown
012633 Ebony
012641 Ivory
1 - Echo Control
029397 Brown
029405 Ebony
029413 Ivory
To Install the Kit:
1. Attach the Echo and Tremolo control switches to the wooden rail in front of the
lower manual with the wood screws provided. Use the two mounting holes in each
case which best center the screws.
2. Remove the console dust cover, and pass the switch cables under the right side of
the lower manual into the upper compartment of the console. If no opening is
provided, drill a 7/8" hole in the keyboard shelf just under the lower manual.
3. Pass the switch cables into the lower compartment through the slot in the rear
edge of the shelf.
4. Locate the console connector midway up the inside left-hand side panel of the
lower compartment, making sure the adapter and control cables will reach. Fasten
the chassis in place using the wood screws provided.
5. Plug the switch control cables into their sockets on the console connector chassis.
6. Fit the 5 contact socket of the console adapter onto the 5 pin plug of the console
connector chassis.
7. Ml, M2:
a) Disconnect and discard the 5 contact plug and socket assembly from the adapter
at the screw terminals.
Page 1 of 4
b) Remove the green speaker wire from the console amplifier output terminal and
connect it to the screw terminal on the green adapter wire. Cover this connection
with a plastic sleeve.
c) Connect the red adapter wire to the output terminal from which you have just
removed the green speaker wire.
d) Connect the black adapter wire to the amplifier output terminal to which the
black speaker wire is connected. Do not remove the wire already attached to this
terminal.
e) Connect the gray and blue adapter wires to the two AC terminals on the console
amplifier controlled by the console power switch.
f) Plug the 6-pin plug from the tone cabinet cable into the 6-contact socket on the
console connector.
g) Replace the console dust cover.
h) Set the console load resistor on the tone cabinet amplifier at 8 ohms, and adjust
the speaker volume control as indicated in the manual. The installation is now
complete.
M3:
a) Remove the 5-pin console speaker plug from the amplifier and plug it into the 5contact adapter socket.
b) Insert the 5-pin adapter plug into the socket from which you have just removed
the speaker plug.
c) Solder the gray and blue adapter wires to the two AC terminals on the console
amplifier controlled by the console power switch.
d) Plug the 6-pin plug on the tone cabinet cable into the 6-contact socket on the
console connector.
e) Replace the console dust cover.
f) Set the console load resistor on the tone cabinet amplifier at 8 ohms, and adjust
the speaker volume control as indicated in the manual. The installation is now
complete.
L-100, M-100:
a) Cut the wires attaching the 5-pin plug and socket assembly to the adapter at a
point just behind the screw terminals and strip the wires 1/4 inch.
Page 2 of 4
b) Solder the tab connectors provided to the stripped wires as follows:
Red - Male
Black - Female
Green - Female
c) Remove the green amplifier output wire from the speaker terminal and connect it
to the red wire from the console adapter. Cover this connection with a plastic
sleeve. N0TE: 0n late model M-100 consoles, both a red and a green wire are
connected to the speaker at this point. Remove both wires and clip off the
connector tabs. Do not place a connector tab on the console adapter red wire,
but strip all three wires about 1/2 inch. Connect them together with the wire nut
provided.
d) Connect the green adapter wire to the speaker terminal from which you have just
removed the green wire.
e) Connect the black adapter wire to the extra tab on the second console speaker.
Do not disturb the black wire already attached.
f) Solder the gray and blue adapter wires to the two AC terminals on the console
amplifier controlled by the console power switch.
g) Plug the tone cabinet cable into the 6-contact socket on the console connector.
h) Replace the console dust cover.
i) Set the console load resistor on the tone cabinet amplifier at 8 ohms, and adjust
the speaker volume control as indicated in the manual. The installation is now
complete.
PARTS LAYOUT
012617 CONSOLE CONNECTOR
Page 3 of 4
Control Switch Parts List:
Echo Control
Echo Switch Case
029199 Brown
029207 Ebony
029215 Ivory
Switch Case Cover
048702 Brown
048710 Ebony
048728 Ivory
Switch Knob
048066 Brown
048074 Ebony
Switch Retainer (2 req'd)
Switch Only
5-Pin Plug
048116
010249
021238
Tremolo Control
Tremolo Switch Case
012260 Brown
012278 Ebony
012286 Ivory
Switch Case Cover
048702 Brown
048710 Ebony
048728 Ivory
Switch Knob
048066 Brown
048074 Ebony
Switch Retainer (2 req'd) 048108
Switch Only
042911
2-Pin Plug
029165
Page 4 of 4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising