PanelView 1000 Terminals

PanelView 1000 Terminals
Installation Instructions
PanelView 1000 Terminals
Catalog Numbers 2711-K10Cxx, 2711-K10Gxx, 2711-T10Cxx, 2711-T10Gxx
Topic
Page
Important User Information
2
European Union Directive Compliance
3
Wiring and Safety Guidelines
4
Hazardous Location Considerations
5
Enclosures
6
Required Tools
6
Mounting Dimensions
6
Cutout Dimensions
7
Clearances
8
Installing Terminal in a Panel
8
Installing the Memory Card Retainer
10
Connecting AC Power
11
Connecting DC Power
13
EtherNet/IP Protocol
14
ControlNet Protocol
15
Battery Removal and Disposal
15
2
PanelView 1000 Terminals
Important User Information
Solid state equipment has operational characteristics differing from those of electromechanical equipment.
Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls (Publication
SGI-1.1 available from your local Rockwell Automation sales office or online at
http://literature.rockwellautomation.com) describes some important differences between solid state
equipment and hard-wired electromechanical devices. Because of this difference, and also because of the
wide variety of uses for solid state equipment, all persons responsible for applying this equipment must
satisfy themselves that each intended application of this equipment is acceptable.
In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages
resulting from the use or application of this equipment.
The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many
variables and requirements associated with any particular installation, Rockwell Automation, Inc. cannot
assume responsibility or liability for actual use based on the examples and diagrams.
No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits,
equipment, or software described in this manual.
Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell
Automation, Inc., is prohibited.
Throughout this manual, when necessary, we use notes to make you aware of safety considerations.
WARNING
IMPORTANT
ATTENTION
Identifies information about practices or circumstances that can cause an explosion in
a hazardous environment, which may lead to personal injury or death, property
damage, or economic loss.
Identifies information that is critical for successful application and understanding of
the product.
Identifies information about practices or circumstances that can lead to personal injury
or death, property damage, or economic loss. Attentions help you identify a hazard,
avoid a hazard and recognize the consequences.
SHOCK HAZARD
Labels may be on or inside the equipment, for example, a drive or motor, to alert
people that dangerous voltage may be present.
BURN HAZARD
Labels may be on or inside the equipment, for example, a drive or motor, to alert
people that surfaces may reach dangerous temperatures.
Publication 2711-IN036J-EN-P - November 2009
PanelView 1000 Terminals
IMPORTANT
3
This document is for both current series and revision terminals. Check
terminal back label for final ratings and certifications.
This document describes how to mount a PanelView 1000 terminal in a panel or enclosure
and apply power.
•
•
•
•
•
•
•
•
•
•
•
European Union Directive Compliance
wiring and safety guidelines
hazardous locations
enclosures
required tools
mounting dimensions
cutout dimensions
clearances
installing the terminal in a panel
installing the memory card retainer
connecting AC or DC power
For more information on PanelView Operator Terminals, refer to Publication 2711-UM014.
European Union Directive Compliance
If a PanelView 1000 Operator Terminal is installed within European Union or EFTA regions
and has a CE mark, the following regulations apply.
Publication 2711-IN036J-EN-P - November 2009
4
PanelView 1000 Terminals
EMC and Low Voltage Directives
This apparatus is tested to meet Council Directive 2004/108/EC Electromagnetic
Compatibility (EMC) and 2006/95/EC Low Voltage Directive, using the following standards,
in whole or in part.
PV1000G
PV1000C
Emissions (Class A: Industrial)
EN61000-6-4:2001
x
x
Immunity (Industrial) EN61000-6-2:1999
x
x
Programmable Controllers
(Equipment Requirements and Tests) EN61131-2
x
x
Low Voltage Directive
(Safety Sections of EN61131-2)
x
x
Intended Use of Product
According to these Standards, the factor which determines, for EMC purposes, whether an
apparatus is deemed to be “Industrial” or “Residential, commercial and light industrial”, is
given as follows:
Apparatus covered by this standard is not intended for connection to a public mains
network but is intended to be connected to a power network supplied from a high- or
medium-voltage transformer dedicated for the supply of an installation feeding a
manufacturing or similar plant.
When installed in Europe, any other application is in contravention of European Union
Directives, and a breach of these laws.
The PanelView 1000 grayscale terminals are certified for direct connection to a low-voltage
public mains supply or to a dedicated source, which is intended to interface to a low-voltage
public mains supply.
Korean Radio Wave Suitability Registration - This equipment is registered for
Electromagnetic Conformity Registration as business equipment (A), not home equipment.
Sellers or users are required to take caution in this regard.
Wiring and Safety Guidelines
Install the PanelView terminal using Publication 70E, Electrical Safety Requirements for
Employee Workplaces. In addition to the NFPA general guidelines, follow these
recommendations:
• Connect the PanelView terminal to its own branch circuit.
Protect the input power source by a fuse or circuit breaker rated at no more than 15
Amps.
Publication 2711-IN036J-EN-P - November 2009
PanelView 1000 Terminals
5
• Route incoming power to the PanelView terminal by a separate path from the
communication cable.
• Where power and communication lines must cross, they should cross at right angles.
Communication lines can be installed in the same conduit as low level DC I/O lines
(less than 10 Volts).
• Grounding minimizes noise from electromagnetic interference (EMI) and is a safety
measure in electrical installations. To avoid EMI, shield and ground cables
appropriately.
• A source for grounding recommendations is the National Electrical Code published
by the National Fire Protection Association of Boston.
Hazardous Location Considerations
This equipment is suitable for use in Class I, Division 2, Groups A, B, C, D; Class II, Division
2, Groups F and G; Class III; or non-hazardous locations only. The following WARNING
statement applies to use in hazardous locations.
WARNING
EXPLOSION HAZARD
• Substitution of components may impair suitability for Class I, Class II, Class III.
• Do not replace components or disconnect equipment unless power has been
switched off or the area is known to be non-hazardous.
• Do not connect or disconnect components unless power has been switched off
or the area is known to be non-hazardous.
• This product must be installed in an enclosure. All cables connected to the
product must remain in the enclosure or be protected by conduit or other means.
• All wiring must comply with N.E.C. article 501-4(b), 502-4(b), 503-3(b) as
appropriate.
See the nameplate on terminal for hazardous locations certifications.
ATTENTION
In Class I, Class II, Class III Hazardous locations, the PanelView terminal must be
wired per the National Electric Code as it applies to hazardous locations. Peripheral
equipment must also be suitable for the location in which it is installed.
Publication 2711-IN036J-EN-P - November 2009
6
PanelView 1000 Terminals
Enclosures
The terminals must be mounted in an environment that provides EN/IEC 61131-2 Pollution
degree 2 protection.
Mount the terminal in a panel or enclosure to protect the internal circuitry. The terminal
meets NEMA Type 12/13 or 4X (indoor use) ratings only when mounted in a panel or
enclosure with the equivalent rating.
Allow enough space within the enclosure for adequate ventilation. Consider the heat
produced by other devices in the enclosure. The ambient temperature around the terminal
must be between 0…55 ° C (32…131 ° F) for PV1000 terminals.
Make provisions for accessing the back panel of the terminal for wiring, maintenance,
installing a memory card, and troubleshooting.
Required Tools
Other than the tools required to make the panel cutout, the tools required for installation are:
• small slotted screwdriver
• torque wrench (N•m, lb•in) with slotted or phillips head driver
Mounting Dimensions
The following figures show mounting dimensions for the PanelView 1000 grayscale and color
terminals.
PanelView 1000 Touch Terminal
282 mm
(11.11 in.)
6.9 mm
(0.27 in.)
90 mm
(3.54 in.)
370 mm
(14.58 in.)
Publication 2711-IN036J-EN-P - November 2009
Top View
112 mm
(4.40 in.)
PanelView 1000 Terminals
7
PanelView 1000 Keypad Terminal
282 mm
(11.11 in.)
6.9 mm
(0.27 in.)
Top View
90 mm
(3.54 in.)
112 mm
(4.40 in.)
423 mm
(16.64 in.)
Cutout Dimensions
Use the full size template shipped with the PanelView 1000 terminal to mark the cutout
dimensions. The following figures show reduced size cutouts.
PanelView 1000 Keypad Terminals
257 mm
(10.11 in.)
Recommended Panel
Cutout Dimensions
390 mm
(15.35 in.)
PanelView 1000 Touch Screen Terminals
257 mm
(10.11 in.)
Recommended Panel
Cutout Dimensions
338 mm
(13.29 in.)
Publication 2711-IN036J-EN-P - November 2009
8
PanelView 1000 Terminals
Clearances
Allow adequate space for mounting, air flow, maintenance, and for installing a memory card
and function key legend inserts.
Side, Top and Bottom Clearances
Leave 51 mm (2 in.) for
Mounting and Air flow
TERMINAL CUTOUT Use Full
Size Template shipped with
Terminal Front View
Leave 51 mm (2 in.) for
Mounting and Air Flow
6.9 mm
(0.27 in.)
222 mm (8.73 in.)
is required to
insert and remove
a memory card
with the memory
card retainer.
Leave 51 mm (2 in.) for Mounting
and Wiring Connections
Leave 51 mm (2 in.) for Mounting, Air
Flow and Legend Insert
90 mm
(3.54 in)
card
Back Clearance
Memory Card Retainer
Installing Terminal in a Panel
To install the PV1000 terminal in a panel:
ATTENTION
Disconnect all electrical power from the panel before making the cutout.
Make sure the area around the panel cutout is clear.
Take precautions so that metal cuttings do not enter any components that may already be
installed in panel.
Failure to follow this warning may result in personal injury or damage to the panel
components.
Publication 2711-IN036J-EN-P - November 2009
PanelView 1000 Terminals
9
1. Cut an opening in the panel using the panel cutout provided with the terminal.
Remove any sharp edges or burrs.
2. Make sure the terminal sealing gasket is properly positioned on the terminal as shown
below. This gasket forms a compression type seal. Do not use sealing compounds.
Sealing Gasket
3. Although the keypad legend insert can be installed any time, we recommend that you
install it after the terminal is installed.
4. Place the terminal in the panel cutout.
5. Install the 6 mounting clips (2 on top, 2 on bottom, 1 on each side); the ends of the
clips slide into the slots on the terminal. Tighten the clip mounting screws by hand
until the gasket seal contacts the mounting surface uniformly.
Protective Installation Labels
Install 6 Mounting Clips:
Top - Left and Right Slots
Bottom - Left and Right Slots
Sides - Left and Right Slots
Publication 2711-IN036J-EN-P - November 2009
10
PanelView 1000 Terminals
6. Alternately tighten the mounting clip screws to a torque of 1.13 N•m
(10 lb•in). Do not overtighten. Bezel may not contact enclosure surface.
ATTENTION
Tighten mounting clips to a torque of 1.13 N•m (10 lb•in) to provide a proper
seal and to prevent potential damage to the terminal. Allen-Bradley assumes
no responsibility for water or chemical damage to the terminal or other
equipment within the enclosure because of improper installation.
7. Remove the 2 protective labels covering the top vents of the terminal.
ATTENTION
Remove the protective installation labels covering the top vents to prevent
overheating and damage to the terminal.
Installing the Memory Card Retainer
The memory card retainer is required for UL508 installations where a memory card is
inserted in the card slot. The retainer protects against Electrostatic Discharge (ESD) up to
15KV and prevents accidental removal of a memory card in high vibration environments.
To attach the memory card retainer:
Retainer Base
Memory Card
Retainer
Base Mounting Screws
Publication 2711-IN036J-EN-P - November 2009
PanelView 1000 Terminals
11
1. Secure the base of the retainer over the existing memory card slot using the 2 screws
provided. Tighten screws to a torque of 0.7…0.9 N• m (6 …8 lb•in).
2. Insert the memory card and install the retainer until it is properly seated.
3. To remove the retainer, press the tabs on each side and pull.
Connecting AC Power
Below are AC electrical ratings for the PanelView 1000 terminals.
Terminal Type
Supply Voltage
Power Consumption
PV1000G and PV1000C
85…264V AC, 47…63 Hz
55VA maximum
The PanelView 1000 terminal is an EN/IEC 61131-2 Equipment Class I device and requires
you to connect the
(Protective Earth) terminal to an earth conductor.
ATTENTION
The terminal is designed for safe use when installed in a suitably rated NEMA Type 12,
13, 4X (indoor use only), IP54 or IP65 enclosure.
ATTENTION
Do not apply power to the terminal until all wiring connections have been made. Failure
to do so may result in electrical shock.
ATTENTION
Explosion Hazard - Do not connect or disconnect equipment while circuit is live unless
area is known to be non-hazardous.
Publication 2711-IN036J-EN-P - November 2009
12
PanelView 1000 Terminals
To connect the AC power to the PV 1000 terminals:
1. Secure the AC power wires to the L1 and L2N screws on the terminal block.
2. Secure the Earth Ground/Protective Earth wire to the
block.
screw on the terminal
Improper wiring of the power terminals may result in voltage at the
communication connector shells. Refer to the figure below when wiring.
ATTENTION
3. Apply power to the terminal.
120/240V AC, 3 Wire,
U.S. Color Code
L1 L2
Black
(Line)
White
(Neutral)
120/240V AC, 3 Wire,
European Harmonized
Color Code
L1 L2
Green (Earth
Ground)
Brown
(Line)
Green/Yellow
(Protective Earth)
Blue
(Neutral)
To Power Source
Publication 2711-IN036J-EN-P - November 2009
To Power Source
Power Terminal
Block (fixed)
PanelView 1000 Terminals
13
Connecting DC Power
The L1 versions (Catalog No. 2711-T10G1L1) of the PV1000 terminals connect to a 24V DC
power source.
The electrical ratings for the PanelView 1000 terminals is shown below. Electronic circuitry
and an internal fuse protect the terminals from reverse polarity and over-voltage conditions.
Terminal Type
Supply Voltage
Power Consumption
PV1000G
18…32V DC, (24V DC nominal)
24 Watts max. (1.0 Amps @ 24V DC)
PV1000C
18…32V DC, (24V DC nominal)
24 Watts max. (1.0 Amps @ 24V DC)
ATTENTION
Do not connect the PanelView terminal to an AC power source. Connecting to an AC
power source may damage the terminal.
ATTENTION
The PanelView terminal is designed for safe use when installed in a suitably rated NEMA
Type 12, 13, 4X (indoor use only), IP54 or IP65 enclosure.
To connect DC power to the PV1000 terminal:
1. Secure the DC power wires to the DC negative and DC positive screws on the
terminal block.
2. Secure the Earth Ground wire to the
ATTENTION
screw on the terminal block.
Explosion Hazard - Do not connect or disconnect equipment while circuit is live unless
area is known to be non-hazardous.
Publication 2711-IN036J-EN-P - November 2009
14
PanelView 1000 Terminals
ATTENTION
Do not apply power to the terminal until all wiring connections have been made. Failure
to do so may result in electrical shock.
3. Apply 24V DC power to the terminal.
Power Terminal
Block (fixed)
+
Earth Ground
DC Negative
DC Positive
EtherNet/IP Protocol
The PanelView terminal is initially set to DHCP with BootP support (Dynamic Host
Configuration Protocol) enabled. If your network has a DHCP/BootP server, you can
connect the PanelView terminal to the EtherNet/IP network and the DHCP/BootP server
will automatically establish an IP address. If your network does not have a DHCP/BootP
server, you need to program an IP address. This is done by accessing Configuration Mode on
the PanelView terminal and selecting Communication Setup. For details, refer to the
PanelView Standard Operator Terminals Manual.
IMPORTANT
If a PanelView is connected to an EtherNet/IP network and has the same IP address as
another device on the network, both devices will drop off the network.
Publication 2711-IN036J-EN-P - November 2009
PanelView 1000 Terminals
15
ControlNet Protocol
IMPORTANT
When making ControlNet connections, only use the PanelView Channel B for redundant
communications. Connecting Channel B to a Channel A only ControlNet network will
result in:
• the PanelView not being able to communicate over the network
• a PanelView communications fault after several minutes
ControlNet Communication Port
ATTENTION
PanelView Plus terminals with ControlNet communications ports include a Network
Applications Port (NAP). This port is for temporarily connecting programming terminals
to devices on a ControlNet network, and are not intended for continuous operation.
Battery Removal and Disposal
The terminal contains a lithium battery, which is intended to be replaced during the life of the
product.
ATTENTION
The clock module contains lithium. Do not dispose of the battery in a fire or incinerator, or
the clock module may explode. Follow disposal regulations in your area for lithium
battery disposal.
At the end of its life, the battery contained in this product should be collected separately
from any unsorted municipal waste.
Publication 2711-IN036J-EN-P - November 2009
16
PanelView 1000 Terminals
Follow these steps to remove or replace the battery.
2
1
3
6
4
7
Publication 2711-IN036J-EN-P - November 2009
5
8
PanelView 1000 Terminals
17
Notes:
Publication 2711-IN036J-EN-P - November 2009
18
PanelView 1000 Terminals
Notes:
Publication 2711-IN036J-EN-P - November 2009
PanelView 1000 Terminals
19
Publication 2711-IN036J-EN-P - November 2009
Rockwell Automation Support
Rockwell Automation provides technical information on the Web to assist you in using its
products. At http://support.rockwellautomation.com, you can find technical manuals, a
knowledge base of FAQs, technical and application notes, sample code and links to software
service packs, and a MySupport feature that you can customize to make the best use of these
tools.
For an additional level of technical phone support for installation, configuration and
troubleshooting, we offer TechConnect support programs. For more information, contact
your local distributor or Rockwell Automation representative, or visit
http://support.rockwellautomation.com.
Installation Assistance
If you experience a problem within the first 24 hours of installation, please review the
information that's contained in this manual. You can also contact a special Customer Support
number for initial help in getting your product up and running.
United States
1.440.646.3434
Monday – Friday, 8 a.m. – 5 p.m. EST
Outside United
States
Please contact your local Rockwell Automation representative for any
technical support issues.
New Product Satisfaction Return
Rockwell Automation tests all of its products to ensure that they are fully operational when
shipped from the manufacturing facility. However, if your product is not functioning and
needs to be returned, follow these procedures.
United States
Contact your distributor. You must provide a Customer Support case number
(call the phone number above to obtain one) to your distributor in order to
complete the return process.
Outside United
States
Please contact your local Rockwell Automation representative for the return
procedure.
PanelView, PanelView 1000, Allen-Bradley, Rockwell Automation, and TechConnect are trademarks of
Rockwell Automation, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
Publication 2711-IN036J-EN-P - November 2009
Supersedes Publication 2711-IN036I-MU-P - August 2007
Copyright © 2009 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising