N750 Wireless Dual Band Gigabit Router WNDR4300

N750 Wireless Dual Band Gigabit Router WNDR4300
Installation Guide
N750 Wireless Dual Band Gigabit Router
Step 1:
Step 2:
Premium Edition
WNDR4300
Unplug the power
to turn off your modem.
Connect one end of the
yellow Ethernet cable
to your modem, and the
other end to the Internet
port on your router.
Package Contents:
(not included)
Laptop or desktop
computer
Step 5:
Connect your computer
to the router
DSL
or cable
Internet
Power On/Off
Power On/Off
Modem
Ethernet cable
Step 3:
Plug in the power to
turn on your modem.
N750 Wireless Router
Power adapter
Step 6:
N750 Wireless Router
Open a browser.
Step 4:
Wait approximately 2 minutes
until your modem turns on.
Connect the power adapter to the
router, then plug it into an outlet.
If your modem has
a battery backup,
first remove and reinsert
the battery before connecting
your modem to power.
Wait for the 2.4 GHz LED (
to light.
2.4 GHz
)
If none of the LEDs light, make sure
that the Power On/Off button is in the
on position (pushed in).
If the web page does not
display, close and reopen
the browser, then enter
http://www.routerlogin.net
in the address bar, or
check the “Troubleshooting”
section on the back of
this installation guide.
Preset Wireless Security
This product has a unique WiFi network name (SSID) and network key (password).
The default SSID and password are uniquely generated for every device (like a
serial number), to protect and maximize your wireless security. This information is
located on the label on the bottom of the product.
Connect Wireless Devices to Your Router
Troubleshooting
Choose either the manual or Wi-Fi Protected Setup (WPS) method to add wireless
computers, and other devices to your wireless network.
The browser cannot display the web page.
Manual Method
1.
NETGEAR recommends that you do not change the preset SSID or password. If you
do change the settings, the information on the bottom of the product does not apply.
2.
Find the preset wireless settings on your router and record them here:
WiFi network name (SSID) ________________________________
Network key (password) __________________________________
If you change the preset wireless settings, record them here:
Wireless network name (SSID) _______________________________
Look for the preset NETGEAR wireless network name (SSID), and select it.
The SSID is located on the product label on the bottom of the router.
•
•
Support
3.
Enter the preset password (or your custom password if you changed it), and
click Connect.
Thank you for purchasing this NETGEAR product.
4.
Repeat steps 1–3 to add other wireless devices.
WPS Method
If your wireless device supports WPS (Wi-Fi Protected Setup)—NETGEAR calls
this method Push 'N' Connect—you might be prompted to press the WPS button on
the router instead of entering a password. If you are prompted to press the WPS
button:
1.
Press the WPS button
2.
Within 2 minutes, press the WPS button on the client device, or follow the
WPS instructions that came with your wireless device to complete the WPS
process. The device will then be connected to your router.
3.
on the router.
After installing your device, locate the serial number on the label of your product and
use it to register your product at https://my.netgear.com. You must register your
product before you can use NETGEAR telephone support. NETGEAR recommends
registering your product through the NETGEAR website. For product updates and
web support, visit http://support.netgear.com. NETGEAR recommends that you use
only the official NETGEAR support resources.
You can get the user manual online at http://downloadcenter.netgear.com or
through a link in the product’s user interface. For the current EU Declaration of
Conformity, visit http://support.netgear.com/app/answers/detail/a_id/11621/. For
regulatory compliance information, visit http://www.netgear.com/about/regulatory/.
See the regulatory compliance document before connecting the power supply.
Get the genie app.
Repeat this process to add other WPS wireless devices.
Note: WPS does not support WEP security. If you try to connect a WEP client
to your network using WPS, it does not work.
Select Wireless Settings to locate your wireless password.
•
•
Make sure that the computer is connected to one of the four LAN Ethernet ports,
or wirelessly to the router.
Make sure that the Wireless LED is lit.
Close and re-open the browser to make sure that the browser does not cache
the previous page.
Browse to http://www.routerlogin.net.
If the computer is set to a static or fixed IP address (this is uncommon), change
it to obtain an IP address automatically from the router.
Note: If you changed the name of your network during the setup process, look
for that network name.
Network key (password) _____________________________________
If necessary to retrieve or update your password, type
http://www.routerlogin.net in a web browser, and log in using the
default user name (admin) and password (password).
Open the software utility that manages your wireless connections on the
wireless device that you want to connect to your router (iPhone, laptop,
computer, or gaming device). This utility scans for all wireless networks in your
area.
•
Internet
WiFi Connection
Router Settings
STATUS GOOD
STATUS Connected
Click here
Network Map
Parental Controls
ReadySHARE
Number of devices 16
Click here
Click here
Download the free genie app from
www.NETGEAR.com/genie.
Easily share media, files, and printers
on the network from your smartphone,
tablet, or laptop.
NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or registered trademarks of
NETGEAR, Inc. and/or its subsidiaries in the United States and/or other countries. Information is subject to change
without notice. © NETGEAR, Inc. All rights reserved.
July 2014
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising