D-Link | DSL-320B ADSL2 Ethernet Modem | Specifications | D-Link DSL-320B ADSL2 Ethernet Modem

Table of Contents
Table of Contents
TABLE OF CONTENTS .................................................................................................2
PACKAGE CONTENTS......................................................................................................3
SYSTEM REQUIREMENTS ................................................................................................3
FEATURES ......................................................................................................................4
HARDWARE OVERVIEW ..................................................................................................5
Connections ..............................................................................................................5
LEDs.........................................................................................................................6
INSTALLATION .............................................................................................................7
SAVE/RESTORE SETTINGS ............................................................................................ 32
FIRMWARE UPDATE ...................................................................................................... 33
DIAGNOSTICS ............................................................................................................... 34
SYSTEM LOG ................................................................................................................ 35
STATUS .......................................................................................................................... 36
DEVICE INFO ................................................................................................................ 36
CONNECTED CLIENTS .................................................................................................. 37
STATISTICS ................................................................................................................... 38
BEFORE YOU BEGIN .......................................................................................................7
INSTALLATION NOTES ....................................................................................................7
DEVICE INSTALLATION ................................................................................................. 11
Power on Modem....................................................................................................12
Factory Reset Button ..............................................................................................12
Network Connections..............................................................................................13
HELP .............................................................................................................................. 39
SETUP.............................................................................................................................14
TECHNICAL SPECIFICATIONS ............................................................................... 44
TROUBLESHOOTING ................................................................................................ 40
NETWORKING BASICS ............................................................................................. 42
CHECK YOUR IP ADDRESS ........................................................................................... 42
STATICALLY ASSIGN AN IP ADDRESS ........................................................................... 43
Web-based Configuration Utility ............................................................................14
QUICK SETUP ...............................................................................................................15
ADSL SETUP ...............................................................................................................21
PPPoE/PPPoA .......................................................................................................22
Static IP Address.....................................................................................................23
Bridge Mode ...........................................................................................................24
LAN SETUP .................................................................................................................25
Use the Modem for DHCP .....................................................................................26
Disable the DHCP Server.......................................................................................26
TIME AND DATE ...........................................................................................................27
PARENTAL CONTROL ....................................................................................................28
ADVANCED ...................................................................................................................29
DNS SETUP .................................................................................................................29
ADVANCED ADSL........................................................................................................30
MAINTENANCE...........................................................................................................31
PASSWORD ...................................................................................................................31
D-Link DSL-320B User Manual
2
Section 1 - Product Overview
•
•
•
•
•
•
Package Contents
DSL-320B ADSL Modem
Power Adapter
CD-ROM with User Manual
One twisted-pair telephone cable used for ADSL connection
One straight-through Ethernet cable
One Quick Installation Guide
Note: Using a power supply with a different voltage rating than the one included
with the DSL-320B will cause damage and void the warranty for this product.
•
•
•
System Requirements
ADSL Internet service
Computer with:
• 200MHz Processor
• 64MB Memory
• CD-ROM Drive
• Ethernet Adapter with TCP/IP Protocol Installed
• Internet Explorer v6 or later, FireFox v1.5, or Safari 1.3 or above
• Windows 2000/XP/Vista
D-Link Click'n Connect Utility
D-Link DSL-320B User Manual
3
Section 1 - Product Overview
11
Features
•
PPP (Point-to-Point Protocol) Security – The Modem supports PAP (Password Authentication Protocol) and CHAP (Challenge Handshake
Authentication Protocol) for PPP connections. The Modem also supports MSCHAP.
•
DHCP Support – Dynamic Host Configuration Protocol automatically and dynamically assigns all LAN IP settings to each host on your
network. This eliminates the need to reconfigure every host whenever changes in network topology occur.
•
TCP/IP (Transfer Control Protocol/Internet Protocol) – The Modem supports TCP/IP protocol, the language used for the Internet. It is
compatible with access servers manufactured by major vendors.
•
ATM (Asynchronous Transfer Mode) – The Modem supports Bridged Ethernet over ATM (RFC1483) and PPP over ATM (RFC 2364).
•
Precise ATM Traffic Shaping – Traffic shaping is a method of controlling the flow rate of ATM data cells. This function helps to establish the
Quality of Service for ATM data transfer.
•
High Performance – Very high rates of data transfer are possible with the Modem. Up to 8 Mbps downstream bit rate using the G.dmt
standard.
•
Telnet Connection – The Telnet enables a network manager to access the Modem’s management software remotely.
•
Easy Installation – The Modem uses a web-based graphical user interface program for convenient management access and easy set up.
Any common web browser software can be used to manage the Modem.
D-Link DSL-320B User Manual
4
Section 1 - Product Overview
•
Hardware Overview
Connections
ADSL Port
Use the ADSL cable to connect
to the your telephone line (RJ-11
port).
Ethernet Port
Use the Ethernet port to connect
the Modem to a computer or an
Ethernet LAN.
D-Link DSL-320B User Manual
Reset Button
To manually reset, depress
button with the power on for at
least seven seconds.
Power Button
Push in to power-on the Modem
Push again to power-off the
Modem.
Power Insert
Use the adapter shipped with the
Modem to connect to power
source.
5
Section 1 - Product Overview
Hardware Overview
LEDs
Power
A steady green light indicates the
unit is powered on. When the device
is powered off this remains dark.
Status
Lights steady green during power on self-test
(POST). Once the connection status has been
settled, the light will blink green. If the indicator
lights steady green after the POST, the system
has failed and the device should be rebooted.
D-Link DSL-320B User Manual
DSL
A steady green light indicates a valid
ADSL connection. This will light after the
ADSL negotiation process has been
settled. A blinking green light indicates
activity on the WAN (ADSL) interface.
LAN
A solid green light indicates a valid link on
startup. This light will blink when there is activity
currently passing through the Ethernet port.
6
Section 2 – Installation
Installation
This section will walk you through the installation process. Placement of the Modem is very important. Do not place the Modem in an enclosed area
such as a closet, cabinet, or in the attic or garage.
Before You Begin
Please read and make sure you understand all the prerequisites for proper installation of your new Modem. Have all the necessary information and
equipment on hand before beginning the installation.
Installation Notes
In order to establish a connection to the Internet it will be necessary to provide information to the Modem that will be stored in its memory. For some
users, only their account information (Username and Password) is required. For others, various parameters that control and define the Internet
connection will be required. You can print out the two pages below and use the tables to list this information. This way you have a hard copy of all
the information needed to setup the Modem. If it is necessary to reconfigure the device, all the necessary information can be easily accessed. Be
sure to keep this information safe and private.
Low Pass Filters
Since ADSL and telephone services share the same copper wiring to carry their respective signals, a filtering mechanism may be necessary to
avoid mutual interference. A low pass filter device can be installed for each telephone that shares the line with the ADSL line. These filters are easy
to install passive devices that connect to the ADSL device and/or telephone using standard telephone cable. Ask your service provider for more
information about the use of low pass filters with your installation.
Operating Systems
The DSL-320B uses an HTML-based web interface for setup and management. The Web configuration manager may be accessed using any
operating system capable of running web browser software, including Windows 98 SE, Windows ME, Windows 2000, Windows XP, and Windows
Vista.
D-Link DSL-320B User Manual
7
Section 2 – Installation
Web Browser
Any common Web browser can be used to configure the Modem using the Web configuration management software. The program is designed to
work best with more recently released browsers such as Opera, Microsoft Internet Explorer® version 6.0, Netscape Navigator® version 6.2.3, or
later versions. The Web browser must have JavaScript enabled. JavaScript is enabled by default on many browsers. Make sure JavaScript has not
been disabled by other software (such as virus protection or web user security packages) that may be running on your computer.
Ethernet Port (NIC Adapter)
Any computer that uses the Modem must be able to connect to it through the Ethernet port on the Modem. This connection is an Ethernet
connection and therefore requires that your computer be equipped with an Ethernet port as well. Most notebook computers are now sold with an
Ethernet port already installed. Likewise, most fully assembled desktop computers come with an Ethernet NIC adapter as standard equipment. If
your computer does not have an Ethernet port, you must install an Ethernet NIC adapter before you can use the Modem. If you must install an
adapter, follow the installation instructions that come with the Ethernet NIC adapter.
Additional Software
It may be necessary to install software on your computer that enables the computer to access the Internet. Additional software must be installed if
you are using the device a simple bridge. For a bridged connection, the information needed to make and maintain the Internet connection is stored
on another computer or gateway device, not in the Modem itself.
If your ADSL service is delivered through a PPPoE or PPPoA connection, the information needed to establish and maintain the Internet connection
can be stored in the Modem. In this case, it is not necessary to install software on your computer. It may however be necessary to change some
settings in the device, including account information used to identify and verify the connection.
All connections to the Internet require a unique global IP address. For bridged connections, the global IP settings must reside in a TCP/IP enabled
device on the LAN side of the bridge, such as a PC, a server, a gateway device such as a Modem or similar firewall hardware. The IP address can
be assigned in a number of ways. Your network service provider will give you instructions about any additional connection software or NIC
configuration that may be required.
D-Link DSL-320B User Manual
8
Section 2 – Installation
Information you will need from your ADSL service
provider
Username
This is the Username used to log on to your ADSL service provider’s network. Your ADSL service provider uses this to identify your account.
Password
This is the Password used, in conjunction with the Username above, to log on to your ADSL service provider’s network. This is used to verify the
identity of your account.
WAN Setting / Connection Type
These settings describe the method your ADSL service provider uses to transport data between the Internet and your computer. Most users will use
the default settings. You may need to specify one of the following WAN Setting and Connection Type configurations (Connection Type settings listed
in parenthesis):
• PPPoE/PPoA (PPPoE LLC, PPPoE VC-Mux, PPPoA LLC or PPPoA VC-Mux)
• Static IP Address (1483 Routed IP LLC or 1483 Routed IP VC-Mux)
• Bridge Mode (1483 Bridged IP LLC or 1483 Bridged IP VC Mux)
Modulation Type
ADSL uses various standardized modulation techniques to transmit data over the allotted signal frequencies. Some users may need to change the
type of modulation used for their service. The default DSL modulation (Autosense) used for the Modem automatically detects all types of ADSL,
ADSL2, and ADSL2+ modulation.
Security Protocol
This is the method your ADSL service provider will use to verify your Username and Password when you log on to their network. Your Modem
supports the PAP and CHAP protocols.
D-Link DSL-320B User Manual
9
Section 2 – Installation
VPI
Most users will not be required to change this setting. The Virtual Path Identifier (VPI) is used in conjunction with the Virtual Channel Identifier (VCI)
to identify the data path between your ADSL service provider’s network and your computer. If you are setting up the Modem for multiple virtual
connections, you will need to configure the VPI and VCI as instructed by your ADSL service provider for the additional connections. This setting can
be changed in the WAN Settings window of the web management interface.
VCI
Most users will not be required to change this setting. The Virtual Channel Identifier (VCI) used in conjunction with the VPI to identify the data path
between your ADSL service provider’s network and your computer. If you are setting up the Modem for multiple virtual connections, you will need to
configure the VPI and VCI as instructed by your ADSL service provider for the additional connections. This setting can be changed in the WAN
Settings window of the web management interface.
Information you will need about DSL-320B
Username
This is the Username needed access the Modem’s management interface. When you attempt to connect to the device through a web browser you
will be prompted to enter this Username. The default Username for the Modem is “admin.” The user cannot change this.
Password
This is the Password you will be prompted to enter when you access the Modem’s management interface. The default Password is “admin.” The
user may change this.
LAN IP addresses for the DSL-320B
This is the IP address you will enter into the Address field of your web browser to access the Modem’s configuration graphical user interface (GUI)
using a web browser. The default IP address is 192.168.1.1. This may be changed to suit any IP address scheme the user desires. This address will
be the base IP address used for DHCP service on the LAN when DHCP is enabled.
LAN Subnet Mask for the DSL-320B
This is the subnet mask used by the DSL-320B, and will be used throughout your LAN. The default subnet mask is 255.255.255.0. This can be
changed later.
D-Link DSL-320B User Manual
10
Section 2 – Installation
Information you will need about your LAN or computer
:
Ethernet NIC
If your computer has an Ethernet NIC, you can connect the DSL-320B to this Ethernet port using an Ethernet cable. You can also use the Ethernet
ports on the DSL-320B to connect to other computer or Ethernet devices.
DHCP Client status
Your DSL-320B ADSL Modem is configured, by default, to be a DHCP server. This means that it can assign an IP address, subnet mask, and a
default gateway address to computers on your LAN. The default range of IP addresses the DSL-320B will assign are from 192.168.1.2 to
192.168.1.254. Your computer (or computers) needs to be configured to obtain an IP address automatically (that is, they need to be configured as
DHCP clients.)
It is recommended that your collect and record this information here, or in some other secure place, in case you have to re-configure your ADSL
connection in the future.
Once you have the above information, you are ready to setup and configure your DSL-320B ADSL Modem.
Device Installation
The DSL-320B connects two separate physical interfaces, an ADSL (WAN) and an Ethernet (LAN) interface. Place the Modem in a location where it
can be connected to the various devices as well as to a power source. The Modem should not be located where it will be exposed to moisture or
excessive heat. Make sure the cables and power cord are placed safely out of the way so they do not create a tripping hazard. As with any electrical
appliance, observe common sense safety procedures.
The Modem can be placed on a shelf or desktop, ideally you should be able to see the LED indicators on the front if you need to view them for
troubleshooting.
D-Link DSL-320B User Manual
11
Section 2 – Installation
Power on Modem
The Modem must be used with the power adapter included with the device.
1. Insert the AC Power Adapter cord into the power receptacle located on the rear panel of the Modem and plug the adapter into a suitable nearby
power source.
2. Depress the Power button into the on position. You should see the Power LED indicator light up and remain lit. The Status LED should light solid
green and begin to blink after a few seconds.
3. If the Ethernet port is connected to a working device, check the Ethernet Link/Act LED indicators to make sure the connection is valid. The
Modem will attempt to establish the ADSL connection, if the ADSL line is connected and the Modem is properly configured this should light up
after several seconds. If this is the first time installing the device, some settings may need to be changed before the Modem can establish a
connection.
Factory Reset Button
The Modem may be reset to the original factory default settings by using a ballpoint or paperclip to gently push down the reset button in the
following sequence:
1. Press and hold the reset button while the device is powered off.
2. Turn on the power.
3. Wait for 5~8 seconds and then release the reset button.
Remember that this will wipe out any settings stored in flash memory including user account information and LAN IP settings. The device settings
will be restored to the factory default IP address 192.168.1.1 and the subnet mask is 255.255.255.0, the default management Username is “admin”
and the default Password is “admin.”
D-Link DSL-320B User Manual
12
Section 2 – Installation
Network Connections
Connect ADSL Line
Use the ADSL cable included with the Modem to connect it to a telephone wall socket or receptacle. Plug one end of the cable into the ADSL port
(RJ-11 receptacle) on the rear panel of the Modem and insert the other end into the RJ-11 wall socket. If you are using a low pass filter device,
follow the instructions included with the device or given to you by your service provider. The ADSL connection represents the WAN interface, the
connection to the Internet. It is the physical link to the service provider’s network backbone and ultimately to the Internet.
Connect Modem to Ethernet
The Modem may be connected to a single computer or Ethernet device through the 10BASE-TX Ethernet port on the rear panel. Any connection to
an Ethernet concentrating device such as a switch or hub must operate at a speed of 10/100 Mbps only. When connecting the Modem to any
Ethernet device that is capable of operating at speeds higher than 10Mbps, be sure that the device has auto-negotiation (NWay) enabled for the
connecting port. Use standard twisted-pair cable with RJ-45 connectors. The RJ-45 port on the Modem is a crossed port (MDI-X). Follow standard
Ethernet guidelines when deciding what type of cable to use to make this connection. When connecting the Modem directly to a PC or server use a
normal straight-through cable. You should use a crossed cable when connecting the Modem to a normal (MDI-X) port on a switch or hub. Use a
normal straight-through cable when connecting it to an uplink (MDI-II) port on a hub or switch. The rules governing Ethernet cable lengths apply to
the LAN to Modem connection. Be sure that the cable connecting the LAN to the Modem does not exceed 100 meters.
Hub or Switch to Modem Connection
Connect the Modem to an uplink port (MDI-II) on an Ethernet hub or switch with a straight-through cable. If you wish to reserve the uplink port on
the switch or hub for another device, connect to any on the other MDI-X ports (1x, 2x, etc.) with a crossed cable.
Computer to Modem Connection
You can connect the Modem directly to a 10/100BASE-TX Ethernet adapter card (NIC) installed on a PC using the Ethernet cable provided.
D-Link DSL-320B User Manual
13
Section 3 – Configuration
Setup
This section will show you how to set up and configure your new D-Link Modem using the Web-based configuration utility.
Web-based Configuration Utility
Connect to the Modem
To configure the WAN connection used by the Modem it is first necessary to communicate with the Modem through its management interface, which
is HTML-based and can be accessed using a web browser. The easiest way to make sure your computer has the correct IP settings is to configure
it to use the DHCP server in the Modem. The next section describes how to change the IP configuration for a computer running a Windows
operating system to be a DHCP client.
To access the configuration utility, open a web-browser such as Internet
Explorer and enter the IP address of the Modem (192.168.1.1).
Type “admin” for the User Name and “admin” in the Password field. If
you get a Page Cannot be Displayed error, please refer to the
Troubleshooting section for assistance.
D-Link DSL-320B User Manual
14
Section 3 – Configuration
Quick Setup
This chapter is concerned with using your computer to configure the WAN connection. The following chapter describes the various windows used to
configure and monitor the Modem including how to change IP settings and DHCP server setup.
QUICK SETUP
Click the Setup Wizard link at the top of the window of the Modem’s
opening page to launch a series of setup windows.
Alternatively, you can tick the Manual Setup check box and click the
desired setting option radio button in the middle of the window. The
manual ADSL connection setup is described later in this manual.
The Modem allows you to change the Web manager’s language settings
using the drop-down menu on the left side of the window. The choices are:
English, Spanish, French, Italian, and German. Please note that in some
markets, only English is supported at this time.
D-Link DSL-320B User Manual
15
Section 3 – Configuration
QUICK SETUP – OPENING WINDOW
The first window of the Setup Wizard lists the basic steps in the process.
These steps are as follows:
1. Change the Modem password.
2. Configure the connection to the Internet.
3. Save the new configuration settings and reboot the system.
QUICK SETUP – CHANGE YOUR MODEM PASSWORD
This window of the Setup Wizard is used to change the Modem password.
D-Link recommends to help secure your network, the user change the
Current Password from the factory default “admin.” The New Password
should be between 1 and 16 alphanumeric characters. Once you have
filled out the fields in this window, including re-typing the new password in
the Confirm Password field, click the Next button to continue.
If you do not want to change the password, click the Skip button to
proceed to the next step.
D-Link DSL-320B User Manual
16
Section 3 – Configuration
QUICK SETUP – SELECT THE INTERNET CONNECTION TYPE
Now use the drop-down menus to select the Country, ISP Provider, and
Connection Type used for the Internet connection, and enter VPI and VCI
values if applicable. Your ISP has given this information to you—any
information that is not required for your provider will automatically be
grayed out in this window and subsequent Quick Setup windows.
The Connection Type options are 1483 Bridged IP LLC, 1483 Bridged IP
VC-Mux, 1483 Routed IP LLC, 1483 Routed IP VC-Mux, PPPoE LLC,
PPPoE VC-Mux, PPPoA LLC, and PPPoA VC-Mux.
Click the Next button when you are finished to proceed to the next Setup
Wizard window.
QUICK SETUP – SELECT THE INTERNET CONNECTION TYPE
If the following Setup Wizard window appears, please select the
connection type used by your ISP and then click the Next button. Most
users, however, will be sent directly to a Setup Wizard window for their
specific Internet connection type based on the information entered in the
previous Setup Wizard window.
D-Link DSL-320B User Manual
17
Section 3 – Configuration
QUICK SETUP – PPPOE/PPPOA CONFIGURATION
Type in the User Name and Password used to identify and verify your
account to the ISP. If you are instructed to change the VPI or VCI number,
type in the correct setting in the available entry fields. Most users will not
need to change these settings. The Internet connection cannot function if
these values are incorrect.
Some users may have to adjust the Connection Type from the drop-down
menu at the bottom of this Setup Wizard window. The available
connection and encapsulation types are PPPoE LLC, PPoE VC-Mux,
PPPoA LLC, and PPPoA VC-Mux.
Click Next to go to the last Setup Wizard window.
D-Link DSL-320B User Manual
18
Section 3 – Configuration
QUICK SETUP – STATIC IP CONFIGURATION
Enter values for VPI, VCI, IP Address, Subnet Mask, Default Gateway IP
address, Preferred DNS Server IP address, and Alternate DNS Server IP
address as instructed by your ISP. The Internet connection cannot
function if these values are incorrect.
Select the specific Connection Type from the drop-down menu. The
available connection and encapsulation types are 1483 Routed IP LLC
and 1483 Routed IP VC-Mux.
Click Next to go to the last Setup Wizard window.
QUICK SETUP – BRIDGE MODE CONFIGURATION
If you are instructed to change the VPI or VCI numbers, type in the correct
setting in the available entry fields. The Internet connection cannot
function if these values are incorrect.
Select the specific Connection Type from the drop-down menu. The
available connection and encapsulation types are 1483 Bridged IP LLC
and 1483 Bridged IP VC-Mux.
Click Next to go to the last Setup Wizard window.
D-Link DSL-320B User Manual
19
Section 3 – Configuration
QUICK SETUP – FINISH & RESTART CONFIRMATION
Finally you can confirm that the setup process is completed. If you are
satisfied that you have entered all the necessary information correctly,
click the Restart button to save the new configuration settings and restart
the Modem. If you need to change settings from a previous window, click
the Back button.
QUICK SETUP – REBOOT CONFIRMATION DIALOG
Click the OK button to proceed with the Modem reboot.
QUICK SETUP – REBOOT TIME INDICATOR
The following window opens to indicate the amount of time it will take to
reboot the Modem.
QUICK SETUP – REBOOT CONFIRMATION DIALOG
Click OK to continue.
D-Link DSL-320B User Manual
20
Section 3 – Configuration
ADSL Setup
To access the ADSL Setup window, simply login to the Modem or click either ADSL Setup in the Setup directory or Setup on the tool bar at the top
of the Web manager window. Tick the Manual Setup check box located next to the Setup Wizard button to display the following window:
To configure the Modem’s basic configuration settings without running the
Setup Wizard, you can access the windows used to configure ADSL
Setup, LAN Setup, Time and Date, and Parental Control settings directly
from the Setup directory.
To access the ADSL Setup windows for Manual ADSL Connection Setup
for PPPoE/PPPoA, Static IP Address, and Bridge Mode, click on the
ADSL Setup link button on the left side of the first window that appears
when you successfully access the web manager.
The Modem allows you to change the Web manager’s language settings
using the drop-down menu on the left side of the window. The choices are:
English, Spanish, French, Italian, and German. Please note that in some
markets, only English is supported at this time.
Click the PPPoE/PPPoA radio button to access the first Manual ADSL
Connection Setup window:
D-Link DSL-320B User Manual
21
Section 3 – Configuration
PPPoE/PPPoA
To configure a PPPoE or PPPoA type WAN connection, follow these
steps:
1. Type the Username and Password used for your ADSL account. A
typical User Name will be in the form “user1234@isp.co.uk.” The
Password may be assigned to you by your ISP or you may have
selected it when you set up the account with your ISP. The Service
Name field is used for the name of your Internet Service Provider.
This is optional.
2. Choose the Connection Type from the drop-down menu. This
defines both the connection protocol and encapsulation method
used for your ADSL service. The available options are PPPoE LLC,
PPPoE VC-Mux, PPPoA LLC and PPPoA VC-Mux. If you have not
been provided specific information for the Connection Type setting,
leave the default setting.
3. Leave the MTU value at the default setting unless you have
specific reasons to change this.
4. Some users will want to set an Idle Time Out. This is an age-out
value, in minutes, before the Modem times out.
5. If you are instructed to change the VPI or VCI values, type in the
values assigned for your account.
6. When you are satisfied that all the WAN settings are configured
correctly, click the Apply Settings button. This will save the
settings and reboot the Modem to let your changes take effect.
7. Upon restarting, the Modem should automatically establish the
WAN connection. If it does not, click the Connect button at the
bottom of this window.
D-Link DSL-320B User Manual
22
Section 3 – Configuration
Static IP Address
When the Modem is configured to use Static IP Address assignment for
the WAN connection, you must manually assign a global IP Address,
Subnet Mask, and Default Gateway IP address used for the WAN
connection.
.
To configure a Static IP Address WAN connection, follow these steps:
1. Change the IP Address, Subnet Mask, and Default Gateway as
instructed by your ISP. These are the global IP settings for the
WAN interface. This is the “visible” IP address of your account.
Your ISP should have provided these IP settings to you. If your ISP
also asks you to change DNS server IP addresses, enter the
Preferred DNS Server and Alternate DNS Server information
manually.
2. Choose the Connection Type from the drop-down menu. This
defines both the connection protocol and encapsulation method
used for your ADSL service. The available options are 1483
Routed IP LLC and 1483 Routed IP VC-Mux. If you have not been
provided specific information for this setting, leave the default
setting.
3. If you are instructed to change the VPI or VCI values, type in the
values assigned for your account.
4. When you are satisfied that all the WAN settings are configured
correctly, click the Apply Settings button. This will save the
settings and reboot the Modem to let your changes take effect.
5. Upon restarting, the Modem should automatically establish the
WAN connection.
D-Link DSL-320B User Manual
23
Section 3 – Configuration
Bridge Mode
For Bridged connections it will be necessary for most users to install
additional software on any computer that will use the Modem for Internet
access. The additional software is used for the purpose of identifying
and verifying your account, and then granting Internet access to the
computer requesting the connection. The connection software requires
the user to enter the User Name and Password for the ISP account. This
information is stored on the computer, not in the Modem.
.
To configure a Static IP Address WAN connection, follow these steps:
1. Choose the Connection Type from the drop-down menu. This
defines both the connection protocol and encapsulation method
used for your ADSL service. The available options are 1483
Bridged IP LLC and 1483 Bridged IP VC-Mux. If you have not
been provided specific information for this setting, leave the
default setting.
2. If you are instructed to change the VPI or VCI values, type in the
values assigned for your account.
3. When you are satisfied that all the WAN settings are configured
correctly, click the Apply Settings button. This will save the
settings and reboot the Modem to let your changes take effect.
4. Upon restarting, the Modem should automatically establish the
WAN connection.
D-Link DSL-320B User Manual
24
Section 3 – Configuration
LAN Setup
To access the LAN Setup window, click the LAN Setup button in the Setup directory.
You can configure the LAN IP address to suit your preference. Many
users will find it convenient to use the default settings together with
DHCP service to manage the IP settings for their private network. The IP
address of the Modem is the base address used for DHCP. In order to
use the Modem for DHCP on your LAN, the IP address pool used for
DHCP must be compatible with the IP address of the Modem. The IP
addresses available in the DHCP IP address pool will change
automatically if you change the IP address of the Modem. See the next
section for information on DHCP setup.
To change the LAN Modem IP Address or Subnet Mask, type in the
desired values in the Modem Settings section and click the Apply
Settings button. Your web browser should automatically be redirected
to the new IP address. You will be asked to login again to the Modem’s
web manager.
The DHCP server is enabled by default for the Modem’s Ethernet LAN
interface. DHCP service will supply IP settings to workstations
configured to automatically obtain IP settings that are connected to the
Modem though the Ethernet port. When the Modem is used for DHCP it
becomes the default gateway for DHCP client connected to it. Keep in
mind that if you change the IP address of the Modem the range of IP
addresses in the pool used for DHCP on the LAN will also be changed.
The IP address pool can be up to 253 IP addresses.
There are two options for DHCP service:
• You can use the Modem as a DHCP server for your LAN.
• You can disable DHCP service and manually configure IP
settings for workstations.
D-Link DSL-320B User Manual
25
Section 3 – Configuration
You may also configure DNS settings when using the Modem in DHCP mode (Advanced > DNS Setup). When “Obtain DNS server address
automatically“ is clicked under DNS Server Configuration on the DNS Setup window, the Modem will automatically relay DNS settings to properly
configured DHCP clients. To manually enter DNS IP addresses, click the “Use the following DNS server addresses“ radio button and type in a
Preferred DNS Server and Alternate DNS Server in the fields provided. The manually configured DNS settings will be supplied to clients that are
configured to request them from the Modem.
Follow the instructions below according to which of the above DHCP options you want to use. When you have configured DHCP as you want, click
the Apply Settings button to commit the new settings.
Use the Modem for DHCP
To use the built-in DHCP server, tick the Enable DHCP Server check box in the DHCP Server Settings (Optional) section if it is not already selected.
The IP address pool settings can be adjusted. The DHCP IP Address Range starts with the lowest available IP address (default = 192.168.1.2). If
you change the IP address of the Modem this will change automatically to be 1 more that the IP address of the Modem. The DHCP IP Address
Range ends with the highest IP address number in the pool. Type in the DHCP Lease Time in the entry field provided. This is the amount of time in
seconds that a workstation is allowed to reserve an IP address in the pool if the workstation is disconnected from the network or powered off.
Disable the DHCP Server
To disable DHCP, deselect the Enable DHCP Server check box in the DHCP Server Settings (Optional) section and click the Apply Settings button.
Choosing this option will gray out most of the setting options on this window and require that workstations on the local network be configured
manually or use another DHCP server to obtain IP settings.
If you configure IP settings manually, make sure to use IP addresses in the subnet of the Modem. You will need to use the Modem’s IP address as
the Default Gateway for the workstation in order to provide Internet access.
D-Link DSL-320B User Manual
26
Section 3 – Configuration
Time and Date
To access the Time and Date window, click the Time and Date button in the Setup directory.
The Modem allows you to configure, update, and maintain the correct
time on the internal clock.
To configure system time on the Modem, click the Copy Your
Computer’s Time Settings button, or set the time and date manually
by using the Date and Time drop-down menus. When you are finished,
click the Apply Settings button to set the system time and date
information.
D-Link DSL-320B User Manual
27
Section 3 – Configuration
Parental Control
To access the Parental Control window, click the Parental Control button in the Setup directory.
Use this window to deny access to specified websites and to set Internet
access time periods.
URL or Uniform Resource Locator is a specially formatted text string that
uniquely defines an Internet website. This window will allow users to block
computers on the LAN from accessing certain URLs. This may be
accomplished by simply entering the URL to be blocked in the Website
field.
To configure this window for URL blocking, enter the website’s address
into the Website field, use the radio buttons to click the desired Day(s),
either All Week or Select Day(s) (in which case you must tick the
checkboxes for the desired individual days of the week), select the
desired Start Time and End Time or tick the All Day – 24 hrs checkbox,
and then click the Block Website button. Configured URL blocking
entries are displayed in the table in the middle of the window. To remove a
Blocked URL entry in the table, tick the Remove check box and then click
the Remove Selected button. To modify a table entry, click the
corresponding Edit hyperlink, make the desired changes, and then click
the Block Website button.
This window also enables you to determine when Internet access is
granted by using the settings in the Internet Access Time Restrictions
section of this window. Configure Time and days of the week and then use
the drop-down menu to toggle the Allow/Deny setting for each time period.
Clicking the Apply Settings button will allow your setting to take effect.
D-Link DSL-320B User Manual
28
Section 3 – Configuration
Advanced
This chapter include the more advanced features used for network management and security.
DNS Setup
To access the DNS Setup window, click the DNS Setup button in the Advanced directory.
If you have not been given specific DNS server IP addresses or if the
Modem is not pre-configured with DNS server information, select the
“Obtain DNS server address automatically” option. Auto discovery DNS
instructs the Modem to automatically obtain the DNS IP address from the
ISP through DHCP. If your WAN connection uses a Static IP address, auto
discovery for DNS cannot be used.
If you have DNS IP addresses provided by your ISP, click the “Use the
following DNS server addresses” radio button and enter these IP
addresses in the available entry fields for the Preferred DNS Server and
the Alternative DNS Server. When you have configured the DNS settings
as desired, click the Apply Settings button and then click the Reboot
button on the left panel to let your changes take effect.
D-Link DSL-320B User Manual
29
Section 3 – Configuration
Advanced ADSL
To access the Advanced ADSL window, click the Advanced ADSL button in the Advanced directory.
This window allows the user to set the configuration for ADSL protocols.
For most ADSL accounts the default settings Autosense will work. This
configuration works with all ADSL implementations. If you have been
given instructions to change the Modulation method used, select the
desired option from the Modulation Type drop-down menu and click the
Apply Settings button. Click the Reboot button on the left panel to let
your changes take effect.
Leave the Capability setting at the bottom of the window unchanged
unless otherwise instructed by your ISP. Both Bitswap Enable and
Seemless Rate Adaption (SRA) Enable deal with tests that determine the
line condition between your Modem and the ISP’s Central office.
D-Link DSL-320B User Manual
30
Section 3 – Configuration
Maintenance
The Maintenance directory features an array of options designed to help you get the most out of your Modem.
Password
To access the Password window, click the Settings button in the Maintenance directory.
To change the Administrator’s password, type the Current Password in
the first field, the New Password in the second field, and enter the
password again in the Confirm Password field to be certain you have
typed it correctly. Click the Apply Settings button and then click the
Reboot button on the left panel to let your changes take effect. The
system User Name remains “admin,” this cannot be changed using the
Web manager interface.
D-Link DSL-320B User Manual
31
Section 3 – Configuration
Save/Restore Settings
To access the Save/Restore Settings window, click the Save/Restore Settings button in the Maintenance directory.
Once you have configured the Modem to your satisfaction, it is a good
idea to back up the configuration file to your computer. To save the current
configuration settings to your computer, click the Save button. You will be
prompted to select a location on your computer to put the file. The file type
is bin and may be named anything you wish.
To load a previously saved configuration file, click the Browse button and
locate the file on your computer. Click the Upload Settings button to load
the settings from your local hard drive. Confirm that you want to load the
file when prompted. The Modem will reboot and begin operating with the
configuration settings that have just been loaded.
To reset the Modem to its factory default settings, click the Restore
Device button. You will be prompted to confirm your decision to reset the
Modem. The Modem will reboot with the factory default settings including
IP settings (192.168.1.1) and Administrator password (admin).
D-Link DSL-320B User Manual
32
Section 3 – Configuration
Firmware Update
To access the Firmware Update window, click the Firmware Update button in the Maintenance directory.
Use this window to load the latest firmware for the device. Note that the
device configuration settings may return to the factory default settings,
so make sure you save the configuration settings with the Save/Restore
Settings window described on the previous page.
To upgrade firmware, type in the name and path of the file or click on the
Browse button to search for the file. Click the Update Firmware button
to begin copying the file. The file will load and restart the Modem
automatically.
To save your current configuration file to your computer, click the
Backup Now button. A File Download dialog box will open. Click the
Save button and then designate the location for the configuration file in
the Save As window that immediately opens. The default location is
your desktop.
Note
Performing a Firmware Upgrade can sometimes change the
configuration settings. Be sure to backup the Modem’s configuration
settings before upgrading the firmware.
D-Link DSL-320B User Manual
33
Section 3 – Configuration
Diagnostics
To access the Diagnostic window, click the Diagnostics button in the Maintenance directory.
This window is used to test connectivity of the Modem. A Ping test may be
done through the local or external interface to test connectivity to known IP
addresses. The diagnostics feature executes a series of tests of your
system software and hardware connections. Use this window when
working with your ISP to troubleshoot problems.
D-Link DSL-320B User Manual
34
Section 3 – Configuration
System Log
To access the System Log window, click the System Log button in the Maintenance directory.
The system log allows you to configure local and remote logging, and to
view the logs that have been created.
To generate a system log, tick the Log check box. Select the Log Level
and Display Level from the pull-down menus. The levels available are the
same for each type of level: Emergency, Alert, Critical, Error, Warning,
Notice, Informational and Debugging. Use the Mode drop-down menu to
select Local, Remote, or Both. Click the Apply Settings button and then
click the Reboot button on the left panel to allow your new settings to
take effect.
D-Link DSL-320B User Manual
35
Section 3 – Configuration
Status
Use the various read-only windows to view system information and monitor performance.
Device Info
To access the Device Info window, click the Device Info button in the Status directory.
Use this window to quickly view basic current information about the LAN
and WAN interfaces and device information including Firmware Version
and MAC address.
D-Link DSL-320B User Manual
36
Section 3 – Configuration
Connected Clients
To access the Connected Clients window, click the Connected Clients button in the Status directory.
The Connected LAN Clients list displays active DHCP clients when the
Modem is acting as a DHCP server.
D-Link DSL-320B User Manual
37
Section 3 – Configuration
Statistics
To access the Statistics window, click the Statistics button in the Status directory.
Use this window to monitor traffic on the Ethernet or ADSL connection.
This window also displays information concerning ADSL status.
D-Link DSL-320B User Manual
38
Section 3 – Configuration
Help
To access the Help window, click the Help directory.
D-Link DSL-320B User Manual
39
Appendix A – Troubleshooting
Troubleshooting
This chapter provides solutions to problems that might occur during the installation and operation of the DSL-320B. Read the following descriptions
if you are having problems. (The examples below are illustrated in Windows® XP. If you have a different operating system, the screenshots on your
computer will look similar to the following examples.)
1.
How do I configure my DSL-320B Modem without the CD-ROM?
•
•
•
•
Note:
2.
Please refer to the next section “Networking Basics” to check your PC’s IP configuration if you can’t see the login windows.
How do I reset my Modem to the factory default settings?
•
•
•
Note:
3.
Connect your PC to the Modem using an Ethernet cable.
Open a web browser and enter the address http://192.168.1.1
The default username is ‘admin’ and the default password is ‘admin’.
If you have changed the password and cannot remember it, you will need to reset the Modem to the factory default setting (see question 2),
which will set the password back to ‘admin’.
Ensure the Modem is powered on.
Press and hold the reset button on the back of the device for approximately 5 to 8 seconds.
This process should take around 1 to 2 minutes.
Resetting the Modem to the factory default settings will erase the current configuration settings. To reconfigure your settings, login to the Modem as
outlined in question 1, then run the Quick Setup wizard.
What can I do if my Modem is not working correctly?
There are a few quick steps you can take to try and resolve any issues:
• Follow the directions in Question 2 to reset the Modem.
• Check that all the cables are firmly connected at both ends.
• Check the LEDs on the front of the Modem. The Power indicator should be on, the Status indicator should flash, and the DSL and LAN
indicators should be on as well.
D-Link DSL-320B User Manual
40
Appendix A – Troubleshooting
•
4.
Please ensure that the settings in the Web-based configuration manager, e.g. ISP username and password, are the same as the settings
that have been provided by your ISP.
Why can’t I get an Internet connection?
For ADSL ISP users, please contact your ISP to make sure the service has been enabled/connected by your ISP and that your ISP username and
password are correct.
5.
What can I do if my Modem can’t be detected by running the installation CD?
•
•
•
•
Note:
Ensure the Modem is powered on.
Check that all the cables are firmly connected at both ends and all LEDs work correctly.
Ensure only one network interface card on your PC is activated.
Click on Start > Control Panel > Security Center to disable the firewall.
There is a potential security issue if the firewall is disabled on your PC. Please remember to turn it back on once you have finished the whole
installation procedure. This will enable you to be able to surf the Internet without any problem.
D-Link DSL-320B User Manual
41
Appendix B - Networking Basics
Networking Basics
Check Your IP Address
After you install your new D-Link adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e. wireless
Modem) automatically. To verify your IP address, please follow the steps below.
Click on Start > Run. In the run box type cmd and click on the OK.
At the prompt, type ipconfig and press Enter.
This will display the IP address, subnet mask, and the default gateway
of your adapter.
If the address is 0.0.0.0, check your adapter installation, security
settings, and the settings on your Modem. Some firewall software
programs may block a DHCP request on newly installed adapters.
If you are connecting to a wireless network at a hotspot (e.g. hotel,
coffee shop, airport), please contact an employee or administrator to
verify their wireless network settings.
D-Link DSL-320B User Manual
42
Appendix B - Networking Basics
Statically Assign An IP Address
If you are not using a DHCP capable gateway/Modem, or you need to assign a static IP address, please follow the steps below:
Step 1
Windows® XP - Click on Start > Control Panel > Network Connections.
Windows® 2000 - From the desktop, right-click on the My Network Places > Properties.
Step 2
Right-click on the Local Area Connection which represents your D-Link network adapter and select Properties.
Step 3
Highlight Internet Protocol (TCP/IP) and click on the Properties.
Step 4
Click on the Use the following IP address and enter an IP address that
is on the same subnet as your network or the LAN IP address on your
Modem.
Example: If the Modem’s LAN IP address is 192.168.1.1, make your IP
address 192.168.1.X where X is a number between 2 and 254. Make
sure that the number you choose is not in use on the network. Set
Default Gateway the same as the LAN IP address of your Modem
(192.168.1.1).
Set Primary DNS the same as the LAN IP address of your Modem
(192.168.1.1). The Secondary DNS is not needed or you may enter a
DNS server from your ISP.
Step 5
Click on the OK twice to save your settings.
D-Link DSL-320B User Manual
43
Appendix C – Technical Specifications
Technical Specifications
Data Transfer Rate
ADSL Standards
•
•
•
•
ANSI T1.413 Issue 2
ITU G.992.1 (G.dmt) AnnexA
ITU G.992.2 (G.lite) Annex A
ITU G.994.1 (G.hs)
•
•
•
ADSL2 Standards
•
•
•
ITU G.992.3 (G.dmt.bis) Annex A
ITU G.992.4 (G.lite.bis) Annex A
ADSL2+ Standards
•
•
•
•
•
•
•
Media Interface
ITU G.992.5 Annex A
Protocols
TCP/UDP
ARP
RARP
ICMP
RFC1334 PAP
RFC1483/2684
Multiprotocol
Encapsulation over ATM
Adaptation Layer 5 (AAL5)
D-Link DSL-320B User Manual
G.dmt full rate downstream: up to 8 Mbps / upstream: up to 1
Mbps
G.lite: ADSL downstream up to 1.5 Mbps / upstream up to 512
Kbps
G.dmt.bis full rate downstream: up to 12 Mbps / upstream: up
to 12 Mbps
ADSL full rate downstream: up to 24 Mbps / upstream: up to 1
Mbps
•
•
•
•
•
•
RFC1661 Point to Point
Protocol
RFC1994 CHAP
RFC2131 DHCP Client /
DHCP Server
RFC2364 PPP over ATM
RFC2516 PPP over
Ethernet
•
ADSL interface: RJ-11 connector for connection to 24/26
AWG twisted pair telephone line
LAN interface: one RJ-45 port for 10/100BASE-T Ethernet
connection
44
Download PDF