Si4836-A10 - Silicon Labs

Si4836-A10 - Silicon Labs
Si 4 8 3 6 - A10
B R O A D C A S T M E CH A N I C A L TU N I N G A M / F M / S W R ADIO R E C E IV E R
Features







Worldwide FM band support
(64–109 MHz)
Worldwide AM band support
(504–1750 kHz)
SW band support
(2.3–28.5 MHz)
No manual alignment necessary
Stereo audio output
Selectable support AM/FM/SW
regional bands
Enhanced FM/SW band coverage










Station and stereo LED indicators
China TV channels audio carrier
reception in FM band
Automatic frequency control (AFC)
Integrated LDO regulator
2.0 to 3.6 V supply voltage
Wide range of ferrite loop sticks and
air loop antennas supported
16-pin SOIC
RoHS-compliant
Bass/Treble control
EN55020 compliant
Ordering Information:
See page 14.
Applications
Pin Assignments
Table and portable radios
Mini/micro systems
 CD/DVD players
 Boom boxes
Modules
Clock radios
 Mini HiFi
 Entertainment systems




Si4836-A10 (SOIC)
Description
The Si4836 is the high performance receiver function from antenna input to audio
output. The Si4836 extends Silicon Laboratories multi-band tuner family, and
further increases the ease and attractiveness of design radio reception to audio
devices through small size and board area, minimum component count, and
superior, proven performance. Si4836 enhances the FM and SW band coverage,
further supports China TV channels audio reception in FM band. The Si4836
removes any requirements for manually tuning components during the
manufacturing process. The receiver has very low power consumption, runs off
two AAA batteries, and delivers the performance benefits of digital tuning to the
analog radio market.
Functional Block Diagram
Si4836
ADC
AMI
AM
ANT
RFGND
LNA
ADC
FM
ANT
FMI
DAC
LOUT
DAC
ROUT
DSP
LOUT
1
16
ROUT
TUNE1
2
15
GND
TUNE2
3
14
VDD
BAND
4
13
XTALI
NC
5
12
XTALO
FMI
6
11
STATION
RFGND
7
10
STEREO/LNA_EN
AMI
8
9
RST
This product, its features, and/or its
architecture is covered by one or more of
the following patents, as well as other
patents, pending and issued, both
foreign and domestic: 7,127,217;
7,272,373;
7,272,375;
7,321,324;
7,355,476;
7,426,376;
7,471,940;
7,339,503; 7,339,504.
AGC
0/90
TUNE1/2
ADC
CONTROL INTERFACE
BAND
Stereo
REG
XTAL
OSC
Rev. 1.0 5/13
RST
VDD
Tone
2.0~3.6V
AFC
Station
XTALI
Copyright © 2013 by Silicon Laboratories
Si4836-A10
This information applies to a product under development. Its characteristics and specifications are subject to change without notice.
Si4836-A10
2
Rev. 1.0
Si4836-A10
TABLE O F C ONTENTS
Section
Page
1. Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
2. Typical Application Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
3. Bill of Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4. Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.1. Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.2. FM Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
4.3. AM Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
4.4. SW Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.5. Frequency Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.6. Band Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
4.7. Bass and Treble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
4.8. Reset, Powerup, and Powerdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5. Pin Descriptions: Si4836-A10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
6. Ordering Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
7. Package Outline: Si4836-A10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
8. PCB Land Pattern: Si4836-A10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
9. Top Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
9.1. Si4836-A10 Top Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
9.2. Top Marking Explanation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
10. Additional Reference Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Document Change List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Rev. 1.0
3
Si4836-A10
1. Electrical Specifications
Table 1. Recommended Operating Conditions1,2
Parameter
Symbol
Min
Typ
Max
Unit
VDD
2
—
3.6
V
VDDRISE
10
—
—
µs
TA
–15
25
85
°C
Supply Voltage3
Power Supply Powerup Rise Time
Ambient Temperature Range
Test Condition
Note:
1. Typical values in the data sheet apply at VDD = 3.3 V and 25 °C unless otherwise stated.
2. All minimum and maximum specifications in the data sheet apply across the recommended operating conditions for
minimum VDD = 2.7 V.
3. Operation at minimum VDD is guaranteed by characterization when VDD voltage is ramped down to 2.0 V. Part
initialization may become unresponsive below 2.3 V.
Table 2. DC Characteristics
(VDD = 2.7 to 3.6 V, TA = –15 to 85 °C)
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
IFM
—
20.0
—
mA
IAM
—
19.0
—
mA
IDDPD
—
10
—
µA
FM Mode
Supply Current*
AM/SW Mode
Supply Current*
Supplies and Interface
VDD Powerdown Current
*Note: Specifications are guaranteed by characterization.
4
Rev. 1.0
Si4836-A10
Table 3. Reset Timing Characteristics
(VDD = 2.7 to 3.6 V, TA = –15 to 85 °C)
Parameter
Symbol
Min
Typ
Max
Unit
RSTB Pulse Width
tPRST
100
—
—
µs
VDD Valid Time Before RSTB Rises
tSRST
100
—
—
µs
RSTB Low Time Before VDD Becomes Invalid
tRRST
0
—
—
µs
Notes:
1. RSTB must be held low for at least 100 µs after the voltage supply has been ramped up.
2. RSTB needs to be asserted (pulled low) prior to the supply voltage being ramped down.
tSRST
tPRST
tRRST
VDD
RSTB
Figure 1. Reset Timing
Rev. 1.0
5
Si4836-A10
Table 4. FM Receiver Characteristics1,2
(VDD = 2.7 to 3.6 V, TA = –15 to 85 °C)
Parameter
Min
Typ
Max
Unit
64
—
109
MHz
—
2.2
—
µV EMF
LNA Input Resistance4,5
—
4
—
k
LNA Input Capacitance4,5
—
5
—
pF
—
50
—
dB
—
105
—
dBµV EMF
Input Frequency
Symbol
fRF
Sensitivity with Headphone
Network
Test Condition
(S+N)/N = 26 dB
3
m = 0.3
AM Suppression4,5,6,7
Input IP34,8
Adjacent Channel Selectivity4
±200 kHz
—
50
—
dB
Alternate Channel Selectivity4
±400 kHz
—
65
—
dB
Audio Output Voltage5,6,7,12
—
80
—
mVRMS
Audio Mono S/N5,6,7,9,10
—
55
—
dB
Audio Stereo S/N 3,4,5,7,9,10
—
55
dB
Audio Frequency Response Low4
–3 dB
—
—
30
Hz
Audio Frequency Response High4
–3 dB
15
—
—
kHz
—
0.1
0.5
%
Audio THD6,5,11
Audio Output Load Resistance4,10
RL
Single-ended
10
—
—
k
Audio Output Load Capacitance4,10
CL
Single-ended
—
—
50
pF
Notes:
1. Additional testing information is available in “AN569: Si4831/35/36/20/24/25-DEMO Board Test Procedure.”
Volume = maximum for all tests. Tested at RF = 98.1 MHz.
2. To ensure proper operation and receiver performance, follow the guidelines in “AN738: Si4825/36-A Antenna,
Schematic, Layout, and Design Guidelines.” Silicon Laboratories will evaluate schematics and layouts for qualified
customers.
3. Frequency is 64~109 MHz.
4. Guaranteed by characterization.
5. VEMF = 1 mV.
6. FMOD = 1 kHz, MONO, and L = R unless noted otherwise.
7. f = 22.5 kHz.
8. |f2 – f1| > 2 MHz, f0 = 2 x f1 – f2.
9. BAF = 300 Hz to 15 kHz, A-weighted.
10. At AOUT pin.
11. f = 75 kHz.
12. The test is done with Bass/Treble feature not enabled.
6
Rev. 1.0
Si4836-A10
Table 5. AM/SW Receiver Characteristics1, 2
(VDD = 2.7 to 3.6 V, TA = –15 to 85 °C)
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
fRF
Medium Wave (AM)
504
—
1750
kHz
Short Wave (SW)
2.3
—
28.5
MHz
(S+N)/N = 26 dB
—
30
—
µV EMF
Large Signal Voltage Handling5
THD < 8%
—
300
—
mVRMS
Power Supply Rejection Ratio5
∆VDD = 100 mVRMS, 100 Hz
—
40
—
dB
Audio Output Voltage3,6,8
—
60
—
mVRMS
Audio S/N3,4,6
—
55
—
dB
Audio THD3,6
—
0.1
0.5
%
180
—
450
µH
Input Frequency
Sensitivity3,4,5
Antenna Inductance5,7
Notes:
1. Additional testing information is available in “AN569: Si4831/35/36/20/24/25-DEMO Board Test Procedure.”
Volume = maximum for all tests. Tested at RF = 520 kHz and RF = 6 MHz.
2. To ensure proper operation and receiver performance, follow the guidelines in “AN738: Si4825/36-A Antenna,
Schematic, Layout, and Design Guidelines.” Silicon Laboratories will evaluate schematics and layouts for qualified
customers.
3. FMOD = 1 kHz, 30% modulation, 2 kHz channel filter.
4. BAF = 300 Hz to 15 kHz, A-weighted.
5. Guaranteed by characterization.
6. VIN = 5 mVrms.
7. Stray capacitance on antenna and board must be < 10 pF to achieve full tuning range at higher inductance levels.
8. The test is done with Bass/Treble feature not enabled.
Table 6. Reference Clock and Crystal Characteristics
(VDD = 2.7 to 3.6 V, TA = –15 to 85 °C)
Parameter
Symbol
Test Condition
Min
Typ
Max
Unit
—
32.768
—
kHz
–100
—
100
ppm
Crystal Oscillator Frequency
—
32.768
—
kHz
Crystal Frequency Tolerance
–100
—
100
ppm
—
—
3.5
pF
Reference Clock
XTALI Supported Reference Clock
Frequencies
Reference Clock Frequency
Tolerance for XTALI
Crystal Oscillator
Board Capacitance
Rev. 1.0
7
Si4836-A10
Table 7. Thermal Conditions
Parameter
Symbol
Min
Typ
Max
Unit
Thermal Resistance*
JA
—
80
—
°C/W
Ambient Temperature
TA
–15
25
85
°C
Junction Temperature
TJ
—
—
92
°C
*Note: Thermal resistance assumes a multi-layer PCB with the exposed pad soldered to a topside PCB pad.
Table 8. Absolute Maximum Ratings1,2
Parameter
Symbol
Value
Unit
Supply Voltage
VDD
–0.5 to 5.8
V
Input Current3
IIN
10
mA
Operating Temperature
TOP
–40 to 95
C
Storage Temperature
TSTG
–55 to 150
C
0.4
VPK
RF Input Level
4
Notes:
1. Permanent device damage may occur if the above Absolute Maximum Ratings are exceeded. Functional operation
should be restricted to the conditions as specified in the operational sections of this data sheet. Exposure beyond
recommended operating conditions for extended periods may affect device reliability.
2. The Si4836 devices are high-performance RF integrated circuits with certain pins having an ESD rating of < 2 kV HBM.
Handling and assembly of these devices should only be done at ESD-protected workstations.
3. For input pins RST, STATION, STEREO/LNA_EN, XTALO, XTALI, BAND, TUNE2, TUNE1.
4. At RF input pins, FMI and AMI.
8
Rev. 1.0
Si4836-A10
2. Typical Application Schematic
781(
5
N
6:
)0,
%$1'
6:RQO\
5287
*1'
9''
;7$/,
8
/287
781(
%$1'
781(
1&
;7$/2
)0,
67$7,21
567
5)*1'
5)*1'
$0,
$0,
X
7
5
N
/287
67(5(2/1$B(1
$17
$0DQWHQQD
N
&
$17
5
N
)0
$0,
X
$0
95
&
5
N
781(
%
N0
6
9''
5
N
567
5287
2SWLRQDO$0DLUORRSDQWHQQD
&
&
X
X
9''
729
67(5(2B/('
67$7,21B/('
<
&
.+]
S
&
S
2SWLRQDO
Notes:
1. Place C4 close to VDD and GND pins.
2. Pin 15 GND connects directly to GND plane on PCB.
3. Pin 5 leave floating.
4. To ensure proper operation and receiver performance, follow the guidelines in "AN738: Si4825/36-A Antenna,
Schematic, Layout, and Design Guidelines." Silicon Labs will evaluate the schematics and layouts for qualified
customers.
5. Pin 6 connects to the FM antenna interface and pin 8 connects to the AM antenna interface.
6. Place Si4836 as close as possible to antenna jack and keep the FMI and AMI traces as short as possible.
7. Recommend keeping the AM ferrite loop antenna at least 5 cm away from the tuner chip.
8. Keep the AM ferrite loop antenna at least 5 cm away from MCU, audio AMP, and other circuits which have AM
interference.
9. Place the transformer T1 away from any sources of interference and even away from the I/O signals of the Si4836.
Rev. 1.0
9
Si4836-A10
3. Bill of Materials
Table 9. Si4836-A Bill of Materials
Component(s)
Value/Description
Supplier
C1
Reset capacitor 0.1 μF, ±20%, Z5U/X7R
C4
Supply bypass capacitor, 0.1 μF, ±20%, Z5U/X7R
C5
Coupling capacitor, 0.47 μF, ±20%, Z5U/X7R
Venkel
B1
Ferrite bead 2.5 k/100 MHz
Murata
Variable resistor (POT), 100 k, ±10%
Kennon
R1
Reset timing resistor, 100 k, ±5%
Venkel
R3
Resistor, 133 k, ±1%
Venkel
R4
Resistor, 160 k, ±1%
Venkel
R5
Resistor, 67 k, ±1%
Venkel
R6
Resistor, 140 k, ±1
Venkel
U1
Si4836-A AM/FM/SW Analog Tune Analog Display Radio Tuner
S1
Band switch
VR1
ANT1
Murata
Murata
Silicon Laboratories
Any, depends on
customer
Ferrite stick,180–450 μH
Jiaxin
Optional Components
C2, C3
Y1
ANT2
10
Crystal load capacitors, 22 pF, ±5%, COG
(Optional: for crystal oscillator option)
32.768 kHz crystal (Optional: for crystal oscillator option)
Air loop antenna, 10–20 μH
Venkel
Epson or equivalent
Various
Rev. 1.0
Si4836-A10
4. Functional Description
Si4836
ADC
AMI
AM
ANT
RFGND
LNA
FMI
LOUT
DAC
ROUT
DSP
ADC
FM
ANT
DAC
AGC
0/90
TUNE1/2
ADC
CONTROL INTERFACE
BAND
XTAL
OSC
Stereo
REG
RST
VDD
Tone
2.0~3.6V
AFC
Station
XTALI
Figure 2. Si4836 Functional Block Diagram
4.1. Overview
4.2. FM Receiver
The Si4836 is the high performance mechanical-tuned
digital CMOS AM/FM/SW radio receiver IC that
integrates the complete receiver function from antenna
input to audio output. The Si4836 extends Silicon
Laboratories multi-band tuner family, and further
increases the ease and attractiveness of design radio
reception to audio devices through small size and board
area, minimum component count, and superior, proven
performance. The Si4836 enhances the FM and SW
band coverage and further supports China TV channels
audio reception in FM band. The Si4836 removes any
requirements for manually tuning components during
the manufacturing process.
The Si4836 integrates a low noise amplifier (LNA)
supporting the worldwide FM broadcast band (64 to
109 MHz) and the TV audio stations within the
frequency range in China area are also supported.
Leveraging Silicon Laboratories' proven and patented
digital low intermediate frequency (low-IF) receiver
architecture, the Si4836 delivers desired RF
performance and interference rejection in AM, FM, and
SW bands. The high integration and complete system
production test simplifies design-in, increases system
quality, and improves manufacturability.
Pre-emphasis and de-emphasis is a technique used by
FM broadcasters to improve the signal-to-noise ratio of
FM receivers by reducing the effects of high frequency
interference and noise. When the FM signal is
transmitted, a pre-emphasis filter is applied to
accentuate the high audio frequencies. All FM receivers
incorporate a de-emphasis filter which attenuates high
frequencies to restore a flat frequency response. Two
time constants are used in various regions. The deemphasis time constant can be chosen to be 50 or
75 µs. Refer to "AN738: Si4825/36-A Antenna,
Schematic, Layout, and Design Guidelines.”
The Si4836 also has advanced stereo blending that
employs adaptive noise suppression. As a signal quality
degrades, the Si4836 gradually combines the stereo left
and right audio channels to a mono audio signal to
maintain optimum sound fidelity under varying reception
conditions. The Si4836 can drive a stereo light with the
stereo/mono information so that the user can easily
Rev. 1.0
11
Si4836-A10
discern the signal quality.
4.5. Frequency Tuning
The stereo light up criteria are defined using both RSSI
and the Left and Right separation levels as these two
specifications are the primary factors for stereo
listening. The criteria can be set between two
conditions: the Left and Right channels are separated
by more than 6 dB with RSSI at >20 dB or they are
separated by more than 12 dB with RSSI at >28 dB.
The selection can be set up using different values of the
external resister. Refer to "AN738: Si4825/36-A
Antenna, Schematic, Layout, and Design Guidelines.”
A valid channel can be found by tuning the
potentiometer that is connected to the TUNE1 and
TUNE2 pin of the Si4836 chip.
4.3. AM Receiver
The highly integrated Si4836-A10 supports worldwide
AM band reception from 504 to 1750 kHz with five subbands using a digital low-IF architecture with a minimum
number of external components and no manual
alignment required. This patented architecture allows
for high-precision filtering, offering excellent selectivity
and SNR with minimum variation across the AM band.
The Si4836 supports the worldwide AM band with five
sub-bands. One of the bands is a universal AM band
(AM4, 520–1730 kHz) supporting both 9 kHz and
10 kHz channel spaces for all regional AM standards of
the world. Similar to the FM receiver, the Si4836
optimizes sensitivity and rejection of strong interferers,
allowing better reception of weak stations.
To offer maximum flexibility, the receiver supports a
wide range of ferrite loop sticks from 180–450 µH. An
air loop antenna is supported by using a transformer to
increase the effective inductance from the air loop.
Using a 1:5 turn ratio inductor, the inductance is
increased by 25 times and easily supports all typical AM
air loop antennas, which generally vary between 10 and
20 µH.
4.4. SW Receiver
The Si4836 supports 36 short wave (SW) band
receptions from 2.3 to 28.5 MHz, 18 of which are meter
wave band (Narrow), and the rest of the SW bands are
with wider frequency range that can be used in SW
radio with 1 or 2 SW bands. Si4836 supports extensive
short wave features such as minimal discrete
components and no factory adjustments. The Si4836
supports using the FM antenna to capture short wave
signals.
12
To offer easy tuning, the Si4836 also supports a station
LED light. It will light up the LED if the RF signal quality
passes the LED sensitivity threshold when tuned to a
valid station.
4.6. Band Select
The Si4836 supports worldwide AM band with five subbands, US/Europe/Japan/China FM band with five subbands, and SW band with 36 sub-bands. For details on
band selection, refer to “AN738: Si4825/36-A Antenna,
Schematic, Layout, and Design Guidelines."
4.7. Bass and Treble
The Si4836 further supports bass and treble tone
control for superior sound quality. Pins 12 can be
configured for tone control with single push button if the
system can provide 32.768 kHz external clock to Pin13,
allowing customers to adjust the bass and treble in a
cyclic way. For further configuration details, refer to
"AN738: Si4825/36-A Antenna, Schematic, Layout, and
Design Guidelines."
4.8. Reset, Powerup, and Powerdown
Setting the RSTB pin low will disable analog and digital
circuitry, reset the registers to their default settings, and
disable the bus. Setting the RSTB pin high will bring the
device out of reset.
Figure 1 shows typical reset, startup, and shutdown
timings for the Si4836. RSTB must be held low
(asserted) during any power supply transitions and kept
asserted as specified in Figure 1 after the power
supplies are ramped up and stable. Failure to assert
RSTB as indicated here may cause the device to
malfunction and may result in permanent device
damage.
A powerdown mode is available to reduce power
consumption when the part is idle. Putting the device in
powerdown mode will disable analog and digital circuitry
while keeping the bus active.
Rev. 1.0
Si4836-A10
5. Pin Descriptions: Si4836-A10
LOUT
1
16
ROUT
TUNE1
2
15
GND
TUNE2
3
14
VDD
BAND
4
13
XTALI
NC
5
12
XTALO
FMI
6
11
STATION
RFGND
7
10
STEREO/LNA_EN
AMI
8
9
RST
Pin Number(s)
Name
1
LOUT
Left audio output
2
TUNE1
Frequency tuning
3
TUNE2
Frequency tuning
4
BAND
Band selection and de-emphasis selection
5
NC
No connect. Leave floating.
6
FMI
FM RF inputs. FMI should be connected to the antenna trace.
7
RFGND
8
AMI
AM RF input. AMI should be connected to the AM antenna.
9
RST
Device reset (active low) input
10
Description
RF ground. Connect to ground plane on PCB.
STEREO/LNA_EN Stereo indicator, enable the SW external LNA in SW mode.
11
STATION
Station indicator
12
XTALO
Crystal oscillator output
13
XTALI
Crystal oscillator input/external reference clock input
14
VDD
Supply voltage. May be connected directly to battery.
15
GND
Ground. Connect to ground plane on PCB.
16
ROUT
Right audio output
Rev. 1.0
13
Si4836-A10
6. Ordering Guide
Part Number*
Si4836-A10-GS
Description
AM/FM/SW Broadcast Radio Receiver
Package
Type
Operating
Temperature/Voltage
16L SOIC
Pb-free
–15 to 85 °C
2.0 to 3.6 V
*Note: Add an “(R)” at the end of the device part number to denote tape and reel option. The devices will typically operate at
25 °C with degraded specifications for VDD voltage ramped down to 2.0 V.
14
Rev. 1.0
Si4836-A10
7. Package Outline: Si4836-A10
The 16-pin SOIC illustrates the package details for the Si4836-A10. Table 10 lists the values for the dimensions
shown in the illustration.
Figure 3. 16-Pin SOIC
Rev. 1.0
15
Si4836-A10
Table 10. Package Dimensions
Dimension
A
A1
A2
b
c
D
E
E1
e
L
L2
h
θ
aaa
bbb
ccc
ddd
Min
—
0.10
1.25
0.31
0.17
Max
1.75
0.25
—
0.51
0.25
9.90 BSC
6.00 BSC
3.90 BSC
1.27 BSC
0.40
1.27
0.25 BSC
0.25
0°
0.50
8°
0.10
0.20
0.10
0.25
Notes:
1. All dimensions shown are in millimeters (mm) unless otherwise noted.
2. Dimensioning and Tolerancing per ANSI Y14.5M-1994.
3. This drawing conforms to the JEDEC Solid State Outline MS-012, Variation AC.
4. Recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for
Small Body Components.
16
Rev. 1.0
Si4836-A10
8. PCB Land Pattern: Si4836-A10
Figure 4, “PCB Land Pattern,” illustrates the PCB land pattern details for the Si4836-A10-GS SOIC. Table 11 lists
the values for the dimensions shown in the illustration.
Figure 4. PCB Land Pattern
Table 11. PCB Land Pattern Dimensions
Dimension
Feature
(mm)
C1
Pad Column Spacing
5.40
E
Pad Row Pitch
1.27
X1
Pad Width
0.60
Y1
Pad Length
1.55
Notes:
1. This Land Pattern Design is based on IPC-7351 pattern SOIC127P600X165-16N
for Density Level B (Median Land Protrusion).
2. All feature sizes shown are at Maximum Material Condition (MMC) and a card
fabrication tolerance of 0.05 mm is assumed.
Rev. 1.0
17
Si4836-A10
9. Top Marking
9.1. Si4836-A10 Top Marking
9.2. Top Marking Explanation
Mark Method:
Laser
Pin 1 Mark:
Mold Dimple (Bottom-Left Corner)
Font Size:
0.71 mm (2.0 Point) Right-Justified
Line 1 Mark Format: Custom Part Number
Si4836A10
Circle = 1.3 mm Diameter
“e3” Pb-Free Symbol
YY = Year
Line 2 Mark Format: WW = Work week
Assigned by the Assembly House. Corresponds to the
year and work week of the mold date.
TTTTTT = Manufacturing code
18
Manufacturing Code from the Assembly Purchase
Order form.
Rev. 1.0
Si4836-A10
10. Additional Reference Resources
Contact your local sales representatives for more information or to obtain copies of the following references:
AN738: Si4825/36-A Antenna, Schematic, Layout, and Design Guidelines
AN569: Si4831/35/36/20/24/25-DEMO Board Test Procedure
 Si4836-DEMO Board User’s Guide


Rev. 1.0
19
Si4836-A10
DOCUMENT CHANGE LIST
Revision 0.1 to Revision 0.8











Added ambient temperature range to "Table 1.
Recommended Operating Conditions"
Updated "Functional Block Diagram"
Updated Table 2, "DC Characteristics"
Updated Table 4, "FM Receiver Characteristics"
Updated Table 5, "AM/SW Receiver Characteristics"
Updated Section "2.Typical Application Schematic"
Updated Section “4.3. AM Receiver"
Updated Section “4.7. Bass and Treble"
Updated Section “5. Pin Descriptions: Si4836-A10"
Updated Section "6. Ordering Guide"
Updated Section "10. Additional Reference
Resources"
Revision 0.8 to Revision 1.0


20
Updated Table 3. "Reset Timing Characteristics"
Inserted Section 4.8. "Reset, Powerup, and
Powerdown"
Rev. 1.0
Smart.
Connected.
Energy-Friendly
Products
Quality
Support and Community
www.silabs.com/products
www.silabs.com/quality
community.silabs.com
Disclaimer
Silicon Laboratories intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers
using or intending to use the Silicon Laboratories products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific
device, and "Typical" parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Laboratories
reserves the right to make changes without further notice and limitation to product information, specifications, and descriptions herein, and does not give warranties as to the accuracy
or completeness of the included information. Silicon Laboratories shall have no liability for the consequences of use of the information supplied herein. This document does not imply
or express copyright licenses granted hereunder to design or fabricate any integrated circuits. The products must not be used within any Life Support System without the specific
written consent of Silicon Laboratories. A "Life Support System" is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected
to result in significant personal injury or death. Silicon Laboratories products are generally not intended for military applications. Silicon Laboratories products shall under no
circumstances be used in weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons.
Trademark Information
Silicon Laboratories Inc., Silicon Laboratories, Silicon Labs, SiLabs and the Silicon Labs logo, CMEMS®, EFM, EFM32, EFR, Energy Micro, Energy Micro logo and combinations
thereof, "the world’s most energy friendly microcontrollers", Ember®, EZLink®, EZMac®, EZRadio®, EZRadioPRO®, DSPLL®, ISOmodem ®, Precision32®, ProSLIC®, SiPHY®,
USBXpress® and others are trademarks or registered trademarks of Silicon Laboratories Inc. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of
ARM Holdings. Keil is a registered trademark of ARM Limited. All other products or brand names mentioned herein are trademarks of their respective holders.
Silicon Laboratories Inc.
400 West Cesar Chavez
Austin, TX 78701
USA
http://www.silabs.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement