PowerSeries – Assigning a Keypad to a Partition

PowerSeries – Assigning a Keypad to a Partition
PowerSeries – Assigning a Keypad to a Partition
Panels:
PC5010 (Power832)
Overview:
Keypads connected to the PC5010 panel can be assigned one of three ways: a keypad can be
assigned to operate partition 1, partition 2 or as a global keypad. Global keypads will not display
any information (except for a trouble condition, if present) until the keypad is temporarily assigned
to either partition 1 or partition 2. A global keypad allows the user to operate two partitions
through the use of one keypad.
Programming keypad partition assignment is a two-step process:
-
Enable Partition 2
Assign the Keypad to a Partition and Slot
Keypad Supervision
Program Sections:
Section [201]
Section [000], [0]
Section [902]
Partition 2 Enable
Keypad Assignment
Module Supervision Field
Step 1 – Enable Partition 2
Partition 2 must be enabled before keypads assigned to partition 2 will operate. To enable
partition 2, perform the following:
Enter [*][8][Installer’s Code]
Enter [201]
Press [1] to turn ON option [1]
Enter Installer’s Programming
Enter Partition 2 Enable
Enable Partition 2
Step 2 – Keypad Assignment
Program the Partition Assignment and Slot of each keypad. To assign the keypad, perform the
following:
Enter [*][8][Installer’s Code]
Enter [000]
Enter [0]
Enter Installer’s Programming
Enter Keypad Assignment Section
Enter Partition and Slot Section
Enter a two-digit number. The first number represents the partition assigned to the keypad:
Enter data [0]
Enter data [1]
Enter data [2]
for Global Mode
for Partition 1
for Partition 2
The second digit represents the supervisory slot:
Enter data [1] to [8]
for supervisory slot #1 to #8
The same procedure must be performed on each keypad.
Note:
Keypads must each be assigned to a specific slot for the keypads to be properly
supervised.
Note:
If an LCD5500Z keypad is connected to the panel, it must be assigned to slot #8 for
downloading purposes. In addition, only one LCD5500(Z) can be assigned to Slot
8. If LCD programming changes are made using the DLS software, the keypad
assigned to slot #8 will transmit the changes to all the other LCD5500Z keypads on
the system after the download is complete.
Step 3 – Module Supervisory Reset
Since all modules are automatically detected and supervised by the panel within the first minute
after being connected, a Module Supervisory trouble condition may occur after keypad slot
assignments are changed. After all keypads have been assigned to a Partition and Slot, perform
the following to perform a Module Supervisory Reset:
Enter [*][8][Installer’s Code]
Enter [902]
Press [#] [#]
Enter Installer’s Programming
Enter Module Supervision Reset
Exit Installer Programming
Wait 1 minute.
To verify what modules are present, perform the following:
Enter [*][8][Installer’s Code]
Enter [903]
Enter Installer’s Programming
Enter Module Supervision Display
The keypad will display the modules present.
Note:
LED keypads will be limited to the number of modules it can display. To determine
which LED represents which module, refer to the Installation Manual, Section 2.7.
Technical Tips:
1. If a keypad is assigned to partition 2 and partition 2 is not enabled, the keypad will not
function. To correct the issue, press and hold the [#] key for 3 seconds then press and
hold [1] to temporarily assign the keypad to partition 1. Enter Installer Programming and
enable partition 2 (Step 1 above).
2. To temporarily assign a global keypad to a partition, press and hold [1] for partition 1 or
[2] for partition 2. If no key is pressed for 20 seconds the keypad will return to the global
state.
3. A partition keypad can be temporarily assigned to another partition. To do this, press and
hold the [#] key for 3 seconds. The keypad will beep three times. Press and hold [1] for
partition 1 or [2] for partition 2. If no key is pressed for 20 seconds the keypad will return
to the partition it was originally assigned to.
Quick Test:
Violate a zone assigned to Partition 2 and ensure it is displayed on a partition 2 keypad.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising