ENH202_User Manual_20110704
LONG RANGE
WIRELESS ACCESS POINT / CLIENT BRIDGE
Model : ENH202
User Manual
Version : 1.0
Table of Contents
1 PRODUCT OVERVIEW ...................................................................................................................................................... 5
1.1 FEATURE ....................................................................................................................................................................... 5
1.2 BENEFITS....................................................................................................................................................................... 6
1.3 PACKAGE CONTENTS...................................................................................................................................................... 8
1.4 SYSTEM REQUIREMENT .................................................................................................................................................. 8
1.5 HARDWARE OVERVIEW .................................................................................................................................................. 8
2 ENH202 MULTI-FUNCTION INSTRUCTION GUIDE ................................................................................................... 9
2.1 ACCESS POINT .............................................................................................................................................................. 9
2.2 ACCESS POINT WITH WDS FUNCTION ............................................................................................................................ 9
2.3 CLIENT BRIDGE ............................................................................................................................................................ 10
2.4 WDS BRIDGE.............................................................................................................................................................. 10
2.5 CLIENT ROUTER ........................................................................................................................................................... 11
3 COMPUTER CONFIGURATION INSTRUCTION ......................................................................................................... 12
3.1 ASSIGN A STATIC IP ..................................................................................................................................................... 12
3.2 LOGGING METHOD...................................................................................................................................................... 13
4 STATUS .............................................................................................................................................................................. 14
4.1 SAVE/LOAD ................................................................................................................................................................. 14
4.2 MAIN ......................................................................................................................................................................... 15
4.3 WIRELESS CLIENT LIST ................................................................................................................................................. 16
4.4 SYSTEM LOG ............................................................................................................................................................... 17
4.5 CONNECTION STATUS .................................................................................................................................................. 18
4.6 DHCP CLIENT TABLE ................................................................................................................................................... 19
5 SYSTEM ............................................................................................................................................................................. 20
5.1 SWITCHING OPERATION MODE .................................................................................................................................... 20
6 WIRELESS CONFIGURATION ........................................................................................................................................ 22
6.1 WIRELESS SETTINGS..................................................................................................................................................... 22
6.1.1 Access Point Mode ........................................................................................................................................ 22
6.1.2 Client Bridge Mode ....................................................................................................................................... 25
6.1.3 WDS Bridge Mode ......................................................................................................................................... 27
6.1.4 Client Router Mode ....................................................................................................................................... 29
6.2 WIRELESS SECURITY SETTINGS...................................................................................................................................... 31
6.2.1 WEP ................................................................................................................................................................ 31
6.2.2 WPA-PSK ....................................................................................................................................................... 32
6.2.3 WPA2-PSK ..................................................................................................................................................... 33
6.2.4 WPA-PSK Mixed ............................................................................................................................................ 34
6.2.5 WPA................................................................................................................................................................ 35
6.2.6 WPA2 ............................................................................................................................................................. 36
6.2.7 WPA Mixed .................................................................................................................................................... 37
6.3 WIRELESS ADVANCED SETTINGS ................................................................................................................................... 38
6.4 WIRELESS MAC FILTER ................................................................................................................................................ 40
6.5 WDS LINK SETTINGS ................................................................................................................................................... 41
7 LAN SETUP ....................................................................................................................................................................... 42
7.1 IP SETTINGS ................................................................................................................................................................ 42
7.2 SPANNING TREE SETTINGS ........................................................................................................................................... 43
8 ROUTER SETTINGS ......................................................................................................................................................... 44
8.1 WAN SETTINGS .......................................................................................................................................................... 44
8.1.1 Static IP .......................................................................................................................................................... 44
8.1.2 DHCP (Dynamic IP) ...................................................................................................................................... 46
8.1.3 PPPoE (Point-to-Point Protocol over Ethernet) .......................................................................................... 48
8.1.4 PPTP (Point-to-Point Tunneling Protocol) .................................................................................................. 50
8.2 LAN SETTINGS (ROUTER MODE).................................................................................................................................. 52
8.3 VPN PASS THROUGH .................................................................................................................................................. 53
8.4 PORT FORWARDING..................................................................................................................................................... 54
8.5 DMZ.......................................................................................................................................................................... 55
9 MANAGEMENT SETTINGS ........................................................................................................................................... 56
9.1 ADMINISTRATION ........................................................................................................................................................ 56
9.2 MANAGEMENT VLAN ................................................................................................................................................. 58
9.3 SNMP SETTINGS ........................................................................................................................................................ 59
9.4 BACKUP/RESTORE SETTINGS ........................................................................................................................................ 60
9.5 FIRMWARE UPGRADE ................................................................................................................................................... 61
9.6 TIME SETTINGS ............................................................................................................................................................ 62
9.7 LOG ............................................................................................................................................................................ 63
9.8 DIAGNOSTICS .............................................................................................................................................................. 64
10 NETWORK CONFIGURATION EXAMPLE ................................................................................................................. 65
10.1 ACCESS POINT .......................................................................................................................................................... 65
10.2 CLIENT BRIDGE MODE ............................................................................................................................................... 66
10.3 WDS BRIDGE MODE ................................................................................................................................................. 67
10.4 CLIENT ROUTER......................................................................................................................................................... 68
EUROPE – EU DECLARATION OF CONFORMITY ........................................................................................................................... 71
About This Document
This document is written by EnGenius Inc. EnGenius Inc. has rights to change any of this
document without notice and all rights reserved. This document can only be used for guiding
the configuration setup of EnGenius products.
This document is to demonstrate the EnGenius ENH202 Wireless Access Point & Client
Bridge. Please read the document carefully before setup the ENH202. If the damage is caused
by the inappropriate behaviors, the repair will not be included in the warranty.
Formats
This document uses following symbols to indicate and highlight special message.
Caution: This symbol represents the Vital message and it could be harmful for
the device or settings.
Note: This symbol represents the important message for the settings.
Tip: This symbol represents the alternative choice that can save time or
resources.
Before you start__________________________________________________
The following equipments are essential to setup the ENH202:
1. One Computer/Notebook and internet accessible.
2. Two Ethernet Cables.
3. One EnGenius device – ENH202.
The equipments listed above are only for setup the ENH202, you will need more
equipment to connect the internet and it is depend on your internet network structure. You
may refer to the chapter 2 for more information.
1 Product Overview
Thank you for using ENH202. It is a powerful, enhanced, enterprise scale product with 4
multi-functions Access Point, Client Bridge, WDS and Client Router.
ENH202 uses the latest wireless technology 802.11n standard. It has faster transmit/receive
wireless speed. ENH202 gives you a great advantage to save your time and cost to expend
your network. It is also compatible with 802.11b and 802.11g.
ENH202 is easily to install almost anywhere with Power over Ethernet for quick indoor
installation and regular Power by Adapter. ENH202 can manage power level control, Narrow
bandwidth selection, Traffic shaping and Real-time RSSI indicator. ENH202 is fully support of
security encryption including Wi-Fi Protected Access (WPA-PSK/WPA2-PSK), 64/128/152-bit
WEP Encryption and IEEE 802.1x with RADIUS.
1.1 Feature
The following list describes the design of the ENH202 made possible through the power and
flexibility of wireless LANs:
a) Difficult-to-wire environments
There are many situations where wires cannot be laid easily. Historic buildings,
older buildings, open areas and across busy streets make the installation of LANs
either impossible or very expensive.
b) Temporary workgroups
Consider situations in parks, athletic arenas, exhibition centers, disaster-recovery,
temporary offices and construction sites where one wants a temporary WLAN
established and removed.
c) The ability to access real-time information
Doctors/nurses, point-of-sale employees, and warehouse workers can access
real-time information while dealing with patients, serving customers and
processing information.
d) Frequently changed environments
Show rooms, meeting rooms, retail stores, and manufacturing sites where
frequently rearrange the workplace.
e) Wireless extensions to Ethernet networks
Network managers in dynamic environments can minimize the overhead caused by
moves, extensions to networks, and other changes with wireless LANs.
f) Wired LAN backup
Network managers implement wireless LANs to provide backup for mission-critical
applications running on wired networks.
g) Training/Educational facilities
Training sites at corporations and students at universities use wireless connectivity
to ease access to information, information exchanges, and learning.
Benefits
High Speed Data Rate
Up to 300Mbps
High Output Power up
to 29 dBm
IEEE 802.11b/g/n
Compliant
Multi-Function
Point-to-point,
Point-to-multipoint
Wireless Connectivity
Support RSSI Indicator
(CB mode)
Power-over-Ethernet
Support Multi-SSID
function (4 SSID) in AP
mode
WPA2/WPA/ WEP/ IEEE
802.1x support
MAC address filtering in
AP mode
PPPoE/PPTP function
support (AP Router/CR
mode)
SNMP Remote
Configuration
Management
QoS (WMM) support
Capable of handling heavy data payloads such as MPEG video
streaming
Extended excellent Range and Coverage
Fully Interoperable with IEEE 802.11b/IEEE 802.11g/IEEE 802.11n
compliant devices
Users can use different mode in various environment
Let users transfer data between two buildings or multiple buildings
Users can select the best signal to connect with AP easily
Flexible Access Point locations and cost savings. ENH202 must uses
the adapter provided in the package.
Allow clients to access different networks through a single access
point and assign different policies and functions for each SSID by
manager
Fully support all types of security types.
Ensures secure network connection
Easy to access internet via ISP service authentication
Help administrators to remotely configure or manage the Access
Point easily.
Enhance user performance and density
1.2 Benefits
Access Point Mode
Use this feature to setup the access point’s configuration
information. It has support adjusting transmit power and channel.
Client can access the network with different regulatory settings
and automatically change to the local regulations.
Client Bridge Mode
Use this feature to connect to an Access Point and enjoy the great
speed of surfing internet.
WDS Mode
Use this feature to link multiple APs in a network, All clients
associated with any APs can communicate each other like an
ad-hoc mode.
Client Router Mode
This feature functions completely opposite but similarly with AP
Router Mode. Client Router connected to an AP wirelessly and
transmit internet connection protocol through AP to access the
internet.
Multiple SSIDs
ENH202 supports up to 4 SSIDs on your access point. The
following options can be set to each SS to each SSID:
- SSID for public or private network
- Authentication is fully supported
- VLAN identifier
- Radius accounting identifier
- Profile isolation for infrastructure network
VLAN
Specify a VLAN number for each SSID to separate the services
among clients.
QoS
Use this feature to limit the incoming or outgoing throughput.
Wi-Fi Protect Access
Wi-Fi Protect Access is a standard-based interoperable security
enhancement that increases the level of data protection and
access control for existing and future wireless LAN system. It is
compatible with IEEE 802.11i standard WPA leverages TKIP and
802.1X for authenticated key management.
1.3 Package Contents
Open the package carefully, and make sure that none of the items listed below are missing.
Do not discard the packing materials, in case of return; the unit must be shipped in its original
package.






1* Wireless Access Point / Client Bridge (ENH202)
1* 24V/1A Power Adapter
1* PoE Injector(EPE-24R)
1* Pole Mount
1* QIG
1* CD (User Manual)
Using other Power Adapter than the one included with ENH202 may cause damage of the
device.
1.4 System Requirement
The following conditions are the minimum system requirement.
 A computer with an Ethernet interface and operating under Windows XP, Vista, 7 or
Linux.
 Internet Browser that supports HTTP and JavaScript.
1.5 Hardware Overview
Physical Interface
- 1 x LAN Port with PoE support
- 1 x LAN Port
- 1 x Reset
Data rate
300 Mbps
LEDs status
- Power Status
- LAN (10/100Mbps)
- WLAN (Wireless is up)
- 3 x Link Quality (Client Bridge mode)
2 ENH202 Multi-Function Instruction Guide
2.1 Access Point
In the Access Point Mode, ENH202 function likes a central connection for any stations or
clients that support IEEE 802.11b/g/n network. Stations and Client must configure the same
SSID and Security Password to associate within the range. ENH202 supports 4 different SSIDs
to separate different clients at the same time.
2.2 Access Point with WDS Function
ENH202 also supports WDS function in Access Point Mode without losing AP’s capabilities.
Configure others Access Point’s Wireless MAC Address in both Access Point devices to
enlarge the wireless area by enabling WDS Link Settings. WDS function can support up to 8
different AP’s MAC addresses.
Not every Access Point device has support WDS in Access Point Mode. It is
recommended using ENH202 if you would like to use this service.
2.3 Client Bridge
In the Client Bridge Mode, the ENH202 function likes a wireless client connecting to an Access
Point wirelessly and surf internet whenever you want. Using Site Survey to scan all the Access
Point within the range and configure its SSID and Security Password to associate with it.
Connect you station to the LAN port of the ENH202 via Ethernet.
2.4 WDS Bridge
In the WDS Bridge Mode, the ENH202 can wirelessly connect different LANs by just simply
configure each other’s MAC Address and Security Settings. This mode is used when two wired
LANs locate in small distance and want to communicate each other. The best solution is using
ENH202 wirelessly connect two wired LANs. WDS Bridge Mode can establish 16 WDS links,
the network diagram is like a Star.
WDS Bridge Mode is unlike Access Point. APs linked by WDS are using the same
frequency channel, more APs connected together may lower throughput. Please be aware to
avoid loop connection diagram, otherwise enable Spanning Tree Function.
2.5 Client Router
In the Client Router Mode, the ENH202 has DHCP Server build inside that allows many LANs
automatically generate an IP address to share the same Internet. Connect an AP/WISP
Wirelessly and connect to LANs via wired. Client Router Mode is act completely opposite to
the AP Router Mode.
3 Computer Configuration Instruction
The default operating mode is Client Bridge. Client Bridge will not assign an IP address to the
computer/notebook. Therefore, follow the steps to assign an IP address to your Ethernet card.
3.1 Assign a Static IP
In order to configure ENH202, please follow the instruction below:
1. In the Control Panel, double click Network
Connections and then double click on the
connection of your Network Interface Card (NIC).
You will then see the following screen.
2. Select Internet Protocol (TCP/IP) and then click
on the Properties button. This will allow you to
configure the TCP/IP settings of your PC/Notebook
3. Select Use the following IP address radio button
and then enter the IP address and subnet mask.
Ensure that the IP address and subnet mask are on
the same subnet as the device.
4. Click on the OK button to close this window, and
then close LAN properties window.
IP Address entered in the TCP/IP Properties needs to be at the same subnet of the ENH202 IP
Address. For example: ENH202’s default IP Address is 192.168.1.1 so the IP Address in the
TCP/IP settings could be 192.168.1.10.
3.2 Logging Method
After complete the IP settings from last section, you can now access the web-based
configuration menu.
1. Open web browser
2. Enter IP 192.168.1.1 into you address filter.
Caution: If you have changed the ENH202 LAN IP address, make sure you enter the correct IP
Address.
3. After connected to the ENH202 successfully, browser will pop out a Windows Security
window. Please enter the correct Username and Password.
4. The default Username and Password are both admin.
If you have changed the Username and Password, please enter your own
Username and Password.
4 Status
Status section is on the navigation drop-down menu. You will then see three options: Main,
Wireless Client List, System Log, WDS Link Status, Connection Status, and DHCP Client Table.
Each option is described in detail below.
4.1 Save/Load
This page allows viewing the modified changes. The changes show in the Unsaved changes
list table. You can decide to cancel all the changes or to compile to the new setting.
You cannot cancel the specific settings. You can only compile all the settings or revert to the
previous settings.
4.2 Main
Click on the Main link under the Status drop-down menu or click Home from the top-right
of the webpage. The status that is displayed corresponds with the operating mode that is
selected. Information such as operating mode, system up time, firmware version, serial
number, kernel version and application version are displayed in the ‘System’ section. LAN IP
address, subnet mask, and MAC address are displayed in the ‘LAN’ section. In the ‘Wireless
section, the frequency, channel is displayed. Since this device supports multiple-SSIDs, the
details of each SSID, such as ESSID and its security settings are displayed.
4.3 Wireless Client List
Click on the Wireless Client List link under the Status drop-down menu. This page displays
the list of Clients that are associated to the ENH202.
The MAC addresses and signal strength for each client is displayed. Click on the Refresh
button to refresh the client list
4.4 System Log
Click on the System Log link under the Status drop-down menu. The device automatically
logs (records) events of possible interest in its internal memory. If there is not enough internal
memory for all events, logs of older events are deleted, but logs of the latest events are
retained.
4.5 Connection Status
Click on the Connection Status link under the Status drop-down menu. This page displays
the current status of the network, including network type, SSID, BSSID, connection status,
wireless mode, current channel, security, data rate, noise level and signal strength.
4.6 DHCP Client Table
Click on the DHCP Client List link under the Status drop-down menu. This page displays the
list of Clients that are associated to the ENH202 through DHCP.
The MAC addresses and signal strength for each client is displayed. Click on the Refresh
button to refresh the client list.
5 System
5.1 Switching Operation Mode
The ENH202 supports 4+1 operation modes: Access Point, Client Bridge, WDS Bridge, and
Client Router. In order to switching between the operating modes, please go to System ->
Operation mode.
Click System Properties under System Section to begin.
.
Device Name: Specify a name for the device. It is not the broadcast SSID. It will be shown in
SNMP management.
Country/Region: Select a Country/Region to conform local regulation.
Operation Mode: Select an operation mode via Radio Button.
Click Accept to confirm the changes.
Accept does not compile the changes, you must go to Status -> Save/Load to apply the new
settings. Please refer to the chapter 4.1 for more detail.
If you would like to use Access Point with WDS Function mode, please select Access Point
Mode and then enable WDS function in the Wireless Network section.
6 Wireless Configuration
This section will guide you through all the wireless settings. Please read the instruction
carefully. Inappropriate setting could lower the performance or affect the network structure.
Before you continue, please make sure you have chosen the correct operating mode.
6.1 Wireless Settings
This section is the basic wireless settings. Please read the description carefully and check the
steps on chapter 10 in case you need more detail information.
6.1.1 Access Point Mode
Wireless Mode
The wireless mode supports 802.11b/g/n mixed modes. It is
compatible with the most common known wireless band.
Channel HT Mode
The default channel bandwidth is 40 MHz. The larger channel can
provide better transmit quality and speed.
Extension Channel
Specify the upper channel or lower channel selection. It may
influence the Auto channel function
Channel / Frequency
The channel availability is based on the country’s regulation.
Auto
Place a Check mark to enable Auto channel selection.
AP Detection
AP Detection can help to select a best channel by scan nearby
area.
Current Profile
Configure up to four different SSIDs, it can help to divide group
of clients to access the network. Press Edit to configure the
profile and place a Check to enable extra SSID.
Profile Isolation
Restricted Client to communicate with different VID by Selecting
the Radio button.
Accept / Cancel
Press Accept to confirm the changes or Cancel to return previous
settings.
Accept does not compile the changes, you must go to Status -> Save/Load to apply the new
settings. Please refer to the chapter 4.1 for more detail.
SSID
Specify the SSID for current profile.
VLAN ID
Specify the VLAN tag for current profile.
Suppressed SSID
Place a Check to hide the SSID. Client will not be able to see the
broadcast SSID in Site Survey.
Station Separation
Select the Radio Button to allow / deny client to communicate
each other.
Wireless Security
Please refer to the Wireless Security section.
Save / Cancel
Press Save to save the changes or Cancel to return previous
settings.
6.1.2 Client Bridge Mode
Wireless Mode
The wireless mode supports 802.11b/g/n mixed modes. It is
compatible with the most common known wireless band.
SSID
Specify the SSID if known. SSID text box will be automatically fill
in when select an AP in the Site Survey.
Site Survey
Using Site Survey to scan nearby APs and then select the AP to
establish the connection.
Prefer BSSID
Specify the MAC address if known. Prefer BSSID text box will be
automatically fill in when select an AP in the Site Survey.
WDS Client
Place a Radio button to Enable / Disable WDS Client.
Wireless Security
Please refer to the chapter 6.2 for details.
Accept / Cancel
Press Accept to confirm the changes or Cancel to return previous
settings.
Accept does not compile the changes, you must go to Status -> Save/Load to apply the new
settings. Please refer to the chapter 4.1 for more detail.
Profile
After Site Survey, webpage will display all nearby area’s Access
Point. Click the BSSID if you would like to connect with it.
Wireless Security
Please refer to the Wireless Security section.
Refresh
Press Refresh to scan again.
If the Access Point is suppressed its own SSID, SSID section will be blank, the SSID must be
filled in manually.
6.1.3 WDS Bridge Mode
Wireless Mode
The wireless mode supports 802.11b/g/n mixed modes. It is
compatible with the most common known wireless band.
Channel HT Mode
The default channel bandwidth is 40 MHz. The larger channel can
provide better transmit quality and speed.
Extension Channel
Specify the upper channel or lower channel selection. It may
influence the Auto channel function
Channel / Frequency
The channel availability is based on the country’s regulation.
Accept / Cancel
Press Accept to confirm the changes or Cancel to return previous
settings.
Accept does not compile the changes, you must go to Status -> Save/Load to apply the new
settings. Please refer to the chapter 4.1 for more detail.
MAC Address
Enter the Access Point’s MAC address that you would like to
extend the wireless area into the MAC address filter.
Mode
Select Disable or Enable from the drop down list.
Accept / Cancel
Press Accept to confirm the changes or Cancel to return previous
settings.
1. Accept does not compile the changes, you must go to Status -> Save/Load to apply the
new settings. Please refer to the chapter 4.1 for more detail.
2. The Access Point that you would like to extend the wireless area must enter your Access
Point’s MAC address. Not all Access Point supports this feature.
6.1.4 Client Router Mode
Wireless Mode
The wireless mode supports 802.11b/g/n mixed modes. It is
compatible with the most common known wireless band.
SSID
Specify the SSID if known. SSID text box will be automatically fill
in when select an AP in the Site Survey.
Site Survey
Using Site Survey to scan nearby APs and then select the AP to
establish the connection.
Prefer BSSID
Specify the MAC address if known. Prefer BSSID text box will be
automatically fill in when select an AP in the Site Survey.
Wireless Security
Please refer to the chapter 6.2 for details.
Accept / Cancel
Press Accept to confirm the changes or Cancel to return previous
settings.
Accept does not compile the changes, you must go to Status -> Save/Load to apply the new
settings. Please refer to the chapter 4.1 for more detail.
Profile
After Site Survey, webpage will display all nearby area’s Access
Point. Click the BSSID if you would like to connect with it.
Wireless Security
Please refer to the Wireless Security section.
Refresh
Press Refresh to scan again.
If the Access Point is suppressed its own SSID, SSID section will be blank, the SSID must be
filled in manually.
6.2 Wireless Security Settings
Wireless Security Settings section will guide you to the entire Security modes configuration:
WEP, WPA-PSK, WPA2-PSK, WPA-PSK Mixed, WPA, WPA2, and WPA Mixed.
We strongly recommend that uses WPA2-PSK as your security settings.
6.2.1 WEP
Security Mode
Select WEP from the drop down list to begin the configuration.
Auth Type
Select Auth Type in Open System or Shared.
Input Type
Select Input Type in Hex or ASCII.
Key Length
Select Key Length in 64/128/152 bit password length.
Default Key
Select the default index key for wireless security.
Key1
Specify password for security key index No.1.
Key2
Specify password for security key index No.2.
Key3
Specify password for security key index No.3.
Key4
Specify password for security key index No.4.
802.11n does not allow WEP/WPA-PSK/WPA-PSK TKIP security mode. The date rate will drop
from 802.11n to 802.11g.
6.2.2 WPA-PSK
Security Mode
Select WPA-PSK from the drop down list to begin the
configuration.
Encryption
Select Both, TKIP or AES for Encryption type.
Passphrase
Specify the security password.
Group Key Update
Interval
Specify Group Key Update Interval time.
802.11n does not allow WEP/WPA-PSK/WPA-PSK TKIP security mode. The date rate will drop
from 802.11n to 802.11g.
6.2.3 WPA2-PSK
Security Mode
Select WPA2-PSK from the drop down list to begin the
configuration.
Encryption
Select Both, TKIP or AES for Encryption type.
Passphrase
Specify the security password.
Group Key Update
Interval
Specify Group Key Update Interval time.
802.11n does not allow WEP/WPA-PSK/WPA-PSK TKIP security mode. The date rate will drop
from 802.11n to 802.11g.
6.2.4 WPA-PSK Mixed
Security Mode
Select WPA-PSK Mixed from the drop down list to begin the
configuration.
Encryption
Select Both, TKIP or AES for Encryption type.
Passphrase
Specify the security password.
Group Key Update
Interval
Specify Group Key Update Interval time.
Uses WPA-PSK Mixed can allow multiple security modes at the same time.
802.11n does not allow WEP/WPA-PSK/WPA-PSK TKIP security mode. The date rate will drop
from 802.11n to 802.11g.
6.2.5 WPA
Security Mode
Select WPA from the drop down list to begin the configuration.
Encryption
Select Both, TKIP or AES for Encryption type.
Radius Server
Specify Radius Server IP Address.
Radius Port
Specify Radius Port number, the default port is 1812.
Radius Secret
Specify Radius Secret that is given by the Radius Server.
Group Key Update
Interval
Specify Group Key Update Interval time.
802.11n does not allow WEP/WPA-PSK/WPA-PSK TKIP security mode. The date rate will drop
from 802.11n to 802.11g.
6.2.6 WPA2
Security Mode
Select WPA2 from the drop down list to begin the configuration.
Encryption
Select Both, TKIP or AES for Encryption type.
Radius Server
Specify Radius Server IP Address.
Radius Port
Specify Radius Port number, the default port is 1812.
Radius Secret
Specify Radius Secret that is given by the Radius Server.
Group Key Update
Interval
Specify Group Key Update Interval time.
802.11n does not allow WEP/WPA-PSK/WPA-PSK TKIP security mode. The date rate will drop
from 802.11n to 802.11g.
6.2.7 WPA Mixed
Security Mode
Select WPA Mixed from the drop down list to begin the
configuration.
Encryption
Select Both, TKIP or AES for Encryption type.
Radius Server
Specify Radius Server IP Address.
Radius Port
Specify Radius Port number, the default port is 1812.
Radius Secret
Specify Radius Secret that is given by the Radius Server.
Group Key Update
Interval
Specify Group Key Update Interval time.
802.11n does not allow WEP/WPA-PSK/WPA-PSK TKIP security mode. The date rate will drop
from 802.11n to 802.11g.
6.3 Wireless Advanced Settings
Data Rate
Select Data Rate from the drop down list. Data rate will affect the
efficiency of the throughput. If the data rate is set to a small
number, the lower through will get but it can transmit to longer
distance.
Transmit Power
Select Transmit Power to increase or decrease Transmit Power.
Higher transmit power will sometimes cause unable to connect to
the network. On the other hand, the lower transmit power will
cause client unable to connect to the device.
RTS/CTS Threshold
Specify Threshold package size for RTC/CTS. Using small number
of the threshold will cause RTS/CTS packets to be sent more often
to consuming more of the available bandwidth. In addition, if the
heavy load traffic occurs, the wireless network can be recovered
easily from interferences or collisions.
Distance
Specify distance rage between AP and Clients. Longer distance
may lose high connection speed.
Short GI
Short GI is improved of 802.11n and 802.11a/g. It can increase
10% of the internet speed during the data transmission. For
example, the 802.11a/g’s GI is 800us, the short GI will be 400us.
Aggregation
Aggregation is to merge the typical size of data’s header to one
data. It is useful for the small size but larger amount packets.
Wireless Traffic
Shaping
Place a Check to enable Wireless Traffic Shaping function.
Incoming Traffic Limit
Specify the wireless transmission speed for downloading.
Outgoing Traffic Limit
Specify the wireless transmission speed for uploading.
Accept / Cancel
Press Accept to confirm the changes or Cancel to return previous
settings.
1. Changing Wireless Advanced Settings may cause insufficient wireless connection quality.
Please remain all settings as default unless you have acknowledged all changing that you
have made.
2. Accept does not compile the changes, you must go to Status -> Save/Load to apply the
new settings. Please refer to the chapter 4.1 for more detail.
6.4 Wireless MAC Filter
Wireless MAC Filters is used to Allow or Deny wireless clients, by their MAC addresses,
accessing the Network. You can manually add a MAC address to restrict the permission to
access ENH202. The default setting is Disable Wireless MAC Filters.
0.
ACL Mode
ACL Mode can help to deny or allow certain Client to access the
network. Select Disable, Deny MAC in the list or Allow MAC in the
list from the drop down list.
MAC Address Filter
Specify the MAC address manually.
Add
Press Add to add the MAC address in the table.
Apply
Press Apply to apply the changes.
6.5 WDS Link Settings
WDS Link Settings is used to establish a connection between Access Points but the device is
not losing Access Point function. AP has WDS function can extend the wireless coverage and
allow LANs to communicate each other.
MAC Address
Enter the Access Point’s MAC address that you would like to
extend the wireless area.
Mode
Select Disable or Enable from the drop down list.
Accept / Cancel
Press Accept to confirm the changes or Cancel to return previous
settings.
Accept does not compile the changes, you must go to Status -> Save/Load to apply the new
settings. Please refer to the chapter 4.1 for more detail.
The Access Point that you would like to extend the wireless area must enter your Access
Point’s MAC address. Not all Access Point supports this feature.
7 LAN Setup
This section will guide you to setup the Local Area Network (LAN) settings
7.1 IP Settings
This section is only available for Non-Router Mode. IP Settings allows you to LAN port IP
address of the ENH202.
IP Network Setting
Select Radio button for Obtain an IP address automatically or
Specify an IP address.
IP Address
Specify LAN port IP address.
IP Suet Mask
Specify Subnet Mask.
Default Gateway
Specify Default Gateway
Primary DNS
Specify Primary DNS
Secondary DNS
Specify Secondary DNS
Accept / Cancel
Press Accept to confirm the changes or Cancel to return previous
settings.
1. Obtain an IP address automatically is not a DHCP server. It means automatically get IP
address when device connected to a device which has DHCP server.
2. Changing LAN IP Address will change LAN Interface IP address. Webpage will automatically
redirect to the new IP address after Apply.
7.2 Spanning Tree Settings
Spanning Tree Status
Select the Radio button to On or Off Spanning Tree function.
Bridge Hello Time
Specify Bridge Hello Time in second.
Bridge Max Age
Specify Bridge Max Age in second.
Bridge Forward Delay
Specify Bridge Forward Delay in second.
Priority
Specify the Priority number. Smaller number has greater priority.
Accept / Cancel
Press Accept to confirm the changes or Cancel to return previous
settings.
Accept does not compile the changes, you must go to Status -> Save/Load to apply the new
settings. Please refer to the chapter 4.1 for more detail.
8 Router Settings
This section is only available for AP Router Mode and Client Router Mode.
8.1 WAN Settings
There are four different types of WAN connection: Static IP, DHCP, PPPoE and PPTP. Please
contact your ISP to select the connection type.
8.1.1 Static IP
Select Static IP in WAN connection if your ISP gives all the information about IP address,
Subnet Mask, Default Gateway, Primary DNS and Secondary DNS.
Internet Connection
Type
Select Static IP to begin configuration of the Static IP connection.
Account Name
Specify Account Name that is provided by ISP.
Domain Name
Specify Domain Name that is provided by ISP.
MTU
Specify the Maximum Transmit Unit size. Suggest remain in Auto.
IP Address
Specify WAN port IP address.
IP Subnet Mask
Specify WAN IP Subnet Mask.
Gateway IP Address
Specify WAN Gateway IP address.
Primary DNS
Specify Primary DNS IP.
Secondary DNS
Specify Secondary DNS IP.
Discard Ping on WAN
Place a Check to Enable or Disable ping from WAN.
Accept / Cancel
Press Accept to confirm the changes or Cancel to return previous
settings.
Accept does not compile the changes, you must go to Status -> Save/Load to apply the new
settings. Please refer to the chapter 4.1 for more detail.
If the router's MTU is set too high, packets will be fragmented downstream. If the router's
MTU is set too low, the router will fragment packets unnecessarily and in extreme cases may
be unable to establish some connections. In either case, network performance can suffer.
8.1.2 DHCP (Dynamic IP)
Select DHCP as your WAN connection type to obtain your IP address automatically. You will
need to enter Account Name as your hostname and DNS (Optional).
Internet Connection
Type
Select DHCP to begin configuration of the DHCP connection.
Account Name
Specify Account Name that is provided by ISP.
Domain Name
Specify Domain Name that is provided by ISP.
MTU
Specify the Maximum Transmit Unit size. Suggest remain in Auto.
Get Automatically
From ISP
Select the Radio button for get the DNS automatically from DHCP
server.
Use These DNS Servers Select the Radio button for setup the Primary DNS and
Secondary DNS servers manually.
Discard Ping on WAN
Place a Check to Enable or Disable ping from WAN.
Accept / Cancel
Press Accept to confirm the changes or Cancel to return previous
settings.
Accept does not compile the changes, you must go to Status -> Save/Load to apply the new
settings. Please refer to the chapter 4.1 for more detail.
If the router's MTU is set too high, packets will be fragmented downstream. If the router's
MTU is set too low, the router will fragment packets unnecessarily and in extreme cases may
be unable to establish some connections. In either case, network performance can suffer.
8.1.3 PPPoE (Point-to-Point Protocol over Ethernet)
Select PPPoE as your WAN connection type if your ISP provides Username and Password.
PPPoE is a DSL service and please remove your PPPoE software from your computer, the
software is not worked in ENH202.
Internet Connection
Type
Select PPPoE to begin configuration of the PPPoE connection.
MTU
Specify the Maximum Transmit Unit size. Suggest remain in Auto.
Login
Specify the Username that is given by your ISP.
Password
Specify the Password that is given by your ISP.
Service Name
Specify the Service Name that is given by your ISP.
Connect on Demand
Select the Radio button to specify the maximum idle time.
Internet connection will disconnect when it reach the maximum
idle time, but it will automatically connect when user tries to
access the network.
Keep Alive
Select the Radio button to keep internet connection always on.
Specify the redial period once the internet lose connection.
Get Automatically
From ISP
Select the Radio button for get the DNS automatically from DHCP
server.
Use These DNS Servers Select the Radio button for setup the Primary DNS and
Secondary DNS servers manually.
Discard Ping on WAN
Place a Check to Enable or Disable ping from WAN.
Accept / Cancel
Press Accept to confirm the changes or Cancel to return previous
settings.
Accept does not compile the changes, you must go to Status -> Save/Load to apply the new
settings. Please refer to the chapter 4.1 for more detail.
If the router's MTU is set too high, packets will be fragmented downstream. If the router's
MTU is set too low, the router will fragment packets unnecessarily and in extreme cases may
be unable to establish some connections. In either case, network performance can suffer.
8.1.4 PPTP (Point-to-Point Tunneling Protocol)
Select PPTP as your WAN connection type if your ISP provides information about IP Address,
Subnet Mask, Default Gateway (Optional), DNS (Optional), Server IP, Username, and Password.
Internet Connection
Type
Select PPTP to begin configuration of the PPTP connection.
MTU
Specify the Maximum Transmit Unit size. Suggest remain in Auto.
IP Address
Specify WAN port IP address.
IP Subnet Mask
Specify WAN IP Subnet Mask.
Gateway IP Address
Specify WAN Gateway IP address.
PPTP Server
Specify PPTP Server IP address.
Username
Specify the Username that is given by your ISP.
Password
Specify the Password that is given by your ISP.
Connect on Demand
Select the Radio button to specify the maximum idle time.
Internet connection will disconnect when it reach the maximum
idle time, but it will automatically connect when user tries to
access the network.
Keep Alive
Select the Radio button to keep internet connection always on.
Specify the redial period once the internet lose connection.
Get Automatically
From ISP
Select the Radio button for get the DNS automatically from DHCP
server.
Use These DNS Servers Select the Radio button for setup the Primary DNS and
Secondary DNS servers manually.
Discard Ping on WAN
Place a Check to Enable or Disable ping from WAN.
Accept / Cancel
Press Accept to confirm the changes or Cancel to return previous
settings.
Accept does not compile the changes, you must go to Status -> Save/Load to apply the new
settings. Please refer to the chapter 4.1 for more detail.
If the router's MTU is set too high, packets will be fragmented downstream. If the router's
MTU is set too low, the router will fragment packets unnecessarily and in extreme cases may
be unable to establish some connections. In either case, network performance can suffer.
8.2 LAN Settings (Router Mode)
IP Address
Specify LAN port IP address.
IP Subnet Mask
Specify LAN IP Subnet Mask.
WINS Server IP
Specify WINS Server IP.
Use Router As DHCP
Server
Place a Check to enable DHCP server.
Starting IP Address
Specify DHCP server starting IP address.
Ending IP Address
Specify DHCP server ending IP address.
WINS Server IP
Specify the WINS Server IP address.
Accept / Cancel
Press Accept to confirm the changes or Cancel to return previous
settings.
Accept does not compile the changes, you must go to Status -> Save/Load to apply the new
settings. Please refer to the chapter 4.1 for more detail.
8.3 VPN Pass Through
VPN Pass Through is used to allow certain protocol to be tunneled through an IP network
such as PPTP and L2TP or implement secure exchange of packets at the IP Layer such as IPSec.
PPTP Pass Through
Place a Check to enable PPTP protocol passes through WAN.
L2TP Pass Through
Place a Check to enable L2TP protocol passes through WAN.
IPSec Pass Through
Place a Check to enable IPSec protocol passes through WAN.
Accept / Cancel
Press Accept to confirm the changes or Cancel to return previous
settings.
Accept does not compile the changes, you must go to Status -> Save/Load to apply the new
settings. Please refer to the chapter 4.1 for more detail.
8.4 Port Forwarding
Port Forwarding is used to allow a public service such as Web Server, Mail Server, and FTP
server to be set up. For example: Set up a Web Server on your computer with port number
8080. Visitor on the internet can access your Web Server by entering WAN Port IP with port
number 8080. If your WAN Port IP is 192.168.5.1, then visitor must enter
http://192.168.5.1:8080. To find out more the well known port numbers please search the
internet.
Add Entry
Press Add Entry to add a rule of Port Forwarding.
Accept
Press Accept to confirm the changes.
Accept does not compile the changes, you must go to Status -> Save/Load to apply the new
settings. Please refer to the chapter 4.1 for more detail.
Service Name
Specify a name for current Port Forwarding rule.
Protocol
Select a protocol from drop down list: Both, TCP and UDP.
Starting Port
Specify Starting Port number.
Ending Port
Specify Ending Port number.
IP Address
Specify IP address.
Save / Cancel
Press Save to apply the changes or Cancel to return previous
settings.
8.5 DMZ
Enable DMZ will expose your network computer to the internet. This feature may be used in
some circumstance such as Internet Gaming or Video Conference. DMZ will forward all the
ports to one PC at the same time. This PC would be easily to attack because DMZ opens all
the ports to one certain PC.
DMZ Hosting
Select Enable or Disable DMZ from drop down list.
DMZ Address
Specify an IP address of DMZ.
Accept / Cancel
Press Accept to confirm the changes or Cancel to return previous
settings.
Accept does not compile the changes, you must go to Status -> Save/Load to apply the new
settings. Please refer to the chapter 4.1 for more detail.
9 Management Settings
Management section is on the navigation drop-down menu. You will then see seven options:
administration, management VLAN, SNMP settings, backup/restore settings, firmware
upgrade, time settings, and log. Each option is described below.
9.1 Administration
Click on the Administration link under the Management menu. This option allows you to
create a user name and password for the device. By default, this device is configured with a
user name and password admin. For security reasons it is highly recommended that you
create a new user name and password.
Name
Specify Username for login.
Password
Specify a Password for login
Confirm Password
Re-enter the Password for confirmation.
Remote Management
Select the Radio button to Enable or Disable Remote
Management.
Remote Upgrade
Select the Radio button to Enable or Disable Remote Upgrade.
Remote Management
Port
Specify the Port number for Remote Management. For example:
If you specify the Port number is 8080, then you will need to
enter following http://<IP address>:8080 to access the web
interface.
Save/Apply / Cancel
Press Save/Apply to apply the changes or Cancel to return
previous settings.
Press Save/Apply will change the setting immediately. It will not be able to undo the action.
9.2 Management VLAN
Click on the Management VLAN link under the Management menu. This option allows you
to assign a VLAN tag to the packets. A VLAN is a group of computers on a network whose
software has been configured so that they behave as if they were on a separate Local Area
Network (LAN). Computers on VLAN do not have to be physically located next to one another
on the LAN
Management VLAN ID
If your network includes VLANs and if tagged packets need to
pass through the Access Point, specify the VLAN ID into this field.
If not, select the No VLAN tag radio button.
Accept / Cancel
Press Accept to confirm the changes or Cancel to return previous
settings.
1. If you reconfigure the Management VLAN ID, you may lose connection to the ENH202.
Verify DHCP server can support the reconfigured VLAN ID, and then re-connect to the new IP
address.
2. Accept does not compile the changes, you must go to Status -> Save/Load to apply the
new settings. Please refer to the chapter 4.1 for more detail.
9.3 SNMP Settings
Click on the SNMP Settings link under the Management menu. This is a networking
management protocol used to monitor network-attached devices. SNMP allows messages
(called protocol data units) to be sent to various parts of a network. Upon receiving these
messages, SNMP-compatible devices (called agents) return data stored in their Management
Information Bases.
SNMP Enable/Disable
Select the Radio button to Enable or Disable SNMP function.
Contact
Specify the contact details of the device.
Location
Specify the location of the device.
Community Name
Specify the password for access the SNMP community for read
only access.
Community Name
Specify the password for access the SNMP community for read
and write access.
Trap Destination IP
Address
Specify the IP address that will receive the SNMP trap.
Trap Destination
Community Name
Specify the password of the SNMP trap community.
Save/Apply / Cancel
Press Save/Apply to apply the changes or Cancel to return
previous settings.
Press Save/Apply will change the setting immediately. It will not be able to undo the action.
9.4 Backup/Restore Settings
Click on the Backup/Restore Setting link under the Management menu. This option is used
to save the current settings of the device in a file on your local disk or load settings on to the
device from a local disk. This feature is very handy for administrators who have several devices
that need to be configured with the same settings.
Save A Copy of
Current Settings
Click on Backup to save current configured settings.
Restore Saved Settings ENH202 can restore a previous setting that has been saved. Click
from a File
on Browse to select the file and Restore.
Revert to Factory
Default Settings
Click on Factory Default button to reset all the settings to the
default values.
9.5 Firmware Upgrade
Click on the Firmware Upgrade link under the Management menu. This page is used to
upgrade the firmware of the device. Make sure that downloaded the appropriate firmware
from your vendor.
Upgrade process may take few minutes, please do not power off the device and it may cause
the device crashed or unusable. ENH202 will restart automatically once the upgrade is
completed.
9.6 Time Settings
Click on the Time Settings link under the Management menu. This page allows you to
configure the time on the device. You may do this manually or by connecting to a NTP server.
Manually Set Date and
Time
Manually setup the date and time.
Automatically Get
Date and Time
Specify the Time Zone from the drop down list and Place a Check
to specify the IP address of the NTP Server manually or uses
default NTP Server.
Save/Apply / Cancel
Press Save/Apply to apply the changes or Cancel to return
previous settings.
Press Save/Apply will change the setting immediately. It will not be able to undo the action.
9.7 Log
Click on the Log link under the Management menu. The Log page displays a list of events
that are triggered on the Ethernet and Wireless interface. This log can be referred when an
unknown error occurs on the system or when a report needs to be sent to the technical
support department for debugging purposes.
Syslog
Select Enable or Disable Syslog function from the drop down list.
Log Server IP Address
Specify the Log Server IP address.
Local Log
Select Enable or Disable Local Log service.
Save/Apply / Cancel
Press Save/Apply to apply the changes or Cancel to return
previous settings.
Press Save/Apply will change the setting immediately. It will not be able to undo the action.
9.8 Diagnostics
Click on the Diagnostics link under the Management menu. This function allows you to
detect connection quality and trace the routing table to the target.
Target IP
Specify the IP address you would like to search.
Ping Packet Size
Specify the packet size of each ping.
Number of Pings
Specify how many times of ping.
Start Ping
Press Start Ping to begin.
Traceroute Target
Specify an IP address or Domain name you would like to trace.
Start Traceroute
Press Start Traceroute to begin.
10 Network Configuration Example
This chapter describes the role of the ENH202 with 4+1 modes. The Access Point mode’s
default configuration is a central unit of the wireless network or as a root device of the wired
environment. Repeater mode and Mesh network mode need future configuration.
10.1 Access Point
Access Point
Step1
Login to the web-based configuration interface with default IP
192.168.1.1
Step2
Select your country or region’s regulation.
Step3
Use site survey to scan channels that have been used in nearby
area.
Step4
Select channel with less interferences.
Step5
Specify the SSID for your broadcast SSID and you can also
configure multiple SSID at the same time.
Step6
Verify VLAN identifier to separate services among clients
Step7
Setup the authentication settings.
Step8
Apply to process all the configurations.
For more advanced settings, please refer to the previous chapters.
Wireless Client
Step1
Select wireless mode you would like to associate with.
Step2
Use site survey to scan nearby Access Point and select the certain
AP you would like to connect with or enter SSID manually.
Step3
Configure VLAN ID in your wireless device if available.
Step4
Select correct authentication type and password.
ENH202’s Access Point Mode does not provide DHCP server so the Wireless
Client IP address must configure manually at the same subnet in Local Area Network.
10.2 Client Bridge Mode
Client Bridge Mode functions like a wireless dongle. It must connect to an Access Point/AP
Router to join the network.
Please refer to the last section to check Access point’s configuration.
Client Bridge
Step1
Login to the web-based configuration interface with default IP
192.168.1.1
Step2
Select your country or region’s regulation.
Step3
Select Operation Mode to Client Bridge from System
Properties.
Step4
Use site survey to scan Access Points that are available in nearby
area.
Step5
Select the AP you would like to associate with.
Step6
Setup the authentication settings that match to the Access Point’s
setting.
Step7
Apply to process all the configurations.
Client Bridge’s IP setting must match to the Access Point’s subnet.
10.3 WDS Bridge Mode
Use this feature to link multiple APs in a network. All clients associated with any APs can
communicate each other like an ad-hoc mode.
WDS Bridge
Step1
Login to the web-based configuration interface with default IP
192.168.1.1
Step2
Select your country or region’s regulation.
Step3
Select Operation Mode to WDS Bridge from System
Properties.
Step4
Select channel you would like to use.
Step5
Setup the authentication settings
Step6
Setup WDS Link Settings.
Step7
Specify the AP’s MAC address you would like to connect with.
Step8
Press Apply to process all the configurations.
Each WDS bridge’s device must use the same Subnet, Wireless Mode, Wireless
Channel, and Security Setting.
10.4 Client Router
In the Client Router Mode, the ENH202 has DHCP Server build inside that allows many LANs
automatically generate an IP address to share the same Internet. Connect an AP/WISP
Wirelessly and connect to LANs via wired. Client Router Mode is act completely opposite to
the AP Router Mode.
Please refer to the last section to check Access point’s configuration.
Client Router
Step1
Login to the web-based configuration interface with default IP
192.168.1.1
Step2
Select your country or region’s regulation.
Step3
Select Operation Mode to Client Router from System
Properties.
Step4
Change your Local Area Network setting to Obtain an IP
Address Automatically.
Step5
Use site survey to scan Access Points that are available in nearby
area.
Step6
Select the AP you would like to associate with.
Step7
Setup the authentication settings that match to the Access Point’s
setting.
Step8
Setup your WAN connection type given by your Internet Service
Provider from WAN Settings.
Step9
Press Apply to process all the configurations.
Client Router’s IP setting must match to the Access Point’s subnet.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
Note: Country selection is not available in the US model.
Industry Canada statement:
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio
exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne
doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y
compris un brouillage susceptible de provoquer un fonctionnement indésirable.
IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
NOTE IMPORTANTE: (Pour l'utilisation de dispositifs mobiles)
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm
de distance entre la source de rayonnement et votre corps.
Europe – EU Declaration of Conformity
This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test
methods have been applied in order to prove presumption of conformity with the essential requirements of
the R&TTE Directive 1999/5/EC:
-
EN60950-1:2006 A11:2009
Safety of Information Technology Equipment
-
EN50385 : 2002
-
Generic standard to demonstrate the compliance of electronic and electrical apparatus with the basic
restrictions related to human exposure to electromagnetic fields (0 Hz - 300 GHz)
-
EN 300 328 V1.7.1: 2006-10
-
Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband Transmission systems; Data
transmission equipment operating in the 2,4 GHz ISM band and using spread spectrum modulation
techniques; Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive
EN 301 489-1 V1.8.1: 2008-04
Electromagnetic compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC)
standard for radio equipment and services; Part 1: Common technical requirements
-
EN 301 489-17 V2.1.1 2009-05
-
Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC)
standard for radio equipment and services; Part 17: Specific conditions for 2,4 GHz wideband transmission
systems and 5 GHz high performance RLAN equipment
This device is a 2.4 GHz wideband transmission system (transceiver), intended for use in all EU member states
and EFTA countries, except in France and Italy where restrictive use applies.
In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain
authorization to use the device for setting up outdoor radio links and/or for supplying public access to
telecommunications and/or network services.
This device may not be used for setting up outdoor radio links in France and in some areas the RF output
power may be limited to 10 mW EIRP in the frequency range of 2454 – 2483.5 MHz. For detailed information
the end-user should contact the national spectrum authority in France.
0560
Česky
[Czech]
Dansk
[Danish]
Deutsch
[German]
[Jméno výrobce] tímto prohlašuje, že tento [typ zařízení] je ve shodě se základními požadavky a dalšími
příslušnými ustanoveními směrnice 1999/5/ES.
Undertegnede [fabrikantens navn] erklærer herved, at følgende udstyr [udstyrets typebetegnelse]
overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Hiermit erklärt [Name des Herstellers], dass sich das Gerät [Gerätetyp] in Übereinstimmung mit den
grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG
befindet.
Eesti
Käesolevaga kinnitab [tootja nimi = name of manufacturer] seadme [seadme tüüp = type of equipment]
[Estonian]
vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele
sätetele.
English
Hereby, [name of manufacturer], declares that this [type of equipment] is in compliance with the
essential requirements and other relevant provisions of Directive 1999/5/EC.
Español
[Spanish]
Ελληνική
[Greek]
Français
[French]
Italiano
[Italian]
Latviski
[Latvian]
Lietuvių
[Lithuanian]
Nederlands
[Dutch]
Malti
[Maltese]
Magyar
[Hungarian]
Polski
[Polish]
Português
[Portuguese]
Slovensko
[Slovenian]
Slovensky
Por medio de la presente [nombre del fabricante] declara que el [clase de equipo] cumple con los
requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ [name of manufacturer] ΔΗΛΩΝΕΙ ΟΤΙ [type of equipment] ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ
ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.
Par la présente [nom du fabricant] déclare que l'appareil [type d'appareil] est conforme aux exigences
essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE.
Con la presente [nome del costruttore] dichiara che questo [tipo di apparecchio] è conforme ai requisiti
essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
Ar šo [name of manufacturer / izgatavotāja nosaukums] deklarē, ka [type of equipment / iekārtas tips]
atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.
Šiuo [manufacturer name] deklaruoja, kad šis [equipment type] atitinka esminius reikalavimus ir kitas
1999/5/EB Direktyvos nuostatas.
Hierbij verklaart [naam van de fabrikant] dat het toestel [type van toestel] in overeenstemming is met de
essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.
Hawnhekk, [isem tal-manifattur], jiddikjara li dan [il-mudel tal-prodott] jikkonforma mal-ħtiġijiet
essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC.
Alulírott, [gyártó neve] nyilatkozom, hogy a [... típus] megfelel a vonatkozó alapvetõ követelményeknek
és az 1999/5/EC irányelv egyéb elõírásainak.
Niniejszym [nazwa producenta] oświadcza, że [nazwa wyrobu] jest zgodny z zasadniczymi wymogami oraz
pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.
[Nome do fabricante] declara que este [tipo de equipamento] está conforme com os requisitos essenciais
e outras disposições da Directiva 1999/5/CE.
[Ime proizvajalca] izjavlja, da je ta [tip opreme] v skladu z bistvenimi zahtevami in ostalimi relevantnimi
določili direktive 1999/5/ES.
[Meno výrobcu] týmto vyhlasuje, že [typ zariadenia] spĺňa základné požiadavky a všetky príslušné
[Slovak]
Suomi
[Finnish]
ustanovenia Smernice 1999/5/ES.
[Valmistaja = manufacturer] vakuuttaa täten että [type of equipment = laitteen tyyppimerkintä]
tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden
ehtojen mukainen.
Svenska
[Swedish]
Härmed intygar [företag] att denna [utrustningstyp] står I överensstämmelse med de väsentliga
egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising