advertisement
TFT-LCD TV
Please READ this manual carefully before operating your TV, and retain it for future reference.
MODELS:
HL37E
HL42E
HL47E
HL52E
WARNING
RISK ELECTRIC SHOCK
DO NOT OPEN
WARNING : To reduce the risk of electric shock do not remove cover or back.
No user-serviceable parts inside refer service to qualified service personnel.
Safety of operators has been taken into consideration at the design and manufacture phase, but inappropriate operation may cause electric shock or fire. To prevent the product from being damaged, the following rules should be observed for the installation, use and maintenance of th product. Read the following safety instruction before starting the operation.
The User Manual uses the following symbols to ensure a safe operation and prevent any damage to operators or properties:
THIS SYMBOL INDICATES THAT HIGH VOLTAGE IS PRESENT
INSIDE. IT IS DANGEROUS TO MAKE ANY KIND OF CONTACT
WITH ANY INSIDE PART OF THIS PRODUCT.
THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT
OPERATING AND MAINTENANCE INSTRUCTIONS IN THE
LITERATURE ACCOMPANYING THE APPLIANCE.
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rule. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, use and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However ,there is no guarantee that interference with not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encourage to try to correct the interference by one or more of the following measures:
*Reorient or relocate the receiving antenna.
*Increase the separation between the equipment and receiver.
*Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
*Consult the dealer or an experienced radio/TV technician for help.
This device compiles with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may be not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
FCC CAUTION:
To assure continued compliance and possible undesirable interference, the provided ferrite cores must be used when connecting this plasma display to video equipment; and maintain at least 40cm spacing to other peripheral device.
CANADIAN NOTICE:
This Class B digital apparatus compiles with Canadian ICES-003.
2 TV LCD-TFT
IMPORTANT SAFETY INSTRUCTIONS
Read all of the instructions before using this appliance. When using this
appliance, always exercise basic safety precautions, including the following:
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer`s instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, PORTABLE CART WARNING
(symbol provided by RETAC)
or sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of
time.
14) Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the
S3126A
apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
15) WARNING-To Reduce The Risk Of Fire Or Electric Shock, Do Not Expose This Apparatus To Rain Or Moisture.
Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases,
shall be placed on the apparatus.
The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.
The mains plug is used as the disconnect device, remain it readily operable during the apparatus normal use.
Owner s Manual 3
SAVE THESE INSTRUCTIONS
Thank you for using our Haier product. This easy-to-use manual will guide you in getting the best use of your product. Remember to record the model and serial number. They are on label in back of the unit.
Model number serial number
Date of purchase
Staple your receipt to your manual. You will need it to obtain warranty service.
4 TV LCD-TFT
Introduction
Contents
War nin g . . . . . . . ... ... ... ... .. . . . . . . . . . . . . . . . . . . . . . . .
Saf ety I nst ruc tio ns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..
Introduction
Con tro ls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... ... ... ... ..
Connection Options . . . . . . . . . . . . . . . . . . . . . .............
Universal Remote Controller . ............ . . . . . . . . ......
Installation
Acc ess ori es . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... ... ... ..
Antenna Connection . . . . . . . . . . ..............................
VCR Connection. . . . . . . . . . . . . . . . . . . . . ............... ..
External A/V Source Setup . . . . .. . . . . ......................
DVD Connection . . . . . ...... . . . . . . . . . . . . . ................
DTV Connection.....................................................
Digital Audio Output . . . . . . . . . . . . . . . . . . . . ..............
PC Connection. . . . . . . . . . . . . . . . . . . . . . . ................
Monitor Out Setup . . . . . . . . . . . . . . . . . . . . ............... .
HDM I . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. ... ... ... ... ... .
Cable Sample.........................................................
Connecting Headphones . . . . . . . . . . . . . . . . . . . ....... .
Pow er so urc e.. ... ... ... ... .. . . . . . . . . . . . . . . . . . . . . . . . . .
Operation
Switching On/Off the TV set . . . . . ... . . . . . . . . . . . ... ...
Choose the Menu Language . . . . ..... .......................
Choose the input Source.........................................
Channel Menu
Automatic Scan. . . . . . . . . . . . . ............................. . .
Man ual S can . . . . ... ... ... ... .. . . . . . . . . . . . . . . . . . . . . . . .
Fine Tune................................................................
Edi t Pro gra m.. ... ... ... ... . . . . . . . . . . . . . . . . . . . . . . . . . ..
Rename .............. . . . . . . . . . . . . . . . . . . . . . . . . ..........
S elect the desired program . . . . . ........... ............ . . ..
S elect the desired sound . . .............. . . . ............ . . ..
Mute .............. . . . ............................................ . . ..
Video Menu
How to select picture modes.....................................
How to customize your own picture status .................
Asp ect R ati o Con tro l . . . . . . . . . . . . . . . . . . . . .. . . .. . . ..
Audio Menu
How to select audio modes......................................
How to customize your own audio status ..................
SAP Broadcasts Setup............................................
Time Menu
Date /Time setting...................................................
Timer on setting......................................................
Timer off setting......................................................
Sleep Timer setting.................................................
Time zone setting...................................................
Daylight Saving setting...........................................
Function Menu
Closed Captions.....................................................
CC mode...............................................................
NTSC Caption ........................................................
DTV Caption..........................................................
DTV Caption Style..................................................
OSD Timeout .........................................................
Blue screen ...........................................................
OSD transparency ..................................................
Adjust Menu
Screen Setup for PC mode......................................
Lock Menu
Parental Control rating and categories ......................
Others Functions
Bri ef In fo. . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... ... ... .. . .
Quick program view................................................
Setting up your remote control ................................
USB system .......................................................
Maintenance . . ... ... . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Product Specifications . . . . . . . . . . . . . . . . . . . . . . .. .
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . .
Warranty . . . . ... ... ... ... . . . . . . . . . . . . . . . . . . . .. . . . . . .
Owner s Manual 5
Controls
-This is a simplified representation of front panel.
-Here shown may be somewhat different from your TV.
Front panel controls
Introduction
POWER
CH CH+ VOL - VOL+ INPUT MENU
1.CH-/+ Program minus and plus, menu options
2.VOL-/+ Volume increase and decrease, menu reset and entry
3.INPUT: all input resouce display and OK confirm:
4..MENU
Menu display
5.POWER:Is used to activate the display or return to standby mode
6 TV LCD-TFT
Connection Options
Left side connetions
Antenna Input
Connect cable or antenna signals to the TV, either directly or through your cable box.
PC VIDEO Input
Connect the monitor output connector from a PC to the jack
S-Video Input
Connect S-Video out from an S-VIDEO device to the
S-VIDEO input.
HDMI1 connect a signal to
HDMI/DVI.
DVI/PC Audio Input
Connect the audio out from the external device, used while using a DVI to HDMI connector.
Power Cord Socket
This TV operates on AC power.
The voltage is indicated on the Specifications page.
Never attempt to operate the TV on DC power
HDMI2 connect a signal to
HDMI/DVI.
DVD/DTV Input
(Component )
Connect a component video device to these jacks.
VIDEO Input
Connects the video signal from a video device.
Earphone jack:
Earphone audio output terminal.
Power Cord Socket
This TV operates on AC power.
The voltage is indicated on the Specifications page.
Never attempt to operate the TV on DC power
Introduction
Remote Controller
- The remote controller cannot be operated unless the batteries are properly loaded.
- When using the remote control, aim it at the remote control sensor on the TV.
Function introduction
POWER
Turns your TV or any other programmed equipment on or off, depending on mode.
CH.LIST
Open the channel list.
USB
Press to enter USB signal
TV
Press to enter TV signal
P.MODE
Selects the picture appropriate for the program`s character.
CC(closed caption)
Select a closed caption:
CC MUTE, CC ON, CC OFF.
TIME
Shows time.
MENU
Brings up the main menu to the screen.
EXIT
Clears all on-screen displays and returns toTV viewing from any menu.
MUTE
Switches the sound on or off
ARC
(Aspect Ratio Control)
Changes the aspect ratio.
VOLUME UP/DOWN
Increases/decreases the sound level.
Numeric buttons press to change the channel.
- button
Press to select additional channels
(digital and analog) being broadcast by the same station.
For example, to select channel
“54-3”, press “54”, then press “-” and “3”.
C T
M O M O
F V..L
II
T
A O II S T
TIM
E
TIM
E
TV USB
Press the SELECT button repeatedly to select one of the system modes in which the remote control can be used.
When the desired device is selected, the corresponding
LED lights on 5seconds.
FAVORITE
Open the favorite channel list.
AUDIO.LIST
Open the audio channellist.
ZOOM( only SUB System)
To enlarge or lessen the picture
HOTKEY ( only SUB System)
/ Rewind / Fast
/ backward /Forward
Play
II Pause
RETURN
S.MODE
Selects the sound appropriate for the program's character.
FREEZE
Freezes the currently-viewed picture, but audio continues.
Press FREEZE button again to resume the normal picture.
INPUT show the input source mode.
INFO
When you watch the TV, press the key, the information displays on bottom of the screen.
THUMBSTICK
(Up/Down/Left/Right/OK)
Allows you to navigate the on-screen menus and adjust the system settings to your preference.
SLEEP button
Displays the Sleep Timer option.
LIGHT
Press the light button, white LED will be ON, release this key, white LED will be OFF.
SAP
Selects MTS sound: Mono, Stereo, and SAP in Analog mode. Change the audio language in DTV mode.
CHANNEL UP/DOWN
Selects available channels
Q.VIEW
Switch the current channel to the last channel you have viewed.
Note: For DVD function see page 35.
8 TV LCD-TFT
External Equipment Connections
Accessories
C H H L
M O
FA AV L S S T A U U D O II S S T
HOTKEY
RETURN
TIM E
TIM
E
TFT-LCD TV
Please READ this manual carefully before operating your TV, and retain it for future reference.
Remote controller Owner`s manual
Alkaline battery(AAA) 2
Power cable
Installation
Antenna Connection
Generally speaking, to enjoy a clearer picture, we recommend that you use a CATV system or an outdoor antenna .In different places, the suitable antenna type and position are different.
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
Wall Antenna
Socket
RF Coaxial Wire (75 ohm)
Bronze Wire
VHF Antenna
UHF Antenna
Turn clockwise to tighten.
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
Outdoor
Antenna
Bronze Wire
Be careful not to bend the bronze wire when connecting the antenna.
To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly.
If the antenna needs to be split for two TV`s, install a 2-
Way Signal Splitter in the connections.
If the antenna is not installed properly, contact your dealer for assistance.
Owner s Manual 9
External Equipment Connections
NOTE: All cables shown are not included with the TV.
Choose Your Connection
There are several ways to connect your television, depending on the components you want to connect and the quality of the signal you want to achieve. The following are examples of some ways to connect your TV. Choose the connection which is best for you.
Installation
VCR connection
- To avoid picture noise (interference), leave an adequate distance between the VCR and TV
Connection Option 1
Set VCR output switch to channel 3 or 4 and then tune the TV to the same channel number.
Connection Option 2
1 . Connect the audio and video cables from the
VCR's output jacks to the TV input jacks, as shown in the figure.
When connecting the TV to VCR, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red).
If you connect an S-VIDEO output from VCR to the S-VIDEO input, the picture quality is improved; compared to connecting a regular
VCR to the Video input.
2 . Insert a video tape into the VCR and press
PLAY on the VCR. (Refer to the VCR owner`s manual.)
3 . Select the input source with using the
INPUT button on the remote control, and then press / button to select the source, press the OK button to confirm.
ANT IN
Y2
Y1
Pb2
Pb1
Pr2
Pr1
L
L
R
R S-VIDEO
AV OUT L R
VIDEO L R
10 TV LCD-TFT
Installation
External Equipment Connections
External A/V Source Setup
How to connect
Connect the audio and video cables from the external equipment's output jacks to the TV input jacks, as shown in the figure.
When connecting the TV to external equipment, match the jack colors (Video = yellow, Audio Left = white, and Audio
Right = red).
How to use
1. Select the input source with using the INPUT button on the remote control.
2. Press the / button to select the desired source.
3. Press the ok button to confirm
4. Operate the corresponding external equipment.
Y2
Y1
Pb2
Pb1
Pr2
Pr1
L
L
R
R S-VIDEO
AV OUT L R
VIDEO L R
Camcorder
Video Game Set
DVD connection
How to connect
1. Connect the DVD video outputs (Y, Pb/Cb, Pr/Cr) to the Y, Pb,
Pr jacks on the TV and connect the DVD audio outputs to the
YPbPr Audio IN jacks on the TV, as shown in the figure.
2. If your DVD only has an S-VIDEO output jack, connect this to the S-VIDEO input on the TV. as shown in the figure.
NOTE:
If your DVD player does not have component video output, use S-Video.
How to use
1. Turn on the DVD player, insert a DVD.
2. Use the INPUT button on the remote control to select YPbPr mode.
3. Press Play button on external equipment for program play.
4. Refer to the DVD player's manual for operating instructions.
Component Input ports
To get better picture quality, connect a DVD player to the component input ports as shown below.
Component ports on the TV
Video output ports on DVD player
Y Pb Pr
Y Pb Pr
Y B-Y R-Y
Y Cb Cr
Y P P
R
Y2
Y1
Pb2
Pb1
Pr2
Pr1
L
L
R
R S-VIDEO
AV OUT L R
VIDEO L R
Owner s Manual 11
Installation
External Equipment Connections
DTV connection
- This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive Digital signals from a digital set-top box or other digital external device, refer to the figure as shown below.
- This TV supports HDCP (High-bandwidth Digital Contents Protection) protocol for Digital Contents (480p,720p,1080i).
How to connect
Use the TV`s (Y, P
B
, P
R
) , PC or HDMI
jack for video connections, depending on your set-top box connector. Then, make the corresponding audio connections.
PC
Y2
Y1
Pb2
Pb1
Pr2
Pr1
L
L
R
R S-VIDEO
AV OUT L R
VIDEO L R
HDMI1
PC/DVI
AUDIO IN
OPTICAL
How to use
1. Turn on the digital set-top box. (Refer to the owner`s manual for the digital set-top box.)
2. Use INPUT on the remote control to select
YPbPr, PC,or HDMI source.
Signal
480i
480p
720p
1080i
YPbPr
Yes
Yes
Yes
Yes
HDMI/DVI
Yes
Yes
Yes
Yes
Digital Set-top Box
Audio Output
Send the TV`s audio to external audio equipment (stereo system) via the Audio Output (Optical) port.
How to connect
1. Connect one end of an optical cable to the TV Audio (Optical)
Output port.
2. Connect the other end of the optical cable to the digital audio (optical) input on the audio equipment.
See the external audio equipment instruction manual for operation.
Note: When connecting with external audio equipments, such as amplifers or speakers, please turn the TV speakers off.
Caution: Do not look into the optical output port.
Looking at the laser beam may damage
your vision.
12 TV LCD-TFT
PC/DVI
AUDIO IN
OPTICAL AC IN
Installation
External Equipment Connections
PC connection
How to connect
1 . To get the best picture quality, adjust the PC graphics card to 1024 x768 .
2 . Use the TV`s PC or DVI (Digital Visual Interface)Audio IN port for video connections, depending on your PC connector.
If the graphic card on the PC does not output analog and digital RGB simultaneously, connect only one of eitherPC IN o r DVI IN to display the PC on the TV.
If the graphic card on the PC does output analog and digital RGB simultaneously, set the TV to eithe r PC or set to Plug and Play automatically by the TV.)
DVI; (the other mode is
3 . Then, make the corresponding audio connection. If using a sound card, adjust the PC sound as required.
How to use
1 . Turn on the PC and the TV.
2. Turn on the display by pressing the POWER button on the TV's remote control.
3 . Use INPUT on the remote control to select PC or HDMI source.
4 . Check the image on your TV. There may be noise associated with the resolution, vertical pattern, contrast or brightness in PC mode. If noise is present, change the PC mode to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card.
NOTES:
1 Use a DVI cable.
2 Avoid keeping a fixed image on the TV's screen for a long period of time. The fixed image may become permanently imprinted on the screen.
3 The synchronization input form for Horizontal and Vertical frequencies is separate.
Resolution
Mode
PC
SPC
XGA
Resolution
640*480
800*600
1024*768
Frame frequency
(Hz)
60Hz
60Hz/75Hz
60Hz
75Hz
ANT IN HDMI2 PC HDMI1
PC/DVI
AUDIO IN
OPTICAL
Owner s Manual 13
Installation
External Equipment Connections
Monitor Out Setup
The TV has a special signal output capability which allows you to hook up a second TV or monitor.
Connect the second TV or monitor to the TV`s AV OUT.
See the Operating Manual of the second TV or monitor for further details regarding that device`s input settings.
Notes:
YPbPr, PC, HDMI,DTV input sources cannot be used for Monitor out.
When connecting with external audio equipments, such as amplifers or speakers, please turn the TV speakers off.
Y2
Y1
Pb2
Pb1
Pr2
Pr1
L
L
R
R S-VIDEO
AV OUT L R
VIDEO L R
HDMI
<When the source device(DVD player or Set Top Box) supports HDMI>
How To Connect
1. Connect the source device to HDMI port of this TV with an HDMI cable(not supplied with this product).
2. No separated audio connection is necessary.
How To Use
- If the source device supports Auto HDMI function, the output resolution of the source device will be automatically set to 1280x720p.
- If the source device does not support Auto HDMI, you need to set the output resolution appropriately.
To get the best picture quality, adjust the output resolution of the source device to 1280x720p.
- Select HDMI input source in input source option of Select Main source menu.
<When the source device(DVD player or Set Top Box) supports DVI>
How To Connect
1. Connect the source device to HDMI port of this TV with a HDMI-to-DVI cable(not supplied with this product).
2. A separated audio connection is necessary.
3. If the source device has an analog audio output connector, connect the source device audio output to DVI Audio In port located on the left side of HDMI port.
How To Use
- If the source device supports Auto DVI function, the output resolution of the source device will be automatically set to 1280x720p.
- If the source device does not support Auto DVI, you need to set the output resolution appropriately.
To get the best picture quality, adjust the output resolution of the source device to 1280x720p.
- Press the INPUT button to select HDMI input source in input source option of Select Main source menu.
14 TV LCD-TFT
Cable sample
Installation
HDMI Cable
(not supplied with the product)
HDMI to DVI Cable
(not supplied with the product)
Analog Audio Cable
(Stereo to RCA type)
(not supplied with the product)
Owner s Manual 15
External Equipment Connections
Connecting Headphones
You can connect a set of headphones to your set if you wish to watch a
TV programme without disturbing the other people in the room.
Plug a set of headphones into the 3.5mm mini-jack socket on the rear panel of the set.
HDMI1
PC/DVI
AUDIO IN
OPTICAL
Note
Prolonged use of headphones at a high volume may damage your hearing.
You will not receive sound from the speakers when you connect headphones to the system.
Installation
Power source
Wider Hole and Blade
AC Outlet
Polarized AC Cord Plug
(One blade is wider than the other.)
16 TV LCD-TFT
TO USE AC POWER SOURCE
Use the AC polarized line cord provided for operation on AC. Insert the AC cord plug into a standard polarized AC outlet.
NOTES:
Never connect the AC line cord plug to other than the specified voltage. Use the attached power cord only.
If the polarized AC cord does not fit into a nonpolarized AC outlet, do not attempt to file or cut the blade. It is the user`s responsibility to have an electrician replace the obsolete outlet.
If you cause a static discharge when touching the unit and the unit fails to function, simply unplug the unit from the AC outlet and plug it back in. The unit should return to normal operation.
Operation
Operation
-In the manual, the OSD (on screen display) may be different from your TV`s, because it is just an
example to help you with the TV operation.
-There are several options you might need to set up in order for your TV to work properly. Read the
instructions that follow.
Switching On/Off the TV set
1. First, connect power cord correctly, and then press POWER button on the remote control to turn on the TV.
2. Select the viewing source by using INPUT button on the remote control.
3. When finished using the TV, press the POWER button on the remote control. The TV reverts to standby mode.
4 . If you intend to be away on vacation, disconnect the power plug from the wall power outlet.
Note:
If the TV in power on , the screen show information according the type of input signal . the information will disappear. If there is no signal and blue screen in ON the screen enter in bluescreen and display No signal on top and center of the screen.
Choose the Menu Language
When you start using your set for the first time, you must select the language which will be used for displaying menus and indications.
Video
Audio
Time
A
B
C
Channel
Function
Lock
Menu Language English
CC Mode On
Basic Caption CC1
Advanced Caption Service1
Caption Type Basic
Caption Style
OSD Timeout Middle
Blue Screen On
OSD transparency Middle
English
Spanish
French
: Move cursor, /OK: Go to submenu, EXIT/ MENU: Exit main menu
1 Press the MENU button and then use / button to select the
Function menu.
2 Press the button and then use / button to select Menu
Language.
3 Press the button and then use / button to enter the list of available language. English Spanish or French
4 Select your language with the OK button to confirm you selection.
5 When you are satisfied with your choice, press the EXIT button to return to normal viewing or press MENU button to return to the previous menu.
Choose the Input source
- Change the picture source so you can watch your TV, cable TV, VCR, DVD, or any other devices that are
connected to your TV.
1. Press the INPUT button to enter the Select Main picture Source menu and then use ,
VIDEO2 , SVIDEO, COMPONENT 1, COMPONENT 2, PC, HDMI1, HDMI2,INNER
DVD.
2. Press the OK button to confirm.
3. Press INPUT button to return to TV viewing or press EXIT button to return to the previous menu.
Select Main Source
AIR TV
VIDEO1
VIDEO2
SVIDEO
COMPONENT1
COMPONENT2
PC
HDMI1
HDMI2
INNER DVD
Up/Down:Move Cursor
OK: Change MP Source
Right:Activale Source Name Edit Menu Note:
1. According to your connection device, you can change the name of every source.
2. In channel menu, if the Tuner item is set ting as Air or Cable, the source menu will display Air TV or Cable TV;
DVD
STB
PVR
Cable
Game
Owner s Manual 17
Operation
Channel menu
This TV set has three methods to set channels, which are respectively Auto Scan, manual Scan fine tune.
In this section, how to use the remote control to set channel is explained. You can also use buttons on the TV set to set channel.
A password is required to gain access to Channel menu if the Lock of Edit program menu is turned on.
Automatic Scan
- Automatically finds all channels available through antenna or cable inputs, and
stores them in memory on the All Channel List.
Note : Channel menu only available after selecting Air TV or Cable
TV in the input menu.
1 Press the MENU button and then use / button to select the
Channel menu.
2 Press the button and then use / button to select Tuner.
3 Press the button and then use / button to Select Cable or
Air mode.
4 Press the OK button
5 When you are satisfied with your choice, press MENU button to return to the previous menu.
6 Press the / button to select Auto Scan.
7 Press the button and press the OK button to start searching.
8 To cancel searching, press the OK button.
A
B
C
Video
Audio
Time
Channel
Function
Lock
Tuner Air
Auto Scan
Manual Scan
Fine Tune
Edit Program
Rename
Air
Cable
: Move cursor, /OK: Go to submenu, EXIT/ MENU: Exit main menu
A
B
C
Video
Audio
Time
Channel
Function
Lock
Tuner Air
Auto Scan
Manual Scan
Fine Tune
Edit Program
Rename
OK Cancel
Air Tuner Number: 47
Found: 1
: Move cursor, OK: Enter, MENU: Return to upper menu,
EXIT: Exit main menu
When Air is selected, the TV will detect antenna signals and will search for antenna TV (NTSC and ATSC) channels available in your local area.
When Cable is selected, the TV will detect cable company supplied signals and will search for cable TV (NTSC,ATSC, QAM modulated) channels available in your area.
18 TV LCD-TFT
Operation
Channel menu
Manual Scan
If excessive channel signals of unwanted programs are received in local area, manual search function is recommended.
1
Channel menu.
2
Press the MENU button and then use / button to select the
Press the button and then use / button to select Tuner.
A
B
C
Video
Audio
Time
Channel
Tuner Air
Auto Scan
Manual Scan
Fine Tune
Edit Program
Rename
Type
Channel NO
Frequency
3 Press the button and then use / button to Select Cable or Air mode.
4 Press the OK button.
5 When you are satisfied with your choice, press MENU button to return
Function
Lock
: Move cursor, /OK: Go to submenu, / ME NU: Return to upper menu,
EXIT: Exit main menu
Air
4
67.250MHz
0k
to the previous menu.
6 Press the / button to select Manual Scan.
7 Press the button and then use digital buttons to select channel number you want to add or delete.
8 Press the button to select OK item and press OK button to add for the channel number.
9 Press EXIT button to return to TV viewing or press MENU button to return to the previous menu.
Fine Tune (only in anolog signal )
1 Press the MENU button and then use / button to select the
Channel menu.
2 Press the / button to select Fine Tune.
3 Press the or OK button
4 Press the / button to tune.
5 Press EXIT button to return to TV viewing or press MENU button to return to the previous menu.
Video
Audio
Time
A
B
C
Channel
Function
Lock
Tuner Air
Auto Scan
Manual Scan
Fine Tune
Edit Program
Rename
For the tune of the analog channels
: Move cursor, /OK: Go to submenu, / ME NU: Return to upper menu,
EXIT: Exit main menu
Owner s Manual 19
Operation
Channel menu
Edit Program
You can create your own Favorite List. Use the
FAV.LiST butt on on the remote control when a channel is highlighted and then you can add or delete the channel to/from the Favorite List.
You can skip some channel;
You can lock some channel;
Video
A
B
C
Audio
Time
Channel
Tuner Air
Auto Scan
Manual Scan
Fine Tune
Edit Program
Rename
Music Ch No Name Fav Lock Skip
Function
Page 1/1 1 Press the MENU button and then use / button to select the
Channel menu.
2 Press the button and then use / button to select Edit Program.
Lock
3 Press the button. You will now see a screen filled with channel numbers.
: Move cursor, /OK: Go to submenu, / ME NU: Return to upper menu,
EXIT: Exit main menu
4 Use / / / button to select FAV., Lock or Skip item, and then use the OK button to confirm.
5 When you are satisfied with your choice, press MENU button to return to the previous menu or Press EXIT button to return to TV viewing.
Skip
After the programs are presetting, you can skip some programs so that to select your favorite channels only.
Lock
After the programs are presetting, you can lock some programs so that to select your favorite channels only.
Fav (Favorite)
Press the FAV.LiST
button open the favorite channel list, press channel and press OK button to confirm.
Rename
(only in anolog signal )
1 Press the MENU button and then use / button to select the
Channel menu.
2 Press the button and then use / button to select Rename.
3 Press the or OK button to enter the Submenu.
4 The cursor flashs, Use the digital button to select the letter, and
(Press the Q.VEIW button to delete the letter. )
5 When you are satisfied with your choice, press MENU button to return to the previous menu or Press EXIT button to return to TV viewing.
A
B
C
Video
Audio
Time
Channel
Function
Lock
Tuner Air
Auto Scan
Manual Scan
Fine Tune
Edit Program
Rename
Program No
Program Name
: Move cursor, /OK: Go to submenu, / ME NU: Return to upper menu,
EXIT: Exit main menu
20 TV LCD-TFT
Operation
Select the desired program
1
Using the CH+/- buttons.
Press the CH+ button to select a channel number in number increasing direction.
Press the CH- button to select a channel number in number decreasing direction.
(Note: If Skip is ON on one channel, press CH+/- button, the channel will not appear.)
Select the desired sound
Press the VOL-/+ or / buttons on the remote or the front of the TV set to adjust the volume level. The range is 0~100.
When the volume buttons are pressed the volume level is displayed automatically on the TV screen.
Volume
+ 21
Mute
When you need to pay attention to surrounded sounds, or there is a telephone calling you or there are some guests visiting you, the sound elimination (mute) function is very convenient.
1
Press the MUTE button on the remote control and " " type face will display on the screen. At this time, the sound of the TV set is turned off.
2
If you want to recover the sound, press the MUTE button again or directly press VOL+ button.
Owner s Manual 21
Video menu
The TV menu gives you an overview of the menus you can select.
Note: Depending on the input signal, one or more menu items may not be selectable.
How to select picture modes
The picture mode provides the pre-defined images settings. There are four settings: standard/ vivid /mild/custom .
Press P.MODE button repeatedly on the remote control to select the desired option(Standard/Vivid/Mild/Custom).
Standard: normal mode.
Vivid: mode of watching the movement of picture.
Mild: the effect of the picture is soft.
Custom: picture effect which you favorite.
Operation
How to customize your own picture status
1 Press the MENU button and then use / button to select the Video menu.
2 Press the button and then use / button to select the desired items.
3 Press the button and then use / button to adjust the setting.
4 When you are satisfied with your choice, press MENU button to return to
the previous menu or press the EXIT button to return to TV viewing.
Video
Audio
Time
A
B
C
Channel
Function
Lock
Mode Custom
Contrast 50
Brightness 50
Tint 0
Color 50
Sharpness 50
DNR Off
Color Temperature Standard
Black Stretch Off
Standard
Vivid
Mild
Custom
: Move cursor, /OK: Go to submenu, EXIT/ MENU: Exit main menu
Contrast
This will adjust the intensity of bright parts in the picture but keep the dark parts unchanged.
Brightness
This will adjust the light output of the complete picture, which will mainly affect the darker areas of the picture.
Tint
Allows you to select the color mix (Tint) of the picture.
Color
This will adjust the saturation level of the colors to suit your personal preference.
Sharpness
This will adjust the sharpness of fine details in the picture.
DNR (Digital Noise Reduction )
Automatically filters out and reduces the image noise and improves picture quality when receiving weak video signals.
Select Off/Weak/Medium /Strong according to the image noise.
Color temperature
This will increase or decrease Warm (red) and Cold (blue) colors to suit personal preferences.
Select Cold to give the white colors a blue tint, Standard to give the white colors a neutral tint, Warm to give the white colors a red tint.
Black Stretch
This will increase automatically the contrast rage.
Note:
Only when the item of mode is custom , the Contrast Brightness Tint color
Sharpness can be set by user . In other mode the value of them are preset by program .
22 TV LCD-TFT
Operation
Aspect Ratio Control
- Lets you choose the way an analog picture with a 4:3 aspect ratio is displayed on your TV with a 16:9 ratio picture format.
- Note: If a fixed image is displayed on the screen for a long time, it image may become imprinted on the screen and remain visible.
1 Press the ARC button the Aspect Ratio menu appearance on the screen.
2 Press the / button to select the desired picture format.
3 Press the OK button to confirm.
4:3 mode
Choose 4:3 when you want to view a picture with an original 4:3 aspect ratio, with gray bars appearing at both the left and right sides.
16:9 mode
Choose 16:9 when you want to adjust the picture horizontally, in a linear proportion to fill the entire screen.
Zoom 1
Choose Zoom 1 when you want to view the picture without any alteration. However, the top and bottom portions of the picture will be cropped.
Zoom 2
Choose Zoom 2 when you want the picture to be altered, both vertically extended and cropped. The picture taking a halfway trade off between alteration and screen coverage.
Subtitle
Choose Subtitle when you want to adjust the picture in a non-linear proportion, that is, more enlarged at top sides and no alteration , at bottom side.
PANORAMA
Choose PANORAMA when you want to enlarge the picture in correct proportion.
Note: When enlarging or reducing the picture size, the image may become distorted.
Notes
In TV, VIDEO1, VIDEO2,SVIDEO modes, all screen modes can be selected.
(16:9 Mode . Panorama . Zoom1 . Zoom2 . 4:3 Mode. Subtitle).
In YPbPr, HDMI modes, only 16:9 Mode, 4:3 modes, Zoom1 or Zoom2 can be selected.
In PC mode, only 16:9 Mode, 4:3 mode, dot by dot can be selected.
In DTV mode, only 16:9 Mode, 4:3 mode can be selected.
Owner s Manual 23
Audio menu
How to Select Audio modes
Press S.MODE button repeatedly on the remote control to select the desired option (Live/POP/Rock/Custom).
Custom A spare setting that can be adjusted to personal tastes.
Live Normal sound with moderate bass and treble setting.
POP Designed to reduce the bass and treble which enhances the voice for news programs.
Rock Enables extra bass and treble to enhance the movie experience.
Operation
How to Customize your own audio status
1 Press the MENU button and then use / button to select the Audio menu.
2
Press the button and then use / button to select the desired items.
3 Press the button and then use / button to adjust the setting.
4 When you are satisfied with your choice, press MENU button to return to
the previous menu or press the EXIT button to return to TV viewing.
Video
Audio
A
B
C
Time
Channel
Function
Lock
HeadPhone Volume 10
Volume 20
Balance 0
Equalizer Mode Custom
Digital Audio
AVL off
: Move cursor, /OK: Go to submenu, / ME NU: Return to upper menu,
EXIT: Exit main menu
Headphone volume
This controls the level of sound through the headphones.
Volume
This will adjust the sound output level.
Balance
This will adjust the output of the right and left speakers to obtain the best stereo reproduction for your listening position.
Equalizer Mode
This sound setting can be adjusted to suit your personal preference.
Digital Audio (only selectable with digital broadcast signals)
Make your selection of the source to which the device with digital audio input has been connected.
In addition to accepting audio input via Digital Audio In, the TV can output
Digital audio via the Optical connector to an external amplifier or receiver.
If your amplifier or receiver has a matching connector for Digital Audio In, you can connect it with a single cable to the TV`s Optical.
AVL ( Automatic volume control)
This will r educes the differences in volume level among broadcasters.
Video
Audio
A
B
C
Time
Channel
Function
Lock
HeadPhone Volume 10
Live POP Rock Custom
Volume 20
Balance 0
120Hz
500Hz
Equalizer Mode Custom 1.5KHz
5KHz
Digital Audio
AVL off
10KHz
: Move cursor, /OK: Go to submenu, / ME NU: Return to upper menu,
EXIT: Exit main menu
Video
Audio
Time
A
B
C
Channel
Function
Lock
HeadPhone Volume 10
Volume 20
Balance 0
Equalizer Mode Custom
Digital Audio Output Mode
Digital Audio
AVL off
Dolby Digital
PCM
: Move cursor, /OK: Go to submenu, / ME NU: Return to upper menu,
EXIT: Exit main menu
24 TV LCD-TFT
Audio menu
SAP Broadcasts Setup
- This TV can receive MTS stereo programs and SAP
(Secondary Audio Program) that accompanies the stereo program; if the station transmits an additional sound signal as well as the original one.
- When having selected SAP button on the remote control, this TV can only receive the signal when the TV station transmits the proper signals.
- Mono sound is automatically received if the broadcast is only in Mono; even
though Stereo or SAP has been selected.
- Select Mono if you want to listen to mono sound during stereo/SAP
broadcasting.
- Stereo or SAP can be received in a Analog channel.
1. Use the SAP button to select your desired MTS mode in a analog signal.
Each time you press the SAP button, Mono,Stereo, or SAP appear.
If other languages are available on the digital signal, select them with the
SAP button.
2. Press EXIT button to save and return to TV viewing.
Operation
Owner s Manual 25
Operation
Time menu
Date /Time setting
Setting the clock is necessary in order to use the various timer features of the TV. Also, you can check the time while watching the TV.
1 Press the MENU button and then use / button to select the Time menu.
2 Press the button and then use / button to select the Date/Time.
3 Press the button and then use / button to select the Mode:
Manual or Auto.
4 When you are satisfied with your choice, press MENU button to return to
the previous menu or press the EXIT button to return to TV viewing.
Video
Audio
Time
A
B
C
Channel
Function
Lock
Date/Time
Timer on
Timer Off
Sleep Timer 0 min
Time Zone Newfoundland
Daylight Saving On
Mode Manual Auto
Date 2004.12.31
Time 08 38 PM
: Move cursor, /OK: Go to submenu, / ME NU: Return to upper menu,
EXIT: Exit main menu
Timer on setting
Switch on automatically at the time you presetting.
1 Press the MENU button and then use / button to select the Time menu.
2 Press the button and then use / button to select the Timer On.
3 Press the button and then use / button to select the Mode:
Off, Once or Daily.
4 Press the OK button to confirm.
When selecting Once or Daily item, On time item will be active, press / button to set the desired level, press / button to button move cursor.
5 When you are satisfied with your choice, press MENU button to return to
the previous menu or press the EXIT button to return to TV viewing.
Video
Audio
A
B
C
Time
Channel
Function
Lock
Date/Time
Timer on
Timer Off
Sleep Timer 0 min
Time Zone Newfoundland
Daylight Saving On
Mode Off Once Daily
On time 08 38 PM
: Move cursor, /OK: Go to submenu, / ME NU: Return to upper menu,
EXIT: Exit main menu
Timer off setting
Switch off automatically at the time you presetting.
1
Press the MENU button and then use / button to select the Time menu.
2 Press the button and then use / button to select the Timer Off.
3 Press the button and then use / button to select the Mode:
Off, Once or Daily.
4 Press the OK button to confirm.
When selecting Once or Daily item, On time item will be active, press / button to set the desired level, press / button to button move cursor.
5 When you are satisfied with your choice, press MENU button to return to
the previous menu or press the EXIT button to return to TV viewing.
Video
Audio
Time
A
B
C
Channel
Function
Lock
Date/Time
Timer on
Timer Off
Sleep Timer 0 min
Time Zone Newfoundland
Daylight Saving On
Mode Off Once Daily
Off time 08 38 PM
: Move cursor, /OK: Go to submenu, / ME NU: Return to upper menu,
EXIT: Exit main menu
26 TV LCD-TFT
Operation
Time menu
Sleep Timer setting
The sleep timer automatically shuts off the TV after a preset time
(from 15 to 120 minutes).
1
Press the MENU button and then use / button to select the Time menu.
2 Press the button and then use / button to select the SleepTimer.
3 Press the button and then use / button to select the number of minutes.
Select 0Min, 15Min, 30Min, 60Min, 90Min, 120Min.
When the number of minutes you want is displayed on the screen, press the OK button. The time begins to count down from the number of minutes selected.
4 When you are satisfied with your choice, press MENU button to return to
the previous menu or press the EXIT button to return to TV viewing.
5 To cancel the set sleep timer:
Press the / button to select 0min.
You can use the SLEEP button also to select quickly the sleep timer.
Video
Audio
Time
A
B
C
Channel
Function
Lock
Date/Time
Timer On
Timer Off
Sleep Timer 0 min
Time Zone Newfoundland
Daylight Saving On
0 min
15min
30min
60min
90min
120min
: Move cursor, /OK: Go to submenu, / ME NU: Return to upper menu,
EXIT: Exit main menu
Time zone setting
(only available when date/time mode is set to Automatic)
This function allows you to select your local time zone.
Broadcasted time information will correct the clock display for your local time.
1 Press the MENU button and then use / button to select the Time menu.
2 Press the button and then use / button to select the Time Zone items.
3 Press the button and then use / button to adjust the setting.
4 When you are satisfied with your choice, press MENU button to return to
the previous menu or press the EXIT button to return to TV viewing.
Press the button and then use / button to select your viewing area time zone: Newfoundland, Atlantic, Eastern , Central , Mountain , Pacific , Alaska , Hawaii or Samoa.
Video
Audio
Time
A
B
C
Channel
Function
Lock
Date/Time
Timer on
Timer Off
Sleep Timer 0 min
Time Zone Newfoundland
Daylight Saving On
Newfoundland
Atlantic
Eastern
Central
Mountain
Pacific
Alaska
Hawaii
Samoa
: Move cursor, /OK: Go to submenu, / ME NU: Return to upper menu,
EXIT: Exit main menu
Daylight Saving setting
(only available when date/time mode is set to Automatic)
Daylight saving time is automatically set by specially broadcasted signals.
This menu item allows you to disable the automatic setting of daylight saving time. This is useful if you live in an area or state where daylight saving is not applied, but you receive channels from other areas where daylight saving signals are broadcasted.
1 Press / button to s elect Daylight Saving item.
2 Press the button t to select On for automatic clock correction for daylight saving time, based on specially broadcasted signals.
Select Off to disable automatic clock correction based on the specially broadcasted signals.
Video
Audio
Time
A
B
C
Channel
Function
Lock
Date/Time
Timer on
Timer Off
Sleep Timer 0 min
Time Zone Newfoundland
Daylight Saving On On
Off
: Move cursor, /OK: Go to submenu, / ME NU: Return to upper menu,
EXIT: Exit main menu
Owner s Manual 27
Operation
Function menu
Closed Captions
Closed captioning is a process which converts the audio portion of a television program into written words which then appear as subtitles on the television screen. Closed captions allow viewers to read the dialogue and narration of television programs.
Using Closed Captions
Captions are the subtitles of the dialogue and narration of television programs. For prerecorded programs, program dialogue can be arranged into captions in advance. Its possible to caption a live program by using a process called real-time captioning, which creates captions instantly. Real-time captioning is normally done by professional reporters using a machine shorthand system and computer for translation into English.
Captioning is an effective system for the hearing-impaired, and it can also aid in teaching language skills.
CC mode
1. Press the MENU button and then use / button to select the
Function menu.
2. Press the button to select the CC mode .
3. Press the button and then use / button to select the items:
( On , Off or On When mute .
)
4.
When you are satisfied with your choice, press MENU button to return to
the previous menu or press the EXIT button to return to TV viewing.
Video
Audio
A
B
C
Time
Channel
Function
Lock
Menu Language English
CC Mode On
Basic Caption CC1
Advanced Caption Service1
Caption Type Basic
Caption Style
OSD Timeout Middle
Blue Screen On
OSD transparency Middle
On off
On when mute
: Move cursor, /OK: Go to submenu, / ME NU: Return to upper menu,
EXIT: Exit main menu
Note : The captions do not always use correct spelling and grammar. Not all
TV programs and product commercials are made for broadcast with Closed
Caption information included. Refer to your area`s TV program listings for the TV channels and times of Closed Caption shows. The captioned programs are usually noted in the TV listings with service marks such as CC .
Basic Caption
This allows you to configure the way you choose to view the digital captioning.
1. Press the MENU button and then use / button to select the
Function menu.
2.
Press the button and then use / button to select Basic Caption.
3.
Press the button and then use / button to select caption: CC1 , CC2 ,
CC3 , CC4 , Text1 , Text2 , Text3 , or Text4 .
4. When you are satisfied with your choice, press MENU button to return to
the previous menu or press the EXIT button to return to TV viewing.
CAPTION
The term for the words that scroll across the bottom of the TV screen; usually the audio portion of the program provided for the hearing impaired.
TEXT
The term for the words that appear in a large black frame and almost cover the entire screen; usually messages provided by the broadcaster.
Video
Audio
Time
A
B
C
Channel
Function
Lock
Menu Language English
CC Mode On
Basic Caption CC1
Advanced Caption Service1
Caption Type Basic
Caption Style
OSD Timeout Middle
Blue Screen On
OSD transparency Middle
CC1
CC2
CC3
CC4
Text1
Text2
Text3
Text4
: Move cursor, /OK: Go to submenu, / ME NU: Return to upper menu,
EXIT: Exit main menu
Advanced Caption(
In DTV mode
)
This allows you to configure the way you choose to view the digital captioning.
Select one of the digital service channels made available by the caption provider.
There are 6 standard services. Service 1 is designated as the Primary
Caption Service. This service contains the verbatim, or near-verbatim captions for the primary language being spoken in the accompanying program audio.
Service 2 is designated as the Secondary Language Service. This service contains captions in a secondary language which are translations of the captions in the primary Caption Service. The other service subchannels are not pre-assigned. It is up to the discretion of the individual caption provider to utilize the remaining service channels.
Video
Audio
Time
A
B
C
Channel
Function
Lock
Menu Language English
CC Mode On
Basic Caption CC1
Advanced Caption Service1
Caption Type Basic
Caption Style
OSD Timeout Middle
Blue Screen On
OSD transparency Middle
Service1
Service2
Service3
Service4
Service5
Service6
: Move cursor, /OK: Go to submenu, / ME NU: Return to upper menu,
EXIT: Exit main menu
28 TV LCD-TFT
Operation
Caption Style (
In DTV mode
)
This allows you to modify how digital captions are displayed on your TV.
Select from the following options to change the visual characteristics of your TV`s digital captioning.
1. Press the MENU button and then use / button to select the Function menu.
2. Press the button and then use / button to select Caption Style.
3. Press the button and then use / button to set style as Custom.
4. Use / button to customize the Style, Font, etc., to your preference.
5. When you are satisfied with your choice, press MENU button to return to
the previous menu or press the EXIT button to return to TV viewing.
Style
Select this option to select the font style of caption display according to your own preference.
Press the / button to select Default, Custom, Style1, Style2, Style3,
Style4,Style5, Style6, Style7, Style8.
Press the OK button to confirm.
Size
Select this option to select the size of caption display according to your own preference.
Press the / button to select Default, Small, Normal or Large ,
Press the OK button to confirm.
Video
Audio
Time
A
B
C
Channel
Function
Lock
Menu Language English
CC Mode On
Basic Caption CC1
Advanced Caption Service1
Caption Type Basic
Caption Style
OSD Timeout Middle
Blue Screen On
OSD transparency Middle
Style Default
Size Default
Font Default
Text Color Default
Text Opacity Default
BG Color Default
BG Opacity Default
Preview
Closed Caption
: Move cursor, /OK: Go to submenu, / ME NU: Return to upper menu,
EXIT: Exit main menu
Font
Select this option to select the font of caption display according to your own preference.
Press the / button to select Default, Font1 Font2, Font3, Font4, Font5, Font6, Font7.
Press the OK button to confirm.
Text color
Select this option to select the text color or the opacity of the text box of caption display according to your own preference.
Select a color and one of the opacity options.
Text Opacity : Specify the opacity for the text color.
BG (Background) Color : Select a background color.
BG (Background) Opacity : Select the opacity for the background color.
OSD Timeout
1. Press the MENU button and then use / button to select the Function menu.
2. Press the button and then use / button to select OSD Timeout.
3. Press the button and then use / button to select short, middle or Long.
4. Press the OK button to confirm.
Blue screen
Select this option to select the character background color.
1. Press the MENU button and then use / button to select the Function menu.
2. Press the button and then use / button to select Blue screen .
3. Press the button and then use / button to select on or off.
4. Press the OK button to confirm.
Video
Audio
Time
A
B
C
Channel
Function
Lock
Menu Language English
CC Mode On
Basic Caption CC1
Advanced Caption Service1
Caption Type Basic
Caption Style
OSD Timeout Middle
Blue Screen On
OSD transparency Middle
Short
Middle
Long
: Move cursor, /OK: Go to submenu, / ME NU: Return to upper menu,
EXIT: Exit main menu
OSD transparency
1. Press the MENU button and then use / button to select the Function menu.
2. Press the button and then use / button to select OSD transparency .
3. Press the button and then use / button to select Low ,middle or High.
4. Press the OK button to confirm.
Video
Audio
Time
A
B
C
Channel
Function
Lock
Menu Language English
CC Mode On
Basic Caption CC1
Advanced Caption Service1
Caption Type Basic
Caption Style
OSD Timeout Middle
Blue Screen On
OSD transparency Middle
Low
Middle
High
: Move cursor, /OK: Go to submenu, / ME NU: Return to upper menu,
EXIT: Exit main menu
Owner s Manual 29
Operation
Adjust menu
Screen Setup for PC mode
- When RGB connect to PC input and select the PC, this function is used.
Adjustment for screen Position, Size, Phase, Reset
- Display PC Adjust Menu by pressing INPUT button then use / button to select the PC item.
Position : Adjust the screen position.
Size : Adjust the screen size.
Phase : Adjust the phase of Pixel clock.
Mode : there are two modes: Auto Sync and default
1 Press the MENU button and then use / button to select the
Adjust menu.
2 Press the button and then use / button to select the desired items.
3 Press the button and then use / button to adjust the setting.
4 When you are satisfied with your choice, press MENU button to return to
the previous menu or press the EXIT button to return to TV viewing.
Video
Audio
Time
Adjust
Function
Lock
H Size 20
H Position 20
V Size 20
V Position 20
Phase Adjust 18
Mode
: Move cursor, /OK: Go to submenu, EXIT/ MENU: Exit main menu
30 TV LCD-TFT
Operation
Lock Menu
Parental Control can be used to block specific channels, ratings and other viewing sources.
The Parental Control Function is used to block program viewing based on the ratings sent by the broadcasting station.
The default setting is to allow all programs to be viewed. Viewing can be blocked by choosing the type of the program and the categories.
It is also possible to block all program viewing for a time period. To use this function, the following must be done :
1. Set ratings and categories to be blocked.
2. Specify a password
3. Enable the lock
Parental Control rating and categories
Rating guidelines are provided by broadcasting stations. Most television programs and television movies can be blocked by TV Rating and/or Individual Categories. Movies that have been shown at the theaters or direct-to-video movies use the Movie Rating System (MPAA) only.
Ratings for Movies previously shown in theaters:
Movie Ratings :
NR (Permits all programs)
G (General audience)
PG (Parental guidance suggested)
PG-13 (Parents strongly cautioned)
R (Restricted)
NC-17 (No one 17 and under admitted)
X (Adult only)
If you set PG-13 : G and PG movies will be available , PG-13, R, NC-17 and X will be blocked.
Ratings for Television programs including made-for-TV movies :
TV-Y (All children)
TV-Y7 (Children 7 years older)
TV-G (General audience)
TV-PG (Parental guidance suggested)
TV-14 (Parents strongly cautioned)
TV-MA (Mature audience only)
TV Rating Children:
ALL (Age) (applies to TV-Y, TV-Y7)
FV (Fantasy Violence) (applies to TV-Y7)
TV Rating General:
ALL (Age) (applies to TV-G, TV-PG, TV-14, TV-MA)
D (Dialogue - sexual dialogue) (applies to TV-PG, TV-14)
L (Language - adult language) (applies to TV-PG, TV-14, TV-MA)
S (Sex - sexual situations) (applies to TV-PG, TV-14, TV-MA)
V (Violence) (applies to TV-PG, TV-14, TV-MA)
Owner s Manual 31
Operation
Lock setup
- Set up blocking schemes to block specific channels, ratings, and external viewing sources.
- A password is required to gain access to this menu.
1. Press the MENU button and then use / button to select the LOCK menu.
Then, press the button.
The TV is set up with the initial password 0-0-0-0 and security default password is 9-4-4-3.
2. Use the / button to choose from the right Lock Menu options.
Once the option is selected, change the settings to your preference.
Password: Change the password by inputting a new password twice.
Video
Audio
Time
A
B
C
Channel
Function
Lock
Password
Parental Lock On
MPAA Rating
Parental Guide
CA Eng Rating
CA Fren Rating
Input Password:
Confirm Password:
: Move cursor, /OK: Go to submenu, / ME NU: Return to upper menu,
EXIT: Exit main menu
Parental Lock:
1. P ress elect
2.
Press the button to select On or Off.
3.
Press the OK button to confirm.
Lock item.
Note: if the Parental Lock is setting as Off, the change of the MPAA Rating, Parental Guide ,CA Eng Rating and CA Fren Rating will be no useful.
Movie Rating (MPAA): Blocks movies according to the movie ratings limits specified, so children cannot view certain movies. You can set the ratings limit by blocking out all the movies with the ratings above a specified level. Keep in mind that the movie ratings limit only applies to movies shown on TV, not TV programs, such as soap operas.
1 Press elect MPAA Rating item.
2 Press the button and then use / button to select the rating.
3 Press the ok button to set block or unblock.
4 When you are satisfied with your choice, press MENU button to return to
the previous menu or press the EXIT button to return to TV viewing.
Video
Audio
Time
A
B
C
Channel
Function
Lock
Password
Parental Lock On
MPAA Rating
Parental Guide
CA Eng Rating
CA Fren Rating
NR
G
PG
PG-13
R
NC17
X
: Move cursor, /OK: Go to submenu, / ME NU: Return to upper menu,
EXIT: Exit main menu
32 TV LCD-TFT
Operation
Lock setup
Parental Guide
Parental Guide
: Blocks any channels that you do not want to watch or that you do not want your children to watch.
Note : The Parental control will automatically block certain categories that are more restrictive . For example, if you block TV-Y category, then
TV-Y7 will automatically be blocked. Similarly, if you block the TV-G category, then all the categories in the young adult group will be blocked (TV-Y, TV-Y7, TV-G, TV-PG, TV-14, and TV-MA). The sub-ratings
(D, L, S, V) work together similarly.
How to set the FV, D, L, S and V sub-ratings.
First, the / button select one of these Ratings:
TV-Y, TV-Y7, TV-G, TV-PG,TV-14, or TV-MA , and press the / button.
A symbol will be displayed for each sub-rating.
While is selected, press the OK button to go to a sub rating.
To select a different Rating, press the / buttons and then repeat the process.
Note: The V-chip will automatically block certain categories that are More restrictive .For example, if you block sub-rating in
TV-PG, then the sub-ratings in TV-14 and TV-MA will automatically be blocked.
Video
Audio
Time
A
B
C
Channel
Function
Lock
Password
Parental Lock On
MPAA Rating
Parental Guide
CA Eng Rating
CA Fren Rating
ALL FV D S L V
TV-Y V
TV-Y7 V V
TV-G V
TV-PG
TV-14
TV-MA
: Move cursor, /OK: Go to submenu, / ME NU: Return to upper menu,
EXIT: Exit main menu
CA Eng Rating
Canadian English Language Rating
1
Press elect CA Eng Rating item.
2 Press the button and then use / button to select the rating.
3 Press the ok button to confirm.
4
When you are satisfied with your choice, press MENU button to return to
the previous menu or press the EXIT button to return to TV viewing.
C Children
C8+ Children eight years and older
G General Programming, suitable for all audiences
PG Parental Guidance
14+ Viewers 14 years and older
18+ Adult Programming
Video
Audio
A
B
C
Time
Channel
Function
Lock
Password
Parental Lock On
MPAA Rating
Parental Guide
CA Eng Rating
CA Fren Rating
C
C8+
G
PG
14+
18+
Block All
: Move cursor, /OK: Go to submenu, / ME NU: Return to upper menu,
EXIT: Exit main menu
CA Fren Rating
Canadian French Language Rating
1 Press elect CA Fren Rating item.
2 Press the button and then use / button to select the rating.
3 Press the ok button to confirm.
4 When you are satisfied with your choice, press MENU button to return to
the previous menu or press the EXIT button to return to TV viewing.
G General
8 ans+ 8+ General - Not recommended for young children
13 ans+ Programming may not be suitable for children under the
age of 13
16 ans+ Programming is not suitable for children under the age of 16
18 ans+ Programming restricted to adults
Video
Audio
Time
A
B
C
Channel
Function
Lock
Password
Parental Lock On
MPAA Rating
Parental Guide
CA Eng Rating
CA Fren Rating
G
8 ans+
13 ans +
16 ans +
18 ans +
Block All
: Move cursor, /OK: Go to submenu, / ME NU: Return to upper menu,
EXIT: Exit main menu
Owner s Manual 33
Brief Info.
- Brief Info shows the present screen information.
- Press the INFO button to show the Brief Info on the screen.
- Press the INFO button or EXIT button to exit.
Function:
Show the present screen information.
Press the INFO button or EXIT button to exit.
A: Program title
B: categories
C: Video resolution
D: Program name
E: Additional information.
F: Program signal intensity
G: Present time, Day of week, Month
Operation
Quick program view
This function enables quick swap to the last watched program.
1
Suppose the channel number you used just now is 8 and the channel number you are using is 18 (as shown in the figure).
2
If you want to return to the last watched program channel 8, you can simply press the
Q.View button.
3
If you want to return to channel 18, press the button again. Use this function, you can easily change between the channel you are using and the channel you used last time.
34 TV LCD-TFT
USB System
USB and Card Reader play prepare
1. Supporting equipment
1.Equipment supporting Mass and Storage agreements include USB, mobile hard disk, card reader, some MP3 and digital camera.
2.Equipment supporting PTP agreement includes some digital camera.
2. 1 Supporting media:
picture, music, MPEG4, MPEG2 and MPEG1;
Supporting file format
*.Avi, *.DIVX, *.MPEG,*.DAT, *.MP3, *.WMA,
*.JPG and *.JPEG. Due to particularity of file code and file mode, It is possible that some files cannot be read.
2 If Pic & Music mode is activated, relative media file format will include JPEG and MP3 files. After
Picture is selected, MP3 files set for play will open both music and picture files for sync play performance. As some files must be read while music is being played, the speed of picture operation response might be affected.
3.Before starting operation, verify USB storage device is of FAT32 and FAT file system format. At present, this television does not support NTFS and the file systems of other format.
4.Many movie files use suffix of AVI and MPG.
However, many kinds of format are used for internal files. This television can only play some AVI and MPG files of this format. Those files with suffix of dat are not movie files, but data files used by computers, and cannot be played for movies.
5.External card reader supports most digital cards available in the market. Readable digital cards are classified according to the property of card readers and can be connected to mobile hard disks (working voltage 5.0V, working current not over 500mA).
6. Some Time the television operation may be halted due to excessive rate of information code errors. In such case, restart the system. As there are many nonstandard USB mobile devices in the market. If this kind of USB mobile devices are used in the stream media play system, the problem of identification failure might occur. The same problem may also happen with computers, not televisions.
7.It is suggested that the external devices with
USB2.0 interface be used to improve velocity of information reading and continuity of information play.
USB System
USB and Card Reader setup
Note: Memory cards or USB devices are not supplied with this TV.
USB setup
1 Insert USB in the card slots at the right side of TV.
2 Insert it to be clicked in.
3 Press USB button on the remote controller to enter the stream media system.
CARD setup
This TV is Compatible with the card of SD/MMC/CF/MS format.
How to use
1
Jack of card
Instructions
Jack of SM card
Jacks of SD MMC MS card
Jack 1
Jack 2
Jack of CF card
Note
1.Please note chooses uses the digital memory card with you corresponds the receptacle
2.Card reader in 1 cannot simultaneously insert two kind of cards in the graphical representation position
2
Insert the card as right direction. As following Card in common use
1 CF card jack
2 MMC card jack
3 MS card jack
4 SDcard jack
C OMPACT F LASH
DIGITAL MEMORY CARD
128
M
ULTI
M
EDIA
CARD
128 SD
128MB
Note:
1.the card insertion time, after the flows media system starts 2s , insert the card to numerical code card reader , do not bring card to start flow media system.
2. After card insertion, indicator light will shines, and enters glitters condition, after period of time , indicator light enters constant bright condition, indicates already distinguishes finished, this time carries on play operation and so on .
3, In the market ,the digital card type are very many, please uses standard product of the standard factory , meets reads takes difficult or reads speed limits, please replaces the digital card.
USB System
Card data protection
- Do not remove the card/USB device when the content is being read or when
browsing. Such action may damage the memory card/USB device.
- Do not touch the terminals on the back of the card.
- Always insert a card in the correct direction. Failure to do so may result in
damage to the card and the unit.
- Do not subject the card to excessive pressure or strong impacts.
- Malfunctions of the unit or card may result in data loss or damage to the card.
- Haier shall not accept any liability for damage or loss of stored data.
Warning:
Memory cards can be swallowed by young children. Do not allow children to handle memory cards.
Please remove the memory card immediately after use.
USB System
O D M O D E
F AV II T A U D II O
HOTKEY
RETURN
TIM
E
TIM
E
To start the media play
1 Press the USB button on
the remote to enter
USB system.
2 The system start up about
2 seconds, and then i nsert
USB in the card slots
3 Press / to select the
desired item, and press
OK button to ensure it.
DEVICE
COPY
Multimedia Player
SETUP
Press the Up or Down key to select the desired option.
Press OK to enter.
4 If to cancel the USB system , press
EXIT button to return to the main menu, and
then press TV button to select TV source .
Note: If there are no operation two minute later, the
TV will enter the saver automatically, at the time, press any button of USB system(with the exception of USB button) to exit the saver menu.
To operate the menu
1. Press / to select the item with up or down.
2 Press / left or right.
to select the desired item of submenu with
3 Press OK button to ensure the desired option to enter the submenu to resume the speed of standard.
4. Press or button to operate play quickly or slowly.
5.Press button to make the program stop and press again to resume it.
6.Press ZOOM button to make zoom, and press button to enjoy the detail.
/
7 Press HOTKEY button to call up or exit the OSD information.
And press HOTKEY button to call up or exit the OSD during operating file copy.
8 Press RETURN button to return to previous menu and stop play, press RETURN button repeatedly to return to main menu.
USB System
M O D
FA V..L
D E
HOTKEY
RETURN
TIME
TIME
Note:
1.the play file menu are different with your USB devices.
2. May carry on the programming playing: repeated step 2 to choose many documents, ( right key choice or cancellation picture choice), press OK to play, at this time, the picture of play will be the picture be choosed.
To select broadcast system
1
.
Press / button to select
DEVICE item.
(The device be inserted and
identified).
2
.
Press OK button to enter
adjusted option.
DEVICE
COPY
Multimedia Player
SETUP
Press the Up or Down key to select the desired option.
Press OK to enter.
To play picture
Multimedia Player
DEVICE
1
Press
/
button to
select Picture item.
COPY
2
Press OK button to
enter the menu of play.
SETUP
Picture
Press the Right or Left key to select the desired option.
Press to enter. PressRETU RNbac k.
3
Press / button to select
desired enjoy picture, and
then press OK button to
enter the play interface.
Note you may play the pictures among selected.
DEVICE
COPY
Multimedia Player
C No Name
D No Name
SETUP
Press the Up or Down key to select the desired volume.
Press OK to enter.
4
During playing picture, Press
HOTKEYbutton to call up picture
menu, at this time, you can
operate the picture of playing.
5
Press
to select the adjusted item,
Press OK button to
confirm.
DEVICE
COPY
Multimedia Player
F-007 .JPG
F-008 .JPG
F-009 .JPG
F-010 .JPG
F-011 .JPG
F-012 .JPG
SETUP
Press to the f ile . Press RETURN to return.
play or pause
stop;
overturn;press button to
right turns over 90
not available;
12 pictures scan;
not available; play previous picture; play next picture;
6
Press RETURN button to exit.
Resolution 1024 x 768
Note: The analysis rate basis picture itself clarity different and is different.
USBSystem
M O
V..L
II
M O
HOTKEY
RETURN
TIM
E
TIM
E
To play Movie
1
Press
/
button to select
Movie option.
DEVICE
Multimedia Player
2
Press OK to enter playing
menu.
COPY
Movie
SETUP
3
Press button
select desired movie, and
press again OK to enter
the playing movie interface.
DEVICE
Press the Right or Left key to select the desired option.
Press to enter. PressRETU RNbac k.
Multimedia Player
C No Name
D No Name
COPY
4
During playing movie, Press
HOTKEY button to call up picture
SETUP
menu, at this time, you can
Press the Up or Down key to select the desired volume.
Press OK to enter.
operate the movie of playing.
5
Press button
to select the adjusted item,
Press Okbutton to
confirm.
: play or pause
: stop;
: not available;
: zoom
: play previous movie;
: play next movie;
Captions According to movie document itself whether has the captions to decide
Audio channel Mono, Stereo,
Left, Right
Play Mode Standard, Repeat All,
Repeat File
DEVICE
COPY
Multimedia Player
F-007 .JPG
F-008 .JPG
F-009 .JPG
F-010 .JPG
F-011 .JPG
F-012 .JPG
SETUP
Press to the f ile . Press RETURN to return.
6
Press RETURN button to exit.
USBSystem
M O
F AV II
M O D E
A U D II O T
HOTKEY
RETURN
TIM
E
TIM
E
To enjoy music
1
Press
/
button to select
Music option.
2
Press OK button to enter
play menu.
3
Press / button to select
the desired music, and then
press OK button to the
playing music interface.
Note: the play file menu are
different with your USB
device.
4
When playing music, Press
/
button to
select the adjusted item,
Press OK button to
confirm.
: play or pause
: Not available
: Not available
: play previous music;
: play next music;
Play Mode Standard,Repeat File,
Repeat All
DEVICE
AAA Multimedia Player
COPY
SETUP
Music
Press the Right or Left key to select the desired option.
Press to enter. PressRETU RNbac k.
DEVICE
COPY
Multimedia Player
C No Name
D No Name
SETUP
Press the Up or Down key to select the desired volume.
Press OK to enter.
DEVICE
COPY
AAA Multimedia Player
F-007 .JPG
F-008 .JPG
F-009 .JPG
F-010 .JPG
F-011 .JPG
F-012 .JPG
SETUP
Press to the f ile . Press RETURN to return.
5
Press RETURN button to exit
the playing.
USBSystem
O D M O D E
F AV II T A U D II O
HOTKEY
RETURN
TIM
E
TIM
E
To select the Music and PIC combo
1
Press / button to select
Music and Pic option, and
press ENTER button to enter
play menu.
DEVICE
AAA Multimedia Player
COPY
2
Press
/ to select desired
file(picture and music), and
press ENTER button to enter
play menu.
SETUP
Comb
Press the Right or Left key to select the desired option.
Press ENTER to enter. PressRETUR Nback .
AAA Multimedia Player
3
During playing music, Press
HOTKEY button to call up picture
DEVICE
COPY
menu, at this time, you can
operate the movie of playing.
SETUP
C No Name
D No Name
Press the Up or Down key to select the desired volume.
Press ENTER to enter.
4
Press / button
to select the adjusted item,
Press OK button to
confirm.
DEVICE
COPY
Multimedia Player
F-007 .JPG
F-008 .JPG
F-009 .JPG
F-010 .JPG
F-011 .JPG
F-012 .JPG
play or pause stop;
: Not available
: Not available
: Not available
: Not available
: play previous music;
:play next music;
SETUP
Press OK to play the f ile . Press RETURN to return.
Resulotion 1024 x 768
5
Press repeatedly RETURN button
to return.
Note: Under music and picture condition, because the system reads the time of picture more longer than reads the time of music , therefore in the broadcast process, the picture appears the time lag to the music, this belongs to the normal phenomenon.
USB System
To select text
M O
F AV II
M O
A U D II O T
HOTKEY
1
Press
/
button to select
text option, and press OK
button to enter text menu.
TIM
E
TIM
E
RETURN
2
Press
/
to select desired
text, and press OK button
to confirm.
3
P ress button
to watch the text.
4
Press repeatedly
RETURN
button to return.
Multimedia Player
DEVICE
COPY
SETUP Text
Press the Right or Left key to select the desired option.
Press to enter. PressRET URNback .
DEVICE
AAA Multimedia Player
C No Name
D No Name
COPY
SETUP
Press the Up or Down key to select the desired volume.
Press OK to enter.
DEVICE
COPY
Multimedia Player
F-007 .txt
F-008 .txt
F-009 .txt
F-010 .txt
F-011 .txt
F-012 .txt
SETUP
Press OK to play the f ile . Press RETURN to return.
USBSystem
M O D E
F AV II T
M O
TIM
E
TIM
E
HOTKEY
RETURN
Copy file function
1
Press / to select Copy item.
Multimedia Player
2
Press OK button to enter
the copy menu.
DEVICE
COPY
3
Press
/
button to select the
desired item of copy.
SETUP
Press the Up or Down key to select the desired option.
Press OK to enter.
4
Press HOTKEY button to call up
Copy, Paste and delete, and
then press
/ button to select
Copy, and press OKbutton
to confirm.
DEVICE
COPY
Multimedia Player
C No Name
D No Name
5
To select a folder, then Press
OK button to enter, and then
press HOTKEY button to call up
Paste item, Press OK button
to confirm.
SETUP
Press the Up or Down key to select the desired volume.
Press OKI to enter.
6
If there are the same texts
between the texts of paste, the
File already exist! Do you want
Overwrite it? will display on
the screen, at this time, press
desired item, Press OK
button to confirm.
DEVICE
COPY
Multimedia Player
F-007 .JPG
F-008 .JPG
F-009 .JPG
F-010 .JPG
F-011 .JPG
F-012 .JPG
SETUP
Press OK to play the f ile . Press RETURN to return.
7
.
Press OK to cancel.
DEVICE
COPY
Multimedia Player
F-007 .JPG
F-008 .JPG
F-009 .JPG
F-010 .JPG
F-011 .JPG
F-012 .JPG
Copy
Paste
Delete
SETUP
Press OK to play the f ile . Press RETURN to return.
USBSystem
M O
V..L
II
M O
TIM
E
TIM
E
HOTKEY
RETURN
To select language
1
Press
/
to select
SETUP item.
Multimedia Player
DEVICE
COPY
2
Press OK button to
enter SETUP menu.
SETUP
Press the Up or Down key to select the desired option.
Press OK to enter.
3
Press
/
to select
language option, and then
press OK button to
enter the submenu.
DEVICE
AAA Multimedia Player
COPY
Language
Slideshow Model
4
Press to select
desired language, and
press OK to ensure
it.
SETUP
Press the Up or Down key to select the desired option.
Press OK to enter.
5 Press RETURN button to
return.
AAA Multimedia Player
DEVICE
COPY
English
French
Spanish
SETUP
Press the Up or Down key to select the desired option.
PressOK to enter.
Slideshow Model
1
After entering the SETUP menu.
2
Press
/
to select
Slideshow Model option,
and then press OK
button to enter the submenu.
DEVICE
COPY
AAA Multimedia Player
Language
Slideshow Model
SETUP
Use the Up and Down key to select the desired option.
Press OK to enter.
3
Press
/
to select
desired mode, and press
OK to ensure it.
DEVICE
AAA Multimedia Player
4
Press RETURN button to
return.
COPY
Fine Model
Normal Model
SETUP
Fine Model
Picture clarity high, the browsing speed is slow¡£
Normal Model
Use the Up and Down key to select the desired option.
Press OK to enter.
Picture clarity normal, the browsing speed is quick
Maintenance
- Early malfunctions can be prevented. Careful and regular cleaning can
extend the amount of time you will have your new TV. Be sure to turn the power
off and unplug the power cord before you begin any cleaning.
Cleaning the Screen
1 . Here`s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it`s almost dry, and then use it to wipe the screen.
2 . Make sure the excess water is off the screen, and then let it air-dry before you turn on your TV.
Cleaning the Cabinet
To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth. Please be sure not to use a wet cloth.
Extended Absence
If you expect to leave your TV dormant for a long time (such as a vacation), it`s a good idea to unplug the power cord to protect against possible damage from lightning or power surges.
Specifications
External Antenna Impedance
1920*1080(Dot)
120V~ , 60Hz
NTSC ATSC Clear QAM
75 ohm
HL52E
HL47E
HL42E
HL37E
(Including stand)
57.5*13.6*40.7inches
1460*345*1034mm
51.6*13*38.2 inches
1310*330*970mm
48.1*12.5*34.7 inches
1207*317*881mm
40.1*14*32.1 inches
1018*355*815 mm
125.5/56.9
86.5/39.2
80.5/43.4
77.25/35
The specifications shown above may be changed without prior notice for quality improvement.
42 TV LCD-TFT
Troubleshooting
Troubleshooting
For the sake of time and cost, it is strongly recommended that you check out the problem by yourself according to the instructions listed hereunder before contacting the after-sales service for technical assistance.
No picture, no sound
Blank screen
No sound
Poor sound
No picture in some channel
No color for some channel program
(black and white)
Spots with some or all pictures
Horizontal/vertical bars or picture shaking
Television out of control
Verify if the television is properly plugged.
Verify if the television is properly supplied power.
Verify if electricity is available.
Verify if correct signals are input.
Press INPUT button to change signal input to TV input.
Restart the television of power supply is interrupted.
Press Mute button and verify if Mute mode is set.
Switch to other channel and verify if the same problem happens.
Press VOL+ button to see if the problem can be solved.
Verify if sound system is correct. Refer to some chapter for adjust.
Verify if correct channel is selected.
Adjust the antenna.
Make adjustments by Fine Tune and Manual Scan.
Verify if the same problem exists in other channels.
Check out of picture and sound systems.
Refer to relative instructions in the Manual for color adjust.
Verify if the antenna is correctly connected.
Verify if the antenna is in good condition.
Make fine adjustment of channel.
Check for local interference such as an electrical appliance or power tool.
Disconnect the television from power supply and, 10 seconds later, connect the television to the power supply.
If the problem still exists, contact authorized after-sales service for technical assistance.
Note: Do not leave the television with static picture in an extended period as it may result in residual image on your television screen.
Note : Production of the plasma screen requires high and precision technologies. However, there might be some dark or bright (red, blue or green) spots, or some anomalistic stripes or spots. This is not defect. If the TV set is used in an area 2,400 meters above the sea level where the air pressure is below 750hpa, the picture on the plasma screen may be affected and a muffled sound might be produced. These phenomena might happen in the area 1,500 meters above the sea level. This is resulted from difference between air pressures inside and outside the display. This is not a defect covered by the limited warranty.
44 TV LCD-TFT
This Haier brand product, when shipped in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective product with a new or re-manufactured equivalent at no change to the purchaser, for parts or labor for the periods set forth below:
This warranty does not apply to the appearance of the product or the exterior of the product, which has been damaged or defaced, altered or modified in design or construction. It does not apply to the additional excluded items set forth below:
The warranty commences on the date the item was purchased and the original purchase receipt must be presented to the authorized service center before warranty repairs are rendered.
Responsibility of Haier to the purchaser with respect to the product, and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict duality or otherwise. In no event shall Haier be liable, or in any way responsible for any damages or defects in the product which were caused by repairs or attempted repairs performed by anyone other than an authorized service center or dealer; nor shall
Haier be liable, or in any way responsible for incidental or consequential economic or property damage. Some states do not allow the exclusion of incidental or consequential damages, so that above exclusion may not apply to you.
THIS WARRANTY GIVES YOU
SPECIFIC LEGAL RIGHTS. YOU MAY
ALSO HAVE OTHER RIGHTS WHICH
VARY FROM STATE TO STATE.
The limited warranty described herein is in addition to whatever implied warranties may be granted to purchasers by law. ALL
IMPLIED WARRANTIES INCLUDING THE
WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR USE ARE LIMITED TO THE
PERIOD(s) FROM THE DATE OF PURCHASE
SET FORTH BELOW. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
Warranty period for this product: one year parts and labor .
Additional items excluded from warranty coverage: non-rechargeable batteries.
Where to obtain service: For the location of the nearest Haier authorized service center or to obtain product literature, accessories, supplies or customer assistance, please call 1-877-337-3639.
What to do to obtain service: ship or carry in your product to an authorized service dealer or center .Be sure to have proof of purchase.
If you ship the product, be sure it is packaged carefully.
Haier America
New York, NY 10018
Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those described herein, or to extend the duration of any warranties beyond the time period described herein on behalf of Haier.
The warranties described herein shall be the sole and exclusive warranties granted by
Haier and shall be the sole and exclusive remedy available to the purchaser. Correction of defects in the manner and for the period of time described herein, shall constitute complete fulfillment of all abilities and
Owner s Manual 47
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Key Features
- 106.7 cm (42") LCD
- Full HD 1920 x 1080 pixels 15:9
- 550 cd/m² 8 ms 800:1
Related manuals
advertisement