DXEngineering.com I 800.777.0703

DXEngineering.com I 800.777.0703
World Class Products Shipped Worldwide, Every Day!
We’ll Beat Competitors’ Prices—Call Us!
DXEngineering.com I 800.777.0703
IC-9100 HF/VHF/UHF Transceiver
IC-7410 HF/50MHz
Base Station Transceiver
This dedicated HF/50 MHz transceiver has a DSP unit
and double conversion super-heterodyne system developed from the IC-7800/7700/7600 series
transceivers. It features a built-in 15 kHz first IF filter and can accept up to two optional filters
(3kHz/6kHz, not included) to protect narrow mode signals (such as CW and SSB) from adjacent
strong signals. Power Requirement: 13.8 Vdc @ 23A. Dimensions: 12.4" W x 4.57" H x 11" D.
• 32-bit floating point DSP unit provides high dynamic range and superior S/N ratio
• Double conversion super-heterodyne system reduces signal distortion,
improves in-band IMD characteristics
• +30 dBm third-order intercept point (in 14 MHz band)
• Operates in all modes (SSB/CW/RTTY/AM/FM)
• ±0.5 ppm frequency stability
• Optional RS-BA1 unit for IP remote control
• Built-in automatic antenna tuner
ICO-IC-7410
HF/50MHz Base Station Transceiver..........................CALL/WEB
IC-718 HF Base
Station Transceiver
The most practical DSP rig you’ll ever own! Covers 160
to 10 meters (except 60 meter) in CW, RTTY and AM
modes. Power Requirement: 13.8 Vdc @ 20A.
Dimensions: 9.4" W x 3.75" H x 9.4" D. Weight: 8.5 lbs.
• 5-100 watts adjustable output power
• 2-40 watts AM
• 101 scannable memory channels
• 0.03-30 MHz RX coverage
• IF shift control
• Mic compressor
• RF gain control, RF attenuator/preamp
• Auto-notch filter
• Electronic CW keyer, VOX voice operation • Digital S/RF meter
• High frequency stability
• Optional filter selection
• Front facing speaker
• Hand mic included
ICO-IC-718
HF Transceiver/SW Receiver......................................CALL/WEB
IC-7200 HF/50MHz Portable
Base Station Transceiver
This entry-level transceiver has advanced digital features, like IF DSP technology that
higher class transceivers have. It is built tough and water-resistant for outdoor use. Power
Requirement: 13.8 Vdc @ 22A. Dimensions: 9.5" W x 3.3" H x 11" D. Weight: 12.1 lbs.
• Covers 160-6 meter transmit bands and 0.03-60 MHz receive bands
• 2-100 watt output on SSB, CW, RTTY (1-40 watt on AM)
• IF DSP filtering (51 passband widths)
• Hand mic, DC power cable, and spare fuses
• Water intrusion protection similar to Icom Marine radios
• Digital IF filter, twin passband tuning (PBT) and noise reduction
• LCD backlight (hi/lo/off), front facing speaker, voice synthesizer
• Rear bumper protects rear panel connectors while transporting
• 201 scannable memory channels
• Manual notch filter
• Dual VFOs
• ±0.5 ppm frequency stability
• CI-V interface
• USB port for PC control
ICO-IC-7200
Portable HF/6M Transceiver.......................................CALL/WEB
IC-7600 High Performance
HF/50 MHz All Mode Transceiver
This unit has the latest DSP technologies used in the
IC-7800/7700 transceivers, plus Icom’s 45 years of
analog circuit expertise to give you a pronounced performance advantage. Power
Requirement: 13.8 Vdc @ 23A. Dimensions: 13.4" W x 4.5" H x 11" D. Weight: 25 lbs.
• Covers 160-6 meter transmit bands and 30 KHz-60 MHz receive
• 2-100 watt output for SSB, CW, FM, RTTY, PSK31
• 1-30 watt output for AM
• 101 scannable memory channels
• Separate DSP units for transmitter/receiver and spectrum scope
• Three built-in 1st IF (roofing) filters: 3, 6 and 15 KHz
• Double conversion receiver with image rejection mixer to improve in-band IMD
• Two SO-239 antenna connectors with automatic antenna selector
• Widescreen 5.8" (400 x 240 pixel) display
• High-resolution real-time scope using a dedicated DSP unit
• USB connectors for keyboards, flash memory drives, and PCs
• Built-in PSK and RTTY operation with a USB keyboard—PC not required
• DC power cable, spare fuses, CW key plug, HM-36 hand mic, carrying handle
ICO-IC-7600
High Performance Transceiver ..................................CALL/WEB
IC-7700 HF/50MHz All Mode Transceiver
The top performance, Contest and DX chasing transceiver! It features the latest
technology including two independent IC-7800-type DSP units (one for the
transmitter/receiver, one for the spectrum display). Dimensions: 16.7" W x 5.9" H x
17.1" D. Weight: 52.9 lbs.
• 40 dBm third order intercept point
• Typical 134 dB@5 kHz dynamic range
• Selectable 3, 6 and 15 kHz roofing filters
• Exceptional out-of-band signal rejection
• Built-in switching power supply
• 7" color TFT (800 x 480 pixel) LCD
• Automatic tracking preselector and relay-switched front end
• Push-pull 48 Vdc MOSFET amplifiers—200 watts at full duty cycle
• Accepts external VGA monitor
• Built-in RTTY/PSK31 mode—requires only an external keyboard
• Rear-panel I/O allows interface of a second Icom transceiver
• Digital voice recorder, DSP noise blanker, USB flash drive socket
ICO-IC-7700
All Mode Transceiver .................................................CALL/WEB
IC-7800 Deluxe HF/50 MHz Transceiver
The ultimate fusion of 45 years of analog RF circuit development and cutting-edge digital
technology. You get dual receivers with an astonishing 110 dB dynamic range, +40 dB 3rd
order intercept point in HF, and many other features. No other transceiver comes close!
Dimensions: 16.6" W x 5.9" H x 17.1" D. Weight: 55 lbs.
• Covers 160-6 meter transmit bands and 30 KHz-60 MHz receive
• 5-200 watt output (5-50 watt AM)
• USB, LSB, CW, RTTY, PSK-31, AM, FM,
SSB DATA modes
• Four 32-bit floating point DSP units and 24-bit
AD/DA converters
• Built-in power supply (85-265 Vac)
• Ultra high stability oscillator
• Main and sub receivers, separate 50 MHz preamp and mixer
• Digital twin passband tuning
• 7" color TFT LCD with spectrum scope S-meter and RTTY/PSK31 decode messages
• Digital RF speech compressor, voice synthesizer, mic equalizer
• RTTY/PSK-31 without PC connection
• UTC/local clock and timer function
• External CRT display connector, four antenna connectors
• Includes 64MB CF memory card and rack mount handles
ICO-IC-7800
Deluxe HF/6M Transceiver .........................................CALL/WEB
Remotely Control Icom Transceivers Through an IP Network!
Icom IP Remote Control Software
The IP Remote Control Software allows you to operate an Icom
radio installed in another room using your home network or even
from a remote location over the Internet. The software works with
Icom IC-9100, IC-7800, IC-7700, IC-7600, IC-756PROIII, IC-746PRO,
IC-7400 IC-7200, and IC-7000 transceivers. Operating system
requirements: Windows® XP (SP3), Vista, or Windows® 7.
ICO-RS-BA1 Icom IP Remote Control Software ........$99.00
Mail: P.O. Box 1491, Akron, OH 44309 • E-Mail: DXEngineering@DXEngineering.com • Web: DXEngineering.com
3
Station Equipment
This compact, all-in-one transceiver provides sophisticated HF/VHF/UHF operation with
room to grow. The IC-9100 covers most ham bands and modes, and offers a wide variety
of operating styles. Add the optional UX-9100 1,200 MHz band unit and UT-121 D-Star
unit for increased communications capabilities. Power Requirement: 13.8 Vdc @ 24A.
Dimensions: 12.4" W x 4.57" H x 13.5" D.
• Covers HF/50, 144, 430/440 amateur bands in SSB, CW, AM, and FM modes
• Built-in voice synthesizer announces operating frequency, mode, and S-meter level
• Voice Squelch Control (VSC) function
• AFC function (FM/DV mode)
• Five scanning modes: program, memory, select memory, mode select, Δf scan
• RF speech compressor
• Microphone equalizer and adjustable transmit bandwidth
• Two preamplifier types for HF/50 MHz bands (low-level and high-gain)
• CTCSS and DTCS tone encoder and decoder
• Audio equalizer function
• SSB/CW synchronous tuning
• 9600bps data socket
• Automatic* and one-touch repeater functions
• Optional UX-9100 unit for operating on the 1200MHz band
• Optional UT-121 D-Star unit for digital voice and low speed data communication
ICO-IC-9100
HF/VHF/UHF Transceiver............................................CALL/WEB
*USA and KOR versions only.
Station Equipment
Mobile
Transceivers
IC-7000
All-Band Multi-Mode Mobile Transceiver
This mobile transceiver has features normally found only in the top base stations, like
41 filter bandwidths with sharp or soft filter shape. The variable twin PBT allows you to
narrow the IF passband or shift the entire passband to eliminate QRM. The 2.5 inch
(diagonal) color TFT screen supports a two-mode band scope. It includes a backlit
remote microphone, spare fuses, key plug, DC power cable, and remote mounting
package. Power Requirement: 13.8 Vdc @ 22A. Dimensions: 6.56" W x 2.59" H x 7.09" D.
Weight: 5.1 lbs.
• Covers HF/6M/2M/440 MHz bands with .03-199 MHz RX coverage
• Power: 100 watts (HF+6M), 50 watts (2M), 35 watts (440 MHz)
• 503 alpha tag memories
• Internal 4-memory CW keyer
• Detachable control head
• Digital RF speech processor
• S/PWR/SWR meter
• Preamp and attenuator
• RTTY demodulator
• Adjustable SSB TX bandwidth
• DTMF memory
• VOX plus full break-in CW with adjustable pitch
ICO-IC-7000
All-Band Transceiver .................................................CALL/WEB
IC-2820H
2M/400 Analog Dual Band Mobile Transceiver
Covers 144-148 MHz and 430-450 MHz transmit. Left band receive: 118-549.95 MHz
wideband. Right band receive: 118-173.995/375-549.995/810-990.990 MHz cellular
blocked. Inputs for two antennas allow diversity reception (compares signal strength
from the two antennas, automatically selects the strongest signal) in the
127/136/146/375/440/500 MHz bands. V/V and U/U simultaneous receive antennas
required. Includes a full-function backlit remote DTMF hand microphone, mounting
bracket, DC power cable, separation cables, and spare fuses. Power Requirement:
13.8 Vdc @ 13A. Dimensions: 5.9" W x 1.65" H x 7.4" D. Weight: 3.3 lbs.
• D-STAR/GPS and DV (digital voice) upgradeable with optional UT-123 Receiver
• Selectable Power: 50/15/5 watts on both bands
• 522 memory channels
• Weather Alert
• CTCSS/DCS encode/decode
• PC compatibility
• Removable front panel
• Selectable (amber/green) display
• Packet ready (9600 BPS/6-pin DIN)
ICO-IC-2820H
Analog Dual Band Transceiver...................................CALL/WEB
IC-2300H
2M Single Band Mobile
Transceiver
Covers 144-148 MHz transmit with 136-174
MHz receive. Large selectable (amber or
green) LCD display with four levels of brightness, backlit keys, and a large oversized
tuning dial. It includes a remote control microphone, DC power cable, and mobile
mounting bracket. Power Requirement: 13.8 Vdc @15A. Dimensions: 5.5" W x 1.6" H x
5.25" D. Weight: 2.75 lbs.
• Selectable transmit power levels: 65 /25/10/5 watts
• Choice of FM Narrow mode
• 207 alpha tag memories w/call channel
• Dynamic Memory Scan
• 50 CTCSS and 104 x 2 DTCS encode/decode,
tone scan function, pocket beep
• 24 DTMF autodial memories
• Squelch delay
ICO-IC-2300H
2M Single Band Transceiver ......................................CALL/WEB
4
IC-V8000 2M Single Band High Power Mobile Transceiver
Covers 144-148 MHz transmit with 118-174 MHz receive. User selectable power (75/25/10/5
watts, 75 watts maximum). It includes a remote control microphone, DC power cable, and
mounting bracket. Power Requirement: 13.8 Vdc @ 15A. Dimensions: 5.9" W x 2" H x 5.9" D.
Weight: 2.22 lbs.
• 207 alpha tag memories with Call Channel and priority watch
• Transceiver to transceiver or PC to transceiver cloning
• Weather channel scan and alert
• DMS scan system
• CTCSS/DTCS tones
• Customized memory banks
• DTMF encode and pager
• 10 DTMF memory channels
• Front facing speaker
• One-piece, die-cast aluminum chassis
• Selectable display (amber or green)
ICO-IC-V8000
2M High Power Transceiver ......................................CALL/WEB
ICOM Accessories
ICO-AH-4
Wire-Fed Antenna Auto-Tuner 80-6 meter..........................CALL/WEB
ICO-AT-180
Coax-Fed Antenna Auto-Tuner HF plus 6 meter..................CALL/WEB
ICO-CR-282
High Stability Crystal Unit for IC-706 MKIIG ......................CALL/WEB
ICO-CR-338
High Stability Crystal Unit for IC-718 Tranceiver ................CALL/WEB
ICO-CT-17
Level Converter for PC Interface .........................................CALL/WEB
ICO-FL-52A
500 Hz/455 kHz IF CW Filter ...............................................CALL/WEB
ICO-FL-100
500 Hz/9 MHz IF CW Filter..................................................CALL/WEB
ICO-FL-101
250 Hz/9 MHz IF CW Filter..................................................CALL/WEB
ICO-FL-103
2.8 kHz/9 MHz IF SSB Filter................................................CALL/WEB
ICO-FL-222
1.9 kHz/455 kHz IF SSB Filter .............................................CALL/WEB
ICO-FL-232
350 Hz/9 MHz IF CW/RTTY Filter........................................CALL/WEB
ICO-HM-154T
TTP Mic for IC-703/706/7000 .............................................CALL/WEB
ICO-MB-23
Carrying Handle for IC-718 and R75 ..................................CALL/WEB
ICO-MB-62
Mounting Bracket 706/7000 Main Unit...............................CALL/WEB
ICO-MB-72
Carrying Handle for IC-706 Series Tranceiver.....................CALL/WEB
ICO-MB-105
Remote Head Bracket for IC-7000 ......................................CALL/WEB
ICO-OPC-025D
DC Power Cable for 706/718/746/756................................CALL/WEB
ICO-OPC-478
PC Control RS232C Cable...................................................CALL/WEB
ICO-OPC-478U
PC Control USB Cable 478UC.............................................CALL/WEB
ICO-OPC-581
11.5 ft. Separation Cable for 706 Series.............................CALL/WEB
ICO-OPC-587
16 ft. Separation Cable for 706 Series................................CALL/WEB
ICO-OPC-589
8-Pin Mic Jack Adapter Cable .............................................CALL/WEB
ICO-OPC-599
7+8-Pin to 13-Pin Adapter ..................................................CALL/WEB
ICO-OPC-1443
11.5 ft. Remote Cable for IC-7000......................................CALL/WEB
ICO-OPC-1444
16 ft. Remote Cable for IC-7000.........................................CALL/WEB
ICO-OPC-1457
DC Power Cable for IC-7000/7200/7600 ............................CALL/WEB
ICO-PS-125
25A Switching Power Supply..............................................CALL/WEB
ICO-PS-126
25A 4-Pin Switching Power Supply....................................CALL/WEB
ICO-PW1
Amplifier 160 to 15+6 Meter with Auto-Tuner ....................CALL/WEB
ICO-RMK-7000
Sep Kit Package MB-62/MB-105/OPC-1443.......................CALL/WEB
ICO-SM-50
Dynamic Desk Microphone .................................................CALL/WEB
ICO-SP-10
Slim-Line External Speaker .................................................CALL/WEB
ICO-SP-20
Speaker w/Audio Filters.......................................................CALL/WEB
ICO-SP-23
Speaker w/Audio Filters.......................................................CALL/WEB
ICO-UT-102
Voice Synthesizer ................................................................CALL/WEB
Visit DXEngineering.com for a complete list of Icom Accessories.
SP-20 External Speaker
ICOM
External Speakers
Improve the sound of your station with a speaker
that matches the style of your ICOM transceiver.
• Four selectable audio filters
• Headphone jack
• Speaker can connect up to two transceivers
• Input impedance: 8 Ω
• Maximum input power: 5W
ICO-SP-20 .............................................................$269.99
ICO-SP-23 .............................................................$239.99
SP-23 External Speaker
Phone: 800.777.0703 • International: 330.572.3200 • Fax: 330.572.3279 • DoD CAGE Code: 3M3H7
Heil Sound
Station Equipment
Microphones—Famous Heil microphones are for the enthusiast who appreciates
professional sound. The PRO series with broadband elements is ideal for the latest
audio equalizers and processors.
HLS-PR781
Dynamic Cardioid Studio Quality Mic, 3-Pin XLR ..............$179.00
HLS-GM-4
GOLDLINE 2-Element Mic, HC 4 Element ..........................$129.00
HLS-GM-V
Hi-Impedance GM for Vintage Rigs....................................$135.00
HLS-HM-4
Handi-Mic Hand Mic, HC 4 Element.....................................$79.00
HLS-HM-IC
Handi-Mic/Electret Element, Icom ........................................$85.00
HLS-HM-PRO
Handi-Mic with Broadcast Element ......................................$85.00
HLS-ICM
Mic for Icom, 8 ft. 8-Pin Cable Attached ..............................$99.00
HLS-PR20
PRO Broadcast Cardioid Mic, 3-Pin XLR ...........................$150.00
HLS-PR28
Compact Dynamic Cardioid Mic 3-Pin XLR .......................$135.00
HLS-PR40
PRO Wide Range Cardioid Mic, 3-Pin XLR........................$325.00
Headsets—Headsets combine comfort and great sound. The boomsets feature the famous
Heil microphone elements.
HLS-PROSET-4
PRO Boom Mic/Headset, HC 4 Element.............................$129.00
HLS-PROSET-6
PRO Boom Mic/Headset, HC 6 Element.............................$129.00
HLS-PROSETIC
PRO Boom Mic/Headset/Adapter, Icom Electret ................$139.00
HLS-HTSS
Single Side TRAVELER Headset ...........................................$75.00
HLS-HTDS
Dual Side TRAVELER Headset..............................................$89.00
HLS-PSE-6
PROSET Elite Boom Mic/Headset, HC 6 Element...............$159.00
HLS-PSE-IC
PROSET Elite Boom Mic/Headset, HC 6 Element,
Icom Electret.......................................................................$175.00
Cables and Adapters—Rugged HeilWire assemblies allow connection of Heil Sound
devices to transceivers. Visit DXEngineering.com and look up your specific mic or
headset and its “Suggested Parts” link to confirm compatibility.
Cables/Adapters for Icom
HLS-AD-1-I
PROSET 8-Pin Adapter Cable ...............................................$20.75
HLS-AD-1-IM
PROSET Modular Adapter Cable ..........................................$20.75
HLS-AD-1-IC
PROSET 8-Pin Adapter Cable ...............................................$20.75
HLS-AD-1-ICM
PROSET Modular Adapter Cable ..........................................$20.75
HLS-CC-1-I
XLR4 to 8-Pin Mic Cable .....................................................$35.75
HLS-CC-1-IM
XLR4 to Modular Mic Cable .................................................$35.75
HLS-CC-1-XLR-I
3 to 8-Pin Mic Cable .............................................................$35.75
HLS-CH-1-I8
XLR4 to 8-Pin Mic Coil Cable ...............................................$23.00
HLS-CH-1-IM
XLR4 to Modular Mic Coil Cable ..........................................$23.00
Cables/Adapters for Icom Cont.
HLS-HSTA-IC8 TRAVELER Adapter, Icom 8-Pin .................................................$23.00
HLS-HSTA-IM
TRAVELER Adapter, Icom Modular ............................................$23.00
Cables/Adapters for Kenwood
HLS-AD-1-K
PROSET 8-Pin Adapter Cable .....................................................$20.75
HLS-AD-1-KM PROSET Modular Adapter Cable ................................................$20.75
HLS-CC-1-K
XLR4 to 8-Pin Mic Cable ............................................................$35.75
HLS-CC-1-KM XLR4 to Modular Mic Cable .......................................................$35.75
HLS-CC-1-XLR-K XLR3 to 8-Pin Mic Cable ............................................................$35.75
HLS-CH1-K8
XLR4 to 8-Pin Mic Coil Cable .....................................................$23.00
HLS-CH-1-KM XLR4 to Modular Mic Coil Cable ................................................$23.00
HLS-HSTA-K8
TRAVELER Adapter, Kenwood 8-Pin ..........................................$23.00
HLS-HSTA-KM TRAVELER Adapter, Kenwood Modular......................................$23.00
Cables for Ten-Tec
HLS-CC-1-Y
XLR4 to 4-Pin Mic Cable ............................................................$35.75
HLS-CC-1-T
XLR4 to 4-Pin Mic Cable ............................................................$35.75
Cables/Adapters for Yaesu
HLS-AD-1-Y
PROSET 8-Pin Adapter Cable .....................................................$20.75
HLS-AD-1-YM PROSET Modular Adapter Cable ................................................$20.75
HLS-CC-1-Y
XLR4 to 8-Pin Mic Cable ............................................................$35.75
HLS-CC-1-YM XLR4 to RJ-45 Modular Mic Cable.............................................$35.75
HLS-CC-1-XLR-Y XLR3 to 8-Pin Mic Cable ............................................................$35.75
HLS-CH-1-Y8
XLR4 to 8-Pin Mic Coil Cable .....................................................$23.00
HLS-CH-1-YM XLR4 to Modular Mic Coil Cable ................................................$23.00
HLS-AD-100
Adapter, Yaesu 8-Pin Round to 6-Pin Modular ..........................$20.75
HLS-ADMY-817 Adapter, Yaesu 8-Pin Mic To FT-817 Modular ............................$25.00
HLS-HSTA-YM TRAVELER Adapter, Yaesu 8P Modular RJ45 ............................$23.00
Accessories
HLS-CB-1-PTT CLASSIC Base with PTT/Cough Switch......................................$70.00
HLS-SB-2
Small Adjustable Mic Boom .......................................................$55.00
HLS-PL2T
Topless PROLINE Boom...........................................................$109.00
HLS-SM-1
Shock Mount for 1" Stem Dia. Mic, GM/PR20 ...........................$69.00
HLS-SM-2B
Black Shock Mount for 2" Stem Dia. Mic, PR40 ........................$95.00
HLS-TM-1
Tri-Mount Mic Adapter................................................................$14.00
HLS-FS-2
Dual Switch Foot Switch.............................................................$40.00
HLS-HS-2
Ergonomic Pistol Grip Hand Switch ...........................................$29.00
HLS-BAG1
Leatherette Travel Bag for PROSET ............................................$25.00
HLS-BAG2
Leatherette Travel Bag for QPHONE/BM/TRAV...........................$20.00
MFJ-616
Speech Intelligibility Enhancer
MFJ-434B
Contest Voice Keyer™
“As I got older, my high frequency hearing loss was destroying…ham radio for
me...” Martin F. Jue, K5FLU/President and Founder of MFJ Enterprises, Inc.
Developed by Martin Jue to compensate
for his hearing loss, this enhancer
significantly increases speech energy
above 500 Hz where 83% of intelligibility
is concentrated, and reduces speech
energy below 500 Hz where only 4% of
intelligibility lies. Amateur radio communications limit audio to about 300 to 2,700 Hz. The
enhancer splits the audio band into four overlapping octave ranges centered at 300, 600,
1,200, and 2,400 Hz. You can boost or cut each range by nearly 20 dB to maximize speech
intelligibility for most kinds of frequency loss.
Output audio is split into left and right channels with separate 2.5 watt amplifiers; a
balance control lets you equalize the perceived loudness to each ear. The enhancer works
with SSB, FM, AM, CW or any voice mode on ham, marine, aircraft, and CB bands.
MFJ-616
Speech Intelligibility Enhancer................................................$189.95
Let this microprocessor-controlled
Contest Voice Keyer call CQ, send
your call, and do contest exchanges
for you in your own natural voice!
You can record and play back five
natural-sounding messages in a total of 75 seconds. EEPROM technology
stores messages for up to 100 years with no battery backup needed.
You can repeat messages continuously and vary the repeat delay from 3 to 500 seconds.
A receive audio jack lets you record and play back off-the-air signals—no more “please
repeat.” It makes a great voice beacon, too. This keyer requires a 9 volt battery, 9-15 Vdc
power source, or 110 Vac with optional MFJ-1312D Wall Adapter. It uses an 8-pin modular
or 8-pin round microphone plug.
MFJ-434B
Contest Voice Keyer................................................................$199.95
MFJ-1312D
Power Supply, 12 Vdc/500 Milliamp ........................................$15.50
MFJ-392B Communications Headphones
Plug in the ClearTone speaker and bring out
communication speech fidelity that you never knew
existed. It restores the smooth sound of sinewaves
that CW naturally generates and makes it easy to copy.
The ClearTone speaker improves speech intelligibility
in the 600 to 4,000Hz frequency range while reducing
undesirable noise, static, and hum. It has a 6 ft. cord and
3.5mm mono plug. Output: 8 watts. Impedance: 8 Ω.
Dimensions: 3 3/4" H x 3" W x 2 1/4" D.
MFJ-281
ClearTone Communications Speaker........................................$12.75
Microphones and Headsets
These headphones are perfect for amateur radio and shortwave
listening in all modes—SSB, FM, AM, data, and CW in mono
or stereo. Each earphone has an individual volume control.
The padded headband and ear-cushioned design make
listening extremely comfortable. The headphones handle
450 mW and have 100-24,000 Hz frequency response.
Impedance: 16 Ω at 1 KHz. Sensitivity: 102dB/mW.
MFJ-392B
Communications Headphones....$24.75
MFJ-281 ClearTone Communications Speaker
Mail: P.O. Box 1491, Akron, OH 44309 • E-Mail: DXEngineering@DXEngineering.com • Web: DXEngineering.com
5
LDG-Z-11PROII
LDG-AT-897PLUS
i-Mate Memory Control
The i-Mate allows external selection of
pre-recorded voice and keyed messages for
the Icom IC-7600/7700/7800, IC-756 PROII/III,
and IC-7000 transceivers, and keyed CW
messages for the IC-746 PRO transceiver. It
eliminates the need for shifting the display from
operating mode to memory select mode just to
transmit a pre-recorded message. Four buttons
allow direct access to your messages. The
i-Mate has a pulsed sinewave oscillator for
tuning amplifiers and antenna tuners. An
alternate audio input is provided for a second microphone
or boomset. It’s connected and powered by a single microphone jack.
• Works with CW and voice
• Send memories while keeping the spectrum scope on the display
• Easier access to memories with less hand movement
• Heil Pro-Set plugs directly into the i-Mate without an adaptor
• Separate PTT switch to key transceiver
• Auxiliary input can be used for digital modes
• MIC 1 switch allows switching between standard 8 pin microphone
connector and MIC 2 auxiliary input
• Pulsed sine wave oscillator for tuning—save finals in the amplifier
• Adjust pulsed oscillator with a small screwdriver
BTF-I-MATE
Icom Memory Control ..............................................................$79.99
ICO-OPC-589
Microphone adapter for IC-7000 transceiver ...........................$39.99
7000 Tune Control
This control lets you use the Tune/Call button on
your Icom IC-7000 transceiver for an external
manual tuner. The SWR is displayed on the radio
as you tune an antenna, amplifier, or external tuner.
A cable is included to connect to the CI-V jack and
motorized antenna control. Output: Constant 30
watts out or pulsed (50% duty cycle) at user
selectable power.
BTF-7000TUNE ................................$54.99
7000 Screwdriver Control
This control lets you use any screwdriver
antenna with an Icom IC-7000 transceiver.
All tuning is done with the existing IC-7000
controls—no extra buttons or speakers
required. No RF connections or radio/antenna
modifications needed. An Icom 7000 Tune
Control is required.
BTF-7000SCR ..................................$94.99
Yaesu Tune Control
This control lets you use the Tune button
function on your Yaesu FT-100, FT-857, or
FT-897 transceiver to provide a low power
output for tuning, adjusting an antenna,
checking SWR, etc. no matter what mode
you are using. It provides interface between
your Yaesu transceiver and Icom typeaccessories (such as antenna tuners),
tuners from other manufacturers, and
screwdriver antenna controllers. No radio
modification required. It can be used on Yaesu
FT-450 and FT-950 transceivers with easy modifications. Interface cable included.
BTF-YAETUNE..............................................................................................................$44.99
706 Tune Control
Use the Tune/Call button on your Icom IC-706
(all models) and IC-718 transceiver to tune your
antenna, an antenna tuner or to check SWR.
Push the button once and the transceiver emits
10 watts, steady carrier and sidetone through
an internal or external speaker.
BTF-706TUNE ..................................$32.99
6
LDG-AT-200PRO
LDG-YT-450
LDG-Z-817
LDG-FT-METER
LDG-AT-1000PRO
LDG-FTL-METER
LDG Electronics
Antenna Tuners and Accessories
Antenna Tuners
From stand-alone units to models that interface directly with
popular transceivers, LDG has a state-of-the-art, processorcontrolled automatic antenna tuner right for your rig.
LDG-AT-100PROII 1-125W Desktop Memory Tuner...$214.00
LDG-AT-200PROII 5-250W Desktop Memory Tuner...$234.00
LDG-AT-600PRO 5-600W Desktop Memory Tuner...$324.00
LDG-AT-1000PRO 1 kW Desktop Memory Tuner .......$544.00
LDG-IT-100
100W Icom Tuner
(AH-4/AH-3 compatible)................$179.00
LDG-KT-100
100W Kenwood Tuner
(AT-300 compatible)......................$199.00
LDG-YT-100
Desktop Tuner for FT-857,
FT-897, FT-100 ..............................$199.00
LDG-YT-450
Desktop Tuner for FT-450
and FT-950 ....................................$249.00
LDG-YT-847
Desktop Tuner for FT-847 .............$249.00
LDG-AT-897PLUS Bolt-on FT-897 Memory
Autotuner.......................................$194.00
LDG-Z-11PROII
0.1-125W Memory Autotuner .......$179.00
LDG-Z-100PLUS 0.1-125W Economy
Memory Tuner...............................$159.00
LDG-Z-817
QRP Autotuner with
FT-817 Interface ............................$129.00
LDG-ALK-2
LDG-M-7600
LDG-M-7700
LDG-RBA-1:1
LDG-RBA-4:1
LDG-SLS-2
Accessories
LDG-RBA-1-1
Remote 1:1 Balun .........................................................................$30.00
LDG-RBA-4-1
Remote 4:1 Balun .........................................................................$30.00
LDG-FT-METER 6-Function Meter for Yaesu FT-857/FT-897 .................................$49.00
LDG-FTL-METER 4.5" Meter for FT-857 and FT-897 ................................................$79.00
LDG-M-7600
4.5" Meter for IC-7600 ..................................................................$79.00
LDG-M-7700
4.5" Meter for IC-7700 ..................................................................$79.00
LDG-ALK-2
Audio/Linear/Key 2-Port Switch....................................................$49.00
LDG-SLS-2
RJ-45 Microphone Switch ............................................................$59.00
Visit DXEngineering.com to learn more about LDG antenna tuners and accessories!
Phone: 800.777.0703 • International: 330.572.3200 • Fax: 330.572.3279 • DoD CAGE Code: 3M3H7
No RF
Hash!
These MFJ and Ameritron switching power supplies are clean!
Your buddies won’t hear any RF hash on your signal…and you won’t hear
any from your receiver either. Some other competing power supplies may
generate RF hash in your transmitted and received signal. MightyLite
Switching Power Supplies meet all FCC Class B regulations.
AME-SPS-75MV
75 Amp Switching
Power Supply
The smallest and lightest power supply in
ham radio! This unit weighs only 2.9 pounds
and measures just 5 1/2" W x 2" H x 5 3/4" D.
It is ideal for the portable or temporary
operation of a full 100 watt HF transceiver.
The five-way binding posts are for high-current radio connects, while a pair of speaker
type push-on terminals is for low current accessories. It also features over-voltage and
over-current protection modes. A whisper-quiet internal cooling fan generates tremendous
airflow to help keep components cool.
• Switchable AC Input Voltage: 110 Vac at 47-62 Hz, 220 Vac at 47-63 Hz
• Super Regulation: Works with 85-135 Vac or 170-260 Vac input
MFJ-4125
Compact Switching Power Supply, 25 Amp, 13.8 Vdc ............$84.50
This power supply provides 75 amps continuous
output current—ideal for use the with
Ameritron’s ALS-500M 500 watt solid state
amplifier. It has less than 100 mV peak-to-peak
ripple under full load. Load regulation is better
than 1.5% under full load. Other features include
reverse-polarity protection, brownout input
protection, over-current/over-temperature protection, and a thermally-controlled quiet fan.
Output voltage is variable with metering for both voltage and current.
• Input: 108-132 Vac, 50/60 Hz
• Current Draw: 11 Amps
AME-SPS-75MV........................................................................................................$259.95
MFJ-4225MV
MightyLite 25 Amp Switching
Power Supply
MFJ-4035MV
30/35 Amp Regulated
Linear DC Power Supply
This unit features a front panel voltage control that
allows you to vary output voltage from 9 to
15 Vdc and gives you a highly regulated voltage
output, including 12 Vdc and 13.8 Vdc! The
front panel also has five-way binding posts for
heavy-duty use and a cigarette lighter socket for mobile accessories.
Large, brightly illuminated 3" dual meters make it easy to monitor load voltage and
current. A whisper-quiet internal fan efficiently cools your power supply.
MFJ-4225MV
MightyLite Switching Power Supply, 25 Amp, 13.8 Vdc ........$99.50
A massive 19.2 pound transformer makes
this heavy duty power supply ideal for
powering your entire station, including your
100 watt transceiver and all accessories. It
delivers 35 amps maximum/30 amps
continuous with load regulation better than
1%. Ripple voltage is less than 30 mV. No RF hash!
The unit has over-voltage, foldback short circuit, and over-temperature protection
systems. Cooling fan speed increases as load current increases to keep components cool.
It has a front panel voltage adjustment (1 to 14 Vdc) with a convenient detent set at 13.8
Vdc. The front panel meters let you monitor voltage and current. Three sets of output terminals include a pair of heavy-duty, five-way binding posts for HF/VHF rigs. Two pairs of
quick-connects for accessories, covered cigarette lighter socket and front panel fuse holder
included. Unit plugs into any 110 Vac wall outlet. Dimensions: 9 1/2" W x 6" H x 9 3/4" D.
MFJ-4035MV
Linear Power Supply, 35 Amp, 13.8 Vdc ...............................$139.95
MFJ-4245MV
MightyLite 45 Amp Switching
Power Supply
It fits in the palm of your hand—and is powerful
enough to run your HF or 2M/440 MHz radio and
accessories! This 45 amp MightyLite weighs just 5.5 lbs., seven times lighter than an
equivalent conventional power supply. That means no more picking up and hauling around
heavy, bulky supplies.
MFJ-4245MV
MightyLite Switching Power Supply, 45 Amp, 13.8 Vdc .......$149.50
Anderson PowerPole®
Connectors & Crimping Tool
Make power cables you can count on with PowerPole
connectors. Solder or crimp them with the MFJ-7602
crimping tool. Use the 30 amp connectors with #12-16 AWG wire, the 45 amp
connectors with #10-14 AWG wire. Wires smaller than #12 AWG require
soldering. DXE-PW-series color-coded DC power wire is on page 44.
MFJ-11C06
30 Amp Connectors, 6 sets .................................$6.95
DXE-PP30
30 Amp Connectors, 10 sets ............................$12.95
DXE-PP45
45 Amp Connectors, 10 sets ............................$17.95
MFJ-7602
Crimping Tool ....................................................$14.95
WMT-PWR-TOOL Crimping Tool ....................................................$39.95
Power Wire,
2 Conductor Zip Cord
Zip Cord is two-conductor cord which is typically used for
low voltage DC power wiring circuits. The red and black
colors make it simple to identify polarity for DC applications.
DXE-PW-8 Power Wire, 8-gauge ...............per foot $1.49
DXE-PW-10 Power Wire,10-gauge ............per foot $1.19
DXE-PW-12 Power Wire, 12-gauge ...........per foot $0.89
DXE-PW-14 Power Wire, 14-gauge ...........per foot $0.59
DC Power Strips
MFJ-1117 High Current DC
Multiple Outlet Strip
This power strip lets you power four
HF/VHF radios—two at 35 amps each
and two at 35 amps combined—from your transceiver’s main 12 Vdc power supply.
The strip has four pairs of heavy-duty, 35 amp five-way binding posts for your
transceivers. Each pair is fused, RF bypassed, and spaced for standard dual banana
plugs. The unit features a heavy-duty aluminum housing. Six feet of eight gauge
color-coded cable with ring tongue terminals included.
MFJ-1117
High Current Multiple Outlet Strip, 35 Amps Total...................$64.95
MFJ-1124
PowerPole® Power
Distribution Strip
This heavy-duty power
distribution strip has a
total of six outlets.
Outlets 1-4 are
Anderson PowerPole, each rated at 40 amps. Outlets 5 and 6 are 35 amp, high current
binding posts. You can fuse each outlet as needed to protect your accessories or
transceiver. The strip uses widely available ATC/ATO automobile fuses that plug in from
the outside. The fuses can be used for 6, 12, and 24 Vdc systems. The built-in, eightgauge DC input cable is six feet long with 5/16 ring terminals. The RF-tight aluminum
cabinet has mounting ears and a ground post with wing nut. Installed fuses: one each
1 amp, 5 amp, and 40 amp (main), two each 10 amp and 25 amp. Four pairs of 40 amp
PowerPole contacts and five fuses (1 amp, 5 amp, 25 amp, and two 10 amp) included.
MFJ-1124
PowerPole Power Distribution Strip.........................................$64.95
Mail: P.O. Box 1491, Akron, OH 44309 • E-Mail: DXEngineering@DXEngineering.com • Web: DXEngineering.com
7
Station Equipment
MFJ-4125
25 Amp Compact Switching
Power Supply
Station Equipment
Digital Communications Made Easy!
RTTY, PSK-31, CW, SSTV, & More
SignaLink™ PC/Radio
Sound Card Interface
The all-new SignaLink USB combines the legendary
performance of the original SignaLink SL-1+ with a stateof-the-art, built-in low-noise sound card. All sound card
digital and voice modes are supported by the SignaLink
USB. This includes traditional modes such as RTTY, SSTV
and CW, as well as today’s hottest new modes like PSK31, MT-63 and EchoLink®. The front panel controls let you
adjust your Transmit Audio, Receive Audio and Transmit Delay on the fly.
The SignaLink USB needs just one USB connection to the computer and one connection
to the radio (in most cases). Convenient front panel controls make setup and operation
very easy. The SignaLink USB is fully isolated and is compatible with all radio Mic, Data,
and Accessory ports. The SignaLink USB allows you to use your computer’s sound card
for other functions while enjoying digital communications.
Just order the correct, fully-assembled interface cable for your radio(s) and simply “plug
and play.” Cables are available for a Mic connector interface or rear DIN plugs on radios
so equipped. It makes for a neat, clean installation!
• Easy to set up
• Works with all radios
• Just plug in two cables
• Powered through USB cable
• Software included
• Easy hookup to Macintosh or PC
• Built-in sound card
• Comprehensive, easy-to-follow instructions
TGR-SL-USB
SignaLink USB unit...............................................................$89.95
Any cable only $12 95 (except special Elecraft k3 cable)
when ordered with TGR-SL-USB.
Order one cable for each radio.
SignaLink™ Radio Interface Cables
Pick the correct radio interface cable for either a Mic
connector interface or rear DIN plugs on radios so equipped.
Some radios do not have the “RX Audio” signal on the Mic connector and will require a
mono cable to be installed between the SignaLink USB and the radio. This is never an issue
if you attach the SignaLink to your radio’s Data or Accessory port.
TGR-SL-CAB4R
4-Pin Round Mic Connector Interface Cable........................$14.95
TGR-SL-CAB8R
8-Pin Round Mic Connector Interface Cable .......................$14.95
TGR-SL-CABRJ1
RJ-11 Mic Connector Interface Cable...................................$14.95
TGR-SL-CABRJ4
RJ-45 Mic Connector Interface Cable...................................$14.95
TGR-SL-CAB5PD
5-Pin DIN Interface Cable .....................................................$14.95
TGR-SL-CAB8PD
8-Pin DIN Interface Cable .....................................................$14.95
TGR-SL-CAB13I
13-Pin DIN Icom Interface Cable..........................................$19.95
TGR-SL-CAB13K
13-Pin DIN Kenwood Interface Cable...................................$19.95
TGR-SL-CAB6PM
6-Pin Mini-DIN Interface Cable.............................................$14.95
TGR-SL-CABNC
Unterminated Cable Interface Cable .......................................$7.95
TGR-SL-CABK3
Special Elecraft K3 Interface Cable.......................................$24.95
TGR-SLHEAD
Header Plug for Radio Programming .....................................$5.00
Preprogrammed “Plug and Play” Radio Jumper Modules
TGR-SL-MOD13I
Jumper Module, ICOM 13-pin accessory port .......................$7.95
TGR-SL-MOD13K
Jumper Module, Kenwood 13-pin accessory port .................$7.95
TGR-SL-MOD6PM
Jumper Module, 6-pin mini-DIN.............................................$7.95
TGR-SL-MOD8PD
Jumper Module, 8-pin DIN .....................................................$7.95
WMT-RB-AD-CUSB
WMT-CLR-SPKR
WMT-CLR-DSP
Digital Modes +
Rig Control Interface!
West Mountain Radio RIGblaster
Connect the RIGblaster Advantage to your radio’s microphone connector, and a computer
USB connector and you’ll have access to over 100 existing and future ham radio sound
card software programs! You’ll also get over 20 exciting modes that radio could not
otherwise operate. The Advantage also links your computer software and radio using CAT,
CI-V or DB9 interfaces cables.
WMT-RB-AD-CUSB RIGblaster Advantage ..........................................................$189.00
WMT-CIV-CBL
RIG Control Cable for CI-V (Icom & TenTec) Radios...............$9.95
WMT-CAT-6D-CBL
CAT Cable for Yaesu FT-736/747/767/990/1000....................$13.95
WMT-CATMINI-CBL CAT Cable for Yaesu FT-100/100D/817/857/897 ...................$13.95
WMT-58214-1295
Rigblaster DB9F to DB9F Serial Cable ....................................$9.95
West Mountain Radio ClearSpeech Noise Reduction Speaker and Processor
The CLRspkr is a compact, portable loudspeaker containing an adaptive DSP noise
reduction circuit with a 10W audio amplifier. The ClearSpeech™ adaptive DSP algorithms
analyze the noise content of the incoming signal, then attenuate or completely remove
hum, hiss, ignition and power line noise, static and heterodynes. What you hear is clean
voice and CW with over 85% of the noise removed.
If you have an external speaker that you like, the ClearSpeech™ DSP processor unit will
give you the clean sound you want. It installs between your radio and the speaker.
WMT-CLR-SPKR CLRspkr ClearSpeech® DSP Speaker .....................................$199.00
WMT-CLR-DSP
CLRdsp ClearSpeech® DSP Processor...................................$199.00
WMT-DC-SUP-DSP 12 Vdc Power Supply or CLRspkr & CLRdsp ..........................$14.95
West Mountain Radio COMspker Computer Speaker System
This amplified speaker system is optimized for close range operation with any radio
transmitter. It features exceptionally high rejection of Radio Frequency Interference from
1 to 1000 MHz.
WMT-CS1
COMspkr Computer Speaker System .......................................$39.95
About Dummy Loads
The dummy load, or dummy antenna, is a device used in place of an antenna when testing a radio transmitter. It is substituted for an antenna so the
transmitter does not interfere with other radio transmissions. The dummy load absorbs transmitter power and presents the proper load to the transmitter output to prevent damage or
incorrect adjustment. The dummy load should be a pure resistance, representing the ideal impedance of the antenna or transmission line that is used with the transmitter—50 Ω for amateur use. This will provide a standing wave ratio (SWR) of 1:1. The energy absorbed by the dummy load is converted to heat, so you need a dummy load that is rated to safely handle the
amount of power that is delivered by the transmitter.
MFJ Air-Cooled Dummy Loads
Ameritron Oil-Filled Dummy Load, 1.5 kW
• SWR under 1.2:1 to 30 MHz and low SWR to 400 MHz • Heavy-duty 50 Ω resistor
MFJ-260C
Dummy Load, 0-650 MHz, 300 watt ..............................................$39.95
• 7 1/2" H x 6 5/8" D
MFJ-264
Dummy Load, 0-650 MHz, 1.5 kW.................................................$74.95
AME-ADL-1500
Oil-Filled Dummy Load, 1.5 kW................................................$67.95
MFJ-264N
Dummy Load, 0-650 MHz, 1.5 kW, N-connector ...........................$84.95
MFJ-267
Dummy Load/SWR Wattmeter, 0-54 MHz, 1.5 kW ......................$159.95
Vectronics Fan-Cooled Dummy Load, 2,500 Watts, 0-150 MHz
• SWR of less than 1.3:1 at 30 MHz • Resistor Type: Dispersed carbon particles fired in
a ceramic matrix
VEC-DL-2500 Fan-Cooled Dummy Load, 2,500W, 0-150 MHz..............................$194.96
Vectronics Air-Cooled Dummy Load, 1,500W, 0-650 MHz
• SWR: <1.3:1 DC-300 MHz; <1.5:1 300-650 MHz; <2.0:1 650-1,000 MHz
• Resistor Type: Dispersed carbon particles fired in ceramic matrix
VEC-DL650M Air-Cooled Dummy Load, 1,500W, 0-650 MHz .................................$79.95
8
Phone: 800.777.0703 • International: 330.572.3200 • Fax: 330.572.3279 • DoD CAGE Code: 3M3H7
MFJ SWR/Wattmeter, 1.8-30 MHz
MFJ Auto Ranging SWR/Wattmeter, 1.8-60 MHz
This auto ranging, microprocessor-controlled wattmeter has a giant 6
1/2" (diagonal) meter scale. It has 20/200/2,000 watt ranges with true
peak, average forward, and reflected power modes plus fully automatic
SWR readings. Other features include an amplifier bypass control and
control relay for high SWR, field-upgradeable firmware, and high SWR
audio and visual alarms. Measures 7" W x 5 1/2" H x 5" D.
MFJ-869
Auto Ranging SWR/Wattmeter...............................................$219.95
MFJ-1312D
Power Supply, 12 Vdc/500 Milliamp ........................................$15.50
MFJ-108B LCD 12/24 Dual Clock
This dual-display LCD clock displays 12/24 hour time
simultaneously! Mounted in a brushed aluminum frame, the
clock features large 5/8 inch LCD numerals and a sloped face
that makes it easy to read from across the room. You can synchronize the two clock faces
to WWV for split-second timing. The clock has quartz movements for excellent accuracy.
Long-life batteries included. The clock measures 4.5W x 2.5H x 2D inches
MFJ-108B
LCD 12/24 Dual Clock .............................................................$21.95
MFJ-121B
Dual Time Zone Atomic Clock
Read both UTC and local time at a glance with this dual atomic clock.
It displays 12 and 24 hour time simultaneously—each can be independently set. Daylight savings time can be disabled. The automatic backlight is activated
daily at your preset time and stays on for 8 hours. The display has huge 2" tall by 1" wide
LCD numerals, an exclusive UTC zone, and a running seconds display. 11 3/8" W x 7 1/4" H
x 1" D, wall- or desk-mountable. Runs on four ‘AA’ batteries (not included).
MFJ-121B
Dual Time Zone Illuminated Atomic Clock ...............................$79.95
Vibroplex Keys
and Accessories
Vibroplex has been a leading manufacturer of quality CW keys
and amateur radio accessories for over 100 years.
From the Original Bug (in continuous production
since 1905) to the always-reliable straight key, we
offer a wide selection of dependable models to choose
from. Over 300,000 Vibroplex keys are in circulation today
because of their durability and unwavering performance.
Keys
VIB-BLRACER-STD
Blue Racer...........................................................................$219.95
VIB-CODEWARR-JR Black Code Warrior Jr. ..........................................................$99.95
VIB-IAMBIC-S
Iambic Paddle Standard......................................................$149.95
VIB-IAMBIC-D
Iambic Paddle Deluxe .........................................................$189.95
VIB-IAMBIC-P
Iambic Paddle Presentation ................................................$289.95
VIB-IAMBIC-G
Iambic Paddle Gold.............................................................$309.95
VIB-VIBROKEYER-S Vibrokeyer Single Paddle Standard ....................................$149.95
VIB-VIBROKEYER-D Vibrokeyer Single Paddle Deluxe ........................................$189.95
VIB-VIBROKEYER-G Vibrokeyer Single Paddle Gold ...........................................$309.95
VIB-ORIGINAL-S
Original Bug Standard.........................................................$199.95
VIB-ORIGINAL-D
Original Bug Deluxe ............................................................$259.95
VIB-ORIGINAL-P
Original Bug Presentation ...................................................$339.95
VIB-ORIGINAL-G
Original Bug Gold................................................................$379.95
VIB-HK-STD
Straight Key Standard.........................................................$149.95
VIB-HK-DELUXE
Straight Key Deluxe Chrome...............................................$189.95
VIB-HK-GOLD
Straight Key Gold................................................................$309.95
Accessories
VIB-DC-VIBRO
Dust Cover for HK/Iambic/Vibrokeyer.........................................$34.95
VIB-DC-ORIG
Dust Cover for Original Bug ......................................................$35.95
VIB-DC-RACER
Dust Cover for Racer.................................................................$29.95
VIB-CP-2
2-Conductor Cable 1/4" Plug (Bug or Hand Key)........................$9.95
VIB-CP-3
3-Conductor Cable 1/4" Plug (Paddles).......................................$9.95
VIB-CP-3-3-5MM 3-Conductor Cable 3.5mm Plug (Paddles); ................................$9.95
MFJ-130BRC
Calendar/Time/Temp Atomic Clock
Metallic blue/silver clock has a giant 8 1/2" x 9" LCD display with 2 1/4" tall
time digits with month/date/day and indoor temperature displayed below.
Auto daylight savings time can be turned off when setting clock for UTC.
Running seconds display. Temperature displayed in Fahrenheit. 10 3/4" W x 6" H x 3/4" D,
wall- or desk-mountable. Runs on two ‘AA’ batteries (not included).
MFJ-130BRC
Calendar/Time/Temp Clock .......................................................$24.95
MFJ-133RC
Compact Dual Time Zone Atomic Clock
This compact (4" W x 3" H x 3/4" D) clock folds up and slides in your
shirt pocket. It lets you read any two time zones in 12 or 24 hour
format, and is atomic-controlled for absolute pin-point accuracy. The
large 1 1/8", high-contrast LCD numerals are easily read from 6 feet away.
MFJ-133RC
Compact Dual Time Zone Atomic Clock..................................$34.95
QSL 7"
Digital Picture
Frame and Scanner
This kit, consisting of one
digital scanner and one 7"
digital picture frame, is the
perfect way to digitally capture
and display your QSL Cards or
4" x 6" photos.
Simply feed your QSL cards
through the scanner, then
transfer the scanner’s SD
memory card to the digital
picture frame. It’s a great way to preserve the cards and remember QSOs, while showing
off your collection. Over 3,000 QSL cards can be stored and displayed. The XYL will be
happy to see the wall again, and you’ll have more room to hang certificates!
Limited time offer—includes a FREE 2 GB SD memory card
DXE-QSL-KIT........................................................................................................$89.95
Bencher Keys
and Accessories
Equip your station with the performance
of Bencher keys and accessories. All
Bencher products are fabricated and assembled
by skilled professionals in the USA, using the finest
materials for superior performance and durability.
Keys
BNR-RJ-1
Hand Key, black base..........................................................$115.00
BNR-RJ-2
Hand Key, chrome base ......................................................$147.00
BNR-BY-1
Iambic Paddle, black base/chrome parts............................$115.00
BNR-BY-2
Iambic Paddle, chrome base and parts ..............................$147.00
BNR-ST-1
Single Lever Paddle, black base/chrome parts;..................$115.00
BNR-ST-2
Single Lever Paddle, chrome base and parts .....................$147.00
Accessories
BNR-EZ-1
4 ft. Hook-Up Cable Kit, 1/8" & 1/4" plugs............................$10.95
BNR-YA-1
Low Pass Filter, 1.8 to 29.7 MHz..........................................$95.00
VIB-DC-BY
Dust Cover for BY Paddles ...................................................$34.95
MFJ Millennium
CW Memory Keyer
Send clear, precise code every time with the MFJ Millennium CW Memory Keyer. It
features dual microprocessors, a nonvolatile EEPROM chip and an easy-to-read LCD
message display for unmatched CW operation. The keyer has 32 message memories
(stores up to 8,000 characters) easily loaded by paddle, keyboard or from a computer
with a terminal program. The keyer can repeat messages continuously and also insert
timed pauses, auto-incrementing serial numbers and embedded commands.
MFJ-495
Millennium CW Memory Keyer .........................$179.95
Mail: P.O. Box 1491, Akron, OH 44309 • E-Mail: DXEngineering@DXEngineering.com • Web: DXEngineering.com
9
Station Equipment
The world’s largest HF SWR/wattmeter with a giant 6 1/2" (diagonal)
meter scale! You get ultra-fine resolution with big high-contrast
numbers to make reading a breeze, even from across your shack.
MFJ’s exclusive TrueActive™ peak reading circuit captures true peak or
average forward and reflected power readings. The 20/200/2,000 watt
ranges make this meter valuable for QRP or QRO operation. Measures 7" W x 5 1/2" H x 5" D.
MFJ-868
HF SWR/Wattmeter ................................................................$149.50
MFJ-1312D
Power Supply, 12 Vdc/500 Milliamp ........................................$15.50
Ameritron Power Amplifiers
Station Equipment
Ameritron Power Amplifiers
AL-811 600 Watt HF Amplifier,
Three 811A Tubes
The AL-811 gives you 600 watts PEP
output—nearly 2 full S-units over your
barefoot rig. That could mean the difference
between hearing “you’re Q-5 armchair copy”
and “Sorry can’t copy you, too much QRM.”
Now you won’t have to stand aside while the
“big guns” steal your DX—you’ll be able to log
some of those stations first. Going from 600
watts to the full legal limit (1,500 watts) gives you less than one S-unit increase and can
cost three or four times more money. Get this amplifier and you’ll get a powerful punch at
a price that’s easy on your wallet.
AME-AL-811
US version .............................................................................$709.00
AME-AL-811XCE
Export only version................................................................$769.00
AL-811H 800 Watt HF Amplifier,
Four 811A Tubes
This amplifier gives you 800 watts PEP output
for that extra punch you need to be heard
when a 100 watt transceiver isn’t enough. Only
Ameritron gives you four fully neutralized 811A
transmitting tubes. You get absolute stability and
superb performance on higher bands that can’t be
matched by un-neutralized tubes.
AME-AL-811H
US version ................................................................................$859.00
AME-AL-811HXCE Export only version...................................................................$919.00
AME-AL-811HD
US version, heavy duty .........................................................$1,099.00
AME-AL-811HDXCE Export only version, heavy duty............................................$1,295.00
AL-572 1,300 Watt HF Amplifier,
Four 572B Tubes
The Ameritron AL-572 is a 1,000 watt
CW/1,300 watt PEP (nominal output power)
linear amplifier that operates on all amateur
bands from 160 through 15 meters (and WARC
bands and ten meters with reduced performance). It
uses four 572B tubes in a class AB2 grounded grid circuit. The amplifier is factory wired for
120 volt, 50/60 Hz AC line voltage. It easily converts to other supply voltages between 90
and 250 volts AC.
AME-AL-572 Free UPS Ground Shipping! .............................................................$1,679.00
AL-80B 1 kW HF Amplifier,
One 3-500Z Tube
You get up to a full kilowatt PEP output and
nearly 70% efficiency from this whisper-quiet
desktop linear amplifier. It covers all bands
from 160 through 15 meters, including WARC
and MARS. You get up to 1,000 watts output
on SSB, 800 watts output on CW, and 500
watts output on RTTY. Other features include an
extra heavy-duty power supply, a genuine
3-500 tube, tuned input, Pi/Pi-L output, inrush current protection, multi-voltage transformer, dual cross-needle meters, and QSK compatibility. It’s made in the USA and has a
two year warranty. Modification instructions for operation on 10 and 12 meters are available
with proof of a valid amateur radio license.
AME-AL-80B.............................................................................................................$1,329.00
AL-800H 1.5kW+ HF Amplifier,
Two 3CX800 Tubes
The AL-800H is a 1,500 watt output linear
amplifier that operates from 160 through
15 meters. It uses a pair of 3CX800A7
tubes in a class AB2 grounded grid circuit.
The AL-800H is factory wired for 240 volt,
50/60 Hz AC line voltage. It is easily
converted to other supply voltages between
90 and 250 volts AC. Modification instructions for operation
on 10 and 12 meters are available with proof of a valid amateur radio license.
AME-AL-800H Free UPS Ground Shipping! ..........................................................$3,549.00
AL-1200 1,500 Watt HF Amplifier,
One 3CX1200A7 Tube
The AL-1200 is a 1,500 watt output linear
amplifier that operates from 160 through
15 meters. It uses a single 3CX1200A7
tube in a class AB2 grounded grid circuit.
CW FM and RTTY efficiency is improved
by shifting the bias deeper into class B.
The heavy-duty power supply and RF
components, combined with a forced air
system using chimneys, provide long service
life. The AL-1200 is factory wired for a 240 volt, 50/60 Hz line voltage. It features a super
heavy-duty power supply that loafs at full legal power—it can deliver more than 2,500 watts
PEP two tone output for a half-hour!
AME-AL-1200 Free UPS Ground Shipping! ...........................................................$2,999.00
ALS-500MR 500 Watt HF Mobile
Amplifier/Remote Combo
The ALS-500MR combines the ALS-500M
amplifier with the ALS-500RC remote
control unit. It is a 500 watt PEP output,
solid state linear amplifier that uses
rugged, conservatively rated bipolar RF
devices in the power output section.
AME-ALS-500MR ........................................................................................................$819.00
ALS-1300 1200 Watt Solid State Amp
with AC Power Supply
The Ameritron ALS-1300 is a 1,200 nominal
watt output, solid state, linear amplifier
which provides continuous frequency
coverage from 1.5 through 22 MHz
(160 through 15 meters) with no tuning
adjustments. An AME-MOD-10MK
modification kit is available to extend
operation up to 30 MHz with a copy of a
valid amateur license. The matching separate power supply, ALS-1300SPS, is shipped factory
wired for 220 volt, 50/60 Hz power mains and is easily converted to 110 volts.
AME-ALS-1300 Free UPS Ground Shipping!.........................................................$2,375.00
AL-82 High Power HF Amplifier,
Two 3-500Z Tubes
The AL-82 is designed to give you years
of trouble-free service at the full legal
output power limit. It features a 1,800 watt
continuous, commercial rated Hypersil
transformer with heavy duty rectifiers and
AL-800 1.25 kW HF Amplifier,
computer capacitors in a full wave bridge
One 3CX800 Tube
supply. Two bias settings allow either high
The AL-800 is a 1,200 watt PEP output
efficiency RTTY and CW operation at 1,500 watts of output at nearly 70% plate efficiency,
linear amplifier that operates from 160
or low distortion 1,500 watts PEP, SSB, or SSTV output. The tuning capacitors and
through 15 meters. It uses a single
bandswitch have a 35% safety factor to virtually eliminate tank circuit component failures,
3CX800A7 tube in a class AB2 grounded
even under adverse operating conditions.
grid circuit. The AL-800 is factory-wired for
120 volt, 50/60 Hz AC line voltage. It is easily
The cooling system keeps the components and tubes safely below the manufacturer’s
converted to other supply voltages between 90 and
ratings, even while operating at 1,500 watts output with a steady carrier. The filament
250 volts AC. Modification instructions for
supply has inrush current limiting to ensure maximum tube life. Shielding and bypassing
operation on 10 and 12 meters are available with proof of a valid amateur radio license.
help prevent TVI and RFI at high power levels.
AME-AL-800 Free UPS Ground Shipping! .............................................................$2,349.00
AME-AL-82 Free UPS Ground Shipping! ...............................................................$2,459.00
Free UPS Ground Shipping applies to Domestic United States only.
10
Phone: 800.777.0703 • International: 330.572.3200 • Fax: 330.572.3279 • DoD CAGE Code: 3M3H7
Ameritron Power Amplifiers
ALS-500M 500 Watt HF Mobile Amplifier,
Remote Ready
The ALS-500M is a 500 watt PEP output,
solid state linear amplifier that uses rugged,
conservatively rated bipolar RF devices in the
power output section. The ALS-500M operates
at full power with continuous frequency coverage from 1.5 through 21.6 MHz (160 through
15 meters). This amplifier requires no tuning adjustments. The amplifier is set up for use with
Ameritron’s ALS-500RC remote control unit. A modification kit (AME-MOD-10M) is available
to extend operation to 30 MHz with proof of a valid amateur radio license.
AME-ALS-500M ...........................................................................................................$779.00
ALS600 600 Watt HF Amplifier with AC Power Supply
The ALS-600 is a 600 nominal watt output, solid
state linear amplifier that features state-of-the-art,
high-voltage, RF TMOS FET devices in the power
output section. The ALS-600 provides continuous
frequency coverage from 1.5 through 22 MHz (160
through 15 meters) with no tuning adjustments.
The matching AC power supply is factory wired for 120
volt, 50/60 Hz line voltage and is easily converted
to other supply voltages between 100 and 240 volts. A modification kit (AME-MOD-10M) is available to extend operation to 30 MHz with proof of a valid
amateur radio license.
AME-ALS-600...........................................................................................................$1,269.00
ALS-600S 600 Watt HF Amplifier with Switching AC Power Supply
The ALS-600S is a 600 nominal watt output, solid state
linear amplifier that features state-of-the-art, high-voltage,
RF TMOS FET devices in the power output section. The
ALS-600S provides continuous frequency coverage from
1.5 through 22 MHz (160 through 15 meters) with no
tuning adjustments. Broadband five-pole low pass filters
provide output harmonic suppression in excess of all FCC
requirements.
The matching switching AC power supply is factory wired
for 120 volt, 50/60 Hz line voltage and is easily converted to other supply voltages between
90-130 and 185-260 volts. A modification kit (AME-MOD-10M) is available to extend
operation to 30 MHz with proof of a valid amateur radio license.
AME-ALS-600S ........................................................................................................$1,369.00
Ameritron
Inrush Current Protection
When you first turn on your amplifier, the
extra current draw can cause your house
lights to flicker and your amplifier may
emit a loud “thump.” This terrible
inrush current stresses all your power
supply components to their limits.
AMR-ICP-240
Additionally, your cold tube
AMR-ICP-120
filament can suffer abusive thermal shock.
Ameritron’s Step-Start Inrush Current Protector
stops damaging inrush current. By starting
your linear amplifier through a high-power current-limiting resistor, then shorting the
resistor with a relay, you get a startup sequence that is easy on your tube and power supply
components. Installation is easy, with no complicated wiring. You don’t even have to take
the cover off–just plug your amplifier power cord into the Ameritron Inrush Current
Protector and it’s ready to go. It works with nearly all linear amplifiers.
AME-ICP-120
Inrush Current Protection, 120 V .............................................$79.95
AME-ICP-240
Inrush Current Protection, 240 V .............................................$79.95
Ameritron
QSK Amplifier Switch
Enjoy full break-in CW with any amplifier.
The QSK-5 is six times faster than a
typical mechanical vacuum relay “QSK”
switch, and unlike those slower switches,
it doesn’t use noisy mechanical relays. That helps
eliminate annoying relay chatter, making the QSK-5 extremely quiet! The QSK-5 is also universal, so you can keep using it even when you change station equipment.
AME-QSK-5..................................................................................................................$399.95
Ameritron
Universal Amplifier Buffer
Protect your transceiver from too much relay
voltage, spikes, or excessive current on the relay
control line with Ameritron’s Universal Amplifier
Buffer. It’s compatible with all common radios and
amplifiers. Virtually any radio can operate the ARB-704; DX Engineering carries
radio-specific accessory cables that provide a complete plug-and-play installation.
AME-ARB-704 ................................................................. ..............................................$57.95
Ameritron
13.8 Vdc Switching Power Supply
The SPS-75MV Ameritron 75 Amp Switching Power
Supply is the perfect match for Ameritron’s ALS500M, 500 Watt solid state amplifier. It provides
75 amps output current continuously!
The unit also features:
• Reverse polarity protection
• Brown out input protection
• Over-current, over-temperature protection
• A thermally-controlled quiet fan
Output voltage is variable with metering for both
voltage and current. Input voltage is 108-132 Vac,
50/60 Hz, and the unit draws 11 amps.
AME-SPS-75MV ..........................................................................................................$259.95
Ameritron
Power Amplifier Accessories
Amplifiers
AME-ARB-704
AME-ARB-704I2
Interface Cables
AME-PNP-13D
AME-PNP-5M
AME-PNP-7D
AME-PNP-8D
AME-PNP-8M
AME-PNP-8MK
Accessories
AME-QSK-5
AME-ALS-500RC
AME-MOD-10M*
AME-MOD-10MB*
Universal Amplifier Buffer, for all transceivers .............................$57.95
Amplifier Interface for Icom 706/7000.........................................$57.95
704 to IC-706/7000.......................................................................$16.95
704 to FT-847 Yaesu.....................................................................$16.95
704 to TS-440/690/450/180/140/950/130/870 and Kenwood ....$16.95
704 to FT-1000/900/767/920/990/747 Yaesu ..............................$16.95
704 to FT-890/840/817 Yaesu ......................................................$16.95
704 to 8-Pin Mini, TS-480 Kenwood..........................................$16.95
QSK Amplifier Switch.....................................................................$399.95
Remote Head for ALS-500M, S/N 13049 and above ......................$48.95
10 Meter Mod Kit for ALS-600/600S/ALS-500M ............................$27.95
10 Meter Mod Kit for ALS-600/600S,
serial number 12522 & up...............................................................$27.95
AME-MOD-10MK* 10 Meter Mod Kit for ALS-1300 .... ..............................................$37.95
AME-SPS-75MV
Switching Power Supply, 75 amp continuous, 13.6 Vdc..............$259.95
DXE-DCB-36
Dual Shielded Cable with RCA connectors, 3 ft...................................$3.99
DXE-DCB-72
Dual Shielded Cable with RCA connectors, 6 ft...................................$5.99
* Requires proof of Amateur License
Mail: P.O. Box 1491, Akron, OH 44309 • E-Mail: DXEngineering@DXEngineering.com • Web: DXEngineering.com 11
Station Equipment
AL-1500 High Power HF Amplifier,
One 3CX1500/8877 Tube
The AL-1500 will deliver 1,500 watts CW
output with only 65 watts drive. It features
the Herculean Eimac 3CX1500/8877 tube for
continuous, full legal output with minimum
exciter wear. The AL-1500 also features
time delay starting to protect the tube and
over-current shut off to remove the drive if mistuned. A commercial-grade, die-cast ball
bearing blower provides quiet operation at full rated airflow to maximize tube life.
AME-AL-1500 Free UPS Ground Shipping! ...........................................................$3,299.00
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising