KIDFIX XP KIDFIX XP SICT

KIDFIX XP KIDFIX XP SICT
PAGE I
2. INTRODUCTION
3. Certification
We are delighted that our KIDFIX XP / KIDFIX XP SICT can safely accompany your child through a new stage in its life.
1. PRODUCT OVERVIEW
In order to protect your child correctly, the KIDFIX XP/ KIDFIX XP SICT
must always be used and installed as described in these instructions.
If you have any further questions regarding its use, please feel free to contact us:
BRITAX RÖMER
Kindersicherheit GmbH
Blaubeurer Straße 71
D-89077 Ulm
Germany
BRITAX EXCELSIOR
LIMITED
1 Churchill Way West
Andover
Hampshire SP10 3UW
United Kingdom
12
03
04
13
Symbol
14
10
05
06
01
02
T.: +49 (0) 731 9345-199/-299
F.: +49 (0) 731 9345-210
E.: service.de@britax.com
www.britax.eu
Group
Body weight
II+III
15 to 36 kg
*ECE = European Standard for Child Safety Equipment
The child safety seat has been designed, tested and certified according to
the requirements of the European Standard for Child Safety Equipment (ECE
R 44/03). The seal of approval E (in a circle) and the approval number are
located on the orange approval label (sticker on the child safety seat).
T.: +44 (0) 1264 333343
F.: +44 (0) 1264 334146
E.: service.uk@britax.com
www.britax.eu
Keyword
Explanation
DANGER!
Risk of severe personal injury
WARNING!
Risk of minor personal injury
CAUTION!
Risk of material damage
TIP:
Useful notes
Instructions that follow a set sequence are numbered.
Example:
1. Press the button...
09
KIDFIX XP
Testing and certification
In accordance with ECE* R 44/04
KIDFIX XP SICT
These instructions use the following symbols stated below:
11
BRITAX RÖMER
Child safety seat
DANGER! This approval will be invalidated if you make any modifications
to the child safety seat. Only the manufacturer is permitted to
make modifications to the child safety seat. The child seat is
approved for use both with and without XP-PAD.
WARNING! Use the KIDFIX XP / KIDFIX XP SICT exclusively for securing your child in your vehicle. It is in no way suitable as a
seat or toy in the home.
DANGER! Never secure your child or the child safety seat with a 2-point
belt. If you secure your child in the child seat with only a
2-point belt, then in the event of an accident this may cause
serious injuries to your child, possibly resulting in death.
07 08
16
02
03
04
ISOFIX fastening points (vehicle)
ISOFIX insert guides
Belt holder (dark red)
XP-SICT (only KIDFIX XP SICT)
05
06
07
08
Belt guide (bright red)
ISOFIT locking arms
Release knob
Safety button
09
10
11
12
ISOFIT settings key
Seat cushion
XP-PAD
Adjusting handle of the headrest
13
14
Storage compartment
Backrest
4. USE IN THE VEHICLE
5. CARE AND MAINTENANCE
Please observe the instructions for using children's restraining systems in the operating
instructions of your vehicle. The seat can be used in vehicles with ISOFIX anchoring systems
(see type list) and in vehicles with a 3-point belt.
Please ensure that you only use the original BRITAX RÖMER replacement seat
covers, as the seat cover is an integral part of the child safety seat and fulfils important functions to ensure the smooth operation of the system. Replacement seat
covers are available from your dealer or from an ADAC office.
• The cover can be removed and washed with a mild detergent in the delicates
programme of the washing machine (30 °C). Please observe the instructions
on the washing label of the cover.
• The plastic parts and the XP-PAD can be cleaned with a soap sud. Do not use
any caustic cleaning agents (such as solvents).
DANGER! The child seat must not be used without the seat cover.
Please find the information on the seats approved for child safety seats of the weight classes 15 to
36 kg in the operating instructions of your vehicle.
The KIDFIX XP / KIDFIX XP SICT is approved for two different methods of installation:
Symbol
Installation type
Approval type
with the ISOFIT locking arms on the
ISOFIX fastening points in the vehicle. Observe the vehicle type list.
semi-universal
with the vehicle's 3-point seatbelt
universal
Section
a)
9A
19
You can use your child safety seat as follows:
Against the direction of travel
no 1)
with 2-point belt
no
with 3-point belt
2)
with ISOFIX fastening points
(between seat surface and
backrest)
on front passenger seat
Yes
on outer rear seat
Yes
on centre rear seat (with
3-point belt)
19
Yes
11
2.
3.
4.
5.
position.
Unhook the cover hook 19 on the rear of the backrest.
Remove the top part of the cover and fold it forwards to
the seat surface.
Unhook the cover hook 19 on the front of the backrest.
Pull the cover off of the seat surface.
03
07
08
Removing the headrest cover
6. Unhook the cover loop 20 on the rear of the backrest.
Yes
15–36 kg
Yes
REMOVAL:
Removing the seat cover
1. Moving the headrest of the vehicle seat into the top
vehicle type list enclosed. This type list is consistently kept up to date. The latest version
can be obtained from us or from www.britax.eu / www.roemer.eu.
Yes
UNFASTENING YOUR CHILD:
1.To unfasten your child, use the release button of your vehicle seat buckle.
TIP! The XP-PAD can remained applied for easier use on the diagonal
belt of your vehicle, the diagonal belt must be retensioned before every
journey; see: Section10 step 12 [page II].
16
9B
a) This means that the child safety seat may only be used in vehicles that are listed in the
In the direction of travel
6. DISASSEMBLY AND DISPOSAL
20
3)
4)
1) Use is permitted on a rearward-facing vehicle seat (e.g. in a van or minibus) only
if the vehicle seat is also approved for use by adults. The seat may not be in the area of effect
of an airbag.
2) The safety belt must be approved to ECE R 16 or a comparable standard (see test label on
belt with an "E" or "e" in a circle).
3) If there is a front airbag: Slide the vehicle seat a long way back and refer to any instructions
in vehicle owner's manual.
4) Cannot be used if the vehicle seat is equipped with only a 2-point belt.
7. Unhook the cover hook 19 on the front of the backrest.
8. Pull off the cover of the headrest 22 .
►►The cover can now be washed. Please observe the
instructions on the washing label of the cover:
22
Re-fitting the cover
KIDFIX XP
KIDFIX XP SICT
DISPOSAL:
Please observe the waste disposal regulations in your country.
Disposal of packaging
Container for cardboard boxes
Seat cover
Residual waste, thermal utilisation
Plastic parts
According to the labelling in the
corresponding container
Metal parts
Container for metals
Belt straps
Container for polyester
buckle and tongue
Residual waste
GB
User instructions
DANGER! the child safety seat must always be
secured when it is in the vehicle, even if no child is
being transported.
Proceed in reverse order to put on the cover.
19
1.Operate the release key of your vehicle seat buckle
2.Open the XP-PAD 11 on the Velcro fastener and
remove the diagonal belt 16 .
3.Open the dark red belt holder 03 by pressing backwards the key on the belt holder 03 and unthreading the diagonal belt 16 .
Only for installation type A (ISOFIT):
4.To release the ISOFIT fastening, release the green
safety button 08 and the red release button 07 first
on the one and the on the other side opposite on
another.
►The
►
child safety seat can now be removed.
15 kg - 36 kg
(~4 Y - 12 Y)
2000010039 05/16
01
Belt guide colours
For better differentiation, the two vehicle seat
belts are highlighted in different colours. The diagonal seat belt 16 in dark red and the lap belt
15 in bright red. The colour of the belt guides
on the child safety seat follows the same colour
15
scheme.
www.britax.eu
PAGE II
7. SAFETY NOTES
Please take the time to read these instructions carefully and keep
them to hand in the intended storage compartment 13 on the child
safety seat at all times! The instructions must be with the child safety
seat if the latter is passed on to a third party.
DANGER! For the protection of your child:
• In the event of an accident with a collision speed of more than 10 km/h, the
child safety seat may be damaged without the damage becoming immediately visible. In this case the child safety seat must be replaced. Please
dispose of it properly.
• Have your child safety seat checked as a rule if it was damaged (e.g if it
falls to the ground).
• Regularly check all important parts for damage. Ensure that all mechanical
parts, in particular, are fully functional.
• Never lubricate or oil parts of the child seat.
• Never leave your child unattended in the child seat in the vehicle.
• Let your child in and out of the vehicle from the pavement side as a rule.
• Protect the child safety seat against intensive direct sun radiation,
as long as it is not in use. The child safety seat can become very hot
under direct sun radiation. Child skin is sensitive and could thereby
be injured.
• The more snugly the harness fits over your child's body, the better your will be
protected. Therefore avoid putting thick clothes on your child under the belt.
• Take regular breaks on long journeys in order to give your child the opportunity to play around.
• Use on the rear seat: Push the front seat forwards sufficiently so that the
feet of your child do cannot hit the backrest of the front seat (to avoid the
risk of injury).
DANGER! For the protection of all vehicle occupants:
In the case of an emergency stop or an accident, unsecured persons or
objects may cause injury to other vehicle occupants. Please always check
that...
• the backrests of the vehicle seats are locked (i.e. that a foldable rear seat
bench latch is engaged).
• all heavy or sharp-edged objects in the vehicle (e.g. on the parcel shelf) are
secured.
• all persons in the vehicle have their seatbelts fastened.
• the child safety seat is always secured when it is in the vehicle, even if no
child is being transported.
A
With ISOFIT + 3-point belt
The KIDFIX XP / KIDFIX XP SICT is installed permanently in the vehicle with the
ISOFIT locking arms.
Your child is then buckled into the child seat with the vehicle's 3-point seatbelt.
01
CAUTION! To protect your vehicle:
• Certain car seat covers made from more sensitive materials (e.g. velour, leather, etc.) may sustain signs of wear and tear when using child safety seats. For the
optimum protection of your car seat covers, we recommend using the BRITAX
RÖMER child safety seat surface from our accessories programme.
TIP! The ISOFIX fastening points are located between the surface and the backrest of the vehicle seat.
* The insert guides facilitate the installation of the child safety seat with the use of the
SOFIX fastening points and prevent damage to the car seat covers. As long as they
are not used, remove them and keep them in a safe place. For vehicles with foldable
a backrest, the insert guides need to be removed before folding the backrest. Any
problems occurring usually come from soiling or external objects on the insert guides
and on the hook. Remove soiling or external objects to rectify such problems.
2. Moving the headrest of the vehicle seat into the top position.
3. Carry out the steps in Section 8 „ADJUSTING THE HEADREST“.
4. Hold the ISOFIT settings button 09 down and push the ISOFIT locking
arms 06 out in full .
09
06
07
22
For the safety of your child, before every journey in the car check
that...
►the
► child safety seat is slotted in on both sides with the ISOFIT locking
arms 06 in the ISOFIT fastening points 01 and both safety buttons 08 are
fully green;
►the
► child safety seat is securely fastened;
►the
► lap belt 15 runs in the bright red belt guides on both sides of the seat
cushion 05 ,
►the
► diagonal seat belt section 16 on the side of the vehicle seatbelt buckle
18 also runs through the light red belt guide 05 of the seat cushion,
►the
► diagonal seat belt section 16 runs through the dark red belt holder 03
of the headrest,
►XP-PAD
►
11 and XP-SICT 04 are correctly installed and used,
►the
► diagonal seat belt section 16 runs diagonally backward,
►the
► straps are tight and not twisted,
►The
►
seatbelt buckle 18 must not be positioned on the red belt guide 05 in
the seat cushion.
DANGER! If your child tries to open the SOFIT safety buttons 08 or the vehicle belt buckle 18 , stop immediately as soon as possible. Check whether
the child safety seat is correctly fastened and ensure that your child is correctly secured. Explain to your child the dangers associated with his actions.
B
7.Guide the elastic holding strap of the XP-PAD 11
into the dark red belt holder 03 of the headrest 22
until it lies completely in the belt holder 03 and is
not twisted.
14
03
With 3-point belt
11
9. Position the two ISOFIT locking arms 06 directly in
front of the two insert guides 02 .
02 06
10. Push both ISOFIT locking arms 06 into the insert
guides 02 until the ISOFIT locking arms 06 engage on both sides with a clicking sound.
DANGER! The green safety button 08 must be
visible on both sides so that the child
safety seat is correctly fastened.
1.Reach into the adjustment handle 12 on the back of
the headrest 22 and pull it towards you.
This unlocks the headrest.
2.You can now move the unlocked headrest 22 to
the desired height. As soon as you release the
adjustment handle 12 , the headrest 22 will lock
into place.
3.Place the child safety seat on the vehicle seat.
4.Have your child sit down in the child safety seat and
check the height. Repeat the procedure until the
headrest 22 has the correct height.
11. Hold the ISOFIT settings button 09 down and push
the child safety seat as far back as possible.
09
08
14
03
8. Place the child safety seat in driving direction
on a vehicle seat approved for use.Ensure that
the backrest 14 is flush with the backrest of the
vehicle seat .
Unscrew the XP-SICT 04 anti-clockwise (on the side closer to the vehicle door) until it has a distance of 5 mm to the
vehicle door or has been unscrewed to the maximum.
KIDFIX XP SICT & KIDFIX XP:
11
18
16
15
05
To unfasten your child or to remove the child safety seat, observe the
steps in Section 6 „REMOVAL“ [PAGE I]
11
11
KIDFIX XP SICT:
UNFASTENING YOUR CHILD AND REMOVAL:
6. Place the XP-PAD 11 on the side of the child safety
seat closer to the vehicle door.
08
To adjust the height of the headrest to fit your child:
22
5. Push the green safety button 08 and the red
release button 07 on both sides of the seat towards
each other. This ensures that both hooks on the
ISOFIT locking arms 06 are open and ready to use.
10. SECURING YOUR CHILD
04
The KIDFIX XP / KIDFIX XP SICT is not installed permanently in the vehicle. It
is simply secured together with your child using the vehicle's 3-point seatbelt.
8. ADJUSTING THE HEADREST
A correctly set headrest 22 ensures that the diagonal seat belt section 16 is
optimally positioned, and gives your child optimum protection.
The headrest 22 must be adjusted so that there is a space two fingers wide
between the headrest 22 and your child's shoulders.
02
1. If your vehicle is not fitted with ISOFIX insert guides by standard, clamp
the two insert guides 02 , with are included in the scope of delivery of
the seat*, with the section pointing upwards to the two ISOFIX fastening
points 01 of your vehicle.
WARNING! For your protection when handling the child seat:
• Never use the child safety seat free-standing, not even for test sitting.
• When swivelling up the backrest 14 , nothing must come between the backrest 14 and the seat cushion 10 . You or your child could pinch your fingers,
injuring them.
• To avoid damage, ensure that the child safety seat is not jammed in between
hard objects (car door, seat rails, etc.).
• Keep the child safety seat in a safe place if it is not in use. Do not place any
heavy objects on the seat and do not store it directly next to sources of heat or
in direct sunlight.
12
12. Shake the child safety seat to ensure that it is
securely fastened and check again the fastening
buttons 08 to ensure that both are fully green.
13. Carry out the steps in Section 10 „SECURING
YOUR CHILD“.
9. INSTALLATION
11
1.Carry out the steps in Section 8 „ADJUSTING THE
HEADREST“.
2.Place the XP-PAD 11 on the side of the child safety
seat closer to the vehicle door.
3.Guide the elastic holding strap of the XP-PAD 11
into the dark red belt holder 03 of the headrest 03
until it lies completely in the belt holder 03 and is
not twisted.
4.Place the child seat on the vehicle seat. Ensure that
the backrest 14 is flush with the backrest of the
vehicle seat.
Tip! If the headrest of the vehicle seat gets in the
way, turn it the other way.
5.Carry out the steps in Section 10 „SECURING
YOUR CHILD“.
For the safety of your child, before every journey in the car check
that...
►the
► child safety seat is securely fastened;
►the
► lap belt 15 runs in the bright red belt guides on both sides of the seat
cushion 05 ,
►the
► diagonal seat belt section 16 on the side of the vehicle seatbelt buckle 18 also runs through the light red belt guide 05 of the seat cushion,
►the
► diagonal seat belt section 16 runs through the dark red belt holder 03
of the headrest,
►the
► diagonal seat belt section 16 runs diagonally backward,
►the
► straps are tight and not twisted,
►XP-PAD
►
11 and XP-SICT 04 are correctly installed and used,
►the
► seatbelt buckle 18 must not be positioned on the red belt guide 05 in
the seat cushion.
DANGER! If your child tries to open the vehicle belt buckle 18 , stop
immediately as soon as possible. Check whether the child safety seat is
correctly fastened and ensure that your child is correctly secured. Explain
to your child the dangers associated with his actions.
UNFASTENING YOUR CHILD AND REMOVAL:
To unfasten your child or to remove the child safety seat, observe the
steps in Section 6 „REMOVAL“ [PAGE I]
18
1.Let your child sit in the child safety seat and place
the XP-PAD 11 over the chest area of your child.
If you find that the retraction force of the 3-point seat
belt is not enough to ensure that the seat belt is tight
(against the child), the child seat can be used without
XP-PAD 11 ; see Chapter 3 “APPROVAL” [PAGE I].
2.Pull out the vehicle belt and guide it in front of your
child to the vehicle seat buckle 18 .
DANGER! Ensure the vehicle belt is not twisted, as
otherwise the full protective effect of the
retaining system is not ensured.
3.Engage the buckle tongue in the vehicle seat buckle
18 with a CLICK!
4.Place the diagonal seat belt section 16 and lap
belt section 15 on the side of the vehicle seatbelt
buckle 18 into the light red belt guide 05 of the
seat cushion.
DANGER! The vehicle seatbelt buckle 18 must
not be positioned between the light red
belt guide 05 and the armrest.
5.Also place the lap belt section 15 on the other side
of the seat cushion in the light red belt guide 05 .
DANGER! The lap belt section 15 must lie as low
as possible over your child's hips on
both sides.
05
15
16
6.Guide the diagonal seat belt section 16 into the dark
red belt holder 03 of the headrest 22 until it lies
completely in the belt holder 03 and is not twisted.
Tip! If the backrest 14 conceals the belt holder 03 ,
you can adjust the headrest 22 upwards. The diagonal
seat belt section 16 can now be easily inserted. Now
return the headrest 22 to the proper height.
22
03
7.Ensure that the diagonal belt 16 runs over the
collarbone of your child and is not on the neck and
that the key on the belt holder is 03 fully closed.
Tip! You can still adjust the height of the headrest
22 again here in the vehicle.
16
03
16
16
16
11
8.Open the Velcro fastener on the XP-PAD 11 and
fold the top part of the XP-PAD 11 to the side.
9.Insert the diagonal belt 16 in the die nubby surface
of the XP-PAD 11 .
10. Close the XP-PAD 11 again by folding the folded
part back and closing the Velcro fastener.
DANGER! The diagonal seat belt section 16 must
run diagonally backward. You can
adjust the course of the belt with your
vehicle's adjustable belt deflector.
DANGER! The diagonal belt 16 must never be
directed forwards to the belt deflector on
the vehicle. In this case, use the child
safety seat on the back seat only.
11. Tighten the vehicle seat belt by pulling on the diagonal seat belt section 16 .
12. Observe the further steps of the relevant installation type.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising