Buck-Stove-Model-BR1..
MODEL FP-BR-10-ZC
VENT-FREE
WARNING: If information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or loss of life.
−
Do not store or use gasoline or other flammable vapors and liquids in vicinity of this or
any other appliance.
WHAT TO DO IF YOU SMELL GAS
•
•
•
•
−
Do not try to light any appliance.
Do not touch any electrical switch; do not use any phone in your building.
Immediately call your gas supplier from a neighbor’s phone. Follow gas supplier’s instructions.
If you cannot reach your gas supplier, call fire department.
Installation and service must be performed by a qualified installer, service agency or the
gas supplier.
This is an unvented gas-fired heater. It uses air (oxygen) from the room in which it is installed. Provisions for adequate combustion and ventilation air must be provided. Refer to
section “ Producing Adequate Air For Combustion And Ventilation” page 14.
This appliance may be installed in an aftermarket, permanently located, manufactured
(mobile) home, where not prohibited by local codes.
This appliance is only for use with type of gas indicated on rating plate. This appliance is
not convertible for use with other gases.
NOTE: An unvented room heater having an input rating of more than 6,000 Btu per hour shall not be
installed in a bathroom.
WARNING: This appliance is equipped for (natural or propane) gas. Field conversion is not
permitted.
INSTALLER: Leave this manual with appliance.
CONSUMER: Retain this manual for future reference.
MANUFACTURED BY NEW BUCK CORPORATION
200 ETHAN ALLEN DRIVE,
SPRUCE PINE, N.C. 28777
www.buckstove.com
Revised March 2012
TABLE OF CONTENTS
Safety Information and Warnings ................................................................................................. 3
Installation..................................................................................................................................... 6
Fireplace and Framing Dimensions .............................................................................................. 7
Fireplace Clearances ..................................................................................................................... 8
Finishing Your Fireplace .............................................................................................................. 9
Mantel Profiles For Zero Clearance ............................................................................................ 10
Mantel Installation ..................................................................................................................... 11
Mobile Home Installation ........................................................................................................... 13
Gas Connection ........................................................................................................................... 13
Producing Adequate Air for Combustion and Ventilation ........................................................ 14
Air For Combustion And Ventilation Air Iinside Building ........................................................ 16
Air For Combustion And Ventilation Air Outdoors ................................................................... 17
Gas Pressure Check..................................................................................................................... 18
Placement of Logs....................................................................................................................... 19
Lighting Instructions ................................................................................................................... 20
Flame Check ............................................................................................................................... 24
Wiring Diagrams ......................................................................................................................... 25
Important Safeguards .................................................................................................................. 27
Trouble Shooting ........................................................................................................................ 28
Service/Replacement Parts.......................................................................................................... 32
Warranty ..................................................................................................................................... 35
SAFETY INFORMATION WARNINGS
IMPORTANT: READ THIS OWNER’S MANUAL CAREFULLY AND COMPLETELY
BEFORE TRYING TO ASSEMBLE, OPERATE, OR SERVICE THIS APPLIANCE.
IMPROPER USE OF THESE LOGS CAN CAUSE SERIOUS INJURY OR DEATH FROM
BURNS, FIRE, EXPLOSION AND CARBON MONOXIDE POISONING.
•
NOTE: When burning any unit or appliance that combusts fuel for heat, such as
coal, oil, wood or natural and (L.P.) liquid petroleum gas. We highly recommend
the use of smoke and carbon monoxide detectors in your home.
Early signs of carbon monoxide poisoning resemble flu, with headaches, dizziness and/or nausea. If you
have these signs, heater may not be working properly. Get fresh air at once! Have burner serviced.
Some people-pregnant women, persons with heart or lung disease, anemia, those under influence of
alcohol, those at high altitudes-are more affected by carbon monoxide than others.
Make certain you understand and read all Warnings. Keep this manual for reference. It is your guide to
safe and proper operation of this heater and logs.
CAUTION:
Strong drafts, such as a ceiling fan placed directly in front of heater
(pulling from either direction) may create sooting. Sooting will discolor
walls.
1. The installation must conform with local codes, or in absence of local codes, with National Fuel
Gas Code, ANSI Z223.1/NFPA54.
2. This appliance may be installed in an After-Market* Manufactured (Mobile) Home, where not
prohibited by state or local codes.
*
(After-Market: Completion of sale, not for purpose of resale from manufacturer.)
This appliance is only for use with type of gas indicated on rating plate. This appliance is not
convertible for use with other gases.
NOTE: See Page 14, for “Producing Adequate Air For Combustion And Ventilation”.
IMPORTANT:
VENT-FREE HEATERS ADD MOISTURE TO AIR. ALTHOUGH THIS IS
BENEFICIAL, INSTALLING HEATER IN ROOMS WITHOUT ADEQUATE VENTILATION
MAY CAUSE MILDEW TO FORM FROM TOO MUCH MOISTURE.
3. Never install this heater:
- in a recreational vehicle, bathroom.
- where curtains, furniture, clothing, or other flammable objects are less than 42" from
front of heater
-in high traffic areas
- in windy areas
4. Two models are available. One specific model for propane(LP), and one for natural gas. Use
correct type gas for your home. Do not convert from one gas type to another.
NOTE: This appliance complies with ANSI Z21.11.2b-2010 Unvented Room Heater.
Page 3
5. If this heater is used with propane gas, do not place propane supply tank (s) inside any structure.
6.
What To Do IF You Smell Gas:
Shut off gas supply.
- Do not try to light any appliance.
- Do not touch any electrical switch; do not use any phone in your building.
- Immediately call your gas supplier from a neighbor’s phone.
Follow gas supplier’s instructions.
- If you cannot reach your gas supplier, call fire department.
7. When operated for first time, the logs may emit a “paper burning” smell. This smell will gradually
diminish and will be totally eliminated after first few hours of operation. Do not use blower at this
time.
8. “This heater shall not be installed in unusually tight construction unless provisions are
provided for adequate combustion and ventilation air.” See “Producing Adequate Air For
Combustion And Ventilation”, page 14.
9. Surface of gas logs becomes very hot when operating. Keep children and adults away from hot
surface. Gas logs will remain hot for sometime after shutdown. Allow surface to cool before
touching.
10. Do not place clothing or other flammable material on or near appliance.
11. If equipped, fresh air damper must be closed.
12. Keep appliance area clean and free from combustible materials, gasoline and other flammable
flammable vapors and liquids. .
13. If burner shuts off, do not relight until you provide fresh outside air. If burner continues to shut off,
have unit serviced.
14. Do not use this heater if any part has been under water. Immediately call qualified service
technician to inspect room heater and to replace any part of control system and any gas
control which has been under water.
15. Turn off heater and let cool before servicing.
16. These logs are made of bonded fiber. When removing logs and base, do not damage bonded
material. If the material is damaged extensively, loose fiber dust could be emitted into air.
17. Any safety screen or guard removed for servicing an appliance must be replaced prior to
operating heater.
18. This appliance is intended for supplemental heating.
19. “WARNING: Any change to this heater or its controls can be dangerous.”
20. Installation and repairs should be performed by a qualified service person. The appliance
should be inspected before use and at least annually by a professional service person. More
frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc.
It is imperative that control compartments, burners and circulating air passageways of
appliance be kept clean.
Page 4
21. All heater screens must be kept clean when operating gas logs.
22. .”WARNING: Failure to keep the primary air openings of burner clean may result in soot
and property damage.”
24. Do not use this heater for burning trash or cooking. Never place matches, paper, garbage or any
other material on top of logs or into flames.
24. Do not install or operate this heater in areas where impurities in air exist (such as tobacco
smoke or heavy cooking grease). Particles from impurities may discolor walls.
25. Due to high temperatures, appliance should be located out of traffic and away from furniture
and draperies.
26. Children and adults should be alerted to hazards of high surface temperature and should stay
away to avoid burns or clothing ignition.
27. Young children should be carefully supervised when they are in same room with appliance.
28. An unvented room heater having an input rating of more than 6,000 Btu per hour shall not be
installed in a bathroom.
29. The appliance and its appliance main gas valve must be disconnected from the gas supply
piping system during any pressure testing of that system at test pressure in excess of 1/2 psi
(3.5 kPa).
30. The appliance must be isolated from the gas supply piping system by closing its equipment
shut-off valve during any pressure testing of gas supply piping system at test pressures equal
to or less than 1/2 psi (3.5 kPa).
31. “WARNING: Do not allow fans to blow directly into fireplace. Avoid any drafts that alter
burner flame patterns.”
32. “WARNING: Do not use a blower insert, heat exchanger insert or other accessory not
approved for use with this heater.”
Page 5
INSTALLATION
The Model FP-BR10-ZC Vent-Free gas fireplace may be installed in any
room in a Residential home or an After-Market* Manufactured Home.
(Exception: This appliance may not be installed in a bathroom.)
* (After Market: Completion of sale, not for the purpose of resale from manufacturer).
For After-Market Manufactured Home installation, check with state and local codes.
This appliance is only for use with type of gas indicated on rating plate. This appliance is not
convertible for use with other gases.
NOTE: See page 14 for “Producing Adequate Air For Combustion And Ventilation”.
CHOOSING THE LOCATION FOR YOUR FIREPLACE:
Figure 1 shows some of many ways your fireplace may be installed. Consider traffic pattern in your
room and location of doors and windows. Moving air from ceiling fans, open doors and hot air grills
may cause the flames to soot. If a disturbance is found that affects the flames, it must be eliminated by
turning off ceiling fan, closing the door or closing or moving th hot air register. A corner location may
be best where space is limited.
Your fireplace weighs no more than some of your fine furniture. If fireplace is located near a load
bearing wall, additional supports to foundation will not be necessary. HEAVY FACINGS, SUCH AS
BRICK, STONE, ETC., MAY REQUIRE ADDITIONAL FOUNDATION SUPPORT.
NOTE: If this appliance is installed directly on carpeting, tile or other combustible material, other
than wood flooring, appliance shall be installed on a metal or wood panel extending full width
and depth of appliance.
FIGURE 1
GAS LINES
The gas supply line and electrical supply must
be installed before framing in fireplace by a
licensed installer.
DRAFTS
Do not locate fireplace in high traffic areas or
areas exposed to high drafts and winds.
Locate fireplace away from furniture and
draperies.
Page 6
Fireplace and Framing Dimensions (ins.)
25 1/8”
24”
11 5/8”
20 3/8”
26 1/8”
26 1/8”
GAS
LINE
1 3/4”
8”
25 1/8”
13 1/2”
FIGURE 2
WARNING:Installation and repairs should be performed by a qualified service person. The
appliance should be inspected before use and at least annually by a professional service person.
More frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc. It is imperative that control compartments, burners and circulating air passageways of
appliance be kept clean.
Page 7
FIREPLACE CLEARANCES
depth. Alternatively, carpeting, (vinyl) tile, etc. may be
removed beneath fireplace before installing.
COMBUSTIBLE MATERIALS MUST NOT BE
INSTALLED OVER OR TOUCH ANY BLACK
PAINTED SURFACE. DO NOT BLOCK HEAT
CIRCULATING AIR OUTLETS. DOING SO MAY
RESULT IN POTENTIAL FIRE HAZARDS.
1. Sidewall Clearances: Clearances from side of fireplace
opening to any adjacent combustible wall should not be
less than 7".
2. Ceiling Clearances: The ceiling height should
not be less than 42" from top of fireplace opening.
The fireplace may be placed directly on a combustible floor, against
a combustible wall at marked clear-ances or on a raised wooden
platform.
If the fireplace is to be installed on a raised wooden platform,
platform must be a continuous level surface. The fireplace must be
secured in place so it cannot shift positions. The nailing flanges on
the sides of firebox make securing it to framing easy. They were
designed to allow installation of 1/2" wallboard or plywood flush
with face of fireplace.
Only header (see Figure 2) may rest on stand-offs on top of firebox.
When firebox is installed over carpeting, (vinyl) tile or any
combustible material other than wood flooring, it must be
installed on a metal or wood panel extending its full width and
17-3/4"
INSTALLING THE FIREBOX
Figure 3
This list of specific instructions will help you make certain that
every installation operation is performed correctly. Complete
installation steps in sequence shown. STATE AND LOCAL
BUILDING CODES SHOULD BE CONSULTED IN ALL
CASES AS TO
PARTICULAR REQUIREMENTS
CONCERNING INSTALLATION OF A FACTORY BUILT
FIREPLACES. Select location for fireplace by taking into
consideration factors previously outlined in “Choosing the
Location.” See page 5.
Framing the Firebox
The width of framed opening must be 26 1/8". The height of
framed opening must be 25 1/8". The entire fireplace can be
elevated above floor to achieve a raised hearth effect. This can be
done by adding a small platform to achieve desired height.
NOTE: The wiring for lower blower must be installed during
framing stage. The nailing flanges on both sides were designed to
allow installation of 1/2" wallboard or plywood flush with face of
fireplace.
When framing is inside, outside wall will be insulated. If framing
or chase is outside, thin insulation should be used in framing on
back, sides and top. The bottom should be insulated with a hard
insulating board. This will prevent cold from going into chase
through fireplace to living space.
Install Firebox
Install firebox into framed opening by placing it directly in front
of opening and sliding it into proper position.
Level Firebox
Check level of firebox on top edge of fireplace face. Shim if
necessary.
Secure Firebox
Secure fireplace to framing. The nailing flanges on firebox will
make securing firebox to frame quick and easy. Use appropriate
size nails or screws to secure firebox.
Page 8
1/2"
TOP
VIEW
13-1/2"
7" *
26-1/8"
* Note: Minimum 1/2" clearance
NOT required at this point
SIDE
VIEW
13-1/2"
25-1/8"
FRAMING
FRONT
VIEW
HEADER
25-1/8"
26-1/8"
FINISHING YOUR FIREPLACE
There is a wide variety of finishing material available
for your fireplace from formal wall treatments with
marble and mantels, to rustic wood paneling, stone or
brick. Non-Combustible materials used in this
installation such as slate, tile, marble, etc. must be at
least 1/2" thick.
IT IS IMPORTANT THAT THE BLACK FACE OF
FIREPLACE NOT BE COVERED WITH ANY
TYPE OF COMBUSTIBLE MATERIAL.
Non-combustible facing materials such as marble, brick
or ceramic tile may overlap black face of fireplace up to
opening on either side of fireplace. Seal all joints
between black fireplace face and wall covering with a
heat-resistant material such as rock wool insulation or
mortar. Be sure to use high temperature adhesive or
mortar when anchoring brick, stone or tile to face of
fireplace.
Check to see whether man-made brick and stone are
made of non combustible materials before using them
on face of fireplace. Some of these products contain
combustible materials. Combustible wall coverings
such as paneling or wallboard may not overlap black
face of fireplace. The space between wall covering and
fireplace should be sealed with a heat resistant material
such as rock wool insulation or mortar.
NOTE: An “L” shaped steel lintel must be installed
across top of firebox opening where facing materials
such as brick or stone is used on face of firebox. It acts
as a support/firestop. It should be attached to face of
fireplace with screws and sealed to fireplace with a heat
-resistant sealer.
CLEARANCES
3. Mantel Clearances: We have provided 4 different
situations to position your mantel. See Figure 5.
4. Floor Clearances: No clearance is required if
appliance is installed per these instructions.
5. Front Clearances: From Front of fireplace to any
combustible materials should not be any less than
24”.
To ensure a safe installation, the following must be
carefully observed.
1. Sidewall Clearances: Clearances from right or left
side of fireplace opening to any adjacent combustible
wall should not be less than 7", facing unit.
2. Ceiling Clearances: The ceiling height should not
be less than 42" from top of fireplace opening.
NOTE: Adequate clearance around air openings
must be maintained. Never cover any openings on
appliance with any type material.
FIGURE 4
7" MIN.
CLEARANCE
FROM FIREPLACE
OPENING TO SIDE WALL
SIDE WALL
LEFT SIDE
RIGHT SIDE
24” CLEARANCE TO FRONT
Page 9
42" MIN.
CLEARANCE
TO CEILING
MANTEL PROFILES FOR ZERO CLEARANCE CABINET
MUST BE FOLLOWED
MANTELS WITH 3/4" BASE
CEILING
12"
3-1/2"
COMBUSTIBLE
MATERIAL
10"
COMBUSTIBLE
MATERIAL
42"
3-1/2"
3/4"
3"
3/4"
3"
2-1/2"
STAND OFF
STAND OFF
FP-BR10-ZC
FP-BR10-ZC
LOUVERS
2"
LOUVERS
2"
HOOD
HOOD
Bottom of 3/4" Base or Support
must be at least 2-1/2" from top
of Unit if mantel is 10" wide or more.
Bottom of 3/4" Base or Support
must be Flush with top of Unit
if mantel is 10" wide or less.
MANTELS WITH 2-1/2" BASE
SUPPORT
12"
COMBUSTIBLE
MATERIAL
COMBUSTIBLE
MATERIAL
12"
6"
3"
SUPPORT
2-1/2"
3"
2-1/2"
2-1/2"
STAND OFF
FP-BR10-ZC
2"
STAND OFF
LOUVERS
2"
HOOD
FP-BR10-ZC
LOUVERS
HOOD
Bottom of 2-1/2" Base or
Support must be at least
2-1/2" from top of Unit if
mantel is 12" wide or more.
Bottom of 2-1/2" Base or Support
must be Flush with top of Unit
if mantel is 12" wide or less.
Page 10
INSTALLATION OF MODEL FP - BR10- ZC
WITH OPTIONAL WOODEN MANTEL
(1) When choosing right location for your heater and mantel keep following in mind:
NOTE: Due to high temperatures, this heater should be located out of traffic and away
from furniture and draperies.
NOTE: Kit No. (PA KDMH10) Deluxe Wooden Mantel for FP-BR10-ZC.
Kit No. (PA KDM10) Standard Wooden Mantel for FP-BR10-ZC
CAUTION: THE INSTALLATION MUST CONFORM WITH LOCAL CODES OR IN
ABSENCE OF LOCAL CODES, WITH NATIONAL FUEL GAS CODES, ANSI Z223.1/
NFPA 54.
NOTE: See page 18 for “Gas Pressure Check”.
WARNING: YOUNG CHILDREN SHOULD BE CAREFULLY SUPERVISED WHEN
THEY ARE IN SAME ROOM WITH THE APPLIANCE. DO NOT PLACE
CLOTHING OR OTHER FLAMMABLE MATERIAL ON OR NEAR APPLIANCE
(2) Screen(s) can not be removed or altered (Position screen in the closed position before
leaving heater unattended).
(3) Follow instructions for assembly of (Optional) Wooden Mantel. See instructions supplied
with mantel.
(4) After mantel has been assembled, slide heater from rear into opening of mantel.
NOTE: Place a cloth or blanket over front portions of mantel as not to scar wood.
(5) Center heater in opening of mantel. See Figure 6.
(6) Fasten mantel to hearth by using ½" wood screws.
(7) Insert nine (9) ½" wood screws provided with mantel through slots on nailing flange and
secure in place. See Figure 6.
(8) Position mantel and fireplace into desired location.
(9) To light heater, see “Lighting Instructions” pages 19 through 30. Make sure you have right
gas valve for Natural or LP gas.
NOTE: Hook gas supply line into heater. Check for leaks using soap and water, not an open
flame.
NOTE: When used as a bedroom fireplace, unit must be attached to the wall. Use angle
provided with mantel. Also safety screen must be kept mechanically secured to unit as it
is when it leaves manufacturer.
Page 11
TOP MANTEL
1/2" WOOD
SCREWS (9)
REAR
OF
HEATER
MANTEL BASE
FIGURE 6
Page 12
INSTALLATION
AFTER-MARKET MOBILE HOMES
THIS APPLIANCE MAY BE INSTALLED IN AN AFTERMARKET*, PERMANENTLY
LOCATED, MANUFACTURED (MOBILE) HOME, WHERE NOT PROHIBITED BY
LOCAL CODES. *After Market: Completion of sale, not for purpose of resale from manufacturer.
THIS APPLIANCE IS ONLY FOR USE WITH TYPE OF GAS INDICATED ON RATING
PLATE. THIS APPLIANCE IS NOT CONVERTIBLE FOR USE WITH OTHER GASES.
NOTE: For mobile home installation follow “Installation”, pages 6-19.
WARNING: Installation and repairs should be performed by a qualified service person. The
appliance should be inspected before use and at least annually by a professional service person.
More frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc. It is imperative that control compartments, burners and circulating air passageways of
appliance be kept clean.
GAS CONNECTION
CHECK GAS TYPE: Use only type of gas indicated on valve rating plate. If type of gas listed on
the plate is not your type of gas supply, DO NOT INSTALL . Contact your dealer for proper model.
Always use an external regulator for all LP heaters to reduce supply tank pressure to a maximum of
13” W.C. This in addition to regulator furnished with heater.
WARNING: Connection directly to an unregulated LP tank can cause an explosion.
The normal gas connection is 3/8” N.P.T. made at right rear side of appliance.
NOTE: The connecting pipe must be internally tinned copper tubing for use with natural gas. Test
for leaks using a solution of soap and water after completing connection. DO NOT USE OPEN
FLAME.
INSTALLATION SUPPLIES
Before installing heater, gather following materials:
- external regulator
(supplied by installer for propane)
- piping (check local codes)
- manual shutoff valve*
- test gauge connection*
-
ground joint union
sediment trap
tee joint
pipe wrench
sealant (resistant to LP gas)
WARNING:
ANY CHANGE TO THIS HEATER OR ITS CONTROLS CAN BE DANGEROUS.
Page 13
PRODUCING ADEQUATE AIR FOR
COMBUSTION AND VENTILATION
This section is for residential or manufactured (mobile) installation
“This heater shall not be installed in unusually tight construction or unconfined space unless
provisions are adequate for combustion and ventilation air.”
NOTE: This heater shall not be installed in a room or space unless required volume of indoor
combustion air is provided by method in National Fuel Gas Code, ANSIZ223.1/NFPA 54, International Fuel Gas Code or applicable codes.
The National Fuel Gas Code, ANSI Z223.1/NFPA 54 defines unusually tight construction or
unconfined space as a space whose volume is less than 50 cubic feet per 1,000 BTU per hour
(4.8m 3 per kw) of aggregate input rating of all appliances installed in that space and an
unconfined space as a space whose volume is not less than 50 cubic feet per 1,000 BTU per
hour (4.8m 3 per kw) of aggregate input rating of all appliances installed in that space. Rooms
communicating directly with space in which appliances are installed, through openings not
furnished with doors, are considered a part of unconfined space.
“WARNING: IF AREA IN WHICH HEATER MAY BE OPERATED DOES NOT
MEET REQUIRED VOLUME FOR INDOOR COMBUSTION AIR, COMBUSTION
AND VENTILATION AIR SHALL BE PROVIDED BY ONE OF METHODS DESCRIBED IN NATIONAL FUEL GAS CODE, ANSI Z223.1/NFPA 54, INTERNATIONAL
FUEL GAS CODE, OR APPLICABLE CODES.”
“WARNING: IF AREA IN WHICH HEATER MAY BE OPERATED IS SMALLER
THAN THAT DEFINED AS AN UNCONFINED SPACE OR IF BUILDING IS OF
UNUSUALLY TIGHT CONSTRUCTION, PROVIDE ADEQUATE AIR FOR
COMBUSTION AND VENTILATION BY ONE OF METHODS DESCRIBED IN
NATIONAL FUEL GAS CODE, ANSI Z223.1/NFPA 54 AIR FOR COMBUSTION AND
VENTILATION, OR APPLICABLE LOCAL CODES.”
Unusually tight construction is defined as construction where:
a) Walls and ceilings exposed to outside atmosphere have a continuous water vapor retarder
with a rating of 1 perm (6 x 10-11 kg per pa-sec-m2) or less with openings gasketed or sealed;
b) Weather stripping has been added on openable windows and doors.
c) Caulking or sealants are applied to areas such as joints around window and door frames,
between sole plates and floors, between wall-ceiling joints, between wall panels, at
penetrations for plumbing, electrical and gas lines and at other openings.
NOTE: SOME AREAS IN THE UNITED STATES HAVE HIGHER REQUIREMENTS
FOR CUBIC FEET PER 1000 BTU/ HOUR INPUT. (EX. CINCINNATI, OHIO CODES
REQUIRE 70 CUBIC FEET). CHECK YOUR LOCAL CODE BEFORE
INSTALLATION.
Page 14
DETERMINING FRESH-AIR FLOW FOR
HEATER LOCATION
DETERMINE IF YOU HAVE UNUSUALLY TIGHT CONSTRUCTION OR UNCONFINED SPACE
Use this worksheet to determine if you have unusually tight construction or unconfined space.
SPACE: Includes room in which you will install heater plus adjoining rooms with doorless
passageways or ventilation grills between rooms.
1. Determine volume of the space (length x width x height).
Length x Width x Height =_________cu.ft.(volume of space)
EXAMPLE: 20 ft.(Length) x 16 ft.(Width) x 8 ft.(ceiling Height)=
2560 cu. ft. (volume of space)
If additional ventilation to adjoining room is supplied with grills or openings, add volume of
these rooms to total volume of space.
2. Divide the space volume by 50 cubic feet to determine maximum BTU/Hr space can
support.
_________(volume of space)/50 cu. ft. =maximum BTU/Hr space can support)
EXAMPLE: 2560 cu. ft. (volume of space /50 cu. Ft .= 51.2 or
51200 (maximum BTU/Hr space can support)
3. Add BTU/Hr of all fuel burning appliances in space.
Vent-free heater
_______________BTU/Hr
Gas water heater*
_______________BTU/Hr
Gas furnace
_______________BTU/Hr
Vented gas heater
_______________BTU/Hr
Gas fireplace logs
_______________BTU/Hr
Other gas appliances*
+ _______________BTU/Hr
Total
= _______________BTU/Hr
Example: Gas water heater 40000 BTU/Hr
Vent-free heater + 18000 BTU/Hr
Total
= 58000 BTU/Hr
*Does not include direct-vent gas appliances. Direct-vent draws combustion air
from outdoors and vents to outdoors.
4. Compare the maximum BTU/Hr the space can support with actual amount of BTU/Hr
used.
____________BTU/Hr (maximum the space can support)
____________BTU/Hr (actual amount of BTU/Hr used)
Example: 51200 BTU/Hr (maximum the space can support)
58000 BTU/Hr (actual amount of BTU/Hr used)
The space in above example is unusually tight construction because actual BTU/Hr used is
more than maximum BTU/Hr the space can support. You must provide additional fresh
air. Your options are as follows:
Page 15
A. Rework worksheet, adding space of an adjoining room. If extra space provides an unconfined space, remove door to adjoining room or add ventilation grills between rooms. See
“Ventilation Air From Inside Building”, page 21.
B. Vent room directly to outdoors. See “Ventilation Air From Outdoors”, page 22.
C. Install a lower BTU/Hr heater, if lower BTU/Hr size makes room unconfined.
If actual BTU/Hr used is less than maximum BTU/Hr space can support, space is an
unconfined space. You will need no additional fresh air ventilation.
WARNING: YOU MUST PROVIDE ADDITIONAL VENTILATION AIR IN A UNUSUALLY TIGHT CONSTRUCTION.
AIR FOR COMBUSTION
AND VENTILATION FROM INSIDE BUILDING
This fresh air would come from an adjoining unconfined space. When venting to an adjoining space,
you must provide two permanent openings: one within 12" of ceiling and one within 12" of floor on
wall connecting two spaces. (See Options 1 and 2, Figure 7.) You can also remove door into adjoining
room. (See Option 3, Figure 7.)
WARNING
REWORK WORKSHEET, ADDING SPACE OF ADJOINING UNCONFINED SPACE.
COMBINED SPACES MUST ADEQUATE AMOUNT OF AIR TO SUPPLY ALL
APPLIANCES IN BOTH SPACES.
NOTE: Each opening shall have a minimum free area of 1 square inch per 1000 BTU’s per hour of
total input ratings of all gas utilization equipment in confined space, but not less than 100 square inches.
Figure 7 Ventilation Air From Inside Building
Page 16
WARNING
THIS HEATER MUST HAVE ADEQUATE AMOUNT OF AIR FOR PROPER
OPERATION. IF NOT, POOR FUEL COMBUSTION COULD RESULT. READ THE
FOLLOWING INSTRUCTIONS TO ENSURE PROPER AMOUNT OF AIR FOR THIS AND
OTHER FUEL-BURNING APPLIANCES IN YOUR HOME.
AIR FOR COMBUSTION AND
VENTILATION FROM OUTDOORS
Provide extra fresh air by using ventilation grills or ducts. You must provide two permanent
openings: one within 12" of the ceiling and one within 12" of floor. Connect these items
directly to outdoors. These spaces include attics and crawl spaces. Follow National Fuel Gas
Code NFPA 54/ANSI Z223.1, Section 5.3, “Air For Combustion and Ventilation” for required
size of ventilation grills or ducts.
IMPORTANT: Do not provide openings for inlet air into attic if attic has a thermostatcontrolled power vent. Heated air entering attic will activate power unit.
Ventilated Attic
Outlet Air
To Attic
Outlet Air
To Crawl
Space
Inlet Air
Ventilation
To Crawl Space
Inlet Air
Page 17
GAS PRESSURE CHECK
Check inlet pressure to burner to insure that it is as shown in table below.
NOTE: The pressure check point is located on the right side of valve facing burner.
The appliance and its appliance main gas valve must be disconnected from gas supply
piping system during any pressure testing of that system at test pressures in excess of 1/2
psi (3.5kPa).
The appliance must be isolated from gas supply piping system by closing its equipment
shut-off valve during any pressure testing of gas supply piping system at test pressures
equal to or less than 1/2 psi (3.5 kPa).
MODEL
Gas
Maximum Heat Input
Gas Inlet Pressure:
Maximum
Minimum
Manifold Pressure
FP-BR10-ZC
Natural
10000
FP-BR10-ZC
Propane
10000
10.5 ins. W.C.
* 5 ins. W.C.
3.5 ins. W.C.
13 ins. W.C.
*11 ins. W.C.
9 ins. W.C.
NOTE: On initial installation it may be necessary to bleed out air in gas lines. Do this by
holding control knob and turning knob to pilot position for about 30 seconds.
To check Regulator pressure, remove pressure tag plug at the left side of Regulator facing
heater. The pressure should be checked with heater burning and control set on high. After
measuring pressure, replace pressure tap plug, ensuring that there are no leaks.
* For the purpose of minimum input adjustment.
WARNING
This appliance is equipped for (natural or propane) gas.
Field conversion is not permitted.
Page 18
LOG PLACEMENT
Logs are shipped secured in unit.
NOTE: When operated for first time, logs may emit a “paper burning” smell. This smell
will gradually diminish and will be totally eliminated after first few hours of operation.
Do not use blower at this time.
Front View of Logs
WARNING
“FAILURE TO POSITION PARTS IN ACCORDANCE WITH THESE DIAGRAMS OR
FAILURE TO USE ONLY PARTS SPECIFICALLY APPROVED WITH HEATER
MAY RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY.”
WARNING
“DO NOT ALLOW FANS TO BLOW DIRECTLY INTO THE FIREPLACE. AVOID
ANY DRAFTS THAT ALTER BURNER FLAME PATTERN.”
Page 19
OPERATING INSTRUCTIONS
Before operating this appliance, proceed through following checklist
.
1. Read and understand these instructions before operating this appliance.
2. Check that there no leaks. If you smell gas do not attempt to light this appliance.
LIGHTING INSTRUCTIONS
MODULATING VALVE(MAXITROL)
FOR YOUR SAFETY, READ BEFORE LIGHTING
WARNING
IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY
OR LOSS OF LIFE.
A.
This appliance has a pilot which must be lighted by hand. When lighting pilot,
follow these instructions exactly.
B. BEFORE LIGHTING: Smell all around appliance for gas. Be sure to smell next
to floor because gas is heavier than air and will settle on floor.
WHAT TO DO IF YOU SMELL GAS
* Do not try to light any appliance.
* Do not touch any electrical switch; do not use any phone in your building.
* Immediately call your gas supplier from a neighbor’s phone. Follow gas
supplier’s instructions.
* If you cannot reach your gas supplier, call your local fire department.
C. Use only your hand to push in or turn the gas control knob. Never use tools. If knob
will not push in or turn by hand, don’t try to repair it, call a qualified service technician.
Force or attempted repair may result in fire or explosion.
D. Do not use this appliance if any part has been under water. Immediately call a qualified
service technician to inspect the appliance and to replace any part of control system
and any gas control which has been under water.
Page 20
LIGHTING INSTRUCTIONS
1.
2.
3.
4.
5.
6.
STOP! Read safety information on the previous page.
Make sure manual shutoff valve is fully closed.
Open access panel door, located in lower front center of base for access to control knobs.
Turn off all electric power to appliance.
Set thermostat (flame control) to lowest setting.
Push in and turn control knob clockwise
to “OFF” position.
PILOT
ON
4
IGNITE
OFF
MERTIK
6
5
MAXITROL
7
3
2
1
FLAME
CONTROL
CONTROL
KNOB
FIGURE 3
7. “Wait (5) five minutes to clear out any gas. Then smell for gas, including near floor. If
you smell gas, STOP! Follow step “B” in safety information on previous page. If you
don’t smell gas, go to next step.”
8. Find Pilot: follow small metal tub from right hand rear of gas control valve. The pilot is
located behind burner tube and in front of rear log. Fully open manual shut-off valve.
9. Turn control knob counterclockwise
to “PILOT” position. Press in
control knob for (15) fifteen seconds (see figure 3).
10. With control knob pressed in, turn control knob clockwise
to IGNITE and
then immediately back to PILOT with button still pressed in. This will light pilot. If
needed, keep repeating this step until pilot lights.
11. Keep control knob pressed in for one (1) minute after lighting pilot. After (1) minute,
release control knob. If pilot goes out, repeat steps 1 through 9.
• If knob does not pop up when released, stop and immediately call your service technician
or gas supplier.
• “If pilot will not stay lit after several tries, turn gas control knob to “OFF” and call your
service technician or gas supplier.”
12. Turn control knob counterclockwise
to “ON” position.
13. “Set thermostat (flame control) to desired setting. Turn clockwise
for “LOW”
and counterclockwise
for “HIGH”.
Page 21
IGNITER ELECTRODE
THERMO-COUPLE
O.D.S
PILOT BURNER
PILOT
13. Close access panel door.
14. “Turn on all electric power to appliance.”
CAUTION
DO NOT TRY TO ADJUST HEATING LEVELS BY USING
MANUAL SHUTOFF VALVE.
TO TURN OFF GAS TO APPLIANCE
SHUTTING OFF UNIT:
Open access panel door, located in lower front center of base for access to control knobs.
Set thermostat (flame control) to lowest setting.
Turn control knob clockwise
to full “OFF” position.
“Turn off all electrical power to appliance if service is to be performed.”
Close access panel door.
SHUTTING OFF BURNER ONLY (pilot stays lit)
1. Open access panel door, located in lower front center of base for access to control knobs.
2. Turn control knob clockwise
to “PILOT” position.
2. Close access panel door.
1.
2.
2.
3.
4.
CAUTION:
Hot while in operation. Do Not Touch. Keep children, clothing, furniture,
gasoline and other liquids having flammable vapors away.
CAUTION: DO NOT TRY TO ADJUST HEATING LEVELS BY USING MANUAL
SHUTOFF VALVE.
WARNING:
Improper installation, adjustment, alteration, service or maintenance can
cause property damage, personal injury or loss of life. Refer to owner’s information manual
provided with this appliance. Installation and service must be performed by a qualified
installer, service agency or the gas supplier.
IMPORTANT:
Always operate appliance at completely “ON” or completely “OFF”
positions. Never use the heater at a setting between these positions as this can result in
improper combustion and excessive carbon monoxide emissions.
Page 22
THERMOSTAT CONTROL OPERATION
The thermostat control used on this heater differs from standard thermostats. Standard
thermostats simply turn burner on and off. The thermostat used on this heater senses room
temperature and adjusts amount of gas flow to burner. This will increase or decrease
flame height. At times, room may exceed set temperature, which will cause burner to shut
off. When room temperature drops below thermostat setting, burner will cycle itself on
again. The flame control knob can be set to any level between 2 and 7.
NOTE: The thermostat sensing bulb measures temperature of air near heater cabinet.
This may not always agree with room temperature ( depending on housing construction,
installation location , room size, open air temperature, etc.). Frequent use of your heater
will allow you to determine your personal comfort levels.
MANUAL LIGHTING PROCEDURE
1. If the pilot cannot be ignited with igniter on the control valve, it can be manually lit with
use of a paper match and a lighter rod.
2. Place the match in holder and light. With other hand, depress control knob
counterclockwise
to PILOT.
3. Use rod to light match and ignite pilot. The pilot is located behind burner tub and in
front of rear log. Fully open manual shut-off valve.
4. Continue to hold control knob for an additional (1) one minute to ensure pilot
is completely on.
• If knob does not pop up when released, stop and immediately call your service technician or gas supplier.
• “If the pilot will not stay lit after several tries, turn gas control knob to “OFF” and call
your service technician or gas supplier.”
5. Turn control knob counterclockwise
to “ON” position.
“Set thermostat (flame control) to desired setting. Turn clockwise
for “LOW”
and counterclockwise
for “HIGH”.
6. Close the access panel door.
7. “Turn on all electric power to appliance.”
Page 23
FLAME CHECK
A periodic check of flames should be made. The pilot flame should always be present when
gas logs are in operation.
FLAME: Propane (LP) should produce a flame that is 3"-4" above rear log. This flame should
be yellow.
Natural gas should produce a flame that is 3"-4" above rear log. This flame should
be mostly blue except for the top 1/2" which should be yellow.
FLAME
NATURAL
PROPANE
Page 24
WARNING:
CHILDREN AND ADULTS SHOULD BE ALERTED TO
HAZARDS OF HIGH SURFACE TEMPERATURE AND SHOULD STAY AWAY TO
AVOID BURNS OR CLOTHING IGNITION. YOUNG CHILDREN SHOULD BE
CAREFULLY SUPERVISED WHEN THEY ARE IN
SAME ROOM WITH
APPLIANCE.
WARNING:
DO NOT PLACE CLOTHING OR OTHER FLAMMABLE
MATERIALS ON OR NEAR APPLIANCE.
WIRING DIAGRAM
MOTOR
THERMOSTAT
JUMPER
JUMPER
JUMPER
GREEN
WHITE
BLACK
RHEOST
POWER CORD
BLACK
Figure 10
NOTE: “If any of original wire as supplied with appliance must be replaced, it must be
replaced with a wire of at least a 105o C. temperature rating.”
NOTE: Installation and repair should be done by a qualified service person. This heater
should be inspected before use and at least annually by a qualified service person. More
frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc.
It is imperative that control compartments and circulating air passageways of heater be
kept clean.
CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can
cause improper and dangerous operation.
Verify proper operation after servicing.
Page 25
WARNING: ELECTRICAL GROUNDING INSTRUCTION:
THIS APPLIANCE
IS EQUIPPED WITH A THREE-PRONG (GROUNDING) PLUG FOR YOUR
PROTECTION AGAINST SHOCK HAZARD AND SHOULD BE PLUGGED
DIRECTLY INTO A PROPERLY GROUNDED THREE-PRONG RECEPTACLE.
NOTE:
#PESBRO84 Blower Motor
Rating: 120 volts/60HZ/0.54 Amps. 1 P.H
NOTE:
For convenience, allow licensed electrician to install properly grounded
3-plug receptacle near unit.
Page 26
IMPORTANT SAFEGUARDS
Although your gas logs are very realistic in appearance, it is not a real burning fireplace and must not be
used for burning rejected material.
• To avoid irreparable damage to heater or personal injury, matches, paper, garbage or any other
material must not be placed or thrown on top of logs or into flames.
• To avoid personal injury, do not touch hot surfaces when heater is operating.
• Close supervision is necessary when heater is being operated near children.
WARNING:
THE LOGS ARE MANUFACTURED FROM BONDED CERAMIC
FIBER. THIS IS A COMMONLY USED MATERIAL IN INDUSTRY WORLDWIDE.
IN EVENT THAT A LOG SHOULD BE REMOVED, CARE SHOULD BE TAKEN
NOT TO DAMAGE THE BONDED MATERIAL.INTENTIONAL MISUSE OR
DELIBERATELY FRAGMENTING MATERIAL COULD LEAD TO INHALING
FIBERS AND BE HAZARDOUS TO YOUR HEALTH.
THIS HEATER IS INTENDED FOR USE AS A GAS HEATER FIREPLACE AS
DESCRIBED IN THESE INSTRUCTIONS. IT SHOULD NOT BE USED FOR ANY
OTHER PURPOSE.
CLEANING
CAUTION: BEFORE CLEANING OR MOVING THESE LOGS OR OTHER PARTS
OF THE HEATER, BE SURE TO READ ABOVE SECTIONS ON “IMPORTANT
SAFEGUARDS.”
The appliance must be turned “OFF” before cleaning inside firebox (burn area),
make sure pilot is “OFF” completely and appliance has cooled.
• All cleaning should be carried out when heater is cold. Limited cleaning is required with
normal use. Dusting front of base, top of piezo cover or control knob panel may be
required occasionally. Do not use cleaning fluids to clean logs or any other part of heater.
• If flames show unusual shapes or behavior or if burner fails to ignite properly, burner holes
may require cleaning. If this occurs, contact your nearest dealer to service heater.
• The heater can be cleaned by removing logs. Lift the logs gently, as not to damage fiber
pieces. The logs have been spot glued in place for shipping, use caution when removing.
Lift each log by holding it carefully at each end. Use a vacuum cleaner to remove dust and
loose particles from base, logs and around burner and ODS/Pilot. Gloves are
recommended to prevent fibers from breaking skin. If skin is broken, clean with soap and
water.
WARNING: Failure to keep the primary air openings of the burner clean may result in
soot and property damage.
Page 27
TROUBLESHOOTING
WARNING
TURN OFF BURNER, UNPLUG HEATER AND LET COOL BEFORE
SERVICING. ONLY A QUALIFIED SERVICE PERSON SHOULD
SERVICE AND REPAIR HEATER.
CAUTION
NEVER USE A WIRE, NEEDLE, OR SIMILAR OBJECT TO CLEAN
ODS/PILOT. THIS CAN DAMAGE ODS/PILOT.
OBSERVED
PROBLEM
POSSIBLE
CAUSE
1. Igniter button is pressed,
no spark at ODS/Pilot
1. I g n i t e r
electrode
positioned incorrectly.
2. Igniter electrode broken
3. Igniter electrode not connected to igniter cable
4. Igniter cable pinched or
wet
5. Piezo igniter nut is loose
6. Broken igniter cable
7. Bad piezo igniter
2. Igniter button is pressed
Spark at ODS/Pilot
No Ignition
1. Gas supply turned off or
manual shutoff valve is
closed
2. Control knob not in
“PILOT” position
3. Control knob not pressed
in while in “PILOT”
position
4. Air in gas lines when
installed
Page 28
SOLUTION
1. Replace igniter
2. Replace igniter
3. Reconnect igniter cable
4. Free igniter cable if
pinched by any metal or
tubing. Keep igniter
cable dry
5. Tighten nut holding
piezo igniter to heater
cabinet. Nut is located
inside heater cabinet at
top
6. Replace igniter cable
7. Replace piezo igniter
1. Turn on gas supply or
open manual shutoff
valve
2. Turn control knob to
“PILOT” position
3. Press in control knob
while in “PILOT”
position
4. Continue to hold down
control knob. Repeat
igniting operation until
air is removed.
5. Contact local propane
gas company
6. Clean ODS/Pilot or
6. ODS/Pilot is clogged
replace ODS/Pilot
assembly
7.
Replace gas regulator
7. Gas regulator setting is not
correct
5. Depleted gas supply
3. ODS/Pilot lights but
flame goes out when
control knob is released
1. Control knob is not fully 1. Press control knob
completely
pressed in
2. Control knob not pressed 2. After ODS/Pilot lights
keep control knob
in long enough
pressed 30 seconds
3. Safety interlock system 3. Wait 1 (one) minute for
safety interlock system
has been triggered (if
to reset
equipped)
4.
Fully open manual
4. Manual shutoff valve not
shutoff valve
fully open
5. Thermo-couple connection 5. Hand tighten until snug,
then tighten 1/4 turn
loose at control valve
6. Pilot flame not touching 6. Contact local propane
gas company. Clean
thermo-couple, which
ODS/Pilot (See
allows thermo-couple to
“Cleaning and
cool causing pilot flame to
Maintenance”), or
go out. This problem can
replace ODS/Pilot
be caused by one or both
assembly
of the following:
A) low gas pressure
B) dirty or partially
clogged ODS/Pilot
7. Replace valve control
7. Control valve damaged
4. Burner does not light after
ODS/Pilot is lit
1. Burner orifice is clogged
5. Delayed ignition of burner
1. Manifold pressure is too 1. Contact local propane
gas company
low
2. Clean burner (“See
2. Burner orifice is clogged
Cleaning and
Maintenance”) or
replace burner orifice
1. Clean burner (See
“Cleaning and
Maintenance”) or
2. Inlet gas pressure is too
replace burner orifice
low
2. Contact local propane
gas company
Page 29
6. Burner backfiring during
combustion
1. Burner orifice is clogged
or damaged
2. Burner damaged
3. Gas regulator defective
1. Clean burner (See “Cleaning and Maintenance “) or
replace burner orifice
2. Replace Burner
3. Replace gas regulator
7. Slight smoke or odor
during initial operation
1. Residues from
manufacturing process
1. Problem will stop after a
few hours of operation
8. Heater produces a whistling noise when burner is
lit
1. Turning control knob to
“HI” position when
burner is cold (if
equipped with this type
of valve)
2. Air in gas line
1. Turn control knob to
“LOW” position and allow
to warm
3. Air passageways on
heater blocked
4. Dirty or partially
clogged burner orifice
Page 30
2. Operate burner until air is
removed from line. Call
local propane company to
check gas line.
3. Observe minimum
installation clearances
4. Clean burner or replace
orifice
WARNING
IF YOU SMELL GAS:
* SHUT OFF GAS SUPPLY
* DO NOT TRY TO LIGHT APPLIANCE
* DO NOT TOUCH ANY ELECTRICAL SWITCH; DO NOT USE ANY
PHONE IN YOUR BUILDING
* IMMEDIATELY CALL YOUR GAS SUPPLIER FROM A NEIGHBOR’S
PHONE. FOLLOW GAS SUPPLIER’S INSTRUCTIONS.
* IF YOU CANNOT REACH YOUR GAS SUPPLIER, CALL FIRE
DEPARTMENT.
IMPORTANT: Operating heater where impurities in air exist may create odors. Cleaning
supplies, paint, paint remover, cigarette smoke, cements, glues, new carpet or textiles, etc. create
fumes. These fumes may mix with combustion air and create odors.
9. Heater produces a
clinking/ticking noise
just after burner is lit or
shut off
1. Metal expands while
heating or contracts
while cooling.
1. This is common with most
heaters. If noise is
excessive, contact a
qualified service person.
10. Heater produces
unwanted odors
1. Heater burning vapors
from paint, hairspray,
glues, etc. (See
Important above)
2. Low fuel supply
3. Gas leak (See
WARNING above)
1. Ventilate room. Stop using
odor causing products
while heater is running.
11. Heater shuts off in use
(ODS operates)
1. Not enough fresh air is
available.
2. Low line pressure
3. ODS/Pilot is partially
clogged
12. Gas odor even when
control knob is in “OFF”
position
1. Gas leak (See
WARNING above)
2. Control valve defect
13. Gas odor during
combustion
1. Foreign matter between
control valve and burner
2. Gas leak (See
WARNING above)
Page 31
2. Refill supply tank.
3. Locate and control all
leaks. See “Checking Gas
Connections”.
1. Open window/door for
ventilation
2. Contact local propane co.
3. Clean ODS/Pilot
1. Locate and correct all
leaks (See “Checking Gas
Connections”)
2. Replace control valve
1. Remove foreign matter
from gas tubing
2. Locate and correct all
leaks “See “Checking Gas
Connections”)
SERVICING
Repair and replacement work should only be performed by a qualified service technician.
Always shut off the gas supply and make sure heater is cool before beginning any service
operation. Check for gas leaks after servicing.
REPAIR PARTS
A parts list with exploded view follows. Always include correct name, part number and model
number of heater when ordering service parts. Please contact your local dealer or Distributor
when ordering or if one is not available, you may contact:
New Buck Corporation
P.O. Box 69
Spruce Pine, NC 28777
(828)-765-6144
Page 32
PARTS LIST
Maxitrol Valve
KEY #
PART #
DESCRIPTION
1
GV 30B5A2L7B
Maxitrol LP Valve
1
1A
GV 30B5A2N7B
Maxitrol Nat. Valve
1
2
PE 4966
3/8" - 3/8" Elbow
1
3
PS 112736
Maxitrol Regulator Holder
1
4
PS 1024
BR 10 Burner Base
1
5
PO BR10 Burn
Single Burner
1
6
PE TPT100/433
Thermo-couple/ (Copreci)
1
7
7A
PE 21500053
PE 2150054
Copreci ODS Nat. Pilot
Copreci ODS LP Pilot
1
1
8
8A
PE RV12LF30
PE RV12LF90
Maxitrol Regulator-Nat.
Maxitrol Regulator-LP
1
1
9
RF 14ALMTUB
1/4" Aluminum Tubing
1
10
PH 1166
3/8" Street Elbow
1
11
PE 6482
1/4" -1/8" Compression Adapter
2
12
PO Orifice
Orifice Nat. or LP
1
13
PS 112726
M1127 Burner Supports
2
14
PO 38634ALMTUB
3/8" x 6 - 3/4" Burner Tube
1
15
PO 54ORFHLD
Angled Orifice Holder
1
16
PESBRO84
Blower Motor
1
Page 33
QUANTITY
BLOWN UP VIEW OF BURNER ASSEMBLY
*16 Not shown on this page. See page 25, figure 10 for wiring diagram.
Page 34
NEW BUCK CORPORATION
We reserve right to amend these specifications at any time without notice. The only warranty
applicable is our standard written warranty. We offer no other warranty, expressed or implied.
LIMITED WARRANTY
MODEL FP-BR10-ZC
New Buck warrants this product to be free from defects in materials and components for two
(2) years from date of first purchase, provided that product has been properly installed,
operated and maintained in accordance with all applicable instructions. To make a claim under
this warranty Bill of Sale or canceled check must be presented.
This warranty is extended only to original retail purchaser and covers cost of parts required to
restore heater to proper condition. Warranty parts MUST be obtained through an authorized
Buck Stove dealer and/or New Buck, who will provide original factory replacement parts.
Failure to use original factory replacement parts voids this warranty. The heater must be
installed by a qualified installer in accordance with all local codes and instructions furnished
with unit.
Warranty does not apply to parts that are not in original condition, normal wear and tear or
parts that fail or become damaged as a result of misuse, accidents, lack of proper maintenance
or defects caused by improper installation.
WARRANTY DOES NOT COVER:
-
Removal and re-installation cost
Labor costs for replacements or repairs
Transportation
Cost of service call to diagnose trouble
Painted surfaces
Damage or defect caused by improper installation, accident, misuse, abuse or alteration
TO FULL EXTENT ALLOWED BY LAW OF THE JURISDICTION THAT GOVERNS
SALE OF PRODUCT, THIS EXPRESS WARRANTY EXCLUDES ANY AND ALL
OTHER EXPRESSED WARRANTIES AND LIMITS DURATION OF ANY AND ALL
WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE TO ONE (1) YEAR FROM DATE OF FIRST
PURCHASE. NEW BUCK LIABILITY IS HEREBY LIMITED TO PURCHASE PRICE OF
PRODUCT AND NEW BUCK SHALL NOT BE LIABLE FOR ANY OTHER DAMAGES
WHATSOEVER INCLUDING INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some states do not allow a limitation on how long an implied warranty lasts or an exclusion or
limitation of incidental or consequential damages, so above limitation on implied warranties
or exclusion on damages may not apply to you.
This warranty gives you specific legal rights. Other rights may vary from state to state.
Page 35
OWNER REGISTRATION
The attached owner registration card must be completed in its entirety and mailed within 30
days from date of installation in order for warranty coverage to begin to:
New Buck Corporation
P.O. Box 69
Spruce Pine, NC 28777
PLEASE NOTE: Owner Registration Card must contain Authorized Buck Stove Dealer
Number and Certified Installer’s number (if applicable) for warranty coverage to begin.
NAME: _____________________________________________________
ADDRESS: __________________________________________________
CITY: ______________________________________________________
STATE: ______________________
ZIP: ________________________
MODEL #: FP-BR10ZC SERIAL #: ___________________________
DATE OF INSTALLATION: ___________________________________
INSTALLER’S NAME: ________________________________________
PURCHASED FROM: ________________________________________
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising