Trango StrataLINK 24 Software v1.2.4 Release

Trango StrataLINK 24 Software v1.2.4 Release
Trango StrataLINK 24
Release Notes v1.2.4
Trango StrataLINK 24
Software v1.2.4
Release Notes &
Upgrade Instructions
August 25 , 2014
Trango Systems Confidential and Proprietary Information
Page 1 of 18
© 2011-2013 Trango Systems, Inc. All rights reserved.
Trango StrataLINK 24
Release Notes v1.2.4
Table of Contents
•
•
•
•
•
•
•
•
Image Updates
Supported Modulation/Symbol rate combination
New Features
Bug Fixes
Limitations
Upgrade Instructions – FTP
Upgrade Instructions – TFTP
Revision History
Trango Systems Confidential and Proprietary Information
Page 2 of 18
© 2011-2013 Trango Systems, Inc. All rights reserved.
Trango StrataLINK 24
Release Notes v1.2.4
Trango StrataLINK 24 v1.2.4 Release
For Model SL-24 and SL-24-X ONLY – DO NOT load into SL-24-E or SL-24-EX models
The release consists of the following software images
FPGA version:
OS version
FW version
Modem Version
0118040E
2p6r22b0D082514
1p2r4D082514
6201.4.4
Bold typeface indicates new images for this release.
Supported Modulation/Symbol rate combination in this release – Compression ON
Full Duplex Capacity (Mbps) - 1518/72 byte IPV4 packets UDP + VLAN Tag
Channel
Width/Sym
rate (MHz)
QPSK
10/7.5
14/12.2
20/16
25/20.8
15/20
22/34
31/48
39/61
30/26
QAM
QAM
QAM
QAM
QAM
16
32
64
128
256
23/33
34/53
47/73
60/90
30/44
45/70
63/96
80/126
37/57
55/84
78/120
99/150
46/72
67/102
96/150
120/186
53/84
78/120
111/173
140/216
47/73
71/108
95/144
118/186
142/222
40/34.8
63/96
96/150
128/198
159/246
50/42
78/120
95/144
118/180
141/222
157/246
189/294
195/305
234/366
60/52
8PSK
QAM
512
QAM
1024
60/90
88/137
126/198
160/251
68/102
100/156
143/222
182/282
NA
113/174
162/251
206/323
167/257
192/300
218/342
247/383
192/300
225/353
256/401
291/456
329/515
238/371
287/450
277/431
333/522
318/497
391/612
361/569
431/678
407/641
487/726
New Features
1. Added new commands to the CLI interface.
a. Link_position <0: local ,1:remote>
b. XPIC HV <0: Horizontal , 1: Vertical>
It can be used to display current radios polarization when XPIC is not enabled.
2. Web interface will display peer unit MAC address
Bugs Fixed
1. Removed “remote management “ feature
2. Syslog timestamp will be the same as NTP system time.
Trango Systems Confidential and Proprietary Information
Page 3 of 18
© 2011-2013 Trango Systems, Inc. All rights reserved.
Trango StrataLINK 24
Release Notes v1.2.4
Notes
1. RF In/Out counters read slightly lower than actual number of packets going over the air.
GE1 and GE2 port counters are always accurate.
2. Port Priority not functional
3. Pause on/off not functional
Trango Systems Confidential and Proprietary Information
Page 4 of 18
© 2011-2013 Trango Systems, Inc. All rights reserved.
Trango StrataLINK 24
Release Notes v1.2.4
Software Image Upgrade Procedure – FTP
(All Versions)
Please review these instructions before starting to ensure that you have adequate time
scheduled to perform the upgrade as well as fully understand the implications of the process.
While all software is tested by Trango Systems on current hardware before being released, it
is strongly suggested that you initially perform this upgrade on your lab equipment and not
initially in a production environment and test for any and all needed functionality before
deploying.
Image upgrade for SL24 will be copied to flash during image upgrade (bootimage upgrade)
and will not affect the working link until the system is rebooted / power cycled.
To perform the firmware upgrade using FTP, use the ftp command to load the images into
memory, then the bootimage upgrade commands. The FTP method is much faster and has
built in error checking than TFTP. If you prefer to use the TFTP method, instructions can be
found in subsequent pages.
All that is needed is the IP address of the ftp server, a username/password, and the filename to
be uploaded. The new file to be uploaded should be placed on the server. The ftp server will
prompt for the password before allowing access.
If the SL-24 is configured with a route to the Internet, you can even pull the new software
images directly from our ftp server. If you would rather load them into a local server, please
change the IP addresses and directory structure in the examples below as needed. You will
need an appropriate default gateway setup in the SL-24 as well as a route to the Internet
through out of band management or IBM.
1. Plan to use the file directly from Trango’s FTP server or copy it to your own local FTP
server. It is recommend to verify the file name and path to ensure that nothing has
changed since this document was prepared.
2. Note down the current version of the firmware loaded in the radio (CLI: <version>).
3. Connect Management Ethernet port to PC.
4. Configure an IP address in unit if not already done.
5. Start a Telnet or SSH session. Log into the SL-24, go to config node, and then debug
node to test connectivity to your ftp server.
(CLI-view)# config
Password: trango
(CLI-config)# debug
Trango Systems Confidential and Proprietary Information
Page 5 of 18
© 2011-2013 Trango Systems, Inc. All rights reserved.
Trango StrataLINK 24
Release Notes v1.2.4
Debug> ping 74.62.177.9
PING 74.62.177.9 (74.62.177.9): 56 data bytes
64 bytes from 74.62.177.9: seq=0 ttl=127 time=0.965 ms
64 bytes from 74.62.177.9: seq=1 ttl=127 time=10.009 ms
Press ctrl+c to stop the ping.
--- 74.62.177.9 ping statistics --2 packets transmitted, 2 packets received, 0% packet loss
round-trip min/avg/max = 0.965/5.487/10.009 ms
If the ping test is not successful, check your IP address and default gateway to ensure
that those are addresses that will reach the Internet through your firewall.
6. After verifying connectivity, return to config node and save your config if not already
saved:
Debug> cli
Trango System: Trango StrataLink 24 Command Line Interface v1.2.3
(CLI-view)# config
Password: trango
(CLI-config)# config save
New configuration saved
SUCCESS
7. Run the ftp command from the command line as follows to open access to the server:
(CLI-config)# ftp 74.62.177.9 giga
password: giga4773
If prompted for the password multiple times, check the connectivity to the server by
pinging the FTP server IP address from the debug prompt. You may also test the ftp
credentials from a laptop or other computer on the same network subnet.
8. Next, get the file from the FTP server by typing the get command from the ftp prompt.
ftp> get TL-StrataLink/SL24_v1.2.4.tar.gz
##########
Get operation successful with passive mode
9. Logout of the ftp session
ftp> logout
10. Process the upgrade using the bootimage upgrade command.
(CLI-config)# bootimage upgrade
................................................................................
................................................................................
.......................................................
SUCCESS
Trango Systems Confidential and Proprietary Information
Page 6 of 18
© 2011-2013 Trango Systems, Inc. All rights reserved.
Trango StrataLINK 24
Release Notes v1.2.4
11. After the process returns success, reboot the radio for the new image to be loaded into
active memory.
(CLI-config)# reboot
12. Check the new version on the system with CLI command “version”. It should match with
the versions listed earlier. In case of mismatch version, please perform the upgrade
again from step 1.
FPGA version:
OS version
FW version
Modem Version
0118040E
2p6r22b0D082514
1p2r4D082514
6201.4.4
Please follow all the instructions as listed above in the upgrade instructions. In the case of
version mismatch on the system (local/remote/system) the system is NOT guaranteed to work.
In the event of a power failure during the upgrade process or any mismatch conflict, please open
a support request at support.trangosys.com for further assistance. Serial console remote access
to the OMUs might be required in the event of such failure. It is suggested that all customers
have at least one serial/console cable available at each site.
Please don't make any implicit assumptions.
In case of any doubt please contact technical support for clarification.
Trango Systems Confidential and Proprietary Information
Page 7 of 18
© 2011-2013 Trango Systems, Inc. All rights reserved.
Trango StrataLINK 24
Release Notes v1.2.4
Software Image Upgrade Procedure - TFTP
(All Versions)
Please review these instructions before starting to ensure that you have adequate time
scheduled to perform the upgrade as well as fully understand the implications of the process.
While all software is tested by Trango Systems on current hardware before being released, it
is strongly suggested that you initially perform this upgrade on your lab equipment and not
initially in a production environment and test for any and all needed functionality before
deploying.
Image upgrade for SL24 will be copied to flash during image upgrade (bootimage upgrade)
and will not affect the working link until the system is rebooted / power cycled.
Contrary to the FTP method, the TFTP method does not require access to an FTP server, but
instead requires the use of a TFTP client included in many operating systems. Third party tools
such as tftpd32 can also be used.
1. Download the software image from the support portal or FTP server to your local
computer.
2. Note down the current version of the firmware loaded in the radio (CLI version).
3. Connect Management Ethernet port to PC.
4. Configure an IP address in unit if not already done.
5. Start a Telnet or SSH session. Log into the SL-24, go to config node and save your config
if not already saved:
Trango System: Trango StrataLink 24 Command Line Interface v1.2.4
(CLI-view)# config
Password: trango
(CLI-config)# config save
New configuration saved
SUCCESS
6. Turn TFTPd service on the Radio ON with command:
(CLI-config)# tftpd on
7. Send New Firmware Image to target Radio. (This is not done inside the radio and is done
in another window on your local computer.)
Trango Systems Confidential and Proprietary Information
Page 8 of 18
© 2011-2013 Trango Systems, Inc. All rights reserved.
Trango StrataLINK 24
Release Notes v1.2.4
In DOS window, type command:
dos> tftp –i [ip address] put SL24_v1.2.4.tar.gz
ip address
IP Address of the Radio.
In Mac/Linux window, type commands:
# tftp
tftp> mode binary
tftp> connect [radio ip address]
tftp> put SL24_v1.2.4.tar.gz
tftp> quit
8. After the file is transferred to the Radio, use the <bootimage upgrade> command from
the config mode on the radio.
(CLI-config)# bootimage upgrade
................................................................................
................................................................................
.......................................................
SUCCESS
9. After the process returns success, reboot the radio for the new image to be loaded into
active memory.
(CLI-config)# reboot
10. Check the new version on the system with CLI command “version”. It should match with
the versions listed earlier. In case of mismatch version, please perform the upgrade
again from step 1.
FPGA version:
OS version
FW version
Modem Version
0118040E
2p6r22b0D082514
1p2r4D082514
6201.4.4
Please follow all the instructions as listed above in the upgrade instructions. In the case of
version mismatch on the system (local/remote/system) the system is NOT guaranteed to work.
In the event of a power failure during the upgrade process or any mismatch conflict, please open
a support request at support.trangosys.com for further assistance. Serial console remote access
to the OMUs might be required in the event of such failure. It is suggested that all customers
have at least one serial/console cable available at each site.
Please don't make any implicit assumptions.
In case of any doubt please contact technical support for clarification.
Trango Systems Confidential and Proprietary Information
Page 9 of 18
© 2011-2013 Trango Systems, Inc. All rights reserved.
Trango StrataLINK 24
Release Notes v1.2.4
StrataLINK 24 Software Change History
Software Version 1.2.3
Bugs Fixed
1. Power level is set correctly upon initial radio boot up.
FPGA version:
OS version
FW version
Modem Version
0118040E
2p6r22b0D071614
1p2r3D071614
6201.4.4
Software Version 1.2.2
FPGA version:
OS version
FW version
Modem Version
0118040E
2p6r22b0D063014
1p2r2D063014
6201.4.4
Bugs Fixed
1. Bug fix implemented to resolve certain management stability issues.
Software Version 1.2.1
FPGA version:
OS version
FW version
Modem Version
0118040E
2p6r22b0D051214
1p2r1D1051214
6201.4.4
Bugs Fixed
2. Improved transmitter power accuracy when setting TX power lower than -10 dbm
Trango Systems Confidential and Proprietary Information
Page 10 of 18
© 2011-2013 Trango Systems, Inc. All rights reserved.
Trango StrataLINK 24
Release Notes v1.2.4
Software Version 1.2.0
FPGA version:
OS version
FW version
Modem Version
0118040E
2p6r22b0D042314
1p2r0D1042314
6201.4.4
New Features/Enhancements
1. NTP server this feature can be setup through both management interfaces CLI and WEB
interface. User can specify the ntp server ip or name. Local dns server ip is required to
setup server name.
2. Syslog server is supported this can be setup through both management interfaces CLI
and WEB interface.
3. Loglevel has new settings for more detailed reporting in the syslog.
4. Radio configuration file can be exported and imported from the web interface.
Bugs Fixed
3. General enhancement to speed up response time from web interface and command line
interface. This release will also improve overall management stability.
4. Optimized RSSI over temperature variation.
Software Version 1.1.5
FPGA version:
OS version
FW version
Modem Version
0112030D
2p6r22b0D100813
1p1r5D100813
6201.4.4
New Features/Enhancements
1. Timer module enhanced to free up more system processing time to support application
operation
Software Version 1.1.4
FPGA version:
OS version
FW version
0112030D
2p6r22b0D090613
1p1r4D090613
Trango Systems Confidential and Proprietary Information
Page 11 of 18
© 2011-2013 Trango Systems, Inc. All rights reserved.
Trango StrataLINK 24
Release Notes v1.2.4
Modem Version
6201.4.4
Bold typeface indicates new images for this release.
New Features/Enhancements
1. None
Bug fixes
1. Fixed a bug that prevents management of radio from web or cli while still passing traffic
2. Fixed remote link status that displayed “Unlocked” state when the link was “Locked”
3. Fixed problem that would potentially cause traffic to stop after changing the speed
4. Fixed survey function bug in web interface that would sometimes show wrong RSL
5. Fixed loopback_auto display incorrect BER format
6. Adding setting date command on the web interface
7. Fixed Reload cancel bug
Notes
1. Use config as the username for the config login on web interface.
2. RF In/Out counters read slightly lower than actual number of packets going over the air.
GE1 and GE2 port counters are always accurate.
3. Port Priority not functional
4. Pause on/off not functional
5. ACS function removed for this release due to increased time to change speed. This
feature will be added back in next software release.
6. BER on the loopback_auto display may show a small error rate which is decreasing.
Software Version 1.1.2
FPGA version:
0112030D
OS version
2p6r22b0D071613
FW version
1p1r2D071613
Modem Version
6201.4.4
Bold typeface indicates new images for this release.
New Features/Enhancements
8. None
Bug fixes
1. Fixed management interface lockup that occurs when sending SNMP Traps
2. Fixed Reset password button on the web to remove the web config password in addition
to the view password.
Notes
7. Use config as the username for the config login on web interface.
Known Limitations
1. BER is based on CRC errors and might not reflect the accurate BER on live data.
WA: Use External test equipment to measure accurate BER for testing.
Trango Systems Confidential and Proprietary Information
Page 12 of 18
© 2011-2013 Trango Systems, Inc. All rights reserved.
Trango StrataLINK 24
Release Notes v1.2.4
2. Including a space in a password field can cause management unresponsiveness. Ensure
that no spaces are used in passwords. If spaces are included, please provide remote
access to Trango Support for assistance or request RMA for repair.
3. Refreshing the webpage after selecting reboot may cause the radio to reboot again.
WA: Type in the IP address or hostname again instead of using the refresh button.
4. With IBM enabled, broadcast and multicast traffic is limited to 100 Mbps.
5. RF in/out counters read slightly lower than actual number of packets going over the air.
GE1 and GE2 port counters are always accurate.
6. Port priority is not functional at this time.
7. Pause on/off is not functional at this time.
Software Version 1.1
FPGA version:
OS version
FW version
Modem Version
0112030D
2p6r22b0D052013
1p1r0D052013
6201.4.4
New Features/Enhancements
1. Default Configuration: Update some default configuration parameters:
a. 8PSK ACM degrade threshold to -17
b. QPSK up threshold set to -19
c. Tx freq set to 24085
d. Log timer set to 15 seconds
e. Speed mod max set to 1024 and min to QPSK
f. Egress internally set to 40
g. QoS weight default set to: 1, 3, 6, 9
h. DSCP mapping for 18, 20, 22 set to Pri 2
i. Temp max set to 85 degrees
j. Unit ID set to “StrataLink 24”
2. CLI: Remove egress_margin and bootimage toggle from the CLI as they are not relevant
commands.
Bug fixes
1. Misc: Some typo errors on the ACM and symbol rate numbers were corrected.
2. Survey: Fixed a bug with the survey function from the command line interface and the
web. The results will agree with each other now.
Software Version 1.0.9
FPGA version:
OS version
FW version
Modem Version
0112030D
2p6r22b0D043013
1p0r9D043013
6201.4.4
New Features/Enhancements
Trango Systems Confidential and Proprietary Information
Page 13 of 18
© 2011-2013 Trango Systems, Inc. All rights reserved.
Trango StrataLINK 24
Release Notes v1.2.4
1. Management: Added the remote_mgmt command to allow management of the far end
radio through the local out of band management port. This option must be enabled on
both radios for it to function.
2. QoS: Changed the buffer pause thresholds to ensure highest priority traffic is not
dropped when the radio is downshifted to QPSK. The max usable buffer size has
increased slightly as well to:
a. Queue 0 = 103 Kbytes
b. Queue 1 = 105 Kbytes
c. Queue 2 = 107 Kbytes
d. Queue 3 = 118 Kbytes
Bug fixes
1. Misc: Some typo errors on the ACM and symbol rate numbers were corrected.
2. Survey: Fixed a bug with the survey function from the command line interface and the
web. The results will agree with each other now.
Software Version 1.0.8
FPGA version:
OS version
FW version
Modem Version
0112030D
2p6r22b0D041713
1p0r8D041713
6201.4.4
New Features/Enhancements
1. Status remote: Reduce the timer for sending out the current status to the remote unit
from 20 seconds to 5 seconds to speed up the updates on the web interface.
2. Tx Power: Adjust transmit power incrementally by 0.1 dB step size at times when user
configures the power and also when the tx power loop adjusts the power according to
the temperature.
Bug fixes
1. ACM: Make CLI display for acm_info and sysinfo 5 consistent.
2. Counters: Removed dropped air frames from the RF counters since the counter is not
accurately reflecting the correct number of dropped frames.
3. Diagnostic: FPGA checking reported failed in the past, removed the incorrect register.
4. IP: Reconfigure gateway after changing IBM tagging or VLAN ID.
5. Management unresponsiveness: Three events were using the same resource and are
now independent.
6. Web: DSCP QoS mapping adjusted for global setting from per-port.
7. Web: Fixed display of unit_id (remark) to eliminiate trailing characters.
8. Web: Fixed mapping of Tx/Rx PLL to show the correct status.
Software Version 1.0.7
FPGA version:
OS version
0112030D
2p6r22b0D040413
Trango Systems Confidential and Proprietary Information
Page 14 of 18
© 2011-2013 Trango Systems, Inc. All rights reserved.
Trango StrataLINK 24
FW version
Modem Version
Release Notes v1.2.4
1p0r7D040413
6201.4.4
New Features/Enhancements
1. Management: Kernel level change to prevent resource conflicts.
2. QoS: Added Q3 Strict and Q2/Q3 Strict modes to compliment all strict and all WRR.
3. QoS: Enable both 802.1p and diffserv option per active port at system init.
4. QoS: Process QoS priority setting at the system initialization to process the highest
priority available.
5. Tx Power: Issue power command based on the temperature adjusted power level
immediately after setting freq or opmode command instead of waiting for the tx power
maintenance to make the change.
Bug fixes
1. Command Server: Fix related to setting variables.
2. QoS: DSCP priority mapping applies to both ports. Removed the per port mapping in
favor of a global setting.
3. Qos: Egress margin was not saving across reboot.
4. QoS: Update port weight setting to apply to map to CoS queue as opposed to L2 priority.
5. SNMP: Disable all OIDs that do not apply to StrataLINK.
6. Web: Remove unused OIDs like refresh rate.
Software Version 1.0.6
FPGA version:
OS version
FW version
Modem Version
0014030D
2p6r22b0D032513
1p0r6D032513
6201.4.4
New Features/Enhancements
1. ACM: Corrected ACM threshold values.
2. Counters: Display In Discards, Out Discards, CRC Errors and Collision Errors in port
counters via CLI and web interface.
3. Frequency: Validate the user input frequency according to current bandwidth.
4. IBM: Switch the data port when enabling IBM to maintain management connectivity.
5. IBM: Web interface warning message when switching IBM settings.
6. Siglevel: Display both instantaneous and accumulative FER counters in siglevel.
7. Syslog: Provide the ability to update the timer for logging the STAT messages. This
allows the user more or less frequency status updates to be logged.
8. Tx Power: Adjust power level immediately after freq or opmode command instead of
waiting for tx power maintenance to adjust for temperature changes.
Bug fixes
1. Counters: BER calculation based on air frames and current link speed.
Trango Systems Confidential and Proprietary Information
Page 15 of 18
© 2011-2013 Trango Systems, Inc. All rights reserved.
Trango StrataLINK 24
Release Notes v1.2.4
2. Counters: Calculate the RF port rate based on the rx profile speed, not the tx profile
speed.
3. Counters: Change RF total drop error frame to RF total dropped air frames.
4. IBM: Enable MAC address learning in the internal switch to allow natural filtering of
known destination unicast traffic from the IBM port. This removes the previous
limitation of 100 Mbps for traffic with IBM enabled. Broadcast traffic and multicast
traffic will be limited to 100 Mbps with IBM enabled.
5. IBM: Management interface fixed with IBM tagging on to properly configure it with
correct vlan ID at system power up.
6. Loopback: Display the correct number of iterations of loopback_auto via CLI.
7. Survey: Recalculate the average and max RSSI when running through the survey.
Software Version 1.0.5
FPGA version:
OS version
FW version
Modem Version
0001030D
2p6r22b0D030113
1p0r5D030113
6201.4.4
New Features/Enhancements
1. Improved power/RSSI values.
Software Version 1.0.4
FPGA version:
OS version
FW version
Modem Version
0002010D
2p6r22b0D022613
1p0r4D022613
6201.4.4
Bug fixes
1. Configure the modem port with proper tx rx pause setting.
2. Changing IBM VLAN ID with tagging off previously caused gateway to be lost, now the
setting will not change until tagging is enabled.
3. Remove in/out discard counters from CLI and web interface as they were showing
erroneous data.
4. Optimize internal buffer size.
5. Improved ACS reliability through radio to radio messaging.
6. Receive maintenance loop.
7. Added ACS up and down MSE restriction, requires 10 dB difference.
Software Version 1.0.2
FPGA version:
OS version
FW version
Modem Version
0002010D
2p6r22b0D021113
1p0r2D021113
6201.4.4
Trango Systems Confidential and Proprietary Information
Page 16 of 18
© 2011-2013 Trango Systems, Inc. All rights reserved.
Trango StrataLINK 24
Release Notes v1.2.4
Bug fixes
1. Ignore white space at beginning of unit_id and gps_info as a space was being added on
each reboot.
Software Version 1.0.1
FPGA version:
OS version
FW version
Modem Version
0002010D
2p6r22b0D020113
1p0r1D020113
6201.4.4
New Features
1. Egress margin for 200, 300 & 400 Mbps license caps fixed at 25%.
2. Pop-up message to inform user what has been done and what the next steps are when
doing a diagnostic export or config export via web interface.
Bug fixes
1. Broadcasting default MAC as opposed to assigned MAC on bootup.
2. Egress and burst rate setting at startup.
3. Delay management access until system and all applications are ready for operation.
4. Loglevel updated for specific actions: egress margin and throughput capping as well as
power offset message when executed with display as a 0 [SET].
5. License key setting on the web interface.
6. Error checking message for snmp read/write string. Both strings may not be configured
to be the same value.
7. Loopback auto to display RSSI and turn off the internal modem data port to prevent
traffic loopback.
Software Version 1.0.0
FPGA version:
OS version
FW version
Modem Version
0002010D
2p6r22b0D122512
1p0r1D122512
6201.4.4
Key Features
1. Automatic Channel Selection
2. Hitless Adaptive Modulation for all modulations.
3. Native Ethernet support.
4. Packet QoS based on 802.1p
5. GigE supports configurable speed, duplex, rate limiting and jumbo packets.
6. Rapid Port Shutdown
7. CLI access via serial console/SSH/telnet.
8. SNMPv2 support (Trango MIB)
9. Web access supports both secure (HTTPS) and regular (HTTP).
Trango Systems Confidential and Proprietary Information
Page 17 of 18
© 2011-2013 Trango Systems, Inc. All rights reserved.
Trango StrataLINK 24
Release Notes v1.2.4
10. Threshold monitoring.
11. In Band Management with tagging options.
12. Reliable image transfer using FTP, also support TFTP.
Trango Systems Confidential and Proprietary Information
Page 18 of 18
© 2011-2013 Trango Systems, Inc. All rights reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising