AII 23074 Front Ashtray

AII 23074 Front Ashtray
INSTALLATION
INSTRUCTIONS
Accessory
Application
FRONT ASHTRAY
2002 CR-V
Publications No.
AII 23074
Issue Date
NOV 2001
PARTS LIST
3.
Turn the knob clockwise, release the one clip,
and remove the driver’s dashboard under cover.
Front ashtray
DRIVER’S
DASHBOARD
UNDER COVER
Self-tapping screw
CLIP
Illumination harness
KNOB
4 Wire ties
4.
TOOLS REQUIRED
Phillips screwdriver
Stubby Phillips screwdriver
Small flat-tip screwdriver
Remove the driver’s dashboard lower cover:
•
Remove the fuse box cover, and open the
pocket.
•
Remove the two self-tapping screws.
•
Gently pull out on the driver’s dashboard lower
cover to release the eight clips, unplug the
vehicle connector, and remove the lower cover.
VEHICLE CONNECTOR
INSTALLATION
DRIVER’S
DASHBOARD
LOWER
COVER
Customer Information: The information in this
installation instruction is intended for use only by
skilled technicians who have the proper tools,
equipment, and training to correctly and safely add
equipment to your vehicle. These procedures should
not be attempted by “do-it-yourselfers.”
1.
Make sure you have the anti-theft code for the
radio, then write down the frequencies for the
preset buttons.
2.
Disconnect the negative cable from the battery.
RETAINING
TAB (4)
POCKET
CLIP (8)
© 2001 American Honda Motor Co., Inc - All Rights Reserved.
AII 23074
(0111)
Y0599C
SELF-TAPPING
SCREWS
FUSE BOX
COVER
08U25-S9A-1000-91
1 of 4
5.
Open the dashboard pocket.
CLIP (4)
9.
Remove the passenger’s dashboard under cover
(release the three clips and two pins).
CLIP
CLIP (3)
SELFTAPPING
SCREW
RETAINING TAB (2)
6.
7.
DASHBOARD
POCKET
PASSENGER’S
DASHBOARD
UNDER COVER
Remove the dashboard pocket (one self-tapping
screw, and pull out to release the three clips and
two retaining tabs).
Remove the two self-tapping screws that fasten
the heater control panel to the dashboard.
SELF-TAPPING
CLIPS
SCREWS
PIN (2)
10. Remove the two clips and five self-tapping
screws, and pull the dashboard center lower
cover out toward you to release the three clips
and two tabs. Unplug the vehicle 2-pin connector
from the accessory socket and remove the
cover.
VEHICLE 2-PIN
CONNECTOR
Push.
HEATER
CONTROL
PANEL
CLIPS
8.
CLIP
VEHICLE
CONNECTOR
Pull the heater control panel out toward you to
release the four clips. Unplug the vehicle
connector, and remove the heater control panel.
DASHBOARD
CENTER
LOWER
COVER
CLIP
TABS
CLIPS
SELF-TAPPING
SCREW (5)
2 of 4
AII 23074 (0111)
© 2001 American Honda Motor Co., Inc - All Rights Reserved.
11. Remove the beverage holder by pulling it out
toward you while pushing down on its two
retaining tabs.
13. Remove the bracket from the ashtray, then install
the bracket on the dashboard center lower cover
using the two self-tapping screws you just
removed and one self-tapping screw supplied.
Push.
SELFTAPPING
SCREW
(supplied)
RETAINING
TAB
BRACKET
DASHBOARD
CENTER
LOWER COVER
SELF-TAPPING
SCREW (reused)
BEVERAGE
HOLDER
DASHBOARD
CENTER
LOWER
COVER
ASHTRAY
14. Slide the ashtray into position in the cover.
12. Remove the beverage holder bracket (four selftapping screws).
15. Unplug the vehicle 6-pin connector from the fuse
box, and connect the 6-pin connectors of the
illumination harness in between.
VEHICLE 6-PIN
CONNECTOR
FUSE
BOX
SELFTAPPING
SCREWS
(Discard.)
ILLUMINATION
HARNESS 6-PIN
CONNECTORS
SELF-TAPPING
SCREWS (reused)
BEVERAGE
HOLDER
BRACKET
(Discard.)
ILLUMINATION
HARNESS
VEHICLE
HARNESS
DASHBOARD
OPENING
© 2001 American Honda Motor Co., Inc - All Rights Reserved.
AII 23074 (0111)
3 of 4
16. Route the illumination harness to the dashboard
opening along the vehicle harness.
•
If you are also installing the fog lights, unplug
the vehicle 6-pin connector from the fuse box,
and then plug it into the 6-pin connector blacktaped to the fog light switch harness. Plug the
other 6-pin connector of the fog light switch
harness into the 6-pin connector black-taped
to the illumination harness. Finally, plug in the
remaining 6-pin connector of the illumination
harness into the fuse box.
18. Remove the illumination bulb cap from the
illumination bulb, then insert the illumination bulb
into the ashtray, and secure the bulb by turning it
in the direction shown.
ASHTRAY
FUSE BOX 6-PIN
CONNECTOR
VEHICLE 6-PIN
CONNECTOR
ILLUMINATION
BULB
ILLUMINATION
HARNESS 6-PIN
CONNECTORS
ILLUMINATION
BULB CAP
(Discard.)
FOG LIGHT SWITCH
HARNESS 6-PIN
CONNECTORS
17. Secure the illumination harness to the vehicle
harness with four wire ties.
FUSE BOX
19. Reinstall the dashboard center lower cover.
20. Reinstall all removed parts.
21. Check that all wire harnesses are routed properly
and all connectors are plugged in.
VEHICLE
HARNESS
22. Reconnect the negative cable to the battery.
23. Enter the customer’s radio anti-theft code, and
reset the radio station presets.
24. Reset the clock.
NOTE: Whenever the battery is disconnected, the
driver’s AUTO window function is disabled.
25. Start the engine. Push down on the driver’s
window switch until the window is fully open.
ILLUMINATION
HARNESS
WIRE TIES
26. Pull up on the driver’s window switch to close the
window completely, then hold the switch for a
second or two more.
27. Test the AUTO window function.
Replacment Bulb
P/N: 35505-692-0030
Specification: 14 V, 1.4 W
4 of 4
AII 23074 (0111)
© 2001 American Honda Motor Co., Inc - All Rights Reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement