AirLive WL-5460AP Manual

AirLive WL-5460AP Manual
WL-5450AP & WL-5460AP
Wireless Access Point
User’s Guide
1
FCC Certifications
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
y
Reorient or relocate the receiving antenna.
y
Increase the separation between the equipment and receiver.
y
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
y
Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
Any changes or modifications not expressly approved by the grantee of this device could void the
user’s authority to operate the equipment.
This device complies with Part 15 of the FCC rules.
conditions:
Operation is subject to the following two
(1) This device may not cause harmful interference, and (2) This device must accept
any interference received, including interference that may cause undesired operation.
FCC RF Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of 20cm
between the radiator and your body.
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause radio interference,
in which case the user may be required to take adequate measures.
All trademarks and brand names are the property of their respective proprietors.
Specifications are subject to change without prior notification.
2
Table of Content
Introduction............................................................................................................................................................4
FEATURES ...................................................................................................................................................................4
APPLICATION ..............................................................................................................................................................5
PARTS NAMES AND FUNCTIONS ...............................................................................................................................6
FACTORY DEFAULT SETTINGS ..................................................................................................................................8
WL-5450AP & WL-5460AP.....................................................................................8
Hardware Connection........................................................................................................................................9
Check the LEDs:..................................................................................................9
About the Operation Modes .........................................................................................................................10
ACCESS POINT MODE .............................................................................................................................................10
WDS REPEATER MODE ...........................................................................................................................................11
CLIENT MODE (INFRASTRUCTURE) ........................................................................................................................12
CLIENT MODE (AD-HOC) .......................................................................................................................................13
WDS BRIDGE MODE ...............................................................................................................................................14
Configuration........................................................................................................................................................15
LOGIN .......................................................................................................................................................................15
STATUS .....................................................................................................................................................................16
System ............................................................................................................ 16
System Log ...................................................................................................... 18
Statistics .......................................................................................................... 18
WIRELESS ................................................................................................................................................................19
Basic Settings ................................................................................................... 19
Advanced Settings ............................................................................................. 21
Security ........................................................................................................... 24
Access Control .................................................................................................. 27
Site Survey....................................................................................................... 28
WDS Setting ..................................................................................................... 28
TCP/IP.....................................................................................................................................................................30
Basic ............................................................................................................... 30
OTHER ......................................................................................................................................................................32
Upgrade Firmware ............................................................................................. 32
Save/Reload Settings ......................................................................................... 32
Password.......................................................................................................... 34
3
INTRODUCTION
AirLive WL-5450AP/WL-5460AP is an IEEE802.11b/g compliant 11 Mbps & 54 Mbps Ethernet
Wireless Access Point. The Wireless Access Point is equipped with two 10/100 M Auto-sensing
Ethernet ports for connecting to LAN and also for cascading to next Wireless Access Point.
AirLive WL-5450AP/WL-5460AP provides 64/128bit WEP encryption, WPA and IEEE802.1x
which ensures a high level of security to protect users’ data and privacy.
The MAC Address filter
prevents the unauthorized MAC Addresses from accessing your Wireless LAN. Your network
security is therefore double assured.
The web-based management utility is provided for easy configuration that your wireless network
connection is ensured to be always solid and hassle free.
Features
1.
Two LAN ports for Wireless AP cascade.
2.
Support WPA.
3.
Support AP client mode.
4.
Support WDS for bridge mode.
5.
Support data rate automatic fallback.
6.
Automatic channel selection.
7.
Client access control.
8.
Support 802.1x/Radius client with EAP-TLS, TKIP, AES encryption.
9.
Support IAPP.
10.
Adjustable Tx power, Tx rate, and SSID broadcast.
11.
Allow WEP 64/128 bit.
•
Web interface management.
12.
Support System event log and statistics.
13.
MAC filtering (For wireless only).
4
Application
Example 1
Example 2
5
Parts Names and Functions
1. Front Panel: (LED Indicators)
LED
Indicator
1
Power
Status
Color
Green
Solid
Flashing
Turns solid green when power is
N/A.
applied to this device.
2
Status
Red
Turns solid red when the device is
booting, after boot successfully,
the light turn off.
3~6
Link/Act.
Green
Wireless
Turns solid green when connected Receiving/
and associated to at least a client Sending data
station.
WEP/WPA
Orange
Turns solid orange when wireless N/A
security is enabled.
MAC Ctrl
Orange
Turns solid orange when MAC
N/A
Control is enabled.
Bridge /
Orange
Repeater
7
LAN 1
8
LAN 2
Turn solid orange when Bridge or N/A
Repeater is enabled.
Green
Turns solid green when linked to a Receiving/
local network.
Table 1: LED Indicators
6
Sending data
2. Rear Panel: Connection Ports
Port/button
Functions
A
12V DC
Connects the power adapter plug
B
LAN1
Connects to Ethernet
C
LAN2
Connects to Ethernet
D
(Factory)
Press over 3 seconds to reboot this device.
RESET
Press for over 10 seconds to restore factory settings.
Performing the Factory Reset will erase all previously
entered device settings.
Table 2: Connection Ports
7
Factory Default Settings
Setting
Wireless Access Point
Device Name
WL-5460AP
SSID
Default value: airlive
Channel
11
WEP
Default value: Disabled
IP Address
192.168.100. 252
ƒ
8
HARDWARE CONNECTION
Note: Before you starting hardware connection, you are advised to find an appropriate location to
place the Access Point. Usually, the best place for the Access Point is at the center of your wireless
network, with line of straight to all your wireless stations. Also, remember to adjust the antenna;
usually the higher the antenna is placed, the better will be the performance.
1. Connect to your local area network: connect a Ethernet cable to one of
the Ethernet port (LAN1 or LAN2) of this Wireless Access Point, and the other
end to a hub, switch, router, or another wireless access point.
2. Power on the device: connect the included AC power adapter to the
Wireless Access Point’s power port and the other end to a wall outlet.
Check the LEDs:
The Power and LAN # LEDs should be ON. LAN# LED will even blink if there is traffic.
The Link/Act LED will be on in static when associated with a station and blink whenever this AP
receives data packets in the air.
If the Status LED glows after self-test , it means this Wireless Access Point fails on self test.
Please ask your dealer for technical support.
3. Configure your PC: Make sure your local PC(s) has wireless network adapter
installed.
9
ABOUT THE OPERATION MODES
This device provides four operational applications with Access Point, Bridge,
Client (Ad-hoc) and Client (Infrastructure) modes, which are mutually
exclusive.
This device is shipped with configuration that is functional right out of the box. If
you want to change the settings in order to perform more advanced configuration
or even change the mode of operation, you can use the web-based utility
provided by the manufacturer as described in the following sections.
Access Point Mode
When acting as an access point, this device connects all the stations
(PC/notebook with wireless network adapter) to a wired network. All stations can
have the Internet access if only the Access Point has the Internet connection.
See the sample application below.
To set the operation mode to Access Point, please go to “Wireless JBasic
Settings”, in the “Mode” field click the down arrow b to select AP mode.
10
WDS Repeater Mode
Refer to the illustration below. While acting as Bridges, AP1 (with Station 1 being
associated to) and AP2 (with Station 2 being associated) can communicate with
each other through wireless interface (with WDS). Thus Station 1 can
communicate with Station 2 and both Station 1 and Station 2 are able to access
the Internet if only AP1 or AP2 has the Internet connection.
To set the operation mode to Bridge, please go to “Wireless JBasic Settings”,
in the “Mode” field click the down arrow b to select AP mode. And go to
“Wireless JWDS Settings” to enable WDS.
Note:
To act as Bridge, both AP1 and AP2 must have WDS enabled and add
each other as its WDS Access Point. (e.g. Add AP2’s MAC address to
AP1’s “WDS AP List” and vice versa)
11
Client Mode (Infrastructure)
If set to Client (Infrastructure) mode, this device can work like a wireless station
when it’s connected to a computer so that the computer can send packets from
wired end to wireless interface.
Refer to the illustration below. This station (AP1 plus the connected computer 1) can associate to
another Access Point (AP2), and then can have the Internet access if the other Access Point (AP2)
has the Internet connection.
To set the operation mode to Client (Infrastructure), please go to “Wireless
JBasic Settings”, in the “Mode” field click the down arrow b to select Client
mode, and then select “Network Type” as “Infrastructure”.
12
Client Mode (Ad-hoc)
If set to the Client (Ad-hoc) mode, this device can work like a wireless station
when it is connected to a computer so that the computer can send packets from
wired end to wireless interface. You can share files and printers between
wireless stations (PC and laptop with wireless network adapter installed).
See the sample application below.
To set the operation mode to Client (Ad-hoc), please go to “Wireless JBasic
Settings”, in the “Mode” field click the down arrow b to select Client mode, and
then select Network Type as “Ad-hoc”.
13
WDS Bridge Mode
The WDS (Wireless Distributed System) function let this access point acts as a
wireless LAN access point and repeater at the same time. Users can use this
feature to build up a large wireless network in a large space like airports, hotels
and schools …etc. This feature is also useful when users want to bridge networks
between buildings where it is impossible to deploy network cable connections
between these buildings.
14
CONFIGURATION
Login
1.
Start your computer. Connect an Ethernet cable between your computer and the Wireless
Access Point.
2.
Make sure your wired station is set to the same subnet as the Wireless Access Point, i.e.
192.168.100.252
3.
Start your WEB browser. In the Address box, enter the following:
HTTP://192.168.100.252
The configuration menu is divided into four categories: Status, Wireless, TCP/IP, and
Other settings. Click on the desired setup item to expand the page in the main navigation
page. The setup pages covered in this utility are described below.
15
Status
In this screen, you can see the current settings and status of this Access Point. You can
change settings by selecting specific tab described in below.
System
System
Uptime
The time period since the device was up.
Firmware Version The current version of the firmware installed in this device.
Wireless Configuration
Wireless Mode
There are four modes supported, Access Point, Client (Ad-hoc and
Infrastructure), WDS Bridge and WDS repeater. The default mode is
Access Point. If you want to change to bridge mode, please go to
Wireless/WDS Setting to enable the WDS function.
SSID
The SSID differentiates one WLAN from another; therefore, all access
points and all devices attempting to connect to a specific WLAN must use
the same SSID. It is case-sensitive and must not exceed 32 characters. A
device will not be permitted to join the BSS unless it can provide the
16
unique SSID. An SSID is also referred to as a network name because
essentially it is a name that identifies a wireless network.
Channel Number
The number of channels supported depends on the region of this Access
Point. All stations communicating with the Access Point must use the
same channel.
Encryption
WEP Encryption (Wired Equivalent Privacy) is set to Disabled by default.
When WEP is enabled, data packet is encrypted
before being transmitted. The WEP prevents data packets from being
eavesdropped by unrelated people. By using WEP data encryption, there
may be a significant degradation of the data throughput on the wireless
link.
Associated Clients Displays the total number of clients associated to this AP. You can have up
to 64 clients to associate to this Access Point.
BSSID
BSSID displays the ID of current BSS, which uniquely identifies each
BSS. In AP mode, this value is the MAC address of this Access Point.
TCP/IP Configuration
IP Protocol
Display the method to get the IP of this AP, which could be obtained by
Fixed-IP or DHCP-client.
br0 IP Address
Current IP address for this Access Point
br0 Subnet Mask
Current Subnet mask for this Access Point
br0
Default Default Gateway for this Access Point
Gateway
br0 MAC Address
The MAC Address for this Access Point
17
System Log
This page display log events with time when events happened, log events’ types, log sources and
the description for events themselves. System manager can use the system log to trace when
problems occur.
Statistics
The Statistics table shows the packets sent/received over wireless and ethernet LAN respectively.
18
Wireless
Basic Settings
This page includes all primary and major parameters.
Any parameter change will cause the
device to reboot for the new settings to take effect.
… Disable Wireless LAN Check the box to disable the Wireless LAN Interface, by so doing,
Interface
you won’t be able to make wireless connection with this Access
Point in the network you are located. In other words, this device will
not be visible by any wireless station.
Band
You can choose one mode of the following you need.
~ 2.4GHz (B): 802.11b supported rate only.
~ 2.4GHz (G): 802.11g supported rate only.
~ 2.4GHz (B+G): 802.11b supported rate and 802.11g supported
rate.
The default is 2.4GHz (B+G) mode.
Mode
This Wireless Access Point can support four modes AP, Client,
Bridge and Repeater.
(Refer to page 7-11 for detailed
information)
Network Type
When in Client mode, you can select between Ad-Hoc and
Infrastructure.
19
SSID
The SSID differentiates one WLAN from another; therefore, all
access points and all devices attempting to connect to a specific
WLAN must use the same SSID. It is case-sensitive and must not
exceed 32 characters. A device will not be permitted to join the
BSS unless it can provide the unique SSID. An SSID is also referred
to as a network name because essentially it is a name that
identifies a wireless network.
Region Domain
The AP’s domain determines the channel number.
Channel Number
Allow user to set the channel manually or automatically.
If set channel manually, just select the channel you want to specify.
If “Auto” is selected, user can set the channel range to have
Wireless Access Point automatically survey and choose the channel
with best situation for communication.
The number of channels supported depends on the region of this
Access Point. All stations communicating with the Access Point
must use the same channel.
…Enable
Mac
Clone If your ISP restricts service to PCs only, use the MAC Clone feature
(Single Ethernet Client)
to copy a PC Media
Access Control (MAC) address to your router. This procedure will
cause the router to appear
as a single PC, while allowing online access to multiple computers
on your network.
Apply Changes
Press to save the new settings on the screen.
Reset
Press to discard the data you have entered since last time you press
Apply Change.
20
Advanced Settings
It is not recommended that settings in this page to be changed unless advanced users want to
change to meet their wireless environment for optimal performance
Authentication Type
To provide a certain level of security, the IEEE 802.11 standard has
defined two types of authentication methods, Open System and
Shared Key. With Open System authentication, a wireless PC can join
any network and receive any messages that are not encrypted. With
Shared Key authentication, only those PCs that possess the correct
authentication key can join the network. By default, IEEE 802.11
wireless devices operate in an Open System network.
Wired Equivalent Privacy (WEP) data encryption is used when the
wireless
devices
are
configured
to
operate
in
Shared
Key
authentication mode.
If the Access Point is using Open System, then the wireless adapter
will need to be set to the same authentication mode.
Shared Key is used when both the sender and the recipient share a
secret key.
Select Auto for the network adapter to select the Authentication
mode automatically depending on the Access Point Authentication
21
mode.
Fragment Threshold
Fragmentation mechanism is used for improving the efficiency
when high traffic flows along in the wireless network. If your
802.11g Wireless LAN PC Card often transmit large files in wireless
network, you can enter new Fragment Threshold value to split the
packet. The value can be set from 256 to 2346. The default value
is 2346.
RTS Threshold
RTS Threshold is a mechanism implemented to prevent the “Hidden
Node” problem. “Hidden Node” is a situation in which two stations are
within range of the same Access Point, but are not within range of
each other. Therefore, they are hidden nodes for each other. When a
station starts data transmission with the Access Point, it might not
notice that the other station is already using the wireless medium.
When these two stations send data at the same time, they might
collide when arriving simultaneously at the Access Point. The collision
will most certainly result in a loss of messages for both stations.
Thus, the RTS Threshold mechanism provides a solution to
prevent data collisions. When you enable RTS Threshold on a
suspect “hidden station”, this station and its Access Point will
use a Request to Send (RTS). The station will send an RTS to
the Access Point, informing that it is going to transmit the
data. Upon receipt, the Access Point will respond with a CTS
message to all station within its range to notify all other
stations to defer transmission. It will also confirm the
requestor station that the Access Point has reserved it for the
time-frame of the requested transmission.
If the “Hidden Node” problem is an issue, please specify the packet
size. The RTS mechanism will be activated if the data size exceeds the
value you set.. The default value is 2347.
Warning: Enabling RTS Threshold will cause redundant network
overhead that could negatively affect the throughput performance
instead of providing a remedy.
This value should remain at its default setting of 2347.
Should you
encounter inconsistent data flow, only minor modifications of this value are
recommended.
Beacon Interval
Beacon Interval is the amount of time between beacon transmissions.
22
Before a station enters power save mode, the station needs the
beacon interval to know when to wake up to receive the beacon (and
learn whether there are buffered frames at the access point).
Data Rate
By default, the unit adaptively selects the highest possible rate for
transmission. Select the basic rates to be used among the following
options: Auto, 1, 2, 5.5, 11or 54 Mbps. For most networks the default
setting is Auto which is the best choice. When Auto is enabled the
transmission rate will select the optimal rate. If obstacles or
interference are present, the system will automatically fall back to a
lower rate.
Preamble Type
A preamble is a signal used in wireless environment to synchronize
the transmitting timing including Synchronization and Start frame
delimiter. In a "noisy" network environment, the Preamble Type
should be set to Long Preamble. The Short Preamble is intended
for
applications
where
minimum
overhead
and
maximum
performance is desired. If in a "noisy" network environment, the
performance will be decreased.
Broadcast SSID
Select enabled to allow all the wireless stations to detect the SSID of
this Access Point.
IAPP
IAPP (Inter Access Point Protocol) is designed for the enforcement of
unique association throughout a ESS (Extended Service Set) and a
secure exchange of station’s security context between current access
point (AP) and new AP during handoff period.
802.11g Protection
The 802.11g standard includes a protection mechanism to ensure mixed
802.11b and 802.11g operation. If there is no such kind of mechanism exists,
the two kinds of standards may mutually interfere and decrease network’s
performance.
Apply Change
Press to save the new settings on the screen.
Reset
Press to discard the data you have entered since last time you press
Apply Change.
23
Security
Here you can configure the security of your wireless network. Selecting different method will
enable you to have different level of security. Please note that by using any encryption, by which
data packet is encrypted before transmission to prevent data packets from being eavesdropped
by unrelated people, there may be a significant degradation of the data throughput on the
wireless link.
Encryption: None (Encryption is set to None by default.)
If Use 802.1x Authentication is selected, the RADIUS Server will proceed to check the 802.1x
Authentication.
Encryption: WEP
If WEP is selected, users will have to Set WEP keys either manually, or select to Use 802.1x
Authentication to make the RADIUS server to issue the WEP key dynamically.
24
Set WEP key
ƒ
Click the Set WEP Keys will prompt you a window to set 64bit or
128bit Encryption.
ƒ
Select HEX if you are using hexadecimal numbers (0-9, or A-F).
Select ASCII if you are using ASCII characters (case-sensitive).
ƒ
Ten hexadecimal digits or five ASCII characters
are needed if
64-bit WEP is used; 26 hexadecimal digits or 13 ASCII
characters are needed if 128-bit WEP is used.
Encryption: WPA (TKIP)
WPA (TKIP): If WPA is selected, users will have to select the Authentication modes between
Enterprise (RADIUS) and Personal (Pre-shared Key).
Pre-shared Key
Pre-Shared-Key serves as a password. Users may key in a 8 to 63
characters string to set the password or leave it blank, in which the
802.1x Authentication will be activated. Make sure the same password
is used on client's end.
There are two formats for choice to set the Pre-shared key, i.e.
Passphrase and Hex. If Hex is selected, users will have to enter a 64
characters string. For easier configuration, the Passphrase (at least 8
characters) format is recommended.
Group Key Life Time Enter the number of seconds that will elapse before the group key
25
change automatically. The default is 86400 seconds.
Enable
The two most important features beyond WPA to become standardized
Pre-Authentication
through 802.11i/WPA2 are: pre-authentication, which enables secure
fast roaming without noticeable signal latency.
Preauthentication provides a way to establish a PMK security association
before a client associates. The advantage is that the client reduces the
time that it's disconnected to the network.
Authentication
Port: Enter the RADIUS Server’s port number provided by your ISP. The
RADIUS Server
default is 1812.
IP Address: Enter the RADIUS Server’s IP Address provided by your
ISP.
Password: Enter the password that the AP shares with the RADIUS
Server.
Apply Change
Press to save the new settings on the screen.
Reset
Press to discard the data you have entered since last time you press
Apply Change.
26
Access Control
When Enable Wireless Access Control is checked, only those clients whose wireless MAC
addresses listed in the access control list can access this Access Point. If the list contains no
entries with this function being enabled, then no clients will be able to access this Access Point.
Wireless
Access Select the Access Control Mode from the pull-down menu.
Control Mode
Disable: Select to disable Wireless Access Control Mode.
Allow Listed: Only the stations shown in the table can associate with the
AP.
Deny Listed: Stations shown in the table won’t be able to associate with
the AP.
MAC Address
Enter the MAC Address of a station that is allowed to access this Access
Point.
Comment
You may enter up to 20 characters as a remark to the previous MAC
Address.
Apply Changes
Press to save the new settings on the screen.
Reset
Press to discard the data you have entered since last time you press Apply
Change.
Delete Selected
To delete clients from access to this Access Point, you may firstly check the
Select checkbox next to the MAC address and Comments, and press
Delete Selected.
Delete All
To delete all the clients from access to this Access Point, just press Delete
All without selecting the checkbox.
Reset
If you have made any selection, press Reset will clear all the select mark.
27
Site Survey
Site survey displays all the active Access Points and IBSS in the neighborhood. When you are in
the client mode, you can select one AP to associate.
Press Refresh to get the latest information.
WDS Setting
To enable WDS function will let this AP enter “Bridge Mode”.
Two APs in bridge modes can
communicate with each other through wireless interface. That is, two stations associated to
different AP in bridge mode can communicate with each other.
† Enable WDS
Check the checkbox to enable WDS, all of the WDS settings in this
screen can be enabled only when WDS or AP+WDS is selected in
Wireless Basic Settings screen (See page 19).
28
Add WDS AP
MAC Address: Enter the MAC Address for the Access Point to establish
WDS
Comment: You may enter up to 20 characters as a remark to the
previous MAC Address.
Apply Changes
Press to save the new settings on the screen.
Reset
Press to discard the data you have entered since last time you press
Apply Change.
Set Security
Click to set the WDS security, please refer to the previous Wireless
Security Setup section (Page 27).
Show Statistics
Click
to
show
the
detailed
information
for
each
WDS
AP.
Current WDS AP List
The added Access Points for participating WDS with this Access Point
are shown.
Delete Selected
You can delete the WDS Access Points listed above by marking the
checkbox.
Delete All
You can delete all of the WDS Access Points listed above.
Reset
Press to discard the data you have entered since last time you press
Apply Change.
29
TCP/IP
Basic
In this page, you can change the TCP/IP settings of this Access Point, select to enable/disable the
DHCP Client, 802.1d Spanning Tree, and Clone MAC Address.
IP Address
This field can be modified only when DHCP Client is disabled. If your
system manager assigned you static IP settings, then you will have to
enter the information provided.
Subnet Mask
Enter the information provided by your system manager.
Default
Enter the information provided by your system manager.
Gateway
DHCP
Select Disable, Client or Server from the pull-down menu.
Disable: Select to disable DHCP server function.
Client: Select to automatically get the LAN port IP address from ISP (For
ADSL/Cable Modem).
Server: Select to enable DHCP server function.
DHCP
Client
WL-5060AP
IP
addresses
continuing
Range
192.168.100.253
Show Client
Click to show Active DHCP Client table.
30
from
192.168.100.1
to
DNS Server
Enter the Domain Name Service IP address.
802.1d
To enable 802.1d Spanning Tree will prevent the network from
Spanning Tree
infinite loops. Infinite loop will happen in the network when WDS is
enabled and there are multiple active paths between stations.
Clone
MAC
You can specify the MAC address of your Access Point to replace the
Address
factory setting.
Apply Change
Press to save the new settings on the screen.
Reset
Press to discard the data you have entered since last time you press Apply
Change.
31
Other
Upgrade Firmware
1. Download the latest firmware from your distributor and save the file on the hard drive.
2. Start the browser, open the configuration page, click on Other, and click Upgrade
Firmware to enter the Upgrade Firmware window. Enter the new firmware’s path and
file name (i.e. C:\FIRMWARE\firmware.bin). Or, click the Browse button, find and open
the firmware file (the browser will display to correct file path).
3. Click Reset to clear all the settings on this page. Or click Upload to start the upgrade.
Save/Reload Settings
This function enables users to save the current configurations as a file (i.e. config.dat) To
load configuration from a file, enter the file name or click Browse… to find the file from your
computer.
32
Save Settings to File: Click SAVE..
to save the current configuration to file.
When prompted the upper left screen, select “Save this file to disk”, and the upper right
screen will prompt you a dialog box to enter the file name and the file location.
Load Settings From File: Click Browse… if you want to load a pre-saved file, enter the file
name with the correct path and then click on Upload. Or click Browse… to select the file.
Reset: Click to restore the default configuration.
33
Password
For secure reason, it is recommended that you set the account to access the web server of this
Access Point. Leaving the user name and password blank will disable the protection. The login
screen prompts immediately once you finish setting the account and password. Remember your
user name and password for you will be asked to enter them every time you access the web
server of this Access Point.
User Name
Enter your new user name to access the web server. User name can be up
to 30 characters long. User name can contain letter, number and space.
It is case sensitive.
New Password
Set your new password. Password can be up to 30 characters long.
Password can contain letter, number and space. It is case sensitive.
Confirm Password
Re-enter the new password for confirmation.
Apply Change
Press to save the new settings on the screen.
Reset
Press to discard the data you have entered since last time you press Apply
Change.
34
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement