Instruction Manual - Test Equipment Depot

Instruction Manual - Test Equipment Depot
Instruction
Manual
ENGLISH
CL200
Instruction Manual
CL200
General Specifications
The Klein Tools CL200 is a multi-featured clamp meter. It measures
AC / DC voltage, AC current, resistance, capacitance, frequency, duty cycle,
and temperature. It can also test diodes and continuity.
ENGLISH
• 3-3/4 DIGIT
3999 COUNT LCD
• AUTO / MANUAL
RANGE
• DATA HOLD
• WORKLIGHT
AUTO
AC
A
For Professionals...Since 1857®
CL200
• BACKLIGHT
•
•
•
•
•
•
•
•
•
•
•
•
Operating Altitude: 2000 meters
Relative Humidity: 75% max
Operating Temperature: 0°C / 32°F to 40°C / 104°F
Storage Temperature: -10°C / 14°F to 50°C / 122°F
Accuracy Temperature: 18°C / 64°F to 28°C / 82°F
Temperature Coefficient: 0.1*(specified accuracy) / °C
Sampling Frequency: 3 samples per second
Dimensions: 8.2" x 3.0" x 1.4"
Weight: 10.0 oz.
Calibration: Accurate for one year
CAT Rating: CAT III 600V
Accuracy: ± (% of reading + # of least significant digits)
WARNINGS
To ensure safe operation and service of the tester, follow these instructions.
Failure to observe these warnings can result in severe injury or death.
• Before each use, verify meter operation by measuring
a known voltage or current.
• Never use the meter on a circuit with voltages that exceed the
category based rating of this meter.
• Do not use the meter during electrical storms, or in wet weather.
• Do not use the meter or test leads if they appear to be damaged.
• Ensure meter leads are fully seated, and keep fingers away from
the metal probe contacts when making measurements.
• Do not open the meter to replace batteries while the probes
are connected.
• Use caution when working with voltages above 60V DC,
or 25V AC RMS. Such voltages pose a shock hazard.
• To avoid false readings that can lead to electrical shock,
replace batteries if a low battery indicator appears.
• Unless measuring voltage or current, shut off and lock out
power before measuring resistance or capacitance.
• Always adhere to local and national safety codes. Use individual
protective equipment to prevent shock and arc blast injury where
hazardous live conductors are exposed.
SYMBOLS
~
99 Washington Street
Melrose, MA 02176
Phone 781-665-1400
Toll Free 1-800-517-8431
Visit us at www.TestEquipmentDepot.com
AC Alternating Current
Warning or Caution
DC Direct Current
Dangerous levels
DC/AC Voltage or Current
Double Insulated Class II
Ground
Safe for disconnect
from live conductors
AC Source
ENGLISH
H.
Feature Details
Backlight / Worklight
•
•
•
•
1
H
B
Hold button down to enable worklight and backlight.
On release, lights will turn off automatically after 5 to 15 seconds.
Worklight only operates during AC current measurement.
Using lights drains the battery significantly.
Auto Power-Off
• Device will power off after 30 minutes non-use.
• Turn the dial or press a button to wake.
• Press the HOLD button while turning on to disable
Auto Power-Off feature.
Function Instructions
CL200
G
CL200
On Back
1
H
5
D
C
3
E
AUTO
AC
4
2
F
1.
A
AC Current: < 600A
Features: HOLD
RANGE
WORKLIGHT
A
A.
Use CAT III rated leads or higher.
Do not attempt to measure more than 600V or
any current on lead input.
B.
Keep hands below line when measuring high current levels.
C.
Select Functionality Button
• Switch between AC and DC.
• Switch between Ω,
,
, and
D.
• Center wire in guides for best accuracy.
• Opposing currents cancel (use line-splitter when necessary).
2.
AC / DC Voltage: < 600V
Features: HOLD
.
RANGE
PRESS
Data Hold
AUTO
AUTO
• Press to hold the current input on the display.
• Press again to return to live reading.
E.
AC
A
AC
A
Auto / Manual Range
• Press repeatedly to cycle through manual ranges.
• Hold for 2 seconds to return to auto ranging mode.
• AUTO is displayed on LCD only during auto ranging mode.
F. G. Battery Replacement
• When
indicator is displayed on the LCD,
batteries must be replaced.
• Remove the back screw and replace 3 x AAA batteries.
• Select AC or DC voltage source.
3.
Frequency (Hz) / Duty Cycle
Features: HOLD
PRESS
AUTO
AC
Duty
A
ENGLISH
Temperature: -4° ≤ °F ≤ 1832°
4.
Electrical Specifications
Features: HOLD
DC Voltage Measurement
AC
A
Range
5.
Resolution
400mV
0.1mV
4V
0.001V
40V
0.01V
• Use included thermocouple.
400V
0.1V
Resistance / Capacitance / Diode / Continuity
600V
1V
PRESS
TO SELECT
Resistance
Diode
Capacitance
Continuity
Resistance Features:
HOLD
AUTO
AC
A
•
•
RANGE
Ω < 40MΩ
Do not measure resistance
on a live circuit.
Capacitance Features:
HOLD
AUTO
AC
RANGE
A
• F < 100μF
• Wait up to 60 seconds for measurement.
•
Safely discharge capacitor before
measurement.
Diode Features:
AUTO
AC
HOLD
A
Display shows:
• Forward voltage drop if forward biased.
• “O.L.” if reverse biased.
Continuity Features:
AUTO
AC
HOLD
A
• Display shows resistance.
• Buzzer sounds if less than 60Ω
Accuracy
± (0.8% + 2 digits)
± (1.0% + 2 digits)
Overload Protection: 600V DC / AC
Input Impedance: 10MΩ.
AC Voltage Measurement
Range
Resolution
400mV
0.1mV
4V
0.001V
40V
0.01V
400V
0.1V
600V
1V
Accuracy
± (1.0% + 10 digits)
± (1.2% + 10 digits)
Overload Protection: 600V DC / AC
Frequency: 40 to 400Hz
Input Impedance: 10MΩ.
Response: Averaging
AC Current Measurement
Range
Resolution
Accuracy
4A
0.001A
± (3.5% + 20 digits) ≤ 0.5A
4A
0.001A
± (3.0% + 10 digits) > 0.5A
40A
0.01A
± (3.0% + 10 digits)
400A
0.1A
± (2.5% + 10 digits)
600A
1A
± (1.5% + 5 digits)
Overload Protection: 720A for 60 sec. max
Frequency: 50 to 60Hz
Response: Averaging
Resistance Measurement
Range
Resolution
400Ω
0.1Ω
DC Measurement
4kΩ
0.001kΩ
Auto Range Active
40kΩ
0.01kΩ
Current in Amps
400kΩ
0.1kΩ
Diode Test
4MΩ
0.001MΩ
Continuity Test
40MΩ
0.01MΩ
Symbols used on LCD
~
-
AC Measurement
Negative DC Value
Low Battery
H
Hold Active
V
Hz
F
Ω
m
n
Voltage Measurement
Frequency in Hertz
Capacitance in Farads
Resistance in Ohms
Milli 10-3
Nano 10-9
AUTO
A
%
°F
M
k
μ
Duty Cycle
Temperature in Fahrenheit
Mega 106
Kilo 103
Micro 10-6
Overload Protection: 600V DC / AC
Accuracy
± (1.2% + 2 digits)
± (2.0% + 5 digits)
ENGLISH
Capacitance Measurement
Range
Resolution
Accuracy
50nF
0.01nF
± (3.0% + 10 digits)
500nF
0.1nF
5µF
0.001µF
50µF
0.01µF
100µF
0.1µF
± (3.0% + 5 digits)
Overload Protection: 600V DC / AC
Frequency Measurement
Range
Resolution
50Hz
0.01Hz
500Hz
0.1Hz
5kHz
0.001kHz
50kHz
0.01kHz
100kHz
0.1kHz
Accuracy
± (0.1% + 3 digits)
Warranty
This product is warranted to be free from defects in materials and workmanship
for a period of two years from the date of purchase. During this warranty period,
Klein Tools has the option to repair or replace or refund the purchase price of
any unit which fails to conform to this warranty under normal use and service.
This warranty does not cover damage which occurs in shipment or failure which
results from alteration, tampering, accident, misuse, abuse, neglect, or improper
maintenance. Batteries and damage resulting from failed batteries are not
covered by warranty. A purchase receipt or other proof of original purchase date
will be required before warranty repairs will be rendered.
Any implied warranties, including but not limited to implied warranties of
merchantability and fitness for a particular purpose, are limited to the express
warranty. Klein Tools shall not be liable for loss of use of the instrument or other
incidental or consequential damages, expenses, or economic loss, or for any
claim or claims for such damage, expenses or economic loss.
Some states or countries laws vary, so the above limitations or exclusions may
not apply to you. This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state. If your Klein product requires
repair or for information on how to exercise your rights under the terms of this
warranty, please contact Klein Tools at 1-877-775-5346.
CLEANING
Overload Protection: 600V DC / AC
Turn instrument off and disconnect test leads. Clean the instrument by using
a damp cloth. Do not use abrasive cleaners or solvents.
Duty Cycle Measurement
Range
Resolution
Accuracy
0.1 ˜ 99.9%
0.1%
± (3.0% + 0 digits)
Overload Protection: 600V DC / AC
Temperature Measurement
Range
Resolution
Accuracy
-4 ˜ 1832°F
1°F
± (3.0% + 3 digits)
Overload Protection: 600V DC / AC
STORAGE
Remove the batteries when instrument is not in use for a prolonged period of
time. Do not expose to high temperatures or humidity. After a period of storage
in extreme conditions exceeding the limits mentioned in the Specifications
section, allow the instrument to return to normal operating conditions before
using it.
Disposal / Recycle
Caution: This symbol indicates that equipment and its accessories
shall be subject to a separate collection and correct disposal.
Diode Test
Overload Protection
Resolution
Open Circuit Voltage
600V DC / AC
1mV
Appx. 1.5V
Overload Protection
Resolution
Open Circuit Voltage
600V DC / AC
100mΩ
Appx. 0.45V
Continuity Test
CUSTOMER SERVICE
KLEIN TOOLS, INC.
450 Bond Street
Lincolnshire, IL 60069
1-877-775-5346
www.kleintools.com
139560T
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising