Tennant T5 Scrubber-Dryer Operator Manual

Below you will find brief information for Scrubber-Dryer T5. The T5 is a scrubber-dryer that can be used to clean hard floors in an indoor environment. It features a variety of cleaning options, including conventional scrubbing, foam scrubbing, and electrically converted water scrubbing.

PDF Download

Document

Scrubber--Dryer

Operator Manual

The Safe Scrubbing Alternativer

Hygenic

Fully Cleanable Tanks

QA Controlst Supervisor Settings

North America / International

www.tennantco.com

Home Find... Go To..

9002326

Rev. 06 (11--2008)

*9002326*

OPERATION

This manual is furnished with each new model.

It provides necessary operation and maintenance instructions.

Read this manual completely and understand the machine before operating or servicing it.

A complete illustrated Parts Manual is also furnished with each new model. Use the Parts Manual to order replacement parts. To ensure prompt delivery, follow the “HOW TO ORDER PARTS” instructions printed in the Parts Manual.

This machine will provide excellent service. However, the best results will be obtained at minimum costs if:

The machine is operated with reasonable care.

The machine is maintained regularly - per the machine maintenance instructions provided.

The machine is maintained with manufacturer supplied or equivalent parts.

PROTECT THE ENVIRONMENT

Please dispose of packaging materials, old machine components such as batteries, hazardous fluids, including antifreeze and oil, in an environmentally safe way according to local waste disposal regulations.

Always remember to recycle.

MACHINE DATA

IMPORTANT: To ensure full warranty protection, fill out the attached MACHINE INSTALLATION / WARRANTY

REPORT REPLY CARD and return to Tennant within

30 days of purchase.

Please fill out at time of installation for future reference.

Model No. --

Serial No. --

Machine Options --

Sales Rep. --

Sales Rep. phone no. --

Customer Number --

Installation Date --

TENNANT Company

PO Box 1452

Minneapolis, MN 55440

Phone: (800) 553--8033 or (763) 513--2850

www.tennantco.com

FaSK--PAK and 1--STEP are US registered and unregistered trademarks of

Tennant Company.

Specifications and parts are subject to change without notice.

Home Find... Go To..

Tennant T5 (09--08)

OPERATION

TABLE OF CONTENTS

SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . .

SAFETY LABELS . . . . . . . . . . . . . . . . . . . . . . . . . . .

MACHINE COMPONENTS . . . . . . . . . . . . . . . . . . .

CONTROL PANEL COMPONENTS . . . . . . . . . . .

MACHINE INSTALLATION

UNCRATING MACHINE

. . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . .

INSTALLING BATTERIES . . . . . . . . . . . . . . . .

HOW THE MACHINE WORKS . . . . . . . . . . . . . . .

BRUSH AND PAD INFORMATION . . . . . . . . . . . .

MACHINE SETUP . . . . . . . . . . . . . . . . . . . . . . . . . .

ATTACHING SQUEEGEE ASSEMBLY . . . . .

INSTALLING BRUSHES iNSTALLING FaST--PAK

. . . . . . . . . . . . . . . . . .

CARTON (FaST Model) . . . . . . . . . . . . . . . . .

FILLING SOLUTION TANK . . . . . . . . . . . . . . .

MACHINE OPERATION . . . . . . . . . . . . . . . . . . . . .

PRE--OPERATION CHECKS . . . . . . . . . . . . . .

STARTING THE MACHINE

EMERGENCY STOPPING

. . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . .

WHILE OPERATING MACHINE . . . . . . . . . . .

BATTERY CHARGE LEVEL INDICATOR . . .

HOUR METER . . . . . . . . . . . . . . . . . . . . . . . . . .

OFF--AISLE WAND SETUP

AND OPERATION . . . . . . . . . . . . . . . . . . . . . .

DRAINING AND CLEANING TANKS

DRAINING RECOVERY TANK

. . . . . . . . . .

. . . . . . . . . . . .

DRAINING SOLUTION TANK . . . . . . . . . . . . .

CHARGING BATTERIES . . . . . . . . . . . . . . . . . . . .

BATTERY CHARGER SPECIFICATIONS: . .

ON--BOARD BATTERY CHARGER

SETTINGS: . . . . . . . . . . . . . . . . . . . . . . . . . . . .

USING THE ON--BOARD

BATTERY CHARGER . . . . . . . . . . . . . . . . . . .

ON--BOARD BATTERY

CHARGER ERROR CODES

ON--BOARD CHARGER

. . . . . . . . . . . . .

FUSE REPLACEMENT . . . . . . . . . . . . . . . . .

USING AN OFF--BOARD BATTERY

CHARGER (OPTION) . . . . . . . . . . . . . . . . . . .

ADJUSTING SCRUB HEAD BRUSHES

DISK MODEL

. . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . .

CYLINDRICAL BRUSH MODEL . . . . . . . . . . .

MACHINE MAINTENANCE

DAILY MAINTENANCE

. . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . .

MONTHLY MAINTENANCE . . . . . . . . . . . . . . .

BATTERY MAINTENANCE

SQUEEGEE BLADES

. . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . .

MOTOR MAINTENANCE . . . . . . . . . . . . . . . . .

FaST SYSTEM MAINTENANCE . . . . . . . . . . .

ec--H2O MODULE FLUSH PROCEDURE . . .

JACKING UP MACHINE . . . . . . . . . . . . . . . . . . . . .

TRANSPORTING MACHINE . . . . . . . . . . . . . . . . .

STORING MACHINE . . . . . . . . . . . . . . . . . . . . . . . .

FREEZE PROTECTION . . . . . . . . . . . . . . . . . .

RECOMMENDED STOCK ITEMS

TROUBLESHOOTING

. . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . .

CONTROL PANEL FAULT INDICATOR CODES 34

MACHINE SPECIFICATIONS . . . . . . . . . . . . . . . .

MACHINE DIMENSIONS . . . . . . . . . . . . . . . . . . . .

Tennant T5 (11--08)

Home Find... Go To..

OPERATION

SAFETY PRECAUTIONS

This machine is intended for industrial and commercial use. It is designed exclusively to scrub hard floors in an indoor environment and is not constructed for any other use. Only use recommended pads, brushes and commercially approved floor cleaners intended for machine application.

The following warning alert symbol and the “FOR

SAFETY” heading are used throughout this manual as indicated in their description:

WARNING: To warn of hazards or unsafe practices which could result in severe personal injury or death.

FOR SAFETY: To identify actions which must be followed for safe operation of equipment.

The following safety precautions signal potentially dangerous conditions to the operator or equipment. All operators must read, understand and practice them.

WARNING: Fire Or Explosion Hazard

-Never Use Flammable Liquids Or Operate

Machine In Or Near Flammable Liquids, Vapors

Or Combustible Dusts.

This machine is not equipped with explosion proof motors. The electric motors will spark upon start up and during operation which could cause a flash fire or explosion if machine is used in an area where flammable vapors/liquids or combustible dusts are present.

-Do Not Pick Up Flammable Materials Or

Reactive Metals.

-Batteries Emit Hydrogen Gas. Keep Sparks And

Open Flame Away. Keep Battery Compartment

Open When Charging.

WARNING: Electrical Hazard

-Disconnect Battery Cables and Charger Plug

Before Servicing Machine.

-Do Not Charge Batteries with Damaged Power

Supply Cord. Do Not Modify Plug.

If the charger supply cord is damaged or broken, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.

WARNING: Spinning Brush. Keep Hands

Away. Turn Off Power Before Working On Machine.

Home Find... Go To..

FOR SAFETY:

1. Do not operate machine:

-With flammable liquids or near flammable vapors as an explosion or flash fire may occur.

-Unless trained and authorized.

-Unless operator manual is read and understood.

-If not in proper operating condition.

2. Before starting machine:

-Make sure all safety devices are in place and operate properly.

3. When using machine:

-Go slow on inclines and slippery surfaces.

-Wear non--slip shoes.

-Reduce speed when turning.

-Report machine damage or faulty operation immediately.

-Never allow children to play on or around.

-Follow mixing and handling instructions on chemical containers.

-Do not operate on inclines that exceed 5%

(3°).

4. Before leaving or servicing machine:

-Stop on level surface.

-Turn off machine.

-Set parking brake, if equipped.

-Remove key.

5. When servicing machine:

-Avoid moving parts. Do not wear loose jackets, shirts, or sleeves.

-Disconnect battery cables and charger plug before working on machine.

-Wear protective gloves and eye protection when handling batteries or battery cables.

-Avoid contact with battery acid.

-Wear protective gloves and eye protection when handling white vinegar.

-Do not power spray or hose off machine.

Electrical malfunction may occur.

-Jack machine up at designated locations only (See JACKING UP MACHINE).

-Use hoist or jack that will support machine weight.

-Use manufacturer supplied or approved replacement parts.

-All repairs must be performed by a qualified service person.

-Do not modify the machine from its original design.

Tennant T5 (11--08)

6. When loading/unloading machine onto/off truck or trailer:

-Drain tanks before loading.

-Use a ramp that can support the machine weight and person loading it. Do not

exceed a 11° ramp incline at a ramp length

of 12 ft (3.7m).

SAFETY LABELS

OPERATION

-Turn machine off.

-Put scrub head in the lowered position.

-Block machine wheels.

-Use tie--down straps to secure machine.

-Set parking brake, if equipped.

The safety labels appear on the machine in the locations indicated. Replace labels if they are missing or become damaged or illegible.

WARNING LABEL --

Located on recovery tank cover.

Tennant T5 (06--06)

Home Find... Go To..

SPINNING BRUSH LABEL --

Located on scrub head

WARNING: Spinning Brush.

Keep Hands Away. Turn Off Power

Before Working On Machine.

BATTERY CHARGE LABEL --

Located on bottom side of recovery tank.

WARNING: Fire Or Explosion

Hazard. Batteries Emit Hydrogen

Gas. Keep Sparks And Open Flame

Away. Keep Battery Compartment

Open When Charging.

OPERATION

MACHINE COMPONENTS

1. Control Handle

2. Control Handle Start Bail

3. Upper & Lower Control Panels

4. Recovery Tank Drain Hose

5. On--board Battery Charger

6. Squeegee Lift Lever

7. Rear Fill-Port

8. Solution Tank Level/Drain Hose

9. Squeegee Vacuum hose

10. Wall Rollers

11. Squeegee Assembly

12. Solution Tank Clean-Out Port

13. Recovery Tank Support Stand

14. Control Board

15. Bucket Fill Port/Clean--out Port

16. FaST--PAK Carton Compartment (FaST Model)

ec--H2O System Module (ec--H2O Model)

17. Batteries

18. Off--Aisle Wand Solution Hose Coupler

19. Recovery Tank

20. Recovery Tank Cover

21. Cup Holder

22. Solution Tank

23. Disk Scrub Head

24. Pad Release Plunger

25. Pad Driver Window

26. Scrub Head Skirt

27. Parking Brake (option)

28. Cylindrical Brush Scrub Head

Home Find... Go To..

Tennant T5 (09--08)

OPERATION

CONTROL PANEL COMPONENTS

8 9

ec- H2O Model

1. Speed control knob

2. 1--STEP scrub button

3. Brush pressure increase button (+)

4. Brush pressure decrease button (--)

5. Solution flow increase button (+)

6. Solution flow decrease button (--)

7. Fault indicator -- Contact Service

8. Supervisor control indicator -- Lockout feature

9. Battery charge level indicator

10. Emergency stop button (option)

11. Off--Aisle wand on/off switch (option)

12. FaST system on/off switch (FaST model)

ec--H2O system on/off switch (ec--H2O model)

13. ec--H2O system indicator light (ec--H2O model)

14. Main power on/off key switch

15. Hour meter

Tennant T5 (09--08)

Home Find... Go To..

OPERATION

MACHINE INSTALLATION

UNCRATING MACHINE

1. Carefully check the shipping crate for signs of damage. Report damage at once to carrier.

2. Check the contents list. Contact distributor for missing items.

Contents:

4--6 V Batteries--Optional

3--Battery Cable Jumpers

Battery Tray

1--FaST--PAK 365 Concentrate--(FaST model)

Squeegee Assembly

2--Pad drivers (Disk Model)

2--Brushes (Cylindrical Brush Model)

3. To uncrate your machine, remove the shipping hardware and straps that secure the machine to the pallet. Carefully back machine down ramp.

ATTENTION: Do not roll machine off pallet unless a ramp is used, machine damage may occur.

ATTENTION: To prevent possible machine damage, install batteries after removing machine from shipping pallet.

INSTALLING BATTERIES

WARNING: Fire Or Explosion Hazard.

Batteries Emit Hydrogen Gas. Keep Sparks And

Open Flame Away. Keep Battery Hood Open When

Charging.

FOR SAFETY: When installing batteries, wear protective gloves and eye protection. Avoid contact with battery acid.

Battery Specifications:

Four 6 volt, 200A/20h or 235A/20h deep cycle batteries. Maximum battery dimensions:

7.5 in (190 mm) W x 10.8 in (275 mm) L x 11 in (284 mm) H.

1. Park the machine on a level surface, remove the key and set the parking brake.

2. Lift the recovery tank and remove the right side battery compartment panel (Figure 1). 13mm wrench required.

FIG. 1

3. Carefully install the batteries into the battery compartment tray (Figure 2). Arrange the battery posts as shown (Figure 3).

FIG. 2

4. Connect the battery cables to the battery posts as shown (Figure 3), RED TO POSITIVE (+) and

BLACK TO NEGATIVE (--).

BLACK

RED

200A/20H

235A/20H

Machine

Front

FIG. 3

IMPORTANT: If your machine is equipped with the on--board battery charger, make sure that the charger is properly set for your battery type before charging (See ON--BOARD CHARGER SETTINGS).

Home Find... Go To..

Tennant T5 (06--06)

HOW THE MACHINE WORKS

Conventional Scrubbing:

Water and detergent from the solution tank flow to the floor through a solution valve. The brushes use the detergent and water to scrub the floor clean. As the machine moves forward, the squeegee wipes the dirty solution from the floor into the recovery tank.

Foam Scrubbing (FaST Model):

(FaST--Foam activated Scrubbing Technology)

Unlike conventional scrubbing, the FaST system injects the FaST--PAK concentrate formula with a small amount of water and air onto the floor. The mixture creates a large volume of expanded wet foam for the brush to scrub the floor clean. As the machine moves forward, the foam collapses and the squeegee recovers the dirty solution into the recovery tank leaving the floor clean, dry and slip free.

ec- H2O Scrubbing (ec- H2O Model):

(ec--H2O--electrically converted water)

Normal water passes through a module where it is oxygenated and charged with an electric current. The electrically converted water changes into a blended acidic and alkaline solution forming a neutral pH cleaner. The converted water attacks the dirt, breaks it into smaller particles, and pulls it off the floor surface allowing the machine to easily scrub away the suspended soil. The converted water then returns to normal water in the recovery tank.

BRUSH AND PAD INFORMATION

For best cleaning results use the appropriate brush type for your cleaning application. Refer to the Parts manual for part number information.

Polypropylene Bristle Scrub Brush (Black) --

This general purpose polypropylene bristle scrub brush is used for scrubbing lightly compacted soilage. This brush works well for maintaining concrete, wood and grouted tile floors.

Soft Nylon Bristle Scrub Brush (White) --

Recommended for cleaning coated floors without removing finish. Cleans without scuffing.

Super Abrasive Bristle Scrub Brush (Gray) --

Nylon fiber impregnated with abrasive grit to remove stains and soilage. Strong action on any surface.

Performs well on buildup, grease, or tire marks.

Polishing Pad (White) --

Used to maintain highly polished or burnished floors.

OPERATION

Buffing Pad (Red) -- Used for light duty scrubbing without removing floor finish.

Scrubbing Pad (Blue) -- Used for medium to heavy--duty scrubbing. Removes dirt, spills, and scuffs and leaves surface clean ready for recoating.

Stripping Pad (Brown) -- Used for stripping of floor finish to prepare the floor for recoating.

Heavy Duty Stripping Pad (Black) -- Used for aggressive stripping of heavy finishes/sealers, or very heavy duty scrubbing.

MACHINE SETUP

ATTACHING SQUEEGEE ASSEMBLY

1. Park the machine on a level surface, remove the key and set the parking brake if equipped.

2. Lift the squeegee lift lever to the upward position

(Figure 4).

FIG. 4

3. Mount the squeegee assembly to the squeegee pivot bracket and secure with knobs (Figure 5).

FIG. 5

Tennant T5 (09--08)

Home Find... Go To..

OPERATION

4. Connect the vacuum hose to the squeegee assembly. Loop the hose as shown using the hose clip provided (Figure 6).

INSTALLING BRUSHES/PADS

FOR SAFETY: Before installing brushes or pad drivers, stop machine on level surface, remove key and set parking brake if equipped.

Disk Model:

1. Raise scrub head off the floor and remove key.

2. Attach the pad to the pad driver before installing the driver. Secure pad with centerlock (Figure 9).

FIG. 6

5. Check the squeegee blades for proper deflection.

The blades should deflect as shown (Figure 7).

FIG. 9

3. Align the pad driver under the motor hub and push it upward to engage (Figure 10).

FIG. 7

6. To adjust the blade deflection, place the squeegee assembly on a level surface and adjust the casters as shown (Figure 8).

2 mm

1/16”

FIG. 10

4. To remove the pad driver, raise the scrub head and push the pad release plunger downward

(Figure 11).

Lock Nut

FIG. 8

Home Find... Go To..

FIG. 11

Tennant T5 (09--08)

5. Check the scrub head to ensure that it is properly adjusted (See ADJUSTING SCRUB HEAD

BRUSHES).

Cylindrical Brush Model:

1. Raise scrub head off the floor and remove key.

2. Remove idler plate from scrub head by pressing the spring tab downward (Figure 12).

OPERATION

INSTALLING FaST--PAK CARTON (FaST Model)

ATTENTION: The FaST--PAK Concentrate Formula is specifically designed for the FaST system.

NEVER use a substitute. Machine damage may result.

1. Pull out the hose connector from the FaST--PAK carton and remove cap (Figure 14).

FIG. 12

3. Attach idler plate to the brush end that has the double row of bristles (Figure 13). Install brush.

Double row of bristles

FIG. 14

2. Open the battery compartment. Connect the

FaST--PAK carton to the supply hose and place carton in compartment (Figure 15). Make sure the

hose does not get pinched.

FIG. 13

4. Check the brushes to ensure they are properly adjusted (See ADJUSTING SCRUB HEAD

BRUSHES).

FIG. 15

3. When the supply hose is not in use, connect the storage plug to prevent the FaST system from drying out and clogging up the hose (Figure 16).

Tennant T5 (06--06)

Home Find... Go To..

FIG. 16

OPERATION

FILLING SOLUTION TANK

Using a hose or bucket, fill the solution tank to the

“MAX 85L” mark (Figure 17).

For Conventional Scrubbing: Use hot water

(140°F/60°C maximum). Pour a recommended cleaning detergent into the solution tank according to mixing instructions on the container.

For FaST or ec- H2O Scrubbing: Use cool clean water only (less than 70°F/21°C). Do not add any conventional floor cleaning detergents, system failure may result.

FIG. 17

ATTENTION: For Conventional Scrubbing, only use commercially approved cleaning detergents.

Machine damage due to improper detergent usage will void the manufacturer’s warranty.

WARNING: Fire or Explosion Hazard.

Never Use Flammable Liquids.

MACHINE OPERATION

FOR SAFETY: Do not operate machine, unless operator manual is read and understood.

WARNING: Fire Or Explosion Hazard. Never

Operate Machine In Or Near Flammable Liquids,

Vapors Or Combustible Dusts.

PRE--OPERATION CHECKS

Sweep area.

Check the battery charge level indicator.

Check the brushes/pads for wear.

Check the squeegee blades for wear and proper adjustment.

Make sure the recovery tank is empty and the float shut--off screen is installed and clean.

Check the scrub head skirt for wear.

For FaST Scrubbing: Check the FaST--PAK concentrate level.

For FaST or ec- H2O Scrubbing: Make sure the solution tank is filled with cool clean water only.

For FaST or ec- H2O Scrubbing: Ensure that all conventional cleaning agents are drained and rinsed from solution tank.

STARTING THE MACHINE

1. Release the parking brake if equipped (Figure 18).

2. Turn the key to the on ( I ) position (Figure 18).

Home Find... Go To..

FIG. 18

3. FaST Model: Press the FaST system switch to the on ( I ) position (Figure 19).

ec- H2O Model: Press the ec--H2O system switch to the on ( I ) position (Figure 19).

NOTE: The ec--H2O system indicator light will not turn on until the machine starts scrubbing.

Tennant T5 (03--08)

OPERATION

IMPORTANT: NEVER turn the FaST/ec--H2O system switch on when conventional scrubbing. Conventional cleaning detergents/restorers may cause failure to the

FaST/ec--H2O solution system. Drain, rinse and refill solution tank with cool clean water before operating the

FaST/ec--H2O system.

FIG. 19

4. Lower the squeegee assembly to floor by lowering the squeegee lift lever (Figure 20).

FIG. 22

7. Adjust the speed control knob to a desired scrubbing speed (Figure 23).

NOTE: 148--197 ft (45--60 meters) per minute is the recommended scrubbing speed.

FIG. 20

5. Press the 1--STEP scrub button (Figure 21).

FIG. 23

8. Press the brush pressure and solution flow buttons to increase (+) or decrease (--) as needed (Figure

24). To shut off the solution flow, continue to press the decrease button (--) until the lights turn off.

NOTE: For the FaST and ec--H2O models, the solution flow rate is fixed and requires no adjustment.

The ec--H2O module has optional flow rate settings. If solution flow adjustments are required, contact an

Authorized Service Center.

FIG. 21

6. Pull the control handle bail to start scrubbing

(Figure 22). To reverse the machine, simply push the control handle bail forward. Raise squeegee when reversing machine.

Tennant T5 (09--08)

Home Find... Go To..

FIG. 24

9. To stop scrubbing, release the control handle bail, press the 1--STEP scrub button and raise the squeegee.

OPERATION

EMERGENCY STOPPING

Strike the emergency stop button, if equipped, in the event of an emergency (Figure 25). This button shuts off all power to machine. Turn the button clockwise and restart the key to regain power.

ATTENTION: (ec- H2O model) Do not allow solution tank to run dry. ec- H2O module failure may result if operated without water for an extended period.

FIG. 25

WHILE OPERATING MACHINE

WARNING: Fire Or Explosion Hazard. Do Not

Pick Up Flammable Materials Or Reactive Metals.

1. Overlap each scrub path by 2 in (5 cm).

2. Keep the machine moving to prevent damage to floor finish.

3. Do not operate the machine on inclines that exceed

5% (3°).

4. Conventional scrubbing: Pour a commercially approved foam control solution into the recovery tank if excessive foam appears.

ATTENTION: Do not allow foam to enter the float shut-off screen, vacuum motor damage will result.

Foam will not activate the float shut-off screen.

5. For heavily soiled areas, use the double scrubbing method. First scrub the area with the squeegee up, let solution set for 3--5 minutes, then scrub the area a second time with squeegee down.

6. When leaving the machine unattended, remove the key and set the parking brake, if equipped.

7. If the machine detects a fault, the control panel lights will blink a fault code (See CONTROL

PANEL FAULT INDICATOR CODES).

8. ec- H2O Model: If an alarm sounds and the

ec--H2O system indicator light begins to blink red, the ec--H2O module must be flushed to resume

ec--H2O operation (See ec--H2O MODULE FLUSH

PROCEDURE) (Figure 26).

NOTE: When the alarm sounds and the light blinks red, the machine will bypass the ec--H2O system. To continue scrubbing, turn the ec--H2O switch off and change over to conventional scrubbing.

Home Find... Go To..

FIG. 26

ec- H2O SYSTEM

INDICATOR LIGHT CODE CONDITION

Solid green

Blinking red

Solid red

Normal operation

Flush ec--H2O module

Contact Service Center

BATTERY CHARGE LEVEL INDICATOR

The battery charge level indicator displays the charge level of the batteries (Figure 27). When the batteries are fully charged, all five indicator lights will glow. As the batteries discharge, the indicator lights will begin to go out from right to left.

When the discharge level reaches the red light, the operator will have approximately one minute to continue scrubbing. When the red light begins to flash the scrubbing functions will automatically shut off to alert the operator to recharge the batteries. By pressing the 1--STEP scrub button, when the red light is flashing, the operator will get an additional minute of scrubbing.

FIG. 27

Tennant T5 (09--08)

HOUR METER

The hour meter records the number of total hours the vacuum and brush motors have been powered on. Use the hour meter to determine when to perform recommended maintenance procedures and to record service history (Figure 28). See MACHINE

MAINTENANCE.

OPERATION

3. Using the hose adapter, connect the squeegee hose to the wand hose (Figure 30).

FIG. 30

4. Attach the off--aisle wand to the hoses (Figure 31).

FIG. 28

OFF--AISLE WAND SETUP AND OPERATION

If your machine is equipped with the off--aisle wand option, this allows you to scrub areas where the machine is unable to reach.

Preparing Machine for Off--Aisle Wand Scrubbing:

1. Park the machine on a level surface, turn key off and set parking brake if equipped.

2. Connect the solution hose to the coupler at the lower right side of machine (Figure 29).

FIG. 31

Operating the Off--Aisle Wand:

1. Turn the key and wand switch to the on ( I ) position (Figure 32). The FaST/ec--H2O system switch is disabled when operating the wand.

FIG. 29

Tennant T5 (09--08)

Home Find... Go To..

FIG. 32

OPERATION

2. Lower the squeegee to activate the vacuum motor

(Figure 33).

DRAINING AND CLEANING TANKS

After each use, the tanks should be drained and cleaned.

DRAINING RECOVERY TANK

1. Transport machine to disposal area and turn key switch off.

2. While holding the drain hose upward, remove the cap and lower hose to drain (Figure 35).

FIG. 33

3. Squeeze trigger to activate solution. Use brush for scrubbing and squeegee for pickup (Figure 34).

FIG. 35

3. After draining, open the recovery tank and clean out the tank (Figure 36).

FIG. 34

4. After scrubbing, turn off the wand switch and squeeze the trigger for five seconds to relieve the water pressure before disconnecting the solution hose.

WARNING: Fire or Explosion Hazard. Do Not

Pick Up Flammable Materials Or Reactive Metals.

FIG. 36

4. Clean the float shut-off screen and debris tray located in the recovery tank (Figure 37).

Home Find... Go To..

FIG. 37

Tennant T5 (09--08)

OPERATION

DRAINING SOLUTION TANK

1. To drain remaining water from the solution tank, pull the solution tank level hose off the hose fitting

(Figure 38).

FIG. 38

2. To rinse out the solution tank remove the clean--out cap at the rear of the machine and spray water directly into the clean-out ports (Figure 39).

FIG. 39

3. Clean the solution tank filter (Figure 40).

CHARGING BATTERIES

ATTENTION: To prolong the life of the batteries only recharge the batteries if the machine was used for a total of 30 minutes or more. Do not leave batteries discharged for lengthy periods.

WARNING: Fire Or Explosion Hazard.

Batteries Emit Hydrogen Gas. Keep Sparks And

Open Flame Away. Keep Battery Compartment

Open When Charging.

FOR SAFETY: When servicing batteries, wear protective gloves and eye protection when handling batteries and battery cables. Avoid contact with battery acid.

BATTERY CHARGER SPECIFICATIONS:

CHARGER TYPE:

-- FOR SEALED (Gel) BATTERIES

-- FOR WET (Lead acid) BATTERIES

OUTPUT VOLTAGE - 24 VOLTS

S OUTPUT CURRENT - 20 AMPS

S AUTOMATIC SHUTOFF CIRCUIT

FOR DEEP CYCLE BATTERY CHARGING

ON--BOARD BATTERY CHARGER SETTINGS:

If your machine is equipped with the on--board charger, the charger settings must be set for your battery type before charging. Failure to properly set will result in battery damage.

To determine your battery type, see battery label.

Contact your battery supplier if not specified.

To verify the setting of the charger, connect the charger cord into an electrical receptacle. The charger will display a sequence of codes. One of the codes will either read “GEL” or “Acd” (Figure 41).

GEL = Set for sealed/maintenance free batteries

Acd = Set for wet/lead acid batteries

FIG. 40

FIG. 41

Tennant T5 (06--06)

Home Find... Go To..

OPERATION

To change the setting, unplug the charger, peel up the corner of the display label and set the switches accordingly (Fig. 42). The charger cord must be unplugged when resetting.

NOTE: The machine will not operate when charging.

SEALED “GEL” BATTERY WET “Acd” BATTERY

FIG. 42

USING THE ON--BOARD BATTERY CHARGER

IMPORTANT: Before charging, make sure that the charger setting is properly set for your battery type

(See ON--BOARD CHARGER SETTINGS).

1. Transport the machine to a well--ventilated area.

2. Park the machine on a flat, dry surface. Turn the key off and set the parking brake, if equipped.

3. If charging wet (lead acid) batteries check the fluid level before charging (See BATTERY

MAINTENANCE).

4. Prop up the recovery tank for ventilation

(Figure 43).

FIG. 44

6. The charger will display a sequence of codes once the cord is connected (Figure 45).

Three--digits + the following code:

A = Charging current

U = Battery Voltage h = Charging time

C = Charging ampere--hours [Ah]

E = Energy used [Kwh]

“GEL” or “Acd” = Battery type the charger is currently set for. Before charging make sure your battery type matches the display:

GEL=Sealed, Acd=WET (lead acid). To change setting, see ON--BOARD CHARGER

SETTINGS.

Press the arrow button to review the codes.

FIG. 43

5. Connect the charger’s AC power supply cord into a properly grounded receptacle (Figure 44).

FIG. 45

7. Once the charging cycle begins, the indicator lights will progress from red, yellow to green. When the green indicator light comes on, the charging cycle is done. Unplug the charger cord.

If the charger detects a problem, the charger will display an error code (See ON--BOARD BATTERY

CHARGER ERROR CODES).

Home Find... Go To..

Tennant T5 (09--06)

OPERATION

ON--BOARD BATTERY CHARGER ERROR CODES

DISPLAY CODE

bat

E01

E02

E03

SCt

Srt

FAULT

Loose or damaged battery cable

Battery exceeded maximum voltage level.

Exceeded maximum battery voltage allowed.

No action necessary.

Safety thermostat exceeded maximum internal temperature.

Check if the charger vents are obstructed.

Exceeded maximum time for charging phase leaving the batteries undercharged due to a sulfated or faulty battery.

Safety timer exceeded maximum charging time. Interrupts charging cycle.

Repeat the charging cycle and if the error code E03 reappears check battery or replace it.

Replace battery.

Possible internal short circuit.

SOLUTION

Check battery cable connections.

No action necessary.

Contact Service Center.

Tennant T5 (06--07)

Home Find... Go To..

OPERATION

ON--BOARD CHARGER FUSE REPLACEMENT

The on--board charger is protected by a 15 Amp fuse.

To replace a blown fuse, follow the instructions as described below.

Required Fuse: 15 Amp (part no. 1030692).

Never substitute a higher Amp rated fuse than specified.

1. Unplug the charger’s AC power supply cord before replacing the fuse.

WARNING: Electrical Hazard, Unplug Charger

Plug Before Servicing Machine.

2. To access the on--board charger fuse, the machine’s left side panel must be removed.

To remove the side panel: a. Lift the recovery tank to access the side panel mounting screws. Make sure the tank is empty.

b. Remove the 3 mounting screws as shown

(Figure 46).

3 Mounting

Screws

FIG. 48

USING AN OFF--BOARD BATTERY CHARGER

(OPTION)

1. Transport the machine to a well--ventilated area.

2. Park the machine on a flat, dry surface. Turn the key off and set the parking brake, if equipped.

3. If charging wet (lead acid) batteries, check the fluid level before charging (See BATTERY

MAINTENANCE).

4. Prop up the recovery tank for ventilation

(Figure 49).

FIG. 46

c. Lower the recovery tank and pry out the top left edge of the panel to remove (Figure 47).

FIG. 49

5. Connect the charger’s AC power supply cord into a properly grounded receptacle.

6. Connect the charger’s DC cord into the machine’s battery receptacle (Figure 50).

FIG. 47

3. The fuse holder is located at the bottom of the charger. Use a screwdriver to access the fuse

(Figure 48).

Home Find... Go To..

FIG. 50

Tennant T5 (01--07)

OPERATION

7. The supplied charger will automatically begin charging and shut off when fully charged.

NOTE: The machine will not operate when charging.

ATTENTION: Do not disconnect the charger’s DC cord from the machine’s receptacle when the charger is operating. Arcing may result. If the charger must be interrupted during charging, disconnect the AC power supply cord first.

ADJUSTING SCRUB HEAD BRUSHES

To ensure optimum scrubbing performance periodically check the scrub head for proper adjustment.

FOR SAFETY: Before adjusting scrub head, stop machine on level surface, remove key and set parking brake if equipped.

DISK MODEL

Tools required: Measuring device, 1--1/16 in (27mm) wrench and 15/16 in (24mm) wrench

1. With brushes installed, lower the scrub head and apply medium brush pressure.

2. Turn machine off and remove key.

3. From the center front and back of scrub head, measure the distance from the top edge of scrub head to the floor (Figure 51).

Lock

Nut

FIG. 52

CYLINDRICAL BRUSH MODEL

After installing a new set of cylindrical brushes check the brush pattern to ensure proper brush adjustment.

Brushes that are not properly adjusted will result in premature wear and poor scrubbing performance

(Figure 53).

CORRECT BRUSH PATTERN

Even

Pattern

Uneven

Pattern

INCORRECT BRUSH PATTERNS

Tapered

Pattern

FIG. 53

To Inspect the Brush Pattern:

1. Position the machine on a dry dusty floor or apply a powdered substance, such as chalk.

2. Disconnect the drive motor wire connector to keep machine from moving forward (Figure 54).

FIG. 51

4. If scrub head is not level, loosen the lock nut and turn the scrub head leveling screw to level. Tighten down the lock nut once head is level (Figure 52).

FIG. 54

Tennant T5 (01--07)

Home Find... Go To..

OPERATION

3. Lower the scrub head to the floor and apply maximum brush pressure.

4. Shut off the solution flow.

5. Pull the control handle bail to create a brush pattern on the floor.

6. Raise the scrub head and pull the machine away.

7. Observe the brush pattern on floor. If the brush pattern is uneven or tapered, adjustment is required.

8. Reconnect drive motor wire.

To Adjust an Uneven Brush Pattern:

Tools required: Measuring device, 1--1/16 in (27mm) wrench and 15/16 in (24mm) wrench

1. Measure the distance from the front edge of the scrub head to the floor and from the back edge of the scrub head to the floor (Figure 55). The measurements should be the same.

To Adjust a Tapered Brush Pattern:

Tools required: 3/8 in (10mm) wrench and 6mm hex wrench

1. Raise the scrub head off floor and remove key.

2. Remove the idler plate from the brush (Figure 57).

FIG. 57

3. Hold the brush plug shaft with a wrench and loosen the 6mm hex screw (Figure 58).

FIG. 55

2. To level the scrub head, loosen the lock nut and turn the leveling screw clockwise to lower the rear of the scrub head or counter--clockwise to lower the front (Figure 56).

FIG. 58

4. To lower the brush end, turn the shaft clockwise for the front brush and counter--clockwise for the rear brush. Retighten hex screw (Figure 59).

FIG. 56

3. Recheck brush pattern.

NOTE: Replace brushes when worn to 5/8” (15mm).

FIG. 59

5. Recheck brush pattern.

NOTE: Replace brushes when worn to 5/8” (15mm).

Home Find... Go To..

Tennant T5 (01--07)

OPERATION

4. Remove the debris tray and empty (Figure 63)

MACHINE MAINTENANCE

To keep the machine in good working condition, it’s important that the following maintenance procedures are performed on a routine basis.

WARNING: Electrical Hazard. Disconnect

Battery Cables Before Servicing Machine.

DAILY MAINTENANCE (After Every Use)

1. Drain the recovery tank (Figure 60).

FIG. 63

5. Drain the solution tank (Figure 64).

FIG. 60

Rinse and clean out the recovery tank (Figure 61).

FIG. 64

6 Clean the solution tank filter (Figure 65).

FIG. 61

3. Remove the recovery tank float shut--off screen and clean (Figure 62).

FIG. 65

7. Rotate pad or replace when worn (Figure 66).

Tennant T5 (01--07)

FIG. 62

Home Find... Go To..

Disk Model

FIG. 66

OPERATION

8. Empty and rinse out the debris trough (Figure 67).

11. Wipe the squeegee blades clean (Figure 70). Store the squeegee assembly in the raised position to prevent blade damage.

Cylindrical Brush Model

FIG. 67

9. Inspect the cylindrical brushes for wear. Rotate brushes from front--to--rear every 50 hours (Figure

68). Replace when worn to a length of 5/8”

(15mm).

FIG. 70

12. Check the condition of the squeegee blade wiping edge (Figure 71). Rotate blade if worn (See

SQUEEGEE BLADES).

5/8”

(15mm)

Cylindrical

Brush Model

FIG. 68

10. Remove debris buildup from the underside of the cylindrical brush scrub head, including the idler plates and drive hubs (Figure 69).

FIG. 71

13. Clean the machine with an all purpose cleaner and damp cloth (Figure 72).

FOR SAFETY: When cleaning machine, do not power spray or hose off machine. Electrical malfunction may occur.

Cylindrical Brush Model

FIG. 69

FIG. 72

Home Find... Go To..

Tennant T5 (01--07)

14. Inspect the condition of the scrub head skirt, replace if worn or damaged (Figure 73).

OPERATION

MONTHLY MAINTENANCE

1. Periodically check the belt tension on the two brush motors. Tighten the belt if you’re able to twist it beyond 90_ at midpoint (Figure 76).

WARNING: Electrical Hazard. Disconnect

Battery Cables Before Servicing Machine.

Disk Model

Cylindrical Brush Model

FIG. 73

15. FaST Model: Connect the FaST--PAK supply hose to the storage plug when not in use (Figure 74).

Remove any dried concentrate from the hose connector by soaking it in warm water.

Cylindrical Brush Model

FIG. 76

2. Inspect and clean the recovery tank cover seal

(Figure 77). Replace if damaged.

FIG. 74

16. Clean wet/lead acid batteries to prevent corrosion and check for loose battery cable connections (See

BATTERY MAINTENANCE).

17. Recharge the batteries (Figure 75). To prolong the life of the batteries, only recharge the batteries if the machine was used for a total of 30 minutes or more.

FIG. 77

3. Lubricate all pivot points and rollers with a water resistant grease.

4. Lubricate the casters with a water resistant grease

(Figure 78).

FIG. 75

Tennant T5 (06--07)

Home Find... Go To..

FIG. 78

OPERATION

5. Clean the parking brake clamp with a cleaning solvent.

6. Check the machine for loose nuts and bolts.

7. Check the machine for leaks.

BATTERY MAINTENANCE (Wet/lead acid batteries)

1. Check battery fluid level frequently to prevent battery damage. The fluid should be at the level shown (Figure 79). Add distilled water if low. DO

NOT OVERFILL, the fluid may expand and overflow when charging.

CORRECT BATTERY FLUID LEVEL:

Before Charging

After Charging

FIG. 80

SQUEEGEE BLADES

When the blades become worn, simply rotate the blades end-for-end or top-to-bottom to a new wiping edge. Replace blades when all edges are worn.

The front blades on the 700mm/800mm squeegee assemblies have 12/14 slots on one edge and 6 slots on the opposite edge (Figure 81). If making sharp turns with the cylindrical brush models use the 12/14 slotted edge for maximum water pickup.

6 Slots on one edge

FIG. 79

WARNING: Fire Or Explosion Hazard.

Batteries Emit Hydrogen Gas. Keep Sparks And

Open Flame Away. Keep Battery Compartment

Open When Charging.

2. Clean the batteries to prevent battery corrosion.

Use a scrub brush with a mixture of baking soda and water (Figure 80).

FOR SAFETY: When cleaning batteries, wear protective gloves and eye protection. Avoid contact with battery acid.

12/14 Slots on opposite edge

FIG. 81

Replacing Squeegee Blades:

1. Loosen the band clamp and remove the band from the squeegee assembly (Figure 82).

FIG. 82

Home Find... Go To..

Tennant T5 (01--07)

2. Replace or rotate the rear blade to a new wiping edge and replace band (Figure 83).

OPERATION

FaST SYSTEM MAINTENANCE

Every 1000 hours replace the water filter and air filter located in the FaST detergent injector. Order filter kit p/n 9003009.

1. To access the detergent injector assembly, lower the scrub head and remove the front cover

(Figure 85).

FIG. 83

3. To change the front blade, remove the band and loosen the four knobs. Replace or rotate the front blade to a new wiping edge (Figure 84)

FIG. 85

2. Remove the injector assembly from clamps

(Figure 86).

FIG. 84

MOTOR MAINTENANCE

Contact an Authorized Service Center for carbon brush replacement.

Carbon Brush Replacement

Drive Transaxle Motor

Vacuum Motor

Disk Brush Motors

Cylindrical Brush Motors

Hours

750

1000

WARNING: Electrical Hazard. Disconnect

Battery Cables Before Servicing Machine.

FIG. 86

3. Replace the water and air filter. An 8mm hex wrench is required to install the new water filter (Figure 87).

Water Filter

(50 Mesh/Brown)

Air Filter

(50 Mesh/Brown)

FIG. 87

Tennant T5 (03--08)

Home Find... Go To..

OPERATION

ec- H2O MODULE FLUSH PROCEDURE

This procedure is only required when an alarm sounds and the ec--H2O system indicator light begins to blink red.

1. Drain the solution tank and recovery tank of all water.

2. Pour 1 gallon (4 liters) of white or rice vinegar into the solution tank at full strength. Do not dilute.

NOTE: Use white or rice vinegar only. The acidity level should be between 4--8%. Do not use other acids for this procedure.

FOR SAFETY: When servicing machine, wear protective gloves and eye protection when handling vinegar.

3. Disconnect the black connector fitting at the scrub head and place the hose into a bucket (Figure 88).

To access the connector fitting, you may have to remove the front cover from the machine.

5. Press and release the ec--H2O module flush switch to start the flush cycle (Figure 89). The module is located under the recovery tank.

NOTE: The module will automatically shut off when the flush cycle is complete (approx. 7 minutes). The module must run the full 7 minute cycle in order to reset the system indicator light and alarm.

Repeat flush procedure if the ec--H2O module does not reset. If module fails to reset, contact an

Authorized Service Center.

FIG. 88

4. Turn the key to the on ( I ) position.

FIG. 89

JACKING UP MACHINE

Use the designated locations to jack up the machine for service (Figure 90). Empty the recovery and solution tank and position the machine on a level before jacking.

FOR SAFETY: When servicing machine, jack machine up at designated locations only. Use jack or hoist that will support machine weight.

FIG. 90

Home Find... Go To..

Tennant T5 (11--08)

TRANSPORTING MACHINE

When transporting the machine by trailer or truck, be certain to follow the transporting procedure below:

1. Drain machine tanks.

2. Load the machine using a ramp that can support the machine weight and person loading it. The maximum ramp incline should not exceed 11° at a ramp length of 12 ft (3.7m).

3. Position the front of machine up against the front of the trailer or truck. Lower the scrub head and squeegee.

4. Set the parking brake, if equipped, and place a block behind each wheel to prevent the machine from rolling.

5. Secure with tie--down straps as shown (Figure 91).

It may be necessary to install tie-down brackets to trailer or truck.

FOR SAFETY: When loading/unloading machine onto/off truck or trailer, use a ramp that can support the machine weight and person loading it,

do not exceed a 11° ramp incline at a ramp length

of 12 ft (3.7m), use tie--down straps to secure machine and block machine wheels.

OPERATION

FREEZE PROTECTION

1. Drain the solution tank and recovery tank of all water.

2. Pour 1 gallon (4 liters) of recreational vehicle (RV) antifreeze into the solution tank at full strength.

Do not dilute.

FOR SAFETY: Avoid eye contact with antifreeze.

Wear safety glasses.

3. Turn the machine power on and operate the solution flow system. Turn the machine off when the red RV antifreeze is visible.

If your machine is equipped with the off--aisle wand option, operate the off--aisle wand for a few seconds to protect the pump.

Continue with the freeze protection procedure if machine is equipped with the FaST or ec--H2O system.

ec- H2O Model:

Press and release the flush switch on the ec--H2O module to cycle the antifreeze through ec--H2O system

(Figure 92). When the antifreeze is visible, press the switch again to turn off the module.

NEW PHOTOS

STORING MACHINE

FIG. 91

1. Charge the batteries before storing machine to prolong the life of the batteries.

2. Drain and rinse the tanks thoroughly.

3. Store the machine in a dry area with the squeegee and scrub head in the up position.

4. Open the recovery tank cover to promote air circulation.

ATTENTION: Do not expose machine to rain, store indoors.

5. If storing machine in freezing temperatures, follow the FREEZE PROTECTION instructions below.

Tennant T5 (09--08)

Home Find... Go To..

FIG. 92

IMPORTANT: Before operating machine, the antifreeze must be flushed from the module as described below.

If the antifreeze is not properly flushed from the

ec--H2O system, the ec--H2O module may detect an error and not function (ec--H2O switch indicator light will turn red). If this occurs, reset key and repeat the flush procedure as described below.

Flushing antifreeze from ec- H2O module:

1. Drain the antifreeze from the solution tank into a bucket.

2. Fill the solution tank with cool water until full (See

FILLING SOLUTION TANK).

OPERATION

3. Disconnect the black connector fitting at the scrub head and place the hose into a bucket (Figure 93).

To access the connector fitting, you may have to remove the front cover from the machine.

FIG. 93

4. Press and release the ec--H2O module switch to flush the antifreeze from the ec--H2O system

(Figure 92). The module is located under the recovery tank.

When the water turns clear, press the module switch again to stop the flush cycle.

Dispose the antifreeze in an environmentally safe way according to local waste disposal regulations.

5. The machine is now ready for scrubbing.

FaST Model:

The following items are required: valve coupling

#1002856 and 6 in (15 cm) hose #63182.

1. Remove the FaST--PAK carton and connect the valve coupling and 6 in (15 cm) hose to the FaST detergent supply hose (Figure 94).

FIG. 95

3. Pour the recreational vehicle (RV) antifreeze into the supply hose until full (Figure 96).

4. Keep the hose upright to prevent the antifreeze from spilling and lower the recovery tank.

FIG. 96

5. Operate the FaST system until the foaming stops.

This step could take anywhere from 5 to 10 minutes.

6. When finished, connect the supply hose to the storage plug (Figure 97).

FIG. 94

2. Disconnect the opposite end of the FaST supply hose from the injector assembly and drain the detergent from the hose (Figure 95). Reconnect the hose after draining. To access the injector assembly remove the front cover.

FIG. 97

10. To drain the antifreeze from the FaST supply hose, repeat steps 1 and 2.

Home Find... Go To..

Tennant T5 (09--08)

OPERATION

RECOMMENDED STOCK ITEMS

Refer to the Parts List Manual for recommended stock items. Stock Items are clearly identified with a bullet preceding the parts description. See example below:

TROUBLESHOOTING

PROBLEM CAUSE

Machine will not operate Discharged batteries

Emergency--stop button activated

Faulty battery(s)

Onboard battery charger will not operate

Loose battery cable

Faulty control board

Faulty key switch

Machine fault detected.

Plug not connected to power supply

Faulty charger fuse

Faulty power supply cord

Error detected.

Brush motor(s) will not operate

Machine will not propel

Vacuum motor will not operate

1--STEP scrub button is off

Brush motor overload

Discharged batteries

Faulty control board

Faulty scrub head (up/down) switch

Faulty control handle bail switch

Faulty brush motor or wiring

Worn carbon brushes

Broken or loose belt

(cylindrical brush model)

Parking brake is set

Machine fault detected

Faulty control board

Wheels raised off floor

Faulty transaxle motor or wiring

Worn carbon brushes

Exceeded maximum incline

Squeegee is raised off floor

SOLUTION

Charge batteries

Turn button clockwise to reset

Replace battery(s)

Tighten loose cable

Contact Service Center

See Contol Panel Fault Indicator Codes

Check plug connection

Replace charger fuse

Replace cord

See On--board Battery Charger Error Codes

Turn on the 1--STEP scrub button

See Control Panel Fault Indicator Codes

Charge batteries

Contact Service Center

Replace or tighten belt

Release parking brake lever

See Control Panel Fault Indicator Codes

Contact Service Center

Avoid steep inclines and reset key

Lower squeegee

Tennant T5 (11--08)

Home Find... Go To..

OPERATION

TROUBLESHOOTING -- Continued

PROBLEM

Vacuum motor will not operate

Little or no solution flow

Poor water pickup

Poor scrubbing performance

Reduced run time

Solution flow and brush pressure buttons and

FaST system switch are locked

CAUSE

Discharged batteries

Faulty control board

Faulty vacuum motor or wiring

Worn carbon brushes

Solution tank is empty

Clogged solution tank filter

Discharged batteries

Clogged solution valve

Faulty control board

Recovery tank is full or excessive foam buildup

Loose drain hose cap

Clogged float shut--off screen located in recovery tank

Clogged squeegee assembly

Worn squeegee blades

Incorrect Squeegee blade deflection

Loose vacuum hose connections

Clogged vacuum hose

Damaged vacuum hose

Recovery tank cover not in place

Damaged recovery tank cover seal

Faulty vacuum motor

Debris caught in brush

Worn brushes/pads

Incorrect brush pressure setting

Wrong brush/pad type.

Batteries not fully charged

Defective batteries

Batteries need maintenance

Faulty battery charger

Supervisor controls are activated (lockout feature)

SOLUTION

Charge batteries

Contact Service Center

Fill solution tank

Clean solution tank filter

Charge batteries

Remove valve and clean

Contact Service Center

Drain recovery tank

Tighten cap

Clean screen

Clean squeegee assembly

Replace or rotate squeegee blades

Adjust Squeegee blade height

Secure hose connections

Remove clogged debris

Replace vacuum hose

Properly position cover

Replace seal

Contact Service Center

Remove debris

Replace brushes/pads

Adjust pressure setting

Use correct brush/pad

Fully recharge batteries

Replace battery

See BATTERY MAINTENANCE

Repair or replace battery charger

Contact your Supervisor

Home Find... Go To..

Tennant T5 (06--06)

OPERATION

TROUBLESHOOTING -- Continued

PROBLEM

FaST Model: FaST

System does not operate or operate correctly

CAUSE

FaST system switch is not turned on

SOLUTION

Turn on FaST system switch

FaST--PAK supply hose not connected Connect supply hose

Clogged FaST--PAK supply hose or connectors

Soak in warm water to unclog

Empty FaST--PAK carton Replace FaST--PAK carton

Kink in FaST--PAK supply hose

Clogged FaST solution system

Faulty FaST system on/off switch

Faulty pump

Clogged solution tank filter

Undo hose kink

Contact Service Center

Drain solution tank. Remove solution tank filter, clean and reinstall

Clogged detergent orifice/filter screen

Clogged FaST solution inlet filter

Faulty control board

Mineral deposit build--up in module

Replace orifice/filter screen

(See FaST SYSTEM MAINTENANCE)

Contact Service Center

Flush module (See ec--H2O MODULE

FLUSH PROCEDURE)

ec- H2O Model:

ec--H2O system indicator light blinking red

ec- H2O Model:

Alarm Sounds

ec- H2O Model:

ec--H2O system indicator light solid red

ec- H2O Model:

ec--H2O system indicator light does not turn on

ec- H2O Model:

No water flow

Defective module

Defective light or module

Clogged module

Defective solution pump

Contact Service Center

Replace solution pump

Tennant T5 (09--08)

Home Find... Go To..

OPERATION

CONTROL PANEL FAULT INDICATOR CODES

The control panel fault indicator lights will display the following codes when the machine detects a fault.

Light #4

CODE

Light #1 blinks

Lights #1, #2 and #3 ripple

Lights #1 and #4 blink

Lights #3 and #4 blink

Lights #2 and #3 blink

Lights #1 and #3 blink

Light #2 blinks

Lights #1 and #2 blink

Light #3 blinks

Light #3 blinks when pressing the solution flow, brush pressure buttons and FaST system switch

Supervisor controls activated

(lockout feature)

Lights #1, #2 and #3 blink Wand Pump overload or malfunction.

All battery lights blink

All battery lights ripple

Light #1 Light #2

FAULT

Recovery tank is raised.

Battery charger connected.

Left Brush motor overload.

Right Brush motor overload.

Light #3

Propel motor overload.

Exceeded maximum incline.

Scrub head movement is obstructed or actuator motor malfunction.

Vacuum motor malfunction.

Propel throttle malfunction.

FaST pump overload or malfunction.

Emergency--Stop button activated

Key turned on while bail was engaged.

Battery Lights

SOLUTION

Lower recovery tank. Restart key to reset.

Disconnect battery charger. Restart key to reset.

Inspect brush for entangled debris, improper pad or contact service center.

Restart key to reset.

Inspect brush for entangled debris, improper pad or contact service center.

Restart key to reset.

Avoid steep inclines or contact service center. Restart key to reset.

Check scrub head for obstruction or contact service center. Restart key to reset.

Contact service center.

Reset the 10A circuit breaker or contact service center. Restart key to reset.

Contact your Supervisor.

Reset the 10A circuit breaker button or contact service center. Restart key to reset.

Turn button clockwise to reset.

Release the control handle start bail.

Home Find... Go To..

Tennant T5 (06--06)

OPERATION

MACHINE SPECIFICATIONS

MODEL

LENGTH

WIDTH

HEIGHT

MINIMUM AISLE TURN

WEIGHT

WEIGHT WITH BATTERIES

RECOVERY TANK CAPACITY

SOLUTION TANK CAPACITY

Disk,

600 mm

Disk,

700 mm

Disk,

800 mm

Cylindrical,

650 mm

Cylindrical,

800 mm

53 in / 1,346 mm

55.1 in / 1,400 mm 57.6 in / 1,463 mm 54.6 in / 1,387 mm 54.6 in / 1,387 mm

25.4 in / 645 mm 29 in / 737 mm 33 in / 838 mm 28 in / 711 mm 34 in / 864 mm

44 in / 1,120 mm

53 in / 1,346 mm 59 in / 1,499 mm 64 in / 1,626 mm 62 in / 1,575 mm

64.5 in / 1,638 mm

316 lb / 143 kg

580 lb / 263 kg

365 lb / 166 kg

609 lb / 276 kg

377 lb / 171 kg

621 lb / 282 kg

357 lb / 162 kg

621 lb / 282 kg

365 lb / 166 kg

629 lb / 285 kg

27 gal / 102 L

22.5 gal / 85 L

DRIVE SYSTEM

TRAVEL SPEED, MAXIMUM

Transaxle, 24 V, .25 hp / .19 kW

Cleaning: 220 ft / 67 m/min Transporting: 235 ft / 72 m/min

PRODUCTIVITY RATE

Theoretical

PRODUCTIVITY RATE

Estimated Actual

26,400 ft

2,450 m

2 h

17,875 ft

1,660 m

2 h

30,800 ft

2,860 m

2 h

20,800 ft

1,930 m

2 h

35,200 ft

3,270 m

2 h

24,000 ft

2,230 m

2 h

28,600 ft

2,660 m

2 h

19,200 ft

1,785 m

2 h

35,200 ft

3,270 m

2 h

24,000 ft

2,230 m

2 h

CLEANING PATH WIDTH

BRUSH DIAMETER

24 in / 600 mm 28 in / 700 mm 32 in / 800 mm 26 in / 650 mm 32 in / 800 mm

11.9 in / 302 mm 13.9 in / 353 mm 15.9 in / 404 mm 5.9 in / 151 mm 5.9 in / 151 mm

BRUSH PRESSURE

SOLUTION FLOW RATE -- Max: .45 gpm /

1.70 L/min

40 lb / 18 kg, 80 lb / 36 kg, 120 lb / 54 kg

.50 gpm /

1.90 L/min

.45 gpm /

1.70 L/min

.50 gpm /

1.90 L/min

SOLUTION FLOW RATE -- Med: .35 gpm /

1.30 L/min

SOLUTION FLOW RATE -- Low: .25 gpm /

.95 L/min

SQUEEGEE WIDTH

35.7 in / 908 mm standard

.40 gpm /

1.51 L/min

.30 gpm/

1.14 L/min

41.3 in / 1,051 mm standard

46.6 in / 1,185 mm standard

.35 gpm /

1.30 L/min

.25 gpm/

.95 L/min

41.3 in / 1,051 mm standard

.40 gpm /

1.51 L/min

.30 gpm /

1.14 L/min

46.6 in / 1,185 mm standard

31.5 in / 800 mm narrow aisle

35.7 in / 908 mm narrow aisle

41.3 in / 1,051 mm narrow aisle

35.7 in / 908 mm narrow aisle

41.3 in / 1,051 mm narrow aisle

BRUSH MOTOR

VACUUM MOTOR

WATER LIFT/AIR FLOW

BATTERIES

BATTERY CAPACITY

RUN TIME PER CHARGE*

ONBOARD CHARGER

TOTAL POWER CONSUMPTION

VOLTAGE DC

PROTECTION GRADE

DECIBEL RATING AT OPERA-

TOR’S EAR, INDOORS.**

VIBRATION AT CONTROLS

ACCELERATION RATE ON

OPERATOR -- MAX.

GRADE LEVEL, MAX.

Qty 2, .75 hp / .55 kW, 220 rpm, 24 V, 29 A Qty 2, .63 hp / .47 kW , 1,500 rpm,

24 V, 23 A

.85 hp / 640 W, 3--stage 5.7, 24 V, 26 A

62 in / 55 mm -- H

O 69 ft

/ 32.4 L

/min

Qty 4, 6 V

WET (lead Acid) = 235 Ah @ 20 h rate Sealed (Gel)= 200 Ah @ 20 h rate

WET = 5.5 h / Gel = 4.5 h

120VAC, 10 A, 50/60 Hz, 24VDC, 20 A output / 230VAC, 5 A, 50/60 Hz, 24VDC, 20 A output

50 Amp nominal

24 VDC

IPX3

<.39 ft/s

/ <.1188 m/s

67dB(A) 68dB(A)

<.34 ft/s

/ <.103 m/s

.56 ft/s

/ .179 m/s

Scrubbing 5% (3°), Transporting 8% (5°)

* Run times are based on Continuous Scrubbing Run Times.

** Sound pressure (ISO 11201) as recommended by the American Association of Cleaning Equipment Manufacturers (AACEM) and OSHA.

Tennant T5 (06--07)

Home Find... Go To..

OPERATION

FaST SYSTEM

PRODUCTIVITY RATE

Estimated Actual

SOLUTION PUMP

SOLUTION FLOW RATE

CONCENTRATE FLOW RATE

CONCENTRATE TO WATER

DILUTION RATIO

Disk,

600 mm

20,075 ft

1,865 m

2 h

Disk,

700 mm

22,750 ft

2,115 m

2 h

Disk,

800 mm

26,250 ft

2,440 m

2 h

Cylindrical,

650 mm

21,000 ft

1,950 m

2 h

Cylindrical,

800 mm

26,250 ft

2,440 m

2 h

24 Volt DC, 3.5 A, 1.5 gpm / 5.6L/min open flow, 60 psi / 4.13 bar bypass setting

0.15 gpm /

0.57 L/min

0.22 gpm / 0.83 L/min

0.15 gpm /

0.57 L/min

0.22 gpm /

0.83 L/min

0.0193 oz /

0.57 cc/min

0.028 oz / 0.83 cc/min

0.0193 oz /

0.57 cc/min

0.028 oz /

0.83 cc/min

1:1000

ec- H2O SYSTEM

PRODUCTIVITY RATE

Estimated Actual

SOLUTION PUMP

SOLUTION FLOW RATE *

Disk,

600 mm

20,075 ft

1,865 m

2 h

Disk,

700 mm

22,750 ft

2,115 m

2 h

Disk,

800 mm

26,250 ft

2,440 m

2 h

Cylindrical,

650 mm

21,000 ft

1,950 m

2 h

Cylindrical,

800 mm

26,250 ft

2,440 m

2 h

24 Volt DC, 3.5 A, 1.5 gpm / 5.6L/min open flow, 60 psi / 4.13 bar bypass setting

0.15 gpm /

0.57 L/min

(standard)

0.22 gpm / 0.83 L/min

(standard)

0.22 gpm /

0.83 L/min

(standard)

0.33 gpm /

1.25 L/min

(standard)

0.22 gpm /

0.83 L/min

(optional)

0.30 gpm /

1.14 L/min

(optional)

0.33 gpm / 1.25 L/min

(optional)

0.44 gpm / 1.67 L/min

(optional)

0.30 gpm /

1.14 L/min

(optional)

0.44 gpm /

1.67 L/min

(optional)

* If the optional solution flow rates are required, contact an Authorized Service Center.

Home Find... Go To..

Tennant T5 (09--08)

OPERATION

MACHINE DIMENSIONS

44.1 in /

1,120 mm

Models:

A =

B =

C =

600 mm

Disk

53 in / 1,346 mm

25.4 in / 645 mm

35.7 in / 908 mm

700 mm

Disk

800 mm

Disk

650 mm

Cylindrical

800 mm

Cylindrical

55.1 in / 1,400 mm 57.6 in / 1,463 mm 54.6 in / 1,387 mm 54.6 in / 1,387 mm

29 in / 737 mm 33 in / 838 mm 28 in / 711 mm 34 in / 864 mm

41.3 in / 1,051 mm 46.6 in / 1,185 mm 41.3 in / 1,051 mm 46.6 in / 1,185 mm

Tennant T5 (06--07)

Home Find... Go To..

Hello! I am an AI chatbot specifically trained to assist you with the Tennant T5 Scrubber-Dryer Operator Manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Show related prompts

Assistant typing

Assistant terminated