Thank you for purchasing a Young America Crib. Proper

Thank you for purchasing a Young America Crib. Proper
Built to Grow Crib Assembly Instructions
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY
Models:
BTG 2600 - Built to Grow Laurels Crib
BTG 2800 - Built to Grow Gala Crib
Thank you for purchasing a Young America Crib. Proper assembly will ensure
every effort has been made to design this crib with your baby's safety in mind. It is
certified to meet all safety guidelines established by ASTM International and the
CPSC-Consumer Product Safety Commission.
! 9#40+0): (#+.74'61(1..196*'5'9#40+0)5#0&6*'
#55'/$.;+05647%6+105%17.&4'57.6+05'4+175+0,74;14&'#6*
9JGPEJKNFKUCDNGVQRWNNVQCUVCPFKPIRQUKVKQPUGVVJGOCVVTGUUVQVJGNQYGUV
RQUKVKQPCPFTGOQXGDWORGTRCFUNCTIGVQ[UCPFQVJGTQDLGEVUVJCVEQWNFUGTXG
CUUVGRUHQTENKODKPIQWV
x 9JGPCEJKNFKUCDNGVQENKODQWVQTTGCEJGUVJGJGKIJVQHKP
EOVJGETKD
UJCNNPQNQPIGTDGWUGF
x &1016RNCEGCETKDPGCTCYKPFQYYJGTGEQTFUHTQODNKPFUQTFTCRGUOC[
UVTCPINGCEJKNF
x 6QTGFWEGVJGTKUMQH5+&5RGFKCVTKEKCPUTGEQOOGPFJGCNVJ[KPHCPVUDGRNCEGFQP
VJGKTDCEMUVQUNGGRWPNGUUQVJGTYKUGCFXKUGFD[[QWTRJ[UKEKCP
x 6QJGNRRTGXGPVUVTCPIWNCVKQPVKIJVGPCNNHCUVGPGTU#EJKNFECPVTCRRCTVUQHVJG
DQF[QTENQVJKPIQPNQQUGHCUVGPGTU
x 5VTKPIUECPECWUGUVTCPIWNCVKQP&QPQVRNCEGKVGOUYKVJCUVTKPICTQWPFC
EJKNFUPGEMUWEJCUJQQFUVTKPIUQTRCEKHKGTEQTFU&QPQVUWURGPFUVTKPIUQXGT
CETKDQTCVVCEJUVTKPIUVQVQ[U
x $GHQTGGCEJWUCIGQTCUUGODN[KPURGEVETKDHQTFCOCIGFJCTFYCTGNQQUGLQKPVU
OKUUKPIRCTVUQTUJCTRGFIGU&1016WUGETKDKHCP[RCTVUCTGOKUUKPIQTDTQMGP
%QPVCEV[QWTFGCNGTQTYTKVGVQ5VCPNG[(WTPKVWTG0QTVJ*COKNVQP5V0Q
*KIJ2QKPV0%HQTTGRNCEGOGPVRCTVUCPFKPUVTWEVKQPCNNKVGTCVWTGKHPGGFGF
x &1016UWDUVKVWVGRCTVU7UGQPN[DQNVUQTRCTVUUWRRNKGFD[OCPWHCEVWTGTQT
RCTVUQHEQORCTCDNGSWCNKV[CPFGSWCNFKOGPUKQPU&QPQVCNNQYGPFUQHDQNVUQT
UJCTRGFIGUVQDGGZRQUGF
x (QNNQYYCTPKPIUQPCNNRTQFWEVUKPCETKD
x +HTGHKPKUJKPIWUGCPQPÄVQZKEHKPKUJURGEKHKGFHQTEJKNFTGPžURTQFWEVU
x +PHCPVUECPUWHHQECVGQPUQHVDGFFKPI0GXGTCFFCRKNNQYEQOHQTVGTQTRCFFKPI
0GXGTRNCEGCFFKVKQPCNRCFFKPIWPFGTCPKPHCPV
x +PHCPVUECPUWHHQECVGKPICRUDGVYGGPETKDUKFGUCPFCOCVVTGUUVJCVKUVQQUOCNN
x 0GXGTWUGRNCUVKEUJKRRKPIDCIUQTQVJGTRNCUVKEHKNOCUOCVVTGUUEQXGTUDGECWUG
VJG[ECPECWUGUWHHQECVKQP
x &QPQVCNNQYEJKNFVQETCYNQTRNC[WPFGTPGCVJETKD
x 7UGECWVKQPYJGPCXCRQTK\GTKUKPWUG#NYC[UCKOVJGXCRQTUVGCOCYC[HTQO
VJGETKDCUYGNNCUCYC[HTQOCP[QVJGTYQQFHWTPKVWTGKVGO
x 6JGETKDOWUVDGHWNN[CUUGODNGFRTKQTVQWUG
x 4GCFCNNKPUVTWEVKQPUDGHQTGCUUGODNKPIETKD-''2+05647%6+105(14
(7674'75'
x
x
%#76+10
#P[OCVVTGUUWUGFKPVJKUETKDOWUVDGCVNGCUVÄ´
D[Ä´ YKVJCVJKEMPGUUQHPQNGUUVJCPKPEJGUCPFPQVGZEGGFKPIKPEJGU
9JGP%QPXGTVKPIVQC6QFFNGT$GF
x
x
0'8'4WUGDGFYKVJEJKNFTGPWPFGTOQPVJUQHCIG
6JGOCZKOWOYGKIJVQHVJGKPVGPFGFWUGTUJCNNPQVDGITGCVGTVJCPND
MI
2
Identifying the Parts
The crib illustrations in these instructions are generic in nature. The crib you have purchased
may not look like the ones illustrated; however, they all assemble in the same manner.
Mattress Platform
Left Crib End
Right Crib End
Footboard
Headboard
Alternate Foot and Block (BTG-2600 ONLY):
To be used when converting Crib to a Daybed
3
Identifying the Hardware
Identify the hardware included using the illustrations below
8 Connector Bolts
2 3/8” (1/4” x 20 thread)
4 Headboard Bolts
2” (1/4 x 20 thread)
2 Metal Locator Pins
3/8” diameter x 1 1/2” long
4 Mattress Brackets
with Bolts
2 Allen Wrenches
2 Hole Bolts (1” x 1/4” x 20 thread (For Headboard Only)
4 Hole Bolts (3/4” x 1/4” x 20 thread (For Footboard Only)
2 Caps (3/4” x 1/4” x 20 thread)
This hardware is for use when converting to a day bed and a full size bed.
4
Crib Assembly
NOTE: Read all instructions before assembling crib. KEEP INSTRUCTIONS FOR
FUTURE REFERENCE.
Attached to the mattress platform is a sleeve to store the instruction booklet.
After assembly is complete, return this instruction booklet to the sleeve for future
reference.
This crib conforms to the ASTM International and the CPSC-Consumer Product Safety
Commission guidelines for product safety. Please adhere to the guidelines in this booklet for assembly, use and maintenance.
Note the recommendations below:
x
x
x
x
x
x
x
x
Power tools are not recommended for assembly.
Give yourself plenty of room to work.
Due to the size of this bed, it must be assembled in the space it will occupy.
The assembly will take two people to complete.
Layout all the hardware and make sure that the proper length bolts are used in the
designated areas.
Do not substitute hardware. If an item is missing or damaged contact Stanley
Furniture Company immediately for replacement. Inspect all component parts and
hardware prior to beginning the assembly process.
Make sure all fasteners are tight.
Above all, take your time and read the instructions carefully.
Tools required for Assembly:
x
Allen Wrenches (provided)
This Crib is equipped with these additional features:
Bolt Retainer Sleeve—The Retainer Sleeves are located where Connector Bolts are used
to assemble the crib. It is designed to prevent loss of the Connector Bolts after crib is
disassembled. The Bolt Retainer Sleeves are permanently installed at the factory.
5
Attaching the Mattress Platform Brackets
x Make sure the brackets are straight and
Step 1:
x Locate the (4) Mattress Platform Brackets with
perpendicular to the crib uprights.
attached assembly bolts as shown in Fig. 1. De- x When child is able to pull to a standing
termine the high or low position of the mattress
position, set the mattress platform to the
foundation (Fig. 3) and attach the brackets on
lowest position and remove bumper pads,
both the left and right end section in the same
large toys and other objects that could
height location. (This is very important to keep
serve as steps for climbing out.
the foundation level and your child safe).
x Attach the (4) brackets and tighten bolts using
the wrench provided. See Figure 2.
See
Figure 2.
Figure 1. Left and Right
End Assemblies
Higher location
Figure 2.
Enlarged
View
Wrench
Lower location
Mattress
Bracket
Figure 3.
6
Attaching the End Sections
Step 2:
x Insert the (2) metal locator
pins in the lower hole of the
head board post as shown in
Fig 4a.
x Support the headboard and
attach one end section to the
See Figure 5.
headboard by aligning the
Insert bolts and
metal locator pin in the headtighten from back
of headboard
board with the bottom hole in
the end section. (make sure
the mattress platform brackets are to the inside of the
crib). See Fig 6.
x
Using (2) 2” headboard bolts
See Figure 4.
in the hardware pack, attach
Insert the locator pins
the bolts from the back of the
headboard and tighten with
the provided wrench. See
Fig 5.
x Repeat the process for the
remaining end section.
Figure 4a
Enlarged view
Locator Pin
Figure 5.
Enlarged view
End
Section
Back Side of
Headboard
2” Bolt
Figure 6.
Assembled ends
to headboard
Wrench
7
Attaching the Mattress Platform
Step 3:
x Place the mattress platform into the support
brackets. (Before inserting bolts, make
sure the instruction holder and the warning
label are facing up and readable as shown
in Fig 8.
x After the mattress platform is in place, use
the (4) 2 3/8” connector bolts to attach the
mattress platform to the support brackets.
Insert each bolt in place and loosely start
the bolt into the bracket threads.
See Fig 7.
x After all bolts have been set, securely
tighten each bolt with the provided wrench
to complete the mattress platform assembly.
x Fig 8. is how your crib should look with
Warning labels facing the front of the crib.
See Figure 7.
Figure 7.
Enlarged view of bolt attachment
Figure 8.
Assembled with mattress platform
8
Attaching the Footboard
Step 4:
x Align the footboard with the
end sections.
x Using (4) 2 3/8” connector
bolts, loosely attach the footboard as indicated in Fig 9.
x After the bolts have been attached, use the wrench provided to tighten each of the
bolts to secure the footboard.
See Figure 9.
Attach the footboard
Figure 9.
Enlarged view of
bolt attachment
Footboard
9
Final Step in Crib Assembly
Step 5: (The final and most important) Checklist.
x Inspect the crib once again to assure that all bolts are tight and that no hardware is missing. (if you
have missing hardware, contact Stanley Furniture immediately for replacement and do not use the
crib until the new hardware arrives).
x Do not place the crib near a window where the child may have access to window coverings, cords or
draperies as these articles pose a strangulation hazard.
x Replace the instructions in the holder provided. KEEP THE INSTRUCTIONS WITH THE CRIB.
x Install the crib mattress.
x Follow all the warnings on the use of this crib and all products in the crib.
x
CAUTION:
Any mattress used in this crib must be at least 27-1/4” by 51-5/8”
with a thickness of no less than 4 inches and not exceeding 6 inches.
10
Cleaning:
Mix together a mild solution of gentle dishwashing liquid and water, apply to the crib surface using a soft clean cloth lightly dampened in the solution. Rinse with clear water, using a lightly dampened, soft clean cloth, then dry all surfaces thoroughly with a dry cloth.
NO ABRASIVE CLEANERS, SCOURING PADS, STEEL WOOL OR COURSE RAGS
SHOULD BE USED TO CLEAN THIS FINE FURNITURE.
Storage:
A permanent storage pouch is attached to the mattress platform for the storage of the assembly instructions. After completing the assembly process, you are advised to read and
be aware of all WARNINGS, CAUTIONS, CLEANING, STORAGE, USE AND MAINTENANCE notices contained in these instructions. Do not place excess hardware in the
storage pouch as it could present a danger to a child if retrieved and could also damage
the mattress. When storing the crib, use CAUTION as temperature changes and humidity could be harmful to the crib. It is recommended that the crib be stored in a temperature controlled environment.
Periodic Maintenance:
1. Periodically check to make sure all bolts and connections are fastened securely.
2. If you are missing a part or need a replacement part, do not substitute parts. Ask your
dealer for replacement parts or contact Customer Service at (800) 659-7297.
3. The crib allows for 2 mattress heights. Move to the low position when the child can
pull up to a standing position. When the child reaches a height of 35” or can climb out
of the crib you should place the child in a youth or regular bed.
4. Save these instructions, in the sleeve attached to the mattress platform, in the event you
disassemble the crib and need to reassemble it. These instructions will also be useful
in identifying replacement parts if needed at a future date.
11
Lowering the Mattress Platform
Steps to lower the mattress:
x Remove the mattress from the crib
x Loosen the (4) bolts attaching the footboard and remove the footboard. See Figure 12.
x Loosen the (4) bolts attaching the Mattress Platform and remove the platform from the crib. Note the
bolts will stay with the Mattress Platform. See Figure 13.
x Remove the platform brackets and place in the lower position. See Figure 14.
x Follow Steps 3, 4 and 5 on Pages 8, 9, and 10 to reassemble the crib.
Figure 12.
Enlarged view
of Footboard
removal
Footboard
See Figure 12.
Figure 13.
Higher location
Figure 14.
Lower location
Wrench
Mattress bracket
12
Converting Your Crib to a Daybed
Steps to Convert Crib to a Daybed:
Step A:
x When converting to a Daybed the mattress must be in the lower position.
x Follow the instructions on page 12 for lowering the Mattress Platform. Do not reattach the footboard.
x (On the BTG-2800 - Gala Crib Model ONLY) The Feet and the Blocks from the Footboard must
be used as the Feet on the Crib Ends. Unscrew counter clock-wise and completely remove each Foot
from the Footboard. Gently grasp and pull each Foot Block to remove.
x Once the footboard has been removed and the Mattress Platform lowered the Alternate Foot and
Block must be attached to the Crib Ends. See Figure 15.
x Align the 1/4” Dowels in the Alternate Block with the holes in the bottom front of the Crib Ends.
See Figure 16.
x Attach the Alternate Feet by inserting the threaded bolt into the hole in the Alternate Block and
tighten securely to the Crib Ends. See Figure 17.
Holes in Bottom
Front of Crib Ends
1/4”
Dowels
Fig. 15 Daybed
Conversion with
Alternate Blocks
and Feet
Alt. Block
Fig. 16 Attaching Alternate Block
Alt. Block
Fig. 16
Attaching
Alternate Foot
Alt. Foot
13
Converting Your Crib to a Daybed
Steps to Convert Crib to a Daybed:
Step B:
x Remove the (4) Bolts located in the End Frames: Locate the (4)
2 3/8” Inch Bolts using the illustration below. For each bolt,
gently apply pressure to the exposed threaded end of Bolt. This
will engage the threads of the Bolt with the Retainer Sleeve.
With pressure being applied, insert the provided Allen Wrench
into the opposite end and turn counter-clockwise.
Fully assembled Daybed
Push to Gently
Apply pressure to
this end of Bolt.
Insert Allen
Wrench and
rotate counterclockwise.
View from back of Daybed
Step C:
x Install (4) 3/4” Inch Bolts into the countersink holes where the 2 3/8” Inch Bolts were removed in Step
B. Insert the 3/4” Inch Bolts into the countersink holes. Using the provided Allen Wrench while gently
applying pressure, turn the Bolt in a clockwise motion. As the Bolt threads engage into the Bolt Retainer
sleeve, gently tighten until the Bolt seats with the Retainer Sleeve (See illustrations below). Note: Do
not apply excessive force as the Bolt seats.
Installing Bolt
Bolt properly seated
14
Installed Bolt
Accessories and Options
Toddler Bed Conversion Kit item BTK-3230
is available as an option to convert the Built to
Grow Crib to a toddler or day bed. Contact your
Young America retailer, our Customer Service
Center, or website to purchase this item.
Safety Rails for a Full Size Bed item PSR-3268
are available for added safety when the bed is converted to a full size bed. Contact your Young
America retailer, our Customer Service Center, or
website to purchase this item.
Conversion to a Full Size Bed Kit BTF-3235 is
available. Instructions to convert the Built to Grow
crib are on the following page. Contact your Young
America retailer, our Customer Service Center, or
website to purchase this item.
15
Converting to a Full Size Bed
Step 1: Disassemble the crib or toddler/day bed.
x Using the wrench provided remove the components in the following order:
x Remove the footboard
x Remove the mattress platform
x Remove the crib ends from the crib headboard
x Keep and store all the hardware for future assembly of the crib. Store the crib components in a safe
dry place to prevent damage.
Step 2: Attach the side rails and slat roll.
x The side rails can be installed in two positions. The lower position, along with the purchase of
Safety Rails, is recommended for transition from the crib to a child’s first full size bed. The bed
side rails can be moved to the upper position after your child adapts to the transition. Under
bed storage options can be used with the bed rails positioned in the upper location. Contact your
Young America retailer or our Customer Service Center for further information.
x Install the rails into the headboard and foot board as shown and press down to lock into position.
x Remove (4) bolts from headboard. Note: The factory-installed Bolt Retainer Sleeve in the posts may
give resistance. The bolts require unthreading from back side of headboard.
x Insert (2) 1” connector bolts and 3/4” caps in the headboard and (4) 3/4” connector bolts in the footboard to cover the crib assembly holes. Tighten with the wrench provided. See Figure 15.
x Install the slat roll using the instructions provided with the slat roll for proper installation.
Headboard
Figure 15.
See Figure15.
See Figure 16.
Figure 15.
Figure 16.
Footboard
Slot in
Headboard
Hook
16
Stanley
Furniture
<RXQJ$PHULFD
Stanley Furniture Company
200 N HamiltonStUHHW
High Point, NC 27260
For TXHVWLRQVDQGparts, contact your ORFDO<RXQJ$PHULFDUHWDLOHURURXU
Customer Service &HQWHU 800659-7297Mon.-Fri. 8am-5pm6DWDPSP E67
ZZZ\RXQJDPHULFDFRP
18
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising