OPTIMUM metal working machines offer a maximum of quality, technically optimum solutions and convince by an outstanding price performance ratio. Continuous enhancements and product innovations guarantee state-of-the-art products and safety at any time.

Before commissioning the machine please thoroughly read these operating instructions and get familiar with the machine. Please also make sure that all persons operating the machine have read and understood the operating instructions beforehand.

Keep these operating instructions in a safe place nearby the machine.

Information

The operating instructions include indications for safety-relevant and proper installation, operation and maintenance of the machine. The continuous observance of all notes included in this manual guarantee the safety of persons and of the machine.

The manual determines the intended use of the machine and includes all necessary information for its economic operation as well as its long service life.

In the paragraph "Maintenance" all maintenance works and functional tests are described which the operator must perform in regular intervals.

The illustration and information included in the present manual can possibly deviate from the current state of construction of your machine. Being the manufacturer we are continuously seeking for improvements and renewal of the products. Therefore, changes might be performed without prior notice. The illustrations of the machine may be different from the illustrations in these instructions with regard to a few details. However, this does not have any influence on the operability of the machine.

Therefore, no claims may be derived from the indications and descriptions. Changes and errors are reserved!

Your suggestion with regard to these operating instructions are an important contribution to optimising our work which we offer to our customers. For any questions or suggestions for improvement, please do not hesitate to contact our service department.

If you have any further questions after reading these operating instructions and you are not able to solve your problem with a help of these operating instructions, please contact your specialised dealer or directly the company OPTIMUM.

Optimum Maschinen Germany GmbH

Dr.- Robert - Pfleger - Str. 26

D-96103 Hallstadt email: [email protected]

Internet: www.optimum-maschinen.com

Version 2.0.2 2014-11-04 Original operating instructions

B17Pro | B23Pro | B26Pro | B33Pro GB

Page 5

OPTIMUM

M A S C H I N E N - G E R M A N Y

1 Safety

Representation Conventions

 gives additional advices

 calls on you to act

 enumerations

This part of the operating instructions



 explains the meaning and use of the warning notices included in these operating instructions, defines the intended use of the drilling machine, points out the dangers that might arise for you or others if these instructions are not observed, informs you about how to avoid dangers.

In addition to these operation instructions, please observe



 the applicable laws and regulations, legal regulations for accident prevention, the prohibition, warning and mandatory signs as well as the warning labels on the drilling machine.

When installing, operating, maintaining and repairing the drilling machine it is necessary to observe the European standards.

If European standards are not applied at the national legislation of the country of destination, the specific applicable regulations of each country are to be observed.

If necessary, the required measures must be taken to comply with the specific regulations of each country before the drilling machine is used for the first time.

Always keep this documentation close to the drilling machine.

INFORMATION

If you are unable to solve a problem using these operating instructions, please contact us for advice:

Optimum Maschinen Germany GmbH

Dr. Robert-Pfleger-Str. 26

D- 96103 Hallstadt email: [email protected]

Page 6

B17Pro | B23Pro | B26Pro | B33Pro

Original operating instructions

Safety

Version 2.0.2 2014-11-04

Master Labels

Type plates

Säulenbohrmaschine

Upright drilling machine

Taladro

Perceuse

Trapano a colonna

Sloupová vrtačka

Søjleboremaskine

Pylväsporakone

Επιδαπεδειο Δραπανο

Asztali fúrógép

Boormachine

Wiertarki

Máquina de perfuração

SLO

Bormașină

Steberni vrtalni stroj

Sütunlu Matkap

Säulenbohrmaschine

Upright drilling machine

Taladro

Perceuse

Trapano a colonna

Sloupová vrtačka

Søjleboremaskine

Pylväsporakone

Επιδαπεδειο Δραπανο

Asztali fúrógép

SLO

Boormachine

Wiertarki

Máquina de perfuração

Bormașină

Steberni vrtalni stroj

Sütunlu Matkap

Tischbohrmaschine

Bench drilling machine

Taladro de sobremesa

Perceuse modèle établi

Trapani da banco

Stolní vrtačka

Table boremaskine

Penkkiporakone

ΔΡΑΠΑΝΟ ΠΑΓΚΟΥ

Asztali fúrógép

Boormachine tafelmodel

Wiertarki

Masina de gaurit

Bänkborrmaskin

Namizni vrtalni stroj

Sütunlu Matkap

Tischbohrmaschine

Bench drilling machine

Taladro de sobremesa

Perceuse modèle établi

Trapani da banco

Stolní vrtačka

Table boremaskine

Penkkiporakone

Επιτραπέζιο Δραπανο

Asztali fúrógép

Boormachine tafelmodel

Wiertarki

Engenho de Furarde Bancada

Masina de gaurit

Bänkborrmaskin

Namizni vrtalni stroj

Sütunlu Matkap

B 17 Pro

NO.

300 3171

Optimum Maschinen

Germany GmbH

Dr.-Robert-Pfleger-Str. 26

D-96103 Hallstadt

2520 U/min

500 W

230 V ~50 Hz

39 kg

Year

optimum-maschinen.de

Optimum Maschinen

Germany GmbH

Dr.-Robert-Pfleger-Str. 26

B 23 Pro Vario

D-96103 Hallstadt

NO.

301 1233

4940 U/min

750 W

400 V ~50 Hz

75 kg

Year

optimum-maschinen.de

Optimum Maschinen

Germany GmbH

Dr.-Robert-Pfleger-Str. 26

B 26 Pro Vario

D-96103 Hallstadt

NO.

301 1263

4000 U/min

750 W

400 V ~50 Hz

90 kg

optimum-maschinen.de

Year

Optimum Maschinen

Germany GmbH

Dr.-Robert-Pfleger-Str. 26

B 33 Pro Vario

D-96103 Hallstadt

NO.

301 1333

3850 U/min

1,5 kW

400 V ~50 Hz

140 kg

optimum-maschinen.de

Year

M A S C H I N E N - G E R M A N Y

Tischbohrmaschine

Bench drilling machine

Taladro de sobremesa

Perceuse modèle établi

Trapani da banco

Stolní vrtačka

Table boremaskine

Penkkiporakone

ΔΡΑΠΑΝΟ ΠΑΓΚΟΥ

Asztali fúrógép

Boormachine tafelmodel

Wiertarki

Engenho de Furarde Bancada

Masina de gaurit

Bänkborrmaskin

Namizni vrtalni stroj

Sütunlu Matkap

Säulenbohrmaschine

Upright drilling machine

Taladro

Perceuse

Trapano a colonna

Sloupová vrtačka

Søjleboremaskine

Pylväsporakone

Επιδαπεδειο Δραπανο

Asztali fúrógép

Boormachine

Wiertarki

Máquina de perfuração

SLO

Bormașină

Steberni vrtalni stroj

Sütunlu Matkap

Säulenbohrmaschine

Upright drilling machine

Taladro

Perceuse

Trapano a colonna

Sloupová vrtačka

Søjleboremaskine

Pylväsporakone

Επιδαπεδειο Δραπανο

Asztali fúrógép

Boormachine

Wiertarki

Máquina de perfuração

Bormașină

SLO

Steberni vrtalni stroj

Sütunlu Matkap

B 23 Pro

NO.

300 3231

750 W

230 V ~50 Hz

66 kg

Year

optimum-maschinen.de

B 26 Pro

NO.

300 3263

Optimum Maschinen

Germany GmbH

Dr.-Robert-Pfleger-Str. 26

D-96103 Hallstadt

2440 U/min

Optimum Maschinen

Germany GmbH

Dr.-Robert-Pfleger-Str. 26

D-96103 Hallstadt

2440 U/min

750 W

400 V ~50 Hz

82 kg

optimum-maschinen.de

Year

B 33 Pro

NO.

300 3333

Optimum Maschinen

Germany GmbH

Dr.-Robert-Pfleger-Str. 26

D-96103 Hallstadt

1810 U/min

1,1 kW

400 V ~50 Hz

135 kg

optimum-maschinen.de

Year

Safety

Version 2.0.2 2014-11-04 Original operating instructions

B17Pro | B23Pro | B26Pro | B33Pro GB

Page 7

OPTIMUM

M A S C H I N E N - G E R M A N Y

1.1 Safety instructions (warning notes)

1.1.1 Classification of hazards

We classify the safety instructions into different levels. The table below gives an overview of the classification of symbols (pictograms) and signal words for the specific danger and its (possible) consequences.

Pictogram Signal word

DANGER!

WARNING!

CAUTION!

ATTENTION!

Definition/Consequences

Imminent danger that will cause severe injury of death to the staff.

A danger that might cause severe injury to the staff or can lead to death.

Danger of unsafe procedure that might cause injury to the staff or property damages.

Situation that could cause damage to the drilling machine and products and other types of damage.

No risk of injury to the staff.

INFORMATION

Application tips and other important or useful information and notes.

No dangerous or harmful consequences for the staff or objects.

In case of specific dangers, we replace the pictogram by or general danger by a warning of injuries to hands, hazardous electrical voltage, rotating parts.

Page 8

B17Pro | B23Pro | B26Pro | B33Pro

Original operating instructions

Safety

Version 2.0.2 2014-11-04

OPTIMUM

M A S C H I N E N - G E R M A N Y

1.1.2 Other pictograms

Activation forbidden!

Disconnect the mains plug!

Use protective glasses!

Use ear protection!

Use protective gloves!

Use protective boots!

Use protective suit!

Protect the environment!

Contact address

1.2 Intended use

The drilling machine is designed and manufactured for holes in cold metals or other non flammable materials or that not constitute a health hazard using a rotating filing-stripping tool that has a number of grooves for collecting the filings.

The drilling machine may only be operated with tools whose cutting edge arrangement forms a force couple around the rotational axis in engagement.

A quick-action drill chuck for holding the tools is provided as standard. The drilling machine must only be used with a quick-action drill chuck.

If the drilling machine is used in any way other than described above, modified without the

Operations approval of the company Optimum Maschinen Germany GmbH then the drilling machine is being used improperly. not in accordance with

We will not be held liable for any damages resulting from any operation which is not in accordintended use!

ance with the intended use.

We expressly point out that the guarantee or CE conformity will expire due to any constructive technical or procedural changes which had not been performed by the company Optimum

Maschinen Germany GmbH.



It is also part of intended use that you observe the limits of the drilling machine,



"Technical data“ on page 19

the operating manual is observed, inspection and maintenance instructions are observed.

WARNING!

Extremely severe injuries.

It is forbidden to make any modifications or alternations to the operation values of the drilling machine! They could endanger the staff and cause damage to the drilling machine.

INFORMATION

The drilling machine B23Pro Vario, B26Pro Vario, B33Pro Vario is built according to the standard DIN EN 55011 class A.

WARNING!

The class A (machine tools) is not intended to be used in residential facilities, where the power is supplied via a public low voltage supply system. In these areas it may possibly

Safety

Version 2.0.2 2014-11-04 Original operating instructions

B17Pro | B23Pro | B26Pro | B33Pro GB

Page 9

OPTIMUM

M A S C H I N E N - G E R M A N Y be difficult to guarantee electromagnetic compatibility due to lead bound as well as emitted interferences.

ATTENTION!

If the drilling machine is not used as intended or if the safety directives or the operating instructions are ignored the liability of the manufacturer for any damages to persons or objects resulting hereof is excluded and the claim under guarantee is becoming null and avoid!

1.3 Reasonably foreseeable misuse

Any other use as the one determined under the "Intended use" or any use beyond the described use shall be deemed as not in conformity and is forbidden.

Any other use has to be discussed with the manufacturer.

It is only allowed to process metal, cold and non-inflammable materials with the drilling machine.

In order to avoid misuses it is necessary to read and understand the operating instructions before the first commissioning.

The operating staff has to be qualified.

1.3.1 Avoiding misuses



Use of suitable cutting tools.



Adapting the speed adjustment and feed to the material and workpiece.



Clamp workpieces firmly and vibration-free.

ATTENTION!

The workpiece is always to be fixed by a machine vice, jaw chuck or by another appropriate clamping tool such as for the clamping claws.

WARNING!

Risk of injury caused by workpieces flying off.

Clamp the workpiece in the machine vice. Make sure that the workpiece is firmly clamped in the machine vice resp. that the machine vice is firmly clamped on the machine table.



Use cooling and lubricating agents to increase the durability of the tool and to improve the surface quality.



Clamp the cutting tools and workpieces on clean clamping surfaces.



Sufficiently lubricate the machine.



Correctly adjust the bearing clearance and the guidings.

It is recommended:



Insert the drill in a way that it is exactly positioned between the three clamping jaws of the quick action chuck.

When drilling make sure, that

 the suitable speed is set depending on the diameter of the drill,

 the pressure must only be such that the drill can cut without load

 in case of too strong pressure the drill will get worn early or even might break resp. get jammed in the hole. If the drill gets jammed, immediately stop the main motor by pressing the emergency stop button.

 for hard materials, e.g. steel, use commercial cooling / lubricating agents,

 generally always drive the turning spindle out of the workpiece.

GB B17Pro | B23Pro | B26Pro | B33Pro

Page 10 Original operating instructions

Safety

Version 2.0.2 2014-11-04

OPTIMUM

M A S C H I N E N - G E R M A N Y

1.4 Possible dangers caused by the drilling machine

The drilling machine has undergone a safety inspection (analysis of danger with assessment of risks). It has been designed and built on the basis of this analysis using the latest technological advances.

Nevertheless, there is a residual risk as the drilling machine operates with



 at high speeds, rotating parts, with electrical voltages and currents.

We have used construction resources and safety techniques to minimize the health risk for the staff resulting from these hazards.

If the drilling machine is used and maintained by the staff who are not duly qualified, there may be a risk resulting from incorrect or unsuitable maintenance of the drilling machine.

INFORMATION

All staff involved in assembly, commissioning, operation and maintenance, must



 be duly qualified, strictly follow these operating instructions.

In the event of intended use



 there may be a risk to the staff, there may be a risk to the machine and other material values, the correct function of the drilling machine may be affected.

Disconnect the drilling machine whenever cleaning or maintenance work is being carried out.

WARNING!

The drilling machine may only be used with functional safety devices.

Disconnect the drilling machine immediately, whenever you detect a failure in the safety devices or when they are not fitted!



"Safety devices“ on page 13

All additional devices installed by the operator have to be equipped with the prescribed safety devices.

This is your responsibility being the operating company!

1.5 Qualification of the staff

1.5.1 Target group

This manual is addressed to



 the operating companies, the operators, the staff for maintenance works.

Therefore, the warning notes refer to both, operation and maintenance staff of the drilling machine.

Determine clearly and explicitly who will be responsible for the different activities on the machine (operation, maintenance and repair).

Unclear responsibilities constitute a safety risk!

Always disconnect plug of the drilling machine from the electrical power supply. This will prevent it from being used by unauthorized staff.

Operator

The operator is instructed by the operating company about the assigned tasks and possible risks in case of improper behaviour. Any tasks which need to be performed beyond the opera-

Safety

Version 2.0.2 2014-11-04 Original operating instructions

B17Pro | B23Pro | B26Pro | B33Pro GB

Page 11

OPTIMUM

M A S C H I N E N - G E R M A N Y

tion in the standard mode must only be performed by the operator if it is indicated in these instructions and if the operating company expressively commissioned the operator.

Electrical specialist

Due to his professional training, knowledge and experience as well as his knowledge of respective standards and regulations the electrical specialist is able to perform works on the electrical system and to recognise and avoid any possible dangers himself.

The electrical specialist is specially trained for the working environment in which he is working and knows the relevant standards and regulations.

Specialist staff

Due to its professional training, knowledge and experience as well as his knowledge of relevant regulations the specialist staff is able to perform the assigned tasks and to recognise and avoid any possible dangers himself.

Instructed persons

Instructed persons were instructed by the operating company about the assigned tasks and any possible risks in case of improper behaviour.

1.5.2 Authorized staff

WARNING!

Inappropriate operation and maintenance of the drilling machine constitutes a danger for the personnel, objects and the environment.

Only authorized staff may operate the drilling machine !

Persons authorized to operate and maintain should be trained technical staff and instructed by the ones who are working for the operating company and for the manufacturer.

The operating company must



 train the staff, instruct the staff in regular intervals (at least once a year) on

- all safety standards that apply to the machine,

- the operation,

- accredited technical guidelines, check staff‘s state of knowledge, document the trainings/instructions, require staff to confirm participation in training/instructions by means of a signature, check whether the staff is working safety- and risk-conscious and observe the operating instructions.

The operator must



 have obtained a training regarding the handling of the drilling machine, know the function and mode of action, before taking the machine in operation

- have read and understood the operating instructions,

- be familiar with all safety devices and instructions.

For work on the following parts there are additional requirements:



Electric components or operating materials: Must only be performed by a qualified electrician or person working under the instructions and supervision of a qualified electrician.

Obligations of the operating company

Obligations of the operator

Additional requirements regarding the qualification

GB B17Pro | B23Pro | B26Pro | B33Pro

Page 12 Original operating instructions

Safety

Version 2.0.2 2014-11-04

OPTIMUM

M A S C H I N E N - G E R M A N Y

Before starting work on electrical parts or operating agents, following measures are to be performed in the following order.

- Disconnect all poles.

- Secure against switching on.

- Check if the machine is zero potential.

1.6 Operator positions

The operator’s position is in front of the drilling machine.

INFORMATION

The mains plug of the drilling machine has to be freely accessible.

1.7 Safety measures during operation

CAUTION!

Risk by inhaling health hazardous dusts and fogs.

Depending on the materials which need to be treated and the agents which are used, dusts and fogs may be generated which endanger your health.

Make sure that the generated health hazardous dusts and fogs are safely sucked-off at the place of origin and that they are dissipated or filtered. To do so, use a suitable extraction unit.

CAUTION!

Risk of fire and explosion by using inflammable materials or cooling-lubricating agents.

Before processing inflammable materials (e.g. aluminium, magnesium) or using inflammable auxiliary materials (e.g. spirit) it is necessary to take additional preventive measures in order to safely avoid health risks.

1.8 Safety devices

Use the drilling machine only with properly functioning safety devices.

Stop the drilling machine immediately if there is a failure on the safety device or if it is not functioning for any reason.

It is your responsibility!

If a safety device has been activated or has failed, the drilling machine must only be used if you



 have removed the cause of the failure, have verified that there is no danger resulting for the staff or objects.

WARNING!

If you bypass, remove or deactivate a safety device in any other way, you are endangering yourself and other staff working with the drilling machine. The possible consequences are:



injuries may occur due to workpiece or parts of workpieces flying off,



contact with rotating parts, a fatal electrocution,

The drilling machine machine includes the following safety devices:



 an EMERGENCY STOP push button, a protective cover of the pulleys with positioning switch, a drill chuck protection with positioning switch, a drilling table with T-slots to fix the workpiece or a vice.

Safety

Version 2.0.2 2014-11-04 Original operating instructions

B17Pro | B23Pro | B26Pro | B33Pro GB

Page 13

OPTIMUM

M A S C H I N E N - G E R M A N Y

WARNING!

The separating protective covers which are made available and delivered together with the machine are designed to reduce the risk of workpieces or fragments of tools or workpieces flying off at high speed - however, this cannot be completely avoided.

Always work carefully and observe the limit values of your chipping process.

1.9 EMERGENCY-STOP push button

ATTENTION!

Also after actuating the EMERGENCY-

STOP switch, the drilling spindle is turning - depending on the previously selected speed - for a few seconds more.

EMERGENCY-

STOP button

Img.1-1: EMERGENCY-STOP push button

1.10 Separating protective devices

1.10.1 Covering cap of the pulley

A covering cap for the pulleys is mounted on the drilling head.

A switch is integrated in the protective cover which monitors that the closed position.

INFORMATION

You cannot start the machine if the protective cover is not closed.

Protective cover

1.10.2 Drill chuck protection

Adjust the protective equipment to the correct height before you start working.

To do so, detach the clamping screw, adjust the required height and re-tighten the clamping screw.

A switch is integrated in the fixture of the spindle protection which monitors that the cover is closed.

INFORMATION

You cannot start the machine if the drill chuck protection is not closed.

Drill chuck protection

Img.1-2: Protective cover

Img.1-3: Drill chuck protection

GB B17Pro | B23Pro | B26Pro | B33Pro

Page 14 Original operating instructions

Safety

Version 2.0.2 2014-11-04

OPTIMUM

M A S C H I N E N - G E R M A N Y

1.11 Drilling table

Seats for T-slots are attached to the drilling table.

WARNING!

Risk of injury due to parts flying off at high speed. Securely fix the workpiece on the drilling table.

Seats for clamping blocks

Img.1-4: Drilling table

1.12 Prohibition, warning and mandatory signs

INFORMATION

All warning signs must be legible. Check them regularly.

1.13 Safety check

Check the drilling machine at least once per shift. Inform the person responsible immediately of any damage, defect or change in operating function.

Check all safety devices



 at the beginning of each shift (at continuous operation), once a week (with the machine in operation), after every maintenance and repair work.

Check that prohibition, warning and information signs and the labels on the driling machine.



 are legible (clean them, if necessary), are complete.

INFORMATION

Use the following table for organizing the checks.

General check

Equipment

Protective cover

Signs,

Markings

Date:

Functional test

Equipment

EMERGENCY-STOP

Push button

Drill chuck protection

Date:

Safety

Version 2.0.2 2014-11-04

Check

Mounted and securely tightened

Installed and legible

Checked by (signature):

Check

After actuating an EMERGENCY STOP push button the drilling machine must be switched off.

Once the emergency stop button is activated, the bench drilling machine should be switched off. The drilling machine may not start if the drill chuck protection is open.

Checked by (signature):

Original operating instructions

B17Pro | B23Pro | B26Pro | B33Pro GB

Page 15

OPTIMUM

M A S C H I N E N - G E R M A N Y

Functional test

Equipment

Position switch

V-belt cover

Date:

Check

When the V-belt cover is opened, the drill must switch off automatically.

The drilling machine may not start if the V-belt cover is open.

Checked by (signature):

1.14 Individual protection gear

For certain work individual protection gear as protective equipment. This includes:



Safety helmet,

Protective goggles or face guard,

Protective gloves,

Safety shoes with steel toe caps,

Ear protection.

Before starting work, make sure that the prescribed individual protection gear is available in the workplace.

CAUTION!

Dirty or contaminated personnel protective equipment can cause diseases.

Clean your individual protection gear



after each use,



regularly, at least once a week.

Personal protective equipment for special works

Protect your face and eyes: wear a safety helmet with facial protection when performing works where your face and eyes are exposed to hazards.

Use protective gloves when handling pieces with sharp edges.

Use safety shoes when you assemble, disassemble or transport heavy components.

GB B17Pro | B23Pro | B26Pro | B33Pro

Page 16 Original operating instructions

Safety

Version 2.0.2 2014-11-04

OPTIMUM

M A S C H I N E N - G E R M A N Y

1.15 Safety during operation

We specially point out the specific dangers when working with and on the drilling machine.

WARNING!

Before switching on the drilling machine make sure that there are



no dangers generated for persons,



not cause damage to equipment.

Avoid any risky working practices:



Make sure your work does not endanger anyone.

The instructions mentioned in these operating instructions have to be strictly observed during assembly, operation, maintenance and repair.

Do not work on the drilling machine, if your concentration is reduced, for example, because you are taking medication.

Observe the accident prevention regulations issued by your Employers Liability Insurance

Association or other competent supervisory authority, responsible for your company.

Inform the supervisor about all endangerments or errors.

Use the prescribed personnel protective equipment. Make sure to wear a well-fitting work suit and, if necessary, a hairnet.

Do not use protective gloves when drilling or milling.

1.16 Safety during maintenance

Inform the operators in good time about any maintenance and repair works.

Report

Report all safety relevant changes and performance details of the drilling machine or their operational behavior. Document all changes, have the operating instructions updated accordingly ment these and train machine operators.

changes and docu-

1.16.1 Disconnecting and securing the drilling machine

Unplug the main switch before starting any maintenance or repair work. All machine components and hazardous voltages and movements must have been disconnected.

Attach a warning sign on the machine.

1.16.2 Using lifting equipment

WARNING!

The use of unstable lifting and load suspension gear that might break under load can cause severe injuries or even death.

Check that the lifting and load suspension gear devices



they have sufficient load carrying



and that it is in perfect condition.

Observe the accident prevention regulations issued by your Employers Liability

Insurance Association or other competent supervisory authority, responsible for your company.

Fasten the loads properly.

Never walk under suspended loads!

Safety

Version 2.0.2 2014-11-04 Original operating instructions

B17Pro | B23Pro | B26Pro | B33Pro GB

Page 17

OPTIMUM

M A S C H I N E N - G E R M A N Y

1.16.3 Mechanical maintenance work

Remove or install protection safety devices before starting any maintenance work and re-install them once the work has been completed.This includes:



Covers,

Safety indications and warning signs,

Earth (ground) connections.

If you remove protective or safety devices, re-fit them immediately after the completing the work.

Check if they are working properly!

1.17 Accident report

Inform your superiors and Optimum Maschinen Germany GmbH immediately in the event of accidents, possible sources of danger and any actions which almost led to an accident (near misses).

There are many possible causes for "near misses".

The sooner they are notified, the faster the causes can be eliminated.

INFORMATION

We point out the specific dangers when performing works with and on the drilling machine when describing such works.

1.18 Electrical system



"Maintenance“ on page 43

Have the machine and/or the electric equipment checked regularly. Check the electrical system according to DIN EN 60204.

Immediately eliminate all defects such as loose connections, defective wires, etc.

A second person must be present during work on live components to disconnect the power in the event of an emergency.

Immediately disconnect the drilling machine if there are any anomalies in the power supply!

GB B17Pro | B23Pro | B26Pro | B33Pro

Page 18 Original operating instructions

Safety

Version 2.0.2 2014-11-04

OPTIMUM

M A S C H I N E N - G E R M A N Y

2 Technical data

The following information are the dimensions and indications of weight and the manufacturer‘s approved machine data.

B17Pro B23Pro

B23Pro

Vario

2.1 Electrical connection

230V~50 Hz

230V~50 Hz or

400V~50 Hz

B26Pro

Vario

B33Pro

Vario

400V~50 Hz 400V~50 Hz 400V~50 Hz 400V~50 Hz 400V~50 Hz

2.2 Power drive motor

500 W 750 W 750 W 750 W

2.3 Drilling capacity in steel S235JR

16mm 25mm 25mm 25mm

750 W

25mm

2.4 Continuous drilling capacity in steel S235JR

12mm 20mm 20mm 20mm 20mm

1.1 KW

30mm

25mm

1.5 KW

30mm

25mm

2.5 Spindle seat

MK2 MK2

2.6 T-slots - size

12mm 12mm

2.7 Table size

230 x

220mm

280 x

245mm

2.8 Spindle stroke

MK2

12mm

280 x

245mm

MK3

14mm

330 x

290mm

MK3

14mm

330 x

290mm

MK4

14mm

475 x

425mm

MK4

14mm

475 x

425mm

65mm 80mm

2.9 Throat depth

152mm 180mm

2.10 Machine height

80mm

180mm

860mm 1012mm

2.11 Column diameter

1010mm

Ø 60mm Ø 73mm Ø 73mm

2.12 Distance spindle - table

85mm

210mm

1670mm

Ø 80mm

85mm

210mm

1670mm

Ø 80mm

120mm

254mm

1720mm

Ø 92mm

120mm

254mm

1720mm

Ø 92mm max. 325mm max. 425mm max. 425mm max. 720mm max. 720mm max. 695mm max. 695mm

2.13 Distance spindle - stand

max.

530mm max.

618mm

2.14 Dimension

max.

610mm max.

1230mm max.

1180mm max.

1180mm

Technical data

Version 2.0.2 2014-11-04 Original operating instructions

B17Pro | B23Pro | B26Pro | B33Pro GB

Page 19

OPTIMUM

M A S C H I N E N - G E R M A N Y

B17Pro

600 x 260 x

860 mm

B23Pro

654 x 330 x

1012 mm

B23Pro

Vario

660 x 320 x

1010 mm

2.15 Weight of machine [kg]

B26Pro

700 x 350 x

1670 mm

B26Pro

Vario

710 x 350 x

1670 mm

39 66

2.16 Spindle speeds

75 82 90



"Speed tables“ on page 33

Speed steps

5 12

12 infinitely variable

2.17 Environmental conditions temperature

12 infinitely variable

5 - 35 °C

Relative humidity

25 - 80 %

B33Pro

860 x 480 x

1720 mm

B33Pro

Vario

870 x 480 x

1720 mm

135

140

9 infinitely variable

2.18 Emissions

The emission of the drilling machine is 73 dB(A) at idle.

If the is installed in an area where various machines are in operation the acoustic influence immission) on the operator of the drilling machine may exceed 85 dB(A).

INFORMATION

This numerical value was measured on a new machine under proper operating conditions.

Depending on the age respectively on the wear of the machine it is possible that the noise behaviour of the machine changes.

Furthermore, the factor of the noise emission is also depending on manufacturing influencing factors, e.g. speed, material and clamping conditions.

INFORMATION

The mentioned numerical value is the emission level and not necessarily a safe working level.

Though there is a dependency between the degree of the noise emission and the degree of the noise disturbance it is not possible to use it reliably to determine if further precaution measures are required or not.

The following factors influence the actual degree of the noise exposure of the operator:



Characteristics of the working area, e.g. size or damping behaviour,

Other noise sources, e.g. the number of machines,

Other processes taking place in the proximity and the period of time during which the operator is exposed to the noise.

Furthermore, it is possible that the admissible exposure level might be different from country to country due to national regulations.

This information about the noise emission shall allow the operator of the machine to more easily evaluate the endangering and risks.

CAUTION!

Depending on the overall noise exposure and the basic limit values the machine operators has to wear an appropriate hearing protection.

GB B17Pro | B23Pro | B26Pro | B33Pro

Page 20 Original operating instructions

Technical data

Version 2.0.2 2014-11-04

OPTIMUM

M A S C H I N E N - G E R M A N Y

We generally recommend to use a noise protection and a hearing protection.

Technical data

Version 2.0.2 2014-11-04 Original operating instructions

B17Pro | B23Pro | B26Pro | B33Pro GB

Page 21

OPTIMUM

M A S C H I N E N - G E R M A N Y

3 Assembly

INFORMATION

The drilling machine comes disassembled due to packaging reasons.

Before commissioning, the drilling machine has to be assembled.

3.1 Scope of delivery



When the machine is delivered, check immediately that the drilling machine has not been damaged during transport and that all components are included. Remove all parts from the cardboard box and compare them with the following list.

Drill head

Drilling table

Base

Upright component (table support pre-assembled)

RÖHM quick-action drill chuck

Clamping lever

Crank handle

Levers for spindle sleeve feed

Operating manual

3.2 Transport



Centres of gravity



Load suspension point

(marking the positions for the

attachment position gear)



Prescribed transportation position

(Marking of the top surface)



Means of transport to be used



Weights

WARNING!

Severe or fatal injuries may occur if parts of the machine tumble or fall down from the forklift truck or from the transport vehicle. Follow the instructions and information on the transport case.

WARNING!

The use of unstable lifting and load suspension gear that might break under load can cause severe injuries or even death.

Check that the lifting and load suspension gear has sufficient load capacity and that it is in perfect condition. Observe the accident prevention regulations issued by your

Employers Liability Insurance Association or other competent supervisory authority, responsible for your company.

Fasten the loads properly. Never walk under suspended loads!

GB B17Pro | B23Pro | B26Pro | B33Pro

Page 22 Original operating instructions

Assembly

Version 2.0.2 2014-11-04

OPTIMUM

M A S C H I N E N - G E R M A N Y

3.3 Storage

ATTENTION!

In case of wrong and improper storage electrical and mechanical machine components might get damaged and destroyed.

Store packed and unpacked parts only under the intended environmental conditions.

Follow the instructions and information on the transport case:



Fragile goods

(Goods require careful handling)



Protect against moisture and humid environment



"Environmental conditions temperature“ on page 20



Prescribed position of the packing case

(Marking of the top surface - arrows pointing to the top)



Maximum stacking height

Example:not stackable - do not stack a second packing case on top of the first one.

Consult Optimum Maschinen Germany GmbH if the machine and accessories are stored for more than three months or are stored under different environmental conditions than those given here.

3.4 Installation and assembly

3.4.1 Requirements to the installation site

Organize the working area around the drilling machine according to the local safety regulations.

INFORMATION

In order to attain good functionality and a high processing accuracy as well as a long durability of the machine the installation site should fulfil certain criteria.

Please observe the following points:



The device must only be installed and operated in a dry and well-ventilated place.

Avoid places nearby machines generating chips or dust.

The installation site must be free from vibrations also at a distance of presses, planing machines, etc.

The substructure must be suitable for the drilling machine. Also make sure that the floor has sufficient load bearing capacity and is level.

The substructure must be prepared in a way that possibly used coolant cannot penetrate into the floor.

Assembly

Version 2.0.2 2014-11-04 Original operating instructions

B17Pro | B23Pro | B26Pro | B33Pro GB

Page 23

OPTIMUM

M A S C H I N E N - G E R M A N Y



Any parts sticking out such as stops, handles, etc. have to be secured by measures taken by the customer if necessary in order to avoid endangerment of persons.

Provide sufficient space for the staff preparing and operating the machine and transporting the material.

Also consider that the machine is accessible for setting and maintenance works.

Provide for sufficient illumination (Minimum value: 500 lux, measured at the tool tip). At little intensity of illumination an additional illumination has to be ensured e.g. by means of a separate workplace lamp.

INFORMATION

The mains plug of the drilling machine has to be freely accessible.

3.4.2 Assembly

WARNING!

Danger of crushing when assembling and installing the machine components.



"Qualification of the staff“ on page 11

The drilling machine must be installed by at least 2 people, because various elements and individual parts have to be sustained and joined during assembly.

INFORMATION



The following description of the assembly refers to the B26Pro drilling machine. It has been chosen for description of the following operations because of its close similarity with the drilling machines.

B17Pro

B23Pro

B33Pro

Mounting of base and drill column



Position the base on the floor and attach the column to the base. Fastening screws for the drilling pillar have been provided on the base.



Loosen the screw on the retaining ring and remove the retaining ring and toothed rack.

Screw

Retaining ring

Toothed rack

Drill column

Base

Img.3-1: Assembly of the base

GB B17Pro | B23Pro | B26Pro | B33Pro

Page 24 Original operating instructions

Assembly

Version 2.0.2 2014-11-04

Mounting of the drilling table support



Position the worm gear in the support of the drilling table.



Adjust the toothed rack within the drilling table support in a way that the teeth of the toothed rack cam into the spiral wheel of the support for the drilling table support .

Toothed rack

Clamping lever

Drilling table support

OPTIMUM

M A S C H I N E N - G E R M A N Y

Img.3-2: Mounting of the drilling table support

INFORMATION

The longer untoothed end of the rack must point upward.



Push the drilling table support with the toothed rack on the drill column.



Push the supporting ring onto the upright and the rack.



Tighten the screw of the supporting ring slightly. Make sure that the drilling table support still can be easily turned around the upright.



Attach the clamping lever for drilling table fastening.

Fitting the drill head



Place the drill head on the drill upright and turn it until it is aligned with the base. Immobilise the drill head with the two headless screws in the drill head over the toothed rack.



Screw in the 3 levers of the spindle sleeve feed and attach the crank of the table height adjustment.

Drill head

Lever

Spindle sleeve lever

Drill upright

Img.3-3: B26Pro



Insert the drilling table in the drilling table support and clamp it with the clamping lever.

Drilling table

Clamping lever

Img.3-4: B26Pro

Fitting the quick-action drill chuck



"Assembly quick- action drill chuck“ on page 38

Assembly

Version 2.0.2 2014-11-04 Original operating instructions

B17Pro | B23Pro | B26Pro | B33Pro GB

Page 25

OPTIMUM

M A S C H I N E N - G E R M A N Y

Assembly of the drill chuck protection

WARNING!

Never operate drilling machines without drill chuck protection.

1. Shift the aluminium profile including the mounted safety screen (plastic screen) into the fixture which is mounted on the drilling head.

2. After assembly of the aluminium profile screw down the setting screw.

Fixture

Setting screw

Aluminium profile including mounted safety screen

3. Screw the hexagon socket screw with the locking washer into the aluminium profile.

WARNING!

Make sure that the hexagon socket screw and the locking washer are mounted and tightly screwed. Otherwise the aluminium profile would slide out of the fixture when the setting screw is screwed off.

Hexagon socket screw

Locking washer

Aluminium profile

Img.3-5: Assembly-1

Img.3-6: Assembly-2

4. Make sure that the setting screw shows to the front after assemblyand if the drill chuck protection isclosed.

Setting screw

INFORMATION

A switch is integrated in the fixture of the drill chuck protection which monitors the closed position. It is not possible to start the machine until the drill chuck protection is closed.

Img.3-7: Assembly-3

GB B17Pro | B23Pro | B26Pro | B33Pro

Page 26 Original operating instructions

Assembly

Version 2.0.2 2014-11-04

OPTIMUM

M A S C H I N E N - G E R M A N Y

3.5 Installation

Check the horizontal orientation of the base of the drilling machine with a spirit level.

Fix the foot of the drilling machine to the substructure with the provided through-holes.

The installation site must be designed in accordance with ergonomic workplace requirements.

ATTENTION!

Tighten the setscrews on the drilling machine only until it is firmly secured and can neither move during operation nor be turned over.

If the setscrews are too tight and the base is uneven, the stand of the drilling machine may break.

3.5.1 Fixing

In order to provide for the necessary stability of the bench drill machine and the upright drilling machine it is necessary to firmly bolt the base of the machine to the subsurface.

We recommend you to use shear connector cartridges resp. heavy-duty anchors.



Fix the foot of the drilling machine to the substructure with the provided throughholes.

The Through-bore are marked with arrows on the machine base.

Through-bore

Arrow sign

ATTENTION!

Tighten the fixing screws of the drilling machine only as much that it is safely fixed and cannot break away or tilt over.

If the fixing screws are too tight in particular in connection with an uneven substructure it may result in a broken stand.

Through-bore

Arrow sign

Img.3-8: Marking of the fixing points of the bench drill machines

Img.3-9: Marking of the fixing points of the upright drilling machines

Assembly

Version 2.0.2 2014-11-04 Original operating instructions

B17Pro | B23Pro | B26Pro | B33Pro GB

Page 27

OPTIMUM

M A S C H I N E N - G E R M A N Y

B23Pro, B23Pro Vario

Img.3-10: Fixing of foot B23Pro

B26Pro, B26Pro Vario

Img.3-11: Fixing of foot B26Pro

GB B17Pro | B23Pro | B26Pro | B33Pro

Page 28 Original operating instructions

Assembly

Version 2.0.2 2014-11-04

B33Pro, B33Pro Vario

OPTIMUM

M A S C H I N E N - G E R M A N Y

Img.3-12: Fixing of foot B33Pro

3.6 First commissioning

ATTENTION!

Before commissioning the machine check all screws, fixtures resp. safety devices and tighten up the screws if necessary!

WARNING!

Risk by using improper workpiece clamping materials or by operating the machine with inadmissible speed.

Only use the clamping materials (e.g. drill chuck) which had been delivered togetherwith the machine or as optional equipment offered by OPTIMUM.

Use the working clamping materials only in the provided admissible speed range.

Workpiece clamping materials must only be modified according to the recommendations of OPTIMUM or of the clamping material manufacturer.

WARNING!

When first commissioning the drilling machine by inexperienced staff you endanger people, the machine and the equipment.

We do not take any liability for damages caused by incorrectly performed commissioning.

Power supply



Connect the electrical supply cable.



Check the fusing (fuse) of your electrical supply according to the technical data.

Assembly

Version 2.0.2 2014-11-04 Original operating instructions

B17Pro | B23Pro | B26Pro | B33Pro GB

Page 29

OPTIMUM

M A S C H I N E N - G E R M A N Y

3.6.1 Warming up the machine

ATTENTION!

If the drilling machine and in particular the drilling spindle is immediately operated at maximum load when it is cold it may result in damages.

If the machine is cold such as e.g. directly after having transported the machine it should be warmed up at a spindle speed of only 500 1/min for the first 30 minutes.

3.7 Drilling machines with frequency converter

CAUTION!

Frequency converter have a high frequency leakage current which is discharged through the protective conductor. Frequency converter must not be operated with a CEE plug.

Connect the machine firmly to a junction box. (see EN 50178 /VDE 5.2.11.1) . If the machine can not be connected firmly on a junction box, the earth connection must not be passed over the plug.

INFORMATION

The frequency converter (drive regulator) might release the Fl protected switch of your electrical supply. In order to avoid malfunction, you either need an Fl protected switch sensitive for pulse current or AC/DC sensitive. In case of malfunction or release of the FI protected switch, please check the installed type. We recommend you to use an FI protected switch sensitive to AC/DC.

FI protected switches sensitive to AC/DC (RCCB), type B are adequate for 1-phase and 3phase fed frequency converters (driving regulator). An FI protected switch type AC (only for alternating current) is not appropriate for frequency converters. FI protected switches type AC are no longer used.



"Electrical connection“ on page 19,



"Qualification of the staff“ on page 11

ATTENTION!

For 400V machines: Imperatively make sure that all 3 phases ( L1, L2, L3) are correctly connected.

Most motor defects result of wrong connections. For instance if a motor phase is not correctly clamped or connected to the neutral conductor (N).

Effects may be as follows:



The motor is getting hot very rapidly.



Increased motor noises.



The motor has no power.

ATTENTION!

Check if the drive motor is turning in the correct rotation direction. If the rotational direction switch is switched to the position to perform clockwise rotations (R) the spindle needs to rotate clockwise. If necessary, exchange two phase connections.

If your connector plug is equipped with a phase inverter, this is done by turning it by

180°.

The guarantee will become null and void if the machine is wrongly connected.

GB B17Pro | B23Pro | B26Pro | B33Pro

Page 30 Original operating instructions

Assembly

Version 2.0.2 2014-11-04

4 Operation

4.1 Control and indicating elements

OPTIMUM

M A S C H I N E N - G E R M A N Y

Img.4-1: B23Pro Vario

Pos.

Designation

1 Push button "OFF“

EMERGENCY-STOP button

Clamping lever

Quick-action drill chuck

Handle for V-belt tension

Drilling table

Potentiometer for speed regulation

(only on Vario machines)

Operation

Version 2.0.2 2014-11-04

Pos.

Designation

2 Push button "ON“

Switch for the turning direction

(only on 400V machines)

Scale of drill depth stop

Protective cover of V-belt housing

Lever for spindle sleeve feed

Table height adjustment

Frequency converter

(only on Vario machines)

Original operating instructions

B17Pro | B23Pro | B26Pro | B33Pro GB

Page 31

OPTIMUM

M A S C H I N E N - G E R M A N Y

4.2 Safety

Use the drilling machine only under the following conditions:



The drilling machine is in proper working order.

The drilling machine is used as prescribed.

The operating manual is followed.

All safety devices are installed and activated.

All failures should be eliminated immediately. Stop the machine immediately in the event of any abnormality in operation and make sure it cannot be started-up accidentally or without authorisation. Notify the person responsible immediately of any modification.

4.2.1 Drill depth stop

When drilling several holes of the same depth you can use the drill depth stop.



Loosen the locking screw and turn the graduated collar until the required drilling depth matches with the indicator.



Re-tighten the locking screw.

Locking screw

Drill depth stop

Scale

The spindle can now only be lowered to the set depth.

4.2.2 Inclination table

The drilling table can be inclined to the right or to the left.



Loosen the fixing screw.



Pull out the threaded pin.

Fixing screw

Threaded pin

Scale

Img.4-2: Scale of drill depth stop

Img.4-3: Fixing screw

INFORMATION

If you can not pull out the threaded pin, so the seat can be solved by turning at the nut clockwise.



Set the desired angle using the scale.



Re-tighten the fixing screw again.

INFORMATION

The threaded pin is only provided for correct positioning of a horizontal level of the drilling table.

GB B17Pro | B23Pro | B26Pro | B33Pro

Page 32 Original operating instructions

Operation

Version 2.0.2 2014-11-04

OPTIMUM

M A S C H I N E N - G E R M A N Y

4.3 Speed change

Set the required speed within the range of

15 to 225% using the potentiometer (only on Vario machines). If the required speed is not available, you must change the position of the V-belts.



Disconnect the machine from the electrical supply.



Remove the screw fittings on the protective cover of the V-belts.

Protective cover

V-belt

Sliding rail screws

Handle

Img.4-4: Belt drive



Open the protective cover.



Loosen the sliding rail screws on the right and left side of the drill head and shift the motor towards the quick-action drill chuck using the handle.

WARNING!

Do not open the cover hood until the drilling machine is disconnected from the electrical supply.

Close and screw the cover hood after every speed change.

ATTENTION!

Watch for the proper tension of V-belts.

Too heavy or too low tension of the belt can cause damage. cm.

4.3.1 Speed tables

B17Pro

2520

1900

1400

900

500

8 x 825 mm (Li)

Item No. 030 0317 1108

Operation

Version 2.0.2 2014-11-04 Original operating instructions

B17Pro | B23Pro | B26Pro | B33Pro GB

Page 33

Master Labels

OPTIMUM

M A S C H I N E N - G E R M A N Y

B23Pro

V13 x 650 mm

Item No. 09V13650

440

290

200

890

480

330

1480

1040

530

2440

1770

1180

Master Labels

B23Pro Vario

Spindel

Spindle

313

160

105

500

362

168

V13 x 650 mm

Item No. 09V13650

mittlere Keilriemenscheibe

~ 15 % 100 % ~ 225 % centre pulleys

140

100

440

290

200

965

695

450

890

480

330

1480

1040

530

2200

1125

735

3480

2520

1174

Motor

700

590

415

2440

1770

1180

4940

4090

2880

GB B17Pro | B23Pro | B26Pro | B33Pro

Page 34 Original operating instructions

Operation

Version 2.0.2 2014-11-04

B26Pro

Master Labels

V13 x 735 mm

Item No. 039V13735

Master Labels

B26Pro Vario

1480

1040

530

2440

1770

1180

440

290

200

890

480

330

Spindel

Spindle

V13 x 735 mm

Item No. 039V13735

mittlere Keilriemenscheibe

~ 15 % 100 % ~ 225 % centre pulleys

140

100

440

290

200

965

695

450

Motor

313

160

105

500

362

168

890

480

330

1450

1125

735

1480

1040

530

3000

2520

1174

700

590

415

2440

1770

1180

4000

3200

2150

OPTIMUM

M A S C H I N E N - G E R M A N Y

Operation

Version 2.0.2 2014-11-04 Original operating instructions

B17Pro | B23Pro | B26Pro | B33Pro GB

Page 35

M A S C H I N E N - G E R M A N Y

B33Pro

V13 x 860 mm

Item No. 0300333301

Master Labels

B33Pro Vario

360

250

120

940

440

210

1810

1260

400

Spindel

Spindle

V13 x 860 mm

Item No. 0300333301

mittlere Keilriemenscheibe

centre pulleys

~ 15 % 100 % ~ 225 %

130

360

250

120

910

600

300

Motor

310

145

550

400

130

940

440

210

1810

1260

400

2150

1020

520

3850

2800

930

GB B17Pro | B23Pro | B26Pro | B33Pro

Page 36 Original operating instructions

Operation

Version 2.0.2 2014-11-04

OPTIMUM

M A S C H I N E N - G E R M A N Y

4.4 Standard values for speeds with HSS – Eco – twist drilling

Cooling

Material

Steel, unalloyed, up to 600 N/mm

Structural steel, alloyed, quenched and subsequently drawn, up to 900N/mm2

Structural steel, alloyed, quenched and subsequently drawn, up to 1200 N/mm2

Stainless steels up to 900 N/ mm2 e.g. X5CrNi18 10

Cutter diameter n f n f" n

1) f

2) n f

2 3 4 5 6 7 8 9 10

5600 3550 2800 2240 2000 1600 1400 1250 1120

0.04

0.063

0.08

0.10

0.125 0.125

0.16

0.20

3150 2000 1600 1250 1000 900 800 710 630

0.032

0.05

0.063

0.08

0.10

0.125 0.125

0.16

2500 1600 1250 1000 800 710 630 560 500

0.032

0.04

0.05

0.063

0.08

0.10

0.125 0.125

2000 1250 1000 800 630 500 500 400 400

0.032

0.05

0.063

0.08

0.10

0.125 0.125

0.16

1): Speed [ n ] in r/min

2): Feed [ f ] in mm/r

3): Cooling: E = Emulsion; oil = cutting oil

E/oil

Oil



The above mentioned indications are standard values. In some cases it may be advantageous to increase or decrease these values.

When drilling a cooling or lubricating agent should be used.

For stainless materials (e.g. VA – or NIRO steel sheets) do not center as the material would compact and the drill bit will become rapidly blunt.

The workpieces need to be tensed inflexibly and stably (vice, screw clamp).

4.5 Switching on the machine

The drilling machine is switched on in the following order.



Turn the change-over switch into the neutral position (0).



Push the green push-button, and wait two seconds.



Turn the change-over switch into the desired direction of rotation. The rotation of spindle starts.

4.6 Switching off the machine



Push the red push-button, or turn the change over switch into the neutral position (0).

4.7 Quick-action drill chuck

The bench drilling machine is equipped with a RÖHM quick-action drill chuck.

In order to clamp a drill bit, hold the upper part of the quick-action drill chuck and turn the lower part.

Drill sleeve

Drill drift

Upper part of quickaction drill chuck

Lower part of quickaction drill chuck

Img.4-5: Quick action - drill chuck

ATTENTION!

Make sure that the clamped tool is firmly and correctly fitted.

Operation

Version 2.0.2 2014-11-04 Original operating instructions

B17Pro | B23Pro | B26Pro | B33Pro GB

Page 37

OPTIMUM

M A S C H I N E N - G E R M A N Y

4.7.1 Disassembly quick- action drill chuck

The quick-action drill chuck and the taper mandrel are released from the drilling spindle with the aid a drill drift.

WARNING!

Do not unfit the quick-action drill chuck until the drilling machine has been disconnected from the power supply.



Disconnect the drilling machine from electrical power supply.



Move the drill sleeve down.



Turn the drilling spindle so that the opening at the drilling spindle sleeve coincides with the opening at the drilling spindle.



Loosen the taper mandrel of the quick-action drill chuck with the help of a drill drift.

4.7.2 Assembly quick- action drill chuck

The quick-action drill chuck is secured through a form-fit union (pulling heel) against twisting in the drilling spindle.

A friction-locking union holds and centres the quick-action drill chuck with the taper mandrel in the drilling spindle.

Drill sleeve

Opening for the drill drift

Drilling spindle driver

Taper mandrel

Img.4-6: Taper mandrel



Check and, if necessary, clean the conical seat in the drilling spindle and at the taper mandrel of the tool or the quick-action drill chuck.



Press the taper mandrel into the drilling spindle.

4.8 Cooling

The friction generated during rotation can cause the edge of the tool to become very hot.

The tool should be cooled during the drilling process. Cooling the tool with a suitable cooling lubricant ensures better working results and a longer edge life of the tools. This is best realised by a separate cooling equipment. If there is no cooling equipment included in the delivery volume, you can cool by means of a spray gun or a washing bottle.

ATTENTION!

Danger of injury due to brushes getting caught or pulled in. Use a spray gun or a washing bottle for cooling.

INFORMATION

Use a water-soluble and non-pollutant drilling emulsion as a cooling agent.This can be acquired from authorised distributors.

Make sure that the cooling agent is being collected.

Respect the environment when disposing of any lubricants and coolants.

Follow the manufacturer’s disposal instructions.

GB B17Pro | B23Pro | B26Pro | B33Pro

Page 38 Original operating instructions

Operation

Version 2.0.2 2014-11-04

OPTIMUM

M A S C H I N E N - G E R M A N Y

4.9 Before starting work

Before starting work, select the desired speed. It is depending on the used drilling diameter and on the material.



"Speed change“ on page 33

WARNING!

For drilling jobs, it is necessary to clamp the workpiece firmly to prevent the bit catching on the pieces. A machine vice or clamping claws is a suitable clamping device.

Put a wooden or plastic board beneath the workpiece to avoid drilling through to the work table, vice, etc.

If necessary, adjust the desired drilling depth with the drill depth stop to obtain a constant result.

When working with wood, make sure to use an adequate dust extraction unit, as sawdust can constitute a health hazard. Wear a suitable dust mask when performing works at which dust is generated.

4.10 During work

The spindle sleeve is advanced by means of the star wheel. Make sure that the feed is constant and not too fast.

The spindle sleeve is returned to its initial position by the return spring.

WARNING!

Seizing of clothes and / or hair.



Make sure to wear well-fitting clothing during drilling work.



Do not use gloves.

If necessary, use a hairnet.

CAUTION!

Danger of bumps from the levers on the star wheel. Do not release the star wheel when repositioning the drilling spindle sleeve.

The smaller the bit the more easily it may break. In the case of deep drilling, remove the bit from time to time to remove filings from the drill. Add a few drops of oil to reduce friction and prolong the service life of the bit.

CAUTION!

Danger of crushing. Do not place your hand between the drilling head and the spindle sleeve.

Operation

Version 2.0.2 2014-11-04 Original operating instructions

B17Pro | B23Pro | B26Pro | B33Pro GB

Page 39

OPTIMUM

M A S C H I N E N - G E R M A N Y

5 Determining the cutting speed and the speed

5.1 Table cutting speeds / infeed

Material table

Material to be processed

Unalloyed construction steels

< 700 N/mm²

Alloyed construction steels

> 700 N/mm²

Alloyed steels

< 1000 N/mm²

Steels, low stability

< 800 N/mm²

Steel, high stability

> 800 N/mm² non-rust steels

> 800 N/mm²

Cast iron

< 250 N/mm²

Cast iron

> 250 N/mm²

CuZn alloy brittle

CuZn alloy ductile

Aluminum alloy up to 11% Si

Thermoplastics

Thermosetting materials with organic filling

Thermosetting materials with anorganic filling

5.2 Speed table

Recommended cutting speed

Vc in m/min

30 - 35

20 - 25

15 - 25

10 - 20

60 - 100

35 - 60

30 - 50

20 - 40

15 - 35

15 - 25

2...3

0.05

0.04

0.05

0.04

0.03

0.10

0.05

0.10

0.05

0.10

0.05

0.10

0.08

0.06

0.20

0.15

0.10

0.20

0.10

>3...6

Recommended infeed f in mm/revolution

Drill bit diameter d in mm

>6...12

>12...25

0.10

0.15

0.25

0.08

0.10

0.15

0.10

0.08

0.30

0.25

0.30

0.25

0.30

0.20

0.25

0.15

0.12

0.40

0.35

0.40

0.35

0.40

0.30

Vc in m/min

Drill bit

Ø in mm

4 6 8 10 12 15 18 20 25

Speed n in rpm

30 35 40 50 60 80 100

1,0

1,5

2,0

2,5

3,0

3,5

4,0

Vc in m/min

425

364

318

849

637

510

1274 1911 2548 3185 3822 4777 5732 6369 7962 9554

1274 1699 2123

955

764

1274

1019

1592

1274

637

546

478

849

728

637

1062

910

796

2548 3185 3822 4246

1911 2389 2866 3185

1529 1911 2293 2548

1274 1592 1911 2123

1092 1365 1638 1820

955 1194 1433 1592

5308

3981

3185

2654

2275

1990

6369

4777

3822

3185

2730

2389

1114

7431

5573

4459

3715

3185

2787

12739 15924 19108 25478 31847

8493

6369

5096

4246

3640

3185

10616 12739 16985 21231

7962

6369

5308

4550

3981

9554

7643

6369

5460

4777

12739

10191

8493

7279

6369

15924

12739

10616

9099

7962

4 6 8 10 12 15 18 20 25 30 35 40 50 60 80 100

0.18

0.60

0.55

0.60

0.55

0.60

0.40

>25...50

0.35

0.20

0.35

0.20

GB B50 GSM

Page 40 Original operating instructions

Determining the cutting speed and the speed

Version 2.0.2 dated 2014-11-04

OPTIMUM

M A S C H I N E N - G E R M A N Y

159

150

142

134

127

116

106

283

255

232

212

196

182

170

26,0

27,0

28,0

29,0

20,0

21,0

22,0

23,0

24,0

25,0

30,0

31,0

32,0

13,0

14,0

15,0

16,0

17,0

18,0

19,0

33,0

34,0

35,0

36,0

37,0

38,0

Vc in m/min

8,0

8,5

9,0

9,5

10,0

11,0

12,0

6,0

6,5

7,0

7,5

Drill bit

Ø in mm

4,5

5,0

5,5

147

136

127

119

112

106

101

239

225

212

201

191

174

159

425

382

347

318

294

273

255

Speed n in rpm

122

118

114

110

106

103

100

159

152

145

138

133

127

245

227

212

199

187

177

168

398

375

354

335

318

290

265

708

637

579

531

490

455

425

127

121

116

111

106

102

196

182

170

159

150

142

134

318

300

283

268

255

232

212

566

510

463

425

392

364

340

367

354

341

329

318

308

299

478

455

434

415

398

382

735

682

637

597

562

531

503

290

281

273

265

258

251

1194

1124

1062

1006

955

869

796

2123

1911

1737

1592

1470

1365

1274

184

177

171

165

159

154

149

239

227

217

208

199

191

367

341

318

299

281

265

251

145

141

136

133

129

126

597

562

531

503

478

434

398

1062 1274 1415 1769

955 1146 1274 1592

869

796

1042

955

1158

1062

1448

1327

735

682

637

882

819

764

980

910

849

1225

1137

1062

717

674

637

603

573

521

478

796

749

708

670

637

579

531

995

937

885

838

796

724

663

174

169

164

159

155

151

193

187

182

177

172

168

220

212

205

198

191

185

179

287

273

261

249

239

229

441

409

382

358

337

318

302

245

236

227

220

212

205

199

318

303

290

277

265

255

490

455

425

398

375

354

335

241

234

227

221

215

210

306

295

284

275

265

257

249

398

379

362

346

332

318

612

569

531

498

468

442

419

15 18 20 25 30

429

413

398

384

372

360

348

557

531

507

485

464

446

857

796

743

697

656

619

587

338

328

318

310

301

293

1393

1311

1238

1173

1115

1013

929

2477

2229

2027

1858

1715

1592

1486

147

142

136

132

127

123

119

191

182

174

166

159

153

294

273

255

239

225

212

201

116

112

109

106

103

101

478

450

425

402

382

347

318

849

764

695

637

588

546

510

490

472

455

439

425

411

398

637

607

579

554

531

510

980

910

849

796

749

708

670

386

375

364

354

344

335

1592

1499

1415

1341

1274

1158

1062

2831

2548

2316

2123

1960

1820

1699

612

590

569

549

531

514

498

796

758

724

692

663

637

1225

1137

1062

995

937

885

838

483

468

455

442

430

419

1990

1873

1769

1676

1592

1448

1327

3539

3185

2895

2654

2450

2275

2123

980

944

910

879

1274

1213

1158

1108

1062

1019

849

822

796

1960

1820

1699

1592

1499

1415

1341

772

749

728

708

689

670

3185

2997

2831

2682

2548

2316

2123

5662

5096

4632

4246

3920

3640

3397

735

708

682

659

637

616

597

955

910

869

831

796

764

1470

1365

1274

1194

1124

1062

1006

579

562

546

531

516

503

2389

2248

2123

2011

1911

1737

1592

4246

3822

3474

3185

2940

2730

2548

1225

1180

1137

1098

1592

1517

1448

1385

1327

1274

1062

1027

995

2450

2275

2123

1990

1873

1769

1676

965

937

910

885

861

838

3981

3747

3539

3352

3185

2895

2654

7077

6369

5790

5308

4900

4550

4246

100

Determining the cutting speed and the speed

Version 2.0.2 dated 2014-11-04

B50 GSM GB

Page 41 Original operating instructions

OPTIMUM

M A S C H I N E N - G E R M A N Y

Drill bit

Ø in mm

39,0

40,0

41,0

42,0

43,0

44,0

45,0

46,0

47,0

48,0

49,0

50,0

Speed n in rpm

147

143

140

136

133

130

127

125

122

119

117

115

122

119

117

114

111

109

106

104

102

100

163

159

155

152

148

145

142

138

136

133

130

127

245

239

233

227

222

217

212

208

203

199

195

191

204

199

194

190

185

181

177

173

169

166

162

159

286

279

272

265

259

253

248

242

237

232

227

223

327

318

311

303

296

290

283

277

271

265

260

255

Set a speed on your drilling machine which is less than the determined speed.

INFORMATION

In order to facilitate the production of larger drill holes they need to be pre-drilled. This way, you reduce the cutting forces and improve the guiding of the drill bit.

The pre-drilling diameter is depending on the length of the chisel edge. The chisel edge does not cut, but it squeezes the material. The chisel edge is positioned at an angle of

55° to the major cutting edge.

As a general rule of thumb it applies: The pre-drilling diameter is depending on the length of the chisel edge.

Chisel edge length 10% of the drill bit - Ø

Recommended working steps for a drilling diameter of 30 mm

Example:

1st working step: Pre-drilling with Ø 5 mm.

2nd working step: Pre-drilling with Ø 15 mm.

3rd working step: Drilling with Ø 30 mm.

408

398

388

379

370

362

354

346

339

332

325

318

5.3 Examples to calculatory determine the required speed for your drilling machine

The necessary speed is depending on the diameter of the drill bit, on the material which is being machined as well as on the cutting material of the drill bit.

Material which needs to be drilled: St37

Cutting material (drill bit): HSS spiral bit

Set point of the cutting speed [ v

] according to the table: 40 meters per minute

Diameter [d] of your drill bit: 30 mm = 0,03 m [meters]

Selected infeed [f] according to the table: about 0.35 mm/rev

Speed n = =

40 m min

  

0 03m

425 rpm



490

478

466

455

444

434

425

415

407

398

390

382

653

637

621

607

593

579

566

554

542

531

520

510

817

796

777

758

741

724

708

692

678

663

650

637

GB B50 GSM

Page 42 Original operating instructions

Determining the cutting speed and the speed

Version 2.0.2 dated 2014-11-04

OPTIMUM

M A S C H I N E N - G E R M A N Y

6 Maintenance

In this chapter you will find important information about



Inspection

Maintenance

Repair of the drilling machine.

ATTENTION !

Properly performed regular maintenance is an essential prerequisite for



operational safety,



failure-free operation, long durability of the drilling machine and the quality of the products which you manufacture.

Installations and equipment from other manufacturers must also be in good order and condition.

6.1 Safety

WARNING!

The consequences of incorrect maintenance and repair work may include:



Very serious injury to personnel working on the drilling machine,



Damage to the drilling machine.

Only qualified staff should carry out maintenance and repair work on the drilling machine.

6.1.1 Preparation

WARNING!

Only carry out work on the drilling machine if it has been disconnected from the mains power supply.



"Disconnecting and securing the drilling machine“ on page 17

Attach a warning sign.

6.1.2 Restarting

Before restarting run a safety check.



"Safety check“ on page 15

WARNING!

Before activating the drilling machine, double check that this will not



no dangers generated for persons, the drilling machine is not damaged.

Maintenance

Version 2.0.2 2014-11-04 Original operating instructions

B17Pro | B23Pro | B26Pro | B33Pro GB

Page 43

OPTIMUM

M A S C H I N E N - G E R M A N Y

6.2 Inspection and maintenance

The type and level of wear depends to a large extent on the individual usage and operating conditions.

Interval Where?

What?

How?

Start of shift after every maintenance or repair work



"Safety check“ on page 15



Check if the slide rail screws for the V-belt tension on the left and right side of the drilling head are well fastened.



Check if the V-belts are well tightened. Checking the tension of V-belts,



"Speed change“ on page 33.

every week Loosening

Slide rail screws right-hand side lubricate



Lubricate the drill column regularly with commercial oil.



Lubricate the rack regularly with commercial grease (e.g. friction bearing grease).

Drilling column

Toothed rack

Every month

GB B17Pro | B23Pro | B26Pro | B33Pro

Page 44 Original operating instructions

Maintenance

Version 2.0.2 2014-11-04

Interval

every six months

Where?

What?

Visual inspection

OPTIMUM

M A S C H I N E N - G E R M A N Y

How?



Check whether the V-belts have become porous and worn.

V-belt every six months as required

Maintenance

Version 2.0.2 2014-11-04

Img.6-1: V-belt housing

Check the electrical equipment / parts of the drilling machine.



"Qualification of the staff“ on page 11

Testing



Loosen both nuts on the spring housing, approximately 1/4 counter-clockwise rotation. Under no circumstances must the nuts be completely removed from the screw thread!



Hold the spring housing with one hand, while using the other hand to slowly remove the housing.



Rotate the spring housing about its own axis until the pin snaps into the next notch.

Spring housing

Capped nut

Spindle return spring

Nut

Img.6-2: Spindle return spring

INFORMATION

If the tension has increased, rotate the housing clockwise and if the tension has decreased rotate the housing counter-clockwise.

Ensure that the notch is always snapped into the spring housing properly and subsequently tighten the nut.

The second nut secures the first nut (capped nut).

When the nuts have been tightened they should not touch the return spring housing.

Original operating instructions

B17Pro | B23Pro | B26Pro | B33Pro GB

Page 45

OPTIMUM

M A S C H I N E N - G E R M A N Y

6.3 Repair

6.3.1 Customer service technician

Request the assistance of an authorised customer service technician for any repair work. Contact your specialist dealer if you do not have customer service's information or contact Stürmer

Maschinen GmbH in Germany who can provide you with a specialist dealer's contact information. Optionally, the

Stürmer Maschinen GmbH

Dr.-Robert-Pfleger-Str. 26

D- 96103 Hallstadt can provide a customer service technician, however, the request for a customer service technician can only be made via your specialist dealer.

If the repairs are carried out by qualified technical personnel, they must follow the indications given in these operating instructions.

Optimum Maschinen Germany GmbH accepts no liability nor does it guarantee against damage and operating malfunctions resulting from failure to observe these operating instructions.

For repairs only use



 faultless and suitable tools original parts or series components expressly authorized by Optimum Maschinen Germany

GmbH.

GB B17Pro | B23Pro | B26Pro | B33Pro

Page 46 Original operating instructions

Maintenance

Version 2.0.2 2014-11-04

OPTIMUM

M A S C H I N E N - G E R M A N Y

7 Ersatzteile - Spare parts - B17Pro, B23Pro, B26Pro, B33Pro - (Vario)

7.1 OPTI B17Pro

Abb.7-1: B17Pro

Ersatzteile - Spare parts - B17Pro, B23Pro, B26Pro, B33Pro - (Vario)

Version 2.0.2 2014-11-04 Originalbetriebsanleitung

B17Pro | B23Pro | B26Pro | B33Pro DE | GB

OPTIMUM

M A S C H I N E N - G E R M A N Y

7.1.1 Bohrfutterschutz alter Typ - Drill chuck protection old type - B17Pro

7.1.2 Ersatzteilliste B17Pro

1-1

Bezeichnung

Deckel

Unterteil

CE-Label

Typenschild

Geschwindigkeitstabelle

Warnschild II

Schraube M5 x 12

Keilriemen

Spindelmutter

Riemenscheibe Spindel

Mitnehmer

Kugellager

Distanzscheibe

Seegering

Kugellager

Schraube

Riemenscheibe Motor

Schraube

Unterlegscheibe

Zugentlastung

Schraube

Kabelschelle

Hutmutter

Mutter

Rückholfeder mit Gehäuse

Abdeckung

Rückholfedersitz

Warnschild I

Schraube

Mutter

Schraube

Zahnscheibe

Schraube

Schaltergehäuse

Schraube

Bohrfutter

Schalter

Bohrkopf

Gummiring

Pinole

Kugellager

Spindel

Kegeldorn

Schraube

Stop-Stift

Schaftritzel mit Nabe

Stift

Schraube

Skalenring

Schraube

Skala

Griff

Hebel

Aludruckgussgriff

Passfeder Alugriff

Schraube Alugriff

Scheibe Alugriff

Stift

Klemmschraube

Schraube

Gummiring

Gleitstange

Feder

Schraube

Designation

Cover

Base part

CE label

Name-plate

Table - speed

Warning sign II

Screw

V-belt

Spindle nut

Spindle Pulley

Driving pin

Ball bearing

Spacing screw

Circlip

Ball bearing

Screw

Motor Pulley

Screw

Washer

Strain relief

Screw

Cable clip

Capped nut

Nut

Turbination spring with cover

Cover

Return spring seat

Warning sign

Screw

Nut

Screw

Serrated disc

Screw

Switch housing

Screw

Chuck

Switch

Boring head

Rubber ring

Pinole

Ball bearing

Spindle

Taper mandril

Screw

Display

Stop-pin

Shaft pinion with hub

Screw

Dial

Screw

Scale

Handle

Lever

Aluminium casting lever

Key aluminum handle

Screw aluminium handle

Washer aluminium handle

Clamping screw

Screw

Rubber ring

Slide rod

Spring

Screw

Menge Grösse Artikelnummer

Qty.

Size

M5 x 12

8 x 825

6203.2R

6201.2RS

M6 x 10

M6 x 12

M6 x 10

1/2"-20

M8 x 8

M8 x 18

5x3

M5 x 8

M5 x 12

M4,2x12 bis/to 2012

6005.2RS

Mk2B16

5mm

Item no.

0300317101D

0300317101U

0300317102

0300317103

0300317104

0300317105

03003171108

0300317109

0300317110

0300317111

0406203.2R

0300317113

0300317114

0406201.2R

0300317119

0300317121

0300317122

0300317124

0300317125

0300317126

0300317127

0300317128

0300317129

0300317130

0300317134

0300317136

1 alt / old type neu / new type

5x16

M8 x 17

5mm old / old type alt / old type neu / new type

6 x 10

M8 x 17

M8 x 8

3050626

0300317140

0300317142

0300317143

0300317144

0406005.2R

0300317146

3050659

0300317148

0300317149

0300317150

0300317151

0300317151-1

0300317152

0300317153

0300317154

0300317155

0300317156-1

0300317157

0300317158

03003171102

03003171100

0312367

0312368

0300317159

0300317153

M8 x 30

0300317162

0300317163

0300317164

DE | GB

B17Pro | B23Pro | B26Pro | B33Pro Ersatzteile - Spare parts - B17Pro, B23Pro, B26Pro, B33Pro - (Vario)

Originalbetriebsanleitung Version 2.0.2 2014-11-04

OPTIMUM

M A S C H I N E N - G E R M A N Y

7.1.2 Ersatzteilliste B17Pro

Bezeichnung Designation

Menge Grösse Artikelnummer

Qty.

Size Item no.

83A

100

101

103

104

105

104

Unterlegscheibe

Mutter

Motorhalteplatte

Schraube

Unterlegscheibe

Mutter

Paßfeder

Motor

Motortypenschild

Kabel

Säulenring

Schraube

Bohrtisch

Bohrtischhalter + Bohrtisch

Schraube

Mutter

Kegelstift

Stift

Klemmhebel

Unterlegscheibe

Schraube

Skala für Neigung

Antriebsschnecke

Zahnrad

Kurbel

Schraube

Zahnstange

Säule

Schraube

Maschinenfuss <5 Loch>

Maschinenfuss <4 Loch>

Inbusschlüssel

Austreiber

Mutter

Federring

Unterlegscheibe

Schraube

Säulenhalterung

Not-Aus-Schalter

Klemmksaten

Not-Aus-Schalter

Washer

Nut

Motor plate

Screw

Washer

Nut

Key

Motor

Motor name-plate

Cable

Column ring

Screw

Drilling table

Support + Drilling table

Screw

Nut

Taper pin

Clamping lever

Washer

Screw

Scale for inclination

Worm drive

Gear

Crank

Screw

Rack

Column

Screw

Machine base

M8 x 30

1/2"-12

1/4"-20

3mm

4mm

6mm

M8 x 125

113 Ein-Aus-Taster On-off button 1 ab /from 2012/230V/

KJD12

114 Klemmkasten

161 Reed Kontakt Keilriemendeckel

1S1 Schalter

SQ2 (PS-3150)

Mikroschalter

Reed Kontakt Keilriemendeckel

Steuerplatine

Microswitch

Reed contact belt cover

Control board

SQ1-HY50

PS-3150

Teile ohne Abbildung - Parts without illustration

Pinole komplett

Bohrkopf mit Pinole komplett

Terminal box

Reed contact belt cover

Switch

Pinole complete

Drilling head with pinole - complete

Komplett-Sätze - Complete sets

Kondensator

Säule + Halterung

Motorklemmkasten

Bohrfutterschutz komplett mit

Schalter, alter Typ

Socket head wrench

Drill drift

Nut

Lock washer

Washer

Screw

Column flange

Emergency Stop switch

Terminal box

Emergency Stop switch

Capacitor

Column + Column flange

Motor terminal box

Drill chuck guard complete with micro switch, old type

M6 x 10

10 ab 2004

M6 x 10

M8 x 20

12,5 µF

24V

0300317166

0300317168

0300317170

0300317172

0300317173

0300317174

0300317175

0300317176

0300317178

0300317178-1

0300317179

0300317180

0300317181

0300317182

0300317183

0300317183A

0300317184

0300317185

0300317186

0300317187

0300317188-1

0300317188

0300317190

0300317191

0300317193

03003171106

0300317194

0300317195

0300317196

0300317197

0300317199

03003171100

03003171109

03003171104

03003171105

0460058

03003171113

03003171114

0302024192

030031711S1

030031712018

0302024192

030031711A1

0300317144CPL

03003171107

03003171101

03003171103

03003171105

03003171125

Ersatzteile - Spare parts - B17Pro, B23Pro, B26Pro, B33Pro - (Vario)

Version 2.0.2 2014-11-04 Originalbetriebsanleitung

B17Pro | B23Pro | B26Pro | B33Pro DE | GB

OPTIMUM

M A S C H I N E N - G E R M A N Y

201-7

201-8

201-9

202

203

204

205

206

207

Bezeichnung Designation

201 Halter Schutzeinrichtung komplett Support protection device complete

201-1 Gehäuse Housing

201-2 Aluminium Profilaufnahme Aluminium profile admission

201-4

201-5

201-6

Klemmschraube

Stahlkugel

Federblech

Clamping screw

Steel ball

Spring plate

Flachkopfschraube

Mikroschalter

Deckel

Aluminiumprofil

Scheibe

Flachkopfschraube

Senkschraube

Schutz

Cheese head screw

Microswitch

Cover

Aluminium profile

Washer

Cheese head screw

Countersunk screw

Protection

Menge Grösse

Qty.

Size

ANSI/ASME

B18.6.5M - M4x0.7 x

SQ1-HY50

275mm

GB 955-87 - 10

GB 955-87 - 6

ANSI/ASME

B18.6.5M - M6x1 x

GB 819-85 - M6x8

135mm

Artikelnummer

Item no.

03003171201

030031712011

030031712012

030031712014

030031712015

030031712016

030031712017

030031712018

030031712019

03003171202

03003171203

03003171204

03003171206

03003171207

DE | GB

B17Pro | B23Pro | B26Pro | B33Pro Ersatzteile - Spare parts - B17Pro, B23Pro, B26Pro, B33Pro - (Vario)

Originalbetriebsanleitung Version 2.0.2 2014-11-04

OPTIMUM

M A S C H I N E N - G E R M A N Y

7.1.3 Bohrfutterschutz neuer Typ - Drill chuck protection new type - B17Pro

Bezeichnung

Innensechskantschraube

Scheibe

Innensechskantschraube

Rändelschraube

Halterung

Mikroschalter

Platte

Alu- Profil

Bohrfutterschutz A

Bohrfutterschutz B

Innensechskantschraube

Rändelschraube

Scheibe

Schraube

Halterung kpl.

Designation

Socket head screw

Washer

Socket head screw

Knurled screw

Fixture

Microswitch

Plate

Aluminium profile

Drillig chuck safety A

Drillig chuck safety B

Socket head screw

Knurled screw

Washer

Screw

Holder cpl.

Menge Grösse Artikelnummer

Qty.

Size Item no.

GB 70-85 - M6 x 10

GB 70-85 - M6 x 16

M6x16

03020333123

03020333125

03020333126

03020333127

03020333128

03003171202

03003171209

03003171210

03003171212

03003171213

03008131201CPL

Ersatzteile - Spare parts - B17Pro, B23Pro, B26Pro, B33Pro - (Vario)

Version 2.0.2 2014-11-04 Originalbetriebsanleitung

B17Pro | B23Pro | B26Pro | B33Pro DE | GB

OPTIMUM

M A S C H I N E N - G E R M A N Y

7.2 B23Pro, B23Pro Vario

Abb.7-2: B23Pro, B23Pro Vario

DE | GB

B17Pro | B23Pro | B26Pro | B33Pro Ersatzteile - Spare parts - B17Pro, B23Pro, B26Pro, B33Pro - (Vario)

Originalbetriebsanleitung Version 2.0.2 2014-11-04

OPTIMUM

M A S C H I N E N - G E R M A N Y

Typschild Motor

Schraube

Mutter

Unterlegscheibe

Motorplatte

Gleitstange rechts

Gleitstange links

Unterlegscheibe

Mutter

Kabel Motor

Kabel

Bohrkopf

Stift

Warnschild I

Klemmschraube

Schraube

Exzenter

Griff Riemenspannung

Schraube

Griff

Hebel

Aludruckgussgriff

Passfeder Alugriff

Schraube Alugriff

Scheibe Alugriff

Schraube

Schaftritzel mit Nabe

Spannstift

Klemmschraube

Skalenring

Schraube

Skala

Stop-Stift

Niete

Anzeiger

Gewindestift

Mutter

Rückholfedersitz

Rückholfeder m. Abdeckung

23A

7.2.1 Ersatzteilliste B23Pro, B23Pro Vario

Bezeichnung Designation

14-1

Schraube

Geschwindigkeitstabelle

Schraube

Unterlegscheibe

Schraube

CE Label

Typenschild

Mitnehmer

Seegering

Kugellager

Ring

Keilriemen Motor

Keilriemen Spindel

Kugellager

Riemenscheibe Mitte

Zentriervorrichtung

Paßfeder

Riemenscheibe Motor

Schraube

Spindelmutter

Riemenscheibe Spindel

Motor screw

Screw

Table - speed

Screw

Washer

Screw

CE label

Label

Driving pin

Circlip

Ball bearing

Ring

V-belt motor

V-belt spindle

Ball bearing

Middle Pulley

Centring device

Key

Motor Pulley

Screw

Spindle nut

Spindle Pulley

Motor

Motor name-plate

Screw

Nut

Washer

Motor plate

Sliding rod right

Sliding rod left

Washer

Nut

Cable motor

Cable

Head

Warning sign

Clamping screw

Screw

Eccentric bolt

Grip belt tension

Screw

Handle

Lever

Aluminium casting lever

Key aluminum lever

Screw aluminium lever

Washer aluminium lever

Screw

Shaft pinion with hub

Dowel pin

Clamping screw

Scale ring

Screw

Scale

Stop-pin

Rivet

Pointer

Grub screw

Nut

Spring seat

Turbination spring with cover

Menge Grösse Artikelnummer

Qty.

Size Item no.

M6 x 12

6204.2R

13 x 650

13 x 610

6202.2R

M8 x 12

230 V

400 V

230 V

400V

M8 x 30

M12

0300323101

0300323102

0300323103

0300323104

0300323106

0300323107

0300323108

0300323109

0300323110

0300323111

0406204.2R

0300323113

09V13650

039V13610

0406202.2R

0300323116

0300323117

0300323118

0300323119

0300323121

0300323122

0300323123

0300323323

0300323123A

0300323323A

0300323126

0300323127

0300323128

0300323129

0300323130

230 V

400 V

230 V

400 V

M8 x 16

0300323132

0300323332

0300323133

0300323333

0300323134

0300323135

0300323136

0300323137

0300323138

0300323139

0300323140

M10 x 12 alt / old type alt / old type neu / new type alt / old type neu / new type

Ø 5x20

M8 x 17

5mm

M10x30

M10

0300323142

0300323143

03003231102

03003231105

03003231104

03003231103

0300323144

0300323145

0300323145-1

0300323146

0300323147

0300323148

0300323149

0300326350

0300323151

0340116

0300323153

0340182

0300323156

0300323157

Ersatzteile - Spare parts - B17Pro, B23Pro, B26Pro, B33Pro - (Vario)

Version 2.0.2 2014-11-04 Originalbetriebsanleitung

B17Pro | B23Pro | B26Pro | B33Pro DE | GB

OPTIMUM

M A S C H I N E N - G E R M A N Y

7.2.1 Ersatzteilliste B23Pro, B23Pro Vario

Bezeichnung Designation

Menge Grösse Artikelnummer

Qty.

Size Item no.

57A

72A

88A

79A

100

101

102

103

92A

95A

104

105

106

107

108

109

210

211

Ring

Mutter

Hutmutter

Schaltergehäuse

Schraube

Schalter 230 V (ohne R/L)

Schalter 400 V (mit R/L)

Schraube

Ring

Nut

Capped nut

Switch housing

Screw

Switch 230 V (without R/L)

Switch 400 V (with R/L)

Screw

Schraube

Klammer

Warnschild II

Scheibe

Sicherungsblech

Zwischenring

Kugellager

O-Ring

Pinole

Austreiber

Kugellager

Spindel

Kegeldorn

Bohrfutter

Säulenring

Schraube

Bohrtischträger

Bohrtischträgerhalter

Zahnrad

Zahnradwelle

0-Anzeige für Neigungsskala

Schraube

Neigungsskala

Schraube

Screw

Clamp

Warning sign II

Washer

Safety plate

Ring

Ball bearing

O-ring

Pinole

Drill drift

Ball bearing

Spindle

Taper mandril

Drill chuck

Column ring

Screw

Support

Support holder

Gear

Gear axle

0-display for scale of inclination

Screw

Scale of inclination

Screw

Kegelstift

Mutter

Taper pin

Nut

Klemmhebel Clamping 1

Unterlegscheibe Washer 1

Antriebsschnecke

Kurbel

Schraube

Klemmhebel

Unterlegscheibe

Bohrtisch

Säule

Säulenhalterung

Schraube

Zahnstange

Maschinenfuss

Schraube

Inbusschlüssel

Schraube

Unterlegscheibe 8,4

Worm drive

Crank

Screw

Clamping lever

Washer

Drilling table

Column

Column flange

Screw

Rack machine base

Screw

Socket head wrench

Screw

Washer 8.4

Federring Ø 8,4

Mutter M8

Zahn-Beilegscheibe

Schraube

Inbusschlüssel

Gummiring

110 Not-Aus-Schalter

Ein-Aus-Taster

126

112

Ein-Aus-Taster

Klemmkasten

161 Reed Kontakt Keilriemendeckel

Motor mit Frequenzumrichter

Potentiometer

Steuerplatine

Schalter 230V

Schaltereinheit 400V

Lock washer

Nut

Serrated disc - shim

Screw

Socket head wrench

Rubber ring

Emergency Stop switch

On-off button

Terminal box

Reed contact belt cover

Motor with frequenci converter

Potentiometer

Control board

Switch 230V

Switch unit 400V

1/2"-20

M5 x 16

230 V

400 V

M4,2 x 12

M5 x 8

6203.2R

6205.2R

MK2 B16

M6 x 8

5mm

5/8"-11

1/4"-20

M6 x 10

M10x12

M10x13

3mm

5mm

M8x125

M5 x 8

8mm

1/4"

230V

400V

PS-3150

400V

KJD18 230V

KJD18 400V

0300323157A

0300323158

0300323159

0300323160

0300323161

0300323162

0300326362

0300323163

0300323165

0300323166

0300323167

0300323168

0300323169

0406203.2R

0300323171

0300323172

0300323172-1

0406205.2R

0300323174

3050659

3050626

0300323177

0300323179

0300323179-2

0300333392

0300323181

0313343

0300323183

0300323184

0300323185

0300323186

0300323187

0300323188

300323188A

0300323189

0300323190

0321610

0300323192A

0300323193

0300323195

0300323195-1

0300323197

0300323198

03003231100

03003231101

03003231103

03003231104

03003231106

03003231108

03003231109

0460058

03003231126

03003233126

03003171114

0302024192

0313124

0313199

030032331A1

0300323162

0300323362

DE | GB

B17Pro | B23Pro | B26Pro | B33Pro Ersatzteile - Spare parts - B17Pro, B23Pro, B26Pro, B33Pro - (Vario)

Originalbetriebsanleitung Version 2.0.2 2014-11-04

OPTIMUM

M A S C H I N E N - G E R M A N Y

7.2.1 Ersatzteilliste B23Pro, B23Pro Vario

Bezeichnung

Mikroschalter

Pinole kplt.

Säule + Halterung

Riemenscheibe Mitte kpl.

Bohrfutterschutz komplett mit

Schalter, alter Typ

Designation

Menge Grösse Artikelnummer

Qty.

Size Item no.

Microswitch 1

Komplett-Sätze - Complete sets

Pinole cpl.

Column complete

Middle pulley with centring device

Drill chuck guard complete with micro switch, old type

SQ1-HY50

24V

030031712018

0300323172CPL

0300323195CPL

0300323116-1

03003231104

Ersatzteile - Spare parts - B17Pro, B23Pro, B26Pro, B33Pro - (Vario)

Version 2.0.2 2014-11-04 Originalbetriebsanleitung

B17Pro | B23Pro | B26Pro | B33Pro DE | GB

OPTIMUM

M A S C H I N E N - G E R M A N Y

7.2.2 Bohrfutterschutz alter Typ - Drill chuck protection old type - B23Pro

Bezeichnung Designation

201-8

201-9

203

204

205

206

208

209

201 Halter Schutzeinrichtung komplett Support protection device complete

201-1 Gehäuse Housing

201-2 Aluminium Profilaufnahme Aluminium profile admission

201-4

201-5

201-6

Klemmschraube

Stahlkugel

Federblech

Clamping screw

Steel ball

Spring plate

201-7 Flachkopfschraube Cheese head screw

Mikroschalter

Deckel

Scheibe

Flachkopfschraube

Senkschraube

Schutz

Aluminiumprofil

Microswitch

Cover

Washer

Cheese head screw

Countersunk screw

Protection

Aluminium profile

Menge

Qty.

Grösse

Size

ANSI/ASME B18.6.5M

- M4x0.7 x 8

GB 955-87 - 10

GB 955-87 - 6

ANSI/ASME B18.6.5M

- M6x1 x 13

GB 819-85 - M6x8

155mm

340mm

Artikelnummer

Item no.

03003171201

030031712011

030031712012

030031712014

030031712015

030031712016

030031712017

030031712018

030031712019

03003171203

03003171204

03003171205

03003171206

03011233208

03011233209

DE | GB

B17Pro | B23Pro | B26Pro | B33Pro Ersatzteile - Spare parts - B17Pro, B23Pro, B26Pro, B33Pro - (Vario)

Originalbetriebsanleitung Version 2.0.2 2014-11-04

OPTIMUM

M A S C H I N E N - G E R M A N Y

7.2.3 Bohrfutterschutz neuer Typ - Drill chuck protection new type - B23Pro

Bezeichnung

Innensechskantschraube

Scheibe

Innensechskantschraube

Rändelschraube

Halterung

Mikroschalter

Platte

Alu- Profil

Bohrfutterschutz A

Bohrfutterschutz B

Innensechskantschraube

Rändelschraube

Scheibe

Schraube

Halterung kpl.

Designation

Socket head screw

Washer

Socket head screw

Knurled screw

Fixture

Microswitch

Plate

Aluminium profile

Drillig chuck safety A

Drillig chuck safety B

Socket head screw

Knurled screw

Washer

Screw

Holder cpl.

Menge Grösse Artikelnummer

Qty.

Size Item no.

GB 70-85 - M6 x 10

GB 70-85 - M6 x 16

M6x16

03020333123

03020333125

03020333126

03020333127

03020333128

03003171202

03003171209

03003171210

03003171212

03003171213

03008131201CPL

Ersatzteile - Spare parts - B17Pro, B23Pro, B26Pro, B33Pro - (Vario)

Version 2.0.2 2014-11-04 Originalbetriebsanleitung

B17Pro | B23Pro | B26Pro | B33Pro DE | GB

OPTIMUM

M A S C H I N E N - G E R M A N Y

7.3 OPTI B26Pro, B26Pro Vario

Abb.7-3: OPTI B26 PRO

DE | GB

B17Pro | B23Pro | B26Pro | B33Pro Ersatzteile - Spare parts - B17Pro, B23Pro, B26Pro, B33Pro - (Vario)

Originalbetriebsanleitung Version 2.0.2 2014-11-04

OPTIMUM

M A S C H I N E N - G E R M A N Y

7.3.1 Ersatzteilliste B26Pro, B26Pro Vario

Bezeichnung Designation

57a

14-1

Riemengehäuse

Schraube

Geschwindigkeitstabelle

Schraube

Unterlegscheibe

Schraube

CE Label

Typenschild

Mitnehmer

Seegering

Kugellager

Ring

Keilriemen Motor

Keilriemen Spindel

Kugellager

Riemenscheibe Mitte

Zentriervorrichtung

Paßfeder

Riemenscheibe Motor

Schraube

Spindelmutter

Riemenscheibe Spindel

Motor

Schraube

Mutter

Unterlegscheibe

Motorplatte

Gleitstange rechts

Gleitstange links

Unterlegscheibe

Mutter

Kabel Motor

Kabel

Bohrkopf

Stift

Warnschild I

Klemmschraube

Schraube

Exzenter

Griff Riemenspannung

Schraube

Griff

Hebel

Aludruckgussgriff

Passfeder Alugriff

Schraube Alugriff

Scheibe Alugriff

Schraube

Schaftritzel alt

Schaftritzel neu

Spannstift

Klemmschraube

Skalenring

Schraube

Skala

Stop-Stift

Schraube

Anzeiger

Schraube

Mutter

Rückholfedersitz

Rückholfeder mit Abdeckung

Ring

Mutter

Hutmutter

Schaltergehäuse

Pulley cover

Screw

Table - speed

Screw

Washer

Screw

CE label

Label

Driving pin

Circlip

Ball bearing

Ring

V-belt motor

V-belt spindle

Ball bearing

Middle Pulley

Centring device

Key

Motor Pulley

Scre

Spindle nut

Spindle Pulley

Motor

Screw

Nut

Washer

Motor plate

Sliding rod right

Sliding rod left

Washer

Nut

Cable motor

Cable

Boring head

Warning sign

Clamping screw

Screw

Eccentric bolt

Grip belt tension

Screw

Handle

Lever

Aluminium casting lever

Key aluminum handle

Screw aluminium handle

Washer aluminium handle

Screw

Shaft pinion

Dowel pin

Clamping screw

Scale ring

Screw

Scale

Stop-pin

Screw

Pointer

Screw

Nut

Spring seat

Turbination spring with cover

Ring

Nut

Capped nut

Switch housing

Menge Grösse Artikelnummer

Qty.

Size

M6 x 12

6205.2R

13 x 600

13 x 735

6202.2R

Item no.

0300326301

0300326302

0300323103

0300326304

0300326306

0300326307

0300326308

0300326309

0300326310

0300326311

0406205.2R

0300326313

09V13600

039V13735

0406202.2R

0300323116

0300323117

0300326318

0300323119

M8x12

230V

400 V

M8 x 30

M12

M8 x 16

M10 x 12 alt / old type alt / old type neu / new type alt neu

5 x 20

M8 x 16

5mm

0300323121

0300323122

0300323123

0300323323

0300326326

0300323162

0300323128

0300323129

0300326330

0300326332

0300326333

0300326334

0300326335

0300326336

0300323137

0300323138

0300323139

0300326340

0300326342

0300323143

03003231102

0300323105

0300323103

0300323104

0300326344

0300326345

0300326345-1

0300323146

0300323147

0300323148

0300326349

0300326350

0300323151

0300326352

0300326353

0300326354

M10

1/2"-20

0300323156

0300323157

0300326357

0300323158

0300323159

0300326360

Ersatzteile - Spare parts - B17Pro, B23Pro, B26Pro, B33Pro - (Vario)

Version 2.0.2 2014-11-04 Originalbetriebsanleitung

B17Pro | B23Pro | B26Pro | B33Pro DE | GB

OPTIMUM

M A S C H I N E N - G E R M A N Y

7.3.1 Ersatzteilliste B26Pro, B26Pro Vario

Bezeichnung Designation

Schraube M5x16

Schalter 230V (ohne R/L)

Schalter 400V (mit R/L)

Schraube

Klammer

Warnschild II

Spindelmutter

Sicherungsblech

Zwischenring

Kugellager

O-Ring

Pinole

Austreiber

Kugellager

Spindel

Kegeldorn

Bohrfutter

Säulenring

Schraube

Bohrtischträger

Bohrtischträgerhalter

Zahnrad

Zahnradwelle

O-Anzeige für Neigungsskala

Schraube

Neigungsskala

Schraube

Kegelstift

Mutter

Klemmhebel

Unterlegscheibe

Antriebsschnecke

Kurbel

Schraube

Klemmhebel

Unterlegscheibe

Bohrtisch

Säule

Säulenhalterung

Schraube

Zahnstange

Maschinenfuss

Schraube

Inbusschlüssel

Schraube

Unterlegscheibe

Federring 8,4

Mutter

Zahn-Beilegscheibe

Schraube

Inbusschlüssel

Gummiring

Keilriemen

Not-Aus-Schalter

Ein-Aus-Taster

Klemmkasten

Reed Kontakt Keilriemendeckel

Motor mit Frequenzumrichter

Potentiometer

Trafo 24V

Relais

Schalter 230V

Schaltereinheit 400V

Mikroschalter

Reed Kontakt Keilriemendeckel

Steuerplatine

111

112

161

210

211

104

105

106

107

108

109

110

100

101

102

103

92a

95a

88a

79a

72a

Screw M5x16

Switch 230 V (without R/L)

Switch 400 V (with R/L)

Screw

Clamp

Warning sign II

Washer

Safety plate

Intermediate ring

Ball bearing

O-ring

Pinole

Drill drift

Ball bearing

Spindle

Taper mandril

Drill chuck

Column ring

Screw

Support

Support holder

Gear

Gear axle

O-display for scale of inclination

Screw

Scale of inclination

Screw

Taper pin

Nut

Clamping lever

Washer

Worm driver

Crank

Screw

Clamping lever

Washer

Drilling table

Column

Column flange

Screw

Rack

Machine base

Screw

Socket head wrenc

Socket head wrench

Screw

Washer

Lock washer

Nut

Serrated disc - shim

Screw

Socket head wrench

Rubber ring

V-belt

Emergency Stop switch

On-off button

Terminal box

Reed contact belt cover

Motor with frequenci converter

Potentiometer

Transformer 24V

Relais

Switch 230V

Switch unit 400V

Microswitch

Reed contact belt cover

Control board

Menge Grösse Artikelnummer

Qty.

Size Item no.

230V

400V

M5 x 16

M5 x 8

0300326361

0300323162

0300326362

0300323163

6203.2R

6206.2R

MK3 B16

M6x8

5mm

5/8“-11

1/4"-20

M10 x 12

M 10 x 30

3mm

5mm

M8x125

M5 x 8

8mm

1/4“

13x600

0300326365

0300326366

0300326367

0300323168

0300326369

0406203.2R

0300326371

0300326372

0300326372-1

0406206.2R

0300326374

3050660

3050626

0300326377

0300326379

0300326379-1

0300333392

0300323181

0313343

0300326383

0300323184

0300323185

0300323186

0300326387

0300323188

0300326388

0300323189

0300323190

0300326391

0300326392

0300326392a

0300326393

0312603

0300326395

0300326397

0300326398

03003263100

03003263101

03003263103

03003263104

03003263106

400V

PS-3150

400V

24V

KM-TV-5

KJD18 230V

KJD18 400V

SQ1-HY50

PS-3150

03003263108

03003263109

0391620

0460058

03003233126

03003171114

0302024192

0313124

0313199

03003171104

03003171106

0300323162

0300323362

030031712018

0302024192

030032631A1

DE | GB

B17Pro | B23Pro | B26Pro | B33Pro Ersatzteile - Spare parts - B17Pro, B23Pro, B26Pro, B33Pro - (Vario)

Originalbetriebsanleitung Version 2.0.2 2014-11-04

OPTIMUM

M A S C H I N E N - G E R M A N Y

7.3.1 Ersatzteilliste B26Pro, B26Pro Vario

Bezeichnung Designation

Teile ohne Abbildung - Parts without illustration

Motorlüfterdeckel Motor fan cover

Komplett-Sätze - Complete sets

Pinole kpl.

Säule kpl.

Riemenscheibe Mitte kpl.

Werkzeugsatz in einer Box

Bohrfutterschutz komplett mit

Schalter, alter Typ

Spindle sleeve complete

Column complete

Middle Pulley complete

Tool box

Drill chuck guard complete with micro switch, old type

Menge Grösse Artikelnummer

Qty.

Size Item no.

1 24V

03003231101

0300326372CPL

0300326395CPL

0300323116-1

03003231110

03003231104

Ersatzteile - Spare parts - B17Pro, B23Pro, B26Pro, B33Pro - (Vario)

Version 2.0.2 2014-11-04 Originalbetriebsanleitung

B17Pro | B23Pro | B26Pro | B33Pro DE | GB

OPTIMUM

M A S C H I N E N - G E R M A N Y

7.3.2 Bohrfutterschutz alter Typ - Drill chuck protection old type - B26Pro

201-1

201-2

201-4

201-5

201-6

201-7

201-8

201-9

201-10

203

204

205

206

208

209

Bezeichnung

Gehäuse

Aluminium Profilaufnahme

Klemmschraube

Stahlkugel

Federblech

Flachkopfschraube

Mikroschalter

Deckel

Abstandsplatte

Scheibe

Flachkopfschraube

Senkschraube

Schutz

Aluminiumprofil

Designation

Housing

Aluminium profile admission

Clamping screw

Steel ball

Spring plate

Cheese head screw

Microswitch

Cover

Distance plate

Washer

Cheese head screw

Countersunk screw

Protection

Aluminium profile

Menge Grösse Artikelnummer

Qty.

Size Item no.

030031712011

030031712012

030031712014

030031712015

030031712016

ANSI/ASME

B18.6.5M - M4x0.7 x

030031712017

030031712018

030031712019

0300317120110

03003171203

03003171204

GB 955-87 - 10

GB 955-87 - 6

ANSI/ASME

B18.6.5M - M6x1 x 13

GB 819-85 - M6x8

155mm

340mm

03003171205

03003171206

03011233208

03011233209

DE | GB

B17Pro | B23Pro | B26Pro | B33Pro Ersatzteile - Spare parts - B17Pro, B23Pro, B26Pro, B33Pro - (Vario)

Originalbetriebsanleitung Version 2.0.2 2014-11-04

OPTIMUM

M A S C H I N E N - G E R M A N Y

7.3.3 Bohrfutterschutz neuer Typ - Drill chuck protection new type - B26Pro

Bezeichnung

Innensechskantschraube

Scheibe

Innensechskantschraube

Rändelschraube

Halterung

Mikroschalter

Platte

Alu- Profil

Bohrfutterschutz A

Bohrfutterschutz B

Innensechskantschraube

Rändelschraube

Scheibe

Schraube

Halterung kpl.

Designation

Socket head screw

Washer

Socket head screw

Knurled screw

Fixture

Microswitch

Plate

Aluminium profile

Drillig chuck safety A

Drillig chuck safety B

Socket head screw

Knurled screw

Washer

Screw

Holder cpl.

Menge Grösse Artikelnummer

Qty.

Size Item no.

GB 70-85 - M6 x 10

GB 70-85 - M6 x 16

M6x16

03020333123

03020333125

03020333126

03020333127

03020333128

03003171202

03003171209

03003171210

03003171212

03003171213

03008131201CPL

Ersatzteile - Spare parts - B17Pro, B23Pro, B26Pro, B33Pro - (Vario)

Version 2.0.2 2014-11-04 Originalbetriebsanleitung

B17Pro | B23Pro | B26Pro | B33Pro DE | GB

OPTIMUM

M A S C H I N E N - G E R M A N Y

7.4 B33Pro, B33Pro Vario

Abb.7-4: B33Pro, B33Pro Vario

DE | GB

B17Pro | B23Pro | B26Pro | B33Pro Ersatzteile - Spare parts - B17Pro, B23Pro, B26Pro, B33Pro - (Vario)

Originalbetriebsanleitung Version 2.0.2 2014-11-04

OPTIMUM

M A S C H I N E N - G E R M A N Y

7.4.1 Ersatzteilliste B33Pro, B33Pro Vario

Bezeichnung Designation

13 a

14 a

12 a

Keilriemen Spindel

Mutter

Riemenscheibe Spindel

Mitnehmer

Sicherungsring

Kugellager

Distanzbuchse

Mutter

Zahnscheibe

Unterlegscheibe

Kugellager

Geschwindigkeitstabelle

Warnschild II

Riemengehäuse

CE Label

Typenschild

Schraub

Schraube

Kabelklemme

Keilriemen Motor

Kugellager

Riemenscheibe Mitte

Zentrierstück

Schraube

Riemenscheibe Motor

Motor

32 a

28 a

Mutter

Beilegscheibe

Schraube

Motorhalteplatte

Federring

Unterlegscheibe

Mutter

Gleitstange rechts

Gleitstange links

Schraube

Unterlegscheibe

Gummiring

Schraube

Exzenter

Bohrkopf

36 a

Schild

Klemmschraube

Hebel

Ring

Niet

Warnschild I

42a Mutter

42 Hutmutter

Rückholfeder mit Gehäuse

Stift

Federsitz

Mutter

Unterlegscheibe

Schraube

Unterlegscheibe

Schraube

Schaltergehäuse

Schraube

Geschwindigkeitstabelle

Schalter

Schraube

Stift

Nut

Washer

Screw

Motor plate

Lock washer

Washer

Nut

Sliding rod right

Sliding rod left

Screw

Washer

Rubber ring

Screw

Eccentric bolt

Boring head

Name-plate

Clamping screw

Lever

Ring

Rivet

Warning sign

Nut

V-belt spindle

Nut

Spindle pulley

Driving pin

Safety ring

Ball bearing

Bushing

Nut

Serrated disc

Washer

Ball bearing

Table - speed

Warning sign II

Pulley cover

CE label

Name-plate

Screw

Cable clamp

V-belt motor

Ball bearing

Middle Pulley

Centring piece

Screw

Motor Pulley

Motor

Return spring with housing

Spring seat

Nut

Washer

Screw

Washer

Screw

Switch housing

Screw

Table - speed

Switch

Screw

Qty.

Menge Grösse Artikelnummer

Size

13 x 735

6206-2R

6204.2R

Item no.

039V13735

0300333302

0300333303

0300333304

0300333305

0406206.2R

0300333307

0300333308

0300333309

0300333340

0406204.2R

0300333312

0300333312a

0300333313

0300333314

M5x10

M 5x8

13 x 860

6202.2R

M 8x12

400V

0300333316

0300333301

0406202.2R

0300333319

0300333320

0300333322

0300333323

M 10

M 10x30

M12

M6 x 16

M8x16

6x16

25 x 10

M 10

M 10x27

M5x8

M6x16

M6x30

400V

M5x12

M8x25

M10x12

8x25

0300333355

0300326362

0300333360

0300333325

0300333327

0300333328

0300333328a

0300333330

0300333331

0300333332a

0300333333

0300333335

0300333336

0300333337

0300333338

0300333339

0300333340

0300333341

0300333342

0300333342-1

0300333343

0300333344

0300333345

0300333346

0300333348

0300333350

0300333352

Ersatzteile - Spare parts - B17Pro, B23Pro, B26Pro, B33Pro - (Vario)

Version 2.0.2 2014-11-04 Originalbetriebsanleitung

B17Pro | B23Pro | B26Pro | B33Pro DE | GB

OPTIMUM

M A S C H I N E N - G E R M A N Y

98 a

100

101

102

103

103 a

117

118

119

120

121

161

211

212

104

105

106

108

109

115

116

0-Skala

Stift

Säulenring

Schraube

Klemmhebel

Unterlegscheibe

Kurbel

Schraube

Griff

Zahnstange

Säule

Säulenhalterung

Schraube

Inbusschraube

Maschinenfuss

Kabel

Inbusschlüssel 3mm

Inbusschlüssel 4mm

Inbusschlüssel 5mm

Inbusschlüssel 6mm

Not-Aus-Schalter

Ein-Aus-Taster

Klemmkasten

Reed Kontakt Keilriemendeckel

Motor mit Frequenzumrichter

Potentiometer

Trafo 24V

Relais

Schalter 230V

Schaltereinheit 400V

Stift

Skalenring

Klemmschraube

Bohrtiefenskala

Kerbstift

Hebel

Aludruckgussgriff

Passfeder Alugriff

Schraube Alugriff

Scheibe Alugriff

Griff

Keil

Gummiring

Pinole

Kugellager

Spindel

Austreiber

Kegeldorn

Bohrfutter

Bohrtisch

Neigungsskala

Kerbstift

Schraube

Bolzen

Klemmhebel

Bohrtischhalter

Antriebsschnecke

Zahnrad

Schraube

7.4.1 Ersatzteilliste B33Pro, B33Pro Vario

Bezeichnung

Stop-Stift

Schraube

Zeiger

Schaftritzel

Designation

Menge Grösse Artikelnummer

Qty.

Size Item no.

Stop-pin

Screw

Pointer

Shaft pinion

Scale ring

Clamping screw

Scale - drilling depth

Fluted pin

Lever

Aluminium casting lever

Key aluminum handle

Screw aluminium handle

Washer aluminium handle

Handle

Key

Rubber ring

Pinole

Ball bearing

Spindle

Drill drift

Taper mandril

Drill chuck

Drilling table

Scale of inclination

Fluted pin

Screw

Bolt

Clamping lever

Support

Worm drive

Gear-wheel

Screw

0-scale

Column ring

Screw

Clamping lever

Washer

Crank 1

Screw 1

Grip

Rack

Column

Column flange

Screw

Socket head wrench

Machine base

Cable

Socket head wrench 3mm

Socket head wrench 4mm

Socket head wrench 5mm

Socket head wrench 6mm

Emergency Stop switch

On-off button

Terminal box

Reed contact belt cover

Motor with frequenci converter

Potentiometer

Transformer 24V

Relais

Switch 230V

Switch unit 400V

M8x30 alt / old type neu / new type

5x20

5mm alt / old type neu / new type alt / old type

6208.2R

MK4 B16

5mm

M6x10

M 12x45

400V

PS-3150

400V

24V

KM-TV-5

KJD18 230V

KJD18 400V

0300333362

0300333398

0300333399

0300333364

0300333365

0300333366

0300333366-1

0300333367

0300333368

0300333369

0300333370

0300333371

0300333372

03003333104

03003231105

03003231103

03003231104

0300333373

0300333374

0300333375

0300333376

04051208

0406208.2R

0300333379

0300333380

3050661

3050626

0300333384

0300333385

0300333386

0300333387

0300333388

0300333389

0300333390

0300333391

0300333392

0313321

03003333100

0300333395

0300333396

03003333101

03003333102

03003333103

03003333103-1

03003333104

03003333105

03003333105-1

03003333106

03003333108

03003333109

03003333115

03003333116

03003333117

03003333118

0460058

03003233126

03003171114

0302024192

0313134

0313199

03003171104

03003171106

0300323162

0300323362

DE | GB

B17Pro | B23Pro | B26Pro | B33Pro Ersatzteile - Spare parts - B17Pro, B23Pro, B26Pro, B33Pro - (Vario)

Originalbetriebsanleitung Version 2.0.2 2014-11-04

OPTIMUM

M A S C H I N E N - G E R M A N Y

7.4.1 Ersatzteilliste B33Pro, B33Pro Vario

Bezeichnung Designation

Mikroschalter

Reed Kontakt Keilriemendeckel

Steuerplatine

Microswitch

Reed contact belt cover

Control board

Teile ohne Abbildung - Parts without illustration

Motorlüfterdeckel

Klemmkasten

Bohrfutterschutz alter Typ

Motor fan cover

Motor connection box

Drill chuck guard old type

Komplett-Sätze - Complete sets

Pinole kpl.

Säule kpl.

Werkzeugsatz in einer Box

Bohrfutterschutz mit Schalter komplett

Pinole complete

Column complete

Tool box

Drill chuck guard with micro switch complete

Menge Grösse Artikelnummer

Qty.

Size Item no.

SQ1-HY50

PS-3150

030031712018

0302024192

030033331A1

1 24V

03003333107

3003335

0300333376CPL

03003333103CPL

0313350

03003333125

Ersatzteile - Spare parts - B17Pro, B23Pro, B26Pro, B33Pro - (Vario)

Version 2.0.2 2014-11-04 Originalbetriebsanleitung

B17Pro | B23Pro | B26Pro | B33Pro DE | GB

OPTIMUM

M A S C H I N E N - G E R M A N Y

7.4.2 Bohrfutterschutz alter Typ - Drill chuck protection old type - B33Pro

201-1

201-2

201-4

201-5

201-6

201-7

201-8

201-9

201-10

203

204

205

206

208

210

Bezeichnung

Gehäuse

Aluminium Profilaufnahme

Klemmschraube

Stahlkugel

Federblech

Flachkopfschraube

Mikroschalter

Deckel

Abstandsplatte

Scheibe

Flachkopfschraube

Senkschraube

Schutz

Aluminiumprofil

Designation

Housing

Aluminium profile admission

Clamping screw

Steel ball

Spring plate

Cheese head screw

Microswitch

Cover

Distance plate

Washer

Cheese head screw

Countersunk screw

Protection

Aluminium profile

Menge Grösse Artikelnummer

Qty.

Size Item no.

030031712011

030031712012

030031712014

030031712015

030031712016

ANSI/ASME

B18.6.5M - M4x0.7 x

SQ1-HY50

030031712017

030031712018

030031712019

0300317120110

03003171203

03003171204

GB 955-87 - 10

GB 955-87 - 6

ANSI/ASME

B18.6.5M - M6x1 x 13

GB 819-85 - M6x8

155mm

385mm

03003171205

03003171206

03011233208

03003333210

DE | GB

B17Pro | B23Pro | B26Pro | B33Pro Ersatzteile - Spare parts - B17Pro, B23Pro, B26Pro, B33Pro - (Vario)

Originalbetriebsanleitung Version 2.0.2 2014-11-04

OPTIMUM

M A S C H I N E N - G E R M A N Y

7.4.3 Bohrfutterschutz neuer Typ - Drill chuck protection new type - B33Pro

Bezeichnung

Innensechskantschraube

Scheibe

Innensechskantschraube

Rändelschraube

Halterung

Mikroschalter

Platte

Alu- Profil

Bohrfutterschutz A

Bohrfutterschutz B

Innensechskantschraube

Rändelschraube

Scheibe

Schraube

Halterung kpl.

Designation

Socket head screw

Washer

Socket head screw

Knurled screw

Fixture

Microswitch

Plate

Aluminium profile

Drillig chuck safety A

Drillig chuck safety B

Socket head screw

Knurled screw

Washer

Screw

Holder cpl.

Menge Grösse Artikelnummer

Qty.

Size Item no.

GB 70-85 - M6 x 10

GB 70-85 - M6 x 16

M6x16

03020333123

03020333125

03020333126

03020333127

03020333128

03003171202

03003171209

03003171210

03003171212

03003171213

03008131201CPL

Ersatzteile - Spare parts - B17Pro, B23Pro, B26Pro, B33Pro - (Vario)

Version 2.0.2 2014-11-04 Originalbetriebsanleitung

B17Pro | B23Pro | B26Pro | B33Pro DE | GB

OPTIMUM

M A S C H I N E N - G E R M A N Y

7.5 Schaltplan - Wiring diagram - B17Pro, B23Pro - 230V

DE | GB

B17Pro | B23Pro | B26Pro | B33Pro Ersatzteile - Spare parts - B17Pro, B23Pro, B26Pro, B33Pro - (Vario)

Originalbetriebsanleitung Version 2.0.2 2014-11-04

OPTIMUM

M A S C H I N E N - G E R M A N Y

7.6 Schaltplan - Wiring diagram - B23Pro, B26Pro, B33Pro - 400 V

Ersatzteile - Spare parts - B17Pro, B23Pro, B26Pro, B33Pro - (Vario)

Version 2.0.2 2014-11-04 Originalbetriebsanleitung

B17Pro | B23Pro | B26Pro | B33Pro DE | GB

OPTIMUM

M A S C H I N E N - G E R M A N Y

7.7 Schaltplan - Wiring diagram - B23Pro Vario, B26Pro Vario, B33Pro Vario

DE | GB

B17Pro | B23Pro | B26Pro | B33Pro Ersatzteile - Spare parts - B17Pro, B23Pro, B26Pro, B33Pro - (Vario)

Originalbetriebsanleitung Version 2.0.2 2014-11-04

OPTIMUM

M A S C H I N E N - G E R M A N Y

8 Malfunctions

8.1 Malfunctions on the drilling machine

Malfunction

Release of the FI protected switch

Noise during work.

Drill bit "burnt“

Cause/ possible effects

• an unusual

FI protective switch is being used

• Spindle turning dry

• Tool blunt or incorrectly secured

• Incorrect speed

• The filings have not been removed

•

• from the bore hole

Blunt drill bit.

Operating without cooling agent

Solution

•



"Power supply“ on page 29

• Grease spindle

• Use new tool and check securing

(fixed setting of the bit, bit holder and chuck).

• Select another rate, feed too high

• Retract the drill bit from the bore hole more often.

• Sharpen the drill bit or insert new drill bit.

• Use cooling agent

• Use a new drill bit.

Drill point runs off, drilled hole is not circular.

• Hard fibre in wood or length of the cutting twist or the drill bit is uneven.

• Drill bit is bent.

• No base / support used.

Drill bit defective.

Drill bit runs unround or wobbles.

• Drill bit is bent.

• Worn bearing on boring head.

• Drill is not correctly clamped.

• Drill chuck defective

• Place a piece of wood underneath the workpiece and fasten this to the workpiece.

• Replace drill bit

• Have the bearing on the boring head replaced.

• Set the correct tension to the drill bit.

• Exchange the drill chuck.

• Clean the surfaces accurately

• Keep surfaces free of grease

The drill chuck or the taper mandril cannot be inserted.

Motor does not start

Motor is overheating and there is no power

• Dirt, grease or oil on the taper inside of the drill chuck or on the taper surface of the drill spindle

• Motor is wrongly connected

• Defective fuse

• Motor overloaded

• Too low mains voltage

• Motor is wrongly connected

• Have it checked by authorised personnel.

• Disconnect immediately and have the equipment checked by a trained specialist

Precision of the work deficient • Heavy and unbalanced or deformed part

• Inexact horizontal position of the part holder

• Balance the piece statically and secure without straining

• Adjust part-holder

Drilling spindle sleeve does not return to its initial position

• Spindle return spring •

“Spindle return spring“ on page 45

Malfunctions

Version 2.0.2 2014-11-04 Original operating instructions

B17Pro | B23Pro | B26Pro | B33Pro GB

Page 73

OPTIMUM

M A S C H I N E N - G E R M A N Y

9 Annex

9.1 Copyright

This document is copyright. All derived rights are also reserved, especially those of translation, re-printing, use of figures, broadcast, reproduction by photo-mechanical or similar means and recording in data processing systems, neither partial nor total.

Subject to technical changes without notice.

9.2 Terminology/Glossary

Term

Drill sleeve

Drilling spindle

Quick-action drill chuck

Drill chuck

Drill drift

Taper mandrel

Tool

Workpiece

Drilling table

Drill head

Star wheel

Explanation

Fixed hollow shaft in which the drilling spindle turns

Shaft activated by the motor

Drill chuck can be fixed by hand.

Drill bit chuck

Tool to release the bit or the drill chuck from the drill spindle

Cone of the drill or of the drill chuck

Milling cutter, drill bit, countersink, etc.

Workpiece to be turned drilled or machined.

Supporting surface, clamping surface upper part of the drilling machine

Manual operation for the drill feed

9.3 Change information manual

Chapter

EC declaration

All

1 + 4

Short note

changed standard

Merging of standard + Vario

Image switch of drill chuck protection

Type plates + speed tables

new version no.

1.2.9

2.0

2.0.1

2.0.2

GB B17Pro | B23Pro | B26Pro | B33Pro

Page 74 Original operating instructions

Annex

Version 2.0.2 2014-11-04

OPTIMUM

M A S C H I N E N - G E R M A N Y

9.4 Liability claims for defects / warranty

Beside the legal liability claims for defects of the customer towards the seller the manufacturer of the product, OPTIMUM GmbH, Robert-Pfleger-Straße 26, D-96103 Hallstadt, does not grant any further warranties unless they are listed below or had been promised in the frame of a individual contractual agreement.



The processing of the liability claims or of the warranty is performed as chosen by

OPTIMUM GmbH either directly or through one of its dealers.

Any defective products or components of such products will either be repaired or replaced by components which are free from defects. The property of replaced products or components passes on to OPTIMUM GmbH.

The automatically generated original proof of purchase which shows the date of purchase, the type of machine and the serial number, if applicable, is the precondition in order to assert liability or warranty claims. If the original proof of purchase is not presented, we are not able to perform any services.

Defects resulting from the following circumstances are excluded from liability and warranty claims:

- Using the product beyond the technical options and proper use, in particular due to overstraining of the machine

- Any defects arising by one's own fault due to faulty operations or if the operating manual is disregarded

- Inattentive or incorrect handling and use of improper equipment

- Non-authorised modifications and repairs

- Insufficient installation and safeguarding of the machine

- Disregarding the installation requirements and conditions of use

- Atmospheric discharges, overvoltage and lightning strokes as well as chemical influences

The following items are as well not subject to the liability or warranty claims:

- Wearing parts and components which are subject to a standard wear as intended such as e.g. V-belts, ball bearings, illuminants, filters, sealings, etc.

- Non reproducible software errors

Any services which OPTIMUM GmbH or one of its servants performs in order to fulfil in the frame of an additional guarantee are neither an acceptance of the defects nor an acceptance of its obligation to compensate. Such services do neither delay nor interrupt the warranty period.

Place of jurisdiction among traders is Bamberg.

If one of the above mentioned agreements is totally or partially inefficient and/or null, it is considered as agreed what is closest to the will of the warrantor and which remains in the framework of the limits of liability and warranty which are predefined by this contract.

9.5 Advice for disposal / Options of re-use

Please dispose of your machine in an environmentally friendly way, not by disposing of the waste not in the environment, but by acting in a professional way.

Please do not throw away the packaging and the used machine later on, but dispose of your material according to the guidelines established by your municipality or by the responsible waste management company.

Annex

Version 2.0.2 2014-11-04 Original operating instructions

B17Pro | B23Pro | B26Pro | B33Pro GB

Page 75

OPTIMUM

M A S C H I N E N - G E R M A N Y

9.5.1 Decommissioning

CAUTION!

Immediately decommission used machines in order to avoid later misuse and endangering of the environment or of persons.



Disconnect the machine from the mains.

Cut the connecting cable into two.

Remove all operating materials from the used device which are harmful to the environment.

If required, remove the batteries and accumulators.



If required, disassemble the machine into easy-to-handle and usable components and parts.

Supply the machine components and operating materials to the provided disposal routes.

9.5.2 Disposal of the packaging of the new machine

All used packaging materials and packaging aids of the machine are recyclable and generally need to be transported to the material recycling.

The packaging wood can be supplied to the disposal or reuse.

It is possible to crush any packaging material made of cardboard and supply it to the waste paper collection.

The films are made of polyethylene (PE) and the upholstery parts are made of polystyrene

(PS). It is possible to reuse these materials after reconditioning, if you supply them to the collection station or to the responsible waste management company.

Supply the packaging material only correctly sorted, so that it is possible to directly supply it to the reuse.

9.5.3 Disposal of the used machine

INFORMATION

Please take care in your interest and in the interest of the environment that all component parts of the machine are only disposed of in the intended and admitted way.

Please note that electrical devices include a number of reusable materials as well as components which are harmful to the environment. Please help that these components are disposed of separately and professionally. In case of doubt, please contact your municipal waste management company. If necessary contact a specialised waste disposal centre to get help for the disposal.

9.5.4 Disposal of electrical and electronic components

Please make sure that the electrical components are disposed of professionally and according to the legal regulations.

The machine is composed of electrical and electronic components and must not be disposed of as household waste. According to the European directive 2002/96/EC regarding electrical and electronic used devices and the implementation of national legislation used power tools and electrical machines need to be collected separately and supplied to an environmentally friendly recycling centre.

Being the machine operator, you should gather information regarding the authorised collection or disposal system which applies for your company.

Please make sure that batteries and/or accumulators are disposed of in a professional way and according to the legal regulations. Please throw empty accumulators only into the collection boxes of retail markets or municipal waste disposal companies.

GB B17Pro | B23Pro | B26Pro | B33Pro

Page 76 Original operating instructions

Annex

Version 2.0.2 2014-11-04

OPTIMUM

M A S C H I N E N - G E R M A N Y

9.5.5 Disposal of lubricants and cooling lubricants

ATTENTION!

Please imperatively make sure that the used coolants and lubricants are disposed of in an environmentally friendly way. Observe the disposal advices of your municipal waste management companies.

INFORMATION

Do not mix up used coolant emulsions and oils, since only used oils which had not been mixed up are recyclable.

The disposal advices for the used lubricants are made available by the manufacturer for lubricants. If necessary, ask for the product-specific data sheets.

9.6 Disposal via municipal collecting points

Disposal of used electrical and electronic components

Disposal of used electric and electronic devices(Applicable in the countries of the European

Union and other European countries with a separate collecting system for such devices).

The sign on the product or on its packing indicates that the product must not be handled as common household waist, but that it needs to be delivered to a central collection point for recycling. Your contribution to the correct disposal of this product will protect the environment and the health of your fellow men. The environment and the health are endangered by incorrect disposal. Recycling of material will help to reduce the consumption of raw materials. Your District Office, the municipal waste collection station or the shop where you have bought the product will inform you about the recycling of this product.

9.7 RoHS , 2002/95/CE

The sign on the product or on its packaging indicates that this product complies with the

European guideline 2002/95/EC.

9.8 Product follow-up

We have a follow-up service for our products which extends even after shipment.

We would be grateful if you could send us the following information:



Modified settings experiences with the bench drill and upright drill, which could be important for other users

Recurring failures

Optimum Maschinen Germany GmbH

Dr.-Robert-Pfleger-Str. 26

D-96103 Hallstadt

Telefax +49 (0) 951 - 96 555 - 888

E-Mail: [email protected]

Annex

Version 2.0.2 2014-11-04 Original operating instructions

B17Pro | B23Pro | B26Pro | B33Pro GB

Page 77

OPTIMUM

M A S C H I N E N - G E R M A N Y

9.9 EC - Declaration of Conformity B17Pro

The manufacturer / retailer:

Optimum Maschinen Germany GmbH

Dr.-Robert-Pfleger-Str. 26

D - 96103 Hallstadt

hereby declares that the following product,

Product designation:

Bench drilling machine

B17Pro

Type designation:

Serial number:

Year of construction:

_ __ __ __ __

20__ all relevant provisions of the Machinery Directive (2006/42/EC) corresponds.

The machine continues to comply with all provisions of the Directives Electrical equipment (2014/35/EC) and electromagnetic compatibility (2014/30/EC).

The following harmonized standards were applied:

EN 12717:2001+A1:2009

Safety of machine tools - drilling machines

EN ISO 12100:2010

EN 60204-1

Safety of machines - General design principles - Risk evaluation and risk reduction

Safety of machinery - electrical equipment of machines, Part 1: general requirements

Person responsible for the document: Kilian Stürmer, Phone: +49 (0) 951 96 555-800

Address: Dr.-Robert-Pfleger-Str. 26

D - 96103 Hallstadt

Kilian Stürmer

(CEO, General manager)

Hallstadt, 2014-10-24

GB B17Pro | B23Pro | B26Pro | B33Pro

Page 78 Original operating instructions Version 2.0.2 2014-11-04

OPTIMUM

M A S C H I N E N - G E R M A N Y

9.10 EC - Declaration of Conformity B23Pro

The manufacturer / retailer:

Optimum Maschinen Germany GmbH

Dr.-Robert-Pfleger-Str. 26

D - 96103 Hallstadt

hereby declares that the following product

Product designation:

Bench drilling machine

B23Pro

Type designation:

Serial number:

Year of construction:

_ __ __ __ __

20__ all relevant provisions of the Machinery Directive (2006/42/EC) corresponds.

The machine continues to comply with all provisions of the Directives Electrical equipment (2014/35/EC) and electromagnetic compatibility (2014/30/EC).

The following harmonized standards were applied:

EN 12717:2001+A1:2009

Safety of machine tools - drilling machines

EN ISO 12100:2010

EN 60204-1

Safety of machines - General design principles - Risk evaluation and risk reduction

Safety of machinery - electrical equipment of machines, Part 1: general requirements

Person responsible for the document: Kilian Stürmer, Phone: +49 (0) 951 96 555-800

Address: Dr.-Robert-Pfleger-Str. 26

D - 96103 Hallstadt

Kilian Stürmer

(CEO, General manager)

Hallstadt, 2014-10-24

Version 2.0.2 2014-11-04 Original operating instructions

B17Pro | B23Pro | B26Pro | B33Pro GB

Page 79

OPTIMUM

M A S C H I N E N - G E R M A N Y

9.11 EC - Declaration of Conformity B23Pro Vario

The manufacturer / retailer:

Optimum Maschinen Germany GmbH

Dr.-Robert-Pfleger-Str. 26

D - 96103 Hallstadt

hereby declares that the following product

Product designation:

Bench drilling machine

B23Pro Vario

Type designation:

Serial number:

Year of construction:

_ __ __ __ __

20__ all relevant provisions of the Machinery Directive (2006/42/EC) corresponds.

The machine continues to comply with all provisions of the Directives Electrical equipment (2014/35/EC) and electromagnetic compatibility (2014/30/EC).

The following harmonized standards were applied:

EN 12717:2001+A1:2009

Safety of machine tools - drilling machines

EN ISO 12100:2010

EN 60204-1

EN 55011 class A: 2003.-08

Safety of machines - General design principles - Risk evaluation and risk reduction

Safety of machinery - electrical equipment of machines, Part 1: general requirements

Industrial, scientific radio-frequency equipment.

Person responsible for the document: Kilian Stürmer, Phone: +49 (0) 951 96 555-800

Address: Dr.-Robert-Pfleger-Str. 26

D - 96103 Hallstadt

Kilian Stürmer

(CEO, General manager)

Hallstadt, 2014-10-24

GB B17Pro | B23Pro | B26Pro | B33Pro

Page 80 Original operating instructions Version 2.0.2 2014-11-04

9.12 EC - Declaration of Conformity B26Pro

The manufacturer / retailer:

Optimum Maschinen Germany GmbH

Dr.-Robert-Pfleger-Str. 26

D - 96103 Hallstadt

hereby declares that the following product

Product designation:

Upright drilling machine

B26Pro

Type designation:

Serial number:

Year of construction:

_ __ __ __ __

20__

OPTIMUM

M A S C H I N E N - G E R M A N Y

all relevant provisions of the Machinery Directive (2006/42/EC) corresponds.

The machine continues to comply with all provisions of the Directives Electrical equipment (2014/35/EC) and electromagnetic compatibility (2014/30/EC).

The following harmonized standards were applied:

EN 12717:2001+A1:2009

Safety of machine tools - drilling machines

EN ISO 12100:2010

EN 60204-1

Safety of machines - General design principles - Risk evaluation and risk reduction

Safety of machinery - electrical equipment of machines, Part 1: general requirements

Person responsible for the document: Kilian Stürmer, Phone: +49 (0) 951 96 555-800

Address: Dr.-Robert-Pfleger-Str. 26

D - 96103 Hallstadt

Kilian Stürmer

(CEO, General manager)

Hallstadt, 2014-10-24

Version 2.0.2 2014-11-04 Original operating instructions

B17Pro | B23Pro | B26Pro | B33Pro GB

Page 81

OPTIMUM

M A S C H I N E N - G E R M A N Y

9.13 EC - Declaration of Conformity B26Pro Vario

The manufacturer / retailer:

Optimum Maschinen Germany GmbH

Dr.-Robert-Pfleger-Str. 26

D - 96103 Hallstadt

hereby declares that the following product

Product designation:

Upright drilling machine

B26Pro Vario

Type designation:

Serial number:

Year of construction:

_ __ __ __ __

20__ all relevant provisions of the Machinery Directive (2006/42/EC) corresponds.

The machine continues to comply with all provisions of the Directives Electrical equipment (2014/35/EC) and electromagnetic compatibility (2014/30/EC).

The following harmonized standards were applied:

EN 12717:2001+A1:2009

Safety of machine tools - drilling machines

EN ISO 12100:2010

EN 60204-1

EN 55011 class A: 2003.-08

Safety of machines - General design principles - Risk evaluation and risk reduction

Safety of machinery - electrical equipment of machines, Part 1: general requirements

Industrial, scientific radio-frequency equipment.

Person responsible for the document: Kilian Stürmer, Phone: +49 (0) 951 96 555-800

Address: Dr.-Robert-Pfleger-Str. 26

D - 96103 Hallstadt

Kilian Stürmer

(CEO, General manager)

Hallstadt, 2014-10-24

GB B17Pro | B23Pro | B26Pro | B33Pro

Page 82 Original operating instructions Version 2.0.2 2014-11-04

9.14 EC - Declaration of Conformity B33Pro

The manufacturer / retailer:

Optimum Maschinen Germany GmbH

Dr.-Robert-Pfleger-Str. 26

D - 96103 Hallstadt

hereby declares that the following product

Product designation:

Upright drilling machine

B33Pro

Type designation:

Serial number:

Year of construction:

_ __ __ __ __

20__

OPTIMUM

M A S C H I N E N - G E R M A N Y

all relevant provisions of the Machinery Directive (2006/42/EC) corresponds.

The machine continues to comply with all provisions of the Directives Electrical equipment (2014/35/EC) and electromagnetic compatibility (2014/30/EC).

The following harmonized standards were applied:

EN 12717:2001+A1:2009

Safety of machine tools - drilling machines

EN ISO 12100:2010

EN 60204-1

Safety of machines - General design principles - Risk evaluation and risk reduction

Safety of machinery - electrical equipment of machines, Part 1: general requirements

Person responsible for the document: Kilian Stürmer, Phone: +49 (0) 951 96 555-800

Address: Dr.-Robert-Pfleger-Str. 26

D - 96103 Hallstadt

Kilian Stürmer

(CEO, General manager)

Hallstadt, 2014-10-24

Version 2.0.2 2014-11-04 Original operating instructions

B17Pro | B23Pro | B26Pro | B33Pro GB

Page 83

OPTIMUM

M A S C H I N E N - G E R M A N Y

9.15 EC - Declaration of Conformity B33Pro Vario

The manufacturer / retailer:

Optimum Maschinen Germany GmbH

Dr.-Robert-Pfleger-Str. 26

D - 96103 Hallstadt

hereby declares that the following product,

Product designation:

Upright drilling machine

B33Pro Vario

Type designation:

Serial number:

Year of construction:

_ __ __ __ __

20__ all relevant provisions of the Machinery Directive (2006/42/EC) corresponds.

The machine continues to comply with all provisions of the Directives Electrical equipment (2014/35/EC) and electromagnetic compatibility (2014/30/EC).

The following harmonized standards were applied:

EN 12717:2001+A1:2009

Safety of machine tools - drilling machines

EN ISO 12100:2010

EN 60204-1

EN 55011 class A: 2003.-08

Safety of machines - General design principles - Risk evaluation and risk reduction

Safety of machinery - electrical equipment of machines, Part 1: general requirements

Industrial, scientific radio-frequency equipment

Person responsible for the document: Kilian Stürmer, Phone: +49 (0) 951 96 555-800

Address: Dr.-Robert-Pfleger-Str. 26

D - 96103 Hallstadt

Kilian Stürmer

(CEO, General manager)

Hallstadt, 2014-10-24

GB B17Pro | B23Pro | B26Pro | B33Pro

Page 84 Original operating instructions Version 2.0.2 2014-11-04

OPTIMUM

M A S C H I N E N - G E R M A N Y

Index

Accident report

....................................................18

Assembly

............................................................22

Classification of hazards

........................................................8

Customer service

................................................46

Customer service technician

...............................46

Disposal

..............................................................77

Drill chuck assembly

........................................................38

disassembly

...................................................38

EC Declaration of Conformity

.......................................................................84

Electrical connection

...........................................30

Electrical system safety

.............................................................18

Inspection

............................................................43

Intended use

.........................................................9

Maintenance

.......................................................43

Malfunctions drilling machine

..............................73

Misuse

.................................................................10

Obligations of the operating company

..............................12

of the operator

...............................................12

Operator positions

...............................................13

Pictograms

............................................................9

Protective equipment

......................................................16

Qualification of the staff safety

.............................................................11

Repair

.................................................................43

RoHS

..................................................................77

Safety devices

...........................................................13

during maintenance

.......................................17

during operation

.............................................17

Safety instructions

.................................................8

Scope of delivery

................................................22

Specialist dealer

..................................................46

Storage and packaging

.......................................23

Switching off the machine

...................................................37

Switching on the machine

................................................... 37

Table cutting speeds

.......................................... 40

Technical data

Emissions

...................................................... 20

Tool disassembly

................................................... 38

Warming up the machine

.................................... 30

Warning notes

...................................................... 8

Original operating instructions

B17Pro | B23Pro | B26Pro | B33Pro GB

Page 85 Version 2.0.2 2014-11-04

OPTIMUM

M A S C H I N E N - G E R M A N Y

GB B17Pro | B23Pro | B26Pro | B33Pro

Page 86 Original operating instructions Version 2.0.2 2014-11-04

Hej! Jag är en AI-chattbot som är särskilt tränad för att hjälpa dig med Optimum OPTIDRILL B 23PRO Bruksanvisning. Jag har noggrant granskat dokumentet och kan hjälpa dig att hitta den exakta information du behöver eller förklara innehållet på ett tydligt och enkelt sätt. Oavsett om du letar efter vägledning om specifika funktioner, felsökningssteg eller allmän användning, tveka inte att ställa dina frågor. Ju mer detaljer du ger om dina bekymmer eller behov, desto mer exakt och effektivt kan jag hjälpa dig!

Assistent skriver

Assistenten är inte tillgänglig. Försök igen senare.

Annons

Operating manual

Bench drilling machine

Upright drilling machine

Table of contents

Preface

1 Safety

Master Labels

1.1

Safety instructions (warning notes)

1.1.1 Classification of hazards

1.1.2 Other pictograms

1.2

Intended use

1.3

Reasonably foreseeable misuse

1.3.1 Avoiding misuses

1.4

Possible dangers caused by the drilling machine

1.5

Qualification of the staff

1.5.1 Target group

1.5.2 Authorized staff

1.6

Operator positions

1.7

Safety measures during operation

1.8

Safety devices

1.9

EMERGENCY-STOP push button

1.10

Separating protective devices

1.10.1 Covering cap of the pulley

1.10.2 Drill chuck protection

1.11

Drilling table

1.12

Prohibition, warning and mandatory signs

1.13

Safety check

1.14

Individual protection gear

1.15

Safety during operation

1.16

Safety during maintenance

1.16.1 Disconnecting and securing the drilling machine

1.16.2 Using lifting equipment

1.16.3 Mechanical maintenance work

1.17

Accident report

1.18

Electrical system

2 Technical data

2.1

Electrical connection

2.2

Power drive motor

2.3

Drilling capacity in steel S235JR

2.4

Continuous drilling capacity in steel S235JR

2.5

Spindle seat

2.6

T-slots - size

2.7

Table size

2.8

Spindle stroke

2.9

Throat depth

2.10

Machine height

2.11

Column diameter

2.12

Distance spindle - table

2.13

Distance spindle - stand