XYR 6000 Wireless Temperature/Discrete Input Transmitter Series

XYR 6000 Wireless Temperature/Discrete Input Transmitter Series
XYR 6000 Wireless Temperature/Discrete
Input Transmitter
Series 400 Specifications
34-XY-03-29 December 2010
Introduction
Building upon the tremendously successful ST 3000
series transmitter line; Honeywell brings simple, safe, and
secure wireless technology to its measurement portfolio
STTW820, 830, 840 with direct mounted T/C or RTD
STTW401 with inputs for T/C’s (3 max), RTD’s (2 max) and/or
discrete inputs (3 max)
in the XYR 6000 Series Wireless Transmitters.
The XYR 6000 series measurements are part of the
Honeywell OneWireless system and are ISA100.11a
Compliant.
Measurement and information without wires! The XYR
6000 wireless transmitters series enable customers to
obtain data and create information from remote and
hazardous measurement locations without the need to
run wires, where running wire is cost prohibitive and/or
the measurement is in a hazardous location. Without
wires, transmitters can be installed and operational in
minutes, quickly providing information back to your
system.
XYR 6000 wireless transmitters send information to an
ISA.11a compliant MESH infrastructure. Wireless Data
Managers (WDM) provide the path to bring that
information into Experion PKS or any other control
Figure 1 — XYR 6000 Temperature/DI Transmitters
system wirelessly via OPC client or Modbus-TCP.
Implement the value of wireless technology today:

Measure remote access points simply, safely and
securely
Transmitter power is supplied by two “D” size lithium

Obtain and utilize previously inaccessible information
due to high wiring cost or hazardous locations.

Easily meet regulatory requirements

Improve process efficiency

Enhance Flexibility to monitor applications:
batteries in an Intrinsically Safe module with an expected
lifetime of up to ten years. Transmitter range with the
integral antenna is 1000’ (305 m) under ideal conditions.
The temperature/discrete input transmitter can support a
combination of thermocouple inputs, RTD inputs and
- that have no access to power
Discrete inputs. The temperature transmitter will
- that are remote or difficult to reach
simultaneously support an integral probe and external
- that may require frequent reconfiguration
inputs. When the integral probe is a thermocouple, then
two external thermocouples or one external RTD can be
wired to the transmitter. (See Figure 2)
- where manual readings have been required
previously.
XYR 6000 Wireless Temperature/Discrete Input Transmitter
2
Specifications
Operating Conditions
Parameter
Reference
Condition
(at zero
static)
°C
°F
Ambient Temperature**
Humidity
25 ±1
%RH
77 ±2
Rated Condition
°C
-40 to 85*
10 to 55
77 ±2
°F
-40 to 185*
0 to 100
Ambient Temperature
LCD Display visible range
25 ±1
Vibration
Maximum of 4g over 15 to 200Hz
Shock
Maximum of 40g
Operative Limits
°C
°F
-40 to 85*
Transportation
and Storage
°C
°F
-40 to 185* -40 to 85
0 to 100
-40 to 185
0 to 100
-20 to 70°C
-4 to 158°F
Battery powered 3.6V Lithium thionyl chloride (LiSOCl2) batteries non rechargeable, size D
Power
24VDC Wired Power (option) - For I.S. Application: 21 V to 25 Vdc Operated with
MTL7728P+ barrier (252 Ohms Max. end to end resistance), Max input current 26mA.
For Non I.S. application: 11 V to 30 Vdc Input range, Max input current 100mA.
*24V power option rated 80°C (176°F)
** The Ambient Limits shown are for Ordinary Non-Hazardous locations only. Refer to the appropriate Control Drawing, FM/CSA, ATEX, or
IECEx for the Ambient Limits when installed in Hazardous Locations.
Wireless Specifications
Parameter
Description
Wireless Communication
2,400 to 2,483.5 MHz (2.4 GHz) Industrial, Scientific and Medical (ISM) band
FHSS Selection – Frequency Hopping Spread Spectrum
DSSS Selection – Direct Sequential Spread Spectrum per FCC 15.247 / IEEE 802.15.4–
2006.
ISA100.11a Compliant (2.4 GHz Direct Sequence Spread Spectrum 802.15.4 DSSS-FH).
Every data packet transmitted in either direction is verified (CRC check) and acknowledged
by the receiving device.
USA – FCC Certified
Canada – IC Certified
European Union – RTTE/ETSI Conformity
Japan – Ministry of Internal Affairs and Communications Certified (DSSS Selection only)
ISA100.11a RF
NA Selection – 125 mW (20.9 dBm) maximum transmit power not including antenna per
Transmitter Power
FCC/IC, or 400 mW (26.0 dBm) maximum EIRP including antenna for USA and Canadian
locations.
(Optional)
EU Selection – 10 mW (10.0 dBm) maximum EIRP including antenna per RTTE/ETSI for
EU locations.
FHSS RF Transmitter
Power (Optional)
NA Selection – 125 mW (20.9 dBm) maximum transmit power not including antenna per
FCC/IC, or 400 mW (26.0 dBm) maximum EIRP including antenna for USA and Canadian
locations.
EU Selection – 100 mW (20.0 dBm) maximum EIRP including antenna per RTTE/ETSI for
EU locations.
XYR 6000 Wireless Temperature/Discrete Input Transmitter
3
Parameter
Description
DSSS RF Transmitter
Power (Optional)
NA Selection – 125 mW (20.9 dBm) maximum transmit power not including antenna per
FCC/IC, or 400 mW (26.0 dBm) maximum EIRP including antenna for USA and Canadian
locations.
EU Selection – 10 mW (10.0 dBm) maximum EIRP including antenna per RTTE/ETSI for
EU locations.
JP Selection – 12.14 dBm/MHz [32mW (15.14 dbm)] maximum EIRP including antenna for
Japanese locations.
Data
PV Publish Cycle Time: Configurable as 1, 5, 10 or 30 seconds
Rate: 250 Kbps
Antennas
Integral – 2 dBi omnidirectional monopole
Integral – 4 dBi omnidirectional monopole
Remote – 8 dBi omnidirectional monopole with up to 20 m cable and lightning surge
arrester.
Remote – 14 dBi directional parabolic with up to 20 m cable and lightning surge arrester.
Signal Range
Nominal 305 m (1,000 feet) between Field Transmitter and Infrastructure Unit (Multinode)
or Gateway Unit when using 2 dBi Integral antenna with a clear line of sight.*
Routing vs Non-Routing
Unit can be set as a Field Routing or non-Field Routing device; the number of routing
devices is set by the system manager.
Using the device as a routing device will impact battery life, the more messages routed
through a device, the greater the impact on battery life.
* Actual range will vary depending on antennas, cables and site topography.
Remote antenna cables
XYR 6000 Wireless Temperature/Discrete Input Transmitter
4
Remote Antennas
4 dBi Omnidirectional Antenna
8 dBi Omnidirectional Antenna
14 dBi Directional Antenna
Performance under Rated Conditions
Parameter
Description
Accuracy
±0.10% of range in mV at reference conditions for linear inputs and RTDs
Temperature Effects
±0.01% of full scale per °C
Stability
±0.10% of URL per year
Stray Rejection
Common Mode (50 or 60 Hz): 120 dB
Normal Mode (50 or 60 Hz): 40 dB
Maximum Lead Wire Resistance
50 ohms/leg for all analog input types
Discrete Input
Single SPST dry contacts. To maintain I.S. ratings, contacts must be limited to
simple switches only.
Maximum "ON" contact resistance of 300 Ohms
Minimum "OFF" contact resistance of 100K Ohms
Resistances must include all field wiring.
Cold Junction Accuracy
±0.5°C
Lightning Surge Arrester (Remote
antenna only)
Frequency range: 0 – 3 GHz, 50 Ohms, VSWR = 1:1.3 Max, Insertion Loss = 0.4 dB
Connectors Type N Female, Max, Gas Tube Element: 90 V ± 20%, Impulse Breakdown
Voltage = 1,000 V ± 20%, Maximum Withstand Current = 5 KA.
CE Conformity
These transmitters are in conformity with the protection requirements of European
Council Directives: 89/336/EEC, the EMC Directive and 1999/5/EC, the
Telecommunications Directive per EN 300 328, V1.6.1 (2004-11), EN 300 489-1,
V1.6.1 (2005-09), EN 300 489-3, V1.4.1 (2002-08) and EN 61326-1997+A1+A2,
Electrical Equipment for Measurement, Control and Laboratory Use – EMC
Requirements.
Hazardous Location Certifications

See the Model Selection Guide on page 11.
Performance specifications are based on reference conditions of 25°C (77°F), zero (0) static pressure, and 10 to 55% RH.
XYR 6000 Wireless Temperature/Discrete Input Transmitter
5
Physical Specifications
Parameter
Description
Mounting Bracket
Carbon Steel (Zinc-plated) or Stainless Steel angle bracket or Carbon Steel flat bracket
available (standard options).
Terminal Assembly wiring
gauge range
28 to 16
Electronic Housing
Epoxy-Polyester hybrid paint. Low Copper-Aluminum. Meets NEMA 4X (hosedown and
corrosion resistant), IP 66/67 (hosedown and submersible to 1m).
Stainless Steel Housing (option) 316 SS Electronics Housing - with M20 Conduit Connections
316 SS Housing with 1/2" NPT Conduit Connection
316 SS or Grade CF8M, the casting equivalent of 316 SS with M20 or 1/2" NPT Conduit
Connection.
If ordered with the Remote Antenna options, the antenna parts are not SS or Marine type
cables; the integral antenna uses SS parts.
Mounting
Can be mounted in virtually any position using the standard mounting bracket. Mounting
should result in the antenna being vertically oriented. Bracket is designed to mount on 2inch (50 mm) vertical or horizontal pipe. See Figure 4.
Dimensions
See Figure 5.
Net Weight
Approximately 9 pounds (4.1 Kg)
ISA100.11a Compliant Inputs
The input channels can be configured for the following input types by using the OneWireless User Interface with the
corresponding device descriptor file:
XYR 6000 Wireless Temperature/Discrete Input Transmitter
6
Selecting any RTD/Ohm input renders Channel 3's input terminals unavailable and it's PV and status invalid. Channel 3
should be set to Out of Service when using an RTD or Ohm input.
The transmitter measures the analog signal from temperature sensors, discrete inputs, millivolt values or ohm values and
transmits a digital output signal proportional to the measured value for direct digital communications with systems.
The discrete input channels support voltage-free floating contacts. Maximum ON contact resistance is 300 ohms. Minimum
OFF contact resistance is 5000 ohms.
The Process Variable (PV) is available for monitoring and alarm purposes. The cold junction temperature is also available as
a fourth channel PV. Available PV update rates are 1, 5, 10, 30 seconds and are set using the Wireless Builder. Slower
update rates extend battery life.
Input Types and Ranges
Input Type
Range Deg.F
Range Deg.C
Pt100 RTD (alpha 0.00385)
-300 to +1200
-184 to +649
Pt200 RTD
-300 to +1200
-184 to +649
Pt500 RTD
-300 to +1200
-184 to +649
Type B T/C
0 to 3300
-18 to +1816
Type E T/C
-454 to +1832
-270 to +1000
Type J T/C
0 to 1600
-18 to + 871
Type K T/C
0 to 2400
-18 to +1816
Type N T/C
0 to 2372
-18 to +1300
Type R T/C
0 to 3100
-18 to +1704
Type S T/C
0 to 3100
-18 to +1704
Type T T/C
-300 to +700
-184 to +371
Millivolts
0 to 10
0 to 50
0 to 100
Resistance (Ohms)
0 to 100Ω
0 to 200Ω
0 to 500Ω
0 to 1000Ω
XYR 6000 Wireless Temperature/Discrete Input Transmitter
7
3 T/Cs
1 T/C & 1 RTD
+
1
4
+
+
1
4
–
2
5
–
–
2
5
3
6
3
6
+
–
2 RTDs
1 RTD & 1 T/C
1
4
1
4
+
2
5
2
5
–
3
6
3
6
Figure 2 — XYR6000 Temperature Transmitter Field Wiring
XYR6000 Temperature Transmitter Field Wiring for Discrete Inputs
THREE THERMOCOUPLE
CONNECTION
T/C or mV
(PV1)
1
TB1
TB2
4
2
5
3
6
T/C or mV
(PV2)
T/C or mV
(PV3)
2 JUMPER WIRES
ONLY ONE T/C MAY BE GROUNDED TYPE
XYR 6000 Wireless Temperature/Discrete Input Transmitter
Figure 3 — XYR 6000 Temperature Transmitter Field Wiring for Discrete Inputs
8
XYR 6000 Wireless Temperature/Discrete Input Transmitter
Figure 4 — Examples of typical mounting positions
Figure 5 — Typical mounting dimensions for reference.
9
XYR 6000 Wireless Temperature/Discrete Input Transmitter
Options
Mounting Bracket
The angle mounting bracket is available in either zinc-
10
Tagging (Option TG)
Up to 30 characters can be added on the stainless steel
nameplate mounted on the transmitter’s electronics
plated carbon steel or stainless steel and is suitable for
housing at no extra cost. A stainless steel wired on tag
horizontal or vertical mounting on a two inch (50
with additional data of up to 4 lines of 28 characters is
millimeter) pipe, as well as wall mounting. An optional flat
also available. The number of characters for tagging
mounting bracket is also available in carbon steel for two
includes spaces.
inch (50 millimeter) pipe mounting.
Transmitter Configuration
All configurable parameters are accessible via the
OneWireless network via READ/WRITE transactions.
XYR 6000 Wireless Temperature/Discrete Input Transmitter
Model Selection Guides are subject to change and are inserted into the specifications as guidance only.
Prior to specifying or ordering a model check for the latest revision Model Selection Guides which are published at:
http://hpsweb.honeywell.com/Cultures/en-US/Products/Instrumentation/ProductModelSelectionGuides/default.htm
Model Selection Guide (34-XY-16-46)
11
XYR 6000 Wireless Temperature/Discrete Input Transmitter
12
XYR 6000 Wireless Temperature/Discrete Input Transmitter
13
XYR 6000 Wireless Temperature/Discrete Input Transmitter
OneWireless and XYR are trademarks and Experion is a registered trademark of Honeywell International Inc.
Specifications are subject to change without notice
14
XYR 6000 Wireless Temperature/Discrete Input Transmitter
For More Information
Learn more about how Honeywell’s Wireless
Temperature Transmitters can provide simple, safe,
and secure wireless technology, visit our website
www.honeywell.com/ps/hfs or contact your
Honeywell account manager.
Honeywell Process Solutions
1860 West Rose Garden Lane
Phoenix, Arizona 85027
Tel: 1-800-423-9883 or 1-800-343-0228
www.honeywell.com/ps
34-XY-03-29
December 2010
© 2011 Honeywell International Inc.
15
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement