Aruba AP-60/61 Access Points
Aruba AP-60/61
Access Point
Installation Guide
Copyright
© 2008 Aruba Networks, Inc. AirWave®, Aruba Networks®, Aruba Mobility
Management System®, Bluescanner, For Wireless That Works®, Mobile Edge
Architecture, People Move. Networks Must Follow., RFProtect, The All Wireless
Workplace Is Now Open For Business, and The Mobile Edge Company® are
trademarks of Aruba Networks, Inc. All rights reserved. All other trademarks are
the property of their respective owners.
Open Source Code
Certain Aruba products include Open Source software code developed by third
parties, including software code subject to the GNU General Public License
("GPL"), GNU Lesser General Public License ("LGPL"), or other Open Source
Licenses. The Open Source code used can be found at this site:
http://www.arubanetworks.com/open_source
Legal Notice
The use of Aruba Networks, Inc. switching platforms and software, by all
individuals or corporations, to terminate other vendors’ VPN client devices
constitutes complete acceptance of liability by that individual or corporation for
this action and indemnifies, in full, Aruba Networks, Inc. from any and all legal
actions that might be taken against it with respect to infringement of copyright on
behalf of those vendors.
Warranty
This hardware product is protected by the standard Aruba warranty of one year
parts/labor. For more information, refer to the ARUBACARE SERVICE AND
SUPPORT TERMS AND CONDITIONS.
Altering this device (such as painting it) voids the warranty.
ii
Aruba AP-60/61
Installation Guide
0510160-03
April 2008
Contents
Chapter 1
Chapter 2
Appendix A
Appendix B
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Back View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The Aruba AP Setup Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
2
5
6
AP Deployment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Mounting the Aruba AP-60/61 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Aruba AP-60 Detachable Antennas . . . . . . . . . . . . . . . . . . . . . . . . 8
Free-Standing Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Using the Built-In Mounting Slots . . . . . . . . . . . . . . . . . . . . . . . . . 12
Using the Optional Mounting Kits . . . . . . . . . . . . . . . . . . . . . . . . . 13
Connecting Required Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Selecting an FE Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Connecting Cables & Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Selecting an Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Port Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FE Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial Breakout Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DB-9 Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
“To AP” Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
“To Network” Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
United States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17
Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Japan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Europe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Certifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Product Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Product Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ethernet Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Radio Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Over Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21
Aruba AP-60/61
Installation Guide
17
18
18
19
19
21
21
22
23
23
25
26
26
26
26
27
iii
Contents
Chapter
Physical Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Optional Items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Aruba AP-60 Access Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Aruba AP-61 Access Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Related Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contacting Aruba Networks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Proper Disposal of Aruba Equipment . . . . . . . . . . . . . . . . . . . . . . . .
China RoHS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
iv
Aruba AP-60/61
Installation Guide
27
27
27
28
33
37
38
38
39
0510160-03
April 2008
1
Introduction
The Aruba AP-60/61 is part of a comprehensive wireless network solution. The
device works in conjunction with the Aruba Mobility Controller and can act as a
wireless access point or air monitor.
As a wireless Access Point (AP), the Aruba AP-60/61 provides transparent,
secure, high-speed data communications between wireless network devices
(fixed, portable, or mobile computers with IEEE 802.11a or IEEE 802.11b/g
wireless adapters) and the wired LAN.
As a wireless Air Monitor (AM), a feature unique to Aruba products, the Aruba
AP-60/61 enhances wireless networks by collecting statistics, monitoring traffic,
detecting intrusions, enforcing security policies, balancing wireless traffic load,
self-healing coverage gaps, and more.
NOTE:
Service to all Aruba Networks equipment must be performed by trained
service personnel only.
Aruba AP-60/61
Installation Guide
1
Introduction
Chapter 1
Front View
A
A
B
C
1
B
2
3
4
5
FIGURE 1-1
1
Aruba AP-60/61 Front View
Antenna fixtures for Wireless Communications
Depending on the model, the AP will have one of the following:
2
Aruba AP-60/61
Installation Guide
0510160-03
April 2008
Introduction
Chapter 1
A
Aruba AP-60–Two Reverse Polarity SMA (RP-SMA) connectors for attaching
separate antennas (not included). For details, see “Aruba AP-60 Detachable
Antennas” on page 8. (The AP-60 requires that both connectors be used in
ArubaOS 2.2 releases or lower. Single antenna operation is supported with
ArubaOS 2.3 or higher.)
NOTE:
B
2
When facing the AP-60 as shown in Figure 1-1, the antenna
connector on the left is for antenna 1, and the connector on the right
is for antenna 2 in a diversity configuration.
Aruba AP-61–Built-in swivel array with dual, tri-band, omnidirectional
antennas.
Indicator LEDs
During operation, the Aruba AP-60/61 LEDs provide the following information:
TABLE 1-1
LED
A
B
C
PWR
ENET
WLAN
NOTE:
3
Aruba AP-60/61 LEDs
State
Description
Off
The device is off - no power.
Green-Solid
The device is powered and operating.
Off
No link on the FE port. No connection to the
network.
Green-Solid
Ethernet link detected on the FE port.
Green-Flashing
Transmitting or receiving data across the FE
port. Flashing rate is proportional to network
activity.
Off
The wireless interface is disabled or down.
Green-Solid
The wireless interface is enabled and
functioning as an Access Point.
Green-Flashing
The wireless interface is enabled and
functioning as an Air Monitor.
LEDs on the Mobility Controller provide additional status and security
information about connected APs.See the ArubaOS User Guide for more
information.
Air Vents
These vents promote proper air circulation for cooling the device. Do not allow
these vents to be obstructed by mounting equipment, network cables, or any
other material.
Aruba AP-60/61
Installation Guide
3
Introduction
Chapter 1
4
FE Port
This port attaches the Aruba AP-60/61 to a 10Base-T/100Base-TX (twisted-pair)
Ethernet LAN segment. This port also supports Serial and Power Over Ethernet
(SPOE).
See Appendix 4, “Product Specifications.” for port and cable specifications.
5
DC Power Socket
This socket is used to connect the optional AC power adapter (not included). If
POE is being used to supply power to the Aruba AP-60/61, the power adapter is
not necessary.
4
Aruba AP-60/61
Installation Guide
0510160-03
April 2008
Introduction
Chapter 1
Back View
1
2
3
4
FIGURE 1-2
1
Aruba AP-60/61 Back View
Mounting Slots
The keyhole-shaped slots on the back of the chassis are used for mounting the
Aruba AP-60/61.
2
Air Vents
These vents promote proper air circulation for cooling the device. Do not allow
these vents to be obstructed by mounting equipment, network cables, or any
other material.
Aruba AP-60/61
Installation Guide
5
Introduction
Chapter 1
3
Fold-Out Stand
This fold-out stand allows the Aruba AP-60/61 to be stood upright on a table or
shelf.
4
Kensington Security Slot
This slot is compatible with a Kensington MicroSaver Security Cable (not
included) which can be used to prevent the unauthorized removal of the Aruba
AP-60/61 from its installed location. To secure the Aruba AP-60/61, wrap a
security cable around an immovable object, insert the cable’s lock into the
Kensington Security Slot, and turn the key.
NOTE:
The serial number and model number are on the bottom of the unit.
The Aruba AP Setup Process
Setting up an Aruba AP typically consists of four stages:
WLAN Planning—The administrator determines how many Aruba APs will be
needed for their wireless network strategy and where they will be deployed. This
can be easily accomplished using Aruba’s automated RF Plan site-survey
software (available separately).
AP Provisioning—Provisioning provides each Aruba AP with initial settings that
allow it to locate the host Aruba Mobility Controller. Depending on the network
topology and services, AP provisioning can be performed manually for each AP or
plug-and-play for batches of APs.
AP provisioning is discussed in Appendix 2, “Provisioning Access Points.”
AP Deployment—Once provisioned, the AP can be physically installed at its
intended place of operation.
AP deployment is covered in Chapter 2, “AP Deployment”.
AP Configuration—The administrator defines the operational behavior for each
Aruba AP, such as RF characteristics and security features.
For AP configuration information, refer to the ArubaOS User Guide.
6
Aruba AP-60/61
Installation Guide
0510160-03
April 2008
2
AP Deployment
This chapter covers the following topics:
z
z
Physical mounting of the Aruba AP-60/61
Connecting the required cables
Mounting the Aruba AP-60/61
When provisioning is complete, mount the Aruba AP-60/61 at its intended service
location.
The Aruba AP-60/61 Access Points with or without external antennas are
intended only for installation in Environment A as defined in IEEE 802.3.af. All
interconnected equipment must be contained within the same building, including
the interconnected equipment's associated LAN connections. (When using an
external antenna, 5.150 to 5.250 MHz are blocked.)
Select a location as close as possible to the center of the intended coverage area.
If necessary, use the Aruba RF Plan site survey tool to determine the optimum
locations for your access points and air monitors.
The service location should be free from obstructions or obvious sources of
interference. Normally, the higher you place an access point or air monitor, the
better its performance.
If external antennas are used, make sure that they and their associated wiring are
located entirely indoors. The Aruba AP-60/61 and any optional external antennas
are not suitable for outside use.
Aruba AP-60/61
Installation Guide
7
AP Deployment
Chapter 2
The Aruba AP-60/61 can be mounted on a wall or suspended from above (not
shown) using one of the optional mounting kits (dimensions vary) in the
following ways:
1
FIGURE 2-1
NOTE:
2
3
Aruba AP-60/61 Mounting Options
For dimensions, see Appendix 4, “Product Specifications”. Allow 5
cm (2") additional space on the right-hand side for cables.
Measurements for the Aruba AP-60 depend on attached antennas,
which vary.
Aruba AP-60 Detachable Antennas
Before deploying the Aruba AP-60, attach the appropriate antennas (not
included). The antenna connections should be tightened by hand to avoid
overtightening.
The Aruba AP-60 has dual Reverse Polarity SMA (RP-SMA) antenna connectors
that accept a variety of high-gain detachable antennas. See Table 2-1 for the list
of FCC approved antennas tested for use with the Aruba AP-60.
Make sure that all external antennas and their associated wiring are located
entirely indoors. The Aruba AP-60 Access Points and their optional external
antennas are not suitable for outside use.
8
Aruba AP-60/61
Installation Guide
0510160-03
April 2008
AP Deployment
Chapter 2
FCC-Approved Detachable Antennas
Table 3-1 lists the antennas that are approved for use with the Aruba AP-60.
TABLE 2-1
Aruba Part #
FCC-Approved Detachable Antennas
Description
Gain
dbi
Manufacturer
Man. Part #
5
Nearson
T614AH-2.4
5/5.X-S
MULTI-BAND ANTENNA
AP-ANT-1
Tri-Band,
High-Gain,
Omni-Directional
Antenna (Indoor)
(Swivel Connector)
2.4Ghz (802.11B/G)
AP-ANT-2
High-Gain,
Omni-Directional
Cylindrical (Indoor)
with RP-SMA
Connector
6
Centurion
IG2450-RPS
MA
AP-ANT-3
High-Gain,
Bi-Directional
Patch Antenna
(Indoor) with
RP-SMA
Connector
5
Centurion
IB2450-RPS
MA
AP-ANT-4
High-Gain,
Directional Patch
Antenna (Indoor)
with RP-SMA
Connector
9
Centurion
ID240-RPSM
A/CAF94379
AP-ANT-5
Down-Tilt,
Omni-Directional
Patch Antenna
(Indoor) with
RP-SMA
Connector
3.5
Cushcraft
SQ2403PG3
6RSM
AP-ANT-7
High-Gain
Directional Patch
Antenna (Indoor /
Outdoor) with
RP-SMA
Connector
11.5
HD Comms.
Corp
PCW24-080
12-AFL/HD1
9656
Aruba AP-60/61
Installation Guide
9
AP Deployment
Chapter 2
TABLE 2-1
FCC-Approved Detachable Antennas (Continued)
AP-ANT-8
High-Gain,
Omni-Directional
Cylindrical (Indoor /
Outdoor) with
RP-SMA
Connector
5
Cushcraft
S2403BPX3
6RSM
AP-ANT-10
High-Gain,
Omni-Directional
Cylindrical (Indoor /
Outdoor) with
RP-SMA
Connector
5.5
Cushcraft
S5153WBPX
36RSM
AP-ANT-11
Down-Tilt,
Omni-Directional
Patch Antenna
(Indoor) with
RP-SMA
Connector
3.5
Cushcraft
SQ5153WP3
6RSM
AP-ANT-12
High-Gain,
Directional Patch
Antenna (Indoor /
Outdoor) with
RP-SMA
Connector
14
Cushcraft
S52514WP3
6RSM
5Ghz (802.11A)
10
Aruba AP-60/61
Installation Guide
0510160-03
April 2008
AP Deployment
Chapter 2
Free-Standing Placement
To place the Aruba AP-60/61 indoors on a flat table or shelf:
Flip open the stand located on the back of the Aruba AP-60/61:
FIGURE 2-2
Aruba AP-60/61Fold-Out Stand
Place the device on a sturdy table or shelf.
CAUTION:
Do not place the Aruba AP-60/61 in any place where it
could fall on people or equipment. For more secure
installation, use one of the optional mounting kits.
Orient the antennas.
For best performance, swivel the individual antennas (Aruba AP-60) or antenna
array (Aruba AP-61) so that they are oriented vertically. Once mounting is
complete, connect the required cables (see instructions on page 14).
Aruba AP-60/61
Installation Guide
11
AP Deployment
Chapter 2
Using the Built-In Mounting Slots
The keyhole-shaped slots on the back of the Aruba AP-60/61 can be used to
attach the device upright to an indoor wall or shelf.
CAUTION:
Do not use the mounting slots to hang the Aruba
AP-60/61 from the ceiling, sideways, or in any place
where it could fall on people or equipment. For more
secure installation, use one of the optional mounting kits.
To hang the Aruba AP-60/61 upright using the mounting slots, perform the
following steps.
1.
Install two screws in the wall or shelf as shown in Figure 2-3:
Screw/Nail Positions
(fastened to wall or shelf)
Screw/Nail Dimensions
Maximum
Minimum
7.0 mm
12.7 cm
(5.00")
2.0 mm
3.8 mm
clearance
from surface
5.8 mm
1.3 mm
clearnace
from surface
3.0 mm
0.27"
0.08"
0.15"
clearance
from surface
0.23"
0.05"
clearance
from surface
0.12"
FIGURE 2-3
Mounting Screw Specifications
If attaching the device to drywall, we recommend using appropriate wall
anchors (not included) as shown in Figure 2-4 on page 13.
12
Aruba AP-60/61
Installation Guide
0510160-03
April 2008
AP Deployment
Chapter 2
2.
Align the Aruba AP-60/61 mounting slots to capture the surface screws.
FIGURE 2-4
3.
Hanging the Aruba AP-60/61 on Screws
Secure the Aruba AP-60/61, if desired.
To prevent the unauthorized removal of the Aruba AP-60/61 from its installed
location, use a Kensington MicroSaver Security Cable (not included). Wrap
the security cable around an immovable object, insert the cable’s lock into the
Kensington Security Slot on the back of the Aruba AP-60/61, and turn the
key.
4.
Orient the antennas.
For best performance, swivel the individual antennas (Aruba AP-60) or antenna
array (Aruba AP-61) so that they are oriented vertically (see Figure 2-1 on page 8).
Once mounting is complete, connect the required cables (see instructions on
page 14).
Using the Optional Mounting Kits
Use the optional mounting kit to attach the Aruba AP-60/61 to a wall, shelf, or
ceiling. For installation, see the Aruba AP-60/61 Mounting Kit Installation Notes
(P/N 0500037-01) provided with each kit.
Aruba AP-60/61
Installation Guide
13
AP Deployment
Chapter 2
Connecting Required Cables
The Aruba AP-60/61 Access Points with or without external antennas are
intended only for installation in Environment A as defined in IEEE 802.3.af. All
interconnected equipment must be contained within the same building, including
the interconnected equipment's associated LAN connections.
Selecting an FE Cable
The 10/100 Mbps Ethernet (FE) port is used to connect the AP to a
10Base-T/100Base-TX (twisted-pair) Ethernet LAN segment. The appropriate FE
cable depends on the features required of the FE port:
z
SPOE
When connecting the AP to a device that supports Serial and Power Over
Ethernet (SPOE), use an 8-conductor, Category 5 UTP, straight-through FE
cable.
The Aruba 5000 (with Line Card LC-5000-24FE-2GE-SPOE), the Aruba 2400,
and the Aruba 800 support SPOE.
z
POE
If the connecting device supports only Power Over Ethernet (POE), use a 4- or
8-conductor, Category 5 UTP, straight-through FE cable.
z
Network Only
If the connecting device does not support POE, use a 4- or 8-conductor,
Category 5 UTP, FE cable. The port detects MDI/MDX and automatically
adjusts for straight-through or crossover cables.
The maximum length for FE cables is 100 meters (325 feet).
When the Aruba AP-60/61 is installed in an air-handling space, such as above
suspended ceilings, as described in National Electrical Code (2002) Article
300.22(C), and Canadian Electrical Code, Sections 2-128, 12-010(3) and 12-100,
Part 1, CSA C22.1, POE is required. Also, any FE cable installed in such spaces
should be suitable under NEC Article 800.50 and marked accordingly for use in
plenums and air-handling spaces with regard to smoke propagation, such as
CL2-P, CL3-P, MPP, or CMP.
Use the built-in antenna (for the AP-61). For the Aruba AP-60, use Aruba
AP-ANT-1. For all other antennas, make sure the antenna cable is UL listed and
suitable for use in plenums and air-handling spaces, such as CL2-P, CL3-P, MPP,
or CMP, and mount the antenna outside of the air-handling space.
Install cables in accordance with all applicable local and national regulations and
practices.
For more port and cable details, see Appendix 3, “Port Specifications.”
14
Aruba AP-60/61
Installation Guide
0510160-03
April 2008
AP Deployment
Chapter 2
Connecting Cables & Power
CAUTION:
To prevent personal injury or damage to equipment, be
sure to comply with electrical grounding standards during
all phases of installation and operation of the AP. Do not
allow the Aruba AP-60/61 or its attachments to be
connected to or make contact with metal or power outlets
on a different electrical ground than the device to which it
is connected. Also, never connect the AP or Mobility
Controller to external storm grounding sources.
1.
Connect one end of the FE cable directly to the Aruba AP-60/61 FE port.
2.
Connect the other end of the FE cable to one of the following:
A
To a network port on the Mobility Controller, or
B
To a network hub, router, or switch that has a routable path to the
Mobility Controller.
NOTE:
3.
If the connecting device supplies POE, a straight-through cable must
connect the Aruba AP-60/61 directly to the powering device without any
intervening hubs, routers, or other networking equipment.
Connect power, if necessary.
The Aruba AP-60/61 can receive electrical power using the following options:
z
POE
If connecting the Aruba AP-60/61 to a device that supplies IEEE 802.3af
compliant POE no additional power connection is necessary.
z
Power Outlet
NOTE:
When the Aruba AP-60/61 is installed in an air-handling space, as
described in NEC (2002) Article 300.22(C), POE must be used instead
of a power outlet.
If local regulations and practices permit, connect the optional AC power adapter
(not included) to the DC power socket on the Aruba AP-60/61 and plug it into an
appropriate power outlet.
CAUTION:
To prevent personal injury or damage to equipment,
use only the AC power adapter certified for this device
in the country where it is used.
Aruba AP-60/61
Installation Guide
15
AP Deployment
Chapter 2
Selecting an Antenna
There are three ways to select an AP-60 antenna:
1.
From the AP console (serial or telnet) enter set_antenna 0|1|2 where 0
specifies auto mode, and 1 or 2 chooses a specific antenna. The antenna
selection is not persistent and the AP will loose the antenna selection, if
rebooted.
2.
From the AP boot prompt (apboot>) enter a_antenna 0|1|2 or g_antenna 0|1|2
to specify an antenna. Enter a save command before booting the AP to save
the antenna configuration in the AP’s Flash memory, along with other
provisioning parameters.
3.
For releases 2.3 and higher, you can provision the antenna selection from the
Mobility Controller.
Maintenance
The AP-60 and AP-61 require no maintenance beyond keeping the AP clean and
dust free. To clean the Aruba AP-60/61, use a static-free, dry cloth.
Aruba recommends that these units be inspected annually for damage, dust
buildup, and to verify that all connections are secure.
16
Aruba AP-60/61
Installation Guide
0510160-03
April 2008
B
Port Specifications
FE Port
The 10/100 Mbps Ethernet (FE) port is located on the right-hand side of the Aruba
AP-60/61 and has an RJ-45 female connector. The port pin-outs are shown in
Figure B-1:
Aruba 60/61
10/100 Mbps Ethernet
RJ-45 Female
Pin-Out
1
2
3
4
5
6
7
8
Direction
Input
Output
FIGURE B-1
ETH Tx+
ETH Tx–
ETH Rx+
Serial RxD**
Serial RGND**
ETH Rx–
Serial TxD**
Serial TGND**
(POE negative*)
(POE negative*)
(POE positive*)
(POE positive*)
(POE positive*)
(POE negative*)
*POE optional
**Serial optional
Aruba AP-60/61 FE Port
The appropriate cable depends on the level of connectivity required of the FE port:
z
If the connecting device supports Serial and Power Over Ethernet (SPOE), use
an 8-conductor, Category 5 UTP, straight-through FE cable with a male RJ-45
connector.
The Aruba 5000 (with Line Card LC-5000-24FE-2GE-SPOE), the Aruba 2400,
and the Aruba 800 support SPOE.
z
z
If the connecting device supports only Power Over Ethernet (POE, including
IEEE 802.3af POE as well as “inline” or “midspan” POE devices), use an 8- or
4-conductor, Category 5 UTP, straight-through FE cable with male RJ-45 connectors.
If the connecting device does not support Serial or POE, use a 4- or 8-conductor, Category 5 UTP, FE cable with male RJ-45 connectors. The port detects
MDI/MDX and automatically adjusts for straight-through or crossover cables.
The maximum length for FE cables is 100 meters (325 feet).
When the Aruba AP-60/61 is installed in an air-handling space, as described in
NEC (2002) Article 300.22 (C), POE is required. Also, any FE cable installed in
such spaces should be suitable under NEC Article 800.50 and marked accordingly
for use in plenums and air-handling spaces with regard to smoke propagation,
such as CL2-P, CL3-P, MPP or CMP.
Aruba AP-60/61
Installation Guide
17
Port Specifications
Chapter B
Install cables in accordance with all applicable local regulations and practices.
Serial Breakout Adapter
The optional serial breakout adapter is used to separate the serial
communications lines from the Aruba AP-60/61 FE+SPOE port. This allows the
administrator to connect a local serial console directly to the AP and access the
apboot prompt for manual provisioning.
The serial breakout adapter pin-outs are shown in Figure B-2:
DB-9 Female Pin-Out
9
8
7
6
5
4
3
2
1
Internal Adapter Wiring
SG
Direction
Input
Output
TxD
RxD
To Console
123456789
RJ-45 Male "To AP" Pin-Out
1
2
3
4
5
6
7
8
ETH Rx+
ETH Rx–
ETH Tx+
Serial TxD
Serial TGND
ETH Tx–
Serial RxD
Serial RGND
(POE negative)
(POE negative)
(POE positive)
12345678
"To AP"
(POE positive)
RJ-45 Male "To Network" Pin-Out
1
2
3
4
5
6
7
8
FIGURE B-2
ETH Tx+
ETH Tx–
ETH Rx+
(POE negative)
(POE negative)
(POE positive)
ETH Rx–
(POE positive)
12345678
"To Network"
Aruba Serial Breakout Adapter
DB-9 Specification
The DB-9 connector attaches to the serial port of a console terminal.
Communication settings for the port are specified in Table B-1:
TABLE B-1
18
Console Terminal Settings
Baud Rate
Data Bits
Parity
Stop Bits
Flow Control
9600
8
None
1
None
Aruba AP-60/61
Installation Guide
0510160-03
April 2008
Port Specifications
Chapter B
“To AP” Specifications
The RJ-45 connector labeled “To AP” attaches to the Aruba AP-60/61 FE port
either directly (if the AP is physically available) or indirectly (if the AP is already
deployed).
When connecting indirectly, use a straight-through FE coupler to attach the “To
AP” connector to the FE cable leading directly to the AP’s FE port with no
intervening hubs, routers, or other network equipment. The cable must be
8-conductor, Category 5 UTP, straight-through FE cable with a maximum length of
100 meters (325 feet).
The Aruba AP-60/61 and serial breakout adapter are plenum rated. When is
installed in an air-handling space, as described in NEC (2002) Article 300.22(C),
any connecting FE cable should be suitable under NEC Article 800.50 and marked
accordingly for use in plenums and air-handling spaces with regard to smoke
propagation, such as CL2-P, CL3-P, MPP or CMP.
Install cables in accordance with all applicable local regulations and practices.
“To Network” Specifications
The RJ-45 connector labeled “To Network” attaches to an FE LAN segment. This
connection is optional unless IEEE 802.11af Power Over Ethernet (POE) is used to
power the AP during manual provisioning.
A straight-through FE coupler may be used to attach the “To Network” connector
to a LAN FE cable. The appropriate cable depends on the level of connectivity
required of the FE port:
z
If the connecting device supports IEEE 802.3af Power Over Ethernet (POE),
use a 4- or 8-conductor, Category 5 UTP, straight-through FE cable with male
RJ-45 connectors.
The Aruba 5000 (with Line Card LC-5000-24FE-2GE-SPOE), the Aruba 2400,
and the Aruba 800 support SPOE.
z
Otherwise, use a 4- or 8-conductor, Category 5 UTP, FE cable with male RJ-45
connectors. The port detects MDI/MDX and automatically adjusts for
straight-through or crossover cables.
NOTE:
Only IEEE 802.3af Power Over Ethernet is supported for manual
provisioning. “Inline” or “midspan” POE devices will not work with the
Aruba serial breakout adapter.
The maximum length for FE cables is 100 meters (325 feet).
Aruba AP-60/61
Installation Guide
19
Port Specifications
Chapter B
The Aruba AP-60/61 and serial breakout adapter are plenum rated. When is
installed in an air-handling space, as described in NEC (2002) Article 300.22(C),
the connecting FE cable should be suitable under NEC Article 800.50 and marked
accordingly for use in plenums and air-handling spaces with regard to smoke
propagation, such as CL2-P, CL3-P, MPP or CMP.
Install cables in accordance with all applicable local regulations and practices.
20
Aruba AP-60/61
Installation Guide
0510160-03
April 2008
C
Product Specifications
Compliance
United States
FCC - Class B
„
„
„
„
Aruba AP-60/61
Product Specifications
RF Radiation Exposure Statement
Radio Frequency Interference Requirements
Canada
Cet appareil numérique respecte les limites de bruits radioélectriques applicables
aux appareils numériques de Classe B prescrites dans la norme sur le matériel
brouilleur: “Appareils Numériques,” NMB-003 édictée par le ministère des
Communications.
The use of this device operating either partially or completely outdoors may
require the user to obtain a license for the system according to the Canadian
regulations. For further information, contact your local Industry Canada office.
RSS-210
This device, when operated in the 5150-5250 MHz frequency range, is only for
indoor use.
CAUTION:
High power radars are allocated as primary users (meaning
they have priority) in the 5250-5350 MHz and 5650-5850
MHz frequency ranges, and these radars could cause
interference and/or damage to LE-LAN devices.
RSS-Gen
This device has been designed to operate with the antennas listed at Table 2-1 on
page 9, and having a maximum gain of 15.0 dBi for 2.4 GHz and 14.0 dBi for 5
GHz. Antennas not included in this list or having a gain greater than 15.0 dBi for
2.4 GHz and 14.0 dBi for 5 GHz are strictly prohibited for use with this device. The
required antenna impedance is 50 Ohms.
Aruba AP-60/61
Product Specifications
Chapter C
To reduce potential radio interference to other users, the antenna type and its gain
should be so chosen that the equivalent isotropically radiated power (EIRP) is not
more than that permitted for successful communication.
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Japan
Indoor Restriction for 5GHz Frequency Range
VCCI - Class B
Europe
WARNING: This is a Class B product. In a domestic environment, this
product may cause radio interference in which case the user may be
required to take adequate measures.
This product complies with Directive 1999/5/EC as well as with EN55022 Class B
and EN55024 standards.
Underwriter Labs
These products have been Listed and tested for fire resistant and
low-smoke-producing characteristics, and are suitable for use in environmental air
space, such as above suspended ceilings, in accordance with Section 300-22(C)
of the National Electrical Code, and Sections 2-128, 12-010(3) and 12-100 of the
Canadian Electrical Code, Part 1, CSA C22.1.
Aruba AP-60/61
Installation Guide
23
Product Specifications
Chapter C
Peut être utilisé dans des gaines transportant de l’air traité, conformément à la
section 300-22(c) du National Electrical Code et aux articles 2-128, 12-010(3) et
12-100 du Code Canadien de l’électricité, Première partie, CSA C22.1.
EMC Compliance and Warning Statement
This equipment has been tested and found to comply with the limits of the
standard for medical devices, IEC 60601-1-2:2001. The unit also complies with
the requirements of EN 60601-1-2:1998, providing the presumption of
compliance to the European Union’s Medical Device Directive 93/42/EEC. The
limits are designed to provide reasonable protection against harmful interference
in a typical medical installation. This equipment generates, uses and can radiate
radio frequency energy, and, if not installed and used in accordance with the
manufacturer’s instructions may cause harmful interference to other devices in
the vicinity. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment causes interference with other devices,
which may be determined by turning the equipment off and on, the user is
encouraged to try and correct the interference by one or more of the following
measures:
„
Reorient or relocate the device receiving the interference.
„
Increase the separation between the equipment.
„
Connect the equipment into an outlet on a circuit different from that to which
the other device(s) are connected.
„
Consult the manufacturer or field service technician for help.
Aruba Networks provides a multi-language document containing country specific
restrictions, additional safety and regulatory information for the enclosed Access
Point. You may find this reference on our website at:
www.arubanetworks.com/safety_addendum
24
Aruba AP-60/61
Installation Guide
0510160-03
April 2008
Product Specifications
Chapter C
Certifications
Item
Measurement
Electromagnetic
Compatibility
FCC Part 15 Class B, FCC Part 15 Class C
(15.207/15.247)
FCC Part 15 Class E 15.407
RSS 210 (CAN)
ICES-003 Class B
VCCI Class B
TELEC ARIB STD-T66
AS/NZS 3548 Class B
EN 61000-3, EN 61000-4-2, EN 61000-4-3,
EN 61000-4-4, EN 61000-4-5, EN 61000-4-6,
EN 61000-4-8, EN 61000-4-11, EN 55022, EN 55024
IEC 60601-1-2:2001(AP 60)
EN 60601-1-2:2001 (AP 60)
The CE approval mark on back of the
product indicates that it meets
European Directives 73/23/EEC and
89/336/EEC
R&TTE Directive:
EN 300 328, EN 301 489, EN 301 893
Medical:
EN 60601-1-2
Safety
UL Listed (UL60950)
UL Listed (Canadian Electrical Code/CSA 22.2 No.
60950)
EN60950 / IEC60950
National Electrical Code Section 300-22(C)
Canadian Electrical Code, Part 1, CSA C22.1 Sections
2-128, 12-010(3), and 12-100
IEC 60601-1:1988 and Amendments 1 and 2
EN 60601-1-1:2001
UL 2043
Aruba AP-60/61
Installation Guide
25
Product Specifications
Chapter C
Product Label
The product label is affixed to the chassis of the Aruba AP 60/61 The symbols on
the label are explained in this chapter.
Product Features
z
z
Wireless dual-band transceiver
Varied antenna options:
z
The Aruba AP-60 has dual Reverse Polarity SMA (RP-SMA) antenna
connectors that accept a variety of high-gain detachable antennas (not
included).
z
z
z
z
z
z
z
The Aruba AP-61 has a built-in swivel array with dual, tri-band,
omnidirectional antennas for reception diversity.
Protocol-independent networking functionality
Supports IEEE 802.11a or IEEE 802.11b/g operation as an AP
Supports IEEE 802.11a and IEEE 802.11b/g operation as an AM
Compatible with IEEE 802.3af Power Over Ethernet (POE)
Seamless connectivity to wired LANs augment existing networks quickly and
easily
Can be centrally managed, configured, and upgraded through the Mobility
Controller to take advantage of network changes and security improvements
Ethernet Compatibility
The Aruba AP-60/61 attaches to 10/100 Mbps Ethernet (FE) LAN segments that
utilize 10Base-T/100Base-TX (twisted-pair) wiring. The device appears as an
Ethernet node and performs a routing function by moving packets between the
wired LAN and remote workstations on the wireless infrastructure.
Radio Characteristics
The Aruba AP-60/61 can be configured to support IEEE 802.11a or IEEE
802.11b/g operation as an AP, and supports both IEEE 802.11a and IEEE
802.11b/g operation as an AM:
z
802.11a provides a high data rate and reliable wireless connectivity
802.11a operation uses a radio modulation technique known as Orthogonal
Frequency Division Multiplexing (OFDM), and a shared collision domain
(CSMA/CA). It operates in the 5GHz Unlicensed National Information
Infrastructure (UNII) band. Data is transmitted over a half-duplex radio channel
operating at up to 54 Megabits per second (Mbps).
z
26
802.11b provides an alternative to wired LANs that can dramatically cut costs
Aruba AP-60/61
Installation Guide
0510160-03
April 2008
Product Specifications
Chapter C
802.11b operation uses the IEEE 802.11 High-Rate Direct Sequence (HRDS)
specification, and a shared collision domain (CSMA/CA). It operates in the
2.4GHz Industrial/Scientific/Medical (ISM) band. The ISM band is available
worldwide for unlicensed use. Data is transmitted at speeds of up to 11
Mbps.
z
802.11g provides a high data rate and is backwards compatible with 802.11b.
802.11g operation uses ODFM and a shared collision domain (CSMA/CA). It
operates in the 2.4GHz Industrial/Scientific/Medical (ISM) band. The ISM band
is available worldwide for unlicensed use. Data is transmitted at speeds of up
to 54 Mbps.
Power Over Ethernet
The Aruba AP-60/61 supports the IEEE 802.3af standard for Power Over Ethernet
(POE). With this feature, the Aruba AP-60/61 can accept electrical power from a
compatible POE-capable device (such as the Aruba 5000 (with Line Card
LC-5000-24FE-2GE-SPOE), Aruba 2400, or Aruba 800) directly over the FE cable.
POE eliminates the need to provide separate power outlets in environments that
are difficult or undesirable to wire for electricity.
The Aruba AP-60/61 also supports “inline” and “midspan” POE devices for
normal operation. Inline power is POE that is integrated into FE ports and provides
POE directly to devices. Non-POE ports can have POE added by means of a
mid-span device that provides POE. The non-POE port is connected to a mid-span
POE port, and this mid-span port is connected to the device that requires POE.
Physical Description
Package Contents
The Aruba AP-60/61 package includes:
z
z
One Aruba AP-60/61 Access Point
Assorted documentation
Inform your supplier if there are any incorrect, missing or damaged parts. If
possible, retain the carton, including the original packing materials. Use them to
repack the product in case there is a need to return it.
Optional Items
The following optional items can also be ordered for the Aruba AP-60/61:
z
z
Detachable antennas (Aruba AP-60 only)
AC power adapter (5 VDC, 3 A) and power cord
Aruba AP-60/61
Installation Guide
27
Product Specifications
Chapter C
z
z
Serial breakout adapter for direct access to the AP console
Mounting kit (modular cradle for walls and suspended ceilings)
Check with your Aruba sales representative for the availability of optional items.
The following specifications apply to the Aruba AP-60 and Aruba AP-61 Access
Points.
Aruba AP-60 Access Point
FIGURE B-1 Part Number: AP-60
28
Aruba AP-60/61
Installation Guide
0510160-03
April 2008
Product Specifications
Chapter C
TABLE B-1 AP-60 802.11 Specifications
Description
802.11a
802.11b
802.11g
Antenna
Dual, diversity supporting Reverse Polarity-SMA (RP-SMA)
detachable antenna interfaces suitable for acceptance of
single-band or tri-band 802.11a/b/g detachable antennas
of various pattern types and gain. For information on
third-party antennas, go to the Interoperability section of
the Products page at:
http://www.arubanetworks.com
Frequency
Band
z
z
5.250 ~ 5.350
Ghz (middle
band)
5.725 ~ 5.825
Ghz (higher
band)
z
z
2.4 ~ 2.483
Ghz (US, Canada & ETSI)
2.4 ~ 2.497
Ghz (Japan)
Complete country
list available at
http://www.aruba
networks.com/pr
oducts/aps/certifi
cation
z
z
z
2.412 ~ 2.462
Ghz (US, Canada)
2.412 ~ 2.472
Ghz (ETSI)
2.412 ~ 2.484
Ghz (Japan)
Complete country
list available at
http://www.arub
anetworks.com/p
roducts/aps/certif
ication
Radio
Technology
Orthogonal
Frequency
Division
Multiplexing
(OFDM)
Direct Sequence
Spread Spectrum
(DSSS)
Orthogonal
Frequency
Division
Multiplexing
(OFDM)
Modulation
Type
BPSK, QPSK,
16-QAM,
64-QAM
CCK, BPSK,
QPSK
CCK, BPSK,
QPSK, 16-QAM,
64-QAM
Transmit
Power
Configurable by
system
administrator/
professional
installer
Configurable by
system
administrator/
professional
installer
Configurable by
system
administrator
Media
Access
Control
CSMA/CA with
ACK
CSMA/CA with
ACK
CSMA/CA with
ACK
Aruba AP-60/61
Installation Guide
29
Product Specifications
Chapter C
TABLE B-1 AP-60 802.11 Specifications
(Continued)
Description
802.11a
802.11b
802.11g
Operating
Channels
z
z
z
z
z
Data Rates
US & Canada: 8
ETSI: 13
Japan: 5
z
z
US & Canada:
11
ETSI: 13
Japan: 13
z
z
US & Canada:
11
ETSI: 13
Japan: 13
Complete
country list
available at
http://www.arub
anetworks.com/p
roducts/aps/certi
fication
Complete country
list available at
http://www.aruba
networks.com/pr
oducts/aps/certifi
cation
Complete country
list available at
http://www.arub
anetworks.com/p
roducts/aps/certif
ication
6, 9, 12, 18, 24,
36, 48, 54 Mbps
per channel
1, 2, 5.5, 11 Mbps
per channel
6, 9, 12, 18, 24,
36, 48, 54 Mbps
per channel
TABLE B-2 AP-60 Characteristics
Description
Maximum
Clients
64
Multi-mode
Radio Band
Selectable via software
Manageability:
z
z
Management of all 802.11 parameters
Network Wide AP Management via:
CLI
WEB GUI
SNMPv3
z
Access Point Profiles, Management by:
Geographical Location
BSSID
Radio Type
Encryption
Support (AP and
Mobility
Controller)
30
Aruba AP-60/61
Installation Guide
40bit / 64bit / 128bit / 152bit WEP, TKIP, AES
0510160-03
April 2008
Product Specifications
Chapter C
TABLE B-2 AP-60 Characteristics
(Continued)
Description
Physical
(HxWxD):
z
z
159 x 99 x 31 mm / 6.26 x 3.90 x 1.22 ina
Weight 198 grams / 7 oz
Interfaces
(Electrical):
z
1 x 10/100 Base-TX auto-sensing Ethernet RJ-45
Interface (Auto-sensing MDI/MDX)
Serial and Power Over Ethernet - 48V DC / 200mA
Power Over Ethernet (802.3af compliant)
1 x 5V DC Power Interface
z
z
Interfaces
(Mechanical):
z
z
Visual Indicators
(LEDs)
Standard Kensington MicroSaver Security Cable
Interface (cable not supplied)
Wall and ceiling mount kit (optional - part number
AP-60-MNT) interface
Ready -- Power
Ethernet link status / Activity
WLAN Activity
Power
z
Optional AC Power Adapter Input—
100-240 AC, 50-60 Hz
z
Access Point Input—
5 VDC, 3 A (AC adapter), or 48 VDC, 200 mA (POE)
Power
Requirements
z
z
z
5 VDC / 2 A supplied externally via optional AC
adapter kit
48 VDC / 200 mA Power Over Ethernet (802.3af
compliant)
Auto-sensing externally supplied AC power or
Power Over Ethernet
Output Power
100 mW maximum (or lower as configured on the
Aruba Mobility Controller to comply with local
regulatory requirements)
Power
Consumption
10 W maximum
Operating
Environment
z
z
0 ºC to 50 ºC (32 ºF to 122 ºF) AP
0 ºC to 40 ºC (32 ºF to 104 ºF) AC Mains Power
Adapter Kit
Storage
Environment
z
z
0 ºC to 70 ºC (32 ºF to 158 ºF) AP
-20 ºC to 70 ºC (-4 ºF to 158 ºF) AC Mains Power
Adapter Kit
Aruba AP-60/61
Installation Guide
31
Product Specifications
Chapter C
TABLE B-2 AP-60 Characteristics
(Continued)
Description
Humidity
z
z
z
Altitude
3,048 m (10,000 feet) maximum
Standards
Compliance
z
z
z
Ethernet IEEE 802.3 / IEEE 802.3u
Power Over Ethernet IEEE 802.3af
Wireless IEEE 802.11a/b/g
Mains
Connections
z
Class II (ungrounded equipment)
Protection
Against Egress
of Water
z
The unit is protected against falling liquids with a
protection class of IPX0 as defined by IEC 60601-1
and IEC 60529.
Mode of
Operation
z
As defined by IEC 60601-1, this unit is considered
“Continuous Operation” equipment.
a.
32
5 to 95%, non-condensing AP
15 to 85% RH AC Mains Power Adapter Kit
5 to 90% RH Storage Humidity AC Mains Power
Adapter Kit
Measurements indicate only the Access Point chassis. Size and weight do not include
other materials (such as detachable antennas, mounting kits, and cables), which may
vary
Aruba AP-60/61
Installation Guide
0510160-03
April 2008
Product Specifications
Chapter C
Aruba AP-61 Access Point
FIGURE B-2 AP-61
Aruba AP-60/61
Installation Guide
33
Product Specifications
Chapter C
TABLE 2-3 AP-61 802.11 Specifications
Description
802.11a
802.11b
802.11g
Antenna
Integral, diversity supporting dual, tri-band 802.11a/b/g
omni-directional high-gain antennas with 90 degrees
rotational movement
Integral antenna gain:
2.4 Ghz / 2.8 dBi
5.150-5.350 Ghz / 3.9 dBi
5.6 Ghz / 4 dBi
Frequency
Band
z
z
z
34
5.150 ~
5.250 Ghz
(lower band)
5.250 ~
5.350 Ghz
(middle band)
5.725 ~
5.825 Ghz
(higher band)
z
z
2.4 ~ 2.483
Ghz (US, Canada & ETSI)
2.4 ~ 2.497
Ghz (Japan)
Complete country
list available at
http://www.arub
anetworks.com/p
roducts/aps/certi
fication
z
z
z
2.412 ~ 2.462
Ghz (US, Canada)
2.412 ~ 2.472
Ghz (ETSI)
2.412 ~ 2.484
Ghz (Japan)
Complete country
list available at
http://www.aruba
networks.com/pro
ducts/aps/certific
ation
Radio
Technology
Orthogonal
Frequency
Division
Multiplexing
(OFDM)
Direct Sequence
Spread Spectrum
(DSSS)
Orthogonal
Frequency
Division
Multiplexing
(OFDM)
Modulation
Type
BPSK, QPSK,
16-QAM,
64-QAM
CCK, BPSK,
QPSK
CCK, BPSK,
QPSK, 16-QAM,
64-QAM
Transmit
Power
Configurable by
system
administrator/
professional
installer
Configurable by
system
administrator/pro
fessional installer
Configurable by
system
administrator
Media Access
Control
CSMA/CA with
ACK
CSMA/CA with
ACK
CSMA/CA with
ACK
Aruba AP-60/61
Installation Guide
0510160-03
April 2008
Product Specifications
Chapter C
TABLE 2-3 AP-61 802.11 Specifications (Continued)
Description
802.11a
802.11b
802.11g
Operating
Channels
z
z
z
z
US, Canada
& ETSI: 12
Japan: 5
Complete
country list
available at
http://www.arub
anetworks.com/
products/aps/cer
tification
Data Rates
6, 9, 12, 18, 24,
36, 48, 54 Mbps
per channel
z
z
US & Canada: 11
ETSI: 13
Japan: 13
z
z
US & Canada:
11
ETSI: 13
Japan: 13
Complete country
list available at
http://www.arub
anetworks.com/p
roducts/aps/certi
fication
Complete country
list available at
http://www.aruba
networks.com/pro
ducts/aps/certific
ation
1, 2, 5.5, 11
Mbps per
channel
6, 9, 12, 18, 24,
36, 48, 54 Mbps
per channel
TABLE B-4 AP-61 Characteristics
Description
Maximum
Clients
64
Multi-mode
Radio Band
Selectable via software
Manageability:
z
z
Management of all 802.11 parameters
Network Wide AP Management via:
CLI
WEB GUI
SNMPv3
z
Access Point Profiles, Management by:
Geographical Location
BSSID
Radio Type
Encryption
Support (AP
and Mobility
Controller)
40bit / 64bit / 128bit / 152bit WEP, TKIP, AES
Aruba AP-60/61
Installation Guide
35
Product Specifications
Chapter C
TABLE B-4 AP-61 Characteristics (Continued)
Description
Physical
(HxWxD):
z
z
z
z
Interfaces
(Electrical):
z
z
z
Interfaces
(Mechanical):
Antenna up, stand closed—216 x 99 x 31 mm /
8.50 x 3.90 x 1.22 ina
Antenna up, stand open—209 x 99 x 74 mm /
8.23 x 3.90 x 2.91 in
Antenna 90o, stand closed— 159 x 99 x 71 mm /
6.26 x 3.90 x 2.80 in
Weight 255 grams / 9 oz
1 x 10/100 Base-TX auto-sensing Ethernet
RJ-45 Interface (Auto-sensing MDI/MDX)
Serial and Power Over Ethernet - 48 VDC/200
mA Power Over Ethernet (802.3af compliant)
1 x 5V DC Power Interface
Standard Kensington MicroSaver Security Cable
Interface (cable not supplied)
Wall and ceiling mount kit (optional - part number
AP-60-MNT) interface
Visual
Indicators
(LEDs)
Ready -- Power
Ethernet link status / Activity
WLAN Activity
Power
z
Optional AC Power Adapter Input—
100-240 AC, 50-60 Hz
z
Access Point Input—
5 VDC, 3 A (AC adapter), or 48 VDC, 200 mA
(POE)
Power
Requirements
z
z
z
36
5 VDC / 2 A supplied externally via optional AC
adapter kit
48 VDC / 200 mA Power Over Ethernet (802.3af
compliant)
Auto-sensing externally supplied AC power or
Power Over Ethernet
Output Power
100 mW maximum (or lower as configured on the
Aruba Mobility Controller to comply with local
regulatory requirements)
Power
Consumption
10W maximum
Aruba AP-60/61
Installation Guide
0510160-03
April 2008
Product Specifications
Chapter C
TABLE B-4 AP-61 Characteristics (Continued)
Description
Operating
Environment
z
z
0 ºC to 50 ºC (32 ºF to 122 ºF) AP
0 ºC to 40 ºC (32 ºF to 104 ºF) AC Mains Power
Adapter Kit
Storage
Environment
z
z
0 ºC to 70 ºC (32 ºF to 158 ºF) AP
-20 ºC to 70 ºC (-4 ºF to 158 ºF) AC Mains
Power Adapter Kit
Humidity
z
z
z
5 to 95%, non-condensing AP
15 to 85% RH AC Mains Power Adapter Kit
5 to 90% RH Storage Humidity AC Mains Power
Adapter Kit
Altitude
3,048 m (10,000 feet) maximum
Standards
Compliance
z
z
z
a.
Ethernet IEEE 802.3 / IEEE 802.3u
Power Over Ethernet IEEE 802.3af
Wireless IEEE 802.11a/b/g
Measurements indicate only the Access Point chassis. Size and weight do not include other materials (such as detachable antennas, mounting kits, and cables),
which may vary
Related Documents
The following items are part of the complete documentation for the Aruba
system:
z
z
z
z
Aruba Quick Start Guide
Aruba AP 60/61 Wireless Access Point Installation Guide (this document)
ArubaOS User Guide
Aruba Mobility Controller installation guide
For the current versions of these manuals, or to obtain the latest product release
notes, visit the support section of the Aruba Web site (see page 38).
Aruba AP-60/61
Installation Guide
37
Product Specifications
Chapter C
Contacting Aruba Networks
Web Site
„
Main Site
http://www.arubanetworks.com
„
Support Site
http://www.arubanetworks.com/support
„
Software Licensing Site
https://licensing.arubanetworks.com
„
Wireless Security Incident
Response Team (WSIRT)
http://www.arubanetworks.com/support
/wsirt
„
Support Email
support@arubanetworks.com
„
WSIRT Email
wsirt@arubanetworks.com
Please email details of any security
problem found in an Aruba product.
Telephone Numbers
„
Aruba Corporate
+1 (408) 227-4500
„
FAX
+1 (408) 227-4550
„
Support
z
United States
800-WI-FI-LAN (800-943-4526)
z
France
+33 (0) 1 70 72 55 59
z
United Kingdom
+44 (0) 20 7127 5989
z
Germany
+49 (0) 69 38 09 77 22 8
z
All other countries
+1 (408) 754-1200
Proper Disposal of Aruba Equipment
This product at end of life is subject to separate collection and
treatment in the EU Member States, Norway, and Switzerland
and therefore is marked with the symbol shown at the left.
Treatment applied at end of life of these products in these
countries shall comply with the applicable national laws
implementing Directive 2002/96EC on Waste of Electrical and
Electronic Equipment (WEEE).
38
Aruba AP-60/61
Installation Guide
0510160-03
April 2008
Product Specifications
Chapter C
The WEEE Directive 2002/96/EC and RoHS (Restriction of
Hazardous Substances) Directive 2002/95/EC sets collection,
recycling and recovery targets for various categories of
electrical products and their waste.
The Restriction on Hazardous Substances Directive (RoHS)
(2002/95/EC), which accompanies the WEEE Directive, bans
the use of heavy metals and brominated flame-retardants in
the manufacture of electrical and electronic equipment.
Specifically, restricted materials under the RoHS Directive are
Lead (including Solder used in PCB's), Cadmium, Mercury,
Hexavalent Chromium, and Bromine.
Aruba declares compliance with the European Union (EU)
WEEE Directive (2002/96/EC). For more information on WEEE,
refer to:
http://www.dti.gov.uk/sustainability/weee/
China RoHS
Aruba products also comply with China environmental declaration requirements
and are labeled with the “EFUP 50” label shown at the left.
᦭Ქ᦭ኂ‛䋼ჿ᣿
Hazardous Materials Declaration
ㇱઙฬ⒓
(Parts)
⬉ 〝᧼
PCA Board
䪙
Lead
(Pb)
ᳮ
Mercury
(Hg)
X
O
᦭Ქ᦭ኂ‛䋼 ᚗర⚛Hazardous Substances)
౐ચ䫀 ᄙ⒈ 㘨 ⧶
䬝
Chromium VI
Polybrominated
Cadmium
Compounds
Biphenyls
(Cd)
6+
(Cr )
(PBB)
O
O
O
ᄙ⒈ ੑ⧶䝮 Polybrominated
Diphenyl Ether
(PBDE)
O
᧍᪾㒘 ઙ
X
O
O
O
O
O
Mechanical
Subassembly
O:⴫␜䆹 ᦭Ქ᦭ኂ‛䋼 ࿷䆹 ㇱઙᚲ᦭ဋ䋼 ᧚ᢱਛ⊛฽㊂ဋ࿷SJ/T11363-2006ᷛ ಎ㾘 ቯ⊛㒢㊂ⷐ᳞એਅ‫ޕ‬
This component does not contain this hazardous substance above the maximum concentration values in homogeneous materials
specified in the SJ/T11363-2006 Industry Standard.
X: ⴫␜䆹 ᦭Ქ᦭ኂ‛䋼 ⥋ዋ࿷䆹 ㇱઙ⊛ᨱ৻ဋ䋼 ᧚ᢱਛ⊛฽㊂⿥಴SJ/T11363-2006ᷛ ಎ㾘 ቯ⊛㒢㊂ⷐ᳞‫ޕ‬
This component does contain this hazardous substance above the maximum concentration values in homogeneous materials specified
in the SJ/T11363-2006 Industry Standard.
ᇍ䫔ଂП᮹ⱘ᠔ଂѻકᴀ㸼ᰒ⼎կᑨ䫒ⱘ⬉ᄤֵᙃѻકৃ㛑ࣙ৿䖭ѯ⠽䋼‫ޕ‬
This table shows where these substances may be found in the supply chain of electronic information products, as of the date of sale of
the enclosed product.
ℸᷛᖫЎ䩜ᇍ᠔⍝ঞѻકⱘ⦃ֱՓ⫼ᳳᷛᖫ
ᶤѯ䳊䚼ӊӮ᳝ϔϾϡৠⱘ⦃ֱՓ⫼ᳳ՟བ⬉∴ऩ‫ܗ‬῵ഫ䌈೼݊ѻકϞ
ℸ⦃ֱՓ⫼ᳳ䰤া䗖⫼Ѣѻકᰃ೼ѻક᠟‫ݠ‬Ё᠔㾘ᅮⱘᴵӊϟᎹ԰
The Environment- Friendly Use Period (EFUP) for all enclosed products and their parts are per the
symbol shown here. The Environment- Friendly Use Period is valid only when the product is operated
under the conditions defined in the product manual. Aruba AP-60/61
Installation Guide
39
Product Specifications
Chapter C
40
Aruba AP-60/61
Installation Guide
0510160-03
April 2008
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising