Wireless 2, 3, and 6-Button Keypad Installation Guide

Wireless 2, 3, and 6-Button Keypad Installation Guide
Accessory
•
4
The optional Low Voltage Keypad Power Supply, model # C4-KPS36-240-M-B
(sold separately), can be used to provide 36V of power to one or multiple
keypads over common low voltage wiring (such as CAT5 Ethernet cable).
Prepare each wire: Strip the wire insulation back 0.30 inch (or 7.64 mm)
from the wire end (as shown).
1
WARNING! To avoid SERIOUS INJURY or DEATH, turn OFF local
electrical power before installing, removing, or replacing keycaps.
Control4 offers standard engraved keycaps and custom engraved keycaps
(both sold separately) to enable you to personalize 3-Button and 6-Button
Keypads.
Ensure that the location and intended use meet the following criteria:
•
•
•
•
•
•
LSZ-3W1-240-W (White)Wireless 2-Button Keypad (802.15.4)
LSZ-3W1-240-B (Black) Wireless 2-Button Keypad (802.15.4)
LSZ-3W1-240-A(Almond) Wireless 2-Button Keypad (802.15.4)
KPZ-3B1-240-W (White)Wireless 3-Button Keypad (802.15.4)
KPZ-3B1-240-B (Black) Wireless 3-Button Keypad (802.15.4)
KPZ-3B1-240-A(Almond) Wireless 3-Button Keypad (802.15.4)
KPZ-6B1-240-W (White)Wireless 6-Button Keypad (802.15.4)
KPZ-6B1-240-B (Black) Wireless 6-Button Keypad (802.15.4)
KPZ-6B1-240-A(Almond) Wireless 6-Button Keypad (802.15.4)
2
220 - 240 VAC +/- 10%, 50 Hz, 1.8 W
Operational Temperature:
0° C to 40° C
Communications:
IEEE 802.15.4, 2.4 GHz, 15-channel,
spread spectrum radio
WARNING! The 2/3/6 Button Keypad must be protected by an
external circuit breaker or a fuse rated at 6A maximum.
WARNING! This unit should only be installed by a “competent
person” or qualified electrician in accordance with the National Wiring
Regulations and other applicable regulations.
WARNING! To reduce the risk of SERIOUS INJURY or DEATH, turn
OFF local electrical power before installing this product, and before
installing, removing, or replacing any wall plate or keycaps.
IMPORTANT! Using this product in a manner other than outlined in
this document voids your warranty. Further, Control4 is NOT liable for
any damage incurred with the misuse of this product. See “Limited 2
Year Warranty.”
IMPORTANT! Do NOT use a power screw driver to install this device.
If you do, you may overtighten the screws and strip them.
IMPORTANT! This is an electronic device with intricate components.
Handle and install with care!
IMPORTANT! Changes or modifications not expressly approved by
Control4 could void the user’s authority to operate the equipment.
Switch off and isolate the mains power at the main
consumer unit or fuse box before starting any installation
or maintenance work.
3
For 3-Button and 6-Button Keypads only:
Control4 offers standard engraved keycaps
and custom engraved keycaps (both sold
separately) to enable you to personalize
3-Button and 6-Button Keypads. If you are
replacing keycaps now (during this
installation), complete the following steps:
Note: Custom engraving is not available for 2-Button Keypads.
Connect the multi-button keypad
terminal block to the wall box
wires.
If you are replacing keycaps in a 3-Button or 6-Button keypad that is already
installed, complete the following steps:
Note: Wall box wires can
differ depending upon how
the box was wired by your
electrician.
Install in accordance with all national and local electrical codes.
The required wall box size is specified by the U.S. NEC (U.S. National
Electrical Code). The internal wall box volume occupied by this multi-button
keypad is 5.0 cubic inches.
The range and performance of the wireless control system is highly
dependent on the following: (1) distance between devices; (2) layout of the
home; (3) walls separating devices; and (4) electrical equipment located near
devices.
If you are planning to use engraved keycaps for 3-Button and 6-Button
Keypads, DO NOT continue until you have read the “Replace Keycaps After
Keypad Installation” section.
If installing a multi-button keypad in a multi-gang installation, DO NOT
continue until you have read the “Multi-Gang Installations” section.
WARNING! As with any electrical device, improper use
or installation can cause SERIOUS INJURY or DEATH. It is important
that you understand the particular wiring configuration of your
installation before proceeding. Note: The wall box wiring shown in
this document is an example. Your wire colours and functions may
differ. If you are not sure which wires are the Live, Neutral, and Earth
wires, have a trained electrician do the installation.
Specifications
Power:
5
WARNING! To reduce the risk of SERIOUS INJURY or
DEATH, turn OFF local electrical power before installing
this product.
This device requires a neutral AC connection.
This multi-button keypad is intended for use in a Control4® system. It installs
in a standard U.S. wall box (one that meets the U.S. National Electrical Code
[NEC] requirements) using typical wiring standards and communicates to the
Control4 system using a wireless connection. The specifications are
described below.
When replacing a traditional 3-way switch, refer to the “Two-Location” sample
wiring configurations provided in the following documents:
Wireless Dimmer Installation and User Guide
Wireless Switch Installation and User Guide
Supported Models and Requirements
Applies to 3-Button and 6-Button Keypads Only
WARNING! This is a Class 1 product
and must be Earthed.
Installation Instructions
Wireless 2, 3, and 6-Button
Keypad Installation Guide
Replace Keycaps After Keypad Installation
1. Turn off local electrical power.
2. Remove the wall plate from the multi-button keypad.
3. Pinch both sides of the keycap retainer at both ends (as illustrated in step
3 of the Installation Instructions)—working gently, first at the top, then the
bottom—to release the retaining clips and remove the retainer. DO NOT
pry the retainer off with a screw driver.
4. Remove the default keycaps from the keycap retainer and replace each
one with the engraved keycap of your choice. Be sure to place the LED at
the top.
5. Carefully snap the retainer back into place, taking care not to damage the
retainer clips.
6. Reattach the wall plate.
Connect the multi-button keypad terminal block to the wall box wires as
indicated in the following table.
Multi-Button Keypad Wires
(2, 3, or 6-Button)
Wires in Wall Box
Blue (Neutral or N)
Blue (Neutral or N)
Brown (Live or L)
Brown (Live or L)
Green with Yellow (Earth or E or
6
7
)
Green with Yellow (Earth or E or
Secure the keypad to the wall box using the screws provided.
Attach the Decora-style screw-on wall plate (included).
WARNING! Do not turn power back on until the
wall plate is completely back in place.
b. Remove the default keycaps from the keycap retainer and replace
damage the retainer clips.
)
Multi-gang installations are configurations in which 2 or more devices are
installed side-by-side in the same wall box. Using a Decora-style screw-on
multi-gang wall plate (not included), align 2 or more multi-button keypads
inside a multi-gang wall box and fasten with screws, then fasten the wall
plate to the keypads with screws.
Operation and Configuration
On initial power up, the unit will flash the Red/Green/Blue (RGB) LEDs,
which can be programmed with different colours for different states or colour
preferences. To set up this multi-button keypad for use with a Control4
system, refer to your system setup documentation.
both ends—working gently, first at the top,
then the bottom—to release the retaining
clips and remove the retainer. DO NOT
pry the retainer off with a screw driver.
c. Carefully snap the retainer back into place, taking care not to
7. Turn on local electrical power.
Multi-Gang Installations
a. Pinch both sides of the keycap retainer at
each one with the engraved keycap of your choice. Be sure to
place the LED at the top.
WARNING! Do not turn power back on until the wall plate is
completely back in place.
Troubleshooting
If one or more Light Emitting Diodes (LEDs) are not lit:
8
9
When installation is complete, turn on the mains power.
Ensure that all LEDs on the front are lit.
•
•
•
Ensure circuit breaker is not turned OFF or tripped.
Check for proper wiring, such as the example in step 5. You may also need to
contact a trained electrician.
For help on the installation or operation of this product, email or call the
Control4 Technical Support Center. Please provide your exact model number.
Contact support@control4.com or see the web site www.control4.com.
Care and Cleaning
•
•
•
Do NOT paint the multi-button keypad or its wall plate.
Do NOT use any chemical cleaners to clean the multi-button keypad.
Clean surface with a soft damp cloth as needed.
Regulatory Compliance
Recycling
This product is designed and tested to meet European, Australian, and New
Zealand standards for EMC compliance and safety.
For information on recycling, please go to www.control4.com/
recycling
Europe—CE Declaration of Conformity
Limited 2 Year Warranty
European Contact Information
Control4 UK Limited
Unit 3, Green Park Business Centre
Sutton-on-the-Forest, York
YO61 IET, United Kingdom
+44 (0) 134781 2300
c4@control4-UK.com
United States Contact Information
Control4 Corporation
11734 S. Election Road, Suite 200
Salt Lake City, UT 84020-6432, USA
Tel (801) 523-3100
Product: 240 Volt 2, 3, or 6-Button Keypad, model numbers vary (see
“Supported Models and Requirements” on page 1).
The undersigned hereby declares, on behalf of Control4 Corporation, that
the above-referenced product, to which this declaration relates, is in
conformity with the provisions of:
•
•
•
•
Council Directive 89/336/EEC (May 3, 1989) on Electromagnetic Compatibility
Council Directive 1999/5/EC (Mar 9, 1999) on Radio & Telecommunication
Terminal Equipment (R&TTE)
Council Directive 2006/95/EC (Dec, 12, 2006) on Low Voltage Equipment
Safety
Council Directive 93/68/EEC (Jul. 22, 1993) Amending Directives 89/336/EEC
and 73/23/EEC
and has been tested to the requirements of, and shown to be in compliance
with, the following requisite standards:
EMC
•
EN301489-1 V1.6.1 (2005-09) — Electromagnetic compatibility and Radio
spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for
radio equipment and services–Part 1 Common technical requirements.
Radio
•
EN300328 V1.6.1 (2004/11) — Electromagnetic compatibility and Radio spectrum Matters (ERM); Wide band transmission systems; Data transmission
equipment operating in the 2.4GHz ISM band and using wide band modulation
techniques; Harmonised EN covering essential requirements under Article 3.2
of the R&TTE Directive.
Safety
•
•
EN60669-1: 1999 — Switches for household and similar fixed electrical installations - Part 1: General requirements.
EN60669-2-1: 2004 — Switches for household and similar fixed electrical
installations - Part 2-1: Particular requirements - Electronic switches.
The Technical Construction File required by these Directives is maintained at
the corporate headquarters of Control4, Salt Lake City, Utah, U.S.A.
Signed,
Paul E. Nagel—Vice President of Engineering, July 3, 2007
-----------------------------------------------------------------------------------------------------
Australian/New Zealand Compliance
•
AS/NZS 3100:2002 General requirements for electrical equipment.
Control4 Corporation ("Control4") warrants that at the time of first-consumer sale, this
product will be free from defects in material and manufacture. Control4 further warrants
that for a period of 2 years (24 months) after initial consumer sale, the product will
function in accordance with its specification, provided that it is installed and maintained
under normal and proper use. This warranty extends only to products purchased directly
from Control4 or an Authorized Control4 Reseller. If the product proves to be defective
in material or workmanship during the warranty period, it may be returned to the place of
purchase and Control4 will, at its sole option, repair or replace the product with a like
product. This warranty provides the consumer purchaser with specific legal rights, which
may vary per state or country. For complete warranty information, including details on
consumer legal rights as well as warranty exclusions, visit www.control4.com/warranty.
Protected under U.S. Patents D519,939 and D518,794 and licensed under
U.S. Patents 5,905,442 and 5,982,103
About this Document
United States Patents Pending. ©2009 Control4. All rights reserved.
Control4, the Control4 logo and Everyday Easy are registered trademarks or
trademarks of Control4 Corporation in the United States and/or other
countries. All other names or brands may be claimed as property by their
respective owners. Pricing and specifications subject to change without
notice. Part Number: 200-00032 Rev C
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising