DPR-17_Software_Upgrade_Instructions

DPR-17_Software_Upgrade_Instructions
DPR-17 Software Upgrade Procedure
The Software on your DPR-17 can be upgraded by loading the software onto an SD card, and then inserting
the SD card in your radio.
Please Note – There are 2 different Software Versions available for the DPR-17. Please ensure you are
updating your radio with the correct Software Version.
Before you perform the software upgrade procedure, you must:
Before you begin the updating procedure, please confirm which software is currently on your radio. This
will determine which software to upgrade your radio to. To do this, please do the following-
How to Check Software version on Radio
1. To view which software version your radio has press and hold the Info button.
2. Rotate the Tuning control until “SW version” is shown on the display.
3. Press and release the Tuning control to view the software version of your radio.
Software Versions:
Software Version DPR17 - VP02F-AU5V replaces the following versions:
VP02E-AU5V, VP02C, VP02B, VP02A
Software Version DPR17- VP01F replaces the following versions:
VP01D, VP01C, VP01B
If you are unsure which Software to upgrade your radio to, please contact Canohm.
Canohm Contact DetailsFreecall: 1800 636 026
E-Mail: sales@canohm.com.au
1
Software upgrade procedure:
1.Extract the file “DPR-17 Software” - Extract the Software and save on your computer – eg. Create
a folder named “DPR-17 Software Upgrade” and save/extract the file into here.
2. Open up the folder where you saved the software upgrade. It should look like the following-
2
3. Open “DPR17+ Software” folder. The following will appear-
4. Open either “DPR17-vp02F-AU5V” or “VP01F” folder, depending on which Software you
need to upgrade to. The following will appear-
3
5. Highlight both “SWTEMPT” and “SWUPGRADE” folder, right click and select “COPY”. Then
paste both folders onto your SD card.
Removable Disk (F).
Click on this
6. Paste both folders onto your SD card. To do this, click on the “Removable Disk” under
Computer. Please see above. This will take you into this section. The right click and press
“PASTE”. Please see below-
Folders pasted in
“Removable Disk”
section
4
7. The Software is now loaded onto your SD card. Please remove SD card from your computer
and insert the SD card into your radio.
8. Turn on your radio, and in any band, press and hold INFO/ADVANCED button, until “Station
List” or “Mono Override” appears and starts flashing (Please Note – if you are in the DAB
band, “Station List” will flash. If you are in the FM band, “Mono Override” will flash).
9. While either “Station List” or “Mono Override” is flashing, release the INFO/ADVANCED
button and rotate the Tuning Knob on the right hand side of the radio, until “SW Upgrade”
appears on the display. Push the Tuning knob in to select “SW Upgrade”.
10. “Press SELECT to confirm upgrade” will appear on the display. Push the tuning knob in
again to confirm the Upgrade.
11. The display will show some data which the Software is upgrading
12. When the process has completed, “Upgrade Success Reconnect Power” will appear on the
display. Please remove either the power supply or the batteries from the radio, reconnect
these and turn the radio back on. The radio will scan and pick up all of the available
stations.
13. Repeat steps 8-12. Please refer below14. Turn on your radio, and in any band, press and hold INFO/ADVANCED button, until “Station
List” or “”Mono Override” appears and starts flashing (Please Note – if you are in the DAB
band, “Station List” will flash. If you are in the FM band, “Mono Override” will flash).
5
15. While either “Station List” or “Mono Override” is flashing, release the INFO/ADVANCED
button and rotate the Tuning Knob on the right hand side of the radio, until “SW Upgrade”
appears on the display. Push the Tuning knob in to select “SW Upgrade”.
16. “Press SELECT to confirm upgrade” will appear on the display. Push the tuning knob in
again to confirm the Upgrade.
17. The display will show some data which the Software is upgrading
18. When the process has completed, “Upgrade Success Reconnect Power” will appear on the
display. Please remove either the power supply or the batteries from the radio, reconnect
these and turn the radio back on. The radio will scan and pick up all of the available
stations.
19. To check the Software has successfully loaded onto your radio, please do the following-
How to Check Software version on Radio
1. To view which software version your radio has press and hold the Info button.
2. Rotate the Tuning control until “SW version” is shown on the display.
3. Press and release the Tuning control to view the software version of your radio.
20. The new version should display either:
DPR17 - VP02F-AU5V or
DPR17 - VP01F
6
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising