please read all directions before starting installation

please read all directions before starting installation
2009-2011 Yamaha R1
Installation Instructions
PARTS LIST
1
1
1
2
1
1
1
1
Ignition Module
CD-ROM
Installation Guide
Velcro
Alcohol swab
CAN cable
CAN termination plug
USB cable
THE IGNITION MUST BE TURNED OFF BEFORE
INSTALLATION!
BEFORE THIS MODULE CAN BE USED THE
POWER COMMANDER MAY NEED TO BE UPDATED.
(SEE INCLUDED INSTRUCTIONS)
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
2191 Mendenhall Drive North Las Vegas, NV 89081 (800) 992-4993 www.powercommander.com
Part #6-87
www.powercommander.com
Yamaha R1 - 1
IGNITION MODULE V
INPUT ACCESSORY GUIDE
ACCESSORY INPUTS
Speed This input has the ability to activate a limiter
based on speed. This is intended to be used
as a pit lane speed limiter. You can use any
OPEN / CLOSED type switch to activate this
feature.
Launch
This input is intended to be used as a launch
control. You can set a target RPM to limit
the bike to when the clutch lever is activated.
Once the clutch lever is released full RPM
can be achieved. This requires a wire be
connected to the grounding side of the clutch
switch and the other end into this input.
Ground
This is a digital ground. You can connect the
BLACK/WHITE crank wire of the SFM to this
location if necessary.
Analog-
Not currently used - updates to follow
Crank-
Connect the WHITE crank wire from the SFM
(if installed) to this input. This is only needed
if you are going to use the Rev Xtend feature.
USB CONNECTION
CRANK
ANALOG
(not used)
GROUND
EXPANSION PORTS 1 & 2
LAUNCH CONTROL
Connect to PCV and SFM
SPEED LIMITER
SPEED LIMITER
Wire connections:
To input wires into the IM first remove the rubber
plug on the backside of the unit and loosen the
screw for the corresponding input. Using a 22-24
gauge wire strip about 10mm from its end. Push the
wire into the hole of the IM until is stops and then
tighten the screw. Make sure to reinstall the rubber
plug.
NOTE: If you tin the wires with solder it will make
inserting them easier.
Part #6-87
www.powercommander.com
Yamaha R1 - 2
FIG.A
IM
ha
rn
e
ss
1
Remove the seat. Prop the fuel tank up.
2
Lay the Ignition Module near the battery and route the harness down the right
side of the bike. Route the harness underneath the battery bracket (Fig. A).
3
Attach the ground wire of the Ignition Module to the negative side of the
battery.
4
Plug the CAN cable into 1 of the ports of the Ignition Module and the other
end into 1 of the ports of the PCV.
5
Plug the CAN termination plug (plastic) into any one of the remaining open
ports of the Ignition Module or PCV.
6
Unplug the 12 pin connector next to the crank case breather (Fig. B).
7
Unplug the BLACK 2 pin connector from the crank pickup coil (Fig. B)
8
Plug the connectors from the Ignition Module in-line of the stock wiring
harness (Fig. C).
9
Reinstall fuel tank and seat.
FIG.B
Unplug
Unplug
FIG.C
Part #6-87
www.powercommander.com
Yamaha R1 - 3
FIG.D
Connecting to the clutch wire for launch control:
Part #6-87
www.powercommander.com
Connect a wire to INPUT #5 of the Ignition Module and the other end to the
BLU/YEL wire of the stock wiring harness at the clutch switch.
Yamaha R1 - 4
PCV
Ignition Module
From SFM
Speed limiter use
inputs 6 & 7
Lauch control input 5
Connecting the Ignition Module to the PCV:
•
The WHITE and the BLK/WHT wires from the Ignition Module are used ONLY if you want to use the Rev Xtend feature of the PCV. If you do NOT
plan on using this feature then just tape the wires out of the way.
•
If you do plan on using the Rev Xtend feature then connect the WHITE wire from the Ignition Module to the #1 input position of the PCV. Connect the
BLK/WHT wire to the #4 input position of the PCV. The BLK/WHT wire can also be connected to the #6 input position of the PCV if necessary.
•
If you are also using the SFM (Secondary Fuel Module) then you will need to connect the WHITE and BLK/WHT wires from the SFM into the Ignition
Module. Connect the WHITE wire from the SFM to the #1 input position of the Ignition Module. Connect the BLK/WHT wire to the #4 input position
of the Ignition Module. The BLK/WHT wire can also be connected to the #6 input position of the Ignition Module if necessary.
Adding the Ignition Module to the PCV network:
•
First download the latest version of Control Center software which is 1.0.6.1.
•
To use the Ignition Module you may need to update your firmware in the PCV (and SFM if being used). Make sure the units are updated to firmware
version 0.1.8.3 or newer. Go to VIEW - Device Information to see the current version. If you need to update the firmware go to Power Commander
Tools - Update firmware. The latest version of firmware and software can be found on the downloads page of www.powercommander.com or on the
included CD.
•
Connect a USB cable to the PCV and another USB cable to the Ignition Module. The software will ask you to add the Ignition Module to the network.
Click OK. Go to Power Commander Tools - Manage Network and click on Sync Devices Utility. Follow the on screen instructions.
Part #6-87
www.powercommander.com
Yamaha R1 - 5
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising