Quick Start Guide

Quick Start Guide
LT-24C340_341_QSG_Final_RC140530.pdf 1 17/6/14 10:18 am
4 Connecting the Aerial and the Mains Socket
1. Connect one end of the RF coaxial cable to the aerial socket on
the wall and the other end of the cable to the RF (75Ω) socket at
the rear right side of your TV.
Quick Start Guide
2. Connect the mains cable to the mains socket after you have
completed all the connections.
3. At this stage, the TV switches to standby mode. The red LED
indicator will illuminate on the front panel of the TV.
24” LED TV WITH
DVD PLAYER
OR
4. In standby mode, press the button on the right side panel of
the TV or on the remote control to turn the TV on. The red LED
indicator will turn blue.
RF Coxial Cable
(not included)
2 To mains socket
Do not connect the TV to the mains supply until you have
completed all the connections.
USB
HDMI2
COMMON INTERFACE (CI)
HDMI1(ARC)
HEADPHONE
5V
PC IN
1
RF
PC AUDIO
500mA
LT-24C340 / LT-24C341
5 Turning the TV On for the First Time
Thank you for purchasing your new JVC TV.
The first time you turn the TV on, it will go straight into the First Time Installation menu.
Your new TV incorporates the latest technology to enhance your viewing
experience. We would suggest that you allow about 20 mins for initial
setup.
First Time Installation
Please ensure aerial is plugged in!
Please follow this guide for a successful first time installation.
1. Press the OK button to start First
Time Installation menu.
Then press OK button.
Country
UK
Ireland
Norway
Sweden
Finland
Denmark
France
Spain
Portugal
4. Press the
buttons to
select the country where you will
operate the TV. Press the OK
button to confirm.
OK
The latest eco-friendly power-saving technology will switch off the TV if
device is left on and idle for 4 hours. Please refer to “Auto Standby” under
the “Time Settings” section of the instruction manual for more detail.
Please select an OSD Language
English
ýesky
Svenska
Slovak
Dansk
Norsk
Remove all packaging from the unit. Retain the packaging.
If you dispose of it please do so according to any local regulations.
TV
Screw A x 1
TV Stand Support
Screw B x 4
TV Base
Instruction Manual
Remote Control /
AAA Batteries x 2
Quick Start Guide
1. Press and lift the back
cover to open the battery
compartment of the
remote control.
2. Insert two AAA size
batteries. Close the
battery compartment
cover.
Rear Spacers x 4
3 Installing the Base Stand
1. Lay the TV down on a flat surface with the back side facing up, and ideally at the edge of a table so that the base of the TV slightly overhangs on it. Please
make sure a soft cushioned material (such as a pillow or thick piece of foam) is placed beneath the screen.
2. To install the TV stand, first attach the stand support to the TV by using screw A. Align with the screw hole then use screws to fix the stand support to the
TV.
Mode Select
Home Mode
Shop Mode
Screw A x 1
Base Stand
Front
Screw B x 4
DTV
Radio
Data
36%
: 3 Channel(s)
: 0 Channel(s)
: 0 Channel(s)
UHF CH
(DTV)
Press [MENU] to skip.
During tuning your TV may have received signals
from more than one transmitter. If this has occurred
the Target Region Descriptor screen will be displayed.
This will enable you to select the correct regional
transmission for the local news service that you
require.
Press the
buttons to adjust each option's setting
and then press the OK button to confirm.
This will be shown as GBR for the UK.
This will show the regional country
(e.g. England, Wales, Scotland, NI).
This will allow you to set the region
for your local news service on BBC
and ITV (e.g. London, Beds and
Cambs etc).
Target Region Setting
Country Code
GBR
Primary Region
England
Secondary Region
London
Tertiary Region
You may receive signals from more than
one transmitter within the Secondary
Region, (e.g Beds and Cambs may have
Luton or Sandy Heath).
screw in
screw in
3. Press the
buttons to select
your desired mode and then press
the OK button. Press the button
to select Yes to confirm or the
button to select No to cancel
and return to the Mode Select
menu.
6 Target Region Setting
3. To install the base stand, align the screw holes, then secure with a screw driver (not included) using the 4 screw B provided.
TV Front
5. DTV Channel tuning will
commence. This operation may
take up to 3 minutes. The display
will show the progress of the
tuning and the number of
channels found.
Channel Tuning
OK
Install the batteries correctly by following the polarity (+ and -) indications
in the battery compartment.
If you select Ireland as the country where you will operate the TV, a
pop-up screen will be display. You will need a 4-digit activation code for
Irish tuning. This code can be found in-store, on the back of your receipt
(if bought in Ireland), or call the customer service team / KNOWHOW.
OK
2 Operating Your Remote Control
1 Unpacking
Suomi
2. Press the
buttons to
select your desired language to be
displayed on the menu. The
default on-screen menu language
is set as English. Press the OK
button to confirm.
Well done,
your new TV is now ready to use. You will find that there are many exciting features available. To get to know all these features, please
take some time to read the instruction manual provided with your TV.
If after reading the instruction manual you have additional questions related to the use of your TV please call:
• UK Call Centre on 0344 561 1234.
• Ireland Call Center on 1 890 818 575.
(QSG-LT-24C340_341-140530V2)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising