Instruction Manual

Instruction Manual
Instruction Manual
www.winegard.com/carryout
For receivers and programming, call 1-866-609-9374
SD
SD/HD
SD/HD
For up-to-date information on receiver compatibility and programming,
visit www.winegard.com/receivers
For help, email help@winegard.com or call 1-800-788-4417
Do not return antenna to place of purchase
Power Inserter
See page 2 for setup instructions
For Sales Information Please Contact RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.; Wilmington, NC 28411 - (800) 507-0482 / (910) 686-4281
2452360
For Sales Information Please Contact RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.; Wilmington, NC 28411 - (800) 507-0482 / (910) 686-4281
Specifications
Compatible with DIRECTV®,
DISH®, & Bell TV™ programming
Supports up to two receivers
For stationary use only
Includes 25’ coaxial cable,
3’ coaxial cable,
and power inserter
Unit weight: 10 lbs
Unit height (no feet): 13.5"
NOTE
DIRECTV Sat. 119°
Dome
Base
Eyelet
Handle
Diameter: 14.3"
Elevation range: 18–65°
Azimuth: 0–416°
UV-protected plastic dome
Operating temperature specifications: -25° to 70° C
(-13° to 158°F)
Compatible Receivers
Receiver models change frequently. For an up-to-date list of
compatible receivers, visit www.winegard.com/receivers.
DISH Sat. 110°
DIRECTV Receiver Compatibility
The Carryout G2+ antenna is not compatible with DIRECTV
SWM-only receivers (e.g. H25 or HR34). If you have a SWMonly technology receiver, Winegard Model SWM-840 kit is
available. This SWM kit will allow for proper SWM technology
operation with Winegard mobile satellite TV antennas.
DISH Receiver Compatibility
Operation may require an HD receiver. The antenna is not
compatible with DISH Hopper™ or Joey™ receivers. Dual tuner
receivers will require two coax connections from the antenna. In
order to simultaneously watch or record two different programs,
each program must be broadcast from the same satellite.
DISH Sat. 119°
Compatible Satellites
DIRECTV:101° or 119° (will not receive HD on 110° or any KAband HD on 99° and 103°)
DISH (Western Arc): 110°, 119°, 129°
Bell TV: 91° or 82°
Refer to maps* to determine coverage in areas of the U.S.
Good
Signal Strength
DIRECTV Sat. 101°
1
Best
DISH Sat. 129°
*Source: www.satbeams.com. Coverage maps are approximate and do not guarantee coverage.
Carryout G2+ Antenna
3. Choosing a Location
Warnings
! Do not place the unit in water greater than one inch deep,
or water may damage the electronics.
1. Choose a location with a clear, unobstructed view of the
southern sky. Avoid obstructions such as trees, hills, vehicles,
or buildings—these can block the signal from the satellite.
! Do not install or operate the antenna in winds of 35 mph
or greater. The antenna will roll in winds ≥35 mph.
NOTE
Satellite signal will not pass through solid objects. For
this reason, it is vital to select a location with a clear,
unobstructed view of the southern sky.
! Care should be taken when transporting and setting up the
antenna. Do not toss or drop the antenna.
! Do not paint the antenna. Painting the antenna may cause
signal degradation and will void your warranty.
2. Make sure the antenna is not placed in the path of people or
vehicles; otherwise, the antenna may be knocked off of the
signal if run into, or cables may be disconnected from the unit.
3. Select a location that will enable the Carryout G2+ antenna to
sit within three degrees of level. The antenna may take longer
to lock onto signal if the antenna is not level.
1. Switch Settings
The Carryout G2+ antenna switch settings are located on
the Winegard Power Inserter and are preset for DIRECTV
programming.
4. Wiring the Antenna
Power Inserter switches
TIP
Run the coaxial cable directly from the satellite receiver
to the Carryout G2+ antenna when searching for signal.
1. Ensure the power button on the Winegard Power
Inserter is in the OFF position (not pressed in).
To set the antenna for any other programming provider,
locate the switches on the Power Inserter and set according
to the diagram below:
Switch Settings—Up (
DIRECTV
1
2
3
4
5
6
7
8
) or Down (
The Carryout G2+ is preset
for DIRECTV programming.
The switch settings must be
changed to receive DISH or
Bell TV programming.
DISH
1
2
3
4
5
Bell TV
6
7
8
1
2
3
4
5
6
7
8
2. Installing the Handle
1. Locate the two screws for the handle in the base. Remove
the screws from the base with a Phillips screwdriver.
NOTE
)
2. Connect the included 25’ coaxial
cable between the primary port
of the Carryout G2+ and the
ANTENNA port on the Power
Inserter. Tighten coax connections
until finger tight, and tighten a
quarter turn more with a wrench.
Do not overtighten.
Coax to
Antenna
NOTE
A 25’ coaxial cable is
included with the antenna.
To ensure proper operation, use only
the included coaxial cable. Failure to
use the included coax cable or use of
the interior/exterior pre-wiring could
hinder proper operation.
3. Connect the included 3’ coaxial
cable between the “SAT IN” port
of your satellite receiver and the
RECEIVER port of the Winegard
Power Inserter. Tighten coax
connections until finger tight, and
tighten a quarter turn more with a
wrench. Do not overtighten.
Power
Inserter
Receiver
4. Plug power adapter into
110/120VAC outlet and connect
to power port on Power Inserter
(located next to RECEIVER coax
port).
The two holes for the handle are located between
the cable connections and eyelet.
2. Locate the handle in the box. With “WINEGARD” on the
handle facing upwards, align the two holes in the handle
with the two holes in the base.
3. Thread two screws through the two aligned holes in the
bottom of the handle.
5. Once system is fully connected,
press the power button on the Power Inserter.
6. Give the Carryout G2+ antenna approximately 3-5 minutes
to complete the search sequence. Once the Carryout G2+
antenna has gone completely quiet, proceed to configure
receiver for desired operation. For DIRECTV, see page 3.
For DISH, see page 4.
4. Tighten the two screws using a Phillips screwdriver.
Do not overtighten.
Carryout G2+ Antenna
For Sales Information Please Contact RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.; Wilmington, NC 28411 - (800) 507-0482 / (910) 686-4281
2
For Sales Information Please Contact RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.; Wilmington, NC 28411 - (800) 507-0482 / (910) 686-4281
5. Receiver Setup
5. Select 3-LNB (18”x 20”) or 3 Satellites. If given the option of
SWM or Multiswitch, select Multiswitch.
Connect the receiver to a power source, and complete
receiver setup. Receiver setup for the primary receiver
follows; if your receiver differs from the options shown, you
may need to consult your receiver manual. The wording and
display used in your receiver may differ slightly.
Check out online receiver setup guides for your antenna at
www.winegard.com/receivers/setupguide.php.
For more information on receiver compatibility and
programming, visit www.winegard.com/receivers.
DIRECTV Receiver Setup
1. Press Menu on your remote.
Select Parental, Fav’s & Setup.
6. Power on the antenna, and allow the antenna a few minutes
to acquire signal. Once the antenna has finished acquiring
signal, the antenna will be silent.
7. After the antenna has acquired signal, press Continue; the
receiver will automatically verify the setup.
2. Select System Setup.
8. Errors may be displayed on the screen. It is normal to see one
or two boxes with an X instead of a . Select Continue.
3. In your receiver menu, you will need to identify the Satellite
menu. Once there, find the option for Satellite Setup.
9. Select Continue again. The program guide will download.
10. When the status bar reaches 100%, press Continue.
11. The receiver will run Data Feed and Guide Feed Tests for a
few moments.
12. When prompted to set up the remote, select Setup Remote
Later to do this at a later time.
13. Select Watch DIRECTV. Receiver setup is now complete.
4. You may be required to press the DASH (-) before proceeding
(underneath #7 on the remote).
3
Receiver setup instructions are accurate at time of printing and may change without notice.
Carryout G2+ Antenna
DISH Receiver Setup
5. Select Check Switch.
If using two DISH receivers with the Carryout G2+
antenna, both receivers must be configured off of the primary
port by following the steps below.
1. Disconnect coax cable from the Satellite In port on the back
of the receiver.
Satellite In
port
Back of 211z receiver shown
2. Press Menu on your remote. Select option 6, System Setup.
6. Select Test. It will go through a number of steps, then return
to the screen shown here with previous information cleared.
If at any point it asks you to save, select Save or Yes.
3. Select option 1, Installation.
7. Reconnect coax cable to “Sat In” port on back of receiver.
Power on the antenna. Allow the antenna 3–4 minutes to
acquire satellites.
8. Check that there are no check marks by SuperDISH or
Alternate. If setting up a DISH 311, 301, or 500 series
receiver, in some cases you may need to check the boxes
next to SuperDish and Alternate before running the Check
Switch test.
9. Next, select Test again to install the SW64 switch. This SW64
switch is a DISH receiver setting, not a physical part.
4. Select option 1, Point Dish.
10. When you see the SW64 as the installed switch, the antenna is
ready for use.
Carryout G2+ Antenna
For Sales Information Please Contact RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.; Wilmington, NC 28411 - (800) 507-0482 / (910) 686-4281
4
Troubleshooting
Issue
Possible Cause
Solution
Vin indicator unlit on power
inserter
• No DC power into power inserter
• Ensure power adapter is plugged into outlet and that outlet is
providing AC power
• Ensure power adapter is connected to power inserter
Receiver indicator unlit on power
inserter
• No communication between receiver
and power inserter
• Ensure 3’ coaxial cable between receiver and power inserter’s
RECEIVER port is properly connected
• For DIRECTV users, ensure receiver is compatible and
configured correctly. See page 3 for configuration instructions
• If cable is connected and receiver is properly configured, try
different piece of RG6 coaxial cable
Receiver indicator faintly lit or
flickering on power inserter
• Intermittent communication between
receiver and power inserter
• Replace 3’ coaxial cable piece with a different piece RG6
coaxial cable
Antenna indicator unlit on power
inserter
• No communication between power
inserter and Carryout G2+ antenna
• Ensure included 25’ coaxial cable is being used and is properly
connected between power inserter’s ANTENNA port and
Carryout G2+ PRIMARY port
• Ensure power button on power inserter pushed in ON position
• Replace 25’ coaxial cable with different RG6 coaxial cable
Antenna indicator faintly lit or
flickering on power inserter
• Intermittent communication between
power inserter and Carryout G2+
• Ensure included 25’ cable is being used and is properly
connected between power inserter ANTENNA port and
Carryout G2+ PRIMARY port
• Replace 25’ coaxial cable with a different RG6 coaxial cable
The antenna continuously searches
and eventually stops without ever
acquiring any satellites.
• Possible obstructions are blocking
signal from the satellite
• Check to see if the southern sky is clear. Trees, buildings, large
signs, or an overpass can block the signal
• Rain, snow, or excessive dew on the dome can interrupt the
signal. Brush any snow or dew off of the dome. If heavy rain or
snowfall is blocking the signal, it may be necessary to wait until
the weather clears.
The antenna appears to lock onto
signal, but my receiver does not
show a picture or signal reading
• Receiver improperly configured for
the Carryout G2+ antenna
• Verify the switch settings are set correctly for the desired
provider. See switch settings on page 2
• Reconfigure the receiver according to steps on page 3 or 4
I have switched satellite service
providers, and the antenna is no
longer working properly
• Switches are not set for the correct
provider
• Set the switches to the correct programming provider. See
switch settings on page 2
If a problem persists, contact Winegard Technical Services at help@winegard.com or 1-800-788-4417.
FCC Guidelines
Changes or modifications not expressly approved
by Winegard could void your authority to operate
the equipment.
5
NOTE
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications.
For Sales Information Please Contact RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.; Wilmington, NC 28411 - (800) 507-0482 / (910) 686-4281
Carryout G2+ Antenna
Using Outside Receptacle
Optional Accessories
If your outside TV receptacle is wired for satellite, you’ll need
to locate where that receptacle leads and connect that directly
to your satellite receiver.
MT-4000 Ladder Mount
If the outside TV receptacle is wired for cable, the wiring will
have to be modified for use with satellite. The coaxial cable
cannot run through any other devices or switches before the
satellite receiver.
Typically, if wired for cable, the wiring will either run through
a Winegard power supply or video switch. The easiest way
to fix this is to disconnect the cable from that device, use a
barrel connector, and connect a new cable that runs directly
to the receiver, bypassing the power supply or video switch.
Permanent or temporary mount for
RV with quick disconnect. Creates
all the benefits of an ultra low profile
roof mounted antenna plus quick and
easy portability.
RK-2000 Roof Mount Kit
Permanently mount the Carryout G2+
antenna to your vehicle roof. No need
to buy another antenna to replace your
portable.
TR-1518 Tripod Mount
The tripod mount has adjustable
height and leveling settings of
14.5”– 22” and quickly disassembles
for compact storage.
MT-SM30 Window Mount
Transporting & Maintenance
Temporary mount with maximum
flexibility. Easy one time assembly.
Includes 2 brackets for temporary side
mount opt.
Before transporting the antenna, disconnect all coaxial
cabling from antenna and power inserter. Unplug power
adapter from outlet.
The Carryout G2+ antenna is designed to be maintenance
free. However, it is a good idea to periodically clean the dome
with a soft cloth, water, and dish soap.
For more information or to purchase accessories
contact your local RV dealer or winegard.com
Carryout G2+ Antenna
For Sales Information Please Contact RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.; Wilmington, NC 28411 - (800) 507-0482 / (910) 686-4281
6
WINEGARD MOBILE PRODUCTS LIMITED WARRANTY
(2 YEARS PARTS; 1 YEAR LABOR)
Winegard Company warrants this product against defects in materials or workmanship for a period of two (2) years from the
date of original purchase. During year one (1) of such warranty, Winegard Company will also pay authorized labor costs to
an authorized Winegard dealer to repair or replace defective products. No warranty claim will be honored unless at the time
the claim is made, Customer presents proof of purchase to an authorized Winegard dealer (to locate the nearest authorized
Winegard dealer, contact Winegard Company, 3000 Kirkwood Street, Burlington, Iowa 52601, Telephone 800-288-8094 or visit
www.winegard.com). Customer must provide proof of purchase with a dated sales receipt for the Winegard product to verify
the product is under warranty. If the date of purchase cannot be verified, the warranty period shall be considered to begin thirty
(30) days after the date of manufacture.
If a defect in material or workmanship is discovered, Customer may take the product to an authorized Winegard dealer for
service. Customer must provide proof of purchase to verify the product is under warranty. If the product is brought to an
authorized Winegard dealer for service prior to expiration of year one (1) of the warranty period and a defect in material or
workmanship is verified by Winegard Technical Services, Winegard Company will cover the Winegard dealer’s labor charges for
warranty service. The Winegard dealer must contact Winegard Technical Services in advance for pre-approval of the service.
Approval of the service is at the sole discretion of Winegard Company.
Alternatively, Customer may ship the product prepaid to Winegard Technical Services (located at 2736 Mt. Pleasant Street,
Burlington, Iowa 52601, Telephone 800-788-4417). Customer must return the product along with a brief description of the
problem and provide Winegard Technical Services with Customer’s name, address, and phone number. Customer must
also provide proof of purchase to verify the product is under warranty. If the product is returned before the expiration of the
warranty period, Winegard Company will (at its option) either repair or replace the product.
This Limited Warranty does not apply if the product has been damaged, deteriorates, malfunctions or fails from: improper
installation, misuse, abuse, neglect, accident, tampering, modification of the product as originally manufactured by Winegard in
any manner whatsoever, removing or defacing any serial number, usage not in accordance with product instructions or acts of
nature such as damage caused by wind, lightning, ice or corrosive environments such as salt spray and acid rain. This Limited
Warranty also does not apply if the product becomes unable to perform its' intended function in any way as a result of the
television signal provider making any changes in technology or service.
RETURN AUTHORIZATION POLICY
A Return Material Authorization (RMA) is required prior to returning any product to Winegard Company or Winegard Warranty
Services under this warranty policy. Please call our Technical Services Department at 800-788-4417 or send an email to
warranty@winegard.com to obtain the RMA number. Please furnish the date of purchase when requesting an RMA number.
Enclose the product in a prepaid package and write the RMA number in large, clear letters on the outside of the package. To
avoid confusion or misunderstanding, a shipment(s) without an RMA number(s) or an unauthorized return(s) will be refused and
returned to Customer freight collect.
WINEGARD COMPANY DOES NOT ASSUME ANY LIABILITIES FOR ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, MADE
BY ANY OTHER PERSON.
ALL OTHER WARRANTIES WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING WARRANTIES OF FITNESS FOR A
PARTICULAR PURPOSE AND MERCHANTABILITY ARE LIMITED TO THE TWO YEAR PERIOD OF THIS WARRANTY.
In states that do not allow limitations on implied warranties, or the exclusion of limitation of incidental or consequential
damages, the above limitations or exclusions do not apply.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion of limitation of incidental or
consequential damages, so the above limitations or exclusions may not apply to you.
This warranty gives Customer specific legal rights. Customer may also have other rights that may vary from state to state.
SATELLITE RECEIVER WARRANTY
See manufacturer’s limited warranty policy.
WS-MOBWARREV3
Winegard and Carryout are registered trademarks of Winegard Company.
DISH is a registered trademark of DISH Network L.L.C. DIRECTV is a registered trademark of DIRECTV, LLC. Bell TV is a registered trademark of Bell Canada, Inc.
Disclaimer: Although every effort has been made to ensure that the information in this manual is correct and complete, no company shall be held liable for any
errors or omissions in this manual. Information provided in this manual was accurate at time of printing. If the antenna does not function as expected, please
contact Winegard Company at help@winegard.com or 1-800-788-4417, or visit our website at www.winegard.com.
Winegard Company • 3000 Kirkwood Street • Burlington, IA 52601 • 1-800-288-8094 • Fax 319-754-0787 • www.winegard.com
Printed in U.S.A. ©2015 Winegard Company Rev0 11/15 2452360
Rev0 11/15 2452360
For Sales Information Please Contact RoadTrucker Inc (www.RoadTrucker.com)
8312 Sidbury Rd.; Wilmington, NC 28411 - (800) 507-0482 / (910) 686-4281
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising