FLM-325-I4-A Contact Monitors
Fire Alarm Systems | FLM-325-I4-A Contact Monitors
FLM-325-I4-A Contact Monitors
www.boschsecurity.com
The FLM-325-I4-A and FLM-325-I4-AI modules are used
to connect standard Normally Open or
Normally Closed dry contact types of fire alarm
devices such as pull stations or water flow devices.
The modules are mounted to a cover plate for a
4‑inch square or double‑gang electrical back box. A
bi‑colored LED provides the module status.
u
Monitors Normally Open (NO) or Normally
Closed (NC) contacts
u
Monitored Normally Closed (NC) contacts can be
configured with or without EOL resistor
u
Module address programming with the D5070
Analog Device Programmer
u
Bi‑colored LED provides module status
u
Digital data communications and power over a
two‑wire circuit
Certifications and approvals
Region
Certification
USA
UL
UOXX: Control Unit Accessories, System
(ANSI/UL 864)
CSFM
see our website
FDNYCoA
#6101
Functions
Address Range
Contact Monitor modules must be programmed with a
unique address. All devices connected to module
appear only as one single address at the fire panel.
The modules are compatible with 254 addresses.
Status Conditions
The module supervises the wiring to the contact with
an EOL resistor. If a fault condition occurs, the module
sends a trouble signal to the fire panel.
If a status change occurs, the module sends an
interrupt signal to the fire panel indicating that an
alarm has occurred.
Installation/configuration notes
Compatibility Information
The following products are compatible with the
modules:
Category
Product ID
Product Description
Fire Panels
FPA‑1000
series
Analog Addressable Fire Panels
Programmer
D5070
Analog Device Programmer
Data Circuit Length
Data (or polling) circuit length is the distance over the
circuit wire from the connection at the fire panel to
the most distant device and back to the fire panel.
Data circuit length must include the distance to any
2 | FLM-325-I4-A Contact Monitors
device connected to the circuit in a T‑tap. The screw
terminals can accept 14 AWG (ISO 2.5 mm2) wire;
thinner wire can be used, but this reduces the
allowable length of the circuit.
Initiating Device Circuit Connections
The initiating device circuit can use any number of UL
listed Normally Open (NO) contact closure devices.
Device circuit wiring must not exceed 50 Ω. Install
contact closure devices according to the
manufacturer’s installation instructions. All wiring
must be supervised and power-limited.
Notice
Do not mix fire alarm initiating and supervisory
devices on the same module.
Parts included
Quant.
Component
1
FLM‑325‑I4-A Family Contact Module
1
EOL resistor, 10 kΩ
1
Wall plate
1
Hardware pack
1
Literature pack
Technical specifications
Power Requirements
Input Voltage
25.3 VDC to 39 VDC
Current Consumption
• Nominal:
0.63 mA
• Maximum:
6.3 mA
Resistance
• End of Line Device
10 kΩ, 0.25 W per resistor
• Initiating Device
Circuit
Less than 50 Ω
Mechanical Properties
Dimensions (H x W x D):
4.7 in. x 4.2 in. x 1.4 in.
(11.9 cm x 10.7 cm x 3.6 cm)
Weight
20 oz (567 g)
Color
Ivory
Material
ABS Blend
Response Time
2 sec
Environmental Considerations
Operating Temperature
+32°F to +120°F (0°C to +49°C)
Relative Humidity
Up to 90 %, non‑condensing
Ordering information
FLM-325-I4-A Contact Monitor 4-inch Class A
Can be wired for Class A or Class B circuits; mounted
to a cover plate for a 4‑inch square or double gang
electrical back box; bi‑colored LED provides module
status; compatible with 254 addresses
Order number FLM-325-I4-A
FLM-325-I4-AI Contact Monitor 4-inch Class A with Isolator
Can be wired for Class A or Class B circuits; has
built‑in short circuit isolator circuitry; mounted to a
cover plate for a 4‑inch square or double gang
electrical back box; bi‑colored LED provides module
status; compatible with 254 addresses
Order number FLM-325-I4-AI
3 | FLM-325-I4-A Contact Monitors
Represented by:
Americas:
Bosch Security Systems, Inc.
130 Perinton Parkway
Fairport, New York, 14450, USA
Phone: +1 800 289 0096
Fax: +1 585 223 9180
security.sales@us.bosch.com
www.boschsecurity.us
Europe, Middle East, Africa:
Bosch Security Systems B.V.
P.O. Box 80002
5617 BA Eindhoven, The Netherlands
Phone: + 31 40 2577 284
Fax: +31 40 2577 330
emea.securitysystems@bosch.com
www.boschsecurity.com
© Bosch Security Systems 2014 | Data subject to change without notice
2699165195 | en, V9, 31. Jul 2014
Asia-Pacific:
Robert Bosch (SEA) Pte Ltd, Security
Systems
11 Bishan Street 21
Singapore 573943
Phone: +65 6571 2808
Fax: +65 6571 2699
apr.securitysystems@bosch.com
www.boschsecurity.asia
China:
America Latina:
Bosch (Shanghai) Security Systems Ltd. Robert Bosch Ltda Security Systems Division
201 Building, No. 333 Fuquan Road
Via Anhanguera, Km 98
North IBP
CEP 13065-900
Changning District, Shanghai
Campinas, Sao Paulo, Brazil
200335 China
Phone: +55 19 2103 2860
Phone +86 21 22181111
Fax: +55 19 2103 2862
Fax: +86 21 22182398
latam.boschsecurity@bosch.com
www.boschsecurity.com.cn
www.boschsecurity.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising