Roadie ChristieTWIST™ Warping Module Installation Instruction Sheet

Roadie ChristieTWIST™ Warping Module Installation Instruction Sheet
Roadie ChristieTWIST™
Warping Module Installation
Instruction Sheet
SAFETY AND WARNING GUIDELINES
HIGH VOLTAGES MAY BE EXPOSED! Always power down and
disconnect power sources prior to servicing. Once the projector is powered down,
allow the cooling fans to automatically turn OFF before disconnecting from AC and
opening the projector.
QUALIFIED SERVICE TECHNICIANS REQUIRED! All module
replacement procedures must be performed by Christie accredited service technicians.
NON-INSULATED DANGEROUS VOLTAGES MAY BE EXPOSED! Always
disconnect from AC prior to disassembly.
OBSERVE ALL ELECTROSTATIC PRECAUTIONS! Use a grounded wrist
strap when handling electronic assemblies.
Never operate the projector (or the fans) without all the covers
installed.
INTRODUCTION
These instructions explain how to upgrade the following Christie products to include the
ChristieTWIST™ Warping Module:
Warping Module
P/N 113-109101-01
Roadie 25K
Roadie 25K LE
Roadie HD+30K
Roadie HD+30K
Roadie ChristieTWIST™ Warping Module Installation Instruction Sheet
020-100615-02 Rev. 1 (11-2010)
1 of 8
With the Module and related software both installed, you can use your PC to shape projected images as
desired, defining new corner points and/or applying custom curved (i.e., warped) boundaries typically
needed for curved walls. You can also utilize special edge blends to smooth multiple adjacent warped
images into a single large seamless display.
KITS REQUIRED
• CD containing:
• ChristieTWIST™ PC application
• ChristieTWIST™ Install and Users Guide
• ChristieTWIST™ Warping Module PCB
• KoRE 10-Bit Librarian Setup PC application (available at www.christiedigital.com)
• warp_20.rff (available at www.christiedigital.com)
• Projector software 1.9C119 or higher
• Blower fan assembly
• (5) M3x6mm screws
• (4) washers
• (1) M3x16mm stand-off
TOOLS REQUIRED
• Phillips™ #1, #2
• 7/32” socket wrench
• adjustable wrench
INSTRUCTIONS
INSTALLING THE MODULE
The ChristieTWIST™ Warping Module is
installed onto the projector's TIPM (10-bit
Image Processing Module).
1. Turn the projector OFF and wait for
cooling fans to stop.
2. Disconnect all power sources to the
projector.
3. Remove the (6) #2 screws surrounding
the TIPM faceplate and slide out the
TIPM assembly.
NOTE: On earlier units with no handles on
the drawer, remove the projector lid and
push the drawer out from within. Do not pull
on exterior connectors.
2 of 8
FIGURE 1 ACCESSING THE TIPM FOR INSTALLING
CHRISTIETWIST
Roadie ChristieTWIST™ Warping Module Installation Instruction Sheet
020-100615-02 Rev. 1 (11-2010)
4.
Install the ChristieTWIST™ Warping Module
a. Align the Warping Module to the four TIPM stand-offs, taking care to mate the single large
connector. Refer to Figure 2 Warping Module Installation - Top.
b. Carefully press the module into place and secure to the TIPM using the 4 of the screws and
washers provided. Refer to Figure 2 Warping Module Installation - Bottom.
FIGURE 2 WARPING MODULE INSTALLATION
INSTALLING BLOWER ASSEMBLY
The Warp blower assembly provides enhanced cooling to the Warp Module heatsink. This
considerably lowers thermal stress on the board and will increase reliability of the module.
1. Swap Backplane Screw For Stand-Off
a. Remove the #1 screw indicated by the red arrow in Figure 3 Replace #1 Screw with 16mm
Stand-Off.
Roadie ChristieTWIST™ Warping Module Installation Instruction Sheet
020-100615-02 Rev. 1 (11-2010)
3 of 8
b. Replace the screw with the 16 mm stand-off provided with the kit and gently tighten it.
FIGURE 3 REPLACE #1 SCREW WITH 16MM STAND-OFF
2. Attach blower assembly Via Center Screw
a. Move blower assembly into position, lining up the three mounting points.
b. Loosely install center screw provided in the kit (not the previously removed screw). Center
screw is marked by the red arrow in Figure 4 Install Center Screw.
c. Loosely install the nuts on the two stand-off’s on the bottom of the TIPM.
d. Gently tighten the screw and 2 nuts indicated with red arrows in Figure 5 and Figure 5 Tighten
Screw and Nuts.
FIGURE 4 INSTALL CENTER SCREW
FIGURE 5 TIGHTEN SCREW AND NUTS
3. Plug In Fan Power Connectors
a. Plug each fan connector into the TIPM connectors
P23 and P24 shown in Figure 6 Plug In Fan
Power.
b. The longer harness plugs into P24, the shorter harness into P23 (No electrical difference)
4. Visual Inspection of Blower Kit Installation
a. Check that the screw and two nuts are tight.
b. Check that the plate is parallel to the TIPM PCB.
c. Check that both fan harnesses are fully seated.
FIGURE 6 PLUG IN FAN POWER
4 of 8
Roadie ChristieTWIST™ Warping Module Installation Instruction Sheet
020-100615-02 Rev. 1 (11-2010)
d. Check that the harnesses do not protrude past the edge of the plate as indicated by the red
arrow below. Refer to Figure 7 Inspection of Blower Kit Installation.
FIGURE 7 INSPECTION OF BLOWER KIT INSTALLATION
5. Re-Install TIPM Card Cage
a. Line up edges of TIPM with the guides.
b. Gently push TIPM Card Cage into the projector. Extra caution needs to be taken when blowers
are passing the inlet of the projector as Blower Kit has reduced clearance.
c. If cage catches then gently bias the card cage towards the front of the projector.
d. Once fully inserted into the projector apply a firm force to seat the TIPM with the backplane.
e. Re-install (6) #2 screws around the edges of the cage.
INSTALLING SOFTWARE
ON YOUR PC
Install the ChristieTWIST™ software application provided on the CD shipped with the module. For
instructions, refer to the ChristieTWIST™ Install and Users Guide included on the CD.
Install the KoRE Librarian setup v1.2 (or higher) software application. This can be downloaded from
www.christiedigital.com. For instructions, refer to the Using KoRE 10-Bit Librarian Upgrade
Instructions.pdf file for details.
IN THE PROJECTOR
Follow the typical main software installation/update process and install version 1.9D. If version 1.9D
or higher is not available install version 1.9C119.
INSTALL WARP SOFTWARE 2.0
Use KoRE Librarian to install the Warp Software (warp_20.rff) onto the projector. This can be
downloaded from www.christiedigital.com.
USING CHRISTIETWIST™ PROJECTOR CONTROLS
NOTE: The following section describes projector software only. Refer to separate documentation such
as the ChristieTWIST™ Install and Users Guide for information about using the PC application for
defining custom image warps.
Roadie ChristieTWIST™ Warping Module Installation Instruction Sheet
020-100615-02 Rev. 1 (11-2010)
5 of 8
The ChristieTWIST™ Warping Module and software enables a new Geometry and Color menu for
accessing additional Keystone and Warping controls in the projector.
FIGURE 8 GEOMETRY AND COLOR
KEYSTONE AND WARPING
Use the Keystone and Warping submenu to shape your images using new corner points and/or to apply
customized curved image boundaries called “warps”.
FIGURE 9 KEYSTONE AND WARPING
WARP SELECT
Choose a type of image shaping to apply, or choose to disable these adjustments. Note: Settings apply
to all sources:
• Disabled: Display standard (rectangular) images with no warping or keystone adjustments applied.
• 2D Keystone: Move 4 corners of the image to correct for a keystoned image and/or to create an
unusual 4-sided image exhibiting perspective or distortion. See 2D Keystone, below.
• User 1-10: Note: The user-defined options are titled User 1-10 by default; they can be changed using
the ChristieTWIST™ Software. Apply a custom image shape or twist that has been defined in the
ChristieTWIST™ PC application and downloaded to projector memory, typically creating one or
6 of 8
Roadie ChristieTWIST™ Warping Module Installation Instruction Sheet
020-100615-02 Rev. 1 (11-2010)
more “squeezed” or stretched areas in the display. If no custom warps have been created, the User
options will have no effect.
FIGURE 10 WARP SELECT
2D KEYSTONE
Move one or more corner points
as desired for your application.
Traditionally, keystoning
adjustments simply correct an
image in which opposing sides
are inclined away from each
other (caused by tilting the
projector in relation to the
screen). If the lens surface is
parallel to the screen and settings
are 50.0, the image should appear
rectangular. Alternatively, move
the corner points as desired to
create a specific 4-sided image in
which corners are up to 25%
closer to the center of the image,
or which are cropped off.
WARP PRE-FILTER
HORIZONTAL: Adjust as
desired to smooth or sharpen
side-to-side clarity in a warped
image. An increase will appear to
blur horizontal lines.
FIGURE 11 MOVING THE CORNERS FOR 2D KEYSTONE
WARP PRE-FILTER VERTICAL: Adjust as desired to smooth or sharpen top-to-bottom clarity in a
warped image. An increase will appear to blur vertical lines.
WARP SHARPNESS: Adjust as desired to soften or sharpen the overall image, similar to a Detail
adjustment.
WARP LATENCY: Set the percentage of frame delay (default = 50.0) desired for displaying incoming
data. A higher or lower setting will typically be needed with significant warps, ensuring that the entire
Roadie ChristieTWIST™ Warping Module Installation Instruction Sheet
020-100615-02 Rev. 1 (11-2010)
7 of 8
image appears. Warp latency also provides a means of synchronizing one display with adjacent
displays or other equipment such as audio.
BLENDING
Choose a type of image blending to apply, or choose to disable these
adjustments. Note: Settings apply to all sources:
• Disabled: This setting provides no Blending options.
• Standard: This setting activates the standard edge blending functionality to the projector without the warp board and is not intended
for use with warped images. Please refer to your projector's Users
FIGURE 12 BLENDING
Guide for further details.
• User 1-5: Note: The user-defined options are titled User 1-5 by default; they can be changed using
the ChristieTWIST™ Software. Apply a custom edge blend, generated and defined in the ChristieTWIST™ PC application and downloaded to projector memory, typically creating one or more
types of edge blend. If no custom blends have been created, the User options will have no effect.
NOTE: If a ChristieTWIST™ Warping Module is installed, the Edge Blending menu controls are
expanded to include user-defined blends appropriate for a warped image. The new blend ranges are 080 for side blends, and 0-60 for top or bottom blends. If no warping is currently applied but you still
need to use edge blending for a tiled wall, select “Standard”.
NOTE: The installation of a Warping Module will disable the Black Level Blending feature on 3-chip
projectors.
8 of 8
Roadie ChristieTWIST™ Warping Module Installation Instruction Sheet
020-100615-02 Rev. 1 (11-2010)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising