WIRELESS OPERATION (TH

WIRELESS OPERATION (TH
WIRELESS OPERATION (TH-D72A ONLY)
If you also have a Kenwood multi-band mobile transceiver, you can control one of its bands by sending DTMF tones from
this handy transceiver. You will find this function useful when you want to control your mobile transceiver from a location
outside your vehicle.
Note:
u You can remotely control only mobile transceivers that have both the secret number and Remote Control functions.
u FCC rules permit you to send control codes only on the 440 MHz band.
PREPARATION
CONTROL OPERATION
Let us assume the VHF band of the mobile transceiver will
be controlled.
When in Remote Control mode, the keys of the handy
transceiver will function as described below. Each time
you press a key, the handy transceiver will automatically
transmit the corresponding command to the mobile
transceiver.
On the handy transceiver:
1 Press [PTT] + [VFO] + Power ON.
• The current secret access code number appears. The
default is 000.
ON 1
TONE ON
CTCSS ON
ENT
OFF
TONE OFF
CTCSS OFF
TONE SEL
CALL
VFO
MR
REP ON 2
DOWN
LOW
UP
REP OFF 2
1
TM-V7/ TM-D700: Revers ON/ OFF
TM-D710/ TS-2000: DCS ON/ OFF
Other than TM-V7/ TM-D700/ TM-D710/ TS-2000:
Tone Alert ON/ OFF.
2
Switches Cross-band Repeater ON/ OFF if the mobile
transceiver has this function.
1
2 To change the secret number, press the numeric keys
(0 to 9) to enter a 3-digit number.
• You can also press [ ]/[ ] to select each digit. Press
[ OK] (or [ESC ]) to move the cursor to the next (or
previous) digit.
To change the transmit/ receive frequency:
3 Press [ OK] to complete the setting.
([VFO] ➡ [ENT] ➡ [0] ~ [9] (enter the necessary digits)➡
[ENT]) or ([VFO] ➡ [ ]/[ ])
4 Select the UHF band.
5 Select the transmit frequency.
To recall a memory channel:
6 Turn the transceiver power OFF.
([MR] ➡ [ENT] ➡ [0] ~ [9] (enter the necessary digits) ➡
[ENT]) or ([MR] ➡ [ ]/[ ])
7 Press [PTT] + [MR] + Power ON.
• The transceiver enters Remote Control mode. “Mobile
Ctrl” appears.
• To exit Remote Control mode, repeat steps 6 and 7.
On the mobile transceiver:
To change the tone (or CTCSS) frequency:
([TONE SEL] ➡ [0] ~ [9] (enter 2 digits; ex. [0], [5]) ➡
[TONE SEL])
• Use Nos. 01 to 42, as shown in the CTCSS table.
• Your mobile transceiver may require you to first activate the
Tone or CTCSS function. It may also allow you to program a
separate tone and CTCSS frequency. Check the instruction
manual for the mobile transceiver.
8 Set the ID code to the same secret number you set on
the handy transceiver.
• For the method, refer to the instruction manual for the
mobile transceiver.
9 Select the receive frequency on the UHF band.
• Match this frequency with the transmit frequency of the
handy transceiver.
10Enter the transceiver’s Remote Control mode.
• For the method, refer to the instruction manual for the
mobile transceiver. If it is not described, consult your
authorized Kenwood dealer, customer service, or service
center.
WIRELESS OP – 
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising