166-Bottle Dual Zone Wine Cellar

166-Bottle Dual Zone Wine Cellar
166-Bottle Dual Zone Wine Cellar
INSTRUCTION MANUAL
PLEASE READ THIS MANUAL CAREFULLY BEFORE INSTALLING AND OPERATING.
Important Note:
Upper zone must be set 4°F colder than lower zone.
1
TABLE OF CONTENTS
Contents
____Page #
Diagram & Description of Wine Cellar
3
Important Safety & Pre-Use Instructions
4
Installation Instructions
(a) General Installation Instructions
(b) Installation of Built-In Unit
(c) Reversing Door Swing
4
5
6
Operating Your Wine Cellar
7
Temperature Settings
8
Layout & Storage
9
Removing the Rolling Shelf
9
Care & Maintenance
9
Troubleshooting Guide
11
Technical Information
12
Warranty Information
12
2
DIAGRAM & DESCRIPTION OF WINE CELLAR
YOUR WINE CELLAR ALSO INCLUDES THE FOLLOWING:
Instruction manual
15 rolling shelves
Two (2) keys
Top and bottom hinges/screws (for changing the door hinge)
3
IMPORTANT SAFETY INSTRUCTIONS
To reduce the risk of fire, electrical shock, or injury when
WARNING
using your appliance, follow these basic precautions:

Read all instructions before using the wine cellar.

DANGER: Risk of child becoming trapped in new cellar, old wine cellar/refrigeration unit, or large boxes.
Junked or abandoned appliances, boxes and other containers are still dangerous, even if they will “just sit in
the garage for a few days”.

Before you throw away your old wine cellar or refrigeration unit: 1. Take off the door. 2. Leave the
shelves in place so that children cannot climb inside.

Never allow children to operate, play with, or crawl inside the appliance.

Never clean appliance parts with flammable fluids. The fumes can create a fire hazard or explosion.

Do not store in the vicinity of any other appliance. Do not store near gasoline or any other flammable vapors.
The fumes can create a fire hazard or explosion.
-Save these instructions-
BEFORE USING YOUR WINE CELLAR

Remove the exterior and interior packaging.

Before connecting the wine cellar to the power source, let it stand upright for approximately 2 hours. This
will reduce the possibility of a malfunction in the cooling system from handling during transportation.

Clean the interior surface with lukewarm water using a soft cloth.
INSTALLATION INSTRUCTIONS
(a) General Installation Instructions

This appliance is designed for free standing installation or can be recessed into cabinetry.

Place your wine cellar on a flat, solid floor that is strong enough to support it when it is fully loaded. To level
your wine cellar, adjust the front leveling leg at the bottom of the wine cellar.

When moving your wine cellar, please do not incline it more than 45 degrees.

Locate the wine cellar away from direct sunlight and sources of heat (stove, heater, radiator, etc.). Direct
sunlight may affect the acrylic coating and heat sources may increase electrical consumption. Extreme
cold ambient temperatures may also cause the unit to perform improperly.

Avoid locating the unit in damp areas.

Plug the wine cellar into a dedicated (for this appliance only), properly installed and grounded wall outlet.
Do not under any circumstances cut or remove the third (grounding) prong from the power cord. Any
questions concerning power and/or electrical grounding should be directed to a certified electrician or
authorized product service center.
4
(b) Installation of Unit as a Built-In Cellar
The cutout dimensions illustrated below allows for door clearance and access to the pull-out shelves when installed
as a built-in appliance.
Your wine cellar has been manufactured with a zero clearance door so no extra space is required to account for the
door swing when building into cabinetry.
.
These cut out dimensions show the minimum space required for your wine cellar to perform as designed.
5
(c) Reversing the Door Swing of Your Appliance
Before you begin: Tape down shelves to avoid movement during the process
The unit may have been delivered to you with the door opening from the left side (hinges on the right).
The door of this appliance can be hung to open on the left or right side. To reverse the door swing of your
cooler and open from the opposite side, please follow the instructions and diagram below.
1.
Pry up the hinge cover (1) and hinge cap (2) using a flat head screwdriver.
loosen the hinge screws (3a) and remove the top hinge (4).
and set it off to one side.
will need this later.
Using a Phillips head screwdriver,
You can now lift the door (5) off the bottom hinge
Be careful not to lose the washer (11) between the bottom hinge and the door.
Also remove lock hole cap (6) and screws (7) and (8) from the top of the door.
You
The lock
cap can be pried up using a small flat head screwdriver.
2.
Using a Phillips head screwdriver, loosen screws (3b) to remove the hinge support rod (9) at the bottom of the
door.
Rotate the door 180° so that the top is now the bottom and vice versa.
6
Attach the bottom hinge support
rod (9) to the bottom corner of the door and attach with screws (3b).
3.
Using a flat head screwdriver, pry off the bottom hinge cover (12).
Using a Phillips head screwdriver, loosen
and remove screws (3c) and (13) and bottom hinge (10).
4.
Move bottom hinge (10) to the opposite side and re-insert all screws (3c) and (8).
Bottom hinge cover (12)
should clip back onto the bottom hinge (10).
5.
Place the washer (11) over the hinge support rod (9) and place the door back on the bottom hinge by aligning the
hinge support rod (9) with the outer hinge hole on bottom hinge (10).
6.
Re-attach top hinge (4) using screws (3a).
Insert lock cap (6), screws (7) and (8), and clip on hinge cap (2).
Stainless steel doors include a handle centered in the middle of the door.
There is no need to alter the location of the
handle.
Glass doors include integrated door pull handles.
There is no need to alter the location of door pull handles.
OPERATING YOUR WINE CELLAR
Each wine cellar includes an operating panel on the front of the unit. This operating panel includes several features to
operate and control the temperature of both the UPPER and LOWER zones of the wine cellar. The operating panel
includes the following features:
Power:
Turns the wine cellar system on or off.
Lighting:
Turns the interior wine cellar light on or off.
Power/Lighting:
Lock/Unlock button.
°C/°F:
Alters the temperature display to Fahrenheit or Celsius
Upper Zone Display Window:
Displays temperature of upper zone.
Bottom Zone Display Window:
Displays temperature of lower zone.
Temp. Up
Increases temperature by 1°.
Temp. Down
Decreases temperature by 1°.
Zone Select:
Switches temperature control between upper and lower zone.
BEFORE YOU START:
The wine cellar should be placed in a location where the ambient temperature is between
60-80° Fahrenheit. If the ambient temperature is outside this range, the performance of the unit may be affected. For
7
example, placing your unit in extreme cold or hot conditions may cause interior temperatures to fluctuate.
IMPORTANT: IN ORDER FOR THIS UNIT TO FUNCTION AT OPTIMUM LEVEL, THE UPPER COMPARTMENT
SHOULD BE SET AT LEAST 4-DEGREES (F) COLDER THAN THE LOWER COMPARTMENT.
Lock/Unlock
Your wine cellar includes a feature that will lock the control panel when if left untouched for 10 seconds.
To unlock
the wine cellar control panel touch the power and lighting buttons simultaneously for 10 seconds.
Setting Temperature
1. Make sure power cord is connected to a properly grounded outlet.
2. Turn power ON.
3. Press the zone select button to choose the “UPPER” or “LOWER” zone.
Each zone is independently
controlled.
Upper Zone: The temperature setting can be adjusted from 41°F to 54°F
Lower Zone: The temperature setting can be adjusted from 46°F to 66°F
4. Set the desired temperature of the UPPER or LOWER zone pushing the UP (
5. Temperatures increase or decrease 1°F with each push of the UP (
+ ) or DOWN ( - ) button.
+ ) or DOWN ( - ) button.
6. NOTE: Temperatures may fluctuate depending on whether the interior light is ON or OFF and depending on the
position of the bottles.
TEMPERATURE SETTINGS FOR SERVING WINE
1. Although optimal storage temperature is generally regarded to be 53-57°F, different varietals of wine have
different recommended serving temperatures for optimal taste.
serving different varietals of wine are listed below.
The recommended temperature ranges for
Your wine cellar will indicate when you have set the
Upper/Lower zones to the below temperature ranges.
Red Wines:
60-66°F
White Wines
45-52°F
Sparkling Wines
40-45°F
NOTE:

In the event of a power interruption, your wine cellar will revert back to the factory settings, 50° F in the upper
cabinet and 61° F in the lower cabinet, once power is restored.

If the unit is unplugged, loses power, or is turned off, you must wait 3 to 5 minutes before restarting.
Attempting to restart the wine cellar before this time has elapsed may prevent the wine cellar from starting.

When you use the wine cellar for the first time or restart the wine cellar after having been shut off for a long time,
there will be a few degrees variance between the temperature you select and the one indicated on the LED
readout for the first few hours of operation. After a few hours of operation, the temperature will normalize to the
displayed temperature.
DOOR LOCK

This unit comes with key lock.

The keys are located inside the plastic bag that contains the user manual. To unlock the door, insert the key into
the lock and turn counter clockwise.

To lock the door, simply reverse the operation making sure the metal pin is engaged completely. Then remove
8
the key and place it is a secure place for safekeeping.
LAYOUT AND STORAGE
Your cabinet was designed to store a maximum number of bottles securely. We recommend that you observe the
tips below to optimize loading.
Remove tape from shelves once unit is stable and ready for storage.
Disperse the bottles evenly to avoid concentrating weight in one place. Bottles must not touch either the back of
the cabinet or the step at the bottom.
While your wine cellar was designed to hold large format bottles such as
Pinot Noir and Champagne, these larger bottles reduce the number of bottles you can fit on 1 shelf.
that the bottles are not all grouped together either at the top or bottom of the cabinet.
Make sure
Bottles dispersed evenly
throughout the cabinet will contribute to optimal cooling.
Only pull out one rolling shelf at a time. Never attempt to pull more than one.
Maximum weight capacity per shelf is 55 lbs.
Each rolling shelf is designed to comfortably hold one row of 11-13 bottles.
REMOVING THE ROLLING SHELF
To remove a rolling shelf:
1.
2.
3.
4.
Remove all bottles.
Pull the shelf out as far as it will go.
Push the left side lever downward while pushing the right side lever upwards (as illustrated below).
Remove the shelf.
CARE AND MAINTENANCE
Cleaning Your Wine Cellar

Turn off the power, unplug the appliance, and remove all items including all shelves.

Wash the inside surfaces with a solution of warm water and baking soda (approximately 2 tablespoons of baking
soda for each quart of water.)

Wash the shelves with a mild detergent solution.

Wring excess water out of the sponge or cloth when cleaning area of the controls, or any electrical parts.

Wash the exterior with warm water and mild liquid detergent. Rinse well and wipe dry with a clean soft cloth.

Vacuum the front grill and back of the unit twice yearly. Make sure the power is off before cleaning.

It is recommended to clean the unit completely inside and out once a year to maximize the longevity of the wine
cellar.
9
Power Loss

Power failures that are corrected within a few hours should not affect the temperature of your appliance if you
minimize the number of times the door is opened. If the power is going to be off for a longer period of time, you need
to take other measures to protect your contents.

If the unit is unplugged, loses power, or is turned off, you must wait 3 to 5 minutes before restarting. Attempting to
restart the wine cellar before this time has elapsed may prevent the wine cellar from starting.
Absence/Vacation

Short vacations: You may leave the wine cellar powered on and unattended for absences of less than three (3)
weeks.

Long vacations: If the appliance will not be used for more than three weeks, remove all items and turn off the
appliance. Clean and dry the interior thoroughly. To prevent mold growth, leave the door open slightly, blocking it
open if necessary.
Moving Your Wine Cellar

Remove all items.

Securely tape down all loose items (shelves) inside your appliance.

Turn the adjustable leg up to the base to avoid damage.

Tape the door shut.

Be sure the appliance stays secure in the upright position during transportation. Also protect the outside of the
appliance with a blanket or similar item.
Energy saving Tip

The wine cellar should be located in the coolest area of the room, away from heat producing appliances, and away
from direct sunlight.
10
TROUBLESHOOTING GUIDE
Many common issues with your wine cellar can be solved very easily.
Try the troubleshooting tips below should you
experience any problems.
PROBLEM
Wine cellar does not operate.
POSSIBLE CAUSE
Not plugged in.
The appliance is turned off.
The circuit breaker tripped or a fuse has blown out.
Wine cellar is not cold enough.
Check the temperature control setting.
External environment may require a higher setting. (e.g. room
needs to be air conditioned)
The door is opened too often.
The door is not closed completely.
The door gasket is not sealing properly.
Wine cellar is turning on and off frequently.
The room temperature is hotter than normal.
The door is opened too often.
The door is not closed completely.
The temperature control is not set correctly.
The door gasket does not seal properly.
The light does not work.
Not plugged in.
The circuit breaker tripped or a fuse has blown.
The light bulb has burned out.
The light button is “OFF”.
Vibrations.
Check to assure that the wine cellar is on a level surface.
The wine cellar seems to make too much noise.
A faint humming noise may come from the flow of the
refrigerant, which is normal.
As each cycle ends, you may hear gurgling sounds caused by
the flow of refrigerant in your wine cellar.
Contraction and expansion of the inside walls may cause
popping and crackling noises.
The wine cellar is not on a level surface.
The door will not close properly.
The wine cellar is not on a level surface.
The door was reversed and not properly installed.
The gasket is dirty.
The shelves are out of position.
The area around the door, top, or side is hot.
Your wine cellar comes with a heating element near the door
that keeps frost and condensation off the glass and it’s normal
for this area to feel warm.
inside the wine cellar.
11
It will not affect the temperature
TECHNICAL DATA
166 Bottle N’Finity Pro Wine Cellar
268 70
Accommodation
166
(bottles)
Type of cooling
compressor & air-circulated fan cooling
Climate type
N
Electricity protection grade
I
Nominal voltage/Frequency
115V/60HZ
Rated power(W)
255W
60-80 degrees Fahrenheit
Ambient temperature
Upper Zone: 41F - 54F
Temperature range
Lower Zone: 46F - 66F
Range of inside cabinet humidity
60%RH
Item weight
225 pounds
23 ¾”W X 27 ¼”D X 69 ¾”H
Item dimension
Stainless steel door handle will add 2” to depth
WARRANTY INFORMATION
Please speak to your retailer before calling Wine Enthusiast if you did not purchase your wine cellar directly from Wine
Enthusiast.
Limited warranty – 90-day replacement plan with a free 9-month upgrade, totaling 1 year, on parts and labor from the
date of shipment. For customer service, please contact Wine Enthusiast by e-mail (custserv@WineEnthusiast.net) or by
phone (800.648.6058).
The limited warranty does not cover: Damage due to such things as accident, misuse, abuse, mishandling, neglect,
unauthorized repair or any other cause beyond the control of the seller whether similar or dissimilar to the foregoing.
Purchaser understands and acknowledges that the goods sold here are wine refrigerators, which house wine. Purchaser
assumes all the risk of using these units, including risk of spoilage, humidity variations, temperature variations, leaks,
fires, water damage, mold, mildew, dryness and similar perils that may occur.
12
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising