OPERATION AND INSTALLATION

OPERATION AND INSTALLATION
OPERATION AND INSTALLATION
Wall mounted convector
»»
»»
»»
»»
»»
»»
»»
CNS
CNS
CNS
CNS
CNS
CNS
CNS
50 U
75 U
100 U
150 U
200 U
250 U
300 U
»»
»»
»»
»»
»»
»»
»»
»»
CNS
CNS
CNS
CNS
CNS
CNS
CNS
CNS
50 UT
75 UT
100 UT
125 UT
150 UT
200 UT
250 UT
300 UT
»»
»»
»»
»»
»»
CNS
CNS
CNS
CNS
CNS
75 UE
100 UE
150 UE
200 UE
300 UE
CONTENTS | Special information

OPERATION
SPECIAL INFORMATION
1.
1.1
1.2
1.3
1.4
General information�����������������������������������������3
Safety instructions����������������������������������������������� 3
Other symbols in this documentation����������������������� 3
Information on the appliance��������������������������������� 3
Units of measurement������������������������������������������ 3
-- Keep children under the age of 3 away from
the appliance if constant supervision cannot be
guaranteed.
2.
2.1
2.2
2.3
Safety����������������������������������������������������������3
Intended use������������������������������������������������������ 3
General safety instructions������������������������������������ 4
Test symbols������������������������������������������������������ 4
3.
Appliance description���������������������������������������4
4.
4.1
4.2
4.3
4.4
Operation�����������������������������������������������������4
CNS U�������������������������������������������������������������� 4
CNS UT������������������������������������������������������������� 5
CNS UE������������������������������������������������������������� 5
Limiting the temperature selector
(CNS U | CNS UE)������������������������������������������������� 6
5.
Cleaning, care and maintenance���������������������������6
6.
What to do if...������������������������������������������������6
SPECIAL INFORMATION
INSTALLATION
7.
7.1
7.2
Safety����������������������������������������������������������7
General safety instructions������������������������������������ 7
Instructions, standards and regulations�������������������� 7
8.
8.1
Appliance description���������������������������������������7
Standard delivery������������������������������������������������ 7
9.
9.1
9.2
9.3
9.4
9.5
Installation����������������������������������������������������7
Minimum clearances�������������������������������������������� 7
Installing the wall mounting bracket������������������������ 7
Appliance installation������������������������������������������� 8
Removing the appliance���������������������������������������� 8
Power supply����������������������������������������������������� 8
10.
Troubleshooting����������������������������������������������8
11.
Appliance handover������������������������������������������8
-- Children from the age of 3 to 7 may switch the
appliance on and off, provided they are supervised or have been instructed in the safe operation of the appliance and understand any risks
that may result. This is subject to the appliance
having been installed as described. Children from
the age of 3 to 7 must not plug the power cable
into its socket nor regulate the appliance.
-- The appliance may be used by children aged 8
and older and persons with reduced physical,
sensory or mental capabilities or a lack of experience and know-how, provided that they are supervised or they have been instructed on how to
use the appliance safely and have understood the
resulting risks.
-- Children must never play with the appliance. Children must never clean the appliance or perform
user maintenance unless they are supervised.
-- Parts of the appliance can get very hot and may
cause burns. Particular caution is advised when
children or vulnerable persons are present.
-- Never cover the appliance.
-- Never install the appliance directly below a wall
socket.
12. Specification��������������������������������������������������9
12.1 Dimensions and connections���������������������������������� 9
12.2 Data table��������������������������������������������������������� 9
-- Install the appliance in such a way that the control equipment cannot be touched by a person in
the bath or shower.
GUARANTEE
-- The connection to the power supply must be in
the form of a permanent connection. Ensure the
appliance can be separated from the power supply by an isolator that disconnects all poles with
at least 3 mm contact separation.
ENVIRONMENT AND RECYCLING
-- The power cable may only be replaced (for example if damaged) by a qualified contractor authorised by the manufacturer, using an original spare
part.
-- Secure the appliance as described in chapter "Installation / Installation".
2 | CNS U | CNS UT | UEwww.stiebel-eltron.com
Operation
General information
1.2 Other symbols in this documentation
Note
General information is identified by the adjacent symbol.
ff
Read these texts carefully.
1. General information
The chapters "Special Information" and "Operation" are intended
for both the user and qualified contractors.
The chapter "Installation" is intended for qualified contractors.
Symbol
Meaning
Material losses
(Appliance and consequential losses, environmental pollution)
Appliance disposal
!
Note
Read these instructions carefully before using the appliance and retain them for future reference.
Pass on the instructions to any new user if required.
ff
This symbol indicates that you have to do something. The action you need to take is described step by step.
1.1 Safety instructions
1.3 Information on the appliance
1.1.1 Structure of safety instructions
Symbol
!
Meaning
Never cover the appliance
KEYWORD Type of risk
Here, possible consequences are listed that may result
from failure to observe the safety instructions.
ff
Steps to prevent the risk are listed.
1.1.2 Symbols, type of risk
Symbol
!
Type of risk
Injury
Electrocution
Burns
(burns, scalding)
1.1.3 Keywords
KEYWORD
DANGER
WARNING
CAUTION
Meaning
Failure to observe this information will result in serious
injury or death.
Failure to observe this information may result in serious
injury or death.
Failure to observe this information may result in non-serious or minor injury.
www.stiebel-eltron.com
1.4 Units of measurement
Note
All measurements are given in mm unless stated otherwise.
2. Safety
2.1 Intended use
This appliance is designed to heat living areas.
This appliance is intended for domestic use. It can be used safely
by untrained persons. The appliance can also be used in a non-domestic environment, e.g. in a small business, as long as it is used
in the same way.
Any other use beyond that described shall be deemed inappropriate. Observation of these instructions and of instructions for any
accessories used is also part of the correct use of this appliance.
CNS U | CNS UT | CNS UE | 3
ENGLISH
OPERATION
Operation
Appliance description
2.2 General safety instructions
2.3 Test symbols
Operate the appliance only when fully installed and with all safety
equipment fitted.
See type plate on the right on the exterior of the appliance.
!
WARNING Injury
-- Keep children under the age of 3 away from the
appliance if constant supervision cannot be guaranteed.
-- Children from the age of 3 to 7 may switch the appliance on and off, provided they are supervised
or have been instructed in the safe operation of
the appliance and understand any risks that may
result. This is subject to the appliance having been
installed as described. Children from the age of 3 to
7 must not plug the power cable into its socket nor
regulate the appliance.
-- The appliance may be used by children aged 8 and
older and persons with reduced physical, sensory
or mental capabilities or a lack of experience and
know-how, provided that they are supervised or
they have been instructed on how to use the appliance safely and have understood the resulting risks.
-- Children must never play with the appliance. Children must never clean the appliance or perform
user maintenance unless they are supervised.
3. Appliance description
The appliance is a wall mounted electric direct heater.
The appliance is suitable as a full heating system in bathrooms,
for example, or for use between seasons and as a booster heater
in smaller rooms, such as hobby and guest rooms.
The air in the appliance is heated by a heating element and expelled via natural convection through the air outlet grille at the
top. Cool room air flows in through the apertures at the bottom
of the appliance.
After mounting the appliance on the wall and making the electrical connection using a permanent power supply via an appliance
socket, the appliance is ready for operation.
4. Operation
4.1 CNS U
1
2
WARNING Burns
Never operate this appliance...
-- in rooms where the appliance is at risk of fire or
explosion as a result of chemicals, dust, gases or
vapours.
-- in the direct proximity of pipes or receptacles that
carry or contain flammable or explosive materials.
-- if work such as laying cables, grinding or sealing is
carried out in the installation room.
-- if sprays, floor polish or similar products containing
napsan are used. Ventilate the room sufficiently
before heating.
-- if the minimum clearances to adjacent object surfaces are not maintained, for example to furniture,
net curtains, curtains, textiles or other flammable
materials.
-- if an appliance component is damaged, the appliance has fallen over or already had a fault.
WARNING Burns
Never place any flammable, combustible or insulating
objects or materials, such as laundry, blankets, magazines, containers with floor polish or napsan, spray cans
or similar on the appliance or in direct proximity to it.
WARNING Burns
Parts of the appliance can get very hot and may cause
burns. Particular caution is advised when children or
vulnerable persons are present.
!
26_07_31_0037
1 Temperature selector
2 ON/OFF switch
4.1.1 Switching the appliance on and off
ff
Switch the appliance on and off via the ON/OFF switch on the
right hand side of the appliance.
4.1.2 Temperature selector
ff
Set the required room temperature via the continuously
variable temperature selector (for setting range see chapter
“Specification / Data table”).
As soon as the selected room temperature is reached, it is constantly maintained at this selected temperature through periodic
heating. The output of the appliance must correspond at least to
the required heat demand of the room.
If several appliances are installed in a single room, the setting
at the temperature selector on each appliance can be different.
Note
To avoid excessive power consumption when windows
are open, switch the appliance off while airing.
CAUTION Overheating
Never cover the appliance.
Material losses
Never step on the appliance.
4 | CNS U | CNS UT | UEwww.stiebel-eltron.com
4.1.3 Frost protection
ff
Turn the temperature selector as far to the right as possible.
Constant operation "I"
ff
Move the ON/OFF switch to "I".
In this position, the temperature controller switches on the heating
element automatically if the room temperature drops below the
frost protection temperature.
The appliance heats with no time limit until the room temperature set with the temperature selector is reached. As soon as the
selected room temperature is reached, it is constantly maintained
at this selected temperature through periodic heating. The output
of the appliance must correspond at least to the required heat
demand of the room.
4.2 CNS UT
1
Frost protection is always enabled.
4
12
If several appliances are installed in a single room, the setting
at the temperature selector on each appliance can be different.
13
3
1
2
3
4
4.3 CNS UE
Time switch
Temperature selector
ON/OFF switch
Arrow marking the time
4.2.1 Temperature selector
ff
Set the required room temperature via the continuously
variable temperature selector (for setting range see chapter
“Specification / Data table”).
1
3
4.2.2 Operating modes
Heating with the time switch
ff
The appliance heats in accordance with the time switch settings until the room temperature set with the temperature
selector is reached. Frost protection is only enabled during
the selected time.
ff
Set the time by turning the time switch clockwise until the
black arrow points to the current time.
ff
Push the tabs on the edge of the time switch outwards according to the times when the appliance should heat. Every
tab corresponds to an ON or OFF period of 20 minutes.
-- Heating ON: Push the tabs outwards.
-- Heating OFF: Push the tabs inwards.
2
26_07_31_0174
2
26_07_31_0236_
14
Note
To avoid excessive power consumption when windows
are open, switch the appliance off while airing.
1 ON/OFF switch
2 Temperature selector
3 Operating mode switch
4.3.1 Switching the appliance on and off
ff
Switch the appliance on and off via the ON/OFF switch on the
right hand side of the appliance.
4.3.2 Temperature selector
ff
Set the required room temperature via the continuously
variable temperature selector (for setting range see chapter
“Specification / Data table”).
Appliance off "0"
ff
To switch the appliance off, move the ON/OFF switch to "0".
In this operating mode, frost protection is also disabled.
www.stiebel-eltron.com
CNS U | CNS UT | CNS UE | 5
ENGLISH
Operation
Operation
Operation
Cleaning, care and maintenance
4.3.3 Operating modes
Comfort mode
2
As soon as the selected room temperature is reached, it is constantly maintained at this selected temperature through periodic
heating. The output of the appliance must correspond at least to
the required heat demand of the room.
If several appliances are installed in a single room, the setting
at the temperature selector on each appliance can be different.
Note
To avoid excessive power consumption when windows
are open, switch the appliance off while airing.
ECO mode (night setback)
On this setting the comfort temperature set at the temperature
selector is automatically reduced by 3 °C.
Frost protection
In this position, the temperature controller switches heating on
automatically if the room temperature drops below the frost protection temperature.
Automatic
If the appliance is connected to an optional control device, you
can use this to operate it. Depending on the setting of the control
device, the appliance heats at certain times of the day in comfort,
ECO or frost protection mode.
If the appliance is not connected to a control device, the appliance
heats in comfort mode.
4.4 Limiting the temperature selector
(CNS U | CNS UE)
Using the two pins fitted to the back of the control casing, you
can fix the temperature selector at a certain setting or limit the
temperature setting range.
ff
Break out the pins.
1 Pin
2 Temperature selector
ff
To limit the temperature setting range, set the minimum and
maximum values at the temperature selector, and push a pin
for each into the slightly offset hole opposite.
5. Cleaning, care and maintenance
CAUTION Burns
-- Never spray cleaning spray into the air slot.
-- Ensure that no moisture can enter the appliance.
ff
If a pale brownish discolouration appears on the appliance
casing, wipe it off with a damp cloth.
ff
Clean the appliance when cold with ordinary cleaning products. Avoid abrasive or corrosive cleaning products.
Note
As part of regular maintenance, we recommend also
having the control components checked. The safety and
control components should be checked by a contractor
no more than ten years after commissioning.
6. What to do if...
... the appliance does not heat up:
ff
Check the temperature set at the appliance and the MCB/fuse
in your fuse box.
The appliance has a safety temperature controller that shuts the
appliance down if it overheats. After the cause has been removed
(for example air outlet or inlet apertures covered) and the appliance has cooled down for a few minutes, operation starts again.
2
If you cannot remedy the fault, notify your qualified contractor.
To facilitate and speed up your enquiry, please provide the serial
number from the type plate (000000-0000-000000).
26_07_31_0038
1
1
1
26_07_31_0171
1
1 Pin
2 Temperature selector
ff
To fix the selected temperature, push a pin into the hole opposite .
6 | CNS U | CNS UT | UEwww.stiebel-eltron.com
Installation
Safety
9. Installation
ENGLISH
INSTALLATION
9.1 Minimum clearances
7. Safety
7.1 General safety instructions
≥150
Only a qualified contractor should carry out installation, commissioning, maintenance and repair of the appliance.
≥100
≥100
≥500
We guarantee trouble-free function and operational reliability only
if original accessories and spare parts intended for the appliance
are used.
WARNING Electrocution
Install the appliance in such a way that control equipment
cannot be touched by a person in the bath or shower.
CAUTION Burns
-- Only fit the wall mounted appliance to a vertical
wall that is temperature-resistant to at least 85 °C.
-- Maintain the minimum clearances to adjacent object
surfaces.
!
D0000019283
≥100
≥20
9.2 Installing the wall mounting bracket
Note
You can also use the wall mounting bracket as a template for wall mounting; this ensures the required floor
clearance.
Material losses
-- Never install the appliance directly below a wall
socket.
-- Ensure that the power cable is not in contact with
any appliance components.
3
4
7.2 Instructions, standards and regulations
Note
Observe all applicable national and regional regulations
and instructions.
1
2
8.1 Standard delivery
The following are delivered with the appliance:
-- Wall mounting bracket (hooked into the appliance)
a
26_07_31_0124
8. Appliance description
ff
Unhook the wall mounting bracket.
ff
Place the centred wall mounting bracket level on the ground
and mark holes 1 and 2.
ff
Lift up the wall mounting bracket so that its lower holes
match up with the markings you have just made on the installation wall.
ff
Mark holes 3 and 4 on the installation wall.
ff
Drill holes at all four markings.
ff
Secure the wall mounting bracket with suitable materials
(screws, rawl plugs) depending on the type of wall. With the
vertical slots, you can compensate for an offset fixing hole.
www.stiebel-eltron.com
CNS U | CNS UT | CNS UE | 7
Installation
Troubleshooting
9.3 Appliance installation
9.5 Power supply
ff
Hook the appliance by its slots in the back of the appliance on
to all four tabs of the wall mounting bracket simultaneously.
ff
Push the appliance to latch it in position.
ff
Ensure the on-site supply cable has an adequate
cross-section.
ff
When connecting the appliance via a standard socket, ensure
that the socket is easily accessible once the appliance has
been installed.
1
26_07_31_0035
2
1 Locking bolt
2 Wall mounting bracket
ff
Turn the locking bolt in the wall mounting bracket fully clockwise; this locks the appliance in place.
2
Note
Observe the type plate. The specified voltage must match
the mains voltage.
9.5.1 CNS-UE
ff
With a permanent connection, connect the three-core cable
to a junction box as follows.
26_07_31_0127
3
1 Appliance
2 Safety cap
3 Locking bolt
ff
Push the safety cap onto the locking bolt to prevent it from
loosening.
1
2
3
1
2
3
1 Neutral = blue
2 Live = brown
3 Control cable = black
10. Troubleshooting
The power cable must only be replaced by a qualified contractor
using original spare parts supplied by us.
9.4 Removing the appliance
1
26_07_31_0175
1
WARNING Electrocution
-- Carry out all electrical connection and installation
work in accordance with relevant regulations.
-- Ensure the appliance can be separated from the
power supply by an isolator that disconnects all
poles with at least 3 mm contact separation.
-- Do not install the appliance with a fixed power
cable.
-- Never install the appliance directly below a wall
socket.
11. Appliance handover
2
Explain the functions of the appliance to the user. Draw special
attention to the safety instructions. Hand over the operating and
installation instructions to the user.
26_07_31_0128
3
1 Appliance
2 Safety cap
3 Locking bolt
ff
Remove the safety cap from the locking bolt.
ff
Undo the locking bolt on the wall mounting bracket.
ff
Lift the appliance up slightly and pull it forwards and away
from the wall mounting bracket.
8 | CNS U | CNS UT | UEwww.stiebel-eltron.com
Installation
Specification
ENGLISH
12. Specification
12.1 Dimensions and connections
a20
D0000019277
b01
i13
a20 Appliance
Width
b01 Electrical cable entry
i13 Wall mounting
Hole spacing
bracket
mm
CNS 50
U/UT
370
mm
121
CNS 75
U/UT/UE
445
195
CNS 100 CNS 125 UT
U/UT/UE
445
590
195
343
CNS 150
U/UT/UE
590
CNS 200
U/UT/UE
740
343
491
CNS 250
U/UT
890
639
CNS 300
U/UT/UE
1040
787
12.2 Data table
CNS 50-300 U
CNS 50 U
236276
Electrical data
Connected load
Power supply
Dimensions
Height
Width
Depth
Weights
Weight
Versions
IP rating
Protection class
Colour
kW
CNS 75 U
236277
CNS 100 U
236278
CNS 150 U
236279
CNS 200 U
236280
CNS 250 U
236281
CNS 300 U
236282
0.5
0.75
1.0
1.5
2.0
2.5
3.0
1/N ~ 240 V 50 Hz 1/N ~ 240 V 50 Hz 1/N ~ 240 V 50 Hz 1/N ~ 240 V 50 Hz 1/N ~ 240 V 50 Hz 1/N ~ 240 V 50 Hz 1/N ~ 240 V 50 Hz
mm
mm
mm
450
370
100
450
445
100
450
445
100
450
590
100
450
740
100
450
890
100
450
1040
100
kg
3.3
4
4
5.2
6.3
7.7
8.9
IP24
II
Alpine white
IP24
II
Alpine white
IP24
II
Alpine white
IP24
II
Alpine white
IP24
II
Alpine white
IP24
II
Alpine white
IP24
II
Alpine white
www.stiebel-eltron.com
CNS U | CNS UT | CNS UE | 9
Installation
Specification
CNS 50-300 UT
Electrical data
Connected load
Power supply
Dimensions
Height
Width
Depth
Weights
Weight
Versions
Version
IP rating
Protection class
Colour
CNS 50 UT
231547
CNS 75 UT
231548
CNS 100 UT
231549
CNS 125 UT
231550
CNS 150 UT
231551
CNS 200 UT
231552
CNS 250 UT
231553
CNS 300 UT
231574
kW
0.5
1/N ~ 240 V
50 Hz
0.75
1/N ~ 240 V
50 Hz
1.0
1/N ~ 240 V
50 Hz
1.25
1/N ~ 240 V
50 Hz
1.5
1/N ~ 240 V
50 Hz
2.0
1/N ~ 240 V
50 Hz
2.5
1/N ~ 240 V
50 Hz
3.0
1/N ~ 240 V
50 Hz
mm
mm
mm
450
370
100
450
445
100
450
445
100
450
590
100
450
590
100
450
740
100
450
890
100
450
1040
100
kg
3.3
4
4
5.2
5.2
6.3
7.7
8.9
24 h time switch 24 h time switch 24 h time switch 24 h time switch 24 h time switch 24 h time switch 24 h time switch 24 h time switch
IP24
IP24
IP24
IP24
IP24
IP24
IP24
IP24
II
II
II
II
II
II
II
II
Alpine white
Alpine white
Alpine white
Alpine white
Alpine white
Alpine white
Alpine white
Alpine white
CNS 75-300 UE
Electrical data
Connected load
Power supply
Dimensions
Height
Width
Depth
Weights
Weight
Versions
IP rating
Protection class
Colour
CNS 75 UE
239296
CNS 100 UE
236297
CNS 150 UE
239298
CNS 200 UE
236299
CNS 300 UE
236300
kW
0.75
1/N ~ 240 V
1.0
1/N ~ 240 V
1.5
1/N ~ 240 V
2.0
1/N ~ 240 V
2.8
1/N ~ 240 V
mm
mm
mm
450
445
100
450
445
100
450
590
100
450
740
100
450
1040
100
kg
4
4
5.2
6.3
8.9
IP24
II
Alpine white
IP24
II
Alpine white
IP24
II
Alpine white
IP24
II
Alpine white
IP24
II
Alpine white
10 | CNS U | CNS UT | UEwww.stiebel-eltron.com
GUARANTEE | ENVIRONMENT AND RECYCLING
ENGLISH
Guarantee
The guarantee conditions of our German companies do not
apply to appliances acquired outside of Germany. In countries
where our subsidiaries sell our products a guarantee can only
be issued by those subsidiaries. Such guarantee is only granted if the subsidiary has issued its own terms of guarantee. No
other guarantee will be granted.
We shall not provide any guarantee for appliances acquired in
countries where we have no subsidiary to sell our products.
This will not affect warranties issued by any importers.
Environment and recycling
We would ask you to help protect the environment. After use,
dispose of the various materials in accordance with national
regulations.
www.stiebel-eltron.com
CNS U | CNS UT | CNS UE | 11
Deutschland
STIEBEL ELTRON GmbH & Co. KG
Dr.-Stiebel-Straße 33 | 37603 Holzminden
Tel. 05531 702-0 | Fax 05531 702-480
info@stiebel-eltron.de
www.stiebel-eltron.de
Verkauf
Tel. 05531 702-110 | Fax 05531 702-95108 | info-center@stiebel-eltron.de
Kundendienst
Tel. 05531 702-111 | Fax 05531 702-95890 | kundendienst@stiebel-eltron.de
Ersatzteilverkauf Tel. 05531 702-120 | Fax 05531 702-95335 | ersatzteile@stiebel-eltron.de
Australia
STIEBEL ELTRON Australia Pty. Ltd.
6 Prohasky Street | Port Melbourne VIC 3207
Tel. 03 9645-1833 | Fax 03 9645-4366
info@stiebel.com.au
www.stiebel.com.au
Austria
STIEBEL ELTRON Ges.m.b.H.
Gewerbegebiet Neubau-Nord
Margaritenstraße 4 A | 4063 Hörsching
Tel. 07221 74600-0 | Fax 07221 74600-42
info@stiebel-eltron.at
www.stiebel-eltron.at
Belgium
STIEBEL ELTRON bvba/sprl
't Hofveld 6 - D1 | 1702 Groot-Bijgaarden
Tel. 02 42322-22 | Fax 02 42322-12
info@stiebel-eltron.be
www.stiebel-eltron.be
China
STIEBEL ELTRON (Guangzhou) Electric
Appliance Co., Ltd.
Rm 102, F1, Yingbin-Yihao Mansion, No. 1
Yingbin Road
Panyu District | 511431 Guangzhou
Tel. 020 39162209 | Fax 020 39162203
info@stiebeleltron.cn
www.stiebeleltron.cn
Czech Republic
STIEBEL ELTRON spol. s r.o.
K Hájům 946 | 155 00 Praha 5 - Stodůlky
Tel. 251116-111 | Fax 235512-122
info@stiebel-eltron.cz
www.stiebel-eltron.cz
Finland
STIEBEL ELTRON OY
Kapinakuja 1 | 04600 Mäntsälä
Tel. 020 720-9988
info@stiebel-eltron.fi
www.stiebel-eltron.fi
France
STIEBEL ELTRON SAS
7-9, rue des Selliers
B.P 85107 | 57073 Metz-Cédex 3
Tel. 0387 7438-88 | Fax 0387 7468-26
info@stiebel-eltron.fr
www.stiebel-eltron.fr
Hungary
STIEBEL ELTRON Kft.
Gyár u. 2 | 2040 Budaörs
Tel. 01 250-6055 | Fax 01 368-8097
info@stiebel-eltron.hu
www.stiebel-eltron.hu
Japan
NIHON STIEBEL Co. Ltd.
Kowa Kawasaki Nishiguchi Building 8F
66-2 Horikawa-Cho
Saiwai-Ku | 212-0013 Kawasaki
Tel. 044 540-3200 | Fax 044 540-3210
info@nihonstiebel.co.jp
www.nihonstiebel.co.jp
Netherlands
STIEBEL ELTRON Nederland B.V.
Daviottenweg 36 | 5222 BH 's-Hertogenbosch
Tel. 073 623-0000 | Fax 073 623-1141
info@stiebel-eltron.nl
www.stiebel-eltron.nl
Poland
STIEBEL ELTRON Polska Sp. z O.O.
ul. Działkowa 2 | 02-234 Warszawa
Tel. 022 60920-30 | Fax 022 60920-29
biuro@stiebel-eltron.pl
www.stiebel-eltron.pl
Russia
STIEBEL ELTRON LLC RUSSIA
Urzhumskaya street 4,
building 2 | 129343 Moscow
Tel. 0495 7753889 | Fax 0495 7753887
info@stiebel-eltron.ru
www.stiebel-eltron.ru
Irrtum und technische Änderungen vorbehalten! | Subject to errors and technical changes! | Sous réserve
d‘erreurs et de modifications techniques! | Onder voorbehoud van vergissingen en technische wijzigingen! |
Salvo error o modificación técnica! | Excepto erro ou alteração técnica | Zastrzeżone zmiany techniczne i
ewentualne błędy | Omyly a technické změny jsou vyhrazeny! | A muszaki változtatások és tévedések jogát
fenntartjuk! | Отсутствие ошибок не гарантируется. Возможны технические изменения. | Chyby a
technické zmeny sú vyhradené!
Stand 9147
A 295322-39398-9152
4<AMHCMN=jfdc i>
Slovakia
TATRAMAT - ohrievače vody s.r.o.
Hlavná 1 | 058 01 Poprad
Tel. 052 7127-125 | Fax 052 7127-148
info@stiebel-eltron.sk
www.stiebel-eltron.sk
Switzerland
STIEBEL ELTRON AG
Industrie West
Gass 8 | 5242 Lupfig
Tel. 056 4640-500 | Fax 056 4640-501
info@stiebel-eltron.ch
www.stiebel-eltron.ch
Thailand
STIEBEL ELTRON Asia Ltd.
469 Moo 2 Tambol Klong-Jik
Amphur Bangpa-In | 13160 Ayutthaya
Tel. 035 220088 | Fax 035 221188
info@stiebeleltronasia.com
www.stiebeleltronasia.com
United Kingdom and Ireland
STIEBEL ELTRON UK Ltd.
Unit 12 Stadium Court
Stadium Road | CH62 3RP Bromborough
Tel. 0151 346-2300 | Fax 0151 334-2913
info@stiebel-eltron.co.uk
www.stiebel-eltron.co.uk
United States of America
STIEBEL ELTRON, Inc.
17 West Street | 01088 West Hatfield MA
Tel. 0413 247-3380 | Fax 0413 247-3369
info@stiebel-eltron-usa.com
www.stiebel-eltron-usa.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising