OManual - Geneva2 589016 Rev2 02.08.pub

OManual - Geneva2 589016 Rev2 02.08.pub
WARNING: If the information in these instructions are not followed exactly, a fire or explosion
may result causing property damage and personal injury may result.
- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or
any other appliance.
- WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s
instructions.
• If you cannot reach your gas supplier, call the fire department.
Installation and service must be performed by a qualified installer, service agency or the
gas supplier.
Distributed in New Zealand by
Distributed in Australia by
Glen Dimplex Australasia
38 Harris Road, East Tamaki, Auckland
Phone: 09 274 8265 Fax: 09 274 8472
Email: sales@glendimplex.co.nz
Web: www.masportheating.co.nz
Glen Dimplex Australia Pty Limited
Unit 2, 205 Abbotts Road
Dandenong South, Victoria 3175
Phone: 1 300 566 816 Fax: 03 8787 3570
Email: sales@glendimplex.com.au
Web: masportheating.com.au
Revison 2 February 2008
Part No. 589016
Masport Geneva2
Owners Installation and Operation Manual
Table Of Contents
Description ......................................................................................................Page #
Listing and Codes....................................................................................................................................................3
Copy of certification label ........................................................................................................................................4
Lighting Instructions ................................................................................................................................................5
Specifications ..........................................................................................................................................................6
Warnings, Caution and Safety Notices....................................................................................................................7
Installation Instructions Safety.................................................................................................................................8
Planning Your Installation .........................................................................................................................8
Clearances To Combustibles ....................................................................................................................9
Rear Vent—Snorkel Installation ................................................................................................................9
Top Vent - Venting Diagrams.................................................................................................................10
Horizontal Termination Installation..........................................................................................................11
Vent Restrictor Use And Installation .......................................................................................................12
Vertical Termination Installation ..............................................................................................................12
Basements Installations ..........................................................................................................................12
Through Roof Termination ......................................................................................................................13
Seismic Restraint………………………………………………………………………………………………....14
45° Elbow Offset Information ..................................................................................................................14
Termination Location ..............................................................................................................................15
Gas Supply .............................................................................................................................................16
Aeration Adjustment................................................................................................................................17
Thermostat..............................................................................................................................................18
Logset Installation ...................................................................................................................................18
Wiring Diagrams....................................................................................................................................................19
Operating Instructions Pre Check .........................................................................................................................20
Final Check .............................................................................................................................................21
Shut Down ..............................................................................................................................................21
Fan..........................................................................................................................................................22
Cold Weather Operation........................................................................................................................................22
Glass Cleaning—White Mineral Deposits..............................................................................................................22
Maintenance Gas Valve Replacement ..................................................................................................................23
Viewing Glass Replacement ...................................................................................................................24
Door ........................................................................................................................................................24
Optional Conversion Kits.......................................................................................................................................25
Troubleshooting ....................................................................................................................................................26
Notes / Service History..........................................................................................................................................28
Your Masport gasfire serial number is located on the stove label inside the door on the left hand
side of the stove.
Mail your warranty card TODAY, and SAVE your
RECEIPT. This card is included with the accessory
package inside each firebox.
In order to receive full warranty coverage and to
expedite service, Masport recommends that you
save your receipt and attach it to this page.
By doing this you will have all the necessary
information in the event that your stove may need
warranty service.
Page 2
!
!!
"
!! #
# ! $% &
Masport Geneva2
Owners Installation and Operation Manual
Introduction
Thank you for purchasing a Masport gasfire and welcome to the Masport family. Your new Masport
gasfire will give you many hours of warmth and comfort. Please make sure you take a few minutes to
read this owner’s manual. It explains the steps required to safely assemble, install, operate, and maintain
your new appliance. Proper installation, operation and maintenance will keep your Masport gasfire
burning for years to come.
The Geneva2 is one of the most advanced free standing gas stoves on the market. It is designed using
the latest technology and manufactured to our highest quality standards.
Some of the many features are:
♦
♦
♦
♦!
♦
♦
♦%
♦!
♦
"
#
Geneva2
$
&
Listing & Codes
The Masport gasfire Geneva2 is listed and certified for installation in New Zealand under the following
standards:
- ANSI Z21.88b-2003/CSA 2.33b-2003, Vented Gas Fireplace Heater.
- CAN/CGA-2.17 M-91,
Gas-Fired Appliances for Use at High Altitudes
- NZS5262:2003
- NZS 4553-3.5.1
Please contact Masport if you have any questions regarding the certification of this appliance.
This appliance, when installed must be electrically grounded in accordance with local codes
This appliance is for use only with the type of gas indicated on the rating plate. This appliance is not
convertible for use with other gases, unless a certified kit is used.
Page 3
Masport Geneva2
Owners Installation and Operation Manual
Note: A copy of the certification label is provided here for your review. Due to constant upgrades it is possible that the information shown here may not coincide with the label as attached to the unit. In the event of a discrepancy between the labels, the label on the unit is considered as the correct one.
Page 4
Masport Geneva2
Owners Installation and Operation Manual
Lighting Instructions
Page 5
Masport Geneva2
Owners Installation and Operation Manual
Specifications
2
MODEL Geneva
Natural Gas (NG)
LPG
Manifold Pressure high
0.87 kPa
2.74 kPa
Manifold Pressure low
0.37 kPa
0.87 kPa
Min. Supply Pressure for
Purpose of Input Adjustment
1.2 kPa
3.0 kPa
Max. Supply Pressure for
Purpose of Input Adjustment
3.5 kPa
3.5 kPa
Orifice Size
37# DMS
53# DMS
Nominal Input Rating
29.5 MJ/h
28 MJ/h
Primary Air Opening
3mm (Minimum).
3mm (Minimum).
240 V.A.C. System
240 V.A.C. System
Circulating fan
Variable Speed
Variable Speed
Vent System
100 x 170 mm
100 x 170 mm
Electrical Rating
Geneva2—Stove Dimensions
WIDTH
22” / 559mm
HEIGHT
29.5” / 749mm
DEPTH
18” / 457mm
Page 6
Masport Geneva2
Owners Installation and Operation Manual
Warnings—Caution
IF THIS APPLIANCE IS NOT PROPERLY INSTALLED, A HOUSE FIRE OR EXPLOSION MAY
RESULT. FOR YOUR SAFETY, FOLLOW THE INSTALLATION DIRECTIONS. CONTACT LOCAL
BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION REQUIREMENTS IN
YOUR AREA. PLEASE READ THIS ENTIRE MANUAL BEFORE YOU INSTALL AND USE YOUR
NEW APPLIANCE. FAILURE TO FOLLOW INSTRUCTIONS MAY RESULT IN PROPERTY DAMAGE,
BODILY INJURY OR DEATH.
Safe installation and operation always require common sense.
INSTALLATION AND REPAIR SHOULD BE
DONE BY A QUALIFIED SERVICE PERSON.
THE APPLIANCE SHOULD BE INSPECTED
BEFORE USE AND AT LEAST ANNUALLY BY A
PROFESSIONAL SERVICE PERSON. MORE
FREQUENT CLEANING MAY BE REQUIRED
DUE TO EXCESSIVE LINT FROM CARPETING,
BEDDING MATERIAL, ETC...
THE FLEXIBLE CORD PROVIDED MUST BE
CONNECTED TO A LINE VOLTAGE
ELECTRICAL SUPPLY.
IT IS IMPERATIVE THAT CONTROL
COMPARTMENTS, BURNERS AND
CIRCULATING AIR PASSAGEWAYS OF THE
APPLIANCE ARE KEPT CLEAN.
ANY SAFETY SCREEN OR GUARD REMOVED
FOR SERVICING A ROOM HEATER MUST BE
REPLACED PRIOR TO OPERATING THE
APPLIANCE.
DUE TO HIGH TEMPERATURES, THE
APPLIANCE SHOULD BE LOCATED OUT OF
TRAFFIC AREAS AND AWAY FROM
FURNITURE AND DRAPERIES.
NEVER VENT THE APPLIANCE INTO OTHER
ROOMS OR BUILDINGS. THE APPLIANCE
MUST BE VENTED TO THE OUTSIDE ONLY.
DO NOT USE THIS HEATER IF ANY PART HAS
BEEN UNDER WATER. IMMEDIATELY CALL A
QUALIFIED SERVICE TECHNICIAN TO
INSPECT THE HEATER AND TO REPLACE ANY
PART OF THE CONTROL SYSTEM AND ANY
GAS CONTROL WHICH HAS BEEN UNDER
WATER.
“WARNING” Do not operate appliance with
the glass front removed, cracked or
broken. Replacement of the glass should
be done by a licensed or qualified service
person.
YOUNG CHILDREN SHOULD BE CAREFULLY
SUPERVISED WHEN THEY ARE IN THE SAME
ROOM AS THE APPLIANCE .
CLOTHING OR OTHER FLAMMABLE
MATERIALS SHOULD NOT BE PLACED ON
OR NEAR THE APPLIANCE.
THIS APPLIANCE MUST NOT BE CONNECTED
TO A CHIMNEY FLUE SERVING A SEPARATE
SOLID-FUEL BURNING APPLIANCE.
CHILDREN AND ADULTS SHOULD BE
ALERTED TO THE HAZARDS OF HIGH
SURFACE TEMPERATURES AND SHOULD
STAY AWAY TO AVOID BURNS OR
CLOTHING IGNITION.
Natural gas & LPG gas have odor additives for the
purpose of leak detection through smell. This odor
can fade with time. If the odor is reduced, it is possible to have a dangerous buildup of gas without your
being able to smell it. If you are using any gas appliances in your home the manufacturer recommends
that you have one or more UL approved gas detectors installed in your home. They should be installed by a qualified gas installer for safety purposes.
Page 7
Masport Geneva2
Owners Installation and Operation Manual
Installation Instructions—Safety
GENERAL SAFETY (HOMEOWNER)
•
•
•
VENTING SAFETY
To clean the stove, make sure the appliance
is off and cold. Remove the logs and embers.
The logs must be handled with extreme
care, they are fragile. Use a vacuum to
clean burner and air openings in the bottom
and back of the appliance. Carefully replace
the logs and embers.
Fire Extinguisher: Every home should have at
least one fire extinguisher. An approved
Class A-B-C extinguisher should be mounted
on the wall near an exit and close to the
appliance, but not so close that accessibility
to the extinguisher could be
blocked by a
fire. Your local Fire Department can advise
you concerning the most appropriate location.
Smoke Detectors & Carbon Monoxide
Detectors: Install at least one smoke detector
on each floor of your home to ensure your
safety. It should be located away from the
gas appliance and close to the sleeping
areas. Follow the smoke detector
manufacturers placement installation and
maintenance instructions. Your local Fire
Department may provide assistance in
selecting smoke detectors and CO-detectors.
It is strongly recommended, for your family’s
protection, that a CO-detector be placed in all
homes that utilize gas in any form.
FOR THE INSTALLER
1) Wear gloves and safety glasses for
protection.
2) Exercise extreme caution when using ladders
or when on roof tops.
3) Be aware of electric wiring locations in walls
and ceilings.
4) Use a back support when doing any
heavy lifting.
•
•
•
The appliance vent should be enclosed when
installed in or passing through a living area,
where children may come in contact with it.
Only vent terminations specified may be used
with this stove.
Venting terminals shall not be recessed into a
wall or siding.
PLANNING YOUR INSTALLATION
Please note the following key points
regarding the location of your appliance:
•
•
•
•
•
A sufficient gas pressure is required to supply
the unit with a minimum inlet pressure
Allow adequate accessibility clearances for
servicing and proper operation.
Allow adequate clearance to combustibles.
Consider the termination location.
A suitable power outlet is required to provide
power to the fan.
CLEARANCES TO COMBUSTIBLES
IMPORTANT: All clearances listed are the
MINIMUM required and must be strictly
followed.
This appliance is certified for installation on a
solid combustible surface, such as a wood floor,
vinyl or carpeting.
The following pages provide diagrams for safe
clearances to combustibles.
Ensure, as in any installation, that structural
members are not cut or weakened during
installation .
When installing the appliance in a mobile or
manufactured home, it must be securely
anchored to the floor by means of the anchor
provided in the mobile home kit. Also ensure
that proper grounding is provided by using a
#8 grounding lug, wire and a star washer.
Page 8
Masport Geneva2
Owners Installation and Operation Manual
Installation Instructions
CLEARANCES TO COMBUSTIBLES
A
B
C
MODEL Geneva
Side Wall to unit side
Back wall to unit back
Corner to side wall
VENTING
2
IMPORTANT: This appliance'
s venting system
is room sealed, which means that there should
be no provision to allow room air to be used in
the combustion process.
275mm
100mm
50mm
Note: Only approved venting systems may
be used with the Geneva2.
PLANNING YOUR VENT INSTALLATION
This type of direct vent system may terminate in
one of two ways: Vertical termination using a
vent cap, or Horizontally using a wall termination.
There are limitations to the vertical and/or
horizontal lengths. When calculating the length
of the vent pipe from the outlet of the appliance
to termination, allow for ceiling thickness,
vertical rise in the attic or second story and
sufficient vertical height above the roof.
LOCATING YOUR STOVE
Minimum clearances listed above must be
maintained. Also ensure that you have left
clearance for servicing and that that the proposed
termination location is correct.
Fire stops are required at each floor level the
vent passes through.
When carrying out vertical installations that
require 45° elbows add additional pipe to allow
for the offset.
REAR VENT—SNORKEL TERMINATION
'()('*' +,%#(
- %( ,
./ 0
' 1('*' !2%(3 2)# - %*) 400
5
2 6/ 7
(
400
&
./ 0
./ 0
#
./ 0
/0
*
( &
&
8
400
9:/ 0
'
Page 9
8
Masport Geneva2
Owners Installation and Operation Manual
Page 10
Masport Geneva2
Owners Installation and Operation Manual
Installation Instructions
WARNING: A minimum clearance of 50mm to combustibles must be maintained around
the vent pipe on horizontal pipe runs and 25mm on vertical runs.
(
&
#
8
/ C0;
C0;
) / :C;
8
!
"
5
"
#
Horizontal Wall Vent Terminations
#
$
;/
'
;00
250mm square
.
$
,"
.
$
8
"
40
)2#,< --25() #!, +,)# =(=, #2 -2=, >25) #25 %> #!, +,)#
#,%'() #(2) 2*->
* , =22% 2'?* #(2) )>92% !( !
#,'=,%#*%, #! # ' @ =%, ,)# A(%, ! 3 %> '
:/ 0
"
:/ 0
8
"
(
(
&
;B 0
5
?
"
,
8
Page 11
CL
CL
Center of
hole
Masport Geneva2
Owners Installation and Operation Manual
Installation Instructions
Vertical Installations
?
:/
:/
>2 )2# =
%
$
5
Basement Installations
#
D (% =
, 5(#! () *- #(2)
"
@
6/ 7
./ 0
5
400
? " 95
:/ 0
5
8
8
Minimum 300mm
Drainage
NOTE: ALWAYS CHECK YOUR LOCAL CODES
BEFORE INSTALLING VENTING. NECESSARY
CLEARANCES AND REQUIRMENTS MAY VARY
Restrictor
Restrictor Sizes
Vent Restrictors
>
"
#
$
8
5
=
100mm Collar attached to unit
Page 12
Masport Geneva2
Owners Installation and Operation Manual
Installation Instructions
Through Roof Framing
Termination Above Roof
Maintain 250mm opening relative to the pitch
of the roof.
Consult local codes for minimum vent cap height
above the roof, vent must be a minimum 50mm
from any wall.
250mm square
Use a suitable round or square support
through the roof. Ensure adequate heat
shield protection is provided.
To prevent water seepage install the flashing
with upper portion slid under the roofing material
and the lower portion over the roofing material.
Note: Do not fasten down until the final
adjustments to the vent have been made.
Page 13
Masport Geneva2
Owners Installation and Operation Manual
Installation Instructions
Offset Chart
Typical vent Installation
!
#
+
F 44;
L
Height
A
6/ 7
8
Offset
Offset chart for 45° Elbows
Offset
Pipe Length
(L)
#
G
Height
5
&
6.96
;:;
0
0
;.;96
..E
4
::4
C
;/ :
;E;9:
66/
;;;96
:B C
4
::4
;4;9:
64/
;.;96
..E
;:
.0/
:;.96
//:
:;.96
//:
:6
C;0
.0;96
ECB
.0;96
ECB
.C
4;6
.4
44;
.B
4C/
6B
;:;4
6E
;;46
Seismic Restraint
New Zealand Regulations require that flued gas heaters be secured to prevent shifting in
the event of an earthquake. This is done by fastening the heater to the floor right through
the floor protector if one is fitted. Fasten with two screws not less than 6mm diameter.
Page 14
Masport Geneva2
Owners Installation and Operation Manual
Page 15
Masport Geneva2
Owners Installation and Operation Manual
Installation Instructions (Gas Supply)
Pedestal Cover Removal
#
6
#
8
#
5
5
#
6
, 3 4 / ( * $ , $ 3 & ( $ ( 5 + , 1 , * 2 1 &+ . - ! $ / &/ & - 6 ! 4 6 ! 2 ( + . ( ( ( $ $ ! * 4 - ! $ ,
( + &,
+ , + . &$ ! / / 3 &!
( 4, ) ! * ( , 1 * (! 5 4 +, . , , 2 ) / +. ( - ! $ $) //34 ' ( $) * ( - ! $ /3)6 ' & & $ + * ) + &, $ ! 5 ! 3 3 $ + ! + ( 7/ * , 8 & &! 3 ! 5 3 , ! 3 , 5 ( $ ! * ( ! * ( ) 3 3 4 , 3 3 , 1 ( 5 ) $ (
! / / * , 8 ( 5 3 ( 9 &' 3 ( - ! $ ,
( + &, $ , * * &- &5 / &/ & - 5 ( / ( 5 & - , / * , 8 & &! 3 ! 5 3 , ! 3
, 5 ( $ + , ! + + ! . ' ) * ( * + , - ! $ $ ) / / 3 4 ' ( $ ) * ( + , ) $ ( / * , / ( * $ &: ( - ! $ $ ) / / 3 4 3 & (
! * ( ) 334 . ( 2 ! 33 ,
( + &, $ , * - ! $ 3 ( ! 2 $ 1 &+ . $ , ! / ! 5 1 ! + ( * $ , 3 ) + &,
( ! . & $ + ! 3 3 ! + &, 6 ) $ + ,
, * 6 + , ! 3 3 3 , ! 3 $ + ! + ( 7/ * , 8 & &! 3 ! 5 ! + &, ! 3 , 5 ( $
* ( ( * + , + . ( ! + &, ! 3 ) ( 3 - ! $ , 5 ( 3 , ! 3 : , & - ! 5 , 5 ( ! ) + . , * &+ &( $ , * 5 ( + ! &3 $ ,
& $ + ! 3 3 ! + &, * ( ; ) &* ( 6 ( + $
EXISTING GAS SUPPLY
?
♦
♦
"
"
?
#
H
♦
♦
$
GAS SUPPLY INSTALLATION
=
!
$
8
8
#
#
5
"
./
&
=
&
5
8
./
&
H
=
A
$
%
&
#
&
; :6 =
"
./
=
. 00 =
-=
' "
-=
' ( $ ) * ( + , + &- . + ( + . ( / * ( $ $ ) * ( + ! / $ ( + 0$ * ( 1 ! + ( *
- !$ ,
( + &, $ , * - ! $ 3 ( ! 2 $
Page 16
. ( 2 & - +. ( /* ($$) * (
. ( 2 ! 33
Masport Geneva2
Owners Installation and Operation Manual
Installation Instructions
PIPING DETAIL
AERATION ADJUSTMENT
♦
♦
&6 / , * + ! +
#
""
#
"
A
=
, +
9
8
"
#
;9:I #
9
♦
♦
!
)3
/ :C;
&
CAUTION: Parts requiring adjustment
during operation may be hot.
! #
• %
• -
<
%
=>
8
•
#
• #
• %
)
%
<
FACTORY SETTING
Natural Gas
3.0 mm Open
LP GAS
3.0 mm Open
Flame Picture
Open -Soft blue flame
Closed - tall yellow flame
- ! $ $) //34 /* ($$) * (
)
'
; :6
' "
./0
-=
'
. 00
' "
./0
IMPORTANT: Always check for gas leaks with soap and water solution or gas leak detector.
Do not use open flame for leak detection.
Page 17
Masport Geneva2
Owners Installation and Operation Manual
Installation Instructions
THERMOSTAT
LOGSET INSTALLATION
WARNING: The gas valve of this appliance
operates on a millivolt system and is not
intended to be connected to any other
power source.
(
8
! ) + &,
*-
""
""
1 !* & -
5
+
6 )$+
"
"
'
:/ 0&E/ 0
,
""
&
"
*-
"
&
#
-
(
'
Geneva2
Back Log
OPTIONAL REMOTE
A
Front Log
(
"
%
'
See wiring diagrams for details on valve
connections.
&
; =
,
Note: When installing a remote control or
wall switch use the correct gauge of wire.
See table below.
Wire Size
Max. Length
2.0mm
15m
1.6mm
10m
1.0mm
6m
0.9mm
4m
0.7mm
3m
Front Log
Pins
: -
WARNING
Electrical Grounding Instructions
This appliance is equipped with a three prong (grounding)
plug for your protection against shock hazard and should be
plugged directly into a properly grounded three prong
receptacle . Do not cut or remove the grounding prong from this
plug.
Page 18
Masport Geneva2
Owners Installation and Operation Manual
Wiring Diagrams
,
"
3
"
1
Blower Control
240 VOLT CIRCUIT
Snap Disc
Chordset
Ground
MILLIVOLT CIRCUIT
Circulation Fan
Pilot Assembly
Thermocouple
Thermostat
On/Off Rocker
Switch
Thermopile
Thermostat leads or leads to
optional remote thermostat
TH
Pilot Gas Line
TP
Honeywell Gas Valve
Page 19
THTP
Masport Geneva2
Owners Installation and Operation Manual
Operating Instructions
Pre– Start Up Checks
FOR YOUR SAFETY READ - BEFORE LIGHTING
WARNING
IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR
EXPLOSION MAY RESULT CAUSING PROPERTY AND/OR PERSONAL INJURY
DO NOT: Use tools to operate controls, only use your hand to push in and turn the controls.
DO NOT: Try to repair the appliance. Call a qualified service technician.
DO NOT: Use this appliance if any part has been under water. Immediately call a qualified
service technician to inspect the appliance and replace any part of the gas control
sys tem which has been under water.
DO NOT: Use this appliance if you smell gas.
WHAT TO DO IF YOU SMELL GAS:
♦
OPEN WINDOWS.
♦
DO NOT TOUCH ANY ELECTRICAL SWITCH; DO NOT USE THE PHONE IN YOUR
BUILDING.
♦
EXTINGUISH ANY OPEN FLAME.
♦
IMMEDIATELY CALL YOUR GAS SUPPLIER FROM A NEIGHBOR’S PHONE AND
FOLLOW THE GAS SUPPLIER’S INSTRUCTIONS.
♦
IF YOU CANNOT REACH YOUR GAS SUPPLIER, CALL THE FIRE DEPARTMENT.
WARNING—Do not operate appliance with the viewing glass
removed, cracked or broken. Viewing glass must be replaced /
repaired by MASPORT . For replacement please contact your local
dealer or Masport to make arrangements to have your viewing glass
replaced / repaired. Glass breakage due to slamming the viewing
door or abusing your unit, is not covered under warranty.
Page 20
Masport Geneva2
Owners Installation and Operation Manual
Operating Instructions
FINAL CHECK
& $+! 33(* '
♦
♦
♦
♦
♦
♦
♦
♦
♦
♦
♦
♦
♦
♦
""
' +)
"
+
! #
"
""
@
"
?
<
<
"
""
>
?A>
"
NOTE: When first fired, the unit will produce an odor. This is normal and is part of the paint
curing process, it may be noticeable for at least 4 hours. It is recommended that you open a
few windows to ventilate the room. During the first hour smoke detectors in the house may
be set off.
Following the initial burn-in period, the glass panel may require cleaning.
CAUTION: Do not clean the glass when the appliance is hot!
When the appliance is cold, firing may cause the glass to fog up. This is due to condensation
and is normal.
Make yourself familiar with these instruction before operating the appliance.
Check any loose electrical wires that may cause a shock.
Check around the appliance for gas leaks. IF YOU SMELL GAS, follow the instructions on
the front cover of this manual.
Check to see that logs are correctly positioned. The pilot light should be visible.
Check to make sure that venting is secure.
Check all external parts, such as grills, doors and control cover are properly attached and
fastened.
CAUTION: Do not turn the unit off and on again without a minimum of a 60 second
wait between firing.
Make sure you read this entire manual, especially the lighting instructions on page 5,
before you begin stove operation.
Keep in mind that your thermostat will only work to control your stove if the
ON/OFF rocker switch is set to the “OFF” position. The “ON” position will
prevent the thermostat from controlling the stove. When you are lighting your
pilot your thermostat should be set to the lowest level and the ON/OFF rocker
switch should be set to “OFF”.
ON/OFF
rocker switch
TEMPORARY SHUT-DOWN
To turn off the main burner only, set the thermostat to the lowest setting or turn remote switch to OFF.
Press and turn the knob clockwise
to PILOT position.
COMPLETE SHUT-DOWN Press and turn the knob clockwise
to the OFF position.
CONTROL KNOB POSITIONS
Honeywell
Unit Off
Robertshaw
Honeywell
Burner On
Page 21
Robertshaw
Honeywell
Pilot
Robertshaw
Masport Geneva2
Owners Installation and Operation Manual
Operating Instructions
FAN OPERATION
The convection fan speed control is located on the back of the unit. Turning the control
knob all the way counterclockwise will turn off the convection fan. Adjust the blower to
the desired speed.
NOTE: The fan will turn on once the unit has reached operating temperature. This
prevents the discharge of cold air.
♦
NORMAL OPERATING SOUNDS
FIREBOX: You may hear some cracking or ticking sounds on start-up and shut-down.
This is due to the expansion and contraction of the steel in the firebox.
♦ BLOWER: We use high efficiency fans in our appliances. You may hear a whirring
sound when the fan turns on. This will decrease or increase depending on the speed
setting of the fan.
♦ PILOT FLAME: You may detect a very slight whisper sound from the pilot when it is
turned on.
♦ These are all normal sounds associated with this type of appliance and should not
be considered as defects.
♦
IMPORTANT - GLASS CLEANING - WHITE MINERAL DEPOSITS
2
#
@
(
5
>
#
(
"
"
;
(
:
(
),+,%
.
*
6
2
>
'
5
?%
2
22D #2= -, ) %,',
, +(
"
=2-( ! =-*
5!(#, 2AA
%
(
"
,- 2
+
"
6
D,- D,'
%*#- )>
NOTICE: COLD WEATHER OPERATION
5
"
-=
) #
*
"
$
#
"
5
#
"
,"
(
"
&
! ) + &,
1 . ( , / ( * ! + & - 4 , ) * ! / / 3 &!
! / , * ( 9 ( $ $ &8 ( & ( ' ) &3 5 ) /
(
( 5)*& -
, 35 1 (! +. (* 4, ) 6 ) $+
J=
K
Page 22
* (; ) ( +34
. ( 2 +. ( (9. ! ) $+
Masport Geneva2
Owners Installation and Operation Manual
Maintenance
CAUTION: NEVER CLEAN THE APPLIANCE WHEN IT IS HOT. ANY SAFETY SCREEN OR
GUARD REMOVED FOR SERVICING MUST BE REPLACED PRIOR TO OPERATING THE
APPLIANCE. DO NOT USE ANY SUBSTITUE MATERIALS.
FREQUENCY OF SERVICE
TECHNICAL INSTRUCTIONS
Regularly:
♦
♦
♦
D
8
♦
+
♦
Thermopile
♦
Thermocouple
Pilot for
Burner ignition
Once a Year:
♦
PILOT ASSEMBLY: The correct flame pattern
should have three strong blue flames. One flows
around the thermopile, one around the thermocouple and one flows over the burner. See page 26 for
further pilot instructions
2
&
&
♦
#
+
Have a qualified service technician:
♦
♦
♦ LOGS:
1. Check logs are correctly positioned (see installation
instructions).
2. Check there are no cracked logs.
3. Clean off any soot deposits using a soft brush.
NOTE: Incorrect log positioning may cause carbon
build up and discoloration. This may void the
warranty.
"
♦
Pedestal Cover Removal
#
#
6
#
8
5
5
#
♦ VENTING:
1. Check the venting system for any signs of
corrosion.
2. Remove the vent termination and check the inside
of the vent by shining a light down the pipe.
3. Inspect pipe seams and joints and ensure they are
still tight.
4. Check wall straps and all vent supports.
6
REMOVING THE BURNER ORIFICE
1. Use a 1/2” wrench to loosen and remove the burner
orifice.
2. Change the orifice.
GAS VALVE REPLACEMENT:
1. Disconnect electricity to the appliance.
2. Shut off the gas to the appliance and disconnect the
gas line to the appliance.
3. If the appliance has a remote switch or thermostat,
disconnect the wires at the front of the valve.
4. Undo the four screws holding the valve plate to the
pedestal assembly.
5. Gently rotate the valve to gain access to the
millivolt wiring, pilot tube nut and burner supply tube
nut.
6. Carefully undo the pilot and burner supply tubes
and remove the valve.
7. Replacing the assembly is the reverse of the above
instructions.
Page 23
Masport Geneva2
GOLD PLATING:
Owners Installation and Operation Manual
Maintenance
1. Gold plating requires little maintenance and needs only to be cleaned with a soft damp cloth. Do not use any
abrasive cleaning materials.
2. Avoid fingerprints on gold. Wipe off fingerprints before firing.
DOOR :
Check the gasket to see that it is still forming a seal. Replace gasket if there is any sign of wear.
VIEWING GLASS REPLACEMENT:
This appliance is supplied with high temperature 5mm high temperature ceramic glass that will easily withstand the
heat your unit was designed to produce. In the event the glass breaks, contact your dealer or MASPORT to arrange
for your glass to be replaced / repaired.
REMOVING THE BLOWER:
1.
2.
3.
4.
5.
Turn the gas off to the unit.
Turn off/unplug the electric supply.
Remove the back panel on the pedestal.
Remove the 4 screws on the back panel that attach the blower.
Replacing the assembly is the reverse of the above instructions
Page 24
Masport Geneva2
Owners Installation and Operation Manual
Optional Conversion Kits
“ This conversion kit shall be installed by a qualified service agency in accordance with the
manufacturer’s instructions and all applicable codes and requirements of the authorities having
jurisdiction. If the information in these instructions is not followed exactly, a fire, explosion or
production of carbon monoxide may result causing property damage, personal injury or loss of life. The
qualified service agency is responsible for the proper installation of the kit. The installation is not
complete until the operation of the converted appliance is checked as specified in the instruction manual
supplied with the kit.” Before performing this or any service procedure, make sure that the gas supply to
the unit and the electrical supply are shut off.
CONVERSION KIT CONTENTS
1. Main Burner orifice.
2. Valve Kit.
3. Conversion Sticker
The model Geneva2 is designed to burn either Natural
Gas or LPG Fuel. Each heater leaves the factory
equipped for one specific fuel but it is a simple operation to convert the heater to an alternate fuel in the
field. The original fuel type is marked on the rating
label:
To convert to an alternate fuel, follow these steps:
1. Open the front viewing door.
NATURAL GAS
2. Remove the log set and brick panels.
3. Remove the log support plate screws.
4. Remove the burner assembly.
6. Remove the pedestal wrap
7. Using a 1/2” socket, unscrew the main burner orifice and replace with
alternate gas orifice. Note That the primary air bracket can be rotated to
removed orifice
8. See the separate gas valve manufacturers instructions supplied in the kit.
9. Replace in reverse.
To Convert the Pilot fuel, follow these steps:
1. Use a 7/16” wrench to loosen the pilot hood
2. Push the little silver tab in and the little red tab should pop out.
3. The red tab out is used for LPG
4. The silver tab out is for Natural Gas
5. Re-tighten the pilot hood.
LPG
Pilot Hood
Fuel Type Tab
See page 27 for pilot
instructions.
LEAK TESTING:
CAUTION: DO NOT TEST FOR LEAKS WITH AN OPEN FLAME.
♦ With the main burner “ON”, test the new pressure regulator using a soap solution
♦ Check all fittings for leaks using the soap solution.
FUEL CONVERSION LABEL:
Fill out and attach the fuel conversion label #0630 provided in the kit and attach it to the stove near the upper
right hand corner of the approval label inside the left hand side door of the unit.
♦
AERATION ADJUSTMENT
IMPORTANT: IF YOU CHANGED THE FUEL THE AERATION WILL REQUIRE
ADJUSTMENT - SEE PAGE 18
ALLOW THE UNIT TO BURN FOR AT LEAST 15 MINUTES TO CHECK THE FLAME PICTURE.
If you have converted from Natural gas to LPG you will have to INCREASE the aeration opening as LPG
requires more primary air to burn correctly.
♦ If you have changed from LPG to Natural gas you may have to REDUCE the aeration opening as Natural gas
requires less primary air to burn correctly.
♦
Page 25
Masport Geneva2
Owners Installation and Operation Manual
Troubleshooting
=
1 !* & - #
! ) + &,
"
8
-
5
/*, '3(6
/ , $ $ &' 3 (
+
!)$(
=
, * * ( + &8 ( ! + &,
•
=
8
•
•
(
<
•
•
$
•
9
•
•
•
=
5
) <(
(
•
(
$
!
" #
(
#
•
.0
•
•
#
$
(
L,
•
H
:/ 0
•
•
=
+ . 0+ . + /
7
$
A 8
%
•
&
8
•
'
(
•
•
•
#
(
•
,"
&
•
•
&
•
%
•
•
#
@
•
&
H
!
•
(
•
•
? &
5
&
Page 26
:60+
(
:60+
Masport Geneva2
Owners Installation and Operation Manual
2)+,% (2) () #%* #(2) A2% 2)+,%#(?-,
2%(A( , () ,)> '2*)# ?% D,# =(-2# O O ,%(,
)2#,<(# ( )2# ), ,
%@ #2 %,'2+, #!, =(-2# #*?, A2%
; -22 ,)
5 %2# #(2)
#!, =(-2# # % ,# !,1
A(##() ;96 #*%) 5(#!
E9;CO ,)> 5%,) !
!25)
() A( *%, * , *#(2)
#2 +2(> ?,)>() 2%(A( ,
#%(= ?@ ('=%2=,%
=- ,',)# 2A ,)> 5%,) !
2)+,% (2)
A( *%,
+2(> 2)# #()
2%(A( , #%(=
5(#! ,)> 5%,) !
A (-*%, #2 >2
#!(
) * ,
>( #2%#(2) 2A #!,
2%(A( , #%(=
5!,) -22 ,)()
2% #( !#,)()
: =* ! 2%(A( , #%(= # ?
-- #!, 5 @
() # #!,
!,1 A(##()
!25) ()
A( *%, ?; N ?:
)2#,<2%(A( , #%(= ' @ ?, % )>2'-@ -2
#,> 2) )@ (>, 2A !,1 A(##()
+(,5() >25) 2) =(-2#
M0 ;:0
) #*% =2 (#(2) &
)2 M;9;C !2-, +( (?-,
-=
=2 (#(2) &
M;9;C !2-, N %,>
2-2% 2>, +( (?-,
) #
-=
A( *%, ?:
A#,%
A( *%, ?;
?,A2%,
A( *%,
. %,&#( !#,) #!, =(-2#
# % ,# !,1 A(##() *)#(#!, =(-2# # % ,# -( )
5(#! #!, #!,%'2 2*=-, N
#!,%'2=(-,
!25) ()
A( *%, * , *#(2) #2
+2(> ?,)>() 2%(A( ,
#%(= ?@ ('=%2=,% =- ,&
',)# 2A ,)> 5%,) !
+2(> 2)# #()
2%(A( , #%(=
5(#! ,)> 5%,) !
A (-*%, #2 >2
#!(
) * ,
>( #2%#(2) 2A #!,
2%(A( , #%(=
5!,) -22 ,)()
2% #( !#,)()
6 () # -- #(2) (
2'=-,#,
Page 27
Masport Geneva2
Owners Installation and Operation Manual
NOTES
SERVICE HISTORY
DATE
CORRECTIVE ACTION (INCLUDE REPLACEMENT PARTS)
Distributed in New Zealand by
Distributed in Australia by
Glen Dimplex Australasia
38 Harris Road, East Tamaki, Auckland
PO Box 58 473, Greenmount, Auckland
Phone: 09 274 8265 Fax: 09 274 8472
Email: sales@glendimplex.co.nz
Web: www.masportheating.co.nz
Glen Dimplex Australia Pty Limited
Unit 2, 205 Abbotts Road
Dandenong South, Victoria 3175
Phone: 1 300 566 816 Fax: 03 8787 3570
Email: sales@glendimplex.com.au
Web: masportheating.com.au
Customer Hotline 0800 655 001
Manufactured in Canada by:
Valley Comfort Systems Inc.
1290 Commercial Way
Penticton, BC V2A 3H5
Ph# 1-250-493-7444
Email sales@blazeking.com
Page 28
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising