HP ProLiant WS460c Generation 6 (G6) Workstation Blade

HP ProLiant WS460c Generation 6 (G6) Workstation Blade
QuickSpecs
HP ProLiant WS460c Generation 6 (G6)
Workstation Blade
Overview
1.
2.
3.
4.
HP ProLiant WS460c G6 Workstation Blade
Two (2) mezzanine I/O expansion slots
5. Two (2) small form factor (SFF) hot-plug drive bays
Internal USB connector
6. Local I/O Connector
Twelve (12) DDR3 Registered or Un-buffered DIMM
7. Internal SD card slot
Memory Slots
8. Up to two (2) Intel® Xeon® 5500 or 5600 series
processors
HP Smart Array P410i Controller
9. Access Panel
DA - 13429 Worldwide QuickSpecs — Version 27 — 8.31.2012
Page 1
QuickSpecs
HP ProLiant WS460c Generation 6 (G6)
Workstation Blade
Overview
HP ProLiant WS460c G6 Workstation Blade with HP WS460c G6 Graphics Expansion Blade
1. HP Graphics Expansion Blade
4. Small form factor (SFF) drive bays
2. Standard full length PCI Express Generation 2 (x8) slot 5. HP ProLiant xw460c Blade Workstation base system
2; (shown vacant)
3. Standard full-length PCI Express Generation 2 (x8); slot 6. Local I/O Connector
1 (shown with graphics card)
What's New
Support for Multi-GPU Pass-through with Citrix XenServer 6 Enterprise or Platinum Edition
Support for HP SAS 6G Enterprise Hard Drive
At A Glance
This document covers the HP ProLiant WS460c G6 workstation blade and its specific options. For more information on
HP BladeSystem c-Class Enclosures and HP BladeSystem c-Class Interconnect and Mezzanine Components, please
see the following:
HP BladeSystem c-Class Enclosures QuickSpecs:
HP BladeSystem c3000 Enclosure QuickSpecs:
http://h18000.www1.hp.com/products/quickspecs/12790_div/12790_div.html
HP BladeSystem c7000 Enclosure QuickSpecs:
http://h18000.www1.hp.com/products/quickspecs/12810_div/12810_div.html
HP BladeSystem c-Class Interconnect and Mezzanine Components:
DA - 13429 Worldwide QuickSpecs — Version 27 — 8.31.2012
Page 2
QuickSpecs
HP ProLiant WS460c Generation 6 (G6)
Workstation Blade
Overview
http://h18004.www1.hp.com/products/blades/components/c-class-interconnects.html
http://h18004.www1.hp.com/products/blades/components/c-class-adapters.html
The HP ProLiant WS460c G6 provides greater 2P x86 server blade density without compromise and maximum powerefficiency with flexibility and choice.
HP ProLiant WS460c G6 workstation blade and optional HP WS460c G6 graphics expansion blade includes:
Processor:
Up to two (2) Intel® Xeon® 5500 or 5600 Series processors
Intel® 5500 Chipset
Memory:
Twelve (12) DIMM slots
Up to 192GB, using PC3-8500 DDR3 Registered (RDIMM) memory, operating at 800MHz when fully
populated at 2 DIMMs per Channel in 12 slots
Up to 48GB, using PC3-10600 DDR3 Unbuffered (UDIMM) memory, operating at 1333MHz when fully
populated at 2 DIMMs per Channel in 12 slots
Storage Controller:
HP Smart Array P410i Controller (RAID 0/1) with optional 256MB or 512MB Battery-Backed Write Cache
(BBWC)
Internal Drive Support:
Up to two (2) small form factor (SFF) SAS hot plug hard disk drives
Network Controller:
Embedded NC532i Dual Port Flex-10 10GbE Multifunction Server Adapter
One (1) additional 10/100 server adapter dedicated to iLO 2 Management
Mezzanine Support:
Two (2) I/O expansion or graphics adapter mezzanine slots
Supports up to (2) mezzanine cards
Graphics adapter mezzanine (NVIDIA Quadro FX880M or FX2800M)
4GB Dual-Port Fibre Channel Mezzanine options for SAN connectivity (Choice of Emulex or QLogic)
Now supporting the configuration to simultaneously run a mezzanine option card in Workstation Blade
and a PCI express single slot graphics card in the Graphics Expansion Blade.
4X QDR (40Gbps) and DDR (20Gbps) InfiniBand (IB) Mezzanine options for low latency and high
bandwidth server interconnectivity. All QDR option support is supported on Red Hat Linux Operating
System only.
Graphics Adapter:
Professional 2D & 3D graphics with hardware acceleration via graphics subsystem
NVIDIA Quadro FX 880M with 1G (Single or dual cards configuration capable)
For professional 2D & 3D graphics with hardware acceleration via graphics subsytem
1G (DDR3) memory
Supports up to two displays
Mezzanine card can occupy either mezzanine slot 1 or 2
GPU Pass-through not supported on this device
NVIDIA Quadro FX 2800M (Single card configuration only)
For professional mid-range graphics application
1G (GDDR3) memory
Supports up to two displays
Mezzanine card which occupies mezzanine slot 2
GPU Pass-through not supported on this device
NVIDIA Quadro 4000 (Single wide PCIe-x16 in graphics expansion blade)
For professional mid-range graphics and stereoscopic 3D, scalable visualization and 3D highdefinition broadcasting
2GB (GDDR5) memory
Supports up to two displays
PCe-x16 full height card (Two per Graphics Expansion Blade)
GPU Pass-through with
NVIDIA driver 261.xx or greater
DA - 13429 Worldwide QuickSpecs — Version 27 — 8.31.2012
Page 3
QuickSpecs
HP ProLiant WS460c Generation 6 (G6)
Workstation Blade
Overview
Citrix XenDesktop 5.5 Enterprise/Platnium, XenServer 6 Enterprise / Platinum editions
NVIDIA Quadro 5000 (Double Wide PCIe-x16 in graphics expansion blade)
For high-end 3D graphics, M&E animation and CAD applications
2.5G (GDDR5) memory
Supports up to two displays
PCe-x16 full height card (one per Graphics Expansion Blade)
GPU Pass-through with
NVIDIA driver 261.xx or greater
Citrix XenDesktop 5.5 Enterprise/Platnium, XenServer 6 Enterprise / Platinum editions
NVIDIA Quadro 6000 (Double Wide PCIe-x16 in graphics expansion blade)
For ultra high-end 3D graphics, M&E animation and specialized healthcare and oil&gas applications
6GB (GDDR5) memory
Supports up to two displays
PCe-x16 full height card (one per Graphics Expansion Blade)
GPU Pass-through with
NVIDIA driver 261.xx or greater
Citrix XenDesktop 5.5 Enterprise/Platnium, XenServer 6 Enterprise / Platinum editions
AMD Firestream FS9350 Compute Accelerator (Single wide PCIe-x16 in graphics expansion blade)
General Purpose GPU for high-performance computing and large data center, scale-out deployments
2GB (GDDR5) memory
Supports up to two displays
PCe-x16 full height card (two per Graphics Expansion Blade)
GPU Pass-through not supported on this device
NVIDIA Tesla M2070Q (Double wide PCIe-x16 in graphics expansion blade)
General Purpose GPU for high performance computing, advanced and remote visualization in a
datacenter.
6GB (GDDR5) memory
Supports up to two displays
PCe-x16 full height card (one per Graphics Expansion Blade)
GPU Pass-through not supported on this device.
Single, unified driver compatible with FX 880M, FX 2800M, Quadro 4000, Quadro 5000, Quadro 6000 and
Tesla M2070Q.
Now supporting configuration to simultaneously run a mezzanine option card in Workstation Blade and a
PCI express single slot graphics card in the Graphics Expansion Blade.
Workstation Blade Graphics Software Environment (when combined with HP t610 Thin Client and HP
Remote Graphics Software as access client system)
Quad-display capable on remote access client system
Displays may be oriented in landscape or portrait mode. May also be tiled in matrices
Resolution: Max width 7680 pixels (@7680x1200), max height 7680 pixels (@1200x7680)
Ports:
One (1) internal USB 2.0 connector for security key devices and USB drive keys
One (1) internal SD-HC Card slot
Form Factor:
HP ProLiant WS460c G6 and WS460c G6 Graphics Expansion Blade are both half-height server blades
that plugs into the HP BladeSystem c3000 and c7000 enclosures
Infrastructure Management:
Convenient slide-out Systems Insight Display for quick and easy front view server diagnostics, along with
status LEDs, Automatic Server Recovery (ASR), ROM Based Setup Utility (RBSU)
HP Integrated Light-Out 2 (iLO 2) management processor for simplified server setup, health monitoring and
recovery, power and thermal control, and lights-out remote administration
HP Insight Control suites, as product options, deliver essential infrastructure management that can help
save time and money by making it easy to deploy, monitor, control and optimize your IT infrastructure
through a single, simple management console.
NOTE: Insight Control for Linux is not supported in the HP ProLiant WS460c G6 Workstation Blade.
Operating Systems:
Supports following: (Not preinstalled or preloaded)
Server Operating System:
Microsoft® Windows Server 2008 R2 SP1 (64-bit) Standard, Enterprise and DataCenter
DA - 13429 Worldwide QuickSpecs — Version 27 — 8.31.2012
Page 4
QuickSpecs
HP ProLiant WS460c Generation 6 (G6)
Workstation Blade
Overview
editions
Citrix XenServer 6 Enterprise and Platinum editions
Client Operating Systems:
Genuine Microsoft® Windows 7.0® Business and Enterprise (32-bit and 64-bit)
Genuine Microsoft® Windows Vista® Business (32-bit and 64-bit)
Genuine Microsoft® Windows® XP Professional 32-bit SP3
Genuine Microsoft® Windows® XP Professional x64 Edition with SP2
RedHat Enterprise Linux version 4.8 or 5.3 (64-bit)
Enclosures:
HP offers two different c-Class workstation blade enclosures to meet your individual needs:
The HP BladeSystem c7000 rack enclosure is 10U high and holds up to sixteen (16) ProLiant
WS460c G6 workstations plugged vertically or (8) HP ProLiant WS460c G6 Workstation Blades
paired with (8) HP WS460c G6 Graphics Expansion Blades plugged vertically.
The HP BladeSystem c3000 rack enclosure is 6U high and holds up to eight (8) HP ProLiant WS460c
G6 workstations plugged horizontally or (4) HP ProLiant WS460c G6 Workstation Blades paired with
(4) HP WS460c G6 Graphics Expansion Blades plugged horizontally.
Workstation blades, server blades, storage blades, interconnect modules, power supplies, fans, and
redundant Onboard Administrator modules are all designed to fit into the c3000 and c7000 enclosures.
For additional enclosure information, please see:
http://h18004.www1.hp.com/products/blades/components/enclosures/c-class/index.html.
HP Workstation Blade Solution:
The HP ProLiant WS460c G6 Workstation Blade and the HP WS460c G6 Graphics Expansion Blade are
two components of the several key components for the HP Workstation Blade Solution. For additional
information, please see:
http://h20338.www2.hp.com/enterprise/cache/437050-0-0-225-121.html
Warranty:
This product is covered by a global limited warranty and supported by HP Services and a worldwide network
of HP Authorized Channel Partners. Hardware diagnostic support and repair is available for three years
from date of purchase. Support for software and initial setup is available for 90 days from date of purchase.
Enhancements to warranty services are available through HP Care Pack services or customized service
agreements. Certain restrictions and exclusions apply. Hard drives have either a one year or three year
warranty; refer to the specific hard drive QuickSpecs for details.
NOTE: Server/Workstation warranty includes 3 year Parts, 3 year Labor, 3-year on-site support. Warranty
repairs may be accomplished through the use of Customer Self Repair (CSR) parts. These parts fall into
two categories: 1) Mandatory CSR parts are designed for easy replacement. A travel and labor charge will
result when customers decline to replace a Mandatory CSR part; 2) Optional CSR parts are also designed
for easy replacement but may involve added complexity. Customers may choose to have HP replace
Optional CSR parts at no charge. Additional information regarding worldwide limited warranty and technical
support is available at: http://h18004.www1.hp.com/products/servers/platforms/warranty/index.html
DA - 13429 Worldwide QuickSpecs — Version 27 — 8.31.2012
Page 5
QuickSpecs
HP ProLiant WS460c Generation 6 (G6)
Workstation Blade
Standard Features
NOTE: For the Standard Features shipped in the "Factory Integrated Models", please see the "Configuration Information
- Factory Integrated Models" section.
Processor
Six-Core Processors
One of the following
Intel® Xeon® X5675 (3.06GHz/6-core/12MB/95W, DDR3-1333, HT, Turbo 2/2/2/2/3/3)
depending on Model
Processor
Intel® Xeon® E5649 (2.53GHz/6-core/12MB/80W, DDR3-1333, HT, Turbo 1/1/1/1/2/2)
Processor
Intel® Xeon® E5645 (2.40GHz/6-core/12MB/80W, DDR3-1333, HT, Turbo 1/1/1/1/2/2)
Processor
Quad-Core Processors
Intel® Xeon® E5630 (2.53GHz/4-core/12MB/80W, DDR3-1066, HT, Turbo 1/1/2/2) Processor
Intel® Xeon® E5620 (2.40GHz/4-core/12MB/80W, DDR3-1066, HT, Turbo 1/1/2/2) Processor
Intel® Xeon® X5560 (2.80GHz/4-core/8MB/95W, DDR3-1333, HT, Turbo 2/2/3/3) Processor
Intel® Xeon® E5520 (2.26GHz/4-core/8MB/80W, DDR3-1066, HT, Turbo 1/1/2/2) Processor
Dual-Core Processors
Intel® Xeon® E5502 (1.86GHz/2-core/4MB/80W, DDR3-800) Processor
NOTE: HT indicates that the processor model supports Intel® Hyper-Threading Technology.
NOTE: Turbo indicates the maximum potential frequency increment when using Intel® Turbo
Boost Technology, with 4, 3, 2, and 1 cores active.
NOTE: DDR3 speed is the maximum memory speed of the processor. Actual memory speed
may depend on the quantity and type of DIMMs installed.
NOTE: For the Intel 5500 and 5600 Series, the letter preceding the model number indicates
the performance/wattage of the processor. "X" denotes High Performance/Wattage; "E"
denotes Enterprise Performance/Wattage (Mainstream); and "L" denotes Lower Wattage.
Upgradeability
Upgradeable to two (2) processors
Cache Memory
One of the following
depending on Model
4MB shared L3 cache
8MB shared L3 cache
12MB shared L3 cache
Chipset
Intel® 5500 Chipset
DA - 13429 Worldwide QuickSpecs — Version 27 — 8.31.2012
Page 6
QuickSpecs
HP ProLiant WS460c Generation 6 (G6)
Workstation Blade
Standard Features
Memory
Type
Standard
DDR3 Registered (RDIMM) or Unbuffered (UDIMM)
2GB (2 x 1GB) UDIMM
4GB (4 x 1GB) UDIMM
Maximum (RDIMM)
192GB (12 x 16 GB) for Registered Memory configurations
Maximum (UDIMM)
48 GB (12 x 4 GB) for Unbuffered Memory configurations
NOTE: Depending on the memory configuration and processor model the memory speed may
run at 1333MHz, 1066MHz or 800MHz. Please see the Online Memory Configuration Tool for
details: www.hp.com/go/ddr3memory-configurator
DDR3 memory options part number decoder
Network Controller
Embedded NC532i Dual Port Flex-10 10GbE Multifunction Server Adapter
One (1) additional 10/100 NIC dedicated to iLO 2 Management
I/O Expansion Slots
Two (2) I/O expansion mezzanine slots (x8 PCI Express) Gen 2
Graphics Adapter
(mezzanine card)
One of the following
depending on Model
NVIDIA Quadro FX 880M graphics Generation 2 (via graphics mezzanine card)
NOTE: Workstation class performance for professional 2D graphics, entry/mid 3D graphics.
Supported on HP WS460c G6 only. Not compatible and supported with HP ProLiant BL server
blades.
Memory size/type
1GB / DDR3
Cuda Cores
48
Number of displays
Up to two display per FX 880M 1GB card. May be configured with two
cards.
Graphics driver
Single, unified driver compatible with FX 880M, FX 2800M, Quadro
4000, Quadro 5000 Quadro 6000 and Tesla M2070Q.
NVIDIA Quadro FX 2800M graphics Generation 2 (via graphics mezzanine card)
NOTE: Workstation class performance for professional 2D graphics, mid/mid 3D graphics.
Supported on HP ProLiant WS460c G6 only. Not compatible and supported with HP ProLiant
BL server blades.
Memory size/type
1GB / DDR3
Memory interface
256-bit
Cuda Cores
96
Number of displays
Up to two displays per FX2800M 1GB card. May only be configured
with one card.
DA - 13429 Worldwide QuickSpecs — Version 27 — 8.31.2012
Page 7
QuickSpecs
HP ProLiant WS460c Generation 6 (G6)
Workstation Blade
Standard Features
Graphics driver
Single, unified driver compatible with FX 880M, FX 2800M, Quadro
4000 , Quadro 5000 Quadro 6000 and Tesla M2070Q.
Ultra - High End PCI Express Adapters For WS460c Graphics
Expansion Blade Only
NVIDIA Quadro 4000 graphics (Single wide PCIe-x16 in graphics expansion blade)
NOTE: Workstation class performance for professional 3D graphics. Supported on HP
WS460c G6 Graphics Expansion Blade only. Not compatible and supported with HP ProLiant
BL server blades.
Memory size/type
2GB/ GDDR5
Memory interface
256-bit
Cuda Cores
256
Graphics driver
Single, unified driver compatible with FX 880M, FX 2800M, Quadro
4000, Quadro 5000 Quadro 6000 and Tesla M2070Q.
NVIDIA Quadro 5000 graphics (via PCI express graphics card)
NOTE: Workstation class performance for ultra high end professional 3D graphics. Supported
on HP WS460c G6 Graphics Expansion Blade only. Not compatible and supported with HP
ProLiant BL server blades.
Memory size/type
Memory interface
Cuda Cores
Graphics driver
2.5 GB GDDR5
320-bit
352
New driver for Quadro 5000
Insertion of (1) PCIe graphic cards provides x16;
Insertion of (2) PCIe graphic cards provides x8
NVIDIA Quadro 6000 graphics (via PCI express graphics card)
NOTE: Workstation class performance for ultra high end professional 3D graphics. Supported
on HP WS460c G6 Graphics Expansion Blade only. Not compatible and supported with HP
ProLiant BL server blades.
Memory size/type
6.0 GB GDDR5
Memory interface
384-bit
Cuda Cores
448
Graphics driver
Unified driver for Quadro 5000 and Quadro 6000
Insertion of (1) PCIe graphic cards provides x16;
Insertion of (2) PCie graphic cards provides x8
NVIDIA Tesla M2070Q 6GB Module (Double wide PCIe-x16 in graphics expansion blade)
NOTE: General Purpose GPU for high performance computing, advanced and remote
visualization in a datacenter. Supported on HP WS460c G6 Graphics Expansion Blade only.
Not compatible and supported with HP ProLiant BL server blades.
Memory size/type
6GB GDDR5
Memory interface
384-bit
Cuda Cores
448
AMD Firestream FS9350 Compute Accelerator (Single wide PCIe-x16 in graphics
expansion blade)
NOTE: General Purpose GPU for high-performance computing and large data center, scaleout deployments. Supported on HP WS460c G6 Graphics Expansion Blade only. Not
compatible and supported with HP ProLiant BL server blades.
Memory size/type
2 GB GDDR5
Stream Cores
1440
DA - 13429 Worldwide QuickSpecs — Version 27 — 8.31.2012
Page 8
HP ProLiant WS460c Generation 6 (G6)
Workstation Blade
QuickSpecs
Standard Features
Integrated
Manageability
HP Integrated Lights-Out 2 (iLO 2) management processor
Storage Controller
Type
HP Smart Array P410i Controller (RAID 0/1)
Available Options: 256MB cache, Battery-Backed Write Cache (BBWC) module for 256MB
cache, 512MB cache with Battery Backed Write Cache (BBWC).
NOTE: 3Gb (6Gb Capable) SAS / 1.5Gb (3Gb Capable) SATA.
NOTE: Supports two (2) Small Form Factor (SFF) Hot Plug drive bays.
NOTE: HP Smart Array Advanced Pack not supported on WS460c G6.
Maximum Internal
Storage
Hot Plug SAS
Hot Plug SATA
Hot Plug SATA SSD
Hot Plug SAS SSD
Graphics
Integrated ATI RN-50, 32 MB video memory (On-board)
2TB
2TB
800GB
1.6TB
2 x 1TB Serial SCSI
2 x 1TB SATA
2 x 400GB SATA SSD
2 x 800GB SAS SSD
Resolution Color
Depths
1600 x 1200, 64K, 256, 16
1280 x 1024, 16.7M, 64k, 256, 16
1024 x 768, 16.7M, 64k, 256,16
800 x 600, 16.7M, 64k, 256, 16
640 x 480, 16.7M, 64k, 256, 16
NOTE: Maximum resolution available via HP Integrated Lights-Out 2 (iLO 2) remote console is
1280 x 1024.
NOTE: On-board graphics.
Fibre Channel SupportTwo (2) optional Fibre Channel HBAs are supported by the HP ProLiant WS460c G6. Both
mezzanine circuit boards connect directly to the server blade system board. These Fibre
Channel HBAs are available via option kits and must be ordered separately.
HBA mezzanine card option kits:
Emulex LPe1105 FC Dual Channel 4Gb, PCI-E-to-Fibre Channel Host Bus Adapter (PN
403621-B21)
Based on the same field-proven ASIC, firmware, and driver technology as Emulex's
renowned LPe1150 HBA, the Emulex LPe1105-HP is fully driver compatible with all
Emulex HBAs
QLogic QMH2462 4Gb FC HBA for HP c-Class BladeSystem (PN 403619-B21)
Uses common drivers which means that customers can standardize on one QLogic
driver whether they are using the QMH2462 or other HBAs powered by QLogic
Emulex and QLogic Fibre Channel HBAs for HP BladeSystem c-Class feature:
Optimal performance utilizing PCI Express
4/2/1Gb/s auto negotiating speeds (4Gb HBAs)
Dual-ports for redundant path connections
Optimized for HP Storage and supported by third party SAN vendors
Support for the following operating system environments
Genuine Microsoft® Windows 7.0® Business (32-bit and 64-bit)
Genuine Microsoft® Windows Vista® Business (32-bit and 64-bit1)
DA - 13429 Worldwide QuickSpecs — Version 27 — 8.31.2012
Page 9
QuickSpecs
HP ProLiant WS460c Generation 6 (G6)
Workstation Blade
Standard Features
Genuine Microsoft® Windows® XP Professional (32-bit with SP32 and 64-bit with SP21)
RedHat Enterprise Linux version 4.8 or 5.3 (64-bit)
Microsoft® Windows Server 2008 R2 SP1 (64-bit)
NOTE: For Genuine Microsoft® Windows Vista® Business (32-bit and 64-bit) drivers please
visit ProLiant Support Pack at:
http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?
lang=en&cc=US&s
wItem=MTX-aa7e24c055c643529cf479863b&prodTypeId=18964&prodSeriesId=3716246
NOTE: For Genuine Microsoft® Windows® XP Professional (64-bit with SP2) drivers please
visit ProLiant Support Pack at:
http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?
lang=en&cc=US&s
wItem=MTX-aa7e24c055c643529cf479863b&prodTypeId=18964&prodSeriesId=3716246
NOTE: For Genuine Microsoft® Windows® XP Professional (32-bit with SP3) drivers please
visit
Emulex / Qlogic website at: http://www.emulex.com/downloads/hp.html and Qlogic:
http://driverdownloads.qlogic.com/QLogicDriverDownloads_UI/Product_detail_New.aspx?
oemid=
21&companyid=4
Compatible SAN
HP ProLiant WS460c G6 workstation blades are optimized for HP Storage MSA, EVA and XP.
HP ProLiant 460c G6 server blades are compatible with select 3rd party SANs (please see
blade storage page for more details: http://h18000.www1.hp.com/products/servers/proliantbl/c-class/storage.html
NOTE: HP ProLiant WS460c G6 does not support boot from SAN.
HP Virtual Connect
HP Virtual Connect in an interconnect option for BladeSystem c-Class that simplifies server
connectivity to data and storage networks, and reduces costs. Unique HP Flex-10 and
FlexFabric technologies make maximum use of network bandwidths, provide dynamic tuning
and enable extreme flexibility to meet individual server and infrastructure requirements. HP
Virtual Connect Enterprise Manager (VCEM) provides a central console to administer network
connections and workloads for thousands of servers. For more information on Virtual Connect
Ethernet, Fibre Channel, Converged Network and management options see:
www.hp.com/go/virtualconnect
DA - 13429 Worldwide QuickSpecs — Version 27 — 8.31.2012
Page 10
QuickSpecs
HP ProLiant WS460c Generation 6 (G6)
Workstation Blade
Standard Features
HP Insight
HP Integrated Lightsmanagement software Out 2 (iLO 2)
HP Insight Control
HP Integrated Lights-Out (iLO) simplifies server setup, health
monitoring, power and thermal control, and lights-out remote
administration of ProLiant ML, DL, BL servers and Workstation
Blades. HP iLO functions without additional software and can be
accessed from any location via a web browser. HP iLO unleashes the
power of the ProLiant platform and delivers the highest possible
quality of IT service to the business. For more information, visit:
www.hp.com/go/iLO
HP Insight Control, a product option, delivers essential infrastructure
management that can help save time and money by making it easy to
deploy, migrate, monitor, remote control, and optimize your IT
infrastructure through a single, simple management console.
Two versions of Insight Control are available, to serve environments
requiring either a Linux-based or a Windows-based central
management server: HP Insight Control for Linux*, and HP Insight
Control. See www.hp.com/go/insightcontrol.
HP Insight Control includes one year of 24 x 7 HP Software Technical
Support and Update Service ensuring rapid access to HP support
staff and proactive delivery of software updates. For more information
about this service, please visit: http://www.hp.com/services/insight.
NOTE: * HP Insight Control for Linux not supported on the WS460c
G6.
High Performance
Clusters
HP Cluster Platforms
HP Cluster Platforms are specifically engineered, factory-integrated
large-scale ProLiant clusters optimized for High Performance
Computing, with a choice of servers, networks and software.
Operating system options include specially priced offerings for Red
Hat Enterprise Linux and SUSE Linux Enterprise Server, as well as
Microsoft Windows HPC Server. A Cluster Platform Configurator
simplifies ordering. http://www.hp.com/go/clusters
HP HPC Interconnects High Performance Computing (HPC) interconnect technologies are
available for this server as part of the HP Cluster Platform portfolio.
These high-speed InfiniBand and Gigabit interconnects are fully
supported by HP when integrated within an HP cluster. Flexible,
validated solutions can be defined with the help of configuration tools.
http://www.hp.com/techservers/clusters/ucp/index.html
HP Insight Cluster
HP Insight Cluster Management Utility (CMU) is an HP-licensed and
Management Utility
HP-supported suite of tools that are used for lifecycle management of
hyperscale clusters of Linux ProLiant systems. CMU includes
software for the centralized provisioning, management and monitoring
of nodes. CMU makes the administration of clusters user friendly,
efficient, and effective. http://www.hp.com/go/cmu
HP HPC Linux Value
HP HPC Linux Value Pack (Value Pack) is an HP-licensed and HPPack
supported option to HP Insight CMU, for the development and
deployment of applications on HPC Cluster Platforms. Value Pack
includes the Platform LSF workload scheduler and Platform
Application Center, as well as the HP-MPI parallelization library. HP
HPC Linux Value Pack
DA - 13429 Worldwide QuickSpecs — Version 27 — 8.31.2012
Page 11
QuickSpecs
HP ProLiant WS460c Generation 6 (G6)
Workstation Blade
Standard Features
Operating Systems
Server Operating System:
Support for HP
Microsoft® Windows Server 2008 R2 SP1 (64-bit) Standard, Enterprise and DataCenter
ProLiant Workstations editions
Citrix XenServer 6 Enterprise and Platinum editions
Client Operating Systems:
Genuine Microsoft® Windows 7.0® Business (32-bit and 64-bit)
Microsoft Windows Vista Business SP2 (32-bit & 64-bit)
Microsoft Windows XP Professional SP3 (32-bit)
Microsoft Windows XP Professional x64 edition with SP2
Red Hat Enterprise Linux (RHEL) 4.8 and 5.3 (64-bit only)
Availability
Dual-Port Fibre Channel Mezzanine Card options for redundant SAN connection
Two (2) hot-plug SAS hard drive bays and integrated RAID (HP Smart Array P410i
Controller)
Optional Battery-backed write cache module for integrated RAID controller
Redundant ROM
Advanced ECC Memory
Industry Standard
Compliance
PCI 2.2 Compliant
WOL Support
SB 2.0 Support
Security
Power-on password
Administrator's password
Integrated Lights-Out 2 has 12 customizable user accounts and SSL encryption
Integrated Lights-Out 2 can be disabled via a Global Setting
Factory Express
Portfolio for Servers
and Storage
HP Factory Express offers configuration, customization, integration and deployment services
for HP servers and storage products. Customers can choose how their factory solutions are
built, tested, integrated, shipped and deployed.
Factory Express offers service packages for simple configuration, racking, installation, complex
configuration and design services as well as individual factory services, such as image loading,
asset tagging, and custom packaging. HP products supported through Factory Express include
a wide array of servers and storage: HP Integrity, HP ProLiant, HP ProLiant Server Blades, HP
BladeSystem, HP 9000 servers as well as the MSAxxxx, VA7xxx, EVA, XP, rackable tape
libraries and configurable network switches.
For more information on Factory Express services on your specific server model please
contact your sales representative or go to: http://www.hp.com/go/factory-express.
HP Enterprise
Configurator
The HP e-Configure Enterprise Configurator now provides factory default racking for our HP
hardware portfolio. This approach is aligned with our strategic direction to meet the needs and
expectations of our valued customers. If you require "custom" rack configuration, please
contact HP's Customer Business Center or an Authorized Partner for assistance.
http://www.hp.com/products/configurator.
DA - 13429 Worldwide QuickSpecs — Version 27 — 8.31.2012
Page 12
QuickSpecs
HP ProLiant WS460c Generation 6 (G6)
Workstation Blade
Service and Support
Service and Support
HP Technology Services for Industry Standard Servers and BladeSystem
Capitalizing on HP ProLiant server and HP BladeSystem capabilities requires a service partner
who understands your increasingly complex business technology environment. That's why it
makes sense to team up with the people who know HP infrastructure hardware and software
best - the experienced professionals at HP Services.
What HP ProLiant and BladeSystem Services can do for you
HP ProLiant and BladeSystem Services can help you design, deploy, test, integrate, support,
and manage IT and infrastructure solutions. This way, HP proposes services solutions that
include more than just uplift of base warranty. You can get the support you need by choosing
from one of a number of service packaged solutions we have designed to address wider set of
customer support needs:.
HP Technology Services meets business challenges with services offered in three
packages
Optimized Care Package, Standard Care Package, and Basic Care Package - available for
each product group. Such packaged solutions enable customers to optimize technology
operations, minimize risk and drive better business outcomes with easy-to-buy, easy-to-use
scalable support packages for servers, storage, networking and software.
Optimized Care
Package
Supports maintaining servers at optimum performance availability
HP Installation and Startup Service for HP BladeSystem c-Class Infrastructure for
c3000/c7000 enclosure
Provides for the installation and startup of a BladeSystem c3000 Infrastructure in a single
blade enclosure including hardware and software, including deployment of OS, HP SIM, RDP,
RDP, PMP and VPM.
http://h20195.www2.hp.com/V2/GetPDF.aspx/4AA0-5964ENW.pdf
3-Year HP Critical Advantage for c3000/c7000 enclosure + 3-Year HP Critical Advantage
for Blade server
Provides end-to-end infrastructure support solution for business critical applications running on
virtualized/x86 infrastructures, enabling the customers to cost effectively build, operate, and
continuously improve their IT environment.
http://h20195.www2.hp.com/V2/GetDocument.aspx?docname=4AA3-1772ENW
HP Installation and Startup Service for HP BladeSystem c-Class Enhanced Network
HP Provides for the configuration and testing of BladeSystem Ethernet interconnect switches
to facilitate proper implementation of network protocols and access to advanced features.
http://h20195.www2.hp.com/V2/GetPDF.aspx/4aa0-5969ENW.pdf
Additional Services: Virtualization Services - Strategy, Design, Transition, Operation,
Continual Service Improvement.
DA - 13429 Worldwide QuickSpecs — Version 27 — 8.31.2012
Page 13
QuickSpecs
HP ProLiant WS460c Generation 6 (G6)
Workstation Blade
Service and Support
Standard Care
Package
Package that maintains high level of server availability
HP Installation and Startup Service for HP BladeSystem c-Class Infrastructure for
c3000/c7000 enclosure
Provides for the installation and startup of a BladeSystem c3000 Infrastructure in a single
blade enclosure including hardware and software, including deployment of OS, HP SIM, RDP,
RDP, PMP and VPM.
http://h20195.www2.hp.com/V2/GetPDF.aspx/4AA0-5964ENW.pdf
HP Installation and Startup Service for HP BladeSystem c-Class Enhanced Network
HP Provides for the configuration and testing of BladeSystem Ethernet interconnect switches
to facilitate proper implementation of network protocols and access to advanced features.
http://h20195.www2.hp.com/V2/GetPDF.aspx/4aa0-5969ENW.pdf
3-Year, HP 6 hour Hardware Support Onsite Call-to-Repair Service for c3000/c7000
enclosure + 3-Year, HP 6 hour Hardware Support Onsite Call-to-Repair Service for Blade
server
Provides an IT manager with a team of support specialists who will quickly begin
troubleshooting the system to help return the hardware to operating condition within 6 hours of
the initial service request to the HP Global Solution Center.
http://h20195.www2.hp.com/V2/GetPDF.aspx/5981-6636ENN.pdf
3-Year , HP 24x7 Software Support for Insight Control
Provides for the deployment and basic configuration of HP Insight Control on HP ProLiant ML
and DL series servers or HP BladeSystem servers.
http://h20195.www2.hp.com/V2/GetPDF.aspx/5981-6645EEE.pdf
Additional Services: Software OS (Microsoft, Linux (SUSE/Red Hat) & VMware Installation &
Start Up and Software Support); Microsoft or Linux or VMware education courses; +60
Proactive Select Credits, Factory Express.
Basic Care Package
Delivers minimum recommended support service level
HP Installation and Startup Service for HP BladeSystem c-Class Infrastructure for
c3000/c7000 enclosure
Provides for the installation and startup of a BladeSystem c3000 Infrastructure in a single
blade enclosure including hardware and software, including deployment of OS, HP SIM, RDP,
RDP, PMP and VPM.
http://h20195.www2.hp.com/V2/GetPDF.aspx/4AA0-5964ENW
3-Year, HP 24x7 4 hour Response, Hardware Support Onsite Service for c3000/c7000
enclosure + 3-Year, HP 24x7 4 hour Response, Hardware Support Onsite Service for
Blade server
Provides you with rapid remote support and if required an HP authorized representative who
will arrive on site any time and day of the year to begin hardware maintenance service within 4
hours of the service request being logged.
http://h20195.www2.hp.com/V2/GetPDF.aspx/5982-6547EEE.pdf
3-Year , HP 24x7 Software Support for Insight Control
Provides for the deployment and basic configuration of HP Insight Control on HP ProLiant ML
and DL series servers or HP BladeSystem servers.
http://h20195.www2.hp.com/V2/GetPDF.aspx/5981-6645EEE.pdf
Additional Services: Startup Blade System c-Cass Enhanced Network Service; Software OS
(Microsoft, Linux (SUSE/Red Hat) & VMware Installation & Start Up and Software Support);
+30 Proactive Select Credits, Factory Express.
DA - 13429 Worldwide QuickSpecs — Version 27 — 8.31.2012
Page 14
QuickSpecs
HP ProLiant WS460c Generation 6 (G6)
Workstation Blade
Service and Support
Insight Remote
Support
The packages include HP Insight Remote Support that uses proven technology to deliver
secure, reliable 24x7 remote monitoring, diagnoses, and problem resolution. It is available at
no additional cost to all warranty, HP Care Pack Service, and service agreement customers.
For more information To learn more on HP ProLiant servers and HP BladeSystem servers, please contact your HP
sales representative or HP Authorized Channel Partner. Or visit:
www.hp.com/services/bladesystem
DA - 13429 Worldwide QuickSpecs — Version 27 — 8.31.2012
Page 15
QuickSpecs
HP ProLiant WS460c Generation 6 (G6)
Workstation Blade
Models
FX 880M graphics preconfigured model
NOTE: For the Standard Features shipped in the "Factory Integrated Models", please see the "Configuration Information
- Factory Integrated Models" section.
NOTE: Not all models are available in all regions. Check with your local country HP offices for availability.
NOTE: Pre-configured models ship with the configurations below. Options can be selected from the Core or Additional
options section of this QuickSpecs.
NOTE: HP does not allow factory integration of options into pre-configured models. Any additional options purchased
will be shipped separately.
NOTE: If you desire a custom configuration please see "Configuration Information - Factory Integrated Models" section
of this QuickSpecs.
HP ProLiant WS460c Processor(s)
(1) Intel® Xeon® E5630 (2.53GHz/4-core/12MB/80W, DDR3-1066,
G6 E5630 1P 2GB-R
HT, Turbo 1/1/2/2) Processor
Dual FX880M
Cache Memory
12MB and 8MB shared L3 cache
Workstation
Memory
2GB (1 x 2 GB) PC3-10600 (DDR3-1333) Registered DIMMs
632290-B21
(RDIMMs)
Graphics Adapter
(2) NVIDIA Quadro FX 880M with 1GB memory
Network Adapter
Embedded NC532i Dual Port Flex-10 10GbE Multifunction Server
Adapter and one (1) additional 10/100 server adapter dedicated to
iLO 2 management
Storage Controller
Integrated HP Smart Array P410i Controller
NOTE: Optional 256MB or 512MB Battery-Backed Write Cache
available. Please see the Storage Controllers section listed in
Additional Options section of this QuickSpecs
Hard Drives
None ship standard
NOTE: Client operating systems require local hard disk drives. Order
desired capacity/performance drives separately.
Internal Storage
SAS: 2TB (2 x 1TB SAS) - Maximum
SATA: 2TB (2 x 1TB SATA) - Maximum
Optical Drive
None
Operating System
None
NOTE: Client OS license and software not included.
Form Factor
Up to eight (8) half-height blades supported in the HP BladeSystem
c3000 Enclosure
Up to sixteen (16) half-height blades supported in HP BladeSystem
c7000 Enclosure
DA - 13429 Worldwide QuickSpecs — Version 27 — 8.31.2012
Page 16
HP ProLiant WS460c Generation 6 (G6)
Workstation Blade
QuickSpecs
Models
FX 2800M graphics preconfigured model
HP ProLiant WS460c
G6 E5640 1P 4GB-R
Single FX2800M
Workstation
632291-B21
Processor(s)
Cache Memory
Memory
Graphics Adapter
Network Adapter
Storage Controller
Hard Drives
Internal Storage
Optical Drive
Operating System
Form Factor
(1) Intel® Xeon® E5640 (2.66GHz/4-core/12MB//80W, DDR3-1066,
HT, Turbo 1/1/2/2) Processor
12MB and 8MB shared L3 cache
4GB (2 x 2 GB) PC3-10600 (DDR3-1333) Registered DIMMs
(RDIMMs)
(1) NVIDIA Quadro FX 2800M with 1GB memory
Embedded NC532i Dual Port Flex-10 10GbE Multifunction Server
Adapter and one (1) additional 10/100 server adapter dedicated to
iLO 2 management
Integrated HP Smart Array P410i Controller
NOTE: Optional 256MB or 512MB Battery-Backed Write Cache
available. Please see the Storage Controllers section listed in
Additional Options section of this QuickSpecs
None ship standard
NOTE: Client operating systems require local hard disk drives. Order
desired capacity/performance drives separately.
SAS: 2TB (2 x 1TB SAS) - Maximum
SATA: 2TB (2 x 1TB SATA) - Maximum
None
None
NOTE: Client OS license and software not included.
Up to eight (8) half-height blades supported in the HP BladeSystem
c3000 Enclosure
Up to sixteen (16) half-height blades supported in HP BladeSystem
c7000 Enclosure
DA - 13429 Worldwide QuickSpecs — Version 27 — 8.31.2012
Page 17
QuickSpecs
HP ProLiant WS460c Generation 6 (G6)
Workstation Blade
Configuration Information - Factory Integrated Models
NOTE: This section lists some of the steps required to configure a Factory Integrated Model. To ensure only valid
configurations are ordered, HP recommends the use of an HP approved configurator. Contact your local sales
representative for information on CTO product offerings and requirements.
NOTE: Configure-to-order (CTO) servers must start with a CTO Chassis.
NOTE: HP does not allow factory integration of options into standard models listed above. Configure-to-order server blades
must start with a CTO Blade.
NOTE: FIO indicates that this option is only available as a Factory Installable Option.
Step 1: Base Server Blade Configuration (Select a configurable Blade)
HP Models
HP ProLiant WS460c G6 Configure-to-order Blade
NOTE: Single-width, half-height bade with two mezzanine card slots available.
HP WS460c G6 Graphics Expansion Configure-to-order Blade
NOTE: Double-width half-height blade with two, full-length, PCIe x8 slots. No
mezzanine card slots on base blade are currently available.
Configurable Model ships with:
Integrated NC532i Dual Port Flex-10 10GbE Multifunction Server Adapter,
Integrated HP Smart Array P410i Controller (RAID 0/1) (1) additional 10/100
server adapter dedicated to iLO 2 management with Integrated Lights-Out 2
Standard Blade Edition
580139-B21
594935-B21
Step 2: Choose Required Options (one of the following from each list unless
otherwise noted)
HP Processors
HP Memory
NOTE: HP ProLiant WS460c G6 shares same processor modules with BL460c
G6 server. If two processors are desired, select one xxxxxx-L21 and one xxxxxxB21.
Six-Core Processor Option Kits
HP BL460c G7 Intel® Xeon® X5675 (3.06GHz/6-core/12MB/95W) FIO
Processor Kit
HP BL460c G7 Intel® Xeon® E5649 (2.53GHz/6-core/12MB/80W) FIO
Processor Kit
HP BL460c G7 Intel® Xeon® E5645 (2.40GHz/6-core/12MB/80W) FIO
Processor Kit
Quad-Core Processor Option Kits
HP BL460c G6 Intel® Xeon® E5640 (2.66GHz/4-core/12MB/80W) FIO
Processor Kit
HP WS460c G6 Intel® Xeon® E5630 (2.53GHz/4-core/12MB/80W) FIO
Processor Kit
HP WS460c G6 Intel® Xeon® E5620 (2.40GHz/4-core/12MB/80W) FIO
Processor Kit
Registered DIMMS (RDIMMs)
HP 2GB (1x2GB) Dual Rank x8 PC3-10600 (DDR3-1333) Registered CAS-9
Memory Kit
HP 4GB (1x4GB) Dual Rank x4 PC3-10600 (DDR3-1333) Registered CAS-9
Memory Kit
HP 4GB (1x4GB) Single Rank x4 PC3-10600 (DDR3-1333) Registered CAS-9
Memory Kit
HP 4GB (1x4GB) Single Rank x4 PC3L-10600 (DDR3-1333) Registered CAS-9
Low Power Memory Kit
HP 8GB (1x8GB) Dual Rank x4 PC3-10600 (DDR3-1333) Registered CAS-9
Memory Kit
DA - 13429 Worldwide QuickSpecs — Version 27 — 8.31.2012
637406-L21
637410-L21
637412-L21
595729-L21
601459-L21
603589-L21
500656-B21
500658-B21
593339-B21
604504-B21
500662-B21
Page 18
QuickSpecs
HP ProLiant WS460c Generation 6 (G6)
Workstation Blade
Configuration Information - Factory Integrated Models
HP 8GB (1x8GB) Dual Rank x4 PC3L-10600 (DDR3-1333) Registered CAS-9
Low Power Memory Kit
HP 16GB (1x16GB) Quad Rank x4 PC3-8500 (DDR3-1066) Registered CAS-7
Memory Kit
Unbuffered with ECC DIMMs (UDIMMs)
HP 1GB (1x1GB) Single Rank x8 PC3-10600 (DDR3-1333) Unbuffered CAS-9
Memory Kit
HP 2GB (1x2GB) Dual Rank x8 PC3-10600 (DDR3-1333) Unbuffered CAS-9
Memory Kit
HP 4GB (1x4GB) Dual Rank x8 PC3-10600 (DDR3-1333) Unbuffered CAS-9
Memory Kit
NOTE: All DDR3 memory option kits consist of one DIMM per kit. For detailed
memory configuration rules and guidelines, please use the Online DDR3
Memory Configuration Tool: www.hp.com/go/ddr3memory-configurator.
NOTE: Kits described as LP include Low Power DIMMs. For more information on
ProLiant Energy Efficient Features, see: www.hp.com/go/proliant-energyefficient.
604506-B21
500666-B21
500668-B21
500670-B21
500672-B21
Step 3: Choose Additional Factory Integratable Options (one of the following from
each list unless otherwise noted)
HP Graphics Options
NOTE: Choose from following graphics mezzanine cards for use with the singlewidth HP ProLiant WS460c G6 model (P/N 580139-B21).
NVIDIA Quadro FX880M (1G) Mezz Graphics Single Card FIO Kit
HP FX880M Mezzanine Graphics Dual FIO Kit
NVIDIA Quadro FX2800M (1G) Mezz Graphics Single Card FIO Kit
NOTE: Single card kit can support up to two displays as dual-display
configuration on the access client using HP Remote Graphics Software.
NOTE: Dual card kit can support up to four displays as quad-display
configuration on the access client using HP Remote Graphics Software.
NOTE: Choose following standard PCIe graphics card for use with the doublewidth HP ProLiant WS460c model (P/N 594935-B21).
NVIDIA Quadro 4000 2GB PCI-E Adapter
NVIDIA Quadro 5000 2.5GB PCI-E Adapter
NVIDIA Quadro 6000 6GB PCI-E Adapter
AMD Firestream FS9350 Compute Accelerator
NVIDIA Tesla M2070Q 6GB GPU Graphics Module
594980-B21
632294-B21
594936-B21
655933-B21
655934-B21
655935-B21
A0K01A
A0C39A
Step 4: Choose Additional Options for Factory Integration
NOTE: For additional options, please refer to the "Core Options" and "Additional Options" section below. For additional
options, including server blade enclosures interconnect and mezzanine options and power subsystem options; please see
the Core Options and Additional sections below; or the following:
HP BladeSystem c3000 Enclosure QuickSpecs:
http://h18000.www1.hp.com/products/quickspecs/12790_div/12790_div.html
HP BladeSystem c7000 Enclosure QuickSpecs:
http://h18000.www1.hp.com/products/quickspecs/12810_div/12810_div.html
and HP BladeSystem c-Class Interconnect and Mezzanine Components:
http://h18004.www1.hp.com/products/blades/components/c-class-interconnects.html
http://h18004.www1.hp.com/products/blades/components/c-class-adapters.html.
DA - 13429 Worldwide QuickSpecs — Version 27 — 8.31.2012
Page 19
QuickSpecs
HP ProLiant WS460c Generation 6 (G6)
Workstation Blade
Core Options
NOTE: Some options may not be integrated at the factory. To ensure only valid configurations are ordered, HP
recommends the use of an HP approved configurator. Contact your local sales representative for additional information.
NOTE: For additional options, please refer to the "Core Options" and "Additional Options" sections below.
HP Fiber Channel
Emulex LPe1105 4Gb Fibre Channel Host Bus Adapter for c-Class
403621-B21
Mezzanine Options
BladeSystem
QLogic QMH2462 4Gb Fibre Channel Host Bus Adapter for c-Class
403619-B21
BladeSystem
NOTE: Boot from SAN functionality not supported.
HP Processors
Six-Core Process Option Kits
HP BL460c G7 Intel® Xeon® X5675 (3.06GHz/6-core/12MB/95W) Processor
Kit
HP BL460c G7 Intel® Xeon® E5649 (2.53GHz/6-core/12MB/80W) Processor
Kit
HP BL460c G7 Intel® Xeon® E5645 (2.40GHz/6-core/12MB/80W) Processor
Kit
Quad-Core Process Option Kits
HP BL460c G6 Intel® Xeon® E5640 (2.66GHz/4-core/12MB/80W) Processor
Kit
HP WS460c G6 Intel® Xeon® E5630 (2.53GHz/4-core/12MB/80W) Processor
Kit
HP WS460c G6 Intel® Xeon® E5620 (2.40GHz/4-core/12MB/80W) Processor
Kit
HP BL460c G6 Intel® Xeon® E5520 (2.26GHz/4-core/8MB/80W) Processor
Kit
Dual-Core Process Option Kits
HP BL460c G6 Intel® Xeon® E5502 (1.86GHz/2-core/4MB/80W) Processor
Kit
HP Memory
Registered DIMMS (RDIMMs)
HP 2GB (1x2GB) Dual Rank x8 PC3-10600 (DDR3-1333) Registered CAS-9
Memory Kit
HP 4GB (1x4GB) Dual Rank x4 PC3-10600 (DDR3-1333) Registered CAS-9
Memory Kit
HP 4GB (1x4GB) Single Rank x4 PC3-10600 (DDR3-1333) Registered CAS-9
Memory Kit
HP 4GB (1x4GB) Single Rank x4 PC3L-10600 (DDR3-1333) Registered CAS9 Low Power Memory Kit
HP 8GB (1x8GB) Dual Rank x4 PC3-10600 (DDR3-1333) Registered CAS-9
Memory Kit
HP 8GB (1x8GB) Dual Rank x4 PC3L-10600 (DDR3-1333) Registered CAS-9
Low Power Memory Kit
HP 16GB (1x16GB) Quad Rank x4 PC3-8500 (DDR3-1066) Registered CAS7 Memory Kit
Unbuffered with ECC DIMMs (UDIMMs)
HP 1GB (1x1GB) Single Rank x8 PC3-10600 (DDR3-1333) Unbuffered CAS-9
Memory Kit
HP 2GB (1x2GB) Dual Rank x8 PC3-10600 (DDR3-1333) Unbuffered CAS-9
Memory Kit
DA - 13429 Worldwide QuickSpecs — Version 27 — 8.31.2012
637406-B21
637410-B21
637412-B21
595729-B21
601459-B21
603589-B21
507799-B21
507802-B21
500656-B21
500658-B21
593339-B21
604504-B21
500662-B21
604506-B21
500666-B21
500668-B21
500670-B21
Page 20
QuickSpecs
HP ProLiant WS460c Generation 6 (G6)
Workstation Blade
Core Options
HP 4GB (1x4GB) Dual Rank x8 PC3-10600 (DDR3-1333) Unbuffered CAS-9
Memory Kit
NOTE: All DDR3 memory option kits consist of one DIMM per kit. For detailed
memory configuration rules and guidelines, please use the Online DDR3
Memory Configuration Tool: www.hp.com/go/ddr3memory-configurator.
NOTE: Kits described as LP include Low Power DIMMs. For more information
on ProLiant Energy Efficient Features, see:
http://h18004.www1.hp.com/products/servers/platforms/energyefficient/.
HP Hard Drives
SAS Hot Plug SFF (2.5-inch) Enterprise (ENT) Drives
HP 900GB 6G SAS 10K rpm SFF (2.5-inch) Dual Port Enterprise 3yr
Warranty Hard Drive
HP 600GB 6G SAS 10K rpm SFF (2.5-inch) Dual Port Enterprise 3yr
Warranty Hard Drive
HP 450GB 6G SAS 10K rpm SFF (2.5-inch) Dual Port Enterprise 3yr
Warranty Hard Drive
HP 300GB 6G SAS 15K rpm SFF (2.5-inch) Hot Plug Enterprise 3 yr Warranty
Hard Drive
HP 300GB 6G SAS 10K rpm SFF (2.5-inch) Dual Port Enterprise 3yr
Warranty Hard Drive
HP 146GB 6G SAS 15K rpm SFF (2.5-inch) Dual Port Enterprise 3yr
Warranty Hard Drive
SAS Hot Plug SFF (2.5-inch) Midline (MDL) Drives
HP 1TB 6G SAS 7.2K rpm SFF (2.5-inch) Dual Port Midline 1yr Warranty
Hard Drive
HP 500GB 6G SAS 7.2K rpm SFF (2.5-inch) Dual Port Midline 1yr Warranty
Hard Drive
NOTE: Please see QuickSpecs for Technical Specifications and additional
information:
http://h18000.www1.hp.com/products/quickspecs/12244_div/12244_div.html
(Worldwide)
6G SAS Hot Plug Enterprise Performance Solid State Drives
HP 400GB 6G SAS SLC SFF (2.5-inch) Enterprise Performance 3yr Warranty
Solid State Drive
HP 200GB 6G SAS SLC SFF (2.5-inch) Enterprise Performance 3yr Warranty
Solid State Drive
6G SAS Hot Plug Enterprise Mainstream Solid State Drives
HP 800GB 6G SAS MLC SFF (2.5-inch) Enterprise Mainstream 3yr Warranty
Solid State Drive
HP 400GB 6G SAS MLC SFF (2.5-inch) Enterprise Mainstream 3yr Warranty
Solid State Drive
HP 200GB 6G SAS MLC SFF (2.5-inch) Enterprise Mainstream 3yr Warranty
Solid State Drive
NOTE: Please see the QuickSpecs for Technical Specifications and additional
information:
http://h18000.www1.hp.com/products/quickspecs/14038_div/14038_div.html
(Worldwide)
SATA Hot Plug SFF (2.5-inch) Midline (MDL) Drives
HP 1TB 3G SATA 7.2K rpm SFF (2.5-inch) Hot Plug Midline 1yr Warranty
Hard Drive
DA - 13429 Worldwide QuickSpecs — Version 27 — 8.31.2012
500672-B21
619291-B21
581286-B21
581284-B21
627117-B21
507127-B21
512547-B21
605835-B21
507610-B21
632494-B21
632492-B21
632506-B21
632504-B21
632502-B21
625609-B21
Page 21
QuickSpecs
HP ProLiant WS460c Generation 6 (G6)
Workstation Blade
Core Options
HP 500GB 3G SATA 7.2K rpm SFF (2.5-inch) Midline 1yr Warranty Hard
Drive
NOTE: Please see QuickSpecs for Technical Specifications and additional
information:
http://h18000.www1.hp.com/products/quickspecs/13021_div/13021_div.html
(Worldwide)
SATA Hot Plug 2.5" Enterprise Mainstream Solid State Drives
HP 400GB 3G SATA MLC SFF (2.5-inch) Enterprise Mainstream 3yr Warranty
Solid State Drive
HP 200GB 3G SATA MLC SFF (2.5-inch) Enterprise Mainstream 3yr Warranty
Solid State Drive
HP 100GB 3G SATA MLC SFF (2.5-inch) Enterprise Mainstream 3yr Warranty
Solid State Drive
NOTE: Please see QuickSpecs for Technical Specifications and additional
information:
http://h18000.www1.hp.com/products/quickspecs/13415_div/13415_div.html
(Worldwide)
NOTE: Hard drives have either a one year or three year warranty; refer to the
specific hard drive QuickSpecs for details.
NOTE: The hard drive options are not required when configuring a Drive-less
Model.
DA - 13429 Worldwide QuickSpecs — Version 27 — 8.31.2012
507750-B21
636597-B21
636595-B21
636593-B21
Page 22
QuickSpecs
HP ProLiant WS460c Generation 6 (G6)
Workstation Blade
Additional Options
NOTE: For additional options, please refer to the "Core Options" and "Additional Options" sections below.
NOTE: Some options may not be integrated at the factory. To ensure only valid configurations are ordered, HP
recommends the use of an HP approved configurator. Contact your local sales representative for additional information.
HP Insight software
HP Integrated Lights-Out (iLO) Advanced for ProLiant BladeSystem
Remote Management
HP iLO Advanced for BladeSystem including 1yr 24x7 Support Single Server
512488-B21
License
NOTE: Customer will receive a license entitlement certificate, which must be
redeemed online or via fax in order to obtain the license activation key(s).
Includes one year of 24 x 7 HP Software Technical Support Service.
NOTE: For additional license kits please see the HP Integrated Lights-Out
(iLO) QuickSpecs at: www.hp.com/go/iLO.
High Performance
Clusters
HP Insight Cluster Management Utility 1yr 24x7 Flexible License
NOTE: This part number can be used to purchase one certificate for multiple
licenses with a single activation key. Each license is for one node (server).
Customer will receive a printed end user license agreement and license
entitlement certificate via physical shipment. The license entitlement
certificate must be redeemed online in order to obtain a license key.
NOTE: For additional license kits please see the QuickSpecs at:
http://h18004.www1.hp.com/products/quickspecs/12612_div/12612_div.html
(Worldwide)
HP Insight Cluster Management Utility 3yr 24x7 Flexible License
NOTE: These part numbers can be used to purchase one certificate for
multiple licenses and support with a single activation key. Each license is for
one node (server). Customer will receive a printed end user license
agreement and license entitlement certificate via physical shipment. The
license entitlement certificate must be redeemed online in order to obtain a
license key. Customer also will receive a support agreement.
HP Insight Cluster Management Utility Media
NOTE: Order a minimum of one license per cluster to purchase media
including software and documentation, which will be delivered to the
customer, and also licenses CMU management. No license key is delivered or
required.
NOTE: For additional license kits please see the QuickSpecs at:
http://h18004.www1.hp.com/products/quickspecs/12612_div/12612_div.html
(Worldwide)
HP High Performance Computing Linux Value Pack 1 Processor Flexible
License
NOTE: This part number can be used to purchase one certificate for multiple
licenses with a single activation key. Each license is for one socket (a.k.a.
processor). Customer will receive a printed end user license agreement and
license entitlement certificate via physical shipment. The license entitlement
certificate must be redeemed online in order to obtain a license key.
NOTE: For additional license kits please see the QuickSpecs at:
http://h18004.www1.hp.com/products/quickspecs/13485_div/13485_div.html
(Worldwide)
HP High Performance Computing Linux Value Pack Media Kit
NOTE: This part number can be used to purchase media including software
and documentation, which will be delivered to the customer.
NOTE: For additional license kits please see the QuickSpecs at:
http://h18004.www1.hp.com/products/quickspecs/13485_div/13485_div.html
(Worldwide)
DA - 13429 Worldwide QuickSpecs — Version 27 — 8.31.2012
QL803B
BD476A
BD477A
TC293B
TC294A
Page 23
QuickSpecs
HP ProLiant WS460c Generation 6 (G6)
Workstation Blade
Additional Options
HP Remote Access
HP Graphic Options
HP Remote Graphics Software (RGS) v5.4.0
NOTE: HP RGS is licensed software sold separately. Not bundled with HP
WS460c G6.
NOTE: For remote access to Windows Vista OS on blade, HP RGS version
5.3 or later is required.
NOTE: For more information on HP Remote Graphics Software, please find
HP Remote Graphics in: http://www.hp.com/go/rgs
HP RGS Desktop E-LTU/E-Media
HP RGS Desktop E-LTU/E-Media
HP RGS Desktop LTU and CD-ROM Media AW686AA
HP 1 year 9x5 3 Incidents Remote Graphics Software Technical Support
AW684AAE
AW684AA
AW686AA
UE345E
NVIDIA Quadro 4000 2GB PCI-E Adapter
NVIDIA Quadro 5000 2.5GB PCI-E Adapter
NVIDIA Quadro 6000 6GB PCI-E Adapter
655933-B21
655934-B21
655935-B21
HP Storage Controller Optional Upgrades
HP 256MB P-series Cache Upgrade
HP 650 mAh P-Series Battery
NOTE: Requires 256 MB Cache Module.
HP 1GB Flash Backed Cache
HP 512MB P-Series Battery Backed Write Cache Upgrade
NOTE: Highly recommended for optimal performance.
HP 512MB Flash Backed Write Cache
NOTE: Please see the QuickSpecs for Technical Specifications and additional
information:
http://h18000.www1.hp.com/products/quickspecs/13203_div/13203_div.html
(Worldwide)
HP c-Class Mezzanine HP 4X QDR QLogic InfiniBand Dual Port Mezzanine HCA for c-Class
Options
BladeSystem
HP 4X QDR InfiniBand ConnectX-2 Dual Port Mezzanine HCA for c-Class
BladeSystem
NOTE: QDR InfiniBand Mezzanine cards are supported with Redhat Linux
Operating System only.
NOTE: Please see the QuickSpecs for Technical Specifications and additional
information:
http://h18000.www1.hp.com/products/quickspecs/12586_div/12586_div.html
(Worldwide)
DA - 13429 Worldwide QuickSpecs — Version 27 — 8.31.2012
462968-B21
462969-B21
534562-B21
462967-B21
534916-B21
583210-B21
592519-B21
Page 24
QuickSpecs
HP ProLiant WS460c Generation 6 (G6)
Workstation Blade
Additional Options
HP Expansion Blade
HP BLc PCI Expansion Blade
NOTE: Ships with one pre-installed PCI-X connect board. Also includes one
PCIe connect board which requires installation.
NOTE: Please see the QuickSpecs for Technical Specifications and additional
information:
http://h18000.www1.hp.com/products/quickspecs/12753_div/12753_div.html
(Worldwide)
HP USB and SD
Options
HP USB 2-Button Optical Scroll Mouse
HP Care Pack Services NOTE: The HP Care Pack service part numbers below for ProLiant BL c-Class
workstation blades, cover the workstation blade and all HP branded hardware
options qualified for the workstation, purchased at the same time or afterwards,
internal to the workstation.
Hardware Services On-site Service
HP 3 year 4 hour 13x5 WS460c Workstation Blade Hardware Support
HP 3 year 4 hour 24x7 WS460c Workstation Blade Hardware Support
HP 3 year 6 hour 24x7 Call to Repair WS460c Workstation Blade Hardware
Support
DA - 13429 Worldwide QuickSpecs — Version 27 — 8.31.2012
448018-B21
DC172B
UR334E
UR336E
UR338E
Page 25
HP ProLiant WS460c Generation 6 (G6)
Workstation Blade
QuickSpecs
Memory
NOTE: Memory configurations listed do not apply to "Factory Integrated Models".
Memory Population Guidelines
For detailed memory configuration rules and guidelines, please use the Online DDR3 Memory Configuration Tool:
www.hp.com/go/ddr3memory-configurator
Some DIMM installation guidelines are summarized below:
For the HP ProLiant WS460c G6 server with twelve (12) memory slots:
There are three (3) channels per processor; six (6) channels per server
There are two (2) DIMM slots for each memory channel; twelve (12) total slots.
Memory channel 1 consists of the two (2) DIMMs that are closest to the processor
Memory channel 3 consists of the two (2) DIMMs that are furthest from the processor
DIMM slots that are white should be populated first
Do not mix Unbuffered memory (UDIMMs) with Registered memory (RDIMMs).
Do not install DIMMs if the corresponding processor is not installed
If only one processor is installed in a 2CPU system, only half of the DIMM slots are available
To maximize performance, balance the total memory capacity between all installed processors
It is not required, but it is recommended to load the channels similarly if possible
Populate DIMMs from heaviest load (quad-rank) to lightest load (single-rank) within a channel
Heaviest load (DIMM with most ranks) within a channel goes furthest from the processor
For memory mirroring mode, channel 3 must be unpopulated. Channels 1 and 2 are populated identically
For lock-step mode, channel 3 must be unpopulated. DIMMs in channels 1 and 2 will be installed in pairs. The paired
slots will be 1,4; 2,5 on the BL460c G6
Low Voltage DIMMs can only be used with Intel Xeon 5600 series processors.
If mixing DIMM voltage is a requirement, please note that the DIMMs will run at 1.5V since all 1.35V are capable of
supporting 1.5V operations
NOTES:
PC3-10600 DIMMs have a maximum speed of 1333MHz. PC3-8500 DIMMs have a maximum speed of 1066MHz.
Mixing DIMM speeds is allowed, but the system processor speed rules always override the DIMM capabilities
If you do mix DIMM speeds, the memory bus will default to the minimum clock rate of all DIMMs in the system - even if
the slower DIMM is on the other processor
If you install 1x 1066MHz DIMM in channel 1 and 1x 1333MHz DIMM in channel 2, the maximum speed will be
1066MHz
If you install 1x 1066MHz DIMM in channel 1 and 5x 1333MHz DIMMs with 1 DIMM Per Channel (DPC) in each of the
other channels, the maximum speed will be 1066MHz
Maximum memory speed will also depend on the processor installed
HP ProLiant WS460c G6 Workstation Blade DIMM slot and configuration diagrams
Basic memory slot and population diagram
Population order; start with "A" first, "B" second, "C" third, etc.
Chnl 1
slot #
1
2
12 DIMM SLOTS (6 per CPU node)
CPU1
CPU2
population order
slot #
population order
D
1
D
A
2
A
Chnl 1
Chnl 2
3
4
E
B
3
4
E
B
Chnl 2
Chnl 3
5
6
F
C
5
6
F
C
Chnl 3
DA - 13429 Worldwide QuickSpecs — Version 27 — 8.31.2012
Page 26
HP ProLiant WS460c Generation 6 (G6)
Workstation Blade
QuickSpecs
Memory
HP ProLiant WS460c G6 Server Blade (1P Model)
Standard memory configuration (1 CPU model)
2GB (2 x 1GB) of PC3-10600 (DDR3-1333) UDIMMs
or
4GB (4 x 1GB) of PC3-10600 (DDR3-1333) UDIMMs
slot #
Chnl 1
1
2
CPU1
population order
D: 1GB DIMM (if
4GB model)
A: 1GB DIMM
slot #
CPU2
population order
1
D: empty
2
A: empty
Chnl 1
Chnl 2
3
4
E: empty
B: 1GB DIMM
3
4
E: empty
B: empty
Chnl 2
Chnl 3
5
F: empty
C: 1GB DIMM (if
4GB model)
5
F: empty
Chnl 3
6
C: empty
6
Standard Memory Plus Optional Memory (1 CPU model)
10 GB of PC3-10600 (DDR3-1333) UDIMMs (2 x 1GB plus 4 x 2GB); (2GB memory standard model)
8GB of PC3-10600 (DDR3-1333) UDIMMs (4 x 1GB plus 2 x 2GB); (4GB memory standard model)
slot #
Chnl 1
1
2
CPU1
population order
D: 1GB DIMM (if
4GB model),
2GB DIMM (if 2GB
model)
A: 1GB DIMM
slot #
CPU2
population order
Chnl 1
1
D: empty
2
A: empty
Chnl 2
3
4
E: 2GB DIMM
B: 1GB DIMM
3
4
E: empty
B: empty
Chnl 2
Chnl 3
5
F: 2GB DIMM
C: 1GB DIMM (if
4GB model),
2GB DIMM (if 2GB
model)
5
F: empty
Chnl 3
6
C: empty
6
Standard Memory Replaced with Optional Memory (1 CPU model)
96GB of PC3-8500 Quad-Rank RDIMMs (6 x 16GB)
DA - 13429 Worldwide QuickSpecs — Version 27 — 8.31.2012
Page 27
HP ProLiant WS460c Generation 6 (G6)
Workstation Blade
QuickSpecs
Memory
Chnl 1
slot #
1
2
CPU1
population order
D: 16GB DIMM
A: 16GB DIMM
slot #
1
2
CPU2
population order
D: empty
A: empty
Chnl 1
Chnl 2
3
4
E: 16GB DIMM
B: 16GB DIMM
3
4
E: empty
B: empty
Chnl 2
Chnl 3
5
6
F: 16GB DIMM
C: 16GB DIMM
5
6
F: empty
C: empty
Chnl 3
UDIMM maximum configuration (1 CPU model)
24GB, consisting of six (6) 4GB dual-rank PC3-10600 UDIMMs
Chnl 1
slot #
1
2
CPU1
population order
D: 4GB DIMM
A: 4GB DIMM
slot #
1
2
CPU2
population order
D: empty
A: empty
Chnl 1
Chnl 2
3
4
E: 4GB DIMM
B: 4GB DIMM
3
4
E: empty
B: empty
Chnl 2
Chnl 3
5
6
F: 4GB DIMM
C: 4GB DIMM
5
6
F: empty
C: empty
Chnl 3
Standard Memory Replaced with Optional Memory (2 CPU Model)
RDIMM maximum configuration
192GB, consisting of twelve (12) 16GB quad-rank PC3-8500 RDIMMs
Chnl 1
slot #
1
2
CPU1
population order
D: 16GB DIMM
A: 16GB DIMM
slot #
1
2
CPU2
population order
D: 16GB DIMM
A: 16GB DIMM
Chnl 1
Chnl 2
3
4
E: 16GB DIMM
B: 16GB DIMM
3
4
E: 16GB DIMM
B: 16GB DIMM
Chnl 2
Chnl 3
5
6
F: 16GB DIMM
C: 16GB DIMM
5
6
F: 16GB DIMM
C: 16GB DIMM
Chnl 3
UDIMM maximum configuration (2 CPU model)
48GB, consisting of twelve (12) 4GB dual-rank PC3-10600 UDIMMs
DA - 13429 Worldwide QuickSpecs — Version 27 — 8.31.2012
Page 28
HP ProLiant WS460c Generation 6 (G6)
Workstation Blade
QuickSpecs
Memory
Chnl 1
slot #
1
2
CPU1
population order
D: 4GB DIMM
A: 4GB DIMM
slot #
1
2
CPU2
population order
D: 4GB DIMM
A: 4GB DIMM
Chnl 1
Chnl 2
3
4
E: 4GB DIMM
B: 4GB DIMM
3
4
E: 4GB DIMM
B: 4GB DIMM
Chnl 2
Chnl 3
5
6
F: 4GB DIMM
C: 4GB DIMM
5
6
F: 4GB DIMM
C: 4GB DIMM
Chnl 3
NOTE: Capacity references are rounded to the common Gigabyte values.
1GB = 1024MB
2GB = 2048MB
4GB = 4096MB
8GB = 8192MB
16GB = 16384MB
Following are memory options available from HP:
HP Memory
Registered DIMMs (RDIMMs)
HP 2GB (1x2GB) Dual Rank x8 PC3-10600 (DDR3-1333) Registered CAS-9
Memory Kit
HP 4GB (1x4GB) Dual Rank x4 PC3-10600 (DDR3-1333) Registered CAS-9
Memory Kit
HP 4GB (1x4GB) Single Rank x4 PC3-10600 (DDR3-1333) Registered CAS-9
Memory Kit
HP 4GB (1x4GB) Single Rank x4 PC3L-10600 (DDR3-1333) Registered CAS-9
Low Power Memory Kit
HP 8GB (1x8GB) Dual Rank x4 PC3-10600 (DDR3-1333) Registered CAS-9
Memory Kit
HP 8GB (1x8GB) Dual Rank x4 PC3L-10600 (DDR3-1333) Registered CAS-9
Low Power Memory Kit
HP 16GB (1x16GB) Quad Rank x4 PC3-8500 (DDR3-1066) Registered CAS-7
Memory Kit
Unbuffered with ECC DIMMs (UDIMMs)
HP 1GB (1x1GB) Single Rank x8 PC3-10600 (DDR3-1333) Unbuffered CAS-9
Memory Kit
HP 2GB (1x2GB) Dual Rank x8 PC3-10600 (DDR3-1333) Unbuffered CAS-9
Memory Kit
HP 4GB (1x4GB) Dual Rank x8 PC3-10600 (DDR3-1333) Unbuffered CAS-9
Memory Kit
NOTE: All DDR3 memory option kits consist of one DIMM per kit. For detailed
memory configuration rules and guidelines, please use the Online DDR3
Memory Configuration Tool: www.hp.com/go/ddr3memory-configurator.
DA - 13429 Worldwide QuickSpecs — Version 27 — 8.31.2012
500656-B21
500658-B21
593339-B21
604504-B21
500662-B21
604506-B21
500666-B21
500668-B21
500670-B21
500672-B21
Page 29
QuickSpecs
HP ProLiant WS460c Generation 6 (G6)
Workstation Blade
Storage
1-2
2 x SFF SAS Hot Plug Hard Drives
Hard Drives
NOTE: The components of a storage subsystem (e.g. the drive, the HBA/controller, firmware, and the server backplane)
should operate at the same data transfer rate or the system bandwidth will be negotiated down to an acceptable level for all
components.
SAS Hot Plug SFF (2.5-inch) Enterprise (ENT) Drives
Quantity
Position
Supported
Supported Controller
900GB 6G SAS 10K
2
1-2
HP Smart Array P410i Controller
600GB 6G SAS 10K
450GB 6G SAS 10K
300GB 6G SAS 15K
300GB 6G SAS 10K
146GB 6G SAS 15K
SAS Hot Plug SFF (2.5-inch) Midline (MDL) Drives
Quantity
Position
Supported
Supported
1TB 6G SAS 7.2K
2
1-2
500GB 6G SAS 7.2K
Controller
HP Smart Array P410i Controller
6G SAS Hot Plug Enterprise Performance Solid State Drives
Quantity
Position
Supported
Supported Controller
400GB 6G SAS SLC
Up to 8
1-8
HP Smart Array P410i Controller
200GB 6G SAS SLC
6G SAS Hot Plug Enterprise Mainstream Solid State Drives
Quantity
Position
Supported
Supported Controller
800GB 6G SAS MLC
Up to 8
1-8
HP Smart Array P410i Controller
400GB 6G SAS MLC
200GB 6G SAS MLC
SATA Hot Plug SFF (2.5-inch) Midline (MDL) Drives
Quantity
Position
Supported
Supported
1TB 3G SATA 7.2K
Up to 8
1-8
500GB 3G SATA 7.2K
Controller
HP Smart Array P410i Controller
DA - 13429 Worldwide QuickSpecs — Version 27 — 8.31.2012
Page 30
QuickSpecs
HP ProLiant WS460c Generation 6 (G6)
Workstation Blade
Storage
SATA Hot Plug 2.5" Enterprise Mainstream Solid State Drives
Quantity
Position
Supported
Supported Controller
400GB 3G SATA MLC
Up to 8
1-8
HP Smart Array P410i Controller
200GB 3G SATA MLC
100GB 3G SATA MLC
DA - 13429 Worldwide QuickSpecs — Version 27 — 8.31.2012
Page 31
QuickSpecs
HP ProLiant WS460c Generation 6 (G6)
Workstation Blade
Technical Specifications
System Unit
Dimensions (H x W x D) 7.154 x 2.19 x 20.058 in (18.17 x 5.56 x 50.95 cm)
(with bezel)
Weight
Maximum
14.20 lb (6.44 kg)
(approximate)
(all hard drives and
processors installed)
Minimum
10.75 lb (4.87 kg)
(one hard drive and
processor installed)
Power Specifications For power specifications including Input Requirements, BTU Rating, and
Power Supply Output, please see the HP BladeSystem c-Class
Enclosures QuickSpecs located at URL:
HP BladeSystem c3000 Enclosure QuickSpecs:
http://h18000.www1.hp.com/products/quickspecs/12790_div/
12790_div.html
HP BladeSystem c7000 Enclosure QuickSpecs:
http://h18000.www1.hp.com/products/quickspecs/12810_div/
12810_div.html
System Inlet
Temperature
Relative Humidity
(non-condensing)
Altitude
Acoustic Noise
To review typical system power ratings use the HP BladeSystem Power
Sizer which is available via the online tool located at URL:
http://www.hp.com/go/bladesystem/powercalculator
Operating
10° to 35°C (50° to 95°F) at sea level with an
altitude derating of 1.0°C per every 305 m
(1.8°F per every 1000 ft) above sea level to a
maximum of 3050 m (10,000 ft), no direct
sustained sunlight. Maximum rate of change
is 10°C/hr (18°F/hr). The upper limit may be
limited by the type and number of options
installed.
System performance may be reduced if
operating with a fan fault or above 30°C
(86°F).
Non-operating
-30° to 60°C (-22° to 140°F). Maximum rate of
change is 20°C/hr (36°F/hr).
Operating
10 to 90% relative humidity (Rh), 28°C
(82.4°F) maximum wet bulb temperature, noncondensing.
Non-operating
5 to 95% relative humidity (Rh), 38.7°C
(101.7°F) maximum wet bulb temperature,
non-condensing.
Operating
3050 m (10,000 ft). This value may be limited
by the type and number of options installed.
Maximum allowable altitude change rate is
457 m/min (1500 ft/min).
Non-operating
9144 m (30,000 ft). Maximum allowable
altitude change rate is 457 m/min (1500
ft/min).
For acoustic noise specifications, please see the HP BladeSystem cClass Enclosures QuickSpecs located at URL:
HP BladeSystem c3000 Enclosure QuickSpecs:
http://h18000.www1.hp.com/products/quickspecs/12790_div/
12790_div.html
HP BladeSystem c7000 Enclosure QuickSpecs:
DA - 13429 Worldwide QuickSpecs — Version 27 — 8.31.2012
Page 32
QuickSpecs
HP ProLiant WS460c Generation 6 (G6)
Workstation Blade
Technical Specifications
http://h18000.www1.hp.com/products/quickspecs/12810_div/
12810_div.html
HP Smart Array P410i Disk Drive Interface
Controller
Server Interface
Cache Memory
3Gb (6Gb Capable) SAS (Serial Attached SCSI)
1.5Gb (3Gb Capable) SATA (Serial Advanced Technology Attachment)
x4 PCI Express host interface
0 MB (none) standard
Optional 256MB or 512MB Cache Memory
2 (with standard 0MB cache)
Logical Drives
Supported
Maximum Logical Drive32 (with optional 256MB cache)
Capacity
64 (with optional 512MB cache)
Host Memory
64-bit, supporting servers memory space greater than 4 GB
Addressing
RAID Support
RAID 1( Mirroring)
RAID 0 (Striping)
Upgradeable Firmware Controller: Upgradeable Firmware with Recovery ROM feature
Online Drive Flash (with SAS drives) requires 256MB or 512MB module
Embedded NC532i Dual Type
Port Flex-10 10GbE
Network Processor
Multifunction Server
Data Transfer Method
Adapter
Network Transfer Rate
IEEE Compliance
Integrated dual-port KR 10GbE
Broadcom 57711
x4 PCI Express Generation 2
Two ports, each at 20 Gbps full duplex; 40 Gbps aggregate full duplex
theoretical bandwidth
NOTE: Each port is autosensing 1 Gb / 10 Gb, and can interoperate
with 1 Gb HP BladeSystem c-Class interconnect components.
NOTE: Each port on the NC532i adapter transmits from the server at
only 20 Gbps (theoretical) full duplex.
802.1p, 802.1q, 802.3u, 802.3ad, 802.3ae, 802.3ap (10GBase-KX4),
802.3x and 802.3z
GPU Capacity Planning GPU Capacity PlanningEach virtual machine will have an amount of the VRAM reserved from
for VDI with RemoteFX
the GPU in the server. The reservation is taken from the server GPU's
dedicated VRAM. The amount of VRAM reserved for a given virtual
machine is based on the number of monitors and their resolutions,
shown in the table below
Maximum
Maximum Number of Monitors in Virtual Machine
resolution
Setting
1 Monitor
2 Monitors
3 Monitors
4 Monitors
1024x768
75MB
10MB
135MB
165MB
1280x1024
125MB
175MB
225MB
275MB
1600x1200
184MB
257MB
330MB
1900x1200
220MB
308MB
DA - 13429 Worldwide QuickSpecs — Version 27 — 8.31.2012
Page 33
QuickSpecs
HP ProLiant WS460c Generation 6 (G6)
Workstation Blade
Technical Specifications
NVIDIA Quadro
FX 880M graphics
adapter
Memory size
Memory type
Memory interface
Card type
I/O interface
1 GB
GDDR-3
128-bit
MXM-v.3.0
PCIe (x16);
NOTE: HP WS460c G6 I/O slot is PCIe x8
35W (1GB)
Max power
consumption
API
DirectX 10.1, Shader Model 4.0; OpenGL3.2
Upgradeable Firmware Upgradeable Firmware
Server Operating
Microsoft® Windows Server 2008 R2 SP1 (64-bit) Standard, Enterprise
Systems
and DataCenter editions
Client Operating
Genuine Microsoft® Windows 7.0® Business (32-bit and 64-bit
Systems
Microsoft Windows Vista Business SP2 (32-bit & 64-bit)
Microsoft Windows XP Professional SP3 (32-bit)
Microsoft Windows XP Professional x64 edition with SP2
Red Hat Enterprise Linux (RHEL) 4.8 and 5.3 (64-bit only)
NVIDIA Quadro
FX 2800M graphics
adapter
Memory size
Memory type
Memory interface
Card type
I/O interface
1 GB
GDDR-3
256-bit
MXM-v.3.0
PCIe (x16);
NOTE: HP WS460c G6 I/O slot is PCIe x8
75W
Max power
consumption
API
DirectX 10.1, Shader Model 4.0; OpenGL3.2
Upgradeable Firmware Upgradeable Firmware
Server Operating
Microsoft® Windows Server 2008 R2 SP1 (64-bit) Standard, Enterprise
Systems
and DataCenter editions
Client Operating
Genuine Microsoft® Windows 7.0® Business (32-bit and 64-bit
Systems
Microsoft Windows Vista Business SP2 (32-bit & 64-bit)
Microsoft Windows XP Professional SP3 (32-bit)
Microsoft Windows XP Professional x64 edition with SP2
Red Hat Enterprise Linux (RHEL) 4.8 and 5.3 (64-bit only)
DA - 13429 Worldwide QuickSpecs — Version 27 — 8.31.2012
Page 34
HP ProLiant WS460c Generation 6 (G6)
Workstation Blade
QuickSpecs
Technical Specifications
NVIDIA Quadro
FX 4000 graphics
adapter
Memory size
Memory type
Memory interface
I/O interface
Max power
consumption
API
Server Operating
Systems
Client Operating
Systems
NVIDIA Quadro
5000 graphics
adapter
DirectX 10.1, Shader Model 4.0; OpenGL3.3
Microsoft® Windows Server 2008 R2 SP1 (64-bit) Standard, Enterprise
and DataCenter editions
Citrix XenServer 6 Enterprise and Platinum editions
Genuine Microsoft® Windows 7.0® Business (32-bit and 64-bit
Microsoft Windows Vista Business SP2 (32-bit & 64-bit)
Microsoft Windows XP Professional SP3 (32-bit)
Microsoft Windows XP Professional x64 edition with SP2
Red Hat Enterprise Linux (RHEL) 4.8 and 5.3 (64-bit only)
Memory size
2.5 GB
Memory type
Memory interface
I/O interface
Max power
consumption
API
Server Operating
Systems
GDDR-5
320-bit
PCIe (x16) Gen 2
152W
Client Operating
Systems
NVIDIA Quadro
6000 graphics
adapter
2GB
GDDR-5
256-bit
PCIe (x16) Gen 2
142W
Memory size
Memory type
Memory interface
I/O interface
Max power
consumption
API
Server Operating
Systems
Client Operating
Systems
DirectX 11, Shader Model 5.0; OpenGL4.1
Microsoft® Windows Server 2008 R2 SP1 (64-bit) Standard, Enterprise
and DataCenter editions
Citrix XenServer 6 Enterprise and Platinum Edition
Genuine Microsoft® Windows 7.0® Business (32-bit and 64-bit
Microsoft Windows Vista Business SP2 (32-bit & 64-bit)
Microsoft Windows XP Professional SP3 (32-bit)
Microsoft Windows XP Professional x64 edition with SP2
Red Hat Enterprise Linux (RHEL) 4.8 and 5.3 (64-bit only)
6.0 GB
GDDR-5
384-bit
PCIe (x16) Gen 2
225W
DirectX 11, Shader Model 5.0; OpenGL4.1
Microsoft® Windows Server 2008 R2 SP1 (64-bit) Standard, Enterprise
and DataCenter editions
Citrix XenServer 6 Enterprise and Platinum Edition
Genuine Microsoft® Windows 7.0® Business (32-bit and 64-bit
Microsoft Windows Vista Business SP2 (32-bit & 64-bit)
Microsoft Windows XP Professional SP3 (32-bit)
Microsoft Windows XP Professional x64 edition with SP2
Red Hat Enterprise Linux (RHEL) 4.8 and 5.3 (64-bit only)
DA - 13429 Worldwide QuickSpecs — Version 27 — 8.31.2012
Page 35
HP ProLiant WS460c Generation 6 (G6)
Workstation Blade
QuickSpecs
Technical Specifications
AMD Firestream
FS9350 Compute
Accelerator
NVIDIA Tesla M2070Q
6GB Module
Environment-friendly
Products and
Approach
Memory size
Memory type
Stream Cores
I/O interface
Max power
consumption
Supported Operating
Systems
2.0 GB
GDDR-5
1440
PCIe (x16) Gen 2
175W
Memory size
Memory type
Memory interface
I/O interface
Max power
consumption
Supported Operating
Systems
6.0 GB
GDDR-5
384-bit
PCIe (x16) Gen 2
225W
End-of-life
Management and
Recycling
Hewlett-Packard offers end-of-life HP product return, trade-in, and
recycling programs in many geographic areas. For trade-in information,
please go to: http://www.hp.com/go/green. To recycle your product,
please go to: http://www.hp.com/go/green or contact your nearest HP
sales office. Products returned to HP will be recycled, recovered or
disposed of in a responsible manner.
RHEL 5
RHEL 5
SLES 11
Windows Server 2008
The EU WEEE directive (2002/95/EC) requires manufacturers to
provide treatment information for each product type for use by treatment
facilities. This information (product disassembly instructions) is posted
on the Hewlett Packard web site at: http://www.hp.com/go/green. These
instructions may be used by recyclers and other WEEE treatment
facilities as well as HP OEM customers who integrate and re-sell HP
equipment.
© Copyright 2012 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice.
Microsoft and Windows NT are US registered trademarks of Microsoft Corporation. Intel, the Intel logo, Xeon and Xeon
Inside are trademarks of Intel Corporation in the U.S. and other countries.
The only warranties for HP products and services are set forth in the express warranty statements accompanying such
products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for
technical or editorial errors or omissions contained herein.
For hard drives, 1GB = 1 billion bytes. Actual formatted capacity is less.
DA - 13429 Worldwide QuickSpecs — Version 27 — 8.31.2012
Page 36
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising