SNC-WR602
(Project No.)
(Date)
(Project Name)
(Project Location)
ARCHITECT & ENGINEER SPECIFICATIONS
SECTION 28 23 29
VIDEO SURVEILLANCE REMOTE DEVICES AND SENSORS
SNC-WR602
Outdoor Unitized High Definition (HD)
Rapid Dome Network Camera
Powered by IPELA ENGINE PRO
(Software version 2.1.0 or later)
PART 2 – PRODUCTS
2.01 NETWORK CAMERA SPECIFICATIONS
Table of Contents
A. MAIN FEATURES........................................................................................ 2
B. CAMERA ..................................................................................................... 7
C. CAMERA FEATURES ................................................................................. 9
D. VIDEO ....................................................................................................... 14
E. INTELLIGENT VIDEO ANALYTICS........................................................... 18
F. AUDIO ....................................................................................................... 20
G. SYSTEM REQUIREMENTS & NETWORK ............................................... 21
H. INETERFACES.......................................................................................... 24
I. GENERAL SPECIFICATIONS ................................................................... 26
J. REGULATORY SPECIFICATIONS ........................................................... 28
K. SUPPLIED ACCESSORIES ...................................................................... 29
L. OPTIONAL ACCESSORIES ...................................................................... 30
M. DIMENSIONS ............................................................................................ 31
VIDEO SURVEILLANCE REMOTE DEVICES AND SENSORS
28 23 29 - 1
ARCHITECT & ENGINEER SPECIFICATIONS
SNC-WR602
A. MAIN FEATURES:
1.
Outdoor Unitized High Definition (HD) Rapid Dome Network
Camera
2. 720p HD picture quality (1280 x 720 pixels maximum resolution),
supporting H.264 at 60 fps (IP)
3. Powerful 30X optical zoom capability
4. High frame rate of 60 frames per second (fps) to provide smoother
and less blurry moving pictures
5. Wide Dynamic range (Wide-D) equivalent to 130 dB
6. Industry-leading levels of panning performance with a pan speed of
700°/s
7. Gyroscopic Image Stabilizer:
The Gyroscopic Image Stabilizer shall minimize the effect of
camera shake or vibration, reducing any image blur. Thanks to an
advanced gyroscopic technology, this stabilizer is capable of
detecting blurred images precisely and compensating for them
effectively. This provides better performance than any image
stabilizer on the market that uses conventional motion-vectorbased technology.
8. Focal Plane Distortion Correction technology:
The Focal Plane Distortion Correction technology shall correct any
image distortion generated in a scene by the CMOS sensor focal
plane phenomenon
9. Defog Image Processing feature:
The Defog Image Processing feature shall be capable of clearing
up fog, mist, and haze in a scene to achieve more visible images.
10. Simultaneously encoding up to 3 of the following streams in any
combination, including multiple instances of the same compression
format: JPEG and/or H.264 (High/Main/Baseline Profile)
11. AAC (16, 48 kHz)/G.726 (40, 32, 24, 16 kbps)/G.711 (64 kbps)
audio compression formats
12. Minimum scene illumination of 1.0 lx in Color mode and 0.03 lx in
Black and White (B/W) mode (50 IRE [IP], F 1.6, View-DR Off, VE
Off, Auto Gain Control maximum rate MAX, 1/30s, 30fps).
VIDEO SURVEILLANCE REMOTE DEVICES AND SENSORS
28 23 29 - 2
ARCHITECT & ENGINEER SPECIFICATIONS
SNC-WR602
13. Picture mode:
Picture mode shall be selectable from a range of camera scenes in
the setting menu to optimize picture quality in various applications.
This mode has the following options;
- “Standard”
- “Situation Priority - Moving object” to stabilize images
- “Situation Priority - Low noise” to reducing noise on images,
especially dark scenes
- “Flickerless” to reduce the flicker on images according to power
frequency (50 Hz or 60 Hz) of the lighting
14. Variable bit rate (VBR) capable of maximum bit rate setting:
The camera shall have 2 bit rate compression modes, variable bit
rate (VBR) or constant bit rate (CBR) compression, selectable to
correspond with various network conditions.
When VBR is selected, higher quality images shall be always
maintained regardless of the bandwidth and storage capacity
requirements, because the bit rate shall be variable by a scene.
Besides, in VBR mode, the camera shall limit the "Maximum value
of the bit rate", while maintaining the image quality and the frame
rate, so as to reduce the storage capacity.
Moreover in VBR mode with the "Maximum bit rate limit", the
camera shall accept the frame skip for the bit rate control to
minimize the storage capacity.
On the other hand, when CBR is selected, the bandwidth and
storage capacity requirements shall be calculated easily, because
the bit rate shall be always constant.
15. IP66-rated waterproof and dust-tight feature:
The camera shall be IP66 rated in accordance with the IEC 605292
standard for outdoor surveillance, or indoor where water ingress
may pose an issue.
16. IK10-rated vandal-resistant feature:
The camera shall be IK10 rated in accordance with the IEC 62262
standard to vandal-resistant feature for protecting the camera from
destructive behaviors.
17. IPELA ENGINE PRO:
Integrated signal processing system for high picture quality shall
combine unique signal processing and video analytics technologies.
This signal processing system provides four unique features such
as high frame rate, View-DR, XDNR, DEPA Advanced, Gyroscopic
Image Stabilizer, Focal Plane Distortion Correction, and
Defog Image Processing
VIDEO SURVEILLANCE REMOTE DEVICES AND SENSORS
28 23 29 - 3
ARCHITECT & ENGINEER SPECIFICATIONS
SNC-WR602
18. Visibility enhanced wide Dynamic Range (View-DR) :
This technology shall be a combination of unique full-capture Wide
Dynamic range (Wide-D) technology, the high-speed Exmor CMOS
sensor, and Visibility Enhancer (VE) technology.
The full-capture wide dynamic range technology shall use an
electronic shutter to capture multiple images and reproduce each
frame.
One image is taken using a standard exposure time and either 1 or
3 additional images are taken using very short exposure times,
depending on the camera type*.
(*This model shall synthesize a single image from 2 or 4 images
taken by slow shutter speed.)
With the advanced View-DR algorithm, all of the electrons
converted from the captured light are fully used by the imager,
which is significantly different from some other Wide-D
technologies in the industry which discard approximately half of
these electrons.
As a result, View-DR nearly doubles the sensitivity that is offered
by conventional Wide-D technologies.
The level of the wide dynamic range (View-DR) setting changes
automatically depending on lighting condition.
When the light level drops, the wide dynamic range (View-DR)
turns off automatically.
VIDEO SURVEILLANCE REMOTE DEVICES AND SENSORS
28 23 29 - 4
ARCHITECT & ENGINEER SPECIFICATIONS
SNC-WR602
19. Exmor CMOS:
This sensor shall realize high quality and low noise images.
20. Visibility Enhancer (VE):
This technology optimizes the brightness and color reproduction of
an image dynamically on a pixel-by-pixel basis while continuously
adapting to the scene. This method differs from the technique of
using the preset gamma curves.
Technically, this technology stretches the contrast in both the
backlit portions and the shadows within the given dynamic range,
which is different from unique wide dynamic range technologies.
This technology also contributes to the high sensitivity of the
camera.
By combining this technology with a unique noise reduction feature
named eXcellent Dynamic Noise Reduction (XDNR), the camera
can reproduce clear and bright images in very low-light conditions,
while keeping noise at a minimal level.
21. eXcellent Dynamic Noise Reduction (XDNR):
This technology reduces Auto Gain Control (AGC) noise to provide
clear images without motion blur. This also reduces image data
size.
22. XDNR and VE can be used in conjunction with each other and
shall provide approximately 4 times the sensitivity compared to the
condition where both features are set to off.
23. Intelligent Motion Detection (IMD):
This feature shall be able to minimize the number of false alarms
by eliminating environmental noise such as trees moving, ripples in
water, reflection from wet roads and gain noise to name but a few.
This is very different to other manufacturers that typically compare
just two frames together. This camera compares 15 frames
together, which ensures that only ambiguous objects moving can
trigger a real alarm.
As a result, this enables end users to focus on real events, not
suffer from loss of attention and quickly locate video that has been
recorded upon alarm activations.
24. Distributed Enhanced Processing Architecture Advanced (DEPA
Advanced):
This technology shall extend the benefits of unique conventional
intelligent video analytics and enables its functionality to be used
with third-party software vendors. Alternatively the camera can be
configured using the web interface to be a stand-alone intelligent
surveillance solution.
This means that end users get the same features as conventional
intelligent video analytics running at the edge without needing to
VIDEO SURVEILLANCE REMOTE DEVICES AND SENSORS
28 23 29 - 5
ARCHITECT & ENGINEER SPECIFICATIONS
SNC-WR602
have any recording solution. Alarms can be activated by the
camera, video can be recorded to a built-in SD/SDHC card, and
lights and alarms can be activated.
25. The camera shall be compliant with the Open Network Video
Interface Forum Profile S (ONVIF Profile S) conformance.
The camera shall also support ONVIF event commands such as
Tampering alarm, Motion alarm and Fan error.
VIDEO SURVEILLANCE REMOTE DEVICES AND SENSORS
28 23 29 - 6
ARCHITECT & ENGINEER SPECIFICATIONS
SNC-WR602
B. CAMERA:
1. The camera shall utilize a 1/3-type progressive scan Exmor CMOS
sensor.
2. The number of effective pixels shall be approx. 1.37 Megapixels.
3. The analog video output of the camera shall be selectable from
either the NTSC or PAL standards.
4. Camera synchronization shall be Internal.
5. The camera shall require a minimum scene illumination of:
Color:
1.0 lx (50 IRE [IP], F 1.6, View-DR Off, VE Off, Auto gain control
maximum rate MAX, 1/30s, 30 fps)
0.4 lx (30 IRE [IP], F 1.6, View-DR Off, VE Off, Auto gain control
maximum rate MAX, 1/30s, 30 fps)
B/W:
0.03 lx (50 IRE [IP], F 1.6, View-DR Off)
0.01 lx (30 IRE [IP], F 1.6, View-DR Off)
6. The camera shall have an equivalent 130 dB wide dynamic range
capability.
7. The video signal-to-noise ratio shall be more than 50 dB (Auto gain
control maximum rate 0 dB).
8. The camera shall limit the maximum amount of gain-controlled
automatically (AGC). Also, gain control shall be selected from -3
dB to +28 dB manually.
9. The electronic shutter speed shall be set from 1 to 1/10,000
second.
10. The exposure shall be selected among Full auto, Shutter priority,
Iris priority, or Manual when the unique wide dynamic range
function is not used.
The shutter speed is limited between 1/30 and 1/4 second for
NTSC, or between 1/25 and1/3 second for PAL when the Full auto
is selected. But it is selectable between 1 to 1/10,000 second
when the Shutter priority or Manual is selected.
11. White balance shall be selected among ATW (approx. 2000 K to
10000 K), ATW-PRO (approx. 2500 K to 6000 K), Indoor, Outdoor,
Fluorescent lamp, Mercury lamp, Sodium Vapor lamp, Metal Halide
VIDEO SURVEILLANCE REMOTE DEVICES AND SENSORS
28 23 29 - 7
ARCHITECT & ENGINEER SPECIFICATIONS
SNC-WR602
lamp, White LED, One push WB, or Manual settings.
The R/B gain offset can be set for the ATW or ATW-PRO settings.
12. The camera shall have an integrated 30X auto-focus powered
zoom lens.
13. The camera shall have 12X digital zoom capability.
14. The camera shall have the total zoom ratio of 360X with 30X
optical zoom and 12X digital zoom capabilities.
15. The camera shall have a Powered Focus adjustment capability via
the GUI.
Focus mode shall be selected among Auto or Manual (Near, Far,
or One Push Focus). Also, focus near limit shall be set for the
range at which to automatically focus.
16. The camera shall be capable of 360˚ endless pan rotation and a tilt
range of 220˚ with auto invert function, designed for ceiling mount
operation.
The camera shall also have maximum pan/tilt speeds of 700˚ per
second.
17. The viewing angle shall be:
Horizontal: 58.3 ˚ to 2.1 ˚.
Vertical: 34.8 ˚ to 1.2 ˚.
18. The focal length shall be 4.3 to 129.0 mm.
19. The aperture range for the lens (F number) shall be F 1.6 (Wide) to
F 4.7 (Tele).
20. The minimum object distance shall be 11 7/8 inches (300 mm).
21. The camera shall be capable of guard tour (position tour), for which
up to 16 presets can be programmed, and moves to each preset
sequentially when guard tour is activated. Up to 5 tours can be set.
The camera shall also have 256 user defined presets, with a
repeatable mechanical preset accuracy of ± 0.15˚ (typical).
VIDEO SURVEILLANCE REMOTE DEVICES AND SENSORS
28 23 29 - 8
ARCHITECT & ENGINEER SPECIFICATIONS
SNC-WR602
C. CAMERA FEATURES:
1. The camera shall have a True Day/Night (D/N) function to switch to
Day mode (color mode) or Night mode (black and white mode)
depending on the light level.
2. The camera shall display the "Panorama Image" which is a still
picture converted from the image taken when the user was going
to create it with SNC
toolbox.
Also, the camera shall have 2 display formats for the “Panorama
Image”: Map view and Arctic view.
3. The camera shall have an auto-flip function.
When the camera tilts downward to the point where it faces the
ground, it can automatically switch the tilt movement of the camera
downward to upward so that the displayed picture is reversed.
4. The camera shall have an Image Stabilizer function, which can
display with less video sway when the camera is installed in a
place with vibration.
VIDEO SURVEILLANCE REMOTE DEVICES AND SENSORS
28 23 29 - 9
ARCHITECT & ENGINEER SPECIFICATIONS
SNC-WR602
5. The camera shall have polygonal privacy zone masking which
blocks out unwanted or prohibited area within the video image to
protect privacy.
Mask colors shall be Black, any of 6 shades of Gray, White, Green,
Yellow, Red, Cyan, Magenta, and Blue.
Mosaic patters shall be also selected as masking.
The camera shall be capable of masking up to 12 areas.
Such capability shall be via vendor supplied SNC toolbox utility
software or the browser-based setup menu.
6. The pre-/post-alarm recording capabilities using an „Edge Storage‟
function shall be as follows:
- Capable of storing several seconds of pre-alarm and post-alarm
images when an alarm is triggered by the motion detection, VMFs,
camera tampering detection, audio detection or sensor input.
- Capable of recording image and sound files on the approx. 8 MB
of built-in memory or SD memory card (not supplied), or
transferring the files to an FTP server.
- Record in the compression format selected for monitoring.
- Correspond to a still image as a snapshot in the event.
- Have a maximum duration for pre- and post-alarm recording that
shall be dependent on the bit rate setting for H.264
(High/Main/Baseline Profile or the picture quality and frame rate
setting for JPEG as shown in the following tables:
For H.264
VIDEO SURVEILLANCE REMOTE DEVICES AND SENSORS
28 23 29 - 10
ARCHITECT & ENGINEER SPECIFICATIONS
SNC-WR602
For JPEG
7. The „Edge Storage‟ function shall operate as follows:
- Capable of storing up to 900 seconds of pre-alarm and up to
7200 seconds of post-alarm images and audio on a SD memory
card.
- Record in the compression format selected for monitoring.
- Recording to this storage area can be done manually or when an
alarm is triggered.
- The trigger can be based on motion detection, VMFs, camera
tampering detection, audio detection, sensor input or network
disconnection, or a combination of those alarms using Boolean
operands such as a logical „AND‟, ‟OR‟, or „THEN‟.
- Capable of streaming the recorded moving image data using the
same protocols as live streaming such as RTP/RTCP, RTSP over
TCP, RTSP over HTTP, so that the user can view recorded image
while recording.
- Capable of streaming the recorded still image data using the
HTTP protocol.
- Capable of simultaneously streaming live video with recorded
video by using different sessions.
- Capable of downloading the recorded video at a variety of speed
rates such as 0.5x and 2x speed.
- Capable of setting periodical recording, alarm record schedule,
and overwriting record for the still image data.
VIDEO SURVEILLANCE REMOTE DEVICES AND SENSORS
28 23 29 - 11
ARCHITECT & ENGINEER SPECIFICATIONS
SNC-WR602
8. The camera shall have an internal memory size of approx. 40 MB
for buffering.
9. The camera shall be capable of pre- and post-alarm buffering.
10. The camera shall support the voice alert function, which can
automatically play an audio file stored on the camera by an alarm
trigger using motion detection, unique Video Motion Filters (DEPA
Advanced VMFs), camera tampering detection, or via a sensor
input.
11. The camera shall be IK10 rated in accordance with the IEC 62262
standard to vandal-resistant feature for protecting the camera from
destructive behaviors.
12. The camera shall be IP66 rated in accordance with the IEC 60529
standard to have waterproof and dust-tight feature for outdoor
surveillance, or indoor where water ingress may pose an issue.
13. The camera shall have the capability to display a wide variety of
overlays in any of 7 positions on the video image (4 corners, top,
bottom, or center of the image).
The following overlays shall be possible:
- Camera ID of up to 20 alphanumeric characters or a logo in gif
format
- Date/Time data with selectable formats such as yyyy mm dd
hh:mm:ss, mm dd yyyy hh:mm:ss, and dd mm yyyy hh:mm:ss
- User setting frame rate (fps) and bit rate (bps)
- Event -- sensor IN, unique intelligent motion detection, unique
video motion filters, camera tampering detection
- Character string
- Compression format information
The following display styles shall be available: outline and
transparent, white half-transparent, black half-transparent, white,
and black backgrounds. Unique intelligent motion detection shall
not be effective in the selected superimposed areas.
The following font colors are available: Black, Blue, Red, Magenta,
Green, Cyan, Yellow and White.
All of overlays except the Date/Time data can be set to blink.
VIDEO SURVEILLANCE REMOTE DEVICES AND SENSORS
28 23 29 - 12
ARCHITECT & ENGINEER SPECIFICATIONS
SNC-WR602
14. The camera web browser shall support the following languages:
English, Japanese, French, Spanish, German, Italian, Simplified
Chinese, Traditional Chinese, Korean, Portuguese, Russian, Hindi,
Arabic, Vietnamese, and Thai.
15. The camera shall have a Smartphone viewer, which can display
the camera image and operate Pan/Tilt/Zoom (PTZ) on the
smartphone.
VIDEO SURVEILLANCE REMOTE DEVICES AND SENSORS
28 23 29 - 13
ARCHITECT & ENGINEER SPECIFICATIONS
SNC-WR602
D. VIDEO:
1. The supported resolutions shall be 1280 x 720, 1024 x 576, 720 x
576 (PAL), 720 x 480 (NTSC), 704 x 576, 640 x 480, 640 x 360,
352 x 288, and 320 x 184 resolution.
2. The supported resolutions are shown in the following:
3. The camera shall support the following compression formats:
JPEG and H.264 (High/Main/Baseline Profile).
4. The maximum resolution for each compression format shall be
1280 x 720.
5. The camera is compliant with the SMPTE 296M in terms of number
of pixels (1280 x 720) and 16:9 format.
6. The maximum frame rate shall be 60 frames per second in H.264
(High/Main/ Baseline Profile) and JPEG at 1280 x 720 resolution.
7. The camera shall provide smoother and less blurry moving pictures
with the High Frame Rate of 50 fps (PAL) or 60 fps (NTSC).
When the High Frame Rate setting is set to off, the maximum
frame rate shall be 25 fps (PAL) or 30 fps (NTSC).
8. Frame rate (fps) shall be selected among;
For NTSC (60Hz) mode: 1, 2, 3, 4, 5, 6, 8, 10, 12, 15, 20, 30, or
60*.
For PAL (50Hz) mode: 1, 2, 3, 4, 5, 6, 8, 10, 12, 16, 20, 25, or 50*.
*Valid only when the High Frame rate mode is set to „ON‟.
9. The camera shall have constant bit rate (CBR) or variable bit rate
(VBR) capable of maximum bit rate setting compression mode
selectable to correspond with various network conditions.
When CBR is selected, the bandwidth and storage capacity
requirements shall be calculated easily, because the bit rate shall
be always constant. On the other hand, image quality shall
VIDEO SURVEILLANCE REMOTE DEVICES AND SENSORS
28 23 29 - 14
ARCHITECT & ENGINEER SPECIFICATIONS
SNC-WR602
degrade exhibiting signs of macro blocking depending on the
scene situation.
When VBR is selected, higher quality images shall be always
maintained regardless of the bandwidth and storage capacity
requirements, because the bit rate shall be variable by a scene.
Besides, in VBR mode, the camera shall limit the "Maximum value
of the bit rate", while maintaining the image quality and the frame
rate, so as to reduce the storage capacity.
Moreover in VBR mode with the "Maximum bit rate limit", the
camera shall accept the frame skip for the bit rate control to
minimize the storage capacity.
10. Bit rate (Kbps) shall be selected among 64, 128, 256, 384, 512,
768, 1000, 1500, 2000, 3000, 4000, 5000, 6000, 7000, 8000,
16000, 24000, or 32000.
11. The camera shall be capable of electronic pan/tilt/zoom or e-PTZ
during e-PTZ mode.
12. The camera shall have an Adaptive Rate Control (ARC) function
when using H.264 (High/Main/Baseline Profile) compression.
This function when enabled, shall allow the camera to maintain the
frame rate at a reduced image quality when network congestion
occurs. Should network bandwidth become further restricted, the
frame rate shall then drop automatically to a suitable speed to
maintain image integrity.
13. The camera shall be capable of limiting the bandwidth from 64
kbps to 32 Mbps in H.264 (High/Main/Baseline Profile), and from
0.5 Mbps to an unlimited bandwidth in JPEG.
14. JPEG compression levels shall be user selectable in 10 levels of
compression ratios, based on an image of 24 bits per picture
element (8 bits each for YUV).
15. Constant bit rate algorithm for JPEG data:
The camera shall be capable of equalizing JPEG data sizes to
have stable bandwidth utilization. Data size for each compression
level is as follows:
VIDEO SURVEILLANCE REMOTE DEVICES AND SENSORS
28 23 29 - 15
ARCHITECT & ENGINEER SPECIFICATIONS
SNC-WR602
16. Actual frame rate in JPEG shall be shown in the following table:
17. The camera shall have the capability of simultaneously encoding
up to 3 of the following compression formats in any combination,
including multiple streams of the same format: JPEG and H.264
(High/Main/Baseline Profile).
For example, the 1st streaming shall be used for the live
monitoring, the 2nd streaming shall be used for recording to the
storage, and the 3rd streaming shall be used for the mobile
monitoring with the smartphone viewer.
The maximum frame rates of each combination are shown in the
following:
For the standard frame rate:
VIDEO SURVEILLANCE REMOTE DEVICES AND SENSORS
28 23 29 - 16
ARCHITECT & ENGINEER SPECIFICATIONS
SNC-WR602
For the high frame rate:
18. The camera shall be capable of supporting up to 20 users
simultaneously over the network.
19. The camera shall have up to 6 user level settings.
The administrator shall have complete access/control of the
cameras. The other 5 levels of access can be set to limit user
privileges to functions such as viewing, changing image size, etc.
Access to functions shall be determined as shown in the following
table:
VIDEO SURVEILLANCE REMOTE DEVICES AND SENSORS
28 23 29 - 17
ARCHITECT & ENGINEER SPECIFICATIONS
SNC-WR602
E. INTELLIGENT VIDEO ANALYTICS:
1. The camera shall have a unique conventional intelligent video
analytics named Distributed Enhanced Processing Architecture
Advanced (DEPA Advanced) to trigger an alarm based on userdefined rules.
2. The camera shall incorporate a built-in unique Intelligent Motion
Detection (IMD) capability.
To minimize false triggers, this Intelligent Motion Detection shall
compare the current image with prior 15 frames within the camera.
This algorithm shall allow the camera to discriminate against some
environmental noise such as shaking leaves or Auto Gain Control
maximum rate noise.
3. The camera shall have a Face Detection function which detects the
locations and sizes of human faces.
It detects facial features and ignores other objects, such as
buildings, trees, and bodies.
4. The camera shall have a camera tampering detection function that
alerts the operator if the camera is tampered with. Tampering can
include spraying of the camera lens, covering it with a cloth, or
changing of the mounting direction.
5. The camera shall have the following scene analytics, all of which
can be set from the camera setup menu:
- Intrusion: When a moving object enters the designated area, an
VIDEO SURVEILLANCE REMOTE DEVICES AND SENSORS
28 23 29 - 18
ARCHITECT & ENGINEER SPECIFICATIONS
SNC-WR602
alarm sounds.
- Passing: A passage line is determined, and when a moving object
passes the set line, an alarm sounds.
- Left Object Detection: When an object has been left unattended
for too long in the designated area, an alarm sounds
- Removed Object Detection: When an object has been removed
from the designated area, an alarm sounds.
VIDEO SURVEILLANCE REMOTE DEVICES AND SENSORS
28 23 29 - 19
ARCHITECT & ENGINEER SPECIFICATIONS
SNC-WR602
F. AUDIO:
1. The camera shall support bi-directional audio, using G.711 (64
kbps), G.726 (40, 32, 24, 16 kbps) and AAC (48, 16 kHz)
compression formats.
2. The camera shall be capable of storing and playing back up to 3
audio files.
Audio files shall be generated and transferred to the camera using
either the web browser or the manufacturer provided SNC audio
upload tool software.
3. The camera shall provide time stamps on the streaming audio.
Timestamps shall be inserted in the header area of the audio data.
4. The user shall have the ability to activate the microphone input via
the web interface.
VIDEO SURVEILLANCE REMOTE DEVICES AND SENSORS
28 23 29 - 20
ARCHITECT & ENGINEER SPECIFICATIONS
SNC-WR602
G. SYSTEM REQUIREMENTS & NETWORK:
1. The supported operating systems shall be Microsoft Windows 8.1
Pro 32 bit and 64 bit, Microsoft Windows 8 Pro 32 bit and 64 bit,
Microsoft Windows 7 32 bit and 64 bit (Ultimate/Professional),
Microsoft Windows Vista 32 bit (Ultimate/Business), and Microsoft
Windows XP 32 bit (Professional).
2. Minimum PC requirements shall be the Intel Core i7, 2.8 GHz or
higher, with 2 GB RAM or more supporting 1600 x 1200 or higher
resolution, 24-bit True Color display capability with Ethernet
100Base-TX.
3. The camera shall incorporate a built-in web server, such that the
standard web browser Microsoft Windows Internet Explorer
(version 7.0, 8.0, 9.0, 10.0, or 11.0 recommended) can be used to
access the camera without need for special viewer software.
4. The following web browsers can also be used to access the
camera with the plug-in free viewer: Firefox version 19.02, Safari
version 5.1 and Google Chrome version 25.0.
The plug-in free viewer enables the above browsers automatically
when they are started.
The plug-in free viewer display method will be selected
automatically.
ActiveX viewer can allow for H.264 (High/Main/Baseline Profile)
video streams and JPEG format images on the Google Chrome
version 25.0.
5. The camera shall support ActiveX viewer which allows the camera
image to be viewed in Internet Explorer.
The ActiveX viewer allows for recording of video and audio directly
to the PC‟s hard drive, and supports direct audio from the PC mic
to the camera.
6. The camera shall be capable of generating HTML code for the
video image, allowing for easy web page integration.
7. The camera shall support the following network protocols:
IPv4, IPv6, TCP, UDP, ARP, ICMP, IGMP*, HTTP, HTTPS, FTP
(client only), SSL, SMTP, DHCP, DNS, NTP, RTP/RTCP, RTSP
over TCP, RTSP over HTTP, and SNMP (v1, v2c, v3).
Network security shall be via password (basic authentication) and
IP filtering.
*Source-Specific Multicast (SSM) shall be supported.
VIDEO SURVEILLANCE REMOTE DEVICES AND SENSORS
28 23 29 - 21
ARCHITECT & ENGINEER SPECIFICATIONS
SNC-WR602
8. The camera shall have the capability to stream H.264
(High/Main/Baseline Profile) video in TCP protocol or H.264
(High/Main/Baseline Profile) video in UDP (unicast/multicast)
protocol.
9. The camera shall be capable of dynamic IP address change
notification. It shall accomplish this via an email to a specified
address or by HTTP when its IP address changes.
10. The camera shall support HTTPS client authentication.
11. The camera shall have an FTP client capability which allows the
following:
- Transferring a JPEG image to a pre-specified FTP server when
an alarm is triggered by either motion detection, camera tampering
detection or sensor input.
- Periodically capturing a JPEG image and transferring it to the
FTP server.
- At every position of the preset tour, capturing a JPEG image and
transferring it to the FTP server.
12. The camera shall have an email (SMTP) notification capability
which allows the following:
- Sending an email to pre-specified users when an alarm is
triggered by either motion detection, VMFs, camera tampering
detection, audio detection or sensor input. A JPEG image, which is
linked with the alarm trigger, can be attached to the email.
- Periodically capturing a JPEG image and sending it via email.
The range of the SMTP port number shall be from 1 to 65535.
13. The camera shall send Alarm notifications by HTTP to up to 3
designated URL, when the defined events such as Tampering
alarm or network disconnection occurs in the camera.
14. The camera shall support POP3, APOP, and CRAM-MD5
authentication for SMTP transmission.
15. The camera shall support RTSP protocol based upon RFC 2326
and shall support the following options: DESCRIBE, SETUP, PLAY,
TEARDOWN, and GET_PARAMETER.
VIDEO SURVEILLANCE REMOTE DEVICES AND SENSORS
28 23 29 - 22
ARCHITECT & ENGINEER SPECIFICATIONS
SNC-WR602
16. The camera shall support QoS technology using Differentiated
Services Code Point (DSCP).
17. The camera shall support IP Filtering, whereby access to the
camera can be restricted to one or more groups of selected users.
Up to 10 different groups can be established by defining an IP
address range for each group.
18. The camera shall support IEEE 802.1X authentication, and shall:
- comply with the IEEE 802.1X standards,
- be capable of being integrated into an IEEE 802.1X network to
achieve high network security,
- support EAP-TLS mode to use a key pair from a Certificate
Authority (CA),
- support EAP-MD5 mode,
- support PEAP mode.
19. The camera shall have user configurable port settings.
20. Upon CGI command request, system log shall be recorded on a
built-in memory (non volatile memory).
21. The camera shall provide supplied applications with the camera as
a standard accessory in the CD-ROM.
The SNC easy IP setup Guide application shall provide the initial
networking setting and Windows firewall configuration.
VIDEO SURVEILLANCE REMOTE DEVICES AND SENSORS
28 23 29 - 23
ARCHITECT & ENGINEER SPECIFICATIONS
SNC-WR602
H. INETERFACES:
1. The camera shall have a composite analog video output in addition
to streaming video via Ethernet.
The composite analog video output can be used for monitoring
while installing the camera to adjust the field of view and focus.
2. The composite analog video output from the camera shall be a
BNC type connector accessible via pigtail (supplied).
A pigtail hole is waterproof with a cable holder with a waterproof
rubber gasket. A LAN cable holder for conduit with a waterproof
rubber gasket is also supplied.
3. The composite analog video output from the camera shall be 1.0 V
peak-to-peak @ 75 ohms, unbalanced, sync negative via a BNC
type connector.
4. Horizontal resolution shall be 700 TV lines (4:3 aspect ratio, analog
video).
5. The camera shall have mini jack connectors to support external
microphone and active speakers. Mic/Line input shall be
switchable.
Mic input shall be monaural, 2.2 kilo ohms, DC 2.5 V plug-in-power,
Line input shall be monaural, and active speaker output shall have
a maximum output level of 1 Vrms.
6. The camera shall have an RJ-45 socket on the rear of the camera.
7. The network interface shall be via an 8-pin RJ-45 connector,
10Base-T/100Base-TX Ethernet.
Both IPv6 and IPv4 are supported.
8. The camera shall have a 14-pin I/O interface located on the rear of
the camera.
There shall be 4 alarm input ports, and 2 alarm/relay output ports.
The alarm input ports shall be opto-isolated.
For the alarm output ports, the timer execution shall be able to be
selected.
9. The camera shall support 4 optically isolated sensor inputs, and 2
relay outputs.
The interface shall be via a supplied I/O harness 14-pin cable.
10. The camera shall provide sensor-in/relay-out ports for interfacing
with external equipment.
The sensor input shall be configurable for either „make contact‟ or
„break contact‟ configuration.
VIDEO SURVEILLANCE REMOTE DEVICES AND SENSORS
28 23 29 - 24
ARCHITECT & ENGINEER SPECIFICATIONS
SNC-WR602
11. 2 relay outputs shall be rated at AC 24 V/DC 24 V, 1 A or less.
12. The camera shall have RS-422 and RS-485 interfaces and support
the Pelco D protocol.
13. The camera shall have a built-in SD card slot for an on-board
recording capability for movies and still pictures.
The maximum number of recording shall be up to 4,000.
The camera notify the specified* SD card maintenance information.
SD card up to 64 GB shall be available.
*Supported SD cards will be announced to update in the future.
14. IO assignment: I/O Port
VIDEO SURVEILLANCE REMOTE DEVICES AND SENSORS
28 23 29 - 25
ARCHITECT & ENGINEER SPECIFICATIONS
SNC-WR602
I. GENERAL SPECIFICATIONS:
1. The camera input power shall be
a power voltage of AC 24 V ± 10%, 50 Hz/60, HPoE+ 4 line powersupply.
2. The power for HPoE+ 4 line shall be supplied by using PD9501G
of Microsemi PowerDsine or a similar power supply device via a
network cable.
If the power is supplied by HPoE+, the integrated heater is not
available. (The camera in the activation temperature range shall be
+32 °F to +122 °F (0 °C to +50 °C ).)
3. The power connection for AC 24 V operation shall be by means 3pin Phoenix connector on a pigtail.
AC 24 V : 21.6 to 26.4 V
UL cable (VW-1 style 10368) shall be needed for for AC 24 V
connections.
4. Power consumption for the camera shall be 80.0 W maximum.
5. The camera operating temperature shall be within the following
range:
-40 ˚F to +122 °F (-40 ˚C to +50 ˚C) (AC 24 V)
+23 °F to +122 °F (-5 °C to +50 °C) (HPoE+)
6. The camera starting temperature shall be within the following
range:
-40 ˚F to +122 °F (-40 ˚C to +50 ˚C) (AC 24 V)
+32 °F to +122 °F (0 °C to +50 °C ) (HPoE+)
VIDEO SURVEILLANCE REMOTE DEVICES AND SENSORS
28 23 29 - 26
ARCHITECT & ENGINEER SPECIFICATIONS
SNC-WR602
7. The camera storage temperature shall be within the following
range:
-4 ˚F to +140 ˚F (-20 ˚C to +60 ˚C)
8. The camera operating humidity shall be within the range of 20 % to
80 % (non-condensing).
9. The camera storage humidity shall be within the range of 20 % to
95 % (non-condensing).
10. The camera shall have a built-in heater allowing the camera to
operate in extremely cold environments as low as -40 ˚F (-40 ˚C)
when the unit is powered by AC 24 V.
11. The camera dimensions (Dia. x H) shall be approximately:
8 3/4 inches x 12 7/8 inches (222.0 mm x 324.1 mm), not including
the projecting parts.
12. The camera shall weigh approximately 9 lb 0.6 oz (4.1 kg) .
13. The external material shall be:
Top sunshade: PC
Coupling: ADC12
Top cabinet: ADC12
Sun shade: PC
Dome flange: ADC12
14. The external color shall be:
Top sunshade: 6.4GY 8.0/0.3
Coupling: 3.6GY 8.4/0.3
Top cabinet: 3.6GY 8.4/0.3
Sun shade: 6.4GY 8.0/0.3
Dome flange: 3.6GY 8.4/0.3
VIDEO SURVEILLANCE REMOTE DEVICES AND SENSORS
28 23 29 - 27
ARCHITECT & ENGINEER SPECIFICATIONS
SNC-WR602
J. REGULATORY SPECIFICATIONS:
1. JATE Technical standard (LAN)
2. UL2044, IEC60950-1 (CB)
3. VCCI (Class A), FCC (Class A), IC (Class A)
4. Emission: EN55022 (Class A) + EN50130-4
5. Immunity: EN55022 (Class A) + EN55024
6. Emission: AS/NZS CISPR22 (Class A)
7. C-Tick Class A
8. Russia GOST-R
9. KCC
VIDEO SURVEILLANCE REMOTE DEVICES AND SENSORS
28 23 29 - 28
ARCHITECT & ENGINEER SPECIFICATIONS
SNC-WR602
K. SUPPLIED ACCESSORIES:
1. CD-ROM (supplied programs) (1)
2. Installation Manual (1)
3. Dome cover (1)
4. Top sunshade (1)
5. Coupling (1)
6. Wire fixing belt (1)
7. Wire bracket (1)
8. Bolts (2)
9. Power supply connector 3-pin (1)
10. I/O harness 14-pin (1)
11. Harness band (1)
12. Band mount (1)
13. Connection card (with BNC) (1)
VIDEO SURVEILLANCE REMOTE DEVICES AND SENSORS
28 23 29 - 29
ARCHITECT & ENGINEER SPECIFICATIONS
SNC-WR602
L. OPTIONAL ACCESSORIES:
1. YT-LDR632S Dome Cover Smoked
VIDEO SURVEILLANCE REMOTE DEVICES AND SENSORS
28 23 29 - 30
ARCHITECT & ENGINEER SPECIFICATIONS
SNC-WR602
M. DIMENSIONS:
VIDEO SURVEILLANCE REMOTE DEVICES AND SENSORS
28 23 29 - 31
ARCHITECT & ENGINEER SPECIFICATIONS
SNC-WR602
©2014 Sony Corporation
Features and specifications are subject to change without notice. Non-metric
weights and measurements are approximate.
Sony is a registered trademark of Sony Corporation.
IPELA, IPELA ENGINE PRO, DEPA, and Exmor are trademarks of Sony
Corporation.
Microsoft, Windows, Windows Vista, Internet Explorer and DirectX are either
registered trademarks or trademarks of Microsoft Corporation in the United
States and/or other countries.
Intel, Pentium and Intel Core are trademarks or registered trademarks of Intel
Corporation or its subsidiaries in the United States and other countries.
All other trademarks are the property of their respective owners.
VIDEO SURVEILLANCE REMOTE DEVICES AND SENSORS
28 23 29 - 32
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising