Bloomfield Coffee Brewers
603
10 Sunnen Drive
St. Louis, MO 63143
telephone: 314-678-6336
fax: 314-781-2714
www.bloomfieldworldwide.com
OWNERS MANUAL
For
Model 8774 Brewer
with optional
8881 Airpot
INTEGRITY™
COFFEE BREWERS
MODELS
8773 Automatic Airpot Brewer
8774 Pour-Over Airpot Brewer
Domestic and
Export Models
Includes:
Installation
Use & Care
Servicing Instructions
Model 8773 Brewer
with optional
7760 Airpot
p/n 2M-76451 Rev. F M603
141119
WARRANTY STATEMENT
All equipment manufactured by Bloomfield is warranted against defects in
materials and workmanship for the time periods listed in the chart starting
from the date the equipment is placed into service and is for the benefit of
the original purchaser:
THE FOREGOING OBLIGATION IS EXPRESSLY GIVEN IN LIEU OF
ANY OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING
ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE, WHICH ARE HEREBY EXCLUDED.
BLOOMFIELD, LLC SHALL NOT BE LIABLE FOR INDIRECT,
INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES FROM
ANY CAUSE WHATSOEVER.
This warranty is void if it is determined that upon inspection by an
authorized service agency that the equipment has been modified,
misused, misapplied, improperly installed, or damaged in transit or by
fire, flood or act of God.
Equipment
pour over, automatic coffee brewers
EBC, EMAX coffee brewers
* EBC, EMAX coffee brewer control
POD coffee brewers
ECO coffee brewers
coffee warmers
in room brewers
tea brewers
tea dispensers
tea dispenser BBTea
hot water machines
thermal servers
airpots
decanters
Parts
Labor
2 yrs.
2 yrs.
2 yrs.*
2 yrs.
3 yrs.
no labor
1 yr.
1 yr.
1 yr.
1 yr.
1 yr.
1 yr.
1 yr.
1 yr.
2 yrs.
2 yrs.
1 yr.
1 yr.
1 yr.
no labor
2 yrs.
2 yrs.
90 days
no labor
30 days
no labor
no warranty no warranty
It also does not apply if the serial nameplate has been removed or unauthorized service personnel perform service. The prices
charged by Bloomfield for its products are based upon the limitations in this warranty. Seller’s obligation under this warranty
is limited to the repair of defects without charge by a Bloomfield Authorized Service Agency or one of its sub-agencies. This
service will be provided on customer’s premises for non-portable models. Portable models (a device with a cord and plug or a
dispenser) must be taken or shipped to the closest authorized service agency, transportation charges prepaid, for services.
Agencies are located in principal cities, please visit our website to locate one.
This warranty is valid in the United States and Canada and void elsewhere. Please consult your classified telephone directory
or your food service equipment dealer; or, for information and other details concerning warranty, write to:
Service Parts Department; Bloomfield
10 Sunnen Drive, St. Louis, MO 63143
Phone: (314) 678-6336 : Fax: (314) 781-2714
Technical@ bloomfieldworldwide.com / www.bloomfieldworldwide.com
1. Resetting of safety thermostats, circuit breakers, overload protectors, or fuse replacements.
2. All problems due to operation at voltages other than specified on equipment nameplates - conversion to correct voltage
must be the customer’s responsibility.
3. All problems due to electrical connections not made in accordance with electrical code requirements and wiring diagrams
supplied with the equipment.
4. Replacement of items subject to normal wear, to include such items as knobs and light bulbs. Normal maintenance
functions including adjustment of thermostats, microswitches, and replacement of fuses and indicating lights are not
covered under warranty.
5. All problems due to inadequate water supply, such as fluctuating, or high or low water pressure.
6. All problems due to mineral/calcium deposits, or contamination from chlorides/chlorines. De-liming is considered a
preventative maintenance function and is not covered by warranty.
7. Full use, care and manuals may or may not be sent with each unit, only a condensed version. Please visit our web site to
download the full version.
8. Travel mileage is limited to fifty (50) miles from an authorized service agency or one of its sub-service agencies.
9. All labor shall be performed during normal working hours. Overtime premium shall be charged to the customer.
10. All genuine Bloomfield replacement parts are warranted for ninety (90) days from date of purchase on non- warranted
equipment. Any use of non-genuine Bloomfield parts completely voids any warranty.
11. Installation, labor and job checkouts are not considered warranty.
12. Charges incurred by delays, waiting time or operating restrictions that hinder the service technicians ability to perform
services are not covered by warranty. This includes institutional and correctional facilities.
SHIPPING DAMAGE CLAIMS PROCEDURE
NOTE: For your protection, please note that equipment in this shipment was carefully inspected and packaged by skilled
personnel before leaving the factory. Upon acceptance of this shipment, the transportation company assumes full responsibility
for its safe delivery.
IF SHIPMENT ARRIVES DAMAGED:
1. VISIBLE LOSS OR DAMAGE: Be certain that any visible loss or damage is noted on the freight bill or express receipt,
and that the note of loss or damage is signed by the delivery person.
2. FILE CLAIM FOR DAMAGE IMMEDIATELY: Regardless of the extent of the damage.
3. CONCEALED LOSS OR DAMAGE: if damage is unnoticed until the merchandise is unpacked, notify the
transportation company or carrier immediately, and file “CONCEALED DAMAGE” claim with them. This must be done
within fifteen (15) days from the date the delivery was made to you. Be sure to retain the container for inspection.
Bloomfield cannot assume liability for damage or loss incurred in transit. We will, however, at your request, supply you with the
necessary documents to support your claim.
603 p/n 76451 8773_8774 Owmers Manual
BLOOMFIELD SERVICE POLICY AND PROCEDURE GUIDE ADDITIONAL WARRANTY EXCLUSIONS
TABLE OF CONTENTS
WARRANTY STATEMENT xi
SPECIFICATIONS 1
FEATURES & OPERATING CONTROLS
2
PRECAUTIONS & GENERAL INFORMATION
3
AGENCY LISTING INFORMATION
3
INSTALLATION INSTRUCTIONS
4
OPERATION 6
BREWING COFFEE
8
CLEANING INSTRUCTIONS
9
TROUBLESHOOTING SUGGESTIONS
10
SERVICING INSTRUCTIONS11
Deliming Instructions
16
EXPLODED VIEWS & PARTS LISTS
18
SERVICE KITS22
WIRING DIAGRAMS23
Thank You for purchasing this
Bloomfield appliance.
Proper installation, professional
operation and consistent
maintenance of this appliance will
ensure that it gives you the very
best performance and a long,
economical service life.
This manual contains the
information needed to properly
install this appliance, and to use,
care for and maintain or repair the
appliance in a manner which will
ensure its optimum performance.
SPECIFICATIONS
MODEL
STYLE
8773
8773AU
8773EU
8773UK
POUR-OVER plus
AUTOMATIC W/HOT WATER
FAUCET
8774
8774AU
8774EU
8774UK
POUR-OVER ONLY
603 p/n 76451 8773_8774 Owmers Manual
8774KO
VOLTS 1ø
WATTS
AMPS
POWER SUPPLY
CORD
120
1500
12.5
NEMA-5-15P
240
1800
7.5
220-240
1800
7.5
120
1500
12.5
240
1800
7.5
220-240
1800
7.5
220
1500
6.9
Also meets Canadian standards.
Meets European standards
1
SUPPLIED
NEMA-5-15P
SUPPLIED
IL1626
Fig. 1 Features & Operating Controls
2
603 p/n 76451 8773_8774 Owmers Manual
FEATURES AND OPERATING CONTROLS
PRECAUTIONS AND GENERAL INFORMATION
WARNING: ELECTRIC SHOCK HAZARD
All servicing requiring access to non-insulated components must be performed by qualified
service personnel. Do not open any access panels which require the use of tools.
Failure to heed this warning can result in electrical shock.
WARNING: INJURY HAZARD
All installation procedures must be performed by qualified personnel with full knowledge of all
applicable electrical and plumbing codes. Failure could result in property damage and
personal injury.
WARNING: ELECTRIC SHOCK HAZARD
Brewer must be properly grounded to prevent possible shock hazard. DO NOT assume a
plumbing line will provide such a ground. Electrical shock will cause death or serious Injury.
WARNING: BURN HAZARD
This appliance dispenses very hot liquid. Serious bodily injury from scalding can occur from
contact with dispensed liquids.
CAUTION:
This appliance is intended for commercial use only.
This appliance is intended for use to brew beverage products for
human consumption. No other use is recommended or
authorized by the manufacturer or its agents.
This appliance is intended for use in commercial establishments,
where all operators are familiar with the appliance use,
limitations and associated hazards. Operating instructions and
warnings must be read and understood by all operators and
users.
Except as noted, this piece of equipment is made in the USA and
has American sizes on hardware. All metric conversions are approximate and can vary in size.
603 p/n 76451 8773_8774 Owmers Manual
The following trouble shooting, component views and parts lists
are included for general reference, and are intended for use by
qualified service personnel.
EQUIPMENT DAMAGE
DO NOT plug in or energize this
appliance until all Installation
Instructions are read and followed.
Damage to the Brewer will occur if
these instructions are not followed.
CAUTION:
BURN HAZARD
Exposed surfaces of the
appliance, brew chamber and
Airpot may be HOT to the touch,
and can cause serious burns.
This manual should be considered a permanent part of this
appliance. The manual must remain with the appliance if it is
sold or moved to another location.
AGENCY LISTING INFORMATION
This brewer is
and
listed under UL file E9253.
This brewer meets
Standard 4 only when installed,
operated and maintained in accordance with the enclosed
instructions.
Models as designated on page 1 meet
E9253
requirements.
STD 4
3
E9253
INSTALLATION INSTRUCTIONS
READ THIS CAREFULLY BEFORE STARTING THE INSTALLATION
EQUIPMENT DAMAGE
DO NOT plug in or energize this
appliance until all Installation
Instructions are read and
followed. Damage to the Brewer
will occur if these instructions are
not followed.
CAUTION:
UNSTABLE
EQUIPMENT HAZARD
It is very important for safety
and for proper operation that the
brewer is level and stable when
standing in its final operating
position. Provided adjustable,
non-skid legs must be installed at
each corner of the unit.. Failure
to do so will result in movement
of the brewer which can cause
personal Injury and/or damage to
brewer.
IMPORTANT:
This equipment must be installed
to comply with all applicable
federal, state and local plumbing
codes and ordinances.
NOTE: Water supply inlet line
must meet certain minimum
criteria to insure successful
operation of the brewer.
Bloomfield recommends 1/4”
copper tubing for installation of
less than 25 feet and 3/8” for
more than 25 feet from a 1/2”
water supply line.
Unpack the unit. Inspect all components for completeness and
condition. Ensure that all packing materials have been removed
from the unit.
Verify that the Spray Head Gasket and Spray Disk are properly
installed.
LEVELING THE UNIT
Verify that an adjustable leg is installed at each corner of the
brewer, and that a rubber foot is installed on each leg.
Set Brewer in its operating location. Level the Brewer. A spirit
level should be placed on the top of the unit, at the edge, as a
guide when making level adjustments.
Level the unit from left to right and front to back by turning the
adjustable feet. Be sure all four feet touch the counter to prevent
tipping.
PLUMBER’S INSTALLATION INSTRUCTIONS (MODEL 8773
BREWERS ONLY)
Brewer should be connected to a POTABLE WATER, COLD
WATER line. Flush water line before connecting to Brewer.
DO NOT use a saddle valve with a self-piercing tap for the water
line connection. Such a tap can become restricted by waterline
debris. For systems that must use a saddle tap, shut off the
main water supply and drill a 3/16” (minimum) tap for the saddle
connection, in order to insure an ample water supply. Remember
to flush the line prior to installing the saddle.
The brewer must be installed on a water line with average
pressure between 20 PSI and 90 PSI. If your water pressure
exceeds 90 PSI at anytime, a pressure regulator must be
installed in the water supply line to limit the pressure to not more
than 90 PSI in order to avoid damage to lines and solenoid.
A water shut-off valve should be installed on the incoming water
line in a convenient location (Use a low restriction type valve,
such as a 1/4-turn ball valve, to avoid loss of water flow thru the
valve.
NSF requires that the brewer be able to be moved for cleaning
underneath. A flex line or loops of copper tubing will satisfy this
requirement. See Fig. 2 at right.
4
603 p/n 76451 8773_8774 Owmers Manual
CAUTION:
INSTALLATION INSTRUCTIONS (continued)
WARNING:
SHOCK HAZARD
IL1596
Brewer must be properly
grounded to prevent possible
shock hazard. DO NOT
assume a plumbing line
will provide such a ground.
Electrical shock will cause death
or serious injury.
Fig. 2 Water Supply Installation - New-Style Brewers
In some areas, local codes require a backflow preventer (check
valve) to be installed on the inlet water line. If a backflow
preventer is used, you must install a water hammer arrester in
the incoming line, between the backflow preventer and the brewer inlet, as far away from the brewer as space will allow. This will
relieve the excessive back pressures that can cause faucet leaks
and solenoid malfunctions.
ELECTRICIAN’S INSTALLATION INSTRUCTIONS
REFER TO ELECTRICAL SPECIFICATIONS - Page 1
Check the nameplate to determine correct electrical service
required for the Brewer to be installed.
IMPORTANT: Before connecting to electricity, make sure
automatic brewers are connected to the water supply.
Domestic models 8773 & 8774 are equipped with a cord and
plug. They require a 115 - 125 volt 15 amp circuit (50/60 Hz,
2 wire plus ground, with NEMA 5-15R receptacle).
603 p/n 76451 8773_8774 Owmers Manual
Export models 8773 & 8774 are equipped with a cord and plug.
Refer to page 1 for circuit voltage requirements.
5
IMPORTANT:
Do not connect brewer to
electrical power until the tank
is filled with water. Pour water
into the pour-over opening until
water flows from the brew head.
IMPORTANT:
Supply power must match
nameplate for voltage and
phase. Connecting to the wrong
voltage will damage the brewer
or result in decreased performance. Such damage is not
covered by warranty.
IMPORTANT:
The ground prong of the plug
is part of a system designed to
protect you from electrical shock
in the event of internal damage. Never cut off the ground
prong nor twist a blade to fit an
existing receptacle. Contact a
licensed electrician to install the
proper circuit and receptacle.
OPERATION
IL1627
Fig. 3 Model 8773 Operation Diagram
A. START-UP
For initial start-up, or if the brewer has not been used for an
extended period of time:
Be sure spray disk and brew gasket are properly installed in the brew head.
For automatic brewers, be sure the water supply is properly
connected and the water supply valve is turned ON.
BEFORE plugging the brewer into a receptacle, or otherwise connecting brewer to electrical power THE WATER TANK MUST BE FILLED. Place an empty container under the brew head. Lift the pour-over cover then pour three decanters of warm tap water into the pour-over opening. Water will begin to flow from the brew head. When all water flow stops, empty the container.
Once the tank is full of water, connect the brewer to electrical power. Press the tank heater switch to ON. The heating elements will begin heating the water in the tank. When the water has reached the proper temperature, the “READY TO BREW” light will glow.
IL1618
Fig. 4 Fill the Tank
6
603 p/n 76451 8773_8774 Owmers Manual
IMPORTANT:
Tank must be full of
water before connecting
brewer to electrical power.
Heating elements will be
damaged if allowed to
operate without being fully
submerged in water.
Damage caused by
operating the brewer
without water in the tank
is NOT COVERED BY
WARRANTY.
OPERATION (continued)
WATER HEATER
Water temperature is sensed by a
thermobulb inserted into the water tank. This
temperature signal is fed to the thermostat,
which controls line power to the heating
element.
The setpoint temperature is adjustable at the
thermostat.
The element is protected from over-temperature by a hi-limit thermostat.
To save energy, press the TANK HEAT switch
to OFF if no brew is expected for an
extended period.
Fig. 5 Heat Control Diagram
WATER FLOW
M ANUAL
P O U R -O V ER
B A SIN
PAN
POUR-OVER FEATURE (8773 & 8774)
Pouring any amount of cold water into the
pour-over opening and into the basin pan
forces an identical amount of hot water out
of the tank and through the spray head into
the brew chamber.
BREW
TA N K
E S O LE N O ID
AUTOMATIC OPERATION (8773 only)
603 p/n 76451 8773_8774 Owmers Manual
Pressing BREW button energizes the
solenoid valve, allowing water from an
external water supply to flow into the basin
pan and then into the hot water tank. This
forces an identical amount of hot water out
of the tank and through the spray head into
the brew chamber
B A SIN
PAN
FA U C E T
B Y PA S S
BREW
The solenoid uses a flow control device so
that flow is consistent between 20 p.s.i. and
90 p.s.i.
TA N K
E S O LE N O ID
Length of time the solenoid is open is
controlled by the timer.
FA U C ET
S H U T-O FF
VA LV E
HOT WATER FAUCET (8773 only)
FA U C ET
FA U C E T
B Y PA S S
The faucet water coil is submerged in the
hot water tank and draws heat from the brew
water. Water going to the water coil is not
controlled by the solenoid valve.
Hot water is provided at the faucet, at supply
water pressure, any time the faucet shut-off
valve is OPEN.
M ANUAL
P O U R -O V ER
W ATE R
C O IL
TA N K
Fig. 6 Water Flow Diagram
7
IL1604
HO T
W ATE R
BREWING COFFEE
BURN HAZARD
Exposed surfaces
of the brewer, brew chamber and airpot may be
HOT to the touch, and can
cause serious burns.
CAUTION:
BURN HAZARD
To avoid splashing or
overflowing hot liquids,
ALWAYS place an empty
airpot under the brew
chamber before starting
the brew cycle. Failure to
comply can cause serious
burns.
CAUTION:
BURN HAZARD
After a brew cycle, brew
chamber contents are
HOT. Remove the brew
chamber and dispose of
used grounds with care.
Failure to comply can
cause serious burns.
NOTE:
Water for the hot water
faucet is heated in a coil
inside of the water tank.
Use of the faucet will
not affect the volume of
water delivered for a brew.
However, overuse of the
faucet during a brew may
lower the temperature of
the brew water. Draw no
more than one (1) cup of
water at a time.
A.PREPARATION
Place one (1) genuine Bloomfield
paper filter in the brew chamber.
Add a pre-measured amount of
fresh coffee grounds.
Gently shake the brew chamber to
level the bed of grounds. Slide the
brew chamber into place under the
brew head.
PAPER
FILTER
BREW
CHAMBER
IL1605
Fig. 7 Brew Chamber
B. POUR-OVER OPERATION
NOTE: Any Integrity™ brewer can be used in the pour-over mode.
Press the TANK HEATER switch to ON. Wait until the “READY TO BREW” light is lit.
Place the appropriate EMPTY airpot in place under the brew chamber.
Fill an airpot identical to the one being used, with tap water. Lift the pour-over cover and pour the entire contents of the airpot into the pour-over opening, which will fill the basin.
Water from the basin will displace a like amount of heated water from the tank. The hot water will be forced into the brew head where it will spray over the bed of grounds. Freshly brewed coffee will begin to fill the container under the brew chamber. When the flow and all dripping stops, the coffee is ready to serve.
Discard the contents of the brew chamber. Rinse the brew chamber in a sink. When the ”READY TO BREW” light glows, the brewer is ready for another brew cycle.
C. AUTOMATIC OPERATION (8773 only)
Press the TANK HEATER switch to ON. Wait until the “READY TO BREW” light is lit.
Place the appropriate EMPTY airpot in place under the brew
chamber.
Press the “BREW” switch. The solenoid will open for an amount of time determined by the timer setting, admitting a measured quantity of water into the basin.
Water from the basin will displace a like amount of heated water from the tank. The hot water will be forced into the brew head where it will spray over the bed of grounds. Freshly brewed coffee will begin to fill the container under the brew chamber. When the flow and all dripping stops, the coffee is ready to serve.
Discard the contents of the brew chamber and rinse it in a sink. When the ”READY TO BREW” light glows, the brewer is ready for another brew cycle.
8
603 p/n 76451 8773_8774 Owmers Manual
CAUTION:
CLEANING INSTRUCTIONS
PROCEDURE: Clean Coffee Brewer
PRECAUTIONS: Disconnect brewer from electric power.
Allow brewer to cool.
FREQUENCY: Daily
TOOLS: Mild Detergent, Clean Soft Cloth or Sponge
Bristle Brush, Bottle Brush
BURN HAZARD
Brewing and serving
temperatures of coffee are
extremely hot.
Hot coffee will cause
serious skin burns.
CAUTION:
1. Disconnect brewer from electric power.
Allow brewer to cool before cleaning.
SHOCK HAZARD
Do not submerge or immerse
brewer in water.
2. Remove airpot.
3. Remove and empty brew chamber.
4. Remove the spray disk from the brew head (See figure 8):
CAUTION:
Press up on the spray disk ears, then turn the disk to the left to unlatch. Remove the gasket from inside the brew head.
5. Wipe inside of brew head and area around the brew head with a soft clean cloth or sponge moistened with clean water.
IMPORTANT:
DO NOT use steel wool, sharp
objects, or caustic, abrasive or
chlorinated cleansers to clean
the brewer, airpots.
6. Wash the spray disk in a sink using warm water and a mild
detergent. A bristle brush may be used to clear clogged spray holes. Rinse the spray disk with clean water and allow to air dry.
7. Wash the brew chamber in a sink using warm water and a mild detergent. A bristle brush may be used to clean the inside. Rinse with clean water and allow to air dry.
8. Wipe the exterior of the brewer with a soft clean cloth or sponge moistened with clean water.
GASKET
10. Reinstall the gasket INSIDE the brew head, then reinstall the spray disk.
SPRAY
DISK
LIFT EARS UP
TURN LEFT TO
REMOVE
603 p/n 76451 8773_8774 Owmers Manual
11. Reinstall the brew chamber.
12. DO NOT submerge airpots in water. Clean airpots by filling with warm soapy water. Scrub the inside with a bottle brush. Empty and rinse with clean water. Wipe the exterior with a soft clean cloth or sponge moistened with clean water. Invert and allow to air dry.
Procedure is complete
9
IL1599
Fig. 8 Cleaning
TROUBLESHOOTING SUGGESTIONS
Water won’t heat (be sure TANK
HEAT switch is ON)
Coffee level low (pour-over)
Coffee level too high or low
(automatic)
Brew chamber overflows
Sprays water from brew head
No brew (automatic)
No flow from hot water faucet
Poor coffee quality
POSSIBLE CAUSE
SUGGESTED REMEDY
Brewer unplugged or circuit breaker
tripped
Check power supply cord Check /
reset circuit breaker
Thermostat set too low
Set for desired temperature
Hi-Limit thermostat tripped
Allow to cool, Reset hi-limit (8786,
8788)
Damaged internal component or wiring
Examine wiring & connectors,
thermostat and heating element,
Repair/replace as needed
Pour-over - no water or too little water
added at startup
Be sure to add sufficient water
Not enough water poured in
Increase water amount
Too much coffee grounds
Adjust amount of grounds
Timer out of adjustment
Adjust timer
Too many filter papers or wrong filter
paper
Use one (1) genuine Bloomfield filter
per brew
Brew chamber dispense hole plugged
Thoroughly clean brew chamber
Too much coffee or too fine a grind
Adjust coffee amount and grind
Spray gasket improperly installed
Check/reinstall gasket on INSIDE of
brew head
Spray disk plugged
Clean spray disk
Water supply OFF
Turn water supply ON
Solenoid strainer plugged
Clean strainer
Water filter (if used) plugged
Replace filter element
Bad BREW switch
Replace switch
Damaged internal component or wiring
Examine wiring & connectors, brew
switch and solenoid Repair/replace as
needed
Faucet valve turned OFF
Turn faucet valve ON
Faucet plugged
Disassemble faucet, clean
Water not hot enough or too hot
Adjust water temp 195-205ºF
Spray disk not installed
Properly installed spray disk and
gasket
Keep brewer, airpots and servers clean. Install a taste and odor filter in water
supply, and replace cartridges regularly. Use a quality coffee with a consistent
roast. Use proper grind and amount of coffee per brew.
10
603 p/n 76451 8773_8774 Owmers Manual
SYMPTOM
SERVICING INSTRUCTIONS
ACCESS PANELS
TOP PANEL:
Remove top panel to access hot water tank, thermostat, heating
elements, brew circuit tubing, faucet valve and piping.
Top panel is held by two screws at the rear and a retaining lip at
the front.
FRONT PANEL:
Remove front panel to access timer .
Front panel is held by a screws through the bottom panel and a
retaining lip at the top.
CAUTION:
SHOCK HAZARD
Opening access panels or
removing warmer plates on this
brew may expose uninsulated
electrical components.
Disconnect brewer from
electrical power before
removing any panel or warmer
plate.
SOLENOID DOOR:
Remove solenoid door to access solenoid and plumbing
connections.
Solenoid door is held by two screws and a retaining lip.
603 p/n 76451 8773_8774 Owmers Manual
IL1629
Fig. 9 Access Panels
11
SERVICING INSTRUCTIONS (continued)
TEMPERATURE ADJUSTMENT
CAUTION:
SHOCK HAZARD
Unplug power cord or turn circuit breaker OFF. Remove top
panel.
These procedures involve
exposed electrical circuits.
These procedures are to
be performed by qualified
technical personnel only.
Pull vent tube out of tank lid and insert a thermometer of known
accuracy in vent hole. Reconnect brewer to electrical power.
IMPORTANT:
A mechanical thermostat will
maintain temperature within
±5ºF. To prevent boiling water
in the brewer, thermostat should
be adjusted to a maximum
temperature equal to the local
boiling temperature minus 5ºF.
Fig. 10an Checking
and Adjusting
Brewchamber.
Temperature
Place
empty decanter
under brew
Energize
brewer and pour one decanter (64 oz.) of cold water into pourover opening. When READY TO BREW light comes on, read
temperature displayed on thermometer.
Adjust thermostat by turning shaft; clockwise increases
temperature. 1/8 turn = approximately 10ºF.
Refer to Table 1 below for proper brewing temperature based on
altitude.
BOILING
POINT OF
WATER
NOTE: 1/8 turn = approximately
10ºF (5.6ºC).
TEMP ( F)
210
205
IDEAL
BREWING
TEMPERATURE
200
195
MAXIMUM
TEMPERATURE
SETTING
190
ELEVATION (feet above sea level)
97
IDEAL
BREWING
TEMPERATURE
94
91
MAXIMUM
TEMPERATURE
SETTING
0
05
0
1,
20
1, 0
35
0
1,
50
1, 0
65
0
1,
80
1, 0
95
0
0
1,
90
0
75
60
45
0
88
0
15
0
30
0
Fig. 11 Adjust Thermostat
TEMP ( C)
100
IL1606
ELEVATION (meters above sea level)
Table 1
IL1601
BOILING
POINT OF
WATER
IL1602
Boiling Temperature by Altitude
Upon completion, remove thermometer and reinstall vent tube.
12
603 p/n 76451 8773_8774 Owmers Manual
NOTE:
Optimum brewing temperature
range is 195ºF to 205ºF (90ºC
to 96ºC).
SERVICING INSTRUCTIONS (continued)
TIMER ADJUSTMENT (AUTOMATIC BREWERS ONLY)
The amount of water dispensed automatically during a brew cycle
is controlled by the timer.
Place empty decanter under brew chamber. Press BREW
button. Brewer should dispense one decanter of water. To adjust
amount:
Remove brew chamber and button plug. Adjust knob on timer;
clockwise increases time. Run several cycles to check amount
of water delivered. Replace button plug.
IMPORTANT: Water pressure
must be between 20 p.s.i and
90 p.s.i. flowing pressure.
If water pressure exceeds this
value, or if water pressure
varies greatly, a pressure
regulator must be installed in
the water supply line.
REMOVE TANK LID ASSEMBLY
Unplug brewer or turn circuit breaker OFF. Turn OFF water
supply. Remove top panel. Pull vent tube and inlet elbow out of
basin pan.
Pull water inlet tube out of basin pan. Remove basin pan.
On models with faucet, disconnect inlet pipe at faucet shut-off
valve and outlet pipe at faucet.
IMPORTANT: Before setting
assembly into tank, make sure
tank lid gasket is properly
seated on flange of lid. DO NOT
OVER-TIGHTEN.
Disconnect all wiring from thermostat, hi-limit, and heating
element.
Loosen center screw on tank hold-down bracket. Remove
hold-down bracket by sliding short slotted end off of locking stud
and lifting it off. Remove cover assembly by lifting it straight up.
Reassemble in reverse order.
REPLACE THERMOSTAT
Unplug brewer or turn circuit breaker OFF. Turn OFF water
supply. Remove top panel.
Disconnect all wiring from thermostat only. Loosen and free
jam nut from pass-thru fitting securing temperature sensing bulb.
Remove two screws holding thermostat to bracket.
603 p/n 76451 8773_8774 Owmers Manual
Lift out thermostat, sensing bulb and thermostat gasket.
Push sensing bulb into tank lid thermowell until fitting seats.
Tighten capillary lock nut only enough to ensure no water
leakage. Excessive tightening is not necessary.
Reassemble in reverse order.
13
IMPORTANT:
If mounting thermostat
p/n 8512-51, be sure to place
a new seal washer below the
fitting on the capillary line.
If replacing gray-bodied thermo
with p/n 8512-51, be sure to
remove tube from thermowell.
SERVICING INSTRUCTIONS (continued)
IMPORTANT:
When replacing heating element,
also replace seal gaskets.
REPLACE HEATING ELEMENT
Remove tank lid assembly per above.
Remove two hex nuts holding element to cover. Pull element
from mounting holes.
Reassemble in reverse order.
REPLACE SOLENOID
Symptom: Automatic brewer will not flow water; or,
automatic brewer drips continuously from brew head.
NOTE: Wrench p/n 2C-76660 is designed to allow easy removal
of the hoses from the plastic solenoid valve.
IMPORTANT: Shut-off water and electric supply to brewer before
removing hoses or wiring.
Remove water supply flare fitting:
a. Slide the 5/8” end of the wrench over the flats on the inlet fitting of the valve.
b. Hold the wrench to prevent the inlet fitting from turning while installing or removing the inlet water supply flare nut.
Remove braided hose:
a. Slide the 7/16” end of the wrench between the valve body and the white ring on the extreme end of the metal hose fitting.
b. Pressure on the white ring toward the metal ferrule releases the clinch ring, allowing the hose to be easily slid off of the solenoid bypass outlet.
c. Install hose on new valve by pressing end of hose onto bypass outlet until it is fully seated.
STRAINER
SCREEN
WASHER
WATER INLET
FITTING
IL1608
Fig. 12
Clean Strainer Screen
Disconnect wiring.
Remove two screws holding solenoid to access door.
Reassemble in reverse order.
CLEAN SOLENOID SCREEN
Symptom: Automatic brewer will not flow water.
Unplug power cord or turn circuit breaker OFF. Turn OFF and
disconnect water supply from brewer inlet fitting.
Unscrew water inlet fitting from solenoid.
Using needle-nose pliers, withdraw strainer screen from solenoid.
Clean screen under faucet. A stiff bristle brush may be used if
necessary.
Reinsert screen in solenoid. Be careful to maintain correct
orientation. (The OPEN END of the screen goes in FIRST.)
Reassemble in reverse order.
14
603 p/n 76451 8773_8774 Owmers Manual
Fig. 11 Remove Faucet
Supply from Solenoid
SERVICING INSTRUCTIONS (continued)
REPLACE TIMER ASSEMBLY
Unplug power cord or turn circuit breaker OFF.
Remove front panel. Remove knob and three screws holding
timer to bracket. Disconnect wiring to timer.
Reassemble in reverse order.
Adjust timer as described on page 13
REPLACE HOT WATER FAUCET COIL
Symptom: Brewer drips continuously from brew head, except
when faucet valve is turned OFF.
Remove tank lid assembly per above.
IMPORTANT:
When replacing water faucet
coil, also replace seal gaskets.
Remove two hex nuts hot water coil to cover. Pull coil from
mounting holes.
Reassemble in reverse order.
REPAIR HOT WATER FAUCET
Open solenoid access door. Withdraw solenoid until hot water
faucet shut-off can be accessed. Turn faucet valve OFF.
Unscrew aerator cap from faucet and remove handle retaining
clip. Do not let faucet body turn.
Pull bonnet assembly from faucet body.
Examine the interior of the faucet body and the surface of the
seat cup. Clean out any debris in the faucet body, using a stiff
bristle brush if necessary.
Examine the aerator. Clean any debris from the screen or flow
straightener, using a stiff bristle brush if necessary.
Reassemble in reverse order.
603 p/n 76451 8773_8774 Owmers Manual
REPLACE BREW READY LIGHT or BREW BUTTON
Unplug power cord or turn circuit breaker OFF. Disconnect
electric leads.
Using Switch Removal Tool (p/n 83209) or a thin screwdriver,
compress mounting tabs then pry light or switch from mounting
hole.
Reassemble in reverse order.
15
NOTE: Any abrasion or
roughness on the flat end of the
seat cup will require replacing
the seat cup:
Work the seat cup out of the
bonnet and off of the end of the
stem.
Install a new seat cup, making
sure the knob on the stem is
fully inserted into the pocket of
the seat cup, and the skirt of the
seat cup is fully inserted into the
bonnet.
SERVICING INSTRUCTIONS (continued)
CHEMICAL BURN
HAZARD
Deliming chemicals may be
caustic. Wear appropriate
protective gloves and goggles
during this procedure.
Never siphon deliming
chemicals or solutions by
mouth.
This operation should only be
performed by qualified and
experienced service personnel.
IMPORTANT: DO NOT spill,
splash or pour water or deliming
solution into or over any internal
component other than the inside
of the water tank.
IMPORTANT: DO NOT allow
any internal components to
come into contact with the
deliming solution. Take care to
keep all internal components
dry.
NOTE: Repeat steps 4 thru 5
as required to remove all scale
and lime build-up.
PROCEDURE: Delime the Water Tank
PRECAUTIONS: Disconnect brewer from electric power.
Allow brewer to cool.
FREQUENCY: As required (Brewer slow to heat)
TOOLS: Deliming Solution
Protective Gloves, Goggles & Apron
Mild Detergent, Clean Soft Cloth or Sponge
Bristle Brush, Bottle Brush
Large Sink (or other appropriate work area)
1. Disconnect brewer from the electrical supply. For automatic brewers, turn off the water shut-off valve and disconnect the
water supply line from the brewer inlet fitting.
2.. Remove the tank lid assembly as described on page 13.
3. Remove the water tank from the brewer body by lifting
straight up. Empty all water from the tank. Set the tank back
into the brewer.
4. Mix 2 quarts of deliming solution according to the
manufacturer’s directions. Carefully pour the deliming
solution into the water tank. Lower the lid assembly back
onto the tank. Allow to sit for 30 minutes, or as directed by the manufacturer.
5. At end of soaking period, remove lid assembly from tank.
Thoroughly rinse internal components of lid assembly with
clear water. Using a stiff bristle brush, scrub the heating
element (and faucet water coil on automatic brewers) to
remove lime and calcium build-up. Rinse with clean water.
Store lid assembly in a safe location .
6. Remove the tank from the brewer and empty. Using a stiff bristle brush, scrub the interior of the water tank to remove lime and calcium build-up. Rinse with clean water.
16
603 p/n 76451 8773_8774 Owmers Manual
CAUTION:
SERVICING INSTRUCTIONS (continued)
7. Set the tank back into the brewer. Reassemble the tank lid to the water tank. Make sure the gasket is properly in place, then reinstall the hold-down strap.
8. Reinstall wiring to heating element and thermostat. Reinstall the hi-limit thermostat (if removed). For automatic brewers, reassemble piping for the faucet. Verify that all internal
components are dry, then reinstall the top panel.
9. Reconnect brewer to electrical supply and, for automatic
brewers, reconnect water supply.
10. Install the brew chamber without filter paper or grounds.
Run at least three full brew cycles and discard all water
generated.
603 p/n 76451 8773_8774 Owmers Manual
11. Brewer is ready to use.
17
NOTE: Normally, silicone hoses
do not need to be delimed.
Should deliming hoses become
necessary, Bloomfield
recommends replacing the
hoses.
EXPLODED VIEW & PARTS LIST
HOT WATER TANK ASSEMBLY
IL1630
ITEM
PART NO.
13
2C-70134
HOLD-DOWN STRAP
8773, 8774
2C-73457
NUT, HEX 8-32 KEPS
8773, 8774
50
WS-8512-51
THERMOSTAT (BLACK BODY - INCL. SEAL & MOUNTING SCREWS)
WS-86280
THERMO (ALT) (GRAY BODY - INCL. TUBE & MOUNTING SCREWS)
USED ON
8773, 8774
52
2C-70174
SEAL WASHER, THERMO CAP TUBE (ONLY)
8773, 8774
54
2I-70147
GASKET, TANK COVER
8773, 8774
55
2C-70151
NUT HEX 1/2-20 BRASS
56
2I-70152
SEAL GASKET, ELEMENT OR WATER COIL
57
2C-70151
NUT HEX 7/16-20 BRASS
58
2N-70149
HOT WATER COIL
59
2K-Z18254
TUBE, BASIN OUTLET/TANK INLET, SILICONE
8773, 8774
60
2V-70398
TUBE, VENT, SILICONE
8773, 8774
61
2K-70103
ELBOW, TANK OUTLET, SILICONE
8773, 8774
A6-70221
TAN COVER, PLATE ONLY, 6 HOLES
8774
A6-70142
TAN COVER, PLATE ONLY, 8 HOLES
8773
63
2T-47499
THERMOSTAT, HI-LIMIT
8773, 8774
66
2V-70144
WATER INLET TUBE
8773, 8774
66a
2C-70146
NUT, HEX 4-40 SS
8773, 8774
66b
2C-70145
SCREW 4-40 x 1 PAN HEAD
8773, 8774
62
67
68
8773
8773, 8774
8773
2N-70143UL
HEATING ELEMENT (120V, 1500W)
8773, 8774 120V
2N-70173UL
HEATING ELEMENT (240V, 1800W)
8773, 8774 220/240V
2D-70110
TANK BODY
8773, 8774
TANK COVER ASSEMBLY
WS-8543-300
WS-8541WF-300
INCLUDES: MOUNTED THERMO, HI-LIMIT & 120V 1500W HEATING
ELEMENT - NO WATER COIL)
INCLUDES: MOUNTED THERMO, HI-LIMIT, 120V 1500W HEATING
ELEMENT & HOT WATER COIL)
18
603 p/n 76451 8773_8774 Owmers Manual
14
DESCRIPTION
EXPLODED VIEW & PARTS LIST (continued)
CABINET PLUMBING COMPONENTS
10
9
45
603 p/n 76451 8773_8774 Owmers Manual
USED ON ALL
MODELS
TANK ASSY
see PAGE 18
USED ON
8773 ONLY
IL1631a
ITEM
PART NO.
8
2V-70104
FORMED TUBE, FAUCET OUTLET ASSEMBLY 10-7/8” LONG
DESCRIPTION
8773
USED ON
9
2V-70111
FORMED TUBE, FAUCET COIL INLET ASSEMBLY
8773
10
A6-70118
VALVE NEEDLE ASSEMBLY
8773
12
2J-75681
HOSE BRAID 6MMX299MM
8773
18
2K-70096
ELBOW, BASIN INLET DIVERTER POLYPROPYLENE
8773, 8774
24
2V-70131
TUBE, BREW OUTLET, METAL 4-3/4” LONG
8773, 8774
25
2K-70130
ELBOW, SPRAYER, SILICONE
8773, 8774
26
2C-72680
LOCK NUT, HEX 7-16-20
8773
27
2C-70107
LOCK WASHER 7/16” EXT SEMS (FAUCET)
28
2C-72681
WASHER, FLAT 15/32” x 1-1/8” x 1/16” SS
29
WS-82556
FAUCET ASSEMBLY, PRESSURE
33
2I-70139
GASKET, SPRAY HEAD
34
A6-72727
SPRAY DISK, EMBOSSED
34a
A6-70163
RETAINER, SPRAY HEAD (REQUIRES DRILL/RIVETS TO INSTALL)
43
2V-70144
TUBE, BASIN INLET, SILICONE 10”
2V-70124
VLV-SOL, 120V METAL, 75GPM
2E-75685
SOLENOID W/BYPASS, 120V, .75 GPM
2E-74570
SOLENOID W/BYPASS, 220/240V, .75 GPM
2K-Z18254
TUBE, BASIN OUTLET/TANK INLET, SILICONE
45
59
60
2V-70398
TUBE, VENT, SILICONE
61
2K-70103
ELBOW, TANK OUTLET, SILICONE
108
2D-70095
BASIN PAN
WS-82573
HANDLE, FAUCET RED (29a)
WS-82575
WS-82682
SEAT CUP (29c)
FAUCET REPAIR KIT, INCL: HANDLE (29a), SEAT CUP (29c), SPRING (29d), STEM (29h),
PIN (29j) & BONNET (29k)
RETAINER CLIP (29b)
WS-84804
AERATOR REPLACEMENT, INCL: O-RING (29e), DISK (29f) & CAP (29g)
WS-84870
AERATOR REPAIR KIT, INCL: O-RING (29e) & DISK (29f)
FAUCET REPAIR KITS
WS-82576
19
EXPLODED VIEW & PARTS LIST (continued)
ELECTRICAL COMPONENTS
IL1632
ITEM
PART NO.
30
2E-70733
31
2E-70395
SWITCH, TANK HEAT/ENERGY SAVER
8773, 8774
2J-72671
INDICATOR, 120V, READY-TO-BREW
8773, 8774 (US & Canada)
35
36
37
45
47
50
63
67
USED ON
8773
2J-70644
INDICATOR, 240V, READY-TO-BREW
8773, 8774 (Export)
2P-70128
TIMER, 2-MINUTE (WITH DIAL & KNOB) 120V
8773 (US & Canada)
2P-70054
TIMER, 2-MINUTE (WITH DIAL & KNOB) 240V
8773 (Export)
2E-70353
POWER CORD ASSEMBLY, 120V NEMA 5-15P
8773, 8774 (US & Canada)
DD-70647
POWER CORD ASSEMBLY, 240V (AU)
8773, 8774 (Australia)
A6-71156
POWER CORD ASSEMBLY, 240V (EU)
8773, 8774 (Europe, Korea)
A6-WL0139
POWER CORD ASSEMBLY, 240V (UK)
8773, 8774 (UK)
2K-70215
STRAIN RELIEF (US & Canada)
8773, 8774 (US & Canada)
2K-70648
STRAIN RELIEF (AU, EU, KO, UK)
8773, 8774 (Export)
2E-75685
SOLENOID W/BYPASS, 120V, .75 GPM
8773 (US & Canada)
2E-74570
SOLENOID W/BYPASS, 220/240V, .75 GPM
8773 (Export)
2E-70709
TERMINAL BLOCK, 4P
8774AU
WS-8512-51
THERMOSTAT (BLACK BODY - INCL. SEAL & MOUNTING SCREWS)
WS-86280
THERMO (ALT) (GRAY BODY - INCL. TUBE & MOUNTING SCREWS)
2T-47499
8773, 8774
THERMO, HI-LIMIT
8773, 8774
2N-70143UL
HEATING ELEMENT (120V, 1500W)
8773, 8774 120V
2N-70173UL
HEATING ELEMENT (240V, 1800W)
8773, 8774 220/240V
SOLENOID REPAIR KITS
2E-74570
SOLENOID 220/240V W/BYPASS .75GPM, COMPLETE
2E-75685
SOLENOID 120V W/BYPASS .75GPM, COMPLETE
WS-85218
INLET FITTING KIT INCLUDES: CAP (45a), FITTING (45b), GASKET
(45c) & STRAINER (45d)
WS-85219
INLET STRAINER ( 45d ONLY)
20
IL1612
603 p/n 76451 8773_8774 Owmers Manual
32
DESCRIPTION
SWITCH, MOMENTARY, BREW START
EXPLODED VIEW & PARTS LIST (continued)
CABINET COMPONENTS
IL1633a
ITEM
DESCRIPTION
USED ON
33
2I-70139
GASKET, SPRAY HEAD
8773, 8774
34
A6-72727
SPRAY DISK, EMBOSSED
8773, 8774
34a
A6-70163
RETAINER, SPRAY HEAD (REQUIRES DRILL/RIVETS TO INSTALL)
8773, 8774
70
2P-70053
BUTTON PLUG, 2”, METAL
8773, 8774
73
2A-71732
LEG ASSEMBLY, LEVELLING
8773, 8774
2K-70229
BUSHING, HEYCO (LARGE)
2K-41928
BUSHING, HEYCO (SMALL)
77
2P-70272
BUTTON PLUG
8774
104
2Q-75089
DOOR, SOLENOID ACCESS, PLASTIC
8773, 8774
75
105
108
603 p/n 76451 8773_8774 Owmers Manual
PART NO.
109
8773, 8774
2F-76666
POUR OVER ASSEMBLY, PLASTIC
8773, 8774
2D-70399
BASIN PAN, AUTOMATIC
8773
DD-75632
BASIN PAN, POUR-OVER
8774
2M-70376
LABEL, FRONT PANEL DECAL, AUTOMATIC
8773
2M-70404
LABEL, FRONT PANEL DECAL, POUR-OVER
8774
121
BODY & BASE ASSEMBLY
8773, 8774
122
PANEL, FRONT
8773, 8774
BOTTOM PLATE
8773, 8774
BASIN COVER
8773, 8774
8773, 8774
124
126
WS-8542-6
127
WS-8539WF-3
BASIN BODY ASSY INTEG/AIRTOP
2D-70234
BREW CHAMBER, BLACK PLASTIC
WS-8942-6
BREW CHAMBER, BROWN PLASTIC (OPTIONAL limited to stock on hand)
200
201
2D-70114
BREW CHAMBER, STAINLESS W/ WIRE BASKET (OPTIONAL)
WS-POF
FILTER PAPER, COFFEE (CASE OF 1000)
21
8773, 8774
8773, 8774
SERVICE KITS
SOLENOID REPAIR KITS
WS-85218
WS-85219
Inlet Fitting Kit (items 45a, 45b, 45c, 45d)
Inlet Strainer (item 45d)
IL1612
COMPLETE SPARE TANK COVER
WS-8541 WF-300 Spare Cover Assembly (120V, 1500W, 8773 (U.S. & Canada) With Coil - all parts mounted to cover)
WS-8543-300
Spare Cover Assembly (120V, 1500W, 8774 (U.S. & Canada) No Coil - all parts mounted to cover)
FAUCET REPAIR KITS
WS-82573
Handle (item 29a)
WS-82575
Seat Cup (item 29c)
WS-82576
Faucet Repair Kit (Includes 29a Handle, 29c Seat Cup,
29d Spring, 29h Stem, 29j Pin & 29k Bonnet
Retainer Clip (item 29b)
WS-82682
WS-84804
Aerator Replacement Kit (Includes 29e O-Ring,
29f Aerator Disk& 29g Aerator Cap
Aerator Repair Kit (Includes 29e O-Ring & 29f Aerator Disk)
WS-84870
IL1634
LINE STRAINER
“Y” Strainer, 1/4” Male Flare
IL1635
22
603 p/n 76451 8773_8774 Owmers Manual
2V-73027
603 p/n 76451 8773_8774 Owmers Manual
WIRING DIAGRAMS
23
WIRING DIAGRAMS (continued)
603 p/n 76451 8773_8774 Owmers Manual
2M-73651 (-)
24
603 p/n 76451 8773_8774 Owmers Manual
WIRING DIAGRAM (continued)
25
10 Sunnen Drive, St. Louis, MO 63143
telephone: 314-678-6336 fax: 314-781-2714
www.bloomfieldworldwide.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising