Impassa SCW9055-57 Installation Manual

Impassa SCW9055-57 Installation Manual
Self Contained Wireless Alarm System
Models:
SCW9055(D)(G)(I)-433/868
SCW9057(D)(G)(I)-433/868
Used with:
WT5500-433/868
WT5500(P)-433/868
v1.0 Installation Guide
WARNING: This manual contains information on limitations regarding product use and
function and information on the limitations as to liability of the manufacturer. The entire
manual should be carefully read.
WWW.DIYALARMFORUM.COM
WWW.DIYALARMFORUM.COM
Table of Contents
1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1 SCW9055/57 Model Differences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2 Compatible Wireless Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3 Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.4 Controls & Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.5 Data Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
2
3
3
2 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.1 Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2 Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.3 Wireless Device Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4 Alternate Communicator Module Setup/Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
6
7
9
3 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.1 Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2 Language Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3 [ ✱ ] Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.4 Function Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.5 System Removal Prevention . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
10
10
13
13
4 Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.1 Template Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.2 DLS Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4.3 Installer Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5 Advanced Programming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5.1 How to Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.2 Index to Programming Worksheets and Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.3 Programming Worksheets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.4 Programming Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18
19
20
40
6 Testing and Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Appendix A: Reporting Code Formats. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Appendix B: 2-Way Audio Verification (SCW9057 only) . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Appendix C: Communicator Format Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Appendix D: Regulatory Approvals Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
WWW.DIYALARMFORUM.COM
SAFETY INSTRUCTIONS for SERVICE PERSONNEL
WARNING: When using equipment connected to the TELEPHONE NETWORK, there are basic safety instructions that should always
be followed. Refer to the SAFETY INTRUCTIONS provided with this product; save them for (future) reference. Instruct the end-user
regarding the safety precautions that shall be observed when operating this equipment.
Before Installing The Equipment
Ensure your package includes the following items:
•
Installation and User Manuals, including the SAFETY INSTRUCTIONS.
READ and SAVE These Instructions!
Follow All WARNINGS AND INSTRUCTIONS specified within this document and/or on the equipment
•
SCW905x alarm controller
•
Power Supply, direct plug-in
•
Mounting hardware
Selecting A Suitable Location For The Alarm Controller
Use the following list as a guide to find a suitable place for this equipment:
•
Locate near a telephone socket and power outlet.
•
Select a place free from vibration and shocks.
•
Place the alarm controller on a flat, stable surface and follow the installation Instructions.
DO NOT locate this product where persons may walk on the secondary circuit cable(s).
DO NOT connect the alarm controller to electrical outlets on the same circuit as large appliances.
DO NOT select a place that exposes your alarm controller to direct sunlight, excessive heat, moisture, vapors, chemicals or dust.
DO NOT install this equipment near water. (e.g., bath tub, wash bowl, kitchen/laundry sink, wet basement, near a swimming
pool).
DO NOT install this equipment and its accessories in areas where there is a risk of explosion.
DO NOT connect this equipment to electrical outlets controlled by wall switches or automatic timers;
AVOID interference sources.
AVOID setting up the equipment near heaters, air conditioners, ventilators, and/or refrigerators.
AVOID locating this equipment close to or on top of large metal objects (e.g., metal wall studs).
SAFETY Precautions Required During Installation
•
•
•
•
•
NEVER install this equipment and/or telephone wiring during a lightning storm.
NEVER touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.
Position cables so that accidents can not occur. Connected cables must NOT be subject to excessive mechanical strain.
Use only the power supply provided with this equipment. Use of unauthorized power supplies may cause damage.
For direct plug-in versions, use the transformer supplied with the device.
WARNING:
THIS EQUIPMENT HAS NO MAINS ON/OFF SWITCH. THE PLUG OF THE DIRECT PLUG-IN POWER SUPPLY IS
INTENDED TO SERVE AS THE DISCONNECTING DEVICE IF THE EQUIPMENT MUST BE QUICKLY DISCONNECTED. IT
IS IMPERATIVE THAT ACCESS TO THE MAINS PLUG AND ASSOCIATED MAINS SOCKET/OUTLET IS NEVER
OBSTRUCTED.
IMPORTANT NOTE!
This Alarm System shall be installed and used within an
environment that provides the pollution degree max 2 and overvoltages category II NON-HAZARDOUS LOCATIONS, indoor
only. The equipment is DIRECT PLUG-IN (external transformer)
and is designed to be installed, serviced and/or repaired by
service persons only; [service person is defined as a person
having the appropriate technical training and experience
necessary to be aware of hazards to which that person may be
exposed in performing a task and of measures to minimize the
risks to that person or other persons]. There are no parts
replaceable by the end-user within this equipment. The wiring
(cables) used for installation of the Alarm System and
accessories, shall be insulated with PVC, TFE, PTFE, FEP,
Neoprene or Polyamide.
(a) The equipment enclosure must be secured to the building
structure before operation.
(b) Internal wiring must be routed in a manner that prevents:
- Excessive strain or loosening of wire on terminal
connections;
- Damage of conductor insulation
(c) Disposal of used batteries shall be made in accordance
with local waste recovery and recycling regulations.
(d) Before servicing, DISCONNECT the power and telephone
connection.
(e) DO NOT route any wiring over circuit boards.
(f) It is the installer’s responsibility to ensure that a readily
accessible disconnect device is incorporated in the building
for permanently connected installations.
The power supply must be Class II, FAIL SAFE with double or reinforced insulation between the PRIMARY and SECONDARY circuit/
ENCLOSURE and be an approved type acceptable to the local authorities. All national wiring rules shall be observed.
i
WWW.DIYALARMFORUM.COM
Guidelines for Locating Smoke & CO Detectors
The following information is for general guidance only and it is recommended that local fire codes and regulations be consulted when
locating and installing smoke and CO alarms.
Smoke Detectors
Research indicates that all hostile fires in homes generate smoke to a greater or lesser extent. Detectable quantities of smoke precede
detectable levels of heat in most cases. Smoke alarms should be installed outside of each sleeping area and on each storey of the home.
DSC recommends that additional smoke alarms beyond those required for minimum protection be installed. Additional areas that
should be protected include: the basement; bedrooms, especially where smokers sleep; dining rooms; furnace and utility rooms; and
any hallways not protected by the required units.
On smooth ceilings, detectors may be spaced 9.1m (30 feet) apart as a guide. Other spacing may be required depending on ceiling
height, air movement, the presence of joists, uninsulated ceilings, etc. Consult National Fire Alarm Code NFPA 72, CAN/ULC-S55302 or other appropriate national standards for installation recommendations.
•
Do not locate smoke detectors at the top of peaked or gabled ceilings; dead air space in these locations may prevent smoke detection.
•
Avoid areas with turbulent air flow, such as near doors, fans or windows. Rapid air movement around the detector may prevent
smoke from entering the unit.
•
Do not locate detectors in areas of high humidity.
•
Do not locate detectors in areas where the temperature rises above 38oC (100oF) or falls below 5oC (41oF).
Smoke detectors should always be installed in USA in accordance with Chapter 11 of NFPA 72, the National Fire Alarm Code:
11.5.1.1. Where required by applicable laws, codes, or standards for a specific type of occupancy, approved single- and multiple-station smoke alarms shall be installed as follows:
1. In all sleeping rooms and guest rooms.
2. Outside of each separate dwelling unit sleeping area, within 6.4 m (21 ft) of any door to a sleeping room, the distance measured
along a path of travel.
3. On every level of a dwelling unit, including basements.
4. On every level of a residential board and care occupancy (small facility), including basements and excluding crawl spaces and
unfinished attics.
5. In the living area(s) of a guest suite.
6. In the living area(s) of a residential board and care occupancy (small facility).
Figure 3a
Figure 4
Figure 3
Figure 1
Figure 2
CO Detectors
CO gas moves freely in the air. The human body is most vulnerable to the effects of CO gas during
sleeping hours. For maximum protection, a CO alarm should be located outside primary sleeping
areas or on each level of your home. Figure 5 indicates the suggested locations in the home. The
electronic sensor detects carbon monoxide, measures the concentration and sounds a loud alarm
before a potentially harmful level is reached.
Do NOT place the CO alarm in the following areas:
•
Where the temperature may drop below -10ºC or exceed 40 ºC.
•
Near paint thinner fumes.
•
Within 5 feet (1.5 meters) of open flame appliances such as furnaces, stoves and fireplaces.
•
In exhaust streams from gas engines, vents, flues or chimneys.
•
Do not place in close proximity to an automobile exhaust pipe; this will damage the detector.
ii
BEDROOM
BEDROOM
BEDROOM
GROUND
FLOOR
KITCHEN
GARAGE
BASEMENT
CARBON MONOXIDE DETECTOR
Figure 5
WWW.DIYALARMFORUM.COM
Limited Warranty
Digital Security Controls warrants the original purchaser that for a period of twelve months from the date of purchase, the product shall be free of defects in materials and
workmanship under normal use. During the warranty period, Digital Security Controls shall, at its option, repair or replace any defective product upon return of the product to
its factory, at no charge for labour and materials. Any replacement and/or repaired parts are warranted for the remainder of the original warranty or ninety (90) days, whichever
is longer. The original purchaser must promptly notify Digital Security Controls in writing that there is defect in material or workmanship, such written notice to be received in
all events prior to expiration of the warranty period. There is absolutely no warranty on software and all software products are sold as a user license under the terms of the
software license agreement included with the product. The Customer assumes all responsibility for the proper selection, installation, operation and maintenance of any
products purchased from DSC. Custom products are only warranted to the extent that they do not function upon delivery. In such cases, DSC can replace or credit at its option.
International Warranty
The warranty for international customers is the same as for any customer within Canada and the United States, with the exception that Digital Security Controls shall not be
responsible for any customs fees, taxes, or VAT that may be due.
Warranty Procedure
To obtain service under this warranty, please return the item(s) in question to the point of purchase. All authorized distributors and dealers have a warranty program. Anyone
returning goods to Digital Security Controls must first obtain an authorization number. Digital Security Controls will not accept any shipment whatsoever for which prior
authorization has not been obtained.
Conditions to Void Warranty
This warranty applies only to defects in parts and workmanship relating to normal use. It does not cover:
• damage incurred in shipping or handling;
• damage caused by disaster such as fire, flood, wind, earthquake or lightning;
• damage due to causes beyond the control of Digital Security Controls such as excessive voltage, mechanical shock or water damage;
• damage caused by unauthorized attachment, alterations, modifications or foreign objects;
• damage caused by peripherals (unless such peripherals were supplied by Digital Security Controls Ltd.);
• defects caused by failure to provide a suitable installation environment for the products;
• damage caused by use of the products for purposes other than those for which it was designed;
• damage from improper maintenance;
• damage arising out of any other abuse, mishandling or improper application of the products.
Items Not Covered by Warranty
In addition to the items which void the Warranty, the following items shall not be covered by Warranty: (i) freight cost to the repair centre; (ii) products which are not identified
with DSC's product label and lot number or serial number; (iii) products disassembled or repaired in such a manner as to adversely affect performance or prevent adequate
inspection or testing to verify any warranty claim. Access cards or tags returned for replacement under warranty will be credited or replaced at DSC's option. Products not
covered by this warranty, or otherwise out of warranty due to age, misuse, or damage shall be evaluated, and a repair estimate shall be provided. No repair work will be
performed until a valid purchase order is received from the Customer and a Return Merchandise Authorization number (RMA) is issued by DSC's Customer Service.
Digital Security Controls Ltd.’s liability for failure to repair the product under this warranty after a reasonable number of attempts will be limited to a replacement of the product,
as the exclusive remedy for breach of warranty. Under no circumstances shall Digital Security Controls be liable for any special, incidental, or consequential damages based
upon breach of warranty, breach of contract, negligence, strict liability, or any other legal theory. Such damages include, but are not limited to, loss of profits, loss of the
product or any associated equipment, cost of capital, cost of substitute or replacement equipment, facilities or services, down time, purchaser’s time, the claims of third
parties, including customers, and injury to property. The laws of some jurisdictions limit or do not allow the disclaimer of consequential damages. If the laws of such a
jurisdiction apply to any claim by or against DSC, the limitations and disclaimers contained here shall be to the greatest extent permitted by law. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so that the above may not apply to you.
Disclaimer of Warranties
This warranty contains the entire warranty and shall be in lieu of any and all other warranties, whether expressed or implied (including all implied warranties of merchantability
or fitness for a particular purpose) and of all other obligations or liabilities on the part of Digital Security Controls. Digital Security Controls neither assumes responsibility for,
nor authorizes any other person purporting to act on its behalf to modify or to change this warranty, nor to assume for it any other warranty or liability concerning this product.
This disclaimer of warranties and limited warranty are governed by the laws of the province of Ontario, Canada.
WARNING: Digital Security Controls recommends that the entire system be completely tested on a regular basis. However, despite frequent
testing, and due to, but not limited to, criminal tampering or electrical disruption, it is possible for this product to fail to perform as expected.
Out of Warranty Repairs
Digital Security Controls will at its option repair or replace out-of-warranty products which are returned to its factory according to the following conditions. Anyone returning
goods to Digital Security Controls must first obtain an authorization number. Digital Security Controls will not accept any shipment whatsoever for which prior authorization has
not been obtained.
Products which Digital Security Controls determines to be repairable will be repaired and returned. A set fee which Digital Security Controls has predetermined and which may
be revised from time to time, will be charged for each unit repaired.
Products which Digital Security Controls determines not to be repairable will be replaced by the nearest equivalent product available at that time. The current market price of
the replacement product will be charged for each replacement unit.
WARNING - READ CAREFULLY
Note to Installers
This warning contains vital information. As the only individual in contact with system users, it is your responsibility to bring each item in this warning to the attention of the
users of this system.
System Failures
This system has been carefully designed to be as effective as possible. There are circumstances, however, involving fire, burglary, or other types of emergencies where it may
not provide protection. Any alarm system of any type may be compromised deliberately or may fail to operate as expected for a variety of reasons. Some but not all of these
reasons may be:
• Inadequate Installation
A security system must be installed properly in order to provide adequate protection. Every installation should be evaluated by a security professional to ensure that all access
points and areas are covered. Locks and latches on windows and doors must be secure and operate as intended. Windows, doors, walls, ceilings and other building materials
must be of sufficient strength and construction to provide the level of protection expected. A reevaluation must be done during and after any construction activity. An evaluation
by the fire and/or police department is highly recommended if this service is available.
• Criminal Knowledge
This system contains security features which were known to be effective at the time of manufacture. It is possible for persons with criminal intent to develop techniques which
reduce the effectiveness of these features. It is important that a security system be reviewed periodically to ensure that its features remain effective and that it be updated or
replaced if it is found that it does not provide the protection expected.
• Access by Intruders
Intruders may enter through an unprotected access point, circumvent a sensing device, evade detection by moving through an area of insufficient coverage, disconnect a
warning device, or interfere with or prevent the proper operation of the system.
• Power Failure
Control units, intrusion detectors, smoke detectors and many other security devices require an adequate power supply for proper operation. If a device operates from batteries,
it is possible for the batteries to fail. Even if the batteries have not failed, they must be charged, in good condition and installed correctly. If a device operates only by AC power,
any interruption, however brief, will render that device inoperative while it does not have power. Power interruptions of any length are often accompanied by voltage
fluctuations which may damage electronic equipment such as a security system. After a power interruption has occurred, immediately conduct a complete system test to
ensure that the system operates as intended.
• Failure of Replaceable Batteries
This system’s wireless transmitters have been designed to provide several years of battery life under normal conditions. The expected battery life is a function of the device
environment, usage and type. Ambient conditions such as high humidity, high or low temperatures, or large temperature fluctuations may reduce the expected battery life.
While each transmitting device has a low battery monitor which identifies when the batteries need to be replaced, this monitor may fail to operate as expected. Regular testing
and maintenance will keep the system in good operating condition.
• Compromise of Radio Frequency (Wireless) Devices
Signals may not reach the receiver under all circumstances which could include metal objects placed on or near the radio path or deliberate jamming or other inadvertent
radio signal interference.
• System Users
A user may not be able to operate a panic or emergency switch possibly due to permanent or temporary physical disability, inability to reach the device in time, or unfamiliarity
with the correct operation. It is important that all system users be trained in the correct operation of the alarm system and that they know how to respond when the system
indicates an alarm.
• Smoke Detectors
Smoke detectors that are a part of this system may not properly alert occupants of a fire for a number of reasons, some of which follow. The smoke detectors may have been
improperly installed or positioned. Smoke may not be able to reach the smoke detectors, such as when the fire is in a chimney, walls or roofs, or on the other side of closed
doors. Smoke detectors may not detect smoke from fires on another level of the residence or building.
Every fire is different in the amount of smoke produced and the rate of burning. Smoke detectors cannot sense all types of fires equally well. Smoke detectors may not provide
timely warning of fires caused by carelessness or safety hazards such as smoking in bed, violent explosions, escaping gas, improper storage of flammable materials,
overloaded electrical circuits, children playing with matches or arson.
Even if the smoke detector operates as intended, there may be circumstances when there is insufficient warning to allow all occupants to escape in time to avoid injury or death.
• Motion Detectors
Motion detectors can only detect motion within the designated areas as shown in their respective installation instructions. They cannot discriminate between intruders and
intended occupants. Motion detectors do not provide volumetric area protection. They have multiple beams of detection and motion can only be detected in unobstructed
areas covered by these beams. They cannot detect motion which occurs behind walls, ceilings, floor, closed doors, glass partitions, glass doors or windows. Any type of
tampering whether intentional or unintentional such as masking, painting, or spraying of any material on the lenses, mirrors, windows or any other part of the detection system
will impair its proper operation.
Passive infrared motion detectors operate by sensing changes in temperature. However their effectiveness can be reduced when the ambient temperature rises near or above
body temperature or if there are intentional or unintentional sources of heat in or near the detection area. Some of these heat sources could be heaters, radiators, stoves,
barbeques, fireplaces, sunlight, steam vents, lighting and so on.
• Warning Devices
Warning devices such as sirens, bells, horns, or strobes may not warn people or waken someone sleeping if there is an intervening wall or door. If warning devices are located
on a different level of the residence or premise, then it is less likely that the occupants will be alerted or awakened. Audible warning devices may be interfered with by other
noise sources such as stereos, radios, televisions, air conditioners or other appliances, or passing traffic. Audible warning devices, however loud, may not be heard by a
hearing-impaired person.
• Telephone Lines
If telephone lines are used to transmit alarms, they may be out of service or busy for certain periods of time. Also an intruder may cut the telephone line or defeat its operation
by more sophisticated means which may be difficult to detect.
• Insufficient Time
There may be circumstances when the system will operate as intended, yet the occupants will not be protected from the emergency due to their inability to respond to the
warnings in a timely manner. If the system is monitored, the response may not occur in time to protect the occupants or their belongings.
• Component Failure
Although every effort has been made to make this system as reliable as possible, the system may fail to function as intended due to the failure of a component.
• Inadequate Testing
Most problems that would prevent an alarm system from operating as intended can be found by regular testing and maintenance. The complete system should be tested
weekly and immediately after a break-in, an attempted break-in, a fire, a storm, an earthquake, an accident, or any kind of construction activity inside or outside the premises.
The testing should include all sensing devices, keypads, consoles, alarm indicating devices and any other operational devices that are part of the system.
•Security and Insurance
Regardless of its capabilities, an alarm system is not a substitute for property or life insurance. An alarm system also is not a substitute for property owners, renters, or other
occupants to act prudently to prevent or minimize the harmful effects of an emergency situation.
IMPORTANT - READ CAREFULLY: DSC Software purchased with or without Products and Components
is copyrighted and is purchased under the following license terms:
• This End-User License Agreement (“EULA”) is a legal agreement between You (the company, individual or entity who acquired the Software and any
related Hardware) and Digital Security Controls, a division of Tyco Safety Products Canada Ltd. (“DSC”), the manufacturer of the integrated security
systems and the developer of the software and any related products or components (“HARDWARE”) which You acquired.
• If the DSC software product (“SOFTWARE PRODUCT” or “SOFTWARE”) is intended to be accompanied by HARDWARE, and is NOT accompanied by
new HARDWARE, You may not use, copy or install the SOFTWARE PRODUCT. The SOFTWARE PRODUCT includes computer software, and may
include associated media, printed materials, and “online” or electronic documentation.
• Any software provided along with the SOFTWARE PRODUCT that is associated with a separate end-user license agreement is licensed to You under the
terms of that license agreement.
• By installing, copying, downloading, storing, accessing or otherwise using the SOFTWARE PRODUCT, You agree unconditionally to be bound by the
terms of this EULA, even if this EULA is deemed to be a modification of any previous arrangement or contract. If You do not agree to the terms of this
EULA, DSC is unwilling to license the SOFTWARE PRODUCT to You, and You have no right to use it.
SOFTWARE PRODUCT LICENSE
The SOFTWARE PRODUCT is protected by copyright laws and international copyright treaties, as well as other intellectual property laws and treaties. The
SOFTWARE PRODUCT is licensed, not sold.
1.GRANT OF LICENSE This EULA grants You the following rights:
(a) Software Installation and Use - For each license You acquire, You may have only one copy of the SOFTWARE PRODUCT installed.
(b) Storage/Network Use - The SOFTWARE PRODUCT may not be installed, accessed, displayed, run, shared or used concurrently on or from different
computers, including a workstation, terminal or other digital electronic device (“Device”). In other words, if You have several workstations, You will
have to acquire a license for each workstation where the SOFTWARE will be used.
(c) Backup Copy - You may make back-up copies of the SOFTWARE PRODUCT, but You may only have one copy per license installed at any given time.
You may use the back-up copy solely for archival purposes. Except as expressly provided in this EULA, You may not otherwise make copies of the
SOFTWARE PRODUCT, including the printed materials accompanying the SOFTWARE.
2. DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS
(a) Limitations on Reverse Engineering, Decompilation and Disassembly - You may not reverse engineer, decompile, or disassemble the SOFTWARE
PRODUCT, except and only to the extent that such activity is expressly permitted by applicable law notwithstanding this limitation. You may not make any
changes or modifications to the Software, without the written permission of an officer of DSC. You may not remove any proprietary notices, marks or
labels from the Software Product. You shall institute reasonable measures to ensure compliance with the terms and conditions of this EULA.
(b) Separation of Components - The SOFTWARE PRODUCT is licensed as a single product. Its component parts may not be separated for use on more
than one HARDWARE unit.
(c) Single INTEGRATED PRODUCT - If You acquired this SOFTWARE with HARDWARE, then the SOFTWARE PRODUCT is licensed with the HARDWARE
as a single integrated product. In this case, the SOFTWARE PRODUCT may only be used with the HARDWARE as set forth in this EULA.
(d) Rental - You may not rent, lease or lend the SOFTWARE PRODUCT. You may not make it available to others or post it on a server or web site.
(e) Software Product Transfer - You may transfer all of Your rights under this EULA only as part of a permanent sale or transfer of the HARDWARE,
provided You retain no copies, You transfer all of the SOFTWARE PRODUCT (including all component parts, the media and printed materials, any
upgrades and this EULA), and provided the recipient agrees to the terms of this EULA. If the SOFTWARE PRODUCT is an upgrade, any transfer must
also include all prior versions of the SOFTWARE PRODUCT.
(f) Termination - Without prejudice to any other rights, DSC may terminate this EULA if You fail to comply with the terms and conditions of this EULA.
In such event, You must destroy all copies of the SOFTWARE PRODUCT and all of its component parts.
(g) Trademarks - This EULA does not grant You any rights in connection with any trademarks or service marks of DSC or its suppliers.
3. COPYRIGHT - All title and intellectual property rights in and to the SOFTWARE PRODUCT (including but not limited to any images, photographs, and
text incorporated into the SOFTWARE PRODUCT), the accompanying printed materials, and any copies of the SOFTWARE PRODUCT, are owned by DSC
or its suppliers. You may not copy the printed materials accompanying the SOFTWARE PRODUCT. All title and intellectual property rights in and to the
content which may be accessed through use of the SOFTWARE PRODUCT are the property of the respective content owner and may be protected by
applicable copyright or other intellectual property laws and treaties. This EULA grants You no rights to use such content. All rights not expressly granted
under this EULA are reserved by DSC and its suppliers.
4. EXPORT RESTRICTIONS - You agree that You will not export or re-export the SOFTWARE PRODUCT to any country, person, or entity subject to
Canadian export restrictions.
5. CHOICE OF LAW - This Software License Agreement is governed by the laws of the Province of Ontario, Canada.
6. ARBITRATION - All disputes arising in connection with this Agreement shall be determined by final and binding arbitration in accordance with the
Arbitration Act, and the parties agree to be bound by the arbitrator’s decision. The place of arbitration shall be Toronto, Canada, and the installation
manual of the arbitration shall be English.
7. LIMITED WARRANTY
(a) NO WARRANTY - DSC PROVIDES THE SOFTWARE “AS IS” WITHOUT WARRANTY. DSC DOES NOT WARRANT THAT THE SOFTWARE WILL MEET YOUR
REQUIREMENTS OR THAT OPERATION OF THE SOFTWARE WILL BE UNINTERRUPTED OR ERROR-FREE.
(b) CHANGES IN OPERATING ENVIRONMENT - DSC shall not be responsible for problems caused by changes in the operating characteristics of the
HARDWARE, or for problems in the interaction of the SOFTWARE PRODUCT with non-DSC-SOFTWARE or HARDWARE PRODUCTS.
(c) LIMITATION OF LIABILITY; WARRANTY REFLECTS ALLOCATION OF RISK - IN ANY EVENT, IF ANY STATUTE IMPLIES WARRANTIES OR CONDITIONS
NOT STATED IN THIS LICENSE AGREEMENT, DSC’S ENTIRE LIABILITY UNDER ANY PROVISION OF THIS LICENSE AGREEMENT SHALL BE LIMITED
TO THE GREATER OF THE AMOUNT ACTUALLY PAID BY YOU TO LICENSE THE SOFTWARE PRODUCT AND FIVE CANADIAN DOLLARS (CAD$5.00).
BECAUSE SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL
DAMAGES, THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
(d) DISCLAIMER OF WARRANTIES - THIS WARRANTY CONTAINS THE ENTIRE WARRANTY AND SHALL BE IN LIEU OF ANY AND ALL OTHER
WARRANTIES, WHETHER EXPRESSED OR IMPLIED (INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE) AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON THE PART OF DSC. DSC MAKES NO OTHER WARRANTIES. DSC
NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON PURPORTING TO ACT ON ITS BEHALF TO MODIFY OR TO CHANGE THIS WARRANTY,
NOR TO ASSUME FOR IT ANY OTHER WARRANTY OR LIABILITY CONCERNING THIS SOFTWARE PRODUCT.
(e) EXCLUSIVE REMEDY AND LIMITATION OF WARRANTY - UNDER NO CIRCUMSTANCES SHALL DSC BE LIABLE FOR ANY SPECIAL, INCIDENTAL,
CONSEQUENTIAL OR INDIRECT DAMAGES BASED UPON BREACH OF WARRANTY, BREACH OF CONTRACT, NEGLIGENCE, STRICT LIABILITY, OR
ANY OTHER LEGAL THEORY. SUCH DAMAGES INCLUDE, BUT ARE NOT LIMITED TO, LOSS OF PROFITS, LOSS OF THE SOFTWARE PRODUCT OR
ANY ASSOCIATED EQUIPMENT, COST OF CAPITAL, COST OF SUBSTITUTE OR REPLACEMENT EQUIPMENT, FACILITIES OR SERVICES, DOWN
TIME, PURCHASERS TIME, THE CLAIMS OF THIRD PARTIES, INCLUDING CUSTOMERS, AND INJURY TO PROPERTY.
WARNING: DSC recommends that the entire system be completely tested on a regular basis. However, despite frequent testing, and
due to, but not limited to, criminal tampering or electrical disruption, it is possible for this SOFTWARE PRODUCT to fail to perform as
expected.
iii
WWW.DIYALARMFORUM.COM
1.1 SCW9055/57 Model Differences
1 Introduction
This manual provides installation and programming information for the SCW9055(D)(G)(I) and SCW9057(D)(G)(I) two-way wireless alarm system. Available hardware platforms for the 433 MHz and 868 MHz versions are described below.
1.1 SCW9055/57 Model Differences
• SCW9057 includes all of the features of the SCW9055 plus the addition of 2-way audio.
• “D” models include a TL2553G or TL255GS alternate communicator module. These modules combine 3G or GSM with TCP/IP Ethernet/
Internet communications. Either function can be programmed as the primary or backup communicator.
• “G” models include a 3G2055 or GS2055 alternate communicator module. The 3G2055 is a 3G wireless cellular communicator. The
GS2055 is a GSM wireless cellular communicator. Either module can be programmed as the primary or backup communicator.
• “I” models include a TL255 alternate communicator module. The TL255 is an Ethernet/Internet communicator that can be programmed as the
primary or backup communicator.
Table 1-1 SCW9055/57 Models
Model
(SCW9055/57)
-433
-868
D-433
D-868
G-433
G-868
I-433
I-868
Frequency
(MHZ)
TL2553G
(D)
TL255GS
(D)
3G2055
(G)
GS2055
(G)
TL255
(I)
433.92
868.35
433.92
868.35
433.92
868.35
433.92
868.35
✖
✖
✔
✔
✖
✖
✖
✖
✖
✖
✔
✔
✖
✖
✖
✖
✖
✖
✖
✖
✔
✔
✖
✖
✖
✖
✖
✖
✔
✔
✖
✖
✖
✖
✖
✖
✖
✖
✔
✔
NOTE:
All models can communicate via phone line (PSTN) in addition to
3G or GSM cellular and Internet as described above. Refer to the
associated installation guide for information on programming the
communicator modules.
NOTE:
Only models SCW9055-433, SCW9055G-433, SCW9055D433, SCW9055I-433, SCW9057-433, SCW9057G-433,
SCW9057D-433, SCW9057I-433 are UL/ULC listed.
1.2 Compatible Wireless Devices
The table below lists all wireless devices compatible with the SCW9055/57 alarm panel.
Table 1-2 Compatible Wireless Devices
Table 1-3 Out of the Box
WS, WLS, EV = 1-way wireless device. WT = 2-way wireless device.
Descriptions
SCW9055/57-433
SCW9055/57-868
Wireless Keypads
ULWT5500-433
WT5500-868
WT5500P-868
Proximity Tag
ULPT4
PT8
1- Way Wireless Repeater
ULWS4920
WS8920
Door Contacts
ULWS4945
WS8945
WS8965
WS8975
ULWT5500P-433
UL
WS4965
**WS4975
EV-DW4917
EV-DW4955
***EV-DW4975
UL
WS4904
WS4904P
ULWLS914-433
WS8904
WS8904P
ULWS4916
WS8916
Carbon Monoxide Detector ULWS4913
WS8913
Motion Detectors
UL
Smoke Detector
ULWS4926
Flood Detector
WS4985
Glass Break Detectors
ULWLS912L-433
Shock Detector
EV-DW4927
Wireless
Sirens
Indoor ULWT4901
Outdoor ULWT4911
WT8901
WT8911
ULWS4939
WS8939
WT8989
UL
WS4938
WS4938-2W
WS8938
Wireless Keys
WS4949
WS4959
WS4969
WS4979
UL
WT4989
Panic Pendants
Hold-up
WLS928-433
2-way Wireless Integration
module
IT-410
SCW9055/57 alarm panel
Mounting hardware kit
Installation & User manuals Qty (1) ea.
One-way, Two-way Device installation sheets as required
Table 1-4 Enclosures
The SCW9055/57 main board and keypad are installed in a plastic enclosure.
Tamper protection switches are installed on the enclosure, including cover
opening protection and or removal from the mounting position. The enclosure
top cover can only be removed using a flat screwdriver.
Table 1-5 Dimensions:
227mm (L) x 141mm (W) x 42mm (D)
WT5500 (including wall bracket):
125mm (L) x 165mm (W) x 38mm (D)
Compatible Receivers: SG-System I, SG-System II,SG-System III and
SG-System IV.
Only UL approved devices are to be used with UL/ULC listed systems.
** Not available in North America, South America and New Zealand
***Available in North America, South America and New Zealand only
Note: For SIA CP-01 compliant installations, the minimum required
components are: SCW9055-433 or SCW9057-433 Control Panel.
Optional components that can be used with the system are: TL255,
TL2553G, TL255GS, 3G2055, GS2055, WT5500(P)-433, PT4,
WT4901, and WT4911.
Note: For SIA CP-01 installations, key fobs (WS4939, WS4938 and
WT4989) cannot be used for panic/alarm functionality, only for Arming and Disarming functions.
WWW.DIYALARMFORUM.COM
1
SCW9055/57 Wireless Alarm System
1.3 Product Specifications
Control and Indicating Equipment Specifications
Zone Configuration
• 32 Wireless zones supported and 2 hardwired zones available
on the main board
• 28 zone types, 13 programmable zone attributes
• Zone configurations available: normally closed, single EOL
and DEOL supervised
• 1 separate wireless keypad supported: model WT5500 or
WT5500P (433MHz or 868MHz)
• 16 separate remote access key supported: model WT4989/
WT8989, WS4939/WS8939, WS4949, WS4959, WS4969
• With WT5500P keypad, 16 separate proximity tags supported:
model PT4/PT8
Access Codes
• Up to 16 access codes: 16 (level 2), one system master code
(level 3), one installer code (level 3), and one maintenance code
• Programmable attributes for each user code (see SCW9055/57
User Guide for details)
• 58823 access code variations (6-digit codes) for each user code
Warning Device output
• Integral sounder supported capable of 85 dB @ 3m
• 2 remote, wireless indoor/outdoor warning devices supported,
models WT4901/WT4911 or WT8901/WT8911
• Programmable as steady, pulsed or temporal three (as per
ISO8201) and temporal four (CO alarm) output
• Fire and CO alarm notifications have priority over burglary
alarm notification.
Memory
• CMOS EEPROM memory
• Retains programming and system status on AC or battery failure
• Data Retention: 20 years min.
Programmable Outputs (PGMs)
• Up to 2 programmable outputs (PGM) with 13 options
• PGM outputs are open collector type and switched to ground,
rated max. 50mA
Power Supply
• Regulated, supervised and integral to the control unit
• Type A as per EN50131-6 Standard
• Input ratings: 16.5VAC/20VA (Min.) @50/60Hz, 100mA
• Current Draw:
240 VAC Primary . . . . . . . . . . . . . . . . . . . . 100mA(AC)(Max)
120 VAC Primary . . . . . . . . . . . . . . . . . . . . 100mA(AC)(Max)
16.5 VAC Secondary . . . . . . . . . . . . . . . . . 160mA(AC)(Max)
• Plug-in transformer included
• Connected, protected by fuse in primary circuit. For EU, rated
160mA/250VAC. For NA, rated 114mA/120VAC
• Transformer secondary ratings: 16VAC, 20VA min.
• AUX Output Voltage: 12VDC, -15%/+15% when AC Input
Voltage is 85% to +110% of rated value
• Aux max. draw is 100mA
• Output ripple voltage: 150mVp-p max.
• Storage device: NiMH, rechargeable battery, rated 7.2VDC
(nominal)
• Battery capacity:
DSC part no. 17000145 . . . . . . . . . . . . . . . . . . . . . . . . . 1.5Ah
DSC part no. 17000152 . . . . . . . . . . . . . . . . . . . . . . . . . 3.6Ah
• Note: 17000145 for use with SCW9055/57 models. 17000152
for use with SCW9055/57 G, D, and I models.
2
• Maximum standby time 24h (AUX=0mA)/ 4h (AUX=100mA)
• Recharging time to 80% 24hours
• Recharging current:
DSC part no. 17000152 (1.5Ah) . . . . . . . . . . . . . . . . 125mA
DSC part no. 17000145 (3.6Ah) . . . . . . . . . . . . . . . . 250mA
• Low battery trouble indication threshold 7.2VDC
• Low Battery Trouble Restore Threshold 7.6VDC
• Battery deep discharge protection (cut-off at 6VDC)
• Main board current draw (battery only):
SCW9055/57 (no alternate communicator)
Standby . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .160mA DC
SCW9055/57 D,G, I, SM (including alternate communicator)
Standby . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .190mA DC
Transmit (alternate communicator module) . . . . .195mA DC
• Resettable fuses (PTC) used on circuit board instead of replaceable fuses
• Supervision for loss of primary power source (AC Fail), battery
fail or battery low voltage (Battery Trouble) with indication
provided on the keypad
• Internal clock locked to AC power frequency
Operating Environmental Conditions
• Temperature range: -10°C to +55°C (14°F-131°F)
• Relative humidity: 93% non condensing
Note: UL/ULC tested for 0°C to +49°C (32°F to 122°F), 85%R.H.
Alarm Transmitter Equipment (ATE) Specification
• Digital dialer integral to the main control board
• Supports all major formats: SIA, Contact ID, 20BPS and Residential Dial
• Optional Dual IP/Cellular communication modules [model “D”
and “D-SM” (NA only)], 3G or GSM only [model “G” and “GSM” (NA only)] or IP only [model “I” and “I-SM” (NA only)]
can be installed in the same enclosure and can be configured as
primary communicator or back-up, with AES128 bit encryption
for higher line security applications.
System Supervision Features
The SCW9055/57 continuously monitors a number of possible
trouble conditions and provides audible and visual indication at
the keypad. Multiple signals are indicated using scroll buttons on
the LCD keypads (no priority assigned).
Additional Features
• Automatic inhibit (swinger shutdown) for Alarm, Tamper,
Trouble signals after 3 occurrences in a given set period (see
section [377]), Opt [1] alarms, [2] tampers, [3] troubles
• Programmable keypad lockout option (see section [012])
• 500 Event Buffer, date and time stamped
WWW.DIYALARMFORUM.COM
1.4 Controls & Indicators
1.4 Controls & Indicators
The SCW9055/57 has four status indicators located on the front right side of the panel. See the table below for details:
Table 1-6 Controls & Indicators - Alarm Panel
Alarm Indicators
Ready: Panel is ready to be armed.
Armed: Panel is armed.
Trouble: Enter [][2] to view troubles.
Yellow indicates trouble. Orange indicates RF Jam trouble.
AC Power: On=AC present. OFF=AC absent.
Figure 1-1 Controls & Indicators - Keypad
2x16 LCD
< > indicates user can
scroll through options
System is
Ready to Arm
<>
Scroll Keys
Emergency Keys:
Fire
Auxiliary
Panic
1
2
3
4
5
6
7
8
9
*
0
#
LED Indicators
Ready
Armed
Trouble
Power
Function Keys:
Stay Arm
Away Arm
Chime
Bypass Zones OX
Quick Exit
Select Option
Previous Screen
1.5 Data Entry
Conventions Used in this manual
Brackets [ ] indicate numbers or symbols that must be entered on the keypad.
e.g., [ ✱ ][8][Installer Code][898] requires the following key entries:
.
[ ✱ ] indicates to the alarm system that a special command will be entered.
[8] places the alarm system in Installer Programming mode.
[5555] is the default installer code. The default installer code should be changed during initial programming of the system.
[898] indicates the particular programming section being accessed. e.g. [898] Wireless Device Enrollment, [899] Template Programming, [999] Alarm System Default.
Special Keys:
Scroll symbols < > on the display indicate that options can viewed by pressing the
used to position the cursor.
keys. These scroll keys can also be
The , key is similar in function to the “ENTER” key on a personal computer. It is generally used to accept the existing programming
option. It is also the first key entry for [ ✱ ] commands and can be used to enter the letters A-F when in Installer Programming mode.
The
key functions similarly to the “ESC” (escape) key on a personal computer. It is generally used to exit the current programming section or to return to the previous menu.
Entering Letters
1.
2.
3.
In Installer Programming, enter the section you want to add text to (usually a system label).
Use the arrow keys [<][>] to move the cursor to the letter you want to change.
Press the number key corresponding to the letter you require. Each number button accesses three letters and a number. The first
press of the number key displays the first letter. The second press displays the second letter, etc.
1
A, B, C, 1
2
D, E, F, 2
3
G, H, I, 3
4
J, K, L, 4
5
M, N, O, 5
6
P, Q, R, 6
7
S, T, U, 7
8
V, W, X, 8
9
Y, Z, 9,0
0
Space
4.
To select lower case letters press [*], scroll to “lower case” and press [*] again to select.
WWW.DIYALARMFORUM.COM
3
SCW9055/57 Wireless Alarm System
5.
6.
7.
When the required letter or number is displayed use the arrow keys [<][>] to scroll to the next letter.
When you are finished programming the Zone Label, press the [] key, use the [<][>] keys to scroll to “Save” then press [].
Continue from Step 2 until all labels are programmed.
Entering ASCII Characters
To enter ASCII characters, press [], scroll to “ASCII Entry” then press [] to select. Enter the corresponding three-digit number and
press [] to save and exit.
!
“
#
$
%
&
‘
(
)
*
+
,
-
.
/
0
1
2
3
4
5
6
7
8
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
9
:
;
<
=
>
?
@
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
Q
R
S
T
U
V
W
X
Y
Z
[
¥
]
^
_
╲
a
b
c
d
e
f
g
h
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
i
j
k
l
m
n
o
p
q
r
s
t
u
v
w
x
y
z
{
‫׀‬
}
⃗
⃖
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
□ 「 」 ֻ
▪
ヲ
ア
ィ
ゥ
ェ
ォ
カ
ュ
ョ
シ
ᅳ
ア
イ
ゥ
ェ
ォ
カ
161
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
162
163
164
160
キ ク
183
184
ケ コ サ シ ス セ ソ タ ダ ツ テ ト ナ ニ ヌ ネ ノ ハ ヒ フ ヘ ホ マ ミ
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
ム メ モ ヤ ユ ョ ラ リ ル レ ロ ワ ン ゙ ▢ α
ä
β Ɛ μ σ ρ
ϧ
ʃ
209
225
226
230
231
232
254
255
⊣
233
210
211
212
213
214
215
216
217
218
219
220
221
222
223
ϳ x ¢ £ ñ Ö p q θ œ Ω ϋ Σ π
234
235
236
237
238
239
240
241
242
243
244
245
246
247
224
X
248
227
228
229
y 千 Ⴌ Ħ ÷
249
250
251
252
253
▆
Incorrect Data Entries
To change a data entry before it has been accepted by the alarm system, use the scroll keys to reposition the cursor then re-enter the
digit. If the data has already been accepted, press [#] to exit the section then re-enter the programming section and type the data again.
If you incorrectly enter 0001 in Step 2 of Program alarm system in Template Programming, you must either reset the alarm system to
its default values (section [996], re-enroll all wireless devices and re-program the system) or re-enter the correct data in Installer Programming [ ✱ ][8].
Selecting Programming Options
To turn a programming option on or off, enter a programming section through Installer Programming. 8 spaces are displayed, each representing a separate programming option. Press the number corresponding to the option you want to activate/deactivate. Activated programming options display the option number. Deactivated options display a dash.
e.g.
Toggle Option
12- - - -7In the above example, programming options 1, 2, and 7 are on.
4
WWW.DIYALARMFORUM.COM
2 Installation
2 Installation
This section describes how to install and connect the SCW9055/57.
2.1 Mounting
1.
2.
3.
Figure -1, Opening Cover
If required, separate the front and back covers by removing
the cover screw then inserting a small slotted screwdriver
between the front and back covers and gently twist the
screwdriver to separate.
Route Telephone line wiring, I/O Wiring, and AC power
through the cutout in the back cover (see Fig. 2 Mounting &
Wiring details). If Programming with DLS, see “4.2.1 Local
Programming with PC-Link” on page 17. If using Template
programming or Advanced Keypad programming, continue
to the next step.
Secure the back cover to the wall with the hardware provided. See figure 2, Mounting & Wiring Details for hole
locations.
NOTE: If mounting unit on a double-ganged box with the
wall tamper feature, secure the back plate to the right
side of the ganged box using the center mounting
holes. This provides the tamper switch with unobstructed access to the wall surface.
Remove cover screw
Insert screwdriver in slots indicated.
Gently pry open cover with screwdriver
until cover separates.
Figure -2, Mounting & Wiring Details
4.
5.
6.
7.
8.
Connect wiring to the terminals indicated. See Section “2.2
Wiring” on page 6 for details.
NOTE: Do NOT apply power until wiring is completed.
Connect battery cable connector to the PC Board.
NOTE: Ensure connector key is oriented correctly.
Position the cover onto the back plate. Ensure tamper switch,
if used, is positioned correctly.
Insert cover in the top edge of the back plate at a 35° to 55°
angle then snap cover in place.
Apply power to the system.
SCW9055/57
Wiring Access
Mounting Hole
Mounting Holes
Battery Retainer
Battery
Once the system is wired and mounted, do the following:
•
Enroll devices. Enter [*][8][Installer Code][898]. See “2.3
Wireless Device Setup” on page 7.
•
If performing Template programming, enter [*][8][Installer
Code][899]. See “4.1 Template Programming” on page 14.
NOTE:
• See DLS Programming on page 17 for reprogramming an
existing Installation.
• AC Power must be present for the alarm system to answer
incoming calls from DLS. After the initial installation 24
Hrs. is required to fully charge the standby battery.
Wall and Case
Tamper Switch
Cover screw hole
Mounting Hole
Surface Mount
Wiring Access
AC Power
AC
AC
12 VDC
PGM/Zones
+ Aux -
1 I/O 2
Telephone Line
Ring
Tip
R-1
T-1
Red
Grn
Gra
Brn
SCW 9055/57 ( G, I, D Models)
Mounting Holes (4)
Communicator
Module
Wiring Access
Battery
Cover screw hole
Surface Mount
Wiring Access
AC Power
AC
AC
12 VDC
+ Aux -
PGM/Zones
1 I/O 2
amper Switch
Case Tamper
Telephone Line
Ring
Tip
R-1
T-1
Red
Grn
Gra
Brn
WWW.DIYALARMFORUM.COM
5
SCW9055/57 Wireless Alarm System
2.2 Wiring
2.2.1. Zone Wiring
Zones can be wired for Normally Open and Normally Closed contacts with Single-end-of-line (SEOL) resistors or Double End-ofLine (DEOL) resistors. Observe the following guidelines:
•
For UL/ULC listed installations use SEOL or DEOL only
•
Minimum 22 AWG wire, maximum 18 AWG
•
Do NOT use shielded wire
•
Wire run resistance shall not exceed 100Refer to the chart
below.
Normally Closed Loops - Do NOT use for UL Installations
Any I/O
Terminal
Max wire length to end-of-line resistor
(feet/meters)
22
3000 / 914
20
4900 / 1493
19
6200 / 1889
18
7800 / 2377
AUXTerminal
1 NORMALLY CLOSED
CONTACT WITH
NO END OF LINE
RESISTOR
Single End-of-Line (SEOL) Resistor Wiring
Any I/O
Terminal
Any I/O
Terminal
AUXTerminal
1 NORMALLY
CLOSED
CONTACT WITH
5600Ω
END OF LINE
RESISTOR
Any I/O
Terminal
•
•
AUXTerminal
1 NORMALLY OPEN
CONTACT WITH
5600 Ω
END OF LINE RESISTOR
Any I/O
Terminal
AUXTerminal
1 NORMALLY OPEN
CONTACT AND
1 NORMALLY CLOSED
CONTACT WITH
5600Ω END OF LINE
RESISTOR
Figures are based on maximum wiring resistance of 100
Section [009] selects hardwired zone definition
Section [013] Opt [1, 2] selects I/O function as Zone (Input) or
PGM (Output)
•
Section [206] Opt [1,2] activates zones 33 & 34
•
Sections [133], [134] Opt [14] selects Normally Closed
•
Sections [133], [134] Opt [15] selects SEOL resistors
•
Sections [133], [134] Opt [16] selects DEOL resistors
Zone Status - Loop Resistance/Loop Status
•
Fault - 0 (shorted wire/loop)
•
Secure - 5600 (contact closed)
•
Tamper - infinite (broken wire, open)
•
Violated - 11,200 (contact open)
Any I/O
Terminal
2 NORMALLY CLOSED
CONTACTS WITH
NO END OF LINE
RESISTOR
Burglary Zone Wiring Chart
Wire
Gauge
AUXTerminal
AUXTerminal
2 NORMALLY OPEN
CONTACTS AND
2 NORMALLY CLOSED
CONTACTS WITH
5600Ω END OF LINE
RESISTOR
Double End-of-Line (DEOL) Resistor Wiring
Any I/O
Terminal
ALARM
CONTACT
AUXTerminal
Any I/O
AUXTerminal Terminal
ALARM
DEOL CIRCUIT
CONTACT
1 NORMALLY
CLOSED CONTACT
WITH 5600Ω
END OF LINE RESISTORS
TAMPER
CONTACT
DEOL CIRCUITS
2 NORMALLY
CLOSED CONTACTS
WITH 5600Ω END
OF LINE & TAMPER
RESISTOR
2.2.2 PGM/Aux Power Wiring
PGMs switch to ground when activated by the alarm panel.
Connect the plus side of the device to be activated to the AUX+ terminal.
Connect the minus side of the device to the PGM. Each PGM can provide
50mA output.
I/O
I/O
NOTE: The alarm panel can provide a maximum of 100mA of AUX current for PGMs, relays, LED’s etc. Min/Max operating voltages for PGMs,
relays and modules is 12VDC - 12.6VDC.
LED output with
current limiting
resistor and optional
relay driver output
NOTE: Battery Voltage (6.0-8.4VDC) is boosted internally to supply
12VDC on the AUX+ output by setting Section [014] Opt. [4] to ON. This
option must be enabled for PGMs used in UL/ULC Residential Burglary
installations. This output can NOT be used for UL/ULC Fire installations.
2.2.3. Telephone Line Wiring
Wire the telephone connection terminals (TIP, Ring, T-1, R-1) to an RJ31X connector as indicated. Use 24 AWG wire minimum for wiring.
For connection of multiple devices to the telephone line, wire in the
sequence indicated.
Communication format is programmed in section [350].
Telephone Call Directions are programmed in section [351]-[376].
T-1
R-1
TIP
RING
BRN
GRA
GRN
RED
RJ-31X
Note: For UL listed installations, the installer must verify the communication format with the supervising station at the time of installation.
6
WWW.DIYALARMFORUM.COM
2 Installation
2.2.4 Battery
2.2.5. AC Wiring
For systems without an alternate communicator module, a 1500 mAh NiMh battery pack is included to meet battery standby requirements. For systems with an alternate communicator module, a 3600 mAh Ni-MH battery
pack is included.
Note: UL/ULC Residential Burglary installations require 4 Hr. battery
standby time plus 4 minutes alarm annunciation.
Note: UL/ULC Residential Fire installations require 24 Hr. battery
standby plus 5 minutes alarm annunciation.
Note: Battery life is 3-5 years under typical operating conditions. Battery
capacity deteriorates with age and number of charge/discharge cycles.
Replace battery every 3-5 years.
AC Transformer Requirements:
Primary:120VAC, 50/60Hz., 0.33A (NA), 240VAC, 50/
60Hz., 0.165A (EU)
Secondary: 16.5VAC/20VA
The following transformers shall be used:
UL/ULC Listed Installations - PTD1620U-CC
Note: Do not connect the transformer to a receptacle controlled by a switch. For UL/ULC Installations use a Class 2, power limited, plugin transformer.
2.3 Wireless Device Setup
This section describes how to configure wireless devices to work with the alarm panel.
2.3.1 Receiver Placement Test
Receiver Placement test ensures the SCW9055/57 is located in an area with low noise and interference and can successfully receive signals from wireless devices.
To perform a receiver placement test:
1. Enter Wireless Device Placement Test mode:
[ ✱ ][8][XXXX][904] - for wireless zones
[ ✱ ][8][XXXX][905] - for wireless keypad/ IT-410
[ ✱ ][8][XXXX][906] - for wireless sirens
[ ✱ ][8][XXXX][907] - for wireless repeaters
2. The Yellow LED on the SCW9055/57 lights indicating unacceptable RF traffic level or noise floor level. Once Wireless Device
Placement Test mode is entered, Receiver Placement Test is continuously active until placement mode is exited or Installer programming times out.
2.3.2 Wireless Device Enrollment
Enrollment consists of programming the device's Electronic Serial Number (ESN) into the panel so that it can be identified when an
event is communicated. Two-way devices must also initiate communication with the control panel to complete the enrollment process.
The control panel assigns a unique system ID, device ID and encryption key to the device. This information is stored in the device’s
memory.
Note: The ESN is a 6-digit alphanumeric number located on a removable sticker on the wireless device.
Methods of Enrollment
Two methods of enrollment are available:
•
Quick Enroll – Used to enroll new devices on the system (see below for procedure). The Quick Enroll procedure performs one-way
and two-way enrolment communications in the background. The enrollment procedures for both types of devices are identical.
•
Manual or DLS Enroll – See Installer Programming or DLS Programming (Section [804]). Manual or DLS enrollment of wireless keys requires the device to be physically triggered to complete the enrollment.
Enroll wireless devices in the following sequence: Keypad, Sirens, Sensors, Pendants, Wireless Keys, Repeaters.
Refer to the associated installation sheets for additional details on how to activate specific wireless devices.
Enrolling The Secondary Keypad
During initial power up of the alarm panel, a 2-minute window is established for enrolling the secondary keypad. If the AC Power and
Ready LEDs flash for the duration of this window, the keypad must be powered up and enrolled within this period. If not (i.e., The AC
Power and Ready LEDs stop flashing), power down the panel then power up again to re-open the 2-minute enrollment window.
To enroll a keypad:
1. Power up alarm system.
• Connect alarm system to AC Power. The Ready and AC LEDs flash for 2 minutes.
2. Power up keypad.
• Connect keypad to AC power or install new batteries. After a few seconds the keypad may beep rapidly and the LCD displays
the following: “Hold [1] and [ ✱ ] to Enroll Keypad.”
• Press the [ ✱ ] and [1] keys simultaneously to enroll the keypad. “WFKP Enrollment Successful” is displayed.
i
If the “Failed to Enroll” message is displayed perform the following:
•
Retry the enrollment.
•
Reposition the keypad closer to the control panel.
•
Verify that the READY and POWER LED indicators are flashing on the panel. If not, disconnect the panel from AC and DC
power sources then reconnect.
•
Check for RF interference. See “2.3.2 Wireless Device Enrollment” on page 7 for more information.
WWW.DIYALARMFORUM.COM
7
SCW9055/57 Wireless Alarm System
Quick Enrolling Keypads, Sirens, Wireless Keys & Repeaters
1. Enter [ ✱ ][8][5555][898]. The following is displayed: “Wireless Enrollment Mode.”
2. Activate the device as indicated below or in the device’s installation sheet.
• Additional keypad: Press the [ ✱ ] and [1] keys simultaneously.
• Siren: Power up the device, press the Tamper button or the test button to enroll.
• Wireless key: Press any key to activate. To re-enroll on another system, press and hold
and
simultaneously for 3 seconds.
• For IT-410 - Press Enrollment button (Note: A keypad must be enrolled before the IT-410 can be enrolled).
• Ensure that dip switch 3 on the repeater is in the off position before quick enrolling a repeater on the SCW9055/57. Press the
tamper button to enroll.
3. The Electronic Serial Number (ESN) is displayed on the keypad. Press [ ✱ ] to confirm the ESN. If the ESN is incorrect press [#]
then repeat this step.
4. After successful confirmation of the ESN, the system prompts for the slot number.
• The next available slot for the device type is displayed. Press [ ✱ ] to accept or enter the slot number.
(keypads = 01, Sirens = 01-02, wireless keys = 01-16, wireless repeaters = 01-04).
• To re-enroll a wireless key press
simultaneously for approximately 3 seconds.
Quick Enrolling Sensors & Pendants
1. Enter [ ✱ ][8][898]. The LCD displays the following: “Wireless Enrollment Mode.”
2. Place the wireless device in the desired location.
3. Activate the device as described in the associated installation sheet. The electronic serial number (ESN) is displayed.
4. Press [✱] to confirm the serial number. If the serial number is incorrect, press [#] and repeat this step. After successful confirmation
of the serial number, the system prompts for the zone number. The next available zone is displayed.
5. Enter a zone number (01-32) then press [ ✱ ] to accept. The next available zone is preloaded.
NOTE: Only one device may be enrolled in each zone. If a zone already has a device enrolled, press [*] to overwrite the zone or
[#] to enter another zone number.
6. After successful entry of the zone number, the system prompts for the zone type. (The recommended zone type is displayed). Press
[ ✱ ] to accept the zone type or enter:
7.
8.
Device Type
Zone Definition
2 Door/Window Contact
3 PIR or Glassbreak
4 Smoke Detector
5 Pendant
6 & 9 Wireless Key
A Wireless Repeater
[01] Delay 1
[05] Interior, Stay-Away
[88] Standard 24-Hour Fire (Wireless)
[16] 24-Hour Panic
N/A
N/A
After successful entry of a valid zone type, the alarm panel automatically enters individual placement test mode for the zone that
was enrolled. “Activate Device for Test, Exit # ” is displayed on the screen. The device may now be placement tested. See below
for details.
Press the [#] key to return to the quick enroll screen. Repeat the above procedure for the next zone.
Quick Enrolling Proximity Tags
If this function is available on the keypad, the [ ✱ ][5] menu provides the option to assign a proximity tag to an access code once the
access code has been entered. Swipe the tag to enroll it during user access code assignment.
i
To unenroll a proximity tag, the user code must be deleted.
Manual Enrollment
To manually enroll a 2-way wireless device:
1. Enter [*][8][5555][804].
2. Select the programming section corresponding to the device type:
•
•
•
•
•
•
3.
4.
8
Wireless sensors and pendants
Wireless Key
Wireless Keypad
IT-410
Wireless Siren
Wireless Repeater
[804][001]-[032]
[804][101]-[116]
[804][201]
[804][202]
[804][301]-[302]
[804][401]-[404]
Enter the device serial number.
Activate the device as indicated in the device’s installation sheet. This can be done while in Installer Programming or after exiting.
The device is now enrolled.
WWW.DIYALARMFORUM.COM
2 Installation
2.3.3 Wireless Device Placement Test
Perform wireless device placement testing on keypads, sirens, sensors and repeaters only.
•
During placement test, the sensitivity of the wireless receiver is reduced significantly. This is done to ensure that, if consistent
good placement test results are generated with reduced sensitivity, the product should have more than adequate range when placement test exits and the sensitivity level returns to normal. During placement test, try to avoid tripping multiple devices at the same
time as this may cause collisions. A collision may cause a bad placement test result, despite having adequate coverage between the
receiver and the transmitter.
•
During placement test, the wireless receiver will require 3 out of 4 wireless packets to be received before a good placement test
result is obtained. Outside of the placement test mode, one wireless packet received is enough to generate an alarm or trouble condition.
•
This test is NOT required for wireless keys or panic pendants. Verify that wireless keys operate within the desired operating area
by arming/disarming the system.
•
Test each wireless device a minimum of 5 times to ensure the location is good. Ideally all 5 attempts should provide a good placement test result.
•
If a device tests bad, reposition it and test again. A slight change in placement, or the orientation of the transmitter, can cause significant differences in the signal strength and range of a wireless device.
•
Avoid mounting wireless transmitters on metal door or window frames whenever possible.
Note: The indoor siren sounds during placement test, even if it is disabled in section [804][311]-[314] option 1. The outdoor siren
sounds during placement test only if section [804][311]-[314] option 1 is enabled.
Wireless Zone Placement Test
1. To placement test a zone, press [ ✱ ][8][XXXX][904]. [XXXX] represents the installer code. The LCD displays the following:
“Select Device for Test < >.”
2. To perform a placement test on an individual zone, type the 2-digit zone number (01 to 32).
To perform a global placement test on a zone, type [00]. In this mode, all wireless zones, keypads, sirens and repeaters are placement tested at the same time. To perform another Wireless Zone Placement test, exit the global placement test by pressing [#] and
begin a new test.
3. Place the wireless device(s) in the intended mounting location(s).
4. Activate the device(s) as described in the associated installation sheet. The device name and zone number are displayed on the
LCD.
• If the alarm system receives a STRONG signal, the bell sounds once and “Location is Good” is displayed on the LCD.
• If the alarm system receives a WEAK signal, the bell sounds 3 times and “Location is Bad” is displayed on the LCD.
• If the alarm system indicates no response, reposition the wireless device(s) and repeat the test.
• For individual placement tests, repeat step 2-3 for each device.
5. When placement testing is complete, press [#] to exit Installer Programming.
i
Two-way wireless keys must be activated by pressing any key before they become functional.
To placement test a wireless keypad, press number keys 0-9.
To placement test a wireless siren or repeater, press the Test button or tamper the device.
2.3.4 Individual Wireless Device Placement Test
Individual placement testing can be performed on wireless devices. Use the scroll keys or enter a 2-digit entry to select a specific
device.
1.
2.
3.
4.
5.
6.
To individually test wireless devices, press:
[ ✱ ][8][XXXX][905] - for wireless keypads/IT-410
[ ✱ ][8][XXXX][906] - for wireless sirens
[ ✱ ][8][XXXX][907] - for wireless repeaters
NOTE: [XXXX] represents the installer code (default 5555).
Select the wireless device you want to placement test by typing the number of the device. In section [905], type 01 for WT5500
keypad or 02 for IT-410. In section [906], type 01-02 for siren 1 or 2. In section [907] type 01-04 for wireless repeater 1-4. Alternatively, scroll to the desired device and press [ ✱ ] to begin the individual placement test.
Place the wireless device in the intended mounting location.
Activate the device as described in the associated installation sheet.
• If the alarm system receives a STRONG signal the bell sounds once and “Location is Good” is displayed on the LCD.
• If the alarm system receives a WEAK signal the bell sounds 3 times and “Location is Bad” is displayed on the LCD.
• If the alarm system indicates no response, reposition the wireless device and repeat the test.
Repeat Step 2-3 for each device. Once the placement test is complete for the device, press [#] once to select the next similar device.
When placement testing is complete, press [#][#][#] to exit Installer Programming.
2.4 Alternate Communicator Module Setup/Initialization
After system installation and programming, ensure that the following sections are programmed:
• Central Station Phone Number, (Template Programming - Entry 5) (if applicable, in sections [301]-[303] & [305])
• Account code, section [310], (Template Programming - Entry 6)
• Communications Format, Section [350]- set to [03] Contact ID or [04] SIA FSK
• alternate communicator Module Enable section [382] Option [5] - set to “alternate communicator module enabled”
WWW.DIYALARMFORUM.COM
9
SCW9055/57 Wireless Alarm System
3 Operation
3.1 Operating Modes
3.1.1 – Away Arming
Away Arming arms the entire system including the perimeter and interior devices. The Ready light must be on to arm the system. If the Ready
light is off, ensure all protected doors and windows are secure or bypassed. To arm in Away mode, press and hold the Away function key for 2
seconds or enter a valid user code and leave the premises through a door programmed as Delay. The Armed light turns on when a function key
is pressed or an access code is entered. If the Audible Exit Delay option is enabled, the keypad beeps once every second during the exit delay
(and three times a second during the last 10 seconds) to alert the user to leave. The Ready light turns off when the Exit Delay ends.
NOTE: In Away Arming mode, manually bypassed zones are logged and communicated to the central station.
3.1.2 – Stay Arming
NOTE: Zones must be programmed with zone definitions (05 Interior Stay/Away, 06 Delay Stay/Away, or 32 Instant Stay/Away) for
this function to work.
Stay Arming is intended to arm the perimeter of the premises while permitting movement within. The Ready light must be on to arm the
system. If the Ready light is off, ensure all protected doors and windows are secure or bypassed. To Stay arm the system, press and hold
the Stay function key for 2 seconds or enter a valid user code and stay within the premises (do NOT violate a door programmed as
Delay). The Armed light turns on once a function key is pressed or an access code is entered. If the Stay function button is used, the
keypad will not beep during the exit delay and the user can still exit the building without the system reverting to Away mode. When a
user code is used, the keypad beeps if the Audible Exit Delay option is enabled. The Ready light turns off when the exit delay ends.
NOTE: In Stay Arming mode, all auto-bypassed stay/away and night zones are logged and communicated to the central station.
3.1.3 – Night Arming
Night arming is intended to arm the perimeter and restrict movement to designated areas in the interior (e.g., hallways from bedrooms to bathrooms). If night zones are programmed, entering [ ✱ ][1] while the system is armed in stay mode will activate all interior zones except those programmed as night zones. The panel can also be armed in Night mode by pressing the Night Arm function key for 2 seconds while the system is
disarmed. The Ready light must be on (disarmed) or the system must be armed in Stay mode to Night arm the system. In Night mode only night
zones (Zone definition 37) are bypassed. When activated, no acknowledgement beeps are sounded, the exit delay is silent and the panel logs
“Armed in Night Mode.” If no night zone types are programmed, the system arms in Away mode and the panel logs “Armed in Away Mode.”
NOTE: In Stay Arming mode, all auto-bypassed night zones are logged and communicated to the central station.
3.1.4 – Disarming
The user must enter through a door programmed as Delay. Upon entering, the keypad emits a steady entry delay tone (and a pulsing
tone during the last 10 seconds of entry delay) to alert the user to disarm the system. To disarm the system, enter a valid user code, present a proximity tag or use a wireless key. If an alarm occurred while the panel was armed, the keypad displays “Alarm in Memory” and
the zone(s) that went into alarm during the armed period. Press the [#] key to return the keypad to the Ready state.
3.2 Language Selection
The keypad can be programmed to display messages and labels in different languages. Languages can be selected before the keypad is
enrolled on the system. Perform the following when in “Ready to Arm” mode or at the Installer Programming menu:
(1) Press and hold both scroll keys [< >] simultaneously until language options are displayed.
(2) Scroll to the desired language using the scroll keys [< >].
(3) Press [ ✱ ] to select the desired language.
3.3 [ ✱ ] Commands
The following is a list of the [ ✱ ] commands available and a description of each:
[ ✱ ][1]
Bypass (disarmed state)/Reactivate Stay/Away Zones (armed state)
Display Trouble Conditions
[ ✱ ][2]
Display Alarm Memory
[ ✱ ][3]
Door Chime Enable/Disable
[ ✱ ][4]
[ ✱ ][5][Master/Supervisory Code]
User Code Programming and Proximity Tag Enrollment
User Functions
[ ✱ ][6][Master/Supervisory Code]
Command Outputs 1 and 2
[ ✱ ][7][1/2]
[ ✱ ][8][Installer Code]
Installer Programming
No-Entry Arming
[ ✱ ][9][User Code]
Quick Arm (disarmed state)/Quick Exit (armed state)
[ ✱ ][0]
[ ✱ ][1] – Bypass/Re-activate Stay/Away and Night Zones
Press [ ✱ ][1] to enter the bypass mode. If the Code Required for Bypass option is enabled, enter a valid user code. The keypad will display ‘Scroll to Bypass Zones.’ The keypad will display the programmed zone labels for the zones and include the letter ‘O’ in the bottom, right corner if the zone is violated or the letter ‘B’ if the zone is bypassed. Scroll to the appropriate zone and press the [ ✱ ] key to
change the bypass status (or enter the 2-digit zone number). Once the correct zones are bypassed, press [#] to exit.
10
WWW.DIYALARMFORUM.COM
3 Operation
Additional Bypass Commands:
Bypass Recall:
Clear Bypass:
Save Bypass:
Recall Save:
Press [99].
Press [00].
Press [95].
Press [91].
The keypad will recall the last group of zones that were bypassed.
The keypad will clear the bypass on all zones.
The keypad will save which zones are manually bypassed.
The keypad will recall the bypassed zones that were saved.
Re-activate Stay/Away and Night Zones:
Press [ ✱ ][1] when the system is armed in the Stay mode to change the armed status to Away mode or Night mode. The system will add
the Stay/Away zones back into the system after the exit delay time expires.
If any zones are programmed as Night Zones (zone definition 37) pressing [ ✱ ][1] will activate the Night mode instead of Away mode.
Only Night Zones will be bypassed.
[ ✱ ][2] – Trouble Display
Refer to Section 6: Testing & Troubleshooting, for troubleshooting assistance and a detailed description of all trouble conditions.
[ ✱ ][3] – Alarm Memory Display
Pressing the scroll < > keys will display an “Alarms in Memory” message if an alarm occurred during the last armed period. Pressing
[✱][3] will display the message “Scroll to view Alarms.” Scrolling will display the zones that went into alarm. To clear the memory, arm
then disarm the system.
[ ✱ ][4] – Door Chime Enable/Disable
Press [ ✱ ][4]. The keypad emits 3 rapid beeps to indicate that the door chime feature is enabled or a steady 2-second tone to indicate it is
disabled. The same function can be performed by pressing and holding the Chime function key for 2 seconds.
[ ✱ ][5] – Program User Codes
The following table identifies available user codes:
Code
Type
[01] – [16]
General User Codes
[40]
Master Code
Function
Determined by attributes programmed below
All attributes described below
Programming User Codes
Press [ ✱ ][5] followed by the master code. The keypad displays the first user (user 01) and includes the letter “P” if the user code is programmed. Scroll to the appropriate user number and press the [ ✱ ] key to program the user (or enter the 2-digit user number). Enter a
new 4 or 6-digit user code or press [ ✱ ] to delete the user code. After the user code is programmed or deleted, scroll to another user number or press [#] to exit.
NOTE: Proximity tags can be assigned to a programmed user code on WT5500P keypads. After assigning a user code, swipe the tag to
assign it to the user. A T is displayed in the lower right hand corner of the user code indicating that a tag is associated with it.
To delete a proximity tag, the user code must be deleted. Refer to the Proximity Tag Installation Sheet for details. The proximity tag can be used in place of the access code for any of the featured referred to in the Operation section of this manual.
Programming User Attributes
Press [ ✱ ][5] followed by the master code or supervisor code. Press [9] followed by the 2-digit user number to view user attributes.
To change user attributes, press the number corresponding to the attribute or scroll to the desired attribute and press [ ✱ ]. When the correct attributes are assigned to the user, press [#] to exit. To change the attributes for another user, press [9] followed by the 2-digit user
number. When finished, press [#] to exit.
NOTE:
• These attributes affect the operation of wireless keys.
• Wireless key numbers (01-16) correspond with user access codes (01-16).
• Duress codes are not valid when entering [ ✱ ][5], [ ✱ ][6] or [ ✱ ][8] sections.
• Duplicate codes and codes that are ± 1 of an existing code can not be programmed.
[1]
Supervisor’s Code: This code is used for validation when entering the [ ✱ ][5] User Code Programming section and [ ✱ ][6]
User Functions section. Note, the supervisor’s code can only validate programming for codes with equal or lesser attributes.
The supervisor’s code also allows the user to create bypass groups if an access code is required to enter [ ✱ ][1] Bypassing.
[2]
Duress Code: Duress codes are standard user codes that transmit the Duress Alarm Reporting Code whenever the code is
entered to perform any function on the system.
[3]
Bypass Zones: The user can manually bypass zones if bypassing requires an access code.
[4]
Phone Access: This attribute is used to specify which users can access the system remotely.
Note: After 5 invalid access codes, remote access is locked out. The invalid access codes timer is cleared every 60 minutes.
Valid access codes do not reset the invalid access code count.
[5-6]
[7]
Future Use
Bell Squawk On Arming/Disarming: The panel squawks the bell when the user arms using the Away function key and a
user code, or if the away function key is pressed on an identified wireless key.
WWW.DIYALARMFORUM.COM
11
SCW9055/57 Wireless Alarm System
[8]
One-time Use Code: The one-time-use code allows unlimited arming but only permits a single disarming once a day. The
Disarm function is restored at midnight.
[ ✱ ][6] – User Functions
To access the User Functions section, press [ ✱ ][6] followed by the master or supervisor code. Select one of the functions described
below by pressing the corresponding number or scrolling to the desired option then pressing [ ✱ ].
[1]
Program Time and Date: Enter the time and date using the following format [HH:MM] [MM/DD/YY]. Program the time
using military standard (e.g., 8:00 pm = 20:00 hours).
[2]-[3] Future Use
[4]
System Test: The system activates the siren output on medium volume for 2 seconds followed by full volume alarm for 2
seconds. All display lights and LCD pixels turn on.
[5]
System Serv/DLS: Installer Programming, either by DLS or via the keypad ([ ✱ ][8]), is enabled for 6 hours.
[6]
User Initiated DLS: The panel attempts to call the DLS computer.
[7]
Future Use
[8]
User Walk Test Mode: This mode tests the operation of each detector in the system. Press [ ✱ ][6][Master Code][8] to initiate
Walk Test. While in Walk Test, the Ready, Armed, and Trouble LED's on the keypad flash to indicate that the test is active.
When a zone is violated during the test, a 2-second tone sounds on all system keypads to indicate that the zone is working
correctly. Re-entering [ ✱ ][6][Master Code][8] exits Walk Test. The system automatically ends the test after 15 minutes without
zone activity. An audible warning (5 beeps every 10 seconds) is sounded, beginning 5 minutes before the test ends.
NOTE: Do not activate [F]ire, [A]uxiliary and [P]anic keys, or Fire and CO zones during a walk test. If an [F], [A], or [P] key is
pressed during a walk test, or if a fire or CO alarm is detected, walk test ends automatically and the reporting codes for the
alarm are sent immediately to the monitoring station.
[9]
Late to Open Control: Notifies a user if their alarm system is not disarmed by a programmed time of day (see Late to Open
Time of Day). If the system is not disarmed at the programmed time, an alert is sent to the monitoring station. The keypad
displays “Late to Open is Enabled” and sounds a beep if [9] is pressed within the User Functions menu when this feature is
off. The LCD keypad displays “Late to Open is Disabled” and sounds an error tone if [9] is pressed within the User
Functions menu when this feature is on.
[0]
Late to Open Time of Day: Sets the time for Late to Open Control programmed for attribute [9] operation. Valid entries are
00:00 - 23:59. Entering 99:99 disables the late to open feature for that day. After [0] is pressed in the [ ✱ ][6] menu, acknowledge
beeps are sounded and the message “Press (✱) for < > Sunday” is displayed on the keypad. Pressing [>] scrolls through each day
of the week from Sunday to Saturday. While in the Late to Open menu, entering keys 1-7 also selects the day.
Additional Keypad Functions
The following additional keypad functions are available:
Event Buffer:
Brightness Control:
Contrast Control:
Buzzer Control:
SMS Phone Number Programming:
View the 500-event panel buffer
Adjust the display backlighting level for optimal viewing
Adjust the display contrast level for optimal viewing
Adjust the keypad buzzer tone for optimal sound
Program up to 8 phone numbers for the panel to accept incoming SMS commands
[ ✱ ][7][1 or 2] – Command Outputs (1&2)
Press [ ✱ ][7] then [1] or [2]. If the Command Output Code Required option is enabled, enter a valid user code. The panel activates a
command output assigned to any PGM.
[ ✱ ][8] – Installer Programming
Press [ ✱ ][8][Installer Code] to enter Installer Programming. Installer programming allows the installer to program all system functions.
Refer to section 5: Installer Programming, for details.
[ ✱ ][9][User Code] – No-Entry Arming
Press [✱][9] followed by a valid user code. The system arms in the Stay mode after the exit delay expires and removes the entry delay. All
zones programmed as Delay function in the same way as Instant zones. The system flashes the Armed light to indicate that it is armed
with no entry delay.
[ ✱ ][0] – Quick Arm/Quick Exit
Quick Arm: When disarmed, press [ ✱ ][0] to arm the system. Quick Arm is equivalent to entering your user code.
Quick Exit: When armed, press [ ✱ ][0] to activate Quick Exit. Quick Exit allows you to exit the premises without disarming the system.The system allows a single zone programmed as Delay to be violated and restored once during the following 2 minute time period
without changing the status of the system.
12
WWW.DIYALARMFORUM.COM
3 Operation
3.4 Function Keys
The keypad has 5 programmable one-touch function keys located in a column down the right-side of the keypad. These keys can also be
activated by pressing and holding number [1] through [5] respectively for 2 seconds. The default for these keys are as follows:
[1] Stay Arm
[2] Away Arm
[3] Chime Enable/Disable
[4] Bypass
[5] Quick Exit
3.5 System Removal Prevention
The SCW9055/57 includes a feature to prevent intruders from disabling the system by removing it from the wall.
This feature operates as follows:
1. When an entry delay is started, the panel notifies the alternate communicator.
2. The communicator establishes contact with the network as soon as it receives the above notification.
3. If a system tamper is detected, the panel notifies the communicator, sending a burglary event to the central station.
WWW.DIYALARMFORUM.COM
13
SCW9055/57 Wireless Alarm System
4 Programming
The SCW9055/57 can be programmed using the following methods:
Programming Method
Description
Procedure
Press [899] at the “Enter Section” screen.
See Template Programming below for details.
Template Programming
Allows the minimum required data to be programmed. It also allows for the setup of DLS
downloading software.
DLS Programming
DLS Programming can be set up from Template ProAllows programming to be downloaded using
gramming (See Steps 3, 4 and 5) or from Installer ProDLS-IV™ software.
gramming (See programming sections [401]-[404]).
• DLS programming can be performed locally
with a PC-Link cable and a PC with DLS-IV
software installed.
• DLS programming can be performed remotely
via telephone line, Cellular network or the
Internet.
Installer Programming
Allows direct access to all programming sections. Press [*][8][Installer Code] while the system is disTemplate programming is accessed from here.
armed.
Refer to Installer Programming in section 4.3 for
details.
4.1 Template Programming
Template Programming allows the installer to quickly program the minimum functions required for basic operation. The installer is
prompted to enter a 4-digit code that selects predefined zone definitions, reporting code formats, and troubles/restores (see the tables for
digits 1 - 4 below).
Perform the following after completing the hardware installation. Ensure you have the information listed below available for programming. Record this information in “5.3 Programming Worksheets” on page 20 for future reference:
•
Monitoring Station Telephone Number - Provided by your alarm monitoring service.
•
Monitoring Station Account Code - Provided by your alarm monitoring service.
•
Downloading Access Code.
•
Entry Delay - Installer defined.
•
Exit Delay - Installer defined.
•
Installer Code - Programmable, unique 4-digit code. The default value is [5555].
To perform template programming:
1. At the “Ready to Arm” screen, enter [*][8][5555][899].
2. At the “Enter Data” screen, enter [0001] to accept the existing default programming. See the tables
below for details of digits 1-4.
NOTE: Once this section has been entered, the Installer cannot exit until all sections are completed.
Enter new data and/or press # key to accept the displayed data and proceed to the next section.
Changing a single digit, then pressing the # key advances to the next section but does not save
the changed data. Enter all 4 digits or scroll to the end of template programming and exit to
save data.
3. After entering [0001], the first telephone entry is displayed. Enter the monitoring station telephone
number after the “D.” Press [#] to complete the entry.
4. After programming the first telephone number, enter a system account code.
• The system account code can be any 6-digit combination of numbers (0-9) and letters (A-F). If the
system account code is 4-digits, the last two digits must be “FF.”
• To enter letters A through F, press [*] then the numbers 1 through 6 for the letter A through F
respectively. Press [*] again to revert back to decimal entry. E.g., to enter “1234FF” press
[1234*66].
See section [310] for additional details.
5. After programming the system account code, the downloading access code is displayed. Enter the new
downloading access code or press [#] to proceed to the next step. See section [403] for additional
details.
6. The entry delay is the amount of time given to disarm the alarm system, after entering the premises
through a delay type zone, before an alarm is sounded. Press [>][>][>] to accept the default time of 30
seconds (030) or enter an entry delay between 001 and 255. E.g., Press 020 for a delay of 20 seconds.
See section [005] for additional details.
7. The exit delay is the amount of time given to exit the premises after pressing the Arm key before the
alarm system is armed. Press [>][>][>] to accept the default time of 120 seconds or enter an entry
delay between 001 and 255. E.g., press 030 for a delay of 30 seconds. See section [005] for additional
details.
14
WWW.DIYALARMFORUM.COM
4 Programming
8.
9.
•
After programming the exit delay, enter a 4 or 6-digit installer code depending on the value in section
[701] option 5. See “[006] Installer Code” on page 20 for installer code details.
Press [#] to exit Template Programming.
Digit 1 selects 1 of the following 6 options for Zone definitions for the first 8 zones. A “0” in the digit 1 location indicates that the
default settings for the first 8 zones are in place unless overridden. See Section [001]-[002] on page 20 for defaults.
Option Zn1
Zn2
Zn3
Zn4
Zn5
Zn6
1
1
3
3
3
4
4
2
1
3
3
5
5
5
3
1
3
3
5
5
5
4
1
1
3
3
3
3
5
1
3
3
6
5
5
6
1
3
3
6
5
5
Refer to “[001]-[002] Zone Definitions” on page 40 for details
•
•
Zn7
4
5
5
3
5
5
Zone Definitions (Options 1- 6)
1 Delay 1
2 Delay 2
3 Instant
4 Interior
5 Interior Stay/Away
6 Delayed Stay/Away
87 Delayed 24Hr. Fire (Wireless)
88 Standard 24 Hr. Fire (Wireless)
Zn8
4
88
87
3
5
88
Digit 2 selects 1 of the following 6 options for Reporting Codes
Opt# Phone Line 1
Programming Section Phone Line 2
Programming Section
1
Disabled
[380] Opt 1 OFF
2
SIA automatic reporting codes enabled [350] 1st Phone # [04] SIA automatic reporting codes [350] 2nd Phone # [04]
[380] Opt 1 ON
enabled
[381] Opt 3 OFF
3
Contact ID reporting codes enabled
4
SIA automatic reporting codes enabled [350] 1st Phone #[04] Residential dial
[380] Opt 1 ON
enabled
[381] Opt 3 OFF
[350] 2nd Phone # [06]
5
Contact ID reporting codes enabled
[350] 1st Phone # [03] Residential dial
[380] Opt 1 ON
enabled
[381] Opt 7 OFF
[350] 2nd Phone # [06]
6
Contact ID reporting codes enabled
[350] 1st Phone # [03] Contact ID reporting codes
enabled
[380] Opt 1 ON
[381] Opt 7 OFF
[350] 2nd Phone # [03]
Disabled
[350] 1st Phone # [03] SIA automatic reporting codes [350] 2nd Phone # [04]
enabled
[381] Opt 3 OFF
[380] Opt 1 ON
[381] Opt 7 OFF
Digit 3 selects 1 of the 8 following options
Common Selected
Openings/
Zone
Option
Group
Troubles
Closings
Restores
1


2



3



4




5


6


7



8

 indicates included, Blank indicates default setting,  indicates disabled
DLS/Installer
Lead In/Out







• Common Group - Sets all Reporting Codes to Automatic
Description
Phone 1
Phone 2
Alarm/restore call directions enabled


[351][1] ON, [2] OFF
Tamper/restore call directions disabled


[359][1] OFF, [2] OFF
Opening/closing call directions disabled


[367][1] OFF, [2] OFF
Maintenance call directions enabled


[375][1] ON, [2] OFF
Test transmission call directions disabled


[376][1] OFF, [2] OFF
Set all reporting codes to automatic
Sections
[320] - [348] FF
WWW.DIYALARMFORUM.COM
15
SCW9055/57 Wireless Alarm System
• Selected Troubles - Enables the following Troubles
Trouble
[345] Alarms
[346] Restore
Battery
FF
FF
AC Failure
00
00
Fire Trouble
FF
FF
Aux PS
FF
FF
TLM
XX
00
General System
00
00
FF = General System Trouble, 00 = Disabled, XX = Not transmitted
• Openings & Closings - Sets Residential Dial Reporting Codes for all openings and closings
Users
CLOSINGS, Residential Dial Reporting Codes
1-8
51
52
53
54
55
56
57
Section
9-16
61
62
63
64
65
66
67
68
[339]
40
99
FF
FF
FF
FF
XX
XX
XX
[341]
17
18
58
[339]
Users
OPENINGS, Residential Dial Reporting Codes
1-8
11
12
13
14
15
16
Section
9-16
21
22
23
24
25
26
27
28
[342]
40
98
FF
XX
XX
XX
XX
XX
XX
[344]
Enable Opening/Closings call directions for phone 2
FF=Communicates in automatic mode, XX=Not used
[342]
[367] Opt 2 ON
• Installer Lead-in/Lead-out and DLS Lead-in/Lead-out
DLS Lead In
Sect [347] Opt 4
DLS Lead Out
Sect [347] Opt 5
Installer Lead Out
Sect [347] Opt 11
Installer Lead In
Sect [347] Opt 12
Disabled for all template options except option 8
Digit 4 indicates/selects one of the three following DLS connections
16
Option
Double Call
Call Back
User Call Up
Sect [401] Opt 1 Sect [401] Opt 3 Sec [401] Opt 4
#Rings
Sect [406] Opt 3
1



000
2



008
3



008
4



008
WWW.DIYALARMFORUM.COM
4 Programming
4.2 DLS Programming
4.2.1 Local Programming with PC-Link
Follow the steps below in the sequence indicated to set up local programming using DLS:
1. Connect AC Wiring before mounting the back plate.
NOTE: In a new installation, the backup battery requires 24 Hrs. charging. AC Power is required for
PC-Link Programming until battery is charged.
2. Remove the front cover from the backplate, taking care not to disconnect the alternate communicator module and battery connectors.
3. Initiate a DLS PC-Link session on the DLS computer.
4. Plug in PC-Link header.
5. Initiate DLS session on the DLS computer.
Figure -1, PC-Link Connection
PC-Link
Connector
NOTE: Connecting the DLS PC to the system automatically initiates the connection.
6. When the session is complete, remove the PC-Link cable from the alarm system.
7. Complete the installation.
4.2.2 Local Firmware Upgrade
1. If the unit is mounted on the wall, remove the front cover from the back plate or remove the entire unit from the wall. Plug in the
DLS header. Power down and power up the unit.
NOTE: The DLS session must be initiated within 10 seconds of power up. Do not attempt to perform
a firmware upgrade if low battery trouble is present.
2. Open the Flash Utility application within DLS, select the latest firmware file from the Web or browse to the saved flash file on
your hard drive. Follow the steps as prompted by the Flash Utility application. A message is displayed when download is complete.
3. Once the firmware update is complete, the panel powers up.
4.2.3 Remote Firmware Upgrade
The panel firmware can be upgraded remotely via communicator. If a firmware upgrade is available or if the installed firmware is
faulty, the latest version is installed. During the update, "FW Updating" is displayed on the on-board LCD. If the firmware update fails,
"System Error" (top line) "Service Req." (bottom line) is displayed.
The Panel performs a firmware update under the following conditions:
•
The Panel is not armed
•
No AC trouble is present
•
No low battery trouble is present
•
No FTC trouble is present
•
Every alarm in memory has been viewed
•
No events are being communicated
4.2.4 Remote Programming (via telephone line)
Refer to Section “[401] First Downloading Options” on page 30 and page 55 for details.
NOTE: AC Power must be present for the alarm system to answer incoming calls from DLS.
4.3 Installer Programming
Enter [*][8][Installer Code].
The system prompts for a 3-digit programming section number (refer to Chapter 5 for programming details).
WWW.DIYALARMFORUM.COM
17
SCW9055/57 Wireless Alarm System
5 Advanced Programming
5.1 How to Program
To help reduce programming time and eliminate errors, fill in the Programming Worksheet with the required programming defaults
before programming the system.
To enter Installer Programming, press [][8][Installer Code]. The LCD keypad displays “Enter Section.” An error tone sounds if an
incorrect installer code is entered. Press [#] to clear any key presses and try again.
i
The default installer code is [5555].
The Armed and Ready lights indicate programming status:
Armed Light ON
Panel waiting for 3-digit section number
Ready Light ON
Panel waiting for data to be entered
Ready Light FLASHING
Panel waiting for HEX data to be entered
i
You cannot enter Installer Programming while the system is armed or in alarm.
5.1.1 Programming Toggle Options
Enter a 3-digit programming section number:
•
The Armed light turns OFF and the Ready light turns ON.
•
The keypad displays which toggle options are ON or OFF according to the table below:
•
•
•
Option ON
Option OFF
# Displayed
Dash [-] Displayed
To toggle an option ON or OFF, press the corresponding number on the keypad. The display changes accordingly.
When all the toggle options are configured correctly, press the [#] key to exit the program section.
The Ready light turns OFF, the Armed light turns ON and the LCD displays “Enter Section.”
5.1.2 Programming Decimal and Hexadecimal (HEX) Data
•
Enter a 3-digit programming section number
•
The Armed light turns OFF and The Ready light turns ON
•
Enter data in the spaces provided
For sections that require multiple 2 or 3 digit numbers, the keypad emits a double-beep after each 2 or 3 digit entry and moves to the
next item in the list. After the last digit in the section is entered, the keypad beeps rapidly 5 times and exits the programming section.
The Ready light turns OFF, the Armed light turns ON and the LCD displays “Enter Section.”
For sections that do not require data for every box (such as phone numbers) press the [#] key to exit the programming section after
entering all the required data. The Ready light turns OFF, the Armed light turns ON and the LCD displays “Enter Section.”
At any time the [#] can be pressed to exit a programming section. All changes (excluding Template Programming) are saved.
Hex Digits
In addition to the standard digits 0-9, HEX digits and special dialer functions can also be programmed.
To enter a HEX digit:
1. Press the [] key to begin HEX programming. The Ready light will FLASH.
2. Press the number corresponding to the HEX digit required (1=A, 2=B, 3=C, 4=D, 5=E, 6=F). The Ready light will continue to
FLASH.
3. Press [] again to return to normal decimal programming. The Ready light will turn ON.
5.1.3 How to Exit Installer Programming
To exit Installer Programming, press the [#] key at the “Enter Section” screen.
5.1.4 Viewing Programming
The keypad immediately displays all programmed information when a section is entered. Use the arrow keys (< >) to scroll through the
available data. Scroll past the end of the data displayed or press the [#] key to exit the section.
18
WWW.DIYALARMFORUM.COM
5 Advanced Programming
5.2 Index to Programming Worksheets and Descriptions
Programming Option
PWS/Desc.
[001]-[002] Zone Definitions.............................................. 20/40
[005] System Times ............................................................ 20/42
[006] Installer's Code .......................................................... 20/42
[007] Master Code .............................................................. 20/42
[008] Maintenance Code..................................................... 20/42
[009] I/O Programming ...................................................... 21/42
[012] Keypad Lockout Options .......................................... 21/43
[013] First System Options ................................................. 21/44
[014] Second System Options............................................. 21/44
[015] Third System Options ............................................... 21/45
[016] Fourth System Options.............................................. 22/45
[018] Sixth System Options................................................ 22/46
[023] Tenth System Options ............................................... 22/46
[024] Eleventh System Options .......................................... 22/47
[030] Zone Loop Response Options ................................... 22/47
[101]-[134] Zone Attributes................................................ 23/47
[167] Alt. Comm. Communications Wait for Ack.............. 23/48
[168] Daylight Saving Time Begin..................................... 23/48
[169] Daylight Saving Time End ........................................ 23/48
[170] PGM Output Timer ................................................... 23/48
[176] Cross Zone/Police Code Timer ................................. 24/49
[190] No Activity Arming Pre-Alert Timer........................ 24/49
[191] No Activity Arming Timer........................................ 24/49
[202]-[206] Zone Assignments ........................................... 24/49
[301] First Telephone Number............................................ 24/49
[302] Second Telephone Number ....................................... 24/49
[303] Third Telephone Number .......................................... 24/49
[304] Call Waiting Cancel String........................................ 24/49
[305] Fourth Telephone Number ........................................ 24/49
[310] System Account Code ............................................... 24/49
[320]-[322] Alarm Rep. Codes ........................................... 25/50
[324]-[326] Alarm/Restore Rep. Codes.............................. 25/50
[328] Misc. Alarm Rep. Codes ........................................... 25/50
[329] Priority Alarm/Restore Rep. Codes........................... 25/50
[330]-[332] Tamper Rep. Codes ......................................... 26/50
[334]-[336] Tamper Restore Rep. Codes ............................ 26/50
[338] Misc. Tamper Rep Codes. ......................................... 26/50
[339] Closing (Arming) Rep. Codes................................... 26/50
[341] Misc. Closing (Arming) Rep. Codes......................... 26/50
[342] Opening (Disarming) Rep. Codes ............................ 26/51
[344] Misc. Opening (Disarming) Rep. Codes. .................. 26/51
[345] Maintenance Alarm Rep. Codes ............................... 27/51
[346] Maintenance Restore Rep. Codes ............................. 27/51
[347] Misc. Maintenance Rep. Codes................................. 27/51
[348] Test Transmission Rep. Codes .................................. 27/52
[350] Communicator Format Options................................. 27/52
[351] Alarm/Rest. Comm. Call Directions ......................... 27/52
[359] Tamper/Rest. Comm. Call Directions ....................... 27/52
[367] Opening/Closing Comm. Call Directions ................. 28/52
[375] System Maint. Comm. Call Directions ..................... 28/52
[376] System Test Trans. Comm. Call Directions .............. 28/52
[377] Communication Variables ......................................... 28/53
[378] Test Transmission Time of Day ................................ 28/53
[380] First Communicator Options..................................... 28/53
[381] Second Communicator Options ................................ 29/54
[382] Third Communicator Options ................................... 29/54
[383] Fourth Communicator Options ................................. 29/55
[389] Alt. Comm. Fault Check Timer................................. 29/55
[401] Downloading Options ............................................... 30/55
[402] DLS Downloading Computer’s Phone Number........ 30/56
[403] DLS Downloading Access Code............................... 30/56
Programming Option (cont.)
PWS/Desc.
[404] Panel ID Code............................................................30/56
[405] Double Call Timer .....................................................30/56
[406] Number of Rings to Answer On ................................30/56
[501]-[502] PGM Output Attributes ...................................30/56
[591]-[592] Inactivity Timers 1&2 Start/End Times...........31/57
[600]-[601] 2-way Audio Control Options .........................31/58
[609] Module Tamper Rep. Codes ......................................31/58
[610] Alternate Com. Receiver Trouble Rep. Codes ..........32/58
[611] Repeater Tamper/AC Loss Rep. Codes .....................32/58
[700] Automatic Clock Adjust ............................................32/58
[701] First International Options.........................................32/58
[702] Second International Options ....................................32/59
[703] Delay Between Dialing Attempts ..............................32/59
[800] Door Chime Options for Zones 1-34.........................33/59
[804] Wireless Programming ..............................................33/59
[001]-[032] Wireless Zone Programming ..................33/59
[081] Wireless Supervisory Window .........................33/60
[082]-[085] Zone Transmitter Supervision ................33/60
[101]-[116] Wireless Key Serial Number ..................34/60
[141]-[156] Wireless Key Function Key Options ......34/60
[181]-[182] Wireless Key Enable/Disable .................34/60
[201] Wireless Keypad Serial Number.......................34/60
[202] IT-410 Serial Number .......................................34/60
[301]-[302] Wireless Siren Serial Number.................34/60
[311]-[312] Wireless Siren Options ...........................35/60
[320] Global Siren Options ........................................35/61
[330] Maximum Outdoor Siren Activation Timer .....35/61
[401]-[404] Wireless Repeater Programming ............35/61
[900] General Wireless Options .................................35/61
[850] Cellular Signal Strength.............................................35/62
[851] Alt. Comm. Module Programming............................35/62
[898] Wireless Device Enrollment ......................................35/62
[899] Template Programming .............................................35/62
[900] Panel Version .............................................................35/62
[904]-[907] Wireless Device Placement Test......................36/62
[908] Wireless Modules ......................................................36/62
[990] Installer Lockout Enable............................................36/62
[991] Installer Lockout Disable...........................................36/62
[992] Alt. Comm/Ethernet Module Label Broadcast ..........36/62
[996] Restore Wireless Device Default Programming........36/62
[998] Restore Panel Default Programming .........................36/62
[999] Restore Factory Default Programming......................36/62
Local Keypad Programming ...............................................36/62
[000] Keypad Function Key Programming .........................36/62
[001]-[034] Label Programming (Zone 1-34) .....................36/64
[065] Fire Alarm Label .......................................................37/64
[066] Fail to Arm Event Message .......................................37/64
[067] Alarm When Armed Event Message .........................37/64
[074] First Keypad Options.................................................38/64
[075] Second Keypad Options ............................................38/65
[076] Third Keypad Options ...............................................38/65
[077] Programmed LCD Message.......................................38/65
[078] Programmed LCD Message Duration .......................38/65
[100] CO Detector Alarm Label ...........................................38/65
[101] System Label ..............................................................38/65
[120]-[121] Command Output Labels...................................39/65
[996] Reset Programmable Labels to Factory Defaults .........39/65
[997] Keypad Version...........................................................39/66
[998] Initiate Global Label Broadcast ...................................39/66
[999] Reset All Keypad Programming To Factory Defaults..39/66
WWW.DIYALARMFORUM.COM
19
SCW9055/57 Wireless Alarm System
5.3 Programming Worksheets
Unless indicated otherwise, default values apply to NA and CP-01.
SIA FAR CP-01 defaults are indicated in gray. e.g., or 030
i
[001]-[002] Zone Definitions
00 Null Zone (Not Used)
01 Delay 1*
02 Delay 2*
03 Instant*
04 Interior*
05 Interior, Stay/Away*
06 Delay, Stay/Away*
07-08 Future Use
09 24 Hour Supervisory (Hardwired)
10 24 Hour Supervisory Buzzer*
11 24 Hour Burglary*
12 Future Use
13 24 Hour Gas*
*For burglary applications only
14 24 Hour Heat*
15 24 Hour Medical*
16 24 Hour Panic*
17 24 Hour Emergency*
18 Future Use
19 24 Hour Water*
20 24 Hour Freeze*
21 Future Use
22 Momentary Keyswitch Arm*
23 Maintained Keyswitch Arm (Hardwired)*
24 Future Use
25 Interior Delay*
26 24-hour Non-Alarm (Local Alarm)
** For residential fire applications only
Section Zone Default
Section Zone Default
01
01
I_____I_____I [001]
09
02
03
I_____I_____I
10
03
03
I_____I_____I
04
03
05
04
06
[001]
Section Zone
00
I_____I_____I [002]
17
00
I_____I_____I
18
11
00
I_____I_____I
I_____I_____I
12
00
I_____I_____I
13
00
04
I_____I_____I
14
07
04
I_____I_____I
08
04
I_____I_____I
27-30 Future Use
31 Day Zone
32 Instant Stay/Away*
33 Future Use
34 Future Use
35 Future Use
36 24 Hr. Non-Latching Tamper
37 Night Zone*
81 24-Hour Carbon Monoxide (Wireless)**
82 Future Use
87 Delayed 24 Hr. Fire (Wireless)**
88 Standard 24 Hr. Fire (Wireless)**
89 Auto-verified 24 Hr. Fire (Wireless)**
Default
Section Zone
Default
00
I_____I_____I [002]
25
00
I_____I_____I
00
I_____I_____I
26
00
I_____I_____I
19
00
I_____I_____I
27
00
I_____I_____I
I_____I_____I
20
00
I_____I_____I
28
00
I_____I_____I
I_____I_____I
21
00
I_____I_____I
29
00
I_____I_____I
00
I_____I_____I
22
00
I_____I_____I
30
00
I_____I_____I
15
00
I_____I_____I
23
00
I_____I_____I
31
00
I_____I_____I
16
00
I_____I_____I
24
00
I_____I_____I
32
00
I_____I_____I
[005] System Timers
Valid entries for Entry Delay are between 030-255. Valid entries for SIA CP-01 Exit Delay is between 045-255.
Sub Sect.
Default
[01]
[09]
i
i
Entry Delay 1
Entry Delay 2
Exit Delay
Bell Time-out (BTO)
030
045
120
004
030
060
I___I___I___I
I___I___I___I
I___I___I___I
I___I___I___I
Enter 3 digits from 001-255 (minutes)
If the Exit Delay is silent (section 14, option 6 or Stay Function Key Arming), the exit delay is twice the programmed
value but will not exceed 255 seconds (090-255 seconds)
For UL installations, the Entry Delay plus the Communications Delay must not exceed 60 seconds.
[006] Installer Code
[007] Master Code
[008] Maintenance Code
Default
Default
Default
555555 I_______I_______I_______I_______I_______I_______I 123456 I_______I_______I_______I_______I_______I_______I
AAAA00
I_______I_______I_______I_______I_______I_______I
i These codes are 4 or 6-digits (programmed in section [701] Opt.[5]. For 4-digit codes, the default is the first 4 digits.
20
WWW.DIYALARMFORUM.COM
5 Advanced Programming
Programmable Output Options
00 Null PGM (Not Used)
01 Residential Burglary and Fire Bell Output
02-04 Future Use
05 System Armed Status
06 Ready To Arm
07 Keypad Buzzer Follower
08 Courtesy Pulse
09 System Trouble Output (with Trouble Options)
10 System Event Output (with Event Options)
11 System Tamper (all sources: zones, keypad)
12 TLM and Alarm
13-16 Future Use
17 Away Armed Status
18 Stay Armed Status
19 Command Output #1 ([*][7][1])
20 Command Output #2 ([*][7][2])
21-40 Future Use
[009] I/O Programming
Default
00
00
I_______I_______I
I_______I_______I
I/O Type (Zone 33, PGM 1)
I/O Type (Zone 34, PGM 2)
Enter Zone Definition or PGM Definition
Enter Zone Definition or PGM Definition
i Program Zone Definition Attributes in sections [133-134], Program PGM Option Attributes in sections [501] - [502].
[012] Keypad Lockout Options
Default
000
000
I_______I_______I______I
I_______I_______I______I
Number of Invalid Codes Before Lockout
Lockout Duration (in minutes)
(Valid entries are 000-255)
(Valid entries are 000-255)
i If Keypad Lockout is active, the panel cannot be disarmed with a keyswitch.
[013] First System Options
Opt
1
2
Def.
ON
 
 
Hardwired Zone 33 Input Enabled
 PGM1 Output Enabled
OFF
Hardwired Zone 34 Input Enabled
 PGM2 Output Enabled
 Future Use
3-5
6
 Audible Exit Fault Enabled
7
 Future Use
8
 Temporal Three Fire Signal Enabled
 
Audible Exit Fault Disabled
 
Standard Pulsed Fire Signal
[014] Second System Options
Opt
Def.
1
2
3
4
5
6

7
8








ON
OFF
Arm/Disarm Squawk Enabled

 Arm/Disarm Squawk Disabled
Future Use
RF Jam Log After 5 Minutes
Aux Boost Enabled
 
 
RF Jam Logs After 20 seconds
Aux Boost Disabled
Future Use
Audible Exit With Urgency
 Silent Exit Delay
Future Use
Fire Bell is Continuous
 
Fire Bell Follows Bell Cut-off
[015] Third System Options
Opt
1
Def.
ON

[F] Key Enabled
2
3
4


5
6
7
8









OFF
[P] Key Audible (Siren/Beeps)

Quick Exit Enabled
Quick Arming Enabled ([][0] and Function Keys)
Code Required for Bypassing
Master Code Not Changeable


TLM Enabled
System Tamper Enabled









[F] Key Disabled
[P] Key Silent
Quick Exit Disabled
Quick Arming Disabled (Function Key Requires Code)
No Code Required
Master Code Changeable
TLM Disabled
System Tamper Disabled
WWW.DIYALARMFORUM.COM
21
SCW9055/57 Wireless Alarm System
[016] Fourth System Options
Opt
1
2
3
4
5
6
7
8
Def.

 


 



ON
OFF
Cross Zoning Enabled
Exit Delay Restart Enabled
Blank Keypad When Not Used
Code Required to Remove Keypad Blanking




Keypad Backlighting Enabled





Police Code Enabled
Exit Delay Restart Disabled
Keypad Always Active
No Code Required
Keypad Backlighting Disabled
Future Use
Bypass Status Displayed While Armed
Daylight Saving Time Enabled
 
 
Bypass Status Not Displayed While Armed
Daylight Saving Time Disabled
[018] Sixth System Options
Opt
1
2
3-4
5
6-8
Def.





ON
OFF
Future Use
Keypad Tampers Enabled
 
Keypad Tampers Disabled
 
Keypad Buzzer Follows Siren Disabled
Future Use
Keypad Buzzer Follows Siren Enabled
Future Use
[023] Tenth System Options
Opt
1
2
3
4
5
6
7
8
Def.
ON
OFF
  Chime On Openings Enabled
  Chime On Closings Enabled
 Test Transmission While Armed Only
 Test Transmission Counter In Hours
 Switching from Away to Stay Disabled
  New Alarms will not Disconnect 2-Way Audio
 Trouble Beeps are Silent
 Keyswitch Arms In Away Only













Chime On Openings Disabled
Chime On Closings Disabled
Test Transmission while Armed/Disarmed
Test Transmission Counter In Days
Away to Stay Toggle Option Permitted
New Alarms Disconnect 2-Way Audio
Trouble Beeps Sound Every 10 seconds
Keyswitch Arms In Stay or Away
[024] Eleventh System Options
Opt
1
2
3
4
5
6-8
Def.
ON




Temperature Display Enabled






OFF
Temperature Displayed in Celsius
Internal Siren Enabled
Inactivity Monitored By All Zones
Enable Realtime Clock

 


 
Temperature Display Disabled
Temperature Displayed In Fahrenheit
Internal Siren Disabled
Inactivity Monitored Only By 24 Hr Non-Alarm Zones
Disable Realtime Clock
Future Use
[030] Zone Loop Response Options
Opt
1
2
22
Def.
ON
OFF
 Zone 33 is Fast Loop Response
 Zone 34 is Fast Loop Response
  Zone 33 is Normal Loop Response
  Zone 34 is Normal Loop Response
WWW.DIYALARMFORUM.COM
5 Advanced Programming
[101]-[134] Zone Attributes
Options 9 and 10 do not apply to SCW9055 versions. Options 14, 15 and 16 apply to hardwired zones only (zones 33 & 34). To program
attributes 9 to 16, press 9 within the zone attribute section. Press 9 again to program attributes 1 to 8.
Zone Attribute Defaults
Attribute:
1
2
3
4
5
6
7
 =ON Audible Steady Chime Bypass Force Swing
Zone Type:
OFF Silent
00 Null Zone
01 Delay 1
02 Delay 2
03 Instant
04 Interior
05 Interior Stay/Away
06 Delay Stay/Away
07-08 Future Use
09 24-hr. Superv. (Hardwired)
10 24-hr. Superv. Buzzer
11 24-hr. Burglary
12 Future Use
13 24-hr. Gas
14 24-hr. Heat
15 24-hr. Medical
16 24-hr. Panic
17 24-hr. Emergency
18 Future Use
19 24-hr. Water
20 24-hr. Freeze
21 Future Use
22 Momentary Keyswitch Arm
23 Maintained Keyswitch Arm
24 Future Use
25 Interior Delay
26 24-hr. Non-Alarm (local alarm)
27-30 Future Use
31 Day Zone
32 Instant Stay/Away
33-34 Future Use
35 Future Use
36 24-hr. Non-Latching Tamper
37 Night Zone
81 24-hr. Carbon Monoxide
(Wireless)
87 Delay 24-hr. Fire (Wireless)
88 Standard 24-hr. Fire
(Wireless)
89 Auto-Verified Fire (Wireless)
Pulsed
No
No

























No
No
No












8
9
10
Tx. Cross Zn 2-way TalkDelay
Audio Listen
No



























































































16
Loops


























15
SEOL DEOL
No





No
14
NC





* For UL installations, do not change attribute 5 (Force Arming) from the default setting. For CP-01 installations: Option 6 (Swinger) is defaulted ON for zone
definitions 09-11, 13-17, 19, 20. Option 7 (Tx Delay) is defaulted ON for zone definitions 01-06, 09-11, 13-17, 19, 20, 25, 32, 36, 37.
[167] Alt. Comm. Communications Wait For Ack
Default 060
I_______I_______I_______I
Valid entries are 001-255 seconds
[168] Daylight Saving Time Begin
[169] Daylight Saving Time End
Default
Default
003
Month
|_______|_______|_______| Valid Entries 001-012
011
Month
|_______|_______|_______| Valid Entries 001-012
002
Week
|_______|_______|_______| Valid Entries 000-005
001
Week
|_______|_______|_______| Valid Entries 000-005
000
Day
|_______|_______|_______| Valid Entries 000-031
000
Day
|_______|_______|_______| Valid Entries 000-031
002
Hour
|_______|_______|_______| Valid Entries 000-023
002
Hour
|_______|_______|_______| Valid Entries 000-023
001
Increment |_______|_______|_______| Valid Entries 001-002
001
Decrement |_______|_______|_______| Valid Entries 001-002
[170] PGM Output Timer
Default 005
I_______I_______I_______I
Valid entries are 001-255 seconds
WWW.DIYALARMFORUM.COM
23
SCW9055/57 Wireless Alarm System
[176] Cross Zone/Police Code Timer
Default 060
I_______I_______I_______I
Valid entries are 001-255 seconds/minutes
Default 001
I_______I_______I_______I
Valid entries are 001-255 minutes, 000 for no pre-alert
Default 000
I_______I_______I_______I
Valid entries are 001-255 minutes, 000 to disable
[190] No Activity Arming Pre-alert Timer
[191] No Activity Arming Timer
[202] - [206] Zone Assignments
[202]
Opt
1
2
3
4
5
6
7
8
Zone 1-8
Def.
















[203]
Zones 9-16
Def.
Zone 1








Zone 2
Zone 3
Zone 4
Zone 5
Zone 6
Zone 7
Zone 8
[204]
Zones 17-24
Def.
Zone 9








Zone 10
Zone 11
Zone 12
Zone 13
Zone 14
Zone 15
Zone 16
[205]
Zones 25-32
Def.
Zone 17
Zone 18
Zone 19
Zone 20
Zone 21
Zone 22
Zone 23
Zone 24








[206] Zones 33-34
Def.
Zone 25
Zone 26
Zone 27
Zone 28
Zone 29
Zone 30
Zone 31
Zone 32








Zone 33
Zone 34
Future Use
Future Use
Future Use
Future Use
Future Use
Future Use
Communications
[301] First Telephone Number (32 Digits)
I__D_I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[302] Second Telephone Number (32 Digits)
I__D_I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[303] Third Telephone Number (32 Digits)
I__D_I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[304] Call Waiting Cancel String (6 Digits) - This feature is activated in Section 382 Opt 4
I_____I_____I_____I_____I_____I_____I
i
Default = DB70EF Program unused digits with Hex F
All six digits must be entered for changes to be saved in Section [304] and Section [310]. Fill unused digit spaces with
“F.”
[305] Fourth Telephone Number (32 Digits)
I__D_I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[310] System Account Code
Enter a 4 or 6-digit account number for the system account code. Only SIA supports 6-digit account codes. If a 4-digit code is used, program the last two digits of the account code with FF.
Default = FFFFFF
I_______I_______I_______I_______I_______I_______I
Reporting Codes
i
24
All Reporting Codes are defaulted “FF” unless indicated otherwise.
WWW.DIYALARMFORUM.COM
5 Advanced Programming
[320]-[322] Alarm Reporting Codes, Zones 01-34
Section
[320]
[321]
[322]
Zone 01
Zone 02
Zone 03
Zone 04
Zone 05
Zone 06
Zone 07
Zone 08
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
Zone 09
Zone 10
Zone 11
Zone 12
Zone 13
Zone 14
Zone 15
Zone 16
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
Zone 17
Zone 18
Zone 19
Zone 20
Zone 21
Zone 22
Zone 23
Zone 24
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
Zone 25
Zone 26
Zone 27
Zone 28
Zone 29
Zone 30
Zone 31
Zone 32
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
Zone 33
Zone 34
|___|___|
|___|___|
[324]-[326] Alarm Restore Reporting Codes, Zones 01-34
Section
[324]
[325]
[326]
Zone 01
Zone 02
Zone 03
Zone 04
Zone 05
Zone 06
Zone 07
Zone 08
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
Zone 09
Zone 10
Zone 11
Zone 12
Zone 13
Zone 14
Zone 15
Zone 16
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
Zone 17
Zone 18
Zone 19
Zone 20
Zone 21
Zone 22
Zone 23
Zone 24
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
Zone 25
Zone 26
Zone 27
Zone 28
Zone 29
Zone 30
Zone 31
Zone 32
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
Zone 33
Zone 34
|___|___|
|___|___|
[328] Miscellaneous Alarm Reporting Codes
|___|___|
Duress Alarm
|___|___|
Opening After Alarm
|___|___|
Recent Closing
|___|___|
Future Use
|___|___|
Future Use
|___|___|
Cross Zone/Police Code Alarm
|___|___|
Burglary Not Verified
|___|___|
Alarm Cancelled
[329] Priority Alarm and Restore Reporting Codes
|___|___|
Keypad [F] Fire Alarm
|___|___|
Keypad [A] Auxiliary Alarm
|___|___|
Keypad [P] Panic Alarm
|___|___|
Fail to Report In
|___|___|
Keypad [F] Fire Restore
|___|___|
Keypad [A] Auxiliary Restore
|___|___|
Keypad [P] Panic Restore
|___|___|
Future Use
WWW.DIYALARMFORUM.COM
25
SCW9055/57 Wireless Alarm System
[330]-[332] Tamper Reporting Codes, Zones 01-34
Section
[330]
[331]
[332]
Zone 01
Zone 02
Zone 03
Zone 04
Zone 05
Zone 06
Zone 07
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
Zone 08
|___|___|
Zone 09
Zone 10
Zone 11
Zone 12
Zone 13
Zone 14
Zone 15
Zone 16
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
Zone 17
Zone 18
Zone 19
Zone 20
Zone 21
Zone 22
Zone 23
Zone 24
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
Zone 25
Zone 26
Zone 27
Zone 28
Zone 29
Zone 30
Zone 31
Zone 32
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
Zone 33
Zone 34
|___|___|
|___|___|
Zone 08
[334]-[336] Tamper Restore Reporting Codes, Zones 01-34
Section
[334]
[335]
[336]
Zone 01
Zone 02
Zone 03
Zone 04
Zone 05
Zone 06
Zone 07
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
Zone 09
Zone 10
Zone 11
Zone 12
Zone 13
Zone 14
Zone 15
Zone 16
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
Zone 17
Zone 18
Zone 19
Zone 20
Zone 21
Zone 22
Zone 23
Zone 24
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
Zone 25
Zone 26
Zone 27
Zone 28
Zone 29
Zone 30
Zone 31
Zone 32
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
Zone 33
Zone 34
|___|___|
|___|___|
[338] Miscellaneous Tamper Reporting Codes
|___|___|
General System Tamper
|___|___|
General System Tamper Restore
|___|___|
Keypad Lockout
[339] Closing (Arming) Reporting Codes, Access Codes 1-16
Section
[339]
Code 1
Code 2
Code 3
Code 4
Code 5
Code 6
Code 7
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
Code 8
|___|___|
Code 9
Code 10
Code 11
Code 12
Code 13
Code 14
Code 15
Code 16
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
[341] Miscellaneous Closing (Arming) Reporting Codes
|___|___|
Closing by Master Code 40
|___|___|
|___|___|
Automatic Zone Bypass
Partial Closing
|___|___|
Special Closing
|___|___|
Exit Fault
[342] Opening (Disarming) Reporting Codes, Access Codes 1-16
Code 1
Code 2
Code 3
Code 4
Code 5
Code 6
Code 7
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
Code 9
Code 10
Code 11
Code 12
Code 13
Code 14
Code 15
Code 16
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
|___|___|
[344] Miscellaneous Opening (Disarming) Reporting Codes
|___|___|
26
Opening by Master Code 40
|___|___|
Special Opening
|___|___|
Late to Open
WWW.DIYALARMFORUM.COM
Code 8
5 Advanced Programming
[345] Maintenance Alarm Reporting Codes
[346] Maintenance Restore Reporting Codes
|___|___|
Battery Trouble Alarm
|___|___|
Battery Trouble Restore
|___|___|
AC Failure Trouble Alarm
|___|___|
AC Failure Trouble Restore
|___|___|
Future Use
|___|___|
Future Use
|___|___|
Fire Trouble Alarm
|___|___|
Fire Trouble Restore
|___|___|
Auxiliary Power Supply Trouble Alarm
|___|___|
Auxiliary Power Supply Trouble Restore
|_0_|_0_|
TLM Alarm
|___|___|
TLM Restore
|___|___|
General System Trouble
|___|___|
General System Trouble Restore
|___|___|
General System Supervisory Trouble
|___|___|
General System Supervisory Restore
|_0_|_0_|
System Reset (Cold Start)
[347] Miscellaneous Maintenance Reporting Codes
[348] Test Transmission Reporting Codes
|___|___|
Telephone Number 1 FTC Restore
|___|___|
Walk Test End
|___|___|
Telephone Number 2 FTC Restore
|___|___|
Walk Test Begin
|___|___|
Future Use
|___|___|
Future Use
|_0_|_0_|
DLS Lead IN
|___|___|
Periodic Test Transmission
|_0_|_0_|
DLS Lead OUT
|___|___|
System Test
|___|___|
General Zone Fault Alarm
|___|___|
General Zone Fault Restore
|___|___|
Panel Firmware Update Begin
|___|___|
Delinquency Reporting Code
|___|___|
General Zone Low Battery Alarm
|___|___|
General Zone Low Battery Restore
|_0_|_0_|
Installer Lead Out
|_0_|_0_|
Installer Lead In
|___|___|
Telephone number 3 FTC Restore
|___|___|
Telephone number 4 FTC Restore
|___|___|
Panel Firmware Update Successful
[350] Communicator Format Options
1st Telephone Number
Default 04 |___|___|
2nd Telephone Number
3rd Telephone Number
Default 04
|___|___|
Default
04 |___|___|
4th Telephone Number
Default
04
|___|___|
01 20 BPS, 1400 Hz
05 Future Use
02 20 BPS, 2300 Hz
06* Residential Dial
04 SIA FSK
03 DTMF Contact ID
*Failure to communicate using Residential Dial will not generate an FTC trouble. 3rd phone number follows the format of the 1st if configured for alternate dial.
Call Direction Options
[351] Alarm/Restore Communicator Call Directions
Option 1
First Telephone
Number (Default ON)
Option 2
Second Telephone
Number (Default OFF)


Option 3
Option 4
Third Telephone
Fourth Telephone
Number (Default OFF) Number (Default OFF)


Option 5-8
Future Use
(Default OFF)

[359] Tamper/Restore Communicator Call Directions
Option 1
First Telephone
Number (Default ON)
Option 2
Second Telephone
Number (Default OFF)


Option 3
Option 4
Third Telephone
Fourth Telephone
Number (Default OFF) Number (Default OFF)


WWW.DIYALARMFORUM.COM
Option 5-8
Future Use
(Default OFF)

27
SCW9055/57 Wireless Alarm System
[367] Opening/Closing Communicator Call Directions
Option 1
First Telephone
Number (Default OFF)
Option 2
Second Telephone
Number (Default OFF)


Option 3
Option 4
Third Telephone
Fourth Telephone
Number (Default OFF) Number (Default OFF)

Option 5-8
Future Use
(Default OFF)


[375] System Maintenance Communicator Call Directions
Option 1
First Telephone
Number (Default ON)
Option 2
Second Telephone
Number (Default OFF)


Option 3
Option 4
Third Telephone
Fourth Telephone
Number (Default OFF) Number (Default OFF)

Option 5-8
Future Use
(Default OFF)


[376] System Test Transmissions Communicator Call Directions
Option 1
First Telephone
Number (Default ON)
Option 2
Second Telephone
Number (Default OFF)
Option 3
Third Telephone
Number (Default OFF)
Option 4
Fourth Telephone
Number (Default OFF)
Option 5-8
Future Use
(Default OFF)





[377] Communication Variables
Default
003 002
I_______I______I_______I
Swinger Shutdown (Alarms and Rest)
001-014 Transmissions, 000=disabled
003
I_______I______I_______I
Swinger Shutdown (Tampers and Rest)
001-014 Transmissions, 000=disabled
003
I_______I______I_______I
Swinger Shutdown (Maint. and Rest)
001-014 Transmissions, 000=disabled
000 030
I_______I______I_______I
Communication Delay
000-255 seconds, 000 = No Delay
030
I_______I______I_______I
AC Failure Communication Delay
001-255 minutes/hours, 000=disabled†
010
I_______I______I_______I
TLM Trouble Delay
003-255 seconds x3 (e.g.,003 = 9 seconds)
030
I_______I______I_______I
Test Transmission Cycle (land line)
001-255 days/hours††
060
I_______I______I_______I
Future Use
007
I_______I______I_______I
030
I_______I______I_______I
Delinquency Transmission Delay
000-255 days/hours†††, 000=disabled
000 005
I_______I______I_______I
Communications Cancelled Window
000-255 minutes
Wireless Device Low Battery
Transmission Delay
000-255 days
†Dependent on programming in section [382], option [6].
††Dependent on programming in section [023], option [4].
†††Dependent on programming in section [380], option [8].
i
For UL installations, the Entry Delay plus Communication Delay time must not exceed 60 seconds.
[378] Test Transmission Time of Day
Default
9999
I_______I_______I_______I_______I
Valid entries are 0000-2359 (9999 to disable)
[380] First Communicator Options
Opt
1
Def.
ON
OFF
 
Communications Enabled
 Communications Disabled
2
 Restores on Siren Time-out
 
Restores Follow Zones
3
 Pulse Dialing
 
DTMF Dialing
4
 Future Use
5
 Future Use
28
WWW.DIYALARMFORUM.COM
5 Advanced Programming
6
 Alternating Backup Dialing Enabled
7
 Future Use
8
 Delinquency Follows Zone Activity (Hours)
 
Call Primary Number, Backup to Secondary
 
Delinquency Follows Arming (Days)
[381] Second Communicator Options
Opt
Def.
ON
OFF
1
 Opening After Alarm Keypad Ringback Enabled
2
 Future Use
3
 SIA Uses Programmed Reporting Codes
 
SIA Uses Automatic Reporting Codes
4
 Closing Confirmation Enabled
 
Closing Confirmation Disabled
5
 Future Use
6
 Future Use
7
 Contact ID Uses Programmed Reporting Codes
 
Contact ID Uses Automatic Reporting Codes
8
 Future Use

 Opening After Alarm Ringback Disabled
[382] Third Communicator Options
Opt
Def.
ON
OFF
1
 Future Use
2
 Alarm Communications Enabled During Walk Test*
3
 
Communication Cancelled Message Enabled
 
Alarm Communications Disabled During Walk
Test
 
Communication Cancelled Message Disabled
4
 Call Waiting Cancel Enabled**
 
Call Waiting Cancel Disabled
5
 Alt. Comm. Module Enabled (On for G/D/I models only)
 
Alt. Comm. Module Disabled
6
 AC Failure Transmission Delay Is In Hours
 
AC Failure Transmission Delay is in Minutes
7
 Number of Dialing Attempts is 1 for Residential Dial
 
Residential Dialing Attempts is 5
8
 Future Use
*This option must remain OFF for CP-01 installations.
** A Call Waiting Cancel on a non-Call Waiting line will prevent successful connection to the central station.
[383] Fourth Communicator Options
Opt
Def.
1
2
ON
OFF
 Future Use

 Phone Number 2 Backs Up Number 1
 Phone Number 2 is Independent
3
 Phone Number 3 Backs Up Number 2

 Phone Number 3 is Independent
4
 Phone Number 4 Backs Up Number 3

 Phone Number 4 is Independent
5
 FTC’ed Events Communicate

 FTC’ed Events Do Not Communicate
6

 Account Code Error Check Enabled
7
 Future Use
8
 Remote notification format is SIA
 Account Code Error Check Disabled

 Remote notification format is CID
[389] Alt. Comm. Fault Check Timer
Def.
005
I_______I_______I_______I
Valid entries are 003-255 x 3 (e.g., 003x3 = 9 seconds.)
WWW.DIYALARMFORUM.COM
29
SCW9055/57 Wireless Alarm System
DLS Downloading
[401] First Downloading Options
Opt
ON
OFF
1

Answering Machine/Double Call Enabled
  Answering Machine/Double Call Disabled
2
 
3

Call Back Enabled
 
4

User Initiated Call Up Enabled
  User Initiated Call Up Disabled
5

Future Use
6

300 Baud Panel Call up
7

Future Use
8
 
User Can Enable DLS Window
 User Cannot Enable DLS Window
 
Alternate Communicator DLS Always
Call Back Disabled
110 Baud Panel Call up
 Alternate Communicator Follows DLS Window
[402] DLS Downloading Computer’s Telephone Number (32 Digits)
|___D__|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|
[403] DLS Downloading Access Code / Panel ID Code (Enter 6 Hexadecimal Digits)
Default = 905500 ; For SCW9057 = 905700
|_______|_______|_______|_______|_______|_______|
[404] Panel ID Code (Enter 6 Hexadecimal Digits)
Default = 905500 ; For SCW9057 = 905700
|_______|_______|_______|_______|_______|_______|
[405] Double Call Timer
Default 030
I_______I_______I_______I
Valid entries are 001-255, (000 to disable)
Default 000
I_______I_______I_______I
Valid entries are 000-009, (000 to disable)
[406] Number of Rings To Answer On
[501]-[502] PGM Output Attributes
Program only the following attributes for the PGM options listed. All others are ignored.
Attribute:
 = ON
PGM Option
OFF
00
01
02-04
05
06
07
08
09
Null PGM
Burglary and Fire Siren Output
Future Use
Armed Status
Ready To Arm
Keypad Buzzer Follow
Curtesy Pulse
System Trouble Output (with
trouble options)
10
System Event (with event
options)
11
System Tamper (all sources)
12
TLM and Alarm
13-16 Future Use
17
Away Armed Status
18
Stay Armed Status
19
Command Output #1 (*71)
20
Command Output #2 (*72)
21-39 Future Use
30
1
2
3
4
5
6
7
8
Not Used
Not
Used
True Output
Follows
Timer
Code Req.
Not
Used
Not
Used
Not Used
-
-
Inverted
ON/OFF
No Code
No
No
No
























WWW.DIYALARMFORUM.COM
5 Advanced Programming
Attribute:
1
2
3
4
5
6
7
8
AC Fail
TLM Fault
FTC
Device
Fault
Device
Tamper
Device
Low
Loss of
Clock
Disabled
Disabled
Disabled
Disabled
Disabled





Service
ON Req. Event
OFF
09 System Trouble
Attribute:
ON
OFF
10 System Event
Disabled Disabled Disabled



1
2
3
4
5
6
7
8
Burg.
Event
Fire
Event
Panic Event
Medical
Event
Supervisory
Event
Priority
Event
Duress
Event
Follows
Timer
Latched
Disabled
Disabled
Disabled
Disabled
Disabled








6
7
8
Disabled Disabled Disabled
Section
PGM
PGM Type
1
2
3
4
5
[501]
1
I___I___I
I___I___I
I___I___I
I___I___I
I___I___I
I___I___I
I___I___I I___I___I
I___I___I
[502]
2
I___I___I
I___I___I
I___I___I
I___I___I
I___I___I
I___I___I
I___I___I I___I___I
I___I___I
[591-592] Inactivity Timers 1 & 2 Start and End Times
Section
Default
Start Time
Default
End Time
[591]
Timer #1
9999
I_______I_______I_______I_______I
9999
I_______I_______I_______I_______I
[592]
Timer #2
9999
I_______I_______I_______I_______I
9999
I_______I_______I_______I_______I
Valid times are
00:00-23:59 hours.
9999 to disable
[600] 2-way Audio Control Options 1
Opt
ON
OFF
1
 Tampers Enabled
 
Tampers Disabled
2
 Openings & Closings Enabled
 
Openings & Closings Disabled
3
 
[A] Key Alarm Enabled
 [A] Key AlarmDisabled
4
 
[P] Key Alarm Enabled
 [P] Key Alarm Disabled
5
 
Duress Alarm Enabled (Listen)
 Duress Alarm Disabled
6
 
Opening After Alarm Enabled
 Opening After Alarm Disabled
*7
 Siren Active during 2-way Audio Verification
 
Siren Silent during 2-way Audio Verification
8
 2-Way Audio Is Initiated By The CS Operator
 
2-Way Audio Session Is Immediate
* This option must be ON for UL Listed Installations
[601] 2-way Audio Control Options 2
Opt
ON
OFF
1
 Talk/Listen on Phone #1 Enabled*
 
Talk/Listen on Phone #1 Disabled
2
 Talk/Listen on Phone #2 Enabled*
 
Talk/Listen on Phone #2 Disabled
3
 Talk/Listen on Phone #3 Enabled
 
Talk/Listen on Phone #3 Disabled
4
 Talk/Listen on Phone #4 Enabled
 
Talk/Listen on Phone #4 Disabled
5-8
 Future Use
*When using redundant communications with phone line and alternate communicator, if 2-way audio is enabled, a 2-way voice session is
established over both paths at the same time.
[609] Module Tamper Reporting Codes
I___I___I
Keypad 1 Tamper
I___I___I
Keypad 1 Tamper Restore
I___I___I
Siren 1 Tamper
I___I___I
Siren 1 Tamper Restore
I___I___I
Siren 2 Tamper
I___I___I
Siren 2 Tamper Restore
WWW.DIYALARMFORUM.COM
31
SCW9055/57 Wireless Alarm System
[610] Alternate Communicator Receiver Trouble Reporting Codes
I___I___I
Receiver 1 Trouble
I___I___I
Receiver 1 Trouble Restore
I___I___I
Receiver 2 Trouble
I___I___I
Receiver 2 Trouble Restore
I___I___I
Receiver 3 Trouble
I___I___I
Receiver 3 Trouble Restore
I___I___I
Receiver 4 Trouble
I___I___I
Receiver 4 Trouble Restore
I___I___I
General Alternate Communicator Trouble
I___I___I
General Alternate Communicator Restore
[611] Repeater Tamper/AC Loss Reporting Code
I___I___I
Repeater 1 Tamper
I___I___I
Repeater 1 Tamper Restore
I___I___I
Repeater 2 Tamper
I___I___I
Repeater 2 Tamper Restore
I___I___I
Repeater 3 Tamper
I___I___I
Repeater 3 Tamper Restore
I___I___I
Repeater 4 Tamper
I___I___I
Repeater 4 Tamper Restore
I___I___I
Repeater 1 AC Loss
I___I___I
Repeater 1 AC Loss Restore
I___I___I
Repeater 2 AC Loss
I___I___I
Repeater 2 AC Loss Restore
I___I___I
Repeater 3 AC Loss
I___I___I
Repeater 3 AC Loss Restore
I___I___I
Repeater 4 AC Loss
I___I___I
Repeater 4 AC Loss Restore
INTERNATIONAL PROGRAMMING
[700] Automatic Clock Adjust
Default = 60 |______|_______| Valid Entries 00-99 Seconds
[701] First International Options
Opt Def.
1
ON




2
3
4
OFF
50 Hz AC
Time Base - Internal Crystal
AC/DC Arming Inhibit Enabled
All System Tampers Require Installer Reset
 6-digit User Access Codes
 Busy Tone Detection Enabled
 Future Use
5
6
7-8
60 Hz AC










 4-digit User Access Codes
 Busy Tone Detection Disabled
Time Base - AC Line
AC/DC Arming Inhibit Disabled
All System Tampers Follow Restore
[702] Second International Options
Opt
Def.
1
2
3
4
5
6
7-8

ON







OFF
Pulse Dialing Make/Break Ratio is 33/67

 Pulse Dialing Make/Break Ratio is 40/60
 Force Dialing Disabled



 Standard Handshake
 ID Tone Disabled
 1300 Hz ID Tone
Force Dialing Enabled
Future Use
1600Hz Handshake
ID Tone Enabled
2100 Hz ID Tone
Future Use
[703] Delay Between Dialing Attempts
Default = 003 |_______|_______|_______| Valid entries are 000-255 seconds (entry + 5 seconds)
32
WWW.DIYALARMFORUM.COM
5 Advanced Programming
[800] Door Chime Options for Zones 1-34
Option
1
ON 6 Beeps
OFF Disabled
Section Zone Default
[01]
1
[02]
2
[03]
3
[04]
4
[05]
5
[06]
6
[07]
7
[08]
8
[09]
9
[10]
10
[11]
11
[12]
12
[13]
13
[14]
14
[15]
15
[16]
16
[17]
17

















2
3
4
Option
1
ON 6 Beeps
OFF Disabled
Section Zone Default
Bing Bong Ding Dong Alarm
Disabled Disabled Disabled
Default
Default
Default



















































[18]
18
[19]
19
[20]
20
[21]
21
[22]
22
[23]
23
[24]
24
[25]
25
[26]
26
[27]
27
[28]
28
[29]
29
[30]
30
[31]
31
[32]
32
[33]
33
[34]
34

















2
3
4
Bing Bong Ding Dong Alarm
Disabled Disabled Disabled
Default
Default
Default



















































Note: Chime enable for openings and closings of zones follow the settings in Section [076] Options [1] and [2] when * 4 chime enable.
[804] Wireless programming
[804][001]-[032] Wireless Device Serial Numbers
Zone
Sub Sec. Serial Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
[001]
[002]
[003]
[004]
[005]
[006]
[007]
[008]
[009]
[010]
[011]
[012]
[013]
[014]
[015]
[016]
Zone
|_______|_______|_______|_______|_______|_______|
|_______|_______|_______|_______|_______|_______|
|_______|_______|_______|_______|_______|_______|
|_______|_______|_______|_______|_______|_______|
|_______|_______|_______|_______|_______|_______|
|_______|_______|_______|_______|_______|_______|
|_______|_______|_______|_______|_______|_______|
|_______|_______|_______|_______|_______|_______|
|_______|_______|_______|_______|_______|_______|
|_______|_______|_______|_______|_______|_______|
|_______|_______|_______|_______|_______|_______|
|_______|_______|_______|_______|_______|_______|
|_______|_______|_______|_______|_______|_______|
|_______|_______|_______|_______|_______|_______|
|_______|_______|_______|_______|_______|_______|
|_______|_______|_______|_______|_______|_______|
Sub Sec. Serial Number
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
[017]
[018]
[019]
[020]
[021]
[022]
[023]
[024]
[025]
[026]
[027]
[028]
[029]
[030]
[031]
[032]
|_______|_______|_______|_______|_______|_______|
|_______|_______|_______|_______|_______|_______|
|_______|_______|_______|_______|_______|_______|
|_______|_______|_______|_______|_______|_______|
|_______|_______|_______|_______|_______|_______|
|_______|_______|_______|_______|_______|_______|
|_______|_______|_______|_______|_______|_______|
|_______|_______|_______|_______|_______|_______|
|_______|_______|_______|_______|_______|_______|
|_______|_______|_______|_______|_______|_______|
|_______|_______|_______|_______|_______|_______|
|_______|_______|_______|_______|_______|_______|
|_______|_______|_______|_______|_______|_______|
|_______|_______|_______|_______|_______|_______|
|_______|_______|_______|_______|_______|_______|
|_______|_______|_______|_______|_______|_______|
[804][081] Wireless Supervisory Window
Default
096 EU008 |_______|_______|_______|
Value=Entry x 15 minutes. E.g., 6 x 15 minutes equals 1.5 hours. Valid entries are 4-96 (1 hour -24 hours)
[804][082]-[085] Zone Transmitter Supervision Options
[082]
Opt
1
2
3
4
5
6
7
8
Zone 1-8
[083]
Zone 1








Def.
















Zones 9-16
[084]
Zone 9








Def.
Zone 2
Zone 3
Zone 4
Zone 5
Zone 6
Zone 7
Zone 8








Zones 17-24
[085]
Zone 17








Def.
Zone 10
Zone 11
Zone 12
Zone 13
Zone 14
Zone 15
Zone 16








Zones 25-32
Def.
Zone 18
Zone 19
Zone 20
Zone 21
Zone 22
Zone 23
Zone 24








Zone 25
Zone 26
Zone 27
Zone 28
Zone 29
Zone 30
Zone 31
Zone 32
WWW.DIYALARMFORUM.COM
33
SCW9055/57 Wireless Alarm System
[804][101]-[156] Wireless Key Programming
Enable/Disable
Wireless Key Programming
Sub
Serial Number
Sub
#1
#2
#3
#4
#5
#6
Sub
Def.04
Def.27
Def.30
Def.13
Def.14
Sect. Def.
Sect.
Sect. Def.03
1
[101] |___|___|___|___|___|___|___|___|
[141] |___|___| |___|___| |___|___| |___|___| |___|___| |___|___| [181]
2
[102] |___|___|___|___|___|___|___|___|
[142] |___|___| |___|___| |___|___| |___|___| |___|___| |___|___|
3
[103] |___|___|___|___|___|___|___|___|
[143] |___|___| |___|___| |___|___| |___|___| |___|___| |___|___|
4
[104] |___|___|___|___|___|___|___|___|
[144] |___|___| |___|___| |___|___| |___|___| |___|___| |___|___|
5
[105] |___|___|___|___|___|___|___|___|
[145] |___|___| |___|___| |___|___| |___|___| |___|___| |___|___|
6
[106] |___|___|___|___|___|___|___|___|
[146] |___|___| |___|___| |___|___| |___|___| |___|___| |___|___|
7
[107] |___|___|___|___|___|___|___|___|
[147] |___|___| |___|___| |___|___| |___|___| |___|___| |___|___|
8
[108] |___|___|___|___|___|___|___|___|
[148] |___|___| |___|___| |___|___| |___|___| |___|___| |___|___|
9
[109] |___|___|___|___|___|___|___|___|
[149] |___|___| |___|___| |___|___| |___|___| |___|___| |___|___| [182]
10
[110] |___|___|___|___|___|___|___|___|
[150] |___|___| |___|___| |___|___| |___|___| |___|___| |___|___|
11
[111] |___|___|___|___|___|___|___|___|
[151] |___|___| |___|___| |___|___| |___|___| |___|___| |___|___|
12
[112] |___|___|___|___|___|___|___|___|
[152] |___|___| |___|___| |___|___| |___|___| |___|___| |___|___|
13
[113] |___|___|___|___|___|___|___|___|
[153] |___|___| |___|___| |___|___| |___|___| |___|___| |___|___|
14
[114] |___|___|___|___|___|___|___|___|
[154] |___|___| |___|___| |___|___| |___|___| |___|___| |___|___|
15
[115] |___|___|___|___|___|___|___|___|
[155] |___|___| |___|___| |___|___| |___|___| |___|___| |___|___|
16
[116] |___|___|___|___|___|___|___|___|
[156] |___|___| |___|___| |___|___| |___|___| |___|___| |___|___|
[804][181] Wireless Key 1-8 Enable/Disable
Opt
Def.
1








2
3
4
5
6
7
8
ON








OFF
Key 1 Enabled








Key 2 Enabled
Key 3 Enabled
Key 4 Enabled
Key 5 Enabled
Key 6 Enabled
Key 7 Enabled
Key 8 Enabled
Key 1 Disabled
Key 2 Disabled
Key 3 Disabled
Key 4 Disabled
Key 5 Disabled
Key 6 Disabled
Key 7 Disabled
Key 8 Disabled
[804][182] Wireless Key 9-16 Enable/Disable
Opt
Def.
1








2
3
4
5
6
7
8
ON








OFF
Key 9 Enabled








Key 10 Enabled
Key 11 Enabled
Key 12 Enabled
Key 13 Enabled
Key 14 Enabled
Key 15 Enabled
Key 16 Enabled
Key 9 Disabled
Key 10 Disabled
Key 11 Disabled
Key 12 Disabled
Key 13 Disabled
Key 14 Disabled
Key 15 Disabled
Key 16 Disabled
[804][201] Wireless Keypad Serial Number
Wireless keypad #01 Serial Number
Def.
00000000
|_____|_____|_____|_____|_____|_____|_____|_____|
Def.
00000000
|_____|_____|_____|_____|_____|_____|_____|_____|
[804][202] IT-410 Serial Number
IT-410 Serial Number
[804][301-[302] Wireless Siren Serial Number
[301] Wireless Siren #01 Serial Number
Def.
00000000
|_____|_____|_____|_____|_____|_____|_____|_____|
[302] Wireless Siren #02 Serial Number
Def.
00000000
|_____|_____|_____|_____|_____|_____|_____|_____|
34
WWW.DIYALARMFORUM.COM
































5 Advanced Programming
[804][311] Wireless Siren #1 Options
Opt
Def.
1




2
3
4
5
6
7
8
ON








OFF
Siren Alarm Enabled


















 Tamper Does Not Activate Siren/Strobe While Disarmed
 Pre-Alarm Signal Disabled
Door Chime Enabled
Trouble Beeps Enabled
Squawks Enabled
Enable Strobe
Buzzer Alarm / Strobe Follows BTO
Siren Tamper Enabled
Siren Alarm Disabled








Buzzer Notifications Enabled
Buzzer Notifications Disabled
Door Chime Disabled
Trouble Beeps Disabled
Squawks Disabled
Disable Strobe
Buzzer Alarm / Strobe Follows Alarm Condition
Siren Tamper Disabled
[804][312] Wireless Siren #2 Options
Opt
Def.
1




2
3
4
5
6
7
8
ON








OFF
Siren Alarm Enabled
Buzzer Notifications Enabled
Door Chime Enabled
Trouble Beeps Enabled
Squawks Enabled
Enable Strobe
Buzzer Alarm / Strobe Follows BTO
Siren Tamper Enabled
Siren Alarm Disabled
Buzzer Notifications Disabled
Door Chime Disabled
Trouble Beeps Disabled
Squawks Disabled
Disable Strobe
Buzzer Alarm / Strobe Follows Alarm Condition
Siren Tamper Disabled
[804][320] Global Siren Options
Opt
Def.
1
ON
OFF
 Tamper Activates Siren/Strobe While Disarmed
 Pre-Alarm Signal Enabled
 Future Use
2
3-8
[804][330] Maximum Outdoor Siren Activation Timer
Default
010 |_____|_____|_____|
Valid Entries are 001-255 minutes
[804][401]-[404] Wireless Repeater Programming
[401] Wireless Repeater #01 Serial Number
Def.
00000000
|_____|_____|_____|_____|_____|_____|_____|_____|
[402] Wireless Repeater #02 Serial Number
Def.
00000000
|_____|_____|_____|_____|_____|_____|_____|_____|
[403] Wireless Repeater #03 Serial Number
Def.
00000000
|_____|_____|_____|_____|_____|_____|_____|_____|
[404] Wireless Repeater #04 Serial Number
Def.
00000000
|_____|_____|_____|_____|_____|_____|_____|_____|
i
For Repeater supervision, ensure that dip switch 3 on the repeater is in the OFF state.
[804][900] General Wireless Options
Opt
1
Def.
ON
2-6
7
8
OFF
 Repeater Harsh Placement Test Enabled

 Repeater Harsh Placement Test Disabled

 RF Jam Enabled

Future Use
 RF Jam Disabled
 Future Use
[850] Cellular Signal Strength
Enter [*][8][Installer Code][850] to display the Cellular network signal strength on the SCW9055/57 LCD. Scroll down to view. 5 bars indicates maximum signal strength.
[851] Alternate Communicator Programming
For information regarding programming the alternate communicator, refer to the communicator installation manual.
Special Installer Functions (Accessible through Installer Programming)
[898] Wireless Device Enrollment (See Section 2)
[899] Template Programming (See Section 3)
[900] Panel Version
|______|______|______|______|
Not Programmable (e.g. Ver. 1.0 = 0100)
WWW.DIYALARMFORUM.COM
35
SCW9055/57 Wireless Alarm System
[904]-[907] Wireless Device Placement Test
Enter [*][8][Installer Code][904], [905] [906] or [907] to placement test wireless zones, sirens and repeaters respectively. See “2.3 Wireless
Device Setup” on page 7.
[908] Wireless Modules
Enter [*][8][Installer Code][908] to display all wireless modules enrolled on the system. Scroll to display the name and slot number of each
device. e.g., an indoor siren enrolled on slot one is displayed as 'WT49X1 1'.
[990] Installer Lockout Enable
Enter [990][Installer Code][990]
[991] Installer Lockout Disable
Enter [991][Installer Code][991]
[992] Alternate Communicator Label Broadcast
Enter [992][*]
Note: Perform the alternate communicator label broadcast at the SCW9055/57 main unit.
[996] Restore Wireless Device Programming Factory Defaults
Enter [996][Installer Code][996]
[998] Restore Panel Default Programming
Enter [998][Installer Code][998]
[999] Restore Factory Default Programming
Enter [999][Installer Code][999]
Local Keypad Programming
Enter [] when in Installer Programming to access keypad programming.
[000] Keypad Function Key Programming
Function Key Options
[00] Null Key
[09] Future Use
[25]
[01] Future Use
[10] Future Use
[26]-[32] Future Use
Instant Stay Arm*
[02] Future Use
[11] Future Use
[33]
[03] Stay Arm
[12] Future Use
[04] Away Arm
[13] Command Output #1
[05] [*][9]No Entry Arm
[14] Command Output #2
Night Arm
* Do not use this function key on CP-01 panels
[06] [*][4] Chime On/Off [15] Future Use
[07] Future Use
[16] [*][0] Quick Exit
(See section [804] subsection [141]-[156])
[08] [*][1] Bypass
***Aux Alarm key not intended for medical signals
[17] Reactivate Stay/Away
zones
Default Key 1 Default Key 2
|__0__|__3__|
|__0__|__4__|
Default Key 3 Default Key 4
|__0__|__6__|
Default Key 5
|__0__|__8__|
|__1__|__6__|
[001]-[034] Label Programming (Zone 1-34)
Zone Sub Default
Sect. Z O N E _ _ _ _ X X _ _ _ _
______________
1
[001] |____|____|____|____|____|____|____|____|____|____|____|____|____|____|
Zone Sub
Sect.
10
[010] |____|____|____|____|____|____|____|____|____|____|____|____|____|____|
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
2
[002] |____|____|____|____|____|____|____|____|____|____|____|____|____|____|
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
11
[011] |____|____|____|____|____|____|____|____|____|____|____|____|____|____|
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
3
[003] |____|____|____|____|____|____|____|____|____|____|____|____|____|____|
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
12
[012] |____|____|____|____|____|____|____|____|____|____|____|____|____|____|
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
4
[004] |____|____|____|____|____|____|____|____|____|____|____|____|____|____|
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
13
[13]
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
5
[005] |____|____|____|____|____|____|____|____|____|____|____|____|____|____|
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
36
XX = 01 - 34
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
14
[14]
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
WWW.DIYALARMFORUM.COM
5 Advanced Programming
6
[006] |____|____|____|____|____|____|____|____|____|____|____|____|____|____|
15
[15]
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
7
[007] |____|____|____|____|____|____|____|____|____|____|____|____|____|____|
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
16
[016] |____|____|____|____|____|____|____|____|____|____|____|____|____|____|
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
8
[008] |____|____|____|____|____|____|____|____|____|____|____|____|____|____|
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
17
[017] |____|____|____|____|____|____|____|____|____|____|____|____|____|____|
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
9
[009] |____|____|____|____|____|____|____|____|____|____|____|____|____|____|
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
18
[018] |____|____|____|____|____|____|____|____|____|____|____|____|____|____|
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
19
[019] |____|____|____|____|____|____|____|____|____|____|____|____|____|____|
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
27
[027] |____|____|____|____|____|____|____|____|____|____|____|____|____|____|
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
20
[020] |____|____|____|____|____|____|____|____|____|____|____|____|____|____|
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
28
[028] |____|____|____|____|____|____|____|____|____|____|____|____|____|____|
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
21
[021] |____|____|____|____|____|____|____|____|____|____|____|____|____|____|
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
29
[029] |____|____|____|____|____|____|____|____|____|____|____|____|____|____|
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
22
[022] |____|____|____|____|____|____|____|____|____|____|____|____|____|____|
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
30
[030] |____|____|____|____|____|____|____|____|____|____|____|____|____|____|
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
23
[023] |____|____|____|____|____|____|____|____|____|____|____|____|____|____|
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
31
[031] |____|____|____|____|____|____|____|____|____|____|____|____|____|____|
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
24
[024] |____|____|____|____|____|____|____|____|____|____|____|____|____|____|
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
32
[032] |____|____|____|____|____|____|____|____|____|____|____|____|____|____|
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
25
[025] |____|____|____|____|____|____|____|____|____|____|____|____|____|____|
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
33
[033] |____|____|____|____|____|____|____|____|____|____|____|____|____|____|
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
26
[026] |____|____|____|____|____|____|____|____|____|____|____|____|____|____|
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
34
[034] |____|____|____|____|____|____|____|____|____|____|____|____|____|____|
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
[065] Fire Alarm Label (2 x 14 characters)
Default
F I R E _ Z O N E _ _ _ _ _
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
_ _ _ _ _ _ _ _ _ _ _ _ _ _
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
[066] Fail to Arm Event Message (2 x 16 characters)
Default
S Y S T E M _ H A S _ _ _ _ _ _
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
F A I L E D _ T O _ A R M _ _ _
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
[067] Alarm When Armed Event Message (2 x 16 characters)
Default
A L A R M _ O C C U R R E D _ _
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
W H I L E _ A R M E D _ _ _ < >
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
WWW.DIYALARMFORUM.COM
37
SCW9055/57 Wireless Alarm System
[074] First Keypad Options
Opt
Def.
ON
OFF
1


[F] Key Enabled
 [F] Key Disabled
2
 
[A] Key Enabled
 [A] Key Disabled
3
 
[P] Key Enabled
 [P] Key Disabled
4
 
Quick Arm Prompt ON
 Quick Arm Prompt OFF
5

Quick Exit Prompt ON
6
 
Bypass Options Prompt ON
 Bypass Options Prompt OFF
7
 
User Initiated Call-up Prompt ON
 User Initiated Call-up Prompt OFF
8
 
Hold [P]anic Key Prompt ON
 Hold [P]anic Key Prompt OFF
 
Quick Exit Prompt OFF
[075] Second Keypad Options
Opt
Def.
ON
OFF
1
 
Local Clock Display Enabled
2

3
 
Auto Alarm Scroll Enabled
 Auto Alarm Scroll Disabled
4
 
Language Selection Accessible From Any Menu
 Language Selection Accessible From Installer Only
5

6
 
Power LED Indicates AC Present
 Power LED Indicates AC Absent
7
 
Alarms are Displayed While Armed
 Alarms Are NOT Displayed While Armed
8

 Local Clock Display Disabled
 
Local Clock Displays 24 Hr. Time
 
Power LED Enabled
 
Auto Scroll Open Zones Enabled
Local Clock Displays AM/PM
Power LED Disabled
Auto Scroll Open Zones Disabled
[076] Third Keypad Options
Opt
Def.
1-4
5
6-8
ON
OFF
 Future Use

 Late To Open Prompts Enabled
 Late To Open Prompts Disabled
 Future Use
[077] Programmed LCD Message (2 x 16 Characters)
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
[078] Programmed LCD Message Duration
|____|____|____| Default 003 (Valid entries are 000-255, 000=unlimited message display)
[100] CO Detector Alarm Label (2 x 14 Characters)
Default
CO_ ALARM _ _ _ _ _ _
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
EVACUATE _ A R EA _
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
[101] System Label (2 x 14 Characters)
Default
38
SYSTEM _ _ _ _ _ _ _ _
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
______________
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
WWW.DIYALARMFORUM.COM
5 Advanced Programming
[120] Command Output 1 Label (2 x 14 Characters)
Default
COMMAND _ O/P_ 1 _
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
______________
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
[121] Command Output 2 Label (2 x 14 Characters)
Default
COMMAND _ O/P_ 2 _
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
______________
|____|____|____|____|____|____|____|____|____|____|____|____|____|____|
[996] Label Default
Enter [996][*]
[997] Keypad Version
Enter [997]
Read only (e.g., 1234 = version 12.34)
[998] Initiate Global Label Broadcast
Enter [998][*] Note: Label Broadcast must be initiated by Keypad 1. Note: Label broadcast must be initiated by the SCW9055/57 main
unit.
[999] Reset All Keypad Programming To Factory Defaults
Enter [999][*]
WWW.DIYALARMFORUM.COM
39
SCW9055/57 Wireless Alarm System
5.4 Programming Descriptions
The following is a description of the programming features and options available in the control panel.
[000] Keypad Function Key Programming
The five function keys on the alarm panel can be reprogrammed as described below. See “[001]-[002] Zone Definitions” on page 20 for
defaults.
Option Description
Option Description
[00]
[03]
[04]
[05]
[06]
[08]
[13]
[14] Command Output #2: See [][7][1] on page 12
[16] Quick Exit: See [][0] on page 12
[17] Reactivate Stay/Away Zones: See [][1] on page 10
*[27] Disarm: See Disarm on page 10
*[29] [A]ux Alarm: Same as [A] key
*[30] [P]anic: Same as [P] key
*Applies to wireless keys only (See Section [804] Subsection [61]-[76])
Null Key: Program non functioning keys with this option
Stay Arm: See Stay Arm on page 10
Away Arm: See Away Arm on page 10
No Entry Arm: See [][9] on page 12
Chime On/Off: See [][4] on page 11
Bypass: See [][1] on page 10
Command Output #1: See [][7][1] on page 12
[001]-[002] Zone Definitions
i
Fire zones and 24-Hour zones go into alarm whether the system is armed or disarmed and do not follow the exit delay.
00
Null Zone: This zone type is intended for zones that are NOT used.
01
Delay 1: This zone type follows the Entry Delay 1 and Exit Delay timers programmed in section [005] and is normally used
for entry/exit doors. The exit delay starts as soon as the panel is armed. The zone may be opened and closed during the delay
time without causing an alarm. After the exit delay time has expired, opening the zone starts the entry delay timer. During the
entry delay time, the keypad buzzer sounds steadily to advise the user that the system should be disarmed. If the panel is disarmed before the entry delay expires, no alarm is generated.
02
Delay 2: This zone type operates the same as the Delay 1 [01] zone except it follows the Entry Delay 2 time which is set in
section [005].
03
Instant: This zone type is normally used for door/window contacts, but is instant when opened after the exit delay expires.
04
Interior: This zone type is used with interior motion detectors. Interior zones have an exit delay and an entry delay if a delay
type zone has been violated first. The zone goes into alarm when the entry delay of the delay type zone has expired, if the system has not been disarmed. If the protected area is entered without entering the delayed entrance and an interior zone is violated, an immediate alarm is generated.
05
Interior Stay/Away: If the system is Stay armed, this zone type is bypassed. If the system is Away armed, the zone acts like an
interior type zone [04].
06
Delay Stay/Away: If the system is Stay armed, this zone type is bypassed. If the system is Away armed, this zone will always
follow the entry delay time for Entry Delay 1 when violated.
i
The automatic bypass on Stay/Away type zones is NOT removed by any event other than a valid exit through a delay type 1
zone during the exit delay, arming using the Away function key or by pressing [][1] while armed.
07-08 Future Use
09
24 Hour Supervisory (Hardwired): The zone is similar to a fire zone. Supervision options (NC, EOL, and DEOL) do not
affect the functionality of the zone. The Restored state of this zone type is 5.6 K zone end-of-line, the Alarm state is Short and
the trouble state is Open.
i
This zone type must not be used for wireless zones.
10
24 Hour Supervisory Buzzer: When violated, the system buzzer sounds steadily at medium volume until a valid access code
is entered.
11
24 Hour Burglary: This zone type is active at all times. It reports an alarm if the panel is armed or disarmed. This zone type
sounds the bell for the length of Bell cut-off (section [005]) if the audible attribute is enabled.
12
Future Use
13
24 Hour Gas: Similar to 24 Hour Burglary except for System Event output type and SIA identifier.
14
24 Hour Heat: Similar to 24 Hour Burglary except for System Event output type and SIA identifier.
15
24 Hour Medical: Similar to 24 Hour Burglary except for System Event output type and SIA identifier.
16
24 Hour Panic: Similar to 24 Hour Burglary except for System Event output type and SIA identifier.
17
24 Hour Emergency: Similar to 24 Hour Burglary except for System Event output type and SIA identifier.
40
WWW.DIYALARMFORUM.COM
5.4 Programming Descriptions
18
Future Use
19
24 Hour Water: Similar to 24 Hour Burglary except for System Event output type and SIA identifier.
20
24 Hour Freeze: Similar to 24 Hour Burglary except for System Event output type and SIA identifier.
21
Future Use
22
Momentary Keyswitch Arm: A keyswitch device may be connected to the zone programmed as momentary keyswitch arm.
Momentary activation of the zone alternately arms/disarms the system and silences alarms. Tampers and faults only initiate
their respective trouble sequence. The keypad does not display an indication when this type of zone is activated.
i
With audible alarm active, using the keyswitch when disarmed is the same as entering an access code at the keypad. Using the
keyswitch during the first 30 seconds of a delayed fire alarm is the same as pressing a key at the keypad (the 90 second delay
starts). Violation of a keyswitch zone arms or disarms the system. Violation of this zone type is NOT logged nor is the Police
code transmitted. A bypass on this zone type will not be un-bypassed when the system is disarmed. When the zone is
bypassed, a zone bypass event buffer log and communication occurs immediately, NOT when the system is armed.
23
Maintained Keyswitch Arm (Hardwired): Keyswitch devices can be connected to zones programmed as Maintained Keyswitch arm. In the restored state, the panel is disarmed. Violation of the zone arms the panel. Tampers and faults begin their
associated trouble sequence. If the system is armed with this keyswitch and then disarmed by another method, the keyswitch
zone must be restored and then violated before the system can be armed with this zone again. The same is true for disarming.
If the zone is restored and the system armed, the keyswitch zone must be violated and then restored to disarm the system.
i
This zone type must NOT be used for wireless zones. Activation of a keyswitch zone is intended to arm or disarm the system.
Activation of the zone will not log or transmit the Police code. A bypass on this zone type will not be un-bypassed when the
system is disarmed. When the zone is bypassed, a zone bypass event buffer log and communication occurs immediately, NOT
when the system is armed.
With an audible alarm active, using the keyswitch when disarmed is the same as entering an access code at the keypad. Activating this zone type during the first 30 seconds of a delayed fire alarm is the same as pressing a key at the keypad (the 90 second delay starts). If left in the violated state, the system does not arm until the zone is restored and violated again.
24
Future Use
25
Interior Delay Zone: This zone type is normally used with motion detectors and has a standard exit delay time.
If the panel is Away armed, the Interior Delay Zone is active at the end of the exit delay. The zone then acts like an interior
type zone [04]. If the panel is Stay armed, a violation of this zone type initiates Entry Delay 1. Violating this zone during exit
delay does not cause the system to arm in Away mode, as in regular delay type zones.
26
24 Hour Non-Alarm (or local alarm) Zone: Zones programmed as this type are active at all times but do not cause an alarm
and are not saved in alarm memory. Zone attributes such as Zone Bypassing and Door Chime affect the functionality of this
zone.
i
This zone type sounds the bell, but does not communicate during a walk test. Tampers and faults on zones programmed as 24Hour non-alarm type do not cause alarms.
27-30 Future Use
31
Day Zone: Violating this zone when disarmed sounds the keypad buzzer but does not log or report the events. Violating this
zone when armed sounds the bell and communicates the event.
32
Instant, Stay-Away Zone: This zone is bypassed when the system is Stay armed, but it functions similarly to an Instant Zone
[03] when Away armed. This zone type is useful for motion detectors that must NOT follow the entry delay after a delay zone
is violated, but must still retain the Stay/Away functionality.
33-35 Future Use
36
24-Hour Non-Latching Tamper Zone: This zone generates a tamper condition when violated. This zone is active when
armed or disarmed.
37
Night Zone. This zone acts like an interior Stay/Away zone [05] when the panel is armed in any method except the following.
When the system is armed in Stay mode and the interior zones are reactivated by the user entering [][1], this zone type will
not be activated.
81
24-Hour Carbon Monoxide (CO) Detection. This zone type is used with a wireless CO detector. This zone definition has a
distinct bell cadence in the event of an alarm. The cadence of this alarm is 4 cycles of 100ms on/off pulses, followed by a 5second pause, and then repeated. After 4 minutes the 5-second pause is extended to 60 seconds in duration. The bell is silenced
when an access code is entered or the bell times out.
87
Delayed 24-Hour Fire (Wireless). This zone is used with wireless smoke detectors. This zone functions similar to the standard 24 hour fire zone, except the alarm memory and transmission by the communicator is delayed 30 seconds. If the alarm is
acknowledged by pressing any key within 30 seconds, the bells will silence and the transmission will be aborted. If the smoke
detector is not restored after the alarm has been acknowledged the bell output will activate after 90 seconds. The user then has
another 30-second delay before the bell output latches and communications are activated. A code is then required to silence the
bell output. A tamper or fault of this zone type will cause a fire trouble to log and transmit.
WWW.DIYALARMFORUM.COM
41
SCW9055/57 Wireless Alarm System
i
The fire delay is terminated if a second fire zone is tripped or if the
88
Standard 24-Hour Fire (Wireless). This zone is used with wireless smoke detectors. The bell output will sound instantly to
indicate that the smoke detector has been activated when violated. If enabled, the communicator will immediately transmit the
alarm to the monitoring station. A tamper or fault of this zone type will cause a fire trouble to log and transmit.
i
Zone attributes should NOT be changed from the default settings for all fire type zones.
89
Auto Verified Fire Zone (Wireless) (Required for CP-01). This zone type is to be used with wireless smoke detectors. This
zone definition ensures an alarm condition persists by looking for a second alarm transmission or the absence of an alarm
restoral condition. The system ignores subsequent alarm transmissions after the first transmission from the same zone for a
duration of 40 seconds. If the sensor is in an alarm condition at the end of this 40-second delay, the system will go into full
alarm, sounding the bell, logging and communicating the event. If the zone is in a restored condition at the end of the 40-second delay, the system will start another 80 second verification time sequence. If a fire zone goes into alarm during this period,
the system will go into full alarm, sounding the bell, logging and communicating the event.
i
A tamper or fault of this zone type will cause a fire trouble to log and transmit.
The wireless smoke detector that is used with this zone type must have a built-in siren to act as a pre-alert to the system alarm.
key is pressed during a delay.
Multiple Fire Detections: If another device detects fire during the auto verify or delay sequence, the sequence is immediately
terminated and alarms are generated for all pending zones. This applies to all other fire zones or system
key alarms on the
system (i.e., two fire alarms from different devices on the system will cancel all pending fire delays and create immediate
alarms).
[005] System Timers
After entering Section [005], program the Entry Delay 1, Entry Delay 2 and Exit Delay for the system. Entries are in seconds. Program the Bell Cut-Off Time. Valid entries are in minutes. A value of 000 in the entry or exit delay sections causes a 255 second delay.
A value of 000 in the BTO section produces a 1 minute bell cut-off time. However, these times are displayed as 000.
[006] Installer Code
The default Installer code is [5555] or [555555] if 6-Digit Access Codes is enabled.
[007] Master Code
The master code is a system user code that can program additional access codes, [*][5], and has access to additional user functions,
[*][6]. The default master code is [1234] or [123456] if 6-digit access codes are programmed. See section [701] Opt.[5].
[008] Maintenance Code
The Maintenance Code is a system user code that can only arm and disarm. Any other system function that requires an access code is
not accessible by this code. The default Maintenance code is [AAAA] or [AAAA00] if 6-digit access codes are programmed. See section [701] Opt. 5.
[009] I/O Programming (Zones/PGMs)
The alarm system has two on-board terminals that are programmable as hardwired zones (Zones 33 and 34) or low current PGMs
(PGM1 and PGM2). Enter the 2-digit zone definition or 2-digit PGM option required based on I/O type selected in section [013] option
[1] & [2].
PGM Output Options:
00
Null PGM (Not Used)
01
Burglary and Fire Bell Follower. The PGM switches to ground when any bell activity occurs. This PGM type follows:
•
Fire pre-alerts
•
CO (Carbon Monoxide) alarm signal
•
Temporal three fire signal (if enabled)
•
All burglary and fire alarms
•
Bell cut-off time
This output does NOT follow bell squawks. The main bell still activates for all alarms.
i
Note: The fire bell has precedence over burglary. If a fire alarm occurs when a burglary alarm is active, the fire and burglary
output pulses (“Fire” PGM) with the main bell. This PGM type follows the bell (pulsed if fire, steady if burglary).
02-04 Future Use
05
System Armed Status. The PGM switches to ground at the beginning of the exit delay when the system is armed. The output
goes high (open) when the system is disarmed.
06
Ready to Arm. The PGM switches to ground when the system is ready to arm (all non-force armable zones on the system are
restored). When an access code is entered to arm the system and the exit delay begins, the PGM output is de-activated. This
PGM operates as described during walk test mode (if all zones are restored).
07
Keypad Buzzer Follow. The PGM output switches to ground when the keypad buzzer is activated by the events described
below:
42
WWW.DIYALARMFORUM.COM
5.4 Programming Descriptions
•
24-hour supervisory buzzer zone alarm
•
No activity arm pre-alert
•
Entry delay
•
Audible exit fault
•
Audible exit delay
•
Door chime
The PGM output remains switched to ground while the keypad buzzer is active. This PGM type does not activate for local key
presses or trouble beeps.
Courtesy Pulse. This PGM output switches to ground for 2 minutes past the end of entry or exit times to allow enough time
for complete entry to or exit from the premises. If the system is armed through the No Activity Arming method this output will
NOT activate.
System Trouble. This PGM output switches to ground when any of the selected Troubles are detected. The output de-activates when all of the selected Troubles are restored. The PGM attributes from this output are as follows:
1 Service Required
5 Device (Fire) Fault
2 A.C. Failure
6 Device Tamper
3 Telephone Line Fault
7 Device Low Battery
4 Communications (Failure to Communicate) 8 Loss of Clock
Latched System Event (Strobe). This PGM output switches to ground when any of the selected system events (alarms) occur
on the system. The PGM output deactivates when an access code is entered to disarm the system. If an alarm activates this output
in the disarmed state, the alarm deactivates when a code is entered during bell time-out or if the system arms after bell time-out.
Note: This output activates for all silent and audible alarms.
08
09
10
1 Burglary
2 Fire
3 Panic
4 Medical
5 Supervisory
6 Priority
7 Duress
8 Latched
i
Delay, Interior Delay, Instant, Interior, Stay/Away, Instant Stay/Away, Night, Day Zone and 24-Hour Burg. zones
Key, Fire zone
Key and Panic
Key, Medical and Emergency zones
Supervisory, 24-Hour Buzzer, Auxiliary, Freeze, and Water zones
Gas, Heat, 24-Hour CO zones, 24-Hour Non-latching Tamper
Duress alarms
Follows output timer
Note: This PGM output activates for alarm conditions only. Pre-alerts or delays do NOT activate the output. When this output
follows the output timer, events that have been disabled from activating the output do not restart the timer.
11
System Tamper. This PGM output switches to ground when any Tamper condition occurs on the system. If set for steady
operation, this output de-activates when all Tamper conditions on the system are restored. If this output is set for a pulsed output, the PGM output switches to ground when a Tamper condition occurs and remains on for the duration of the PGM output
timer (programmed in section [170]). This activates for each Tamper condition, even if an un-restored Tamper condition is
present on the system.
Tampers include zone tamper (DEOL), alarm panel case tamper, TLM trouble, RF Jam, and all zone and device tampers.
12
TLM and Alarm. The output activates when a Telephone Line Trouble (TLM) condition is present and then an alarm occurs
on the system.
13-16 Future Use
17
Away Armed Status. This PGM output follows the status of the Stay/Away zones. If the system is armed with the Stay/Away
zones always active, then the Away output is active.
18
Stay Armed Status. This PGM output follows the status of the Stay/Away zones. If the system is armed with the Stay/Away
zones bypassed, then the Stay output is active. Arming in Night mode activates this PGM output.
19
Command Output #1. Entering the [][7][1] command activates the PGM type according to how the PGM attributes are
configured. Refer to sections [501] and [502] for attribute information.
20
Command Output #2. Entering the [][7][2] command activates the PGM type according to how the PGM attributes are
configured. Refer to sections [501] and [502] for attribute information.
21-39 Future Use
[012] Keypad Lockout Options
This section determines how the keypad function operates.
Number of Invalid Codes Before Lockout
Program a number from 000 to 255 to determine the number of invalid master, user or installer access code entries to reach
keypad lockout. When keypad lockout occurs, the system is rendered inoperative via the keypad for the programmed duration
only (wireless keys and keyswitch zones still function). When any keys are pressed, an error tone sounds. Entering 000 disables keypad lockout.
WWW.DIYALARMFORUM.COM
43
SCW9055/57 Wireless Alarm System
Lockout Duration
Program a time from 000 to 255 minutes to determine the length of time before lockout resets and the keypad can once again
be used.
•
If lockout is not reached within the hour roll-over, the number of invalid attempts is reset to 0.
•
After a valid access code is entered, the number of invalid attempts is reset to 0.
•
Fire, Auxiliary and Panic keys are still active during keypad lockout.
•
Key presses do not reset the timer.
•
If the lockout timer was active before powering down, the system lockout is active for the programmed duration on
power up.
[013] First System Options
Option Description
[1]
ON: Hardwired Zone 33 Enabled. Hardwired Zone 33 Input is enabled. The I/O-1 terminal functions as an input for Zone
33. The zone definition is programmed in the first entry of section [009]. Zone supervision is determined by attributes 14, 15,
and 16 programmed in section [133].
OFF: PGM1 Output Enabled. The I/O-1 terminal functions as an output. the PGM type is programmed in the first entry of
section [009]. PGM attributes are programmed in section [501].
[2]
ON: Hardwired Zone 34 Enabled. Hardwired Zone 34 Input is enabled. The I/O-2 terminal functions as an input for Zone
34. The zone definition is programmed in the first entry of section [009]. Zone supervision is determined by attributes 14, 15,
and 16 programmed in section [134].
OFF: PGM2 Output Enabled. I/O-2 terminal functions as an output. the PGM type is programmed in the first entry of section [009]. PGM attributes are programmed in section [502].
[3]-[5] Future Use
[6]
ON: Audible Exit Fault Enabled. If a delay zone is not secured correctly and not force-armed, at the end of the exit delay,
the system goes into entry delay and turns ON the bell output.
OFF: Audible Exit Fault Disabled. The entry delay sounds through the keypad but not the bell.
[7]
Future Use
[8]
ON: Temporal Three Fire Signal Enabled. Temporal Three Fire Signal is used to annunciate fire alarms (½ second ON, ½
second OFF, ½ second ON, ½ second OFF, ½ second ON, 1 ½ seconds OFF).
OFF: Standard Pulsed Fire Signal. The system pulses the bell output (1 second ON, 1 second OFF).
[014] Second System Options
Option Description
[1]
ON: Arm/Disarm Bell Squawk Enabled. The system squawks the bell output once when armed, twice when disarmed and
3 times when disarmed with alarms in memory.
OFF: Arm/Disarm Bell Squawk Disabled. The bell output does not activate.
[2]
Future Use
[3]
ON: RF Jam Logs after 5 Minutes. The system logs an RF Jam trouble condition if the condition is present for 5 minutes.
OFF: RF Jam Logs after 20 Seconds. The system logs the trouble condition after 20 seconds.
i
The trouble is displayed on the keypad as soon as it occurs. The panel Trouble LED changes from yellow to orange indicating
the presence of an RF jam.
[4]
ON: Aux Boost Enabled: When the system is in Power Save mode, (AC Trouble) Aux+ output voltage is regulated 12VDC.
OFF: Aux Boost Disabled: Aux+ output voltage is not regulated.
[5]
Future Use
[6]
ON: Audible Exit with Urgency. The keypad beeps once every second, and 3 times a second during the last 10 seconds, during exit delay when the system is armed with a user code or armed in the Away mode. This option always on for CP-01.
OFF: Silent Exit Delay. The keypad does not beep during exit delay.
[7]
Future Use
[8]
ON: Fire Bell is Continuous. The bell output does not time out if a fire alarm occurs. The User must turn off the bell by
entering a valid user code.
OFF: Fire Bell follows Bell Cut-off. The bell output times out normally.
i
44
Only zone definitions [87], [88], and [89] (along with the [F] Key) use this signalling.
WWW.DIYALARMFORUM.COM
5.4 Programming Descriptions
[015] Third System Options
Option Description
[1]
i
ON: Fire Key Enabled. Pressing and holding the fire
key for 2 seconds generates a fire alarm. The keypad sounds a set
of 3 beeps to acknowledge the valid alarm and the buzzer sounds a pulsing alarm tone for the length of the bell time-out, or
until an access code is entered. An alarm reporting code (if programmed) is transmitted.
OFF: Fire Key Disabled. The Fire
key does not sound or report an alarm when pressed.
When enabled, this key generates alarms at all times.
[2]
ON: Panic Key Audible. When a valid Panic key
alarm is generated, the keypad buzzer sounds a series of 3 beeps to
acknowledge the alarm. The buzzer then sounds a steady tone for the length of the bell time-out or until an access code is
entered.
OFF: Panic Key Silent. When a valid Panic key
alarm is generated, the keypad buzzer and the bell output remain
silent, but the alarm is still transmitted (if programmed).
[3]
ON: Quick Exit Enabled. See [][0] in section 3.3 [] Commands.
OFF: Quick Exit Disabled.
[4]
ON: Quick Arming Enabled/Function Keys Do Not Require Code. [][0] arming and Stay/Away function keys may be
used to arm the system without the entry of a valid access code. Wireless keys not associated to a user code may also be used.
OFF: Quick Arming Disabled/Function Keys Require Code. [][0] arming is not permitted, and Stay/Away function
keys require the entry of an access code to arm the system.
i
This option must be OFF to identify wireless keys for arming.
[5]
ON: Code Required for Bypassing. After entering the [][1] Bypass Zones command, an access code must be entered
before zones may be bypassed.
OFF: No Code Required. No code is required to enter the [][1] Bypass Zones command to bypass zones.
[6]
ON: Master Code Not Changeable. The Master Code (access code 40) may not be changed by the user with [][5] access
code programming. The Master Code can only be programmed in Installer Programming, section [007].
OFF: Master Code Changeable. The Master Code (access code 40) may be programmed by the user using the
[][5][Master Code][40] command. The Master Code may also be programmed in Installer Programming.
[7]
ON: TLM Enabled. The Telephone Line Monitor function is active and the system indicates if a Telephone Line Trouble
condition exists when using the [][2] View Trouble Conditions command.
OFF: TLM disabled. The Telephone Line Monitor function is shut off and telephone line troubles are NOT indicated by the
system.
[8]
ON: System Tamper Enabled. The panel monitors the physical tamper switch. The switch activates if the system is taken
off the wall, or the front cover is removed, generating a System Tamper Alarm. A system tamper causes an audible alarm if
the system is armed. If the system is disarmed when a system tamper occurs, the system cannot be armed until the tamper
condition is cleared.
OFF: System Tamper Disabled. The panel does not monitor the physical tamper switch.
[016] Fourth System Options
Option Description
[1]
ON: Cross Zoning Enabled. The panel uses the Cross Zone attribute for burglary verification.
OFF: Police Code Enabled. The panel uses the Police Code feature for burglary verification.
[2]
ON: Exit Delay Restart Enabled. (Only available on CP-01 panels) If a delay zone (Delay 1 or 2 only) is violated during
the exit delay and then restored, it is considered an exit. If a delay zone is violated again it is considered a re-entry. With
this option enabled the panel restarts the exit delay. Further violations and restores of delay zones do not restart the exit
delay.
OFF: Exit Delay Restart Disabled. Delay zone violations and restores do not restart the exit delay.
i
The exit delay can only be restarted once. This includes restarts from Away function keys. If the exit delay is silent, the additional exit time remains silent and doubles the programmed exit time (required for CP-01).
[3]
ON: Blank Keypad When Not Used. If no keys are pressed for 30 seconds, the display and all keypad lights except backlighting (if enabled) turn OFF until the next keypress, entry delay, audible alarm, or keypad buzzer condition.
OFF: Keypad Always Active. The keypad lights remain ON at all times.
[4]
ON: Code required to remove Keypad Blanking. A valid access code must be entered before a blanked keypad can be
used. If the bell or entry delay is active, entering an access code un-blanks the keypad and disarms the system.
OFF: No Code Not Required. Pressing any key on a blanked keypad removes the blanking. If the key is a number, then it
is considered the first digit of an access code.
WWW.DIYALARMFORUM.COM
45
SCW9055/57 Wireless Alarm System
[5]
ON: Keypad Backlighting Enabled. Keypad backlighting is continuously on.
OFF: Keypad Backlighting Disabled. Keypad backlighting is never on.
[6]
Future Use
[7]
ON: Bypass Status Displayed While Armed. “Warning Bypass Active” displays if zones are manually bypassed when the
system is Away armed.
OFF: Bypass Status Not Displayed While Armed. Zones that have been manually bypassed are not indicated when the
system is Away armed.
[8]
ON: Daylight Saving Time Enabled. The panel switches between daylight-saving and standard time according to the programmed time of the year and number of hours in sections [168] and [169].
OFF: Daylight Saving Time Disabled. The panel will NOT make time adjustments for daylight-saving time.
[018] Sixth System Options
Option Description
[1]
Future use
[2]
ON: Keypad Tampers Enabled. All system keypads generate tamper troubles and restores.
OFF: Keypad Tampers disabled. System keypads do NOT generate tamper troubles and restores.
[3]-[4] Future use
[5]
ON: Keypad Buzzer Follows Siren Enabled. The keypad buzzers follow the bell status.
OFF: Keypad Buzzer Follows Siren Disabled. The keypad buzzers do NOT follow all bell activity. Only designated
alarms will activate the keypad buzzer.
[6]-[8] Future use
[023] Tenth System Options
Option Description
[1]
On: Chime on Openings Enabled. When a zone with the door chime attribute ON is violated, the system keypads and sirens
(if enabled) sound door chime beeps.
Off: Chime on Openings Disabled. When a zone with the door chime attribute ON is violated, the system keypads and
sirens (if enabled) do not sound door chime beeps.
[2]
On: Chime on Closings Enabled. When a zone with the door chime attribute ON is restored, the system keypads and sirens
(if enabled) sound door chime beeps.
Off: Chime on Closings Disabled. When a zone with the door chime attribute ON is restored, the system keypads and sirens
(if enabled) do not sound door chime beeps.
[3]
ON: Test Transmission While Armed Only. The Test Transmission reporting code is only transmitted if the system is
armed at the time it is programmed to report the event.
OFF: Test Transmission while Armed/Disarmed. The system always reports the Test Transmission reporting code at the
programmed time.
[4]
ON: Transmission Counter in Hours. The system changes the Test Transmission Reporting Cycle Time from Days to
Hours.
OFF: Transmission Counter in Days. The Test Transmission Reporting Cycle Time is in Days.
[5]
ON: Switching From Away to Stay Disabled. The user can NOT switch from Away Arm mode to Stay Arm mode using the
function keys.
OFF: Away to Stay Toggle Option Permitted. The user can switch arming modes.
[6]
ON: New Alarms will not Disconnect 2-way Audio. The system does not disconnect a listen in/two-way session if an alarm
occurs.
OFF: New Alarms Disconnect 2-way Audio. The system disconnects a listen in/two-way session. New events are transmitted after the session ends.
i
This option must be OFF for UL listed installations. Applies to SCW9057 only.
[7]
ON: Trouble Beeps are Silent. The system does NOT activate the keypad buzzer for any trouble condition except fire.
OFF: Trouble Beeps Sound Every 10 Seconds. The system annunciates troubles via the keypad buzzer (2 beeps every 10
seconds).
[8]
ON: Keyswitch Arms in Away Only. Keyswitch zones on the system always arm in Away mode.
OFF: Keyswitch Arms in Stay or Away. When a keyswitch zone is used to arm the system, the final armed mode depends
on whether the user trips a delay zone during exit delay. If the user trips a delay zone, the system arms in Away mode; If not,
the system arms in Stay mode. This is similar to arming the system at the keypad with an access code. The exit delay is audible.
46
WWW.DIYALARMFORUM.COM
5.4 Programming Descriptions
[024]
Eleventh System Options Code
Option Description
[1]
[2]
[3]
[4]
i
ON: Temperature Display Enabled. The keypad displays the temperature received from the lowest numbered external
siren. If the local clock display is also enabled, then the keypad displays date, time, and temperature.
OFF: Temperature Display Disabled. The keypad does NOT display the temperature.
ON: Temperature displayed in Celsius. The keypad displays the temperature in Celsius.
OFF: Temperature displayed In Fahrenheit. The keypad displays the temperature in degrees Fahrenheit.
ON: Internal Siren Enabled. The internal siren on the panel is enabled.
OFF: Internal Siren Disabled. The internal siren on the panel is disabled.
ON: Inactivity Monitored by all Zones. If no violations occur on any burglary zones during the Inactivity Timer windows
(section [591]-[592]), the panel communicates the Fail to Report In code, if programmed.
This code is not transmitted for panels that are Away armed. Troubles and bypassed zones will not cause activity indications.
OFF: Inactivity Monitored only by 24-hour Non-alarm Zones. If no violations occur on a 24-hour non-alarm zone during
the Inactivity Timer windows (section [591]-[592]), the panel communicates the Fail to Report In code, if programmed.
[5]
ON: Enable Realtime Clock: The panel sends a request to the alternate communicator module for real time/date synchronization at midnight or when the panel clock time is lost. The updated time/date is displayed on the panel LCD.
OFF: Disable Realtime Clock: The panel uses the local time setting as system time.
[6]-[8] Future Use
[030] Zone Loop Response Options
This section is used to determine the Loop Response Time for hardwired zones 33 and 34.
Option
Description
[1]
ON: Zone 33 is Fast Loop Response: Zone 33 has a fast loop response (36 ms).
OFF: Zone 33 is Normal Loop Response: Zone 33 has a normal loop response (400 ms).
[2]
ON: Zone 34 is Fast Loop Response: Zone 34 has fast loop response (36 ms).
OFF: Zone 34 is Normal Loop Response: Zone 34 has normal loop response (400 ms).
[3]-[8] Future Use
[101]-[134] Zone Attributes
The following options can be enabled or disabled for each zone. Pressing [9] in one of these sections brings the installer to the upper
bank (attributes 9 to 16). From the upper bank, press [9] to return to the lower bank (attributes 1 to 8).
i These attributes override default settings. Do NOT change fire zone attributes from their default settings.
Option Description
[1]
Audible siren
ON: An alarm activates the Siren.
OFF: Silent alarm.
[2]
Steady or Pulsed- ON: The bell output is steady when the zone is in alarm.
Bell Type
OFF: The bell output pulses when the zone is in alarm.
[3]
Chime
ON: The keypad chimes when the zone is violated and when the zone is secured.
OFF: The zone does not chime the keypad.
[4]
Bypass
ON: The zone may be manually bypassed.
OFF: The zone can not be bypassed.
[5]
Force Arming
ON: The system can be armed with the zone violated. The zone is temporarily bypassed and, when
secured, is monitored by the system.
OFF: The system cannot be armed if the zone is open.
[6]
Swinger
ON: When the zone goes into alarm for the number of times programmed in the Swinger Shutdown
Shutdown
Counter (see section [377]), it shuts down with no further transmissions sent to the monitoring station.
The bell follows Swinger Shutdown if programmed.
OFF: Swinger Shutdown is disabled. All alarms are transmitted and do not follow the Swinger Shutdown
Counter.
If a zone is in Swinger Shutdown, and this attribute is disabled, then re-enabled, the zone will no longer be in Swinger Shuti down.
[7]
Transmission
ON: Reporting of zone alarms are delayed for the programmed time in section [377] after the zone goes
Delay
into alarm. If a valid access code is entered within this time, no alarm signal is communicated.
OFF: When an alarm occurs, the reporting code is transmitted immediately.
[8]
Cross Zone
ON: The zone is enabled for cross zoning.
OFF: The zone is not enabled for cross zoning.
[9]
2-way Audio
ON: The zone will initiate a 2-Way Audio Verification session with the Central Station.
OFF: This zone will not initiate a 2-Way Audio session (applies to hardwired zones 33 & 34 only).
WWW.DIYALARMFORUM.COM
47
SCW9055/57 Wireless Alarm System
[10]
Talk-Listen/Listen-in Only
ON: The zone initiates a 2-way session with the central station. Both microphone and speaker are activated. This option is only available when zone attribute [9] is enabled.
OFF: The zone initiates a Listen-in only session with the central station. Only the microphone is activated. This option is only available when zone attribute [9] is enabled.
[11]Future Use
[13]
Options [14] to [16] are used for zones 33 and 34 exclusively. If more than 1 option is enabled for options 14, 15, and 16 the lowest
attribute number will take precedence. If Options 14 and 15 are both enabled the zone follows the NC loop configuration.
[14]
Normally Closed ON: The zone follows the Normally Closed (NC) loop configuration.
Loops
OFF: The zone does NOT follow NC loop configuration.
[15]
Single End of
ON: The zone follows the SEOL zone configuration.
Line (SEOL)
OFF: The zone does NOT follow SEOL zone configuration.
Resistors
[16]
Double End of
ON: The zone follows the DEOL zone configuration.
Line (DEOL)
OFF: The zone does NOT follow DEOL zone configuration.
Resistors
When Zone Types (section [001] to [002]) are programmed, the system changes the zone attributes to those found in the
i chart included in the Programming Worksheets. The Zone Attributes will default if a new Zone Type is programmed for a
specific zone.
Ready light ON:Program attributes [1-8]
Ready light and Armed light ON:Program attribute [9-16] (press [1] for option 9, press [6] for option 14 etc.)
Press [9] to switch between attributes [1-8] and attributes [9-16].
[167] Alt. Comm. Communications Wait for ACK
This value represents the time the communicator waits for an acknowledgement (ACK) from the receiver after sending the SIA or
CID packet to the central station. If this timer expires before acknowledgement is received, the SCW re-transmits the Packet and
increments the number of failed dialing attempts.
[168] Daylight Saving Time Begin
These sections are used to program the date, time and increment that the clock moves ahead for Daylight Saving Time each year. The
following attributes can be programmed:
Month
[001] to [012] represents January to December.
Week
[000] indicates that the day of the month is programmed in the Day section below. [001] to [005] represents weeks
1 to 5 of the month. Week 5 always represents the last week in the month, regardless of whether the number of
weeks in the month is 4 or 5.
Day
[001] to [031] represents the day of the month if [000] was programmed in the Week section above. If [001] to
[005] was programmed in the Week Section above, then [000] to [006] represents Sunday to Saturday.
Hour
[000] to [022] represents the hour that Daylight Saving Time takes effect.
Increment
[001] to [002] represents the number of hours to advance the clock for Daylight Savings Time.
i
Do not program the Hour outside of the valid range or the time will not change.
Do not program the value of the Increment to be greater then the number of hours remaining in the current day.
[169] Daylight Saving Time End
These sections are used to program the date, time and increment that the clock moves back for Standard Time each year. The following
attributes can be programmed:
Month
Week
Day
Hour
Increment
i
[001] to [012] represents January to December.
[000] indicates that the day of the month is programmed in the Day section below. [001] to [005] represents weeks
1 to 5 of the month. Week 5 always represents the last week in the month, regardless of whether the number of
weeks in the month is 4 or 5.
[001] to [031] represents day of the month if [000] was programmed in the Week section above. If [001] to [005]
was programmed in the Week Section above, then [000] to [006] represents Sunday to Saturday.
[000] or [023] represents the hour that Standard Time takes effect.
[001] or [002] represents the number of hours to roll back the clock for Daylight Saving Time.
If Daylight Saving Time occurs at Midnight program the time 2:00AM.
[170] PGM Output Timer
Program the time, in seconds, PGM outputs programmed to follow the PGM Output Timer will activate for. Valid entries are [001] to
[255].
48
WWW.DIYALARMFORUM.COM
5.4 Programming Descriptions
[176] Cross Zone/Police Code Timer
Program the time, in seconds (Cross Zone) or minutes (Police Code), that the panel uses to determine if a Cross Zone or Police Code
event has occurred. If [000] is programmed when using the Police Code feature, the panel generates a Police Code event (if any two
zones go into alarm during an armed-to-armed period). Valid entries are [001] to [255].
[190] No Activity Arming Pre-Alert
Program the time, in minutes, for the No Activity Arming Pre-Alert Duration. The keypad provides a steady tone warning the user that
the system is arming. The user can either violate a zone or press any key to abort the arming sequence. Valid entries are [000] to [255].
[191] No Activity Arming Timer
Program the time, in minutes, for the No Activity Arm Timer. If Delay Zones are restored and no zone activity is detected for the time
programmed, the auto arm sequence starts. Valid entries are [000] to [255].
[202]-[206] Zone Assignments
Activates the selected zones. Zones 1-32 are ON by default. Zones 33, 34 are OFF by default. If a zone is enabled, it is supervised and
operates according to the zone type programmed. If a zone is not assigned, it is not supervised and all activity on the zone is ignored by
the panel.
If a zone assignment is set, but no serial number is enrolled (zones 1 to 32), or the terminals are set as PGM outputs instead
of zone inputs (zones 33 and 34), then these zones appear in the bypass list.
i
[301]-[303] Communication Telephone Numbers
The information in this section also applies to sections [302], [303] and [305].
These sections determine which type of communicator is activated in the event of an alarm (telephone, Cellular and Ethernet) and the
sequence that the system follows in the event of an unsuccessful communication.
• Entry of [D] followed by a [Telephone Number] terminated with “F” configures the section for telephone dialing.
E.g.: [D12223334444F]
• Entry of [D] followed by [CAA] terminated with “F” allows the system configuration to be determined by the alternate communicator module.
E.g.: [DCAAF]
• Enter [DCBBF] to configure the section for Ethernet Receiver 1
• Enter [DCCCF] to configure the section for Ethernet Receiver 2
• Enter [DCDDF] to configure the section for Cellular Receiver 1
• Enter [DCEEF] to configure the section for Cellular Receiver 2
Telephone Communications
All telephone number sections are 32 digits in length. Hexadecimal digits may be programmed in the telephone number to perform
additional functions as follows:
Enter [][2][] – HEX B to dial “”
Enter [][3][] – HEX C to dial “#”
Enter [][4][] – HEX D for an additional dial tone search, as is required for PBX telephone systems
Enter [][5][] – HEX E to insert a 2-second pause in the telephone number
i
There is an automatic 2-second pause before additional dial tone searches are initiated.
HEX A is not used.
HEX F represents the end of the phone number (everything after F is ignored).
Pressing [#] in these sections exits and saves the entire phone number.
The panel does not attempt to communicate if no phone number is programmed. This applies to phone numbers 1 and 2.
[304] Call Waiting Cancel String
Program the digits required to disable call waiting. If enabled, the system dials the programmed string on the first dialing attempt.
Program unused digits with data [F]. This section is activated in Section [382] Opt [4].
[305] Fourth Telephone Number
See [301]-[303] Communication Telephone Numbers for details.
[310] System Account Number
Program the System Account Number. Only the SIA format supports 6-digit account numbers. If a 4-digit account number is required,
program the last two digits as data [FF]. For formats other than SIA, program a HEX [A] for any digit [0] in the account number being
used.
Auto Sync with Alternate Communicator
If the panel detects an alternate communicator module, it automatically synchronizes the system account code with programming section [021] of the alternate communicator. Account codes of FFFFXX and 0000XX are not permitted. Synchronization takes place when
Installer Programming is exited or DLS disconnects.
WWW.DIYALARMFORUM.COM
49
SCW9055/57 Wireless Alarm System
[320]-[326] Alarm Reporting Codes
These reporting codes are used by the communicator to transmit zone alarms and restores for zones 1 to 34.These reporting codes are
sent to the Alarm & Restore call direction group
.
i
Zone alarms transmit to the System Test Transmission Call Direction when they are being transmitted as part of the walk
test (enabled if section [382] option [2] is ON).
[328] Miscellaneous Alarm Reporting Codes
Duress Alarm
This reporting code is transmitted whenever a Duress code is used to perform any function on the system. The reporting code is sent to
the Alarm & Restore call direction group.
Opening After Alarm
This reporting code is transmitted when the system is disarmed after an alarm; if an alarm occurred during the previous armed period.
The reporting code is sent to the Alarm & Restore call direction group.
Burglary Not Verified
When Cross Zoning (section [016] option [1]) is enabled, this reporting code is sent if the Cross Zone timer is initiated by the first cross
zone alarm, but it is not verified by a second cross zone alarm before the timer expires. This reporting code is sent to the Alarm &
Restore call direction group.
Alarm Cancelled
If an alarm event is sent after transmission delay has expired, a cancel window time starts. This event is logged and transmitted if a valid
access code is entered any time during this window. When this reporting code/event has been acknowledged by the central station, a
keypad will ring back. This reporting code is sent to the Alarm & Restore call direction group. See section [377] Communications Cancel Window.
[329] Priority Alarm and Restore Reporting Codes (Fire, Auxiliary, Panic Alarms/Restores and Fail to Report In)
If enabled and used to generate manual alarms, these reporting codes are sent to the Alarm & Restore Call Direction group.
[330]-[336] Tamper/Restore Reporting Codes, Zones 01-34
These reporting codes are used by the communicator to transmit zone tampers and restores for zones 1 to 34. These reporting codes are
sent to the Tamper Alarm & Tamper Restore call direction group of the system.
[338] Miscellaneous Tamper Reporting Codes
General System Tamper & Restore
These reporting codes are sent to the system Tamper Alarm & Tamper Restore call direction group when a panel tamper occurs.
Keypad Lockout
Whenever the system enters keypad lockout, this reporting code is sent to the system Tamper Alarm & Tamper Restore call direction
group.
[339] Closing (Arming) Reporting Codes (Access Codes 1-16)
When the system is armed, a closing reporting code is transmitted after the exit delay expires for the user code that armed the system.
These reporting codes are sent to the Opening & Closing call direction group of the system. In addition, either “Armed in Stay Mode”
or “Armed in Away Mode” is logged to the event buffer.
Closing by Users (Duress)
When the system is armed by an access code programmed as duress, the corresponding closing reporting code is transmitted. This
reporting code is sent to the Opening & Closing call direction group.
[341] Miscellaneous Closing (Arming) Reporting Codes
Closing By Master Code 40
See [339] Closing by Users 1-16.
Automatic Zone Bypassing
This stops transmission of zone bypass information for systems set up for an automatic communication format (SIA and Contact ID).
Enter [00] to disable the automatic zone bypassing communications. If the zones are to be identified, they are transmitted with the Partial Closing to the Opening & Closing call direction group. (24 Hour zone types transmit that they have been bypassed when the user
exits the bypassing menu).
Partial Closing
If zones were manually bypassed at the time of arming, this reporting code is transmitted to the central station with the Closing code to
warn of a security compromise. Automatic bypasses caused by Stay arming do not cause this code to be transmitted. Zones force armed
by automatic arming transmit in the manner described above. If SIA is used, each zone is identified using the UB-XX (un-typed bypass)
identifier. The identified zones follow the partial closing code and precede the closing transmission. This reporting code is sent to the
Opening & Closing call direction group.
Special Closing
This reporting code is transmitted if the system is armed without an access code using Keyswitch Zone, Downloading, Quick Arm
[][0], or Stay or Away function keys. In addition, either “Armed in Stay Mode” or “Armed in Away Mode” is logged to the event buffer for all closing types. This reporting code is sent to the Opening & Closing call direction group.
50
WWW.DIYALARMFORUM.COM
5.4 Programming Descriptions
Exit Fault
If an Exit Error occurs and entry delay expires before the system is disarmed, this reporting code is sent. This reporting code is sent to
the Openings & Closings call direction group
.
i
If the delay zone that caused the exit error has cross zoning enabled, the exit fault and zone alarm still transmit if a second
zone is not violated. This is to inform the central station that the premise is not secure. The local alarm sequence follows
the cross zoning rules. The exit error is transmitted with the zone alarm that caused the fault, even if that zone has a transmission delay enabled.
[342] Opening (Disarming) Reporting Codes (Access Codes 1-16)
When the system is disarmed, an opening Reporting code for the corresponding user is transmitted.
These reporting codes are sent to the Opening & Closing call direction group.
Opening by Users (Duress)
An opening by an access code programmed as duress results in a transmission of the corresponding opening reporting code. These
reporting codes are sent to the Opening & Closing call direction group.
[344] Miscellaneous Opening (Disarming) Reporting Codes
Opening By Master Code 40
See [342] Opening (Disarming) by Users 1-16.
Special Opening
If the system is disarmed (opened) by using keyswitch zone, an unidentified wireless key, or downloading, this reporting code is transmitted to the Opening & Closing call direction group.
[345]-[346] Maintenance Alarm Reporting Codes
Battery Trouble & Restore
This trouble is reported if the standby battery is low or disconnected. These reporting codes are sent to the System Maintenance call
direction group.
AC Failure Trouble & Restore
If the AC supply has failed or has been restored, these reporting codes are sent. A programmable delay (001-255 minutes, section [377])
applies to both the trouble and the restore. These reporting codes are sent to the System Maintenance call direction group.
Fire Trouble & Restore
An open circuit or any Low Sensitivity, Tamper or Fault report from a wireless smoke detector, causes this trouble to be reported. These
reporting codes are sent to the System Maintenance call direction group.
Auxiliary Power Supply Trouble & Restore
If an auxiliary voltage supply trouble occurs (the Aux PTC has caused the auxiliary supply to stop outputting power), this trouble is
reported within 60 seconds. These reporting codes are sent to the System Maintenance call direction group.
i
When the Aux Positive Temperature Co-efficient (electronic fuse) enters the open state due to a short or high current draw,
if the short is removed and a load is still applied, the Aux+ output will not recover. It must be powered down and back up
again to restore this condition.
TLM Alarm
The TLM Restore code is sent when the telephone trouble condition is restored. This reporting code is sent to the System Maintenance
call direction group.
General System Trouble & Restore
These reporting codes are transmitted via System Maintenance call direction group to report RF Jam troubles or hardware fault troubles
that occur on the system.
General System Supervisory Trouble & Restore
These reporting codes are transmitted via the System Maintenance call direction group when an enrolled TLXXX module has been
detected as absent or restored.
System Reset (Cold Start)
In the event of a total power failure, the Cold Start reporting code is transmitted to the central station when power is restored to the
panel. The reporting code is sent after 2 minutes to allow the panel to stabilize, although the event is logged in the buffer at 00:00. An
entry of 00 in this section disables the reporting code.
[347] Miscellaneous Maintenance Reporting Codes
Failure to Communicate (Phone Numbers 1, 2, 3 & 4)
When events fail to communicate to either telephone number, this reporting code is transmitted the next time a communication is successful. The information is transmitted in the following order:
•
Old Event(s)
•
Failure To Communicate (Phone #1)
•
New Event(s)
The FTC reporting code does not follow any call direction “group.” It is sent to every group’s call directions upon transmission of
“failed to communicate” events. When event(s) fail to communicate to a telephone number, no attempt to communicate is made again
until another event is sent to that phone number.
WWW.DIYALARMFORUM.COM
51
SCW9055/57 Wireless Alarm System
DLS Lead In and Lead Out
When call-back is enabled, the control panel transmits the DLS Lead In reporting code before calling back the downloading computer.
The DLS Lead Out reporting code is transmitted by the panel every time DLS has completed a successful DLS session with the control
panel. The DLS Lead In reporting code is transmitted in two ways: after the panel has been successfully called by DLS, but before the
panel calls DLS back via the downloading telephone number when call-back is enabled, or upon a user-initiated call-up. These reporting codes are sent to the System Maintenance call direction group.
i
If DLS is terminated by an alarm, the alarm system will not communicate the DLS lead out event.
General Zone Fault & Restore
This reporting code is sent whenever a zone has entered the fault state. This occurs when there is a short on DEOL hardwired zones and/
or a loss of supervisory on a wireless zone. These reporting codes are sent to the System Maintenance call direction group.
Panel Firmware Update Begin/Successful
This reporting code is sent to the central station before the panel starts a firmware upgrade and after it has been successfully completed.
Delinquency Reporting Code
The Delinquency Reporting code is transmitted in one of two ways. If section [380] option [8] is OFF, it is transmitted when the system
has not been armed for the number of days programmed in section [377]. If section [380] option [8] is ON, it is transmitted when no
zone activity has been detected on the system for the number of hours programmed in section [377]. This reporting code is sent to the
System Maintenance call direction group.
i
The Activity Delinquency timer is active when the system is armed in Stay mode, and not active in Away mode or Night
mode arming.
General Zone Low Battery Alarm and Restore Codes
The following reporting codes are sent to report a Zone Low Battery condition on wireless zones. Individual zones are logged to the
event buffer. SIA and Contact I.D. formats identify the zone with the low battery condition. A zone low battery trouble is displayed
immediately. Transmission may be delayed (section [377]). These reporting codes are transmitted to the System Maintenance call direction group.
Installer Lead In and Lead Out
The Installer Lead In and Lead Out reporting codes are sent when the panel enters and exits Installer Programming respectively.
[348] Test Transmission Reporting Codes
Walk Test Begin/End
These reporting codes are sent when the walk test is initiated and terminated. These codes precede and terminate the alarm reporting
codes for the zones that are activated during the walk test period, if the alarms are to be transmitted (section [382] option [2]). The walk
test reporting codes are sent to the System Test Transmission call direction group.
Periodic Test Transmission
When the programmed interval and time of day have elapsed, this reporting code is transmitted. This reporting code is sent to the System Test Transmission call direction group.
System Test
When the [][6][Master Code][4] command is used to perform a manual system test, this reporting code is sent to test the communicator. This reporting code is sent to the System Test Transmission call direction group.
[350] Communications Format Options
This section requires four 2-digit entries (1 per phone number). See Appendix B: Communicator Format Options.
i
If phone numbers are programmed for use with the alternate communicator modules, the programmed format must be SIA or
Contact ID.
Auto Sync with Alternate Communicator Module
If the panel detects an alternate communicator module, it automatically writes the communications format programmed in this section
(03 contact ID or 04 SIA) to programming section [022] of the alternate communicator module. If a communications format has not
been programmed for phone numbers 1-4, 04 (SIA) is written to the alternate communicator module by default. If both SIA and Contact
ID are programmed, Contact ID is written to the alternate communicator module. Synchronization takes place when Installer Programming is exited or DLS disconnects.
[351]-[376] Communicator Call Direction Options
Communicator call directions can be configured for 4 different phone numbers. Each reporting code falls under one of the following 5
groups:
•
Alarms & Restores
•
Openings & Closings
•
Tampers & Restores (including System Tampers)
•
System Maintenance Alarms & Restores
•
System Test Transmissions
52
WWW.DIYALARMFORUM.COM
5.4 Programming Descriptions
Each group can be assigned to the following call directions:
Option 1:
1st Telephone Number
Option 2:
2nd Telephone Number
Option 3:
3rd Telephone Number
Option 4:
4th Telephone Number
[377] Communicator Variables
Program a 3-digit number for each program entry:
Swinger Shutdown (Alarms): Maximum number of alarm/restore transmissions per zone. Valid entries: [000] to [014]. Program data
[000] to disable shutdown.
Swinger Shutdown (Tamper): Maximum number of tamper alarm/restore transmissions per zone. Valid entries: [000] to [014]. Program data [000] to disable shutdown.
Swinger Shutdown (Maintenance): Maximum number of trouble alarm/restore transmissions per trouble condition. Valid entries:
[000] to [014]. Program data [000] to disable shutdown.
Communicator (Transmission) Delay: Time, in seconds, panel delays reporting an alarm event. Valid entries: [000] to [255].
AC Failure Communication Delay: Time in minutes or hours, panel delays reporting an AC trouble event or restore.
Note: AC Restore communications follow the same delay.
TLM Trouble Delay: Time, in 3 second checks, before the system considers the phone line disconnected. Valid entries: [003] to
[255]
(e.g., 3 x 3 seconds = 9 seconds).
Note: TLM Restore follows the same delay.
Test Transmission Cycle (Land Line): Number of days or hours between test transmission reporting events. Valid entries: [001] to
[255]. [000] disables the Test Transmission.
Wireless Device Low Battery Delay: Number of days the system delays reporting a wireless low battery to the central station.
Valid entries: [000] to [255]. Program data [000] for no delay.
Delinquency Transmission Delay: Number of hours (Activity Delinquency) or days (Arming Delinquency) the panel delays before
transmitting the event to the central station. Valid entries: [001] to [255].
Communication Cancelled Window (CP-01 only): Time, in minutes, after an alarm has occurred that the system reports a Communication Cancel reporting event if the system is disarmed. The keypad displays “Communication Cancelled” to indicate that the communication cancelled reporting event has been successfully sent to the monitoring station. Valid entries: [005] to [255].
[378] Test Transmission Time of Day
Program the time the system will report a Test Transmission reporting event. Program 4 digits – [HHMM] using military standard.
For a test transmission at 11:00 pm, program data [2300]. Valid entries are [0000] to [2359], [9999] to disable.
[380] First Communicator Options
Option Description
[1]
ON: Communications Enabled. The system communicator is enabled.
OFF: Communications Disabled. The communicator is disabled.
[2]
ON: Restores on Siren Time-out. The system transmits alarm Restores if the zone is restored and the bell has timed out.
OFF: Restores Follow Zones. The system transmits alarm restores immediately when the zone is restored.
[3]
ON: Pulse Dialing. The panel uses rotary (pulse) dialing.
OFF: DTMF Dialing. The panel uses touchtone (DTMF) dialing.
[4]-[5] Future Use
[6]
ON: Alternating Backup Dialing Enabled. The communicator switches to the next backup number in the sequence after
each failed dialing attempt. This continues until communications are successful or the sequence has been repeated 5 times.
OFF: Call Primary Number, Backup to secondary. If 5 attempts to communicate to the primary telephone number fail, the
communicator switches to the next backup and makes up to 5 more attempts. If communications failure continues the communicator will attempt the second and third backup numbers if designated.
[7]
Future Use
[8]
ON: Delinquency Follows Zone Activity (Hours). The Delinquency feature follows zone activity.
OFF: Delinquency Follows Arming (Days). The Delinquency feature follows arming.
WWW.DIYALARMFORUM.COM
53
SCW9055/57 Wireless Alarm System
[381] Second Communicator Options
Option
Description
[1]
ON: Opening After Alarm Keypad Ringback Enabled. When the Opening After Alarm reporting code is successfully
transmitted to a programmed telephone number, the keypad sounds a series of 8 beeps to confirm to the end user that the
Opening After Alarm Code was sent and received. This Ringback occurs for each Opening After Alarm code successfully
reported.
OFF: Opening After Alarm Ringback Disabled.
[2]
Future Use
[3]
ON: SIA Uses Programmed Reporting Codes. The system uses programmed reporting codes when transmitting using the
SIA format.
OFF: SIA Uses Automatic Reporting Codes. The system automatically generates all reporting codes transmitted.
[4]
ON: Closing Confirmation Enabled. The system beeps the keypad 8 times after successfully transmitting a Closing reporting event.
OFF: Closing Confirmation Disabled. The keypad does not beep.
[5]-[6] Future Use
[7]
ON: Contact ID Uses Programmed Reporting Codes. The system uses Contact ID format programmed reporting codes
when transmitting reporting codes.
OFF: Contact ID Uses Automatic Reporting Codes. The system automatically generates all reporting codes transmitted.
[8]
Future Use
[382] Third Communicator Options
Option Description
54
[1]
Future Use
[2]
ON: Alarm Communications Enabled During Walk Test. The system transmits all alarms during Walk Test.
OFF: Alarm Communications Disabled During Walk Test. The system does not report alarm events during Walk Test.
[3]
ON: Communications Cancelled Message Enabled. The keypad displays the message “Communications Cancelled” upon
successful transmission of the Communication Cancelled reporting event.
OFF: Communications Cancelled Message Disabled. The keypad does not display these messages. (ON for SIA CP-01).
[4]
ON: Call Waiting Cancel Enabled. The system dials the Call Waiting Cancel string on the first attempt to dial the central
station.
OFF: Call Waiting Cancel Disabled. The system does not dial the Call Waiting Cancel string.
[5]
ON: Alternate Communicator Module Enabled. This option enables supervision of the Cellular/Etherner communicator.
This option must be ON to allow communications through the Cellular/Etherner communicator.
Note: When this option is OFF, Installer Programming sections [850]-[851] are not accessible.
OFF: Alternate Communicator Module Disabled. The panel will not attempt to supervise the Cellular/Etherner communicator. When this option is OFF the Cellular/Etherner communicator is disabled.
[6]
ON: AC Failure Transmission Delay in Hours. The System AC Failure Communication Delay in section [377] is programmed in hours.
OFF: AC Failure Transmission Delay in Minutes. The System AC Failure Communication Delay in section [377] is programmed in minutes.
[7]
ON: Number of Dialing Attempts is 1 for Residential Dial. Number of Dialing Attempts is one when using Residential
Dial communication format.
OFF: Residential Dialing Attempts is 5. Number of Dialing Attempts is five when using Residential Dial communication
format.
[8]
Future Use
WWW.DIYALARMFORUM.COM
5.4 Programming Descriptions
[383]
Option
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
Fourth Communicator Options Code
Description
Future Use
ON: Phone number 2 Backs Up Phone number 1. Phone number 2 backs-up phone number 1 if phone number 1 fails to
communicate (FTC). Phone number 2 communicates in the same format as phone number 1.
OFF: Phone number 2 is Independent. Phone number 2 does NOT back up phone number 1. Events are communicated to
phone number 2 (if enabled in Communicator Call Direction, section [351]-[376]), using the communicator format programmed in section [350].
ON: Phone number 3 Backs up number 2. Phone number 3 backs-up phone number 2 if phone number 2 fails to communicate (FTC). Phone number 3 communicates in the same format as phone number 2.
OFF: Phone number 3 is Independent. Phone number 3 does NOT back up phone number 2. Events are communicated to
phone number 3 (if enabled in Communicator Call Direction, section [351]-[376]), using the communicator format programmed in section [350].
ON: Phone number 4 Backs up number 3. Phone number 4 backs-up phone number 3 if phone number 3 fails to communicate (FTC). Phone number 4 communicates in the same format as phone number 3.
OFF: Phone number 4 is Independent. Phone number 4 does NOT back up phone number 3. Events are communicated to
phone number 4 (if enabled in Communicator Call Direction, section [351]-[376]), using the communicator format programmed in section [350].
ON: FTC’ed Events Communicate. The panel transmits Failure to Communicate (FTC) events if the digital communicator
is unsuccessful in communicating with any of the programmed telephone numbers. The FTC trouble/restore reporting code is
transmitted via the corresponding event call direction.
OFF: FTC’ed Events Do Not Communicate. FTC events are not transmitted. FTC trouble/restore reporting codes are
transmitted via the Maintenance call direction group after the next successful transmission.
ON: Account Code Error Check Enabled. Enabling this option ensures that a new account code is programmed. Upon
attempting to exit Installer Programming, the panel checks if a phone number is programmed in sections [301], [302], [303]
and [305]. If a phone number is programmed in any of these sections, the panel checks if the format is residential dial in section [350]. If the format is residential dial, the check process is aborted. If the format is anything but residential dial, the panel
checks that the system account code has been changed from the default (FFFFFF) or has been programmed with an invalid
entry (0000XX or FFFFXX).
If the account code has not been programmed when the installer attempts to exit Installer Programming:
• The system turns on the trouble LED and sounds an error tone for 5 seconds.
• The prompt “Account Code Not Programmed[]” is displayed on the keypad.
• When the 5-second error tone expires, the system automatically enters installer programming section [310] so the account
code can be programmed.
If the account code has been programmed, the panel operates normally.
OFF: Account Code Error Check Disabled. The account code is not checked when exiting Installer Programming.
Future Use
ON: Remote notification format is SIA. The panel sends SMS or other remote notifications to the communicator in SIA
format.
OFF: Remote notification format is CID. The panel sends SMS or other remote notifications to the communicator in Contact ID format.
[389] Alternate Communicator Fault Check Timer
The programmed number of poll commands that must be sent without valid poll responses before the panel generates a trouble condition. The number of valid checks happen at 3-second intervals. After the time-out an Ethernet or Cellular fault trouble is generated.
Valid entries are 003-255 for trouble annunciation and transmission. The trouble restore is delayed in the same manner as well.
[401] First Downloading Options
Option
Description
[1]
ON: Answering Machine/ Double Call Enabled. The system answers incoming calls for downloading (either Programmed
Number of Rings or Double Call).
OFF: Answering Machine/ Double Call Disabled. The system does not answer incoming calls for double call attempts, but
still answers on Programmed Number of Rings.
These settings do not affect the 6 hour DLS downloading window on power up.
[2]
ON: User Can Enable DLS Window. The user can enable downloading for the DLS downloading window (double call only)
using the [][6] command.
OFF: User Cannot Enable DLS Window. The user can not enable the DLS window using the [][6] command.
[3]
ON: Call Back Enabled. The system hangs up after a successful DLS connection and calls the computer back using the DLS
Phone Number (Section [402]).
OFF: Call Back Disabled. The system stays connected to the computer.
[4]
ON: User Initiated Call-up Enabled. The user can initiate a downloading session using the [][6] command.
OFF: User Initiated Call-up Disabled. The user cannot initiate a downloading session.
WWW.DIYALARMFORUM.COM
55
SCW9055/57 Wireless Alarm System
[5]
Future Use
[6]
ON: 300 Baud Panel Call-Up. When the user initiates a DLS connection, the panel connects and sends the initial header at
300 baud.
OFF: 110 Baud Panel Call-Up. When the user initiates a DLS connection, the panel connects and sends the initial header at
110 baud. The panel then switches to 300 baud in order to receive the response from the DLS computer.
[7]
Future Use
[8]
ON: Alternate Communicator DLS Always. When this feature is enabled, the SCW9055/57 responds to DLS requests
through the Alternate Communicator IP or Cellular paths at any time regardless of whether the DLS window is active or not.
Note: If an incorrect DLS Access Code is entered 5 times in a row when trying to establish a connection, the panel locks out
the alternate communicator DLS access until the next hour roll-over.
OFF: Alternate Communicator Follows DLS Window. When this feature is disabled, the SCW9055/57 only responds to
DLS requests through the alternate communicator IP or Cellular paths when the DLS window is active. The DLS window is
active following a power up of the control panel, or when the user enables it by pressing [5] while in the [*][6] User Functions
menu.
[402] DLS Downloading Computer’s Telephone Number
The Downloading Computer Telephone Number is used for Call Back and User Initiated DLS functions. Program the phone number as
required. HEX digits can be included for special applications:
HEX [A]
Not used
HEX [B]
Simulates a [] key press
HEX [C]
Simulates a [#] key press
HEX [D]
Additional dial tone search
HEX [E]
2-second pause
HEX [F]
End of phone number marker
[403] DLS Downloading Access Code
Program the 6-digit Downloading Access Code. Upon connection, the system only connects to the downloading computer if the
Downloading Access Code programmed matches the Downloading Access Code programmed in the computer file.
Note: The DLS Downloading Access Code must be changed from it's default value.
[404] Panel ID Code
Program the 6-digit Panel Identification Code. This code is used by the downloading computer to verify the correct account is calling
back (Call Back feature) or to identify which customer account file should be used (User Initiated DLS features).
[405] Double Call Timer
Program the maximum time in seconds, between calls, when connecting to the panel using the Double Call feature.
[406] Number of Rings to Answer On
The value in this section determines how many rings the panel will automatically pick up on in order to establish a DLS connection.
i
If Section [401] Option 1 and Section [406] are both enabled, either one works depending on how the installer calls the premises.
[501]-[502] PGM Output Attributes
Allows the installer to customize PGM1 and PGM2 Attributes. The following attributes can be enabled or disabled for each PGM output. When a PGM option is changed, the corresponding PGM’s attributes are defaulted.
Option Description
The following attributes are available for PGM Output Types [01], [05]-[08] and [17]-[18]
[1]-[2] Future Use
[3]
Output Level
ON: Output activates (switch to Ground) when the event occurs.
OFF: Output de-activates (switch to open) when the event occurs.
[4]
Output Options
ON: Output Pulsed. When using [][7], the output activates for the duration programmed in the PGM output timer, section [170].
OFF: Output On/Off. The output toggles between on and off when the corresponding [][7] command is entered.
The following attribute is available only for PGM Output Types [11] and [19]-[20].
[5]
Access Code Options
On: Access code required for activation.
Off: No access code required for activation.
56
WWW.DIYALARMFORUM.COM
5.4 Programming Descriptions
The following attributes are available for the System Trouble PGM option [09]
System Trouble PGM (Type 09)
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
Service Required
A.C. Failure
Telephone Line Fault
Communications (Failure to Communicate)
Device (Fire) Fault / WLS Zone Supervisory Fault Enabled
Device Tamper
Device Low Battery
Loss of Clock
The following attributes are available for the System Event PGM option [10]
System Event PGM (Type 10)
[1] Burglary
Delay, Instant, Interior, Stay/Away, Night, and 24 Hour Burglary Zone Types
[2] Fire
Key, Fire zone
[3] Panic
Key and Panic zones
[4] Medical
Key, Medical, and Emergency zones
[5] Supervisory
Supervisory, Auxiliary, Freeze, and Water zones
[6] Priority
Gas, CO, 24-Hour Heat and 24-Hour non-Latching Tamper zones
[7] Duress
Duress alarms
[8] Output Options
ON: Output Follows PGM Timer (Attribute 8). The output activates for the duration programmed for the PGM output timer (section [170])
OFF = Output is Latched. The output is active until a valid access code is entered.
i
If a system event PGM is programmed to follow the command output timer (Attribute 8 On), all other PGM attributes must
be enabled.
[591]-[592] Inactivity Timers 1 & 2 Start and End Times
Inactivity timers are used to create two windows to monitor 24-Hour. non-alarm zone activity. They are [591] Inactivity Timer 1 Start,
Inactivity Timer 1 End, [592] Inactivity Timer 2 Start, and Inactivity Timer 2 End. Enter two 4-digit decimal numbers in these two sections. Valid entries for each 4-digit decimal entry are 0000 to 2359. Enter 9999 to disable. The Failed to Arm reporting code follows the
alarms and restores call directions.
[600] 2-way Audio Control Options 1 (applies to SCW9057 only)
Option Description
[1]
ON: Tampers Enabled. The Talk/Listen-in session initiates for tamper conditions.
OFF: Tampers Disabled. 2-way Audio is disabled for tamper conditions.
[2]
ON: Openings and Closings Enabled. The Talk/Listen-in session initiates for Openings & Closings events.
OFF: Openings and Closings Disabled. 2-way Audio is disable for Openings & Closings events.
[3]
ON: [A] Key Alarm Enabled. The Talk/Listen-in session initiates for [A] Key Alarm.
OFF: [A] Key Alarm Disabled. 2-way Audio is disabled for [A] Key Alarm.
[4]
ON: [P] Key Alarm Enabled. The Listen-in session initiates for [P] Key Alarm if the [P] Key is programmed to be Silent. If
the [P] Key is programmed to be audible, the 2-way audio session will be Talk/Listen-in.
OFF: [P] Key Alarm Disabled. 2-Way Audio is disabled for [P] Key Alarm.
[5]
ON: Duress Alarm Enabled (Listen). The Listen-in session initiates for Duress Alarm.
OFF: Duress Alarm Disabled. 2-Way Audio is disabled for Duress Alarm.
[6]
ON: Opening after Alarm Enabled. The Talk/Listen-in session initiates for Opening After Alarm.
OFF: Opening after Alarm Disabled. 2-Way Audio is disabled for Opening After Alarm.
[7]
ON: Siren Active during 2-way Audio Verification. The sounder will remain active during a 2-way Audio session when an
audible alarm is present
OFF: Siren Silent during 2-way Audio Verification. The sounder will be silent when a 2-Way Audio session begins when
an audible alarm is present, allowing the user to hear the operator. The sounder will resume operation for the timeout duration
if the panel has not been disarmed at the end of the 2-way session.
i
[8]
This option must be ON for UL Listed Installations.
ON: Two-Way Audio is Initiated by the CS Operator: The alarm sounds but the 2-way audio session does not begin until
the central station operator activates it. The siren turns off once the 2-way audio session has begun.
OFF: Two-Way Audio Session is Immediate: The siren turns off and the 2-way audio session begins immediately after
sending the event.
WWW.DIYALARMFORUM.COM
57
SCW9055/57 Wireless Alarm System
[601] 2-way Audio Control Options 2 (applies to SCW9057 only)
Option Description
[1]
ON: Talk/Listen on Phone #1 Enabled. If Talk/Listen is required for an event, the panel initiates a Talk/Listen session with
the central station on phone #1.
OFF: Talk/Listen on Phone #1 Disabled. The panel does not request a Talk/Listen session on Phone #1.
[2]
ON: Talk/Listen on Phone #2 Enabled. If Talk/Listen is required for an event, the panel initiates a Talk/Listen session with
the central station on phone #2.
OFF: Talk/Listen on Phone #2 Disabled. The panel does not request a Talk/Listen session on Phone #2.
i
When using redundant communications with phone line and Cellular, if 2-way audio is enabled, a 2-way voice session is
established over both paths at the same time.
[3]
ON: Talk/Listen on Phone #3 Enabled. If Talk/Listen is required for an event, the panel initiates a Talk/Listen session with
the central station on phone #3.
OFF: Talk/Listen on Phone #3 Disabled. The panel does not request a Talk/Listen session on Phone #3.
[4]
ON: Talk/Listen on Phone #4 Enabled. If Talk/Listen is required for an event, the panel initiates a Talk/Listen session with
the central station on phone #4.
OFF: Talk/Listen on Phone #4 Disabled. The panel does not request a Talk/Listen session on Phone #4.
[5]-[8] Future Use
[609] Module Tamper Reporting Codes
This section is used for programming keypad and siren tamper reporting codes. A value of 00 can be entered to disable individual
reporting codes.
[610] Alternate Communicator Receiver Trouble Reporting Codes
This section is used for programming alternate communicator receiver trouble reporting codes. A value of 00 can be entered to disable
individual reporting codes.
[611] Repeater Tamper Reporting Codes
This section is used for programming WS4920/8920 tamper reporting and AC loss codes. A value of 00 can be entered to disable individual reporting codes.
[700] Automatic Clock Adjust
The value entered here adds or subtracts seconds at the end of each day to compensate for inaccuracies in the system time. Valid entries
are 00-99, with 60 seconds being the default. Monitor the time lost by the panel over a period of time to determine the average value
required for this section.
Example: Panel loses an average of 9 seconds a day. Instead of loading 60 seconds for the last minute of each day, program the panel to
load 51 seconds with the use of section [700]. This will speed up the panel by 9 seconds every day, thereby fixing the problem.
[701] First International Options
Option
Description
[1]
ON: 50 Hz AC. Configures the system for 50Hz AC.
OFF: 60 Hz AC. Configures the system for 60Hz AC.
[2]
ON: Time Base - Internal Crystal. The system uses the internal crystal for the internal panel clock.
OFF: Time Base - AC Line. The system uses the AC frequency for the internal panel clock.
[3]
ON: AC/DC Arming Inhibit Enabled. The system inhibits arming if a Low Battery or AC trouble condition is present.
OFF: AC/DC Arming Inhibit Disabled. Arming is not inhibited.
[4]
ON: All System Tampers Require Installer Reset. All Tamper troubles latch and arming is inhibited. Enter Installer Programming to clear the trouble condition and return to normal operation.
OFF: All System Tampers Follow Restore. Tamper troubles do not latch and do not inhibit arming. Manual bypassing of
a zone does not bypass the tamper or fault states (DEOL).
[5]
ON: 6-digit User Access Codes. All access codes are 6 digits long.
OFF: 4-digit User Access Codes. All access codes are 4 digits long.
[6]
ON: Busy Tone Detection Enabled. The system hangs up if a busy tone is detected.
OFF: Busy Tone Detection Disabled. The system does not detect busy tones.
[7]-[8] Future Use
58
WWW.DIYALARMFORUM.COM
5.4 Programming Descriptions
[702] Second International Options
Option
Description
[1]
ON: Pulse Dialing Make/Break ratio is 33/67. The communicator uses 33/67 make/break ratio when pulse dialing.
OFF: Pulse Dialing Make/Break ratio is 40/60. The system uses 40/60 make/break ratio.
[2]
ON: Force Dialing Enabled. The system dials regardless of the presence of dial tone after the first attempt.
OFF: Force Dialing Disabled. The system dials only if dial tone is detected.
[3]
Future Use
[4]
ON: 1600Hz Handshake. 1600Hz handshake used.
OFF: Standard Handshake. Standard handshake is used.
[5]
ON: ID Tone Enabled. The system generates a tone every 2 seconds indicating digital equipment is making the call rather
than a voice call.
OFF: ID Tone Disabled. The system does not generate a tone.
[6]
ON: 2100 Hz. ID Tone. The tone generated (2100Hz.) indicates that digital equipment is making the call.
OFF: 1300 Hz. ID Tone. The tone is 1300Hz.
[7]-[8] Future Use
[703] Delay Between Dialing Attempts
Program the time the system waits between dialing attempts to transmit a reporting event to the central station. Valid entries are [001] to
[255].
[800] Door Chime Options for Zones 1-34
Keypads and indoor sirens can annunciate one of four different door chime tones for each zone on the system.
Each section contains the following chime options:
•
Enable one door chime option for each zone.
•
If more than one option is enabled, the highest numerical option enabled takes precedence.
For example: If options 3 and 1 are both enabled, then the zone sounds option 3 - “Ding-Dong.”
•
If all door chime options are disabled, the keypad/siren does not sound a door chime tone for that particular zone.
Option
Description
[1]
ON: Standard Door Chime Enabled. Traditional door chime tone found on other DSC keypads (6 quick beeps).
OFF: Standard Door Chime Disabled.
[2]
ON: “Bing-Bong” Door Chime Enabled.
OFF: “Bing-Bong” Door Chime Disabled.
[3]
ON: “Ding-Dong” Door Chime Enabled.
OFF: “Ding-Dong” Chime Disabled.
[4]
ON: 4-second Alarm Tone Door Chime Enabled. The keypad/siren sounds a medium volume alarm signal for 4 seconds.
OFF: 4-second Alarm Tone Door Chime Disabled.
[5]-[8]
Future Use
[804]-[001]-[032] Wireless Device Serial Number
These sections are for manual enrollment of wireless device electronic serial numbers (ESN).
• See [804][101]-[116] for one-way and two-way wireless key enrollment.
• See [804][201]-[204] for two-way keypad enrollment.
• See [804][301]-[304] for two-way siren enrollment.
This is a 6-digit (one-way) or 8-digit (2-way) entry. For toggling entries between decimal and hexadecimal values, press [].
One-way Devices
The first digit of a 6-digit serial number for one-way devices identifies the type of device as indicated below:
2
Door/Window Contact, Flood Sensor or Wireless Repeater
3
PIR or Glass Break Detector
4
Smoke Detector
5
Panic Pendant
8
Carbon Monoxide Detector
i
Leading 00s must be entered for one-way wireless devices with six-digit serial numbers (E.g.,
SN 234567 must be entered as 00234567).
WWW.DIYALARMFORUM.COM
59
SCW9055/57 Wireless Alarm System
[804][081] Wireless Supervisory Window
This entry is used to program the length of time a wireless device must be absent from the system before a fault is generated. The wireless supervisory window is calculated by multiplying the programmed value by 15 minutes.
Valid entries are 04 to 96 which correlates to 1 to 24 hours. The default value for North America is 96 (24 hours) and 08 (2 hours) for
Europe.
i
This timer may run the programmed time plus up to the number of minutes programmed in this section. For example, the
European default is 2 hours, but the actual time could be as long as 2 hours and 8 minutes. The North American default is
24 hours, but the actual time could be as long as 25 hours and 36 minutes.
Note: UL fire listings require a 4 Hr setting (4 Hrs = 16, 16x15 minutes).
[804][082]-[085] Zone Transmitter Supervision Options
Program these sections if the zone transmitter will be supervised. All zones are enabled for supervision by default.
i
DSC does NOT recommend supervision of panic pendants, because they may be removed from the premises.
[804][101]-[116] Wireless Key Serial Number
These sections are used to enter the wireless key serial numbers. Each 2-way serial number is an 8-digit hexadecimal entry. To toggle
entries between decimal and hexadecimal values, press []. One-way serial numbers are 6-digits. “00” must be added to the start of a 6digit serial number.
[804][141]-[156] Wireless Key Function Key Options
Up to 6 unique functions can be programmed for each wireless key. Each section requires four 2-digit entries. The following table
describes each programmable function.
Entry
00
03
04
05
06
13
14
16
17
25
27
29
30
33
Description
Null Key (Key Not Used)
Stay Arm
Away Arm
[][9] No-Entry Arm
[][4] Chime On / Off
Command Output 1 [][7][1]
Command Output 2 [][7][2]
[][0] Quick Exit
[][1] Reactivate Stay/Away Zones
Instant Stay Arm
Disarm (Off)
Auxiliary Alarm
Panic Alarm
Night Arm
DSC Wireless Key
YES
YES
YES
[][9] No-Entry Arm can be used if the wireless key being used is identified.
YES
[][7][1] commands can be used with an access code if the wireless keys are identified.
[][7][2] commands can be used with an access code if the wireless keys are identified.
YES
YES
YES
Disarming can be used with an access code, as long as the wireless keys are identified.
YES
YES
YES
[804][181]-[182] Wireless Key Enable/Disable
These sections enable each individual key enrolled on the system. The keys are all enabled on the system by default.
[804][201] Wireless Keypad Serial Number
These sections are used to enter the wireless keypad serial numbers. The number is an 8-digit hexadecimal entry. To toggle between
decimal and hexadecimal value entries, press [].
[804][202] IT-410 Serial Number
This section is used to enter the two way wireless integration module IT-410 serial number. This is an 8 digit hexadecimal entry. To
toggle between decimal and hexadecimal value entries, press [].
[804][301]-[302] Wireless Siren Serial Number
These sections are used to enter the wireless siren serial numbers. The number is an 8-digit hexadecimal entry. To toggle between decimal and hexadecimal value entries, press [].
[804][311]-[314] Wireless Siren Options for Sirens 1-2
Each section contains the following 8 options:
Option Description
60
[1]
ON: Siren Enabled. The WT49X1 activates at full volume for fire, burglary, and CO alarm conditions. This option also
enables walk test and system test indications for WT49X1 modules, and placement test, walk test, and system test indications
for WT4911 modules.
OFF: Siren Disabled. The WT49X1 does not activate for fire, burglary, CO Alarm, walk test or system test indications.
Placement test is still sounded by WT4901 modules.
[2]
ON: Buzzer Notifications Enabled. The siren activates audible signals for entry/exit delays, and 24 hour buzzer zone
alarms. This may be desirable for indoor sirens, but not outdoor sirens.
OFF: Buzzer Notifications Disabled. Audible signals are not sent.
WWW.DIYALARMFORUM.COM
5.4 Programming Descriptions
[3]
ON: Door Chime Enabled. The siren activates for door chime conditions.
OFF: Door Chime Disabled. The siren does not activate for door chime conditions.
[4]
ON: Trouble Beeps Enabled. The siren activates for trouble beep conditions. Trouble beeps are sounded until any key on the
keypad is pressed or until all trouble conditions are restored. This is intended for indoor sirens, but not outdoor sirens or sirens
that are mounted in a sleeping area.
Off: Trouble Beeps Disabled. The siren does not activate for trouble beeps.
[5]
ON: Bell Squawks Enabled. The siren activates programmed bell squawk conditions (e.g., arming, disarming, disarming
with alarms in memory). This may be desirable for outdoor sirens, but not indoor sirens. These squawks are sounded at full
alarm volume.
OFF: Bell Squawks Disabled. The siren does not activate for bell squawk conditions.
[6]
ON: Strobe Enabled (WT4911 only). The strobe activates for alarms, placement test, walk test, system test and arm/disarm
squawk indications. The strobe can be used to identify a system alarm before entering the premises.
OFF: Strobe Disabled. The strobe does not activate.
[7]
ON: Buzzer Alarm / Strobe Follows Bell Time Out. Indoor Siren - If the indoor siren is set for buzzer notifications (option 2),
buzzer alarms, such as 24 Hr buzzer zone types are shut off after they have been active for the duration of BTO. Outdoor siren: If
the strobe is enabled on the outdoor siren (option 6), the strobe shuts off once the siren is shut off at the end of the bell duration.
OFF: Buzzer Alarms / Strobe Follows Alarm Condition. Indoor siren - The siren sounds the buzzer alarm until the alarm
condition has been acknowledged (silenced) at the keypad. Outdoor siren: The strobe continues until an access code has been
entered at a system keypad, or a successful disarming request has been serviced.
[8]
ON: Siren Tamper Enabled. Tamper conditions from the siren generate a tamper trouble. The panel logs and communicates
the event.
OFF: Siren Tamper Disabled. Tamper conditions from the siren do not generate a tamper trouble. The panel logs and communicates the event. If a siren tamper condition is present in [ ✱ ][2], turning off this option clears the trouble from the system.
i
This option must be Off for CP-01 compliance.
[804][320] Global Siren Options
When these options are enabled or disabled, they affect all wireless devices on the system.
Option
Description
[1]
ON: Tamper Activates Siren / Strobe While Disarmed . When the system is in a disarmed state, a tamper condition from any enrolled
siren causes the system sirens and strobes to activate.
OFF: Tamper Does not Activate Siren / Strobe While Disarmed. When the system is in a disarmed state, a tamper condition from any
enrolled siren will not cause the system sirens and strobes to activate.
[2]
ON: Pre-Alarm Signal Enabled. When the system begins entry delay the entry delay time is sent to the wireless siren. If the wireless siren
does not receive a disarm command during the entry delay time, the siren will go into alarm.
OFF: Pre-Alarm Signal Disabled. When the system begins entry delay no entry delay time is sent to the wireless siren. The siren will not
go into alarm until it receives a signal from the panel to tell it to go into alarm.
[3]-[8] Future Use
[804][330] Maximum Outdoor Siren Activation Timer
This value determines the maximum time the wireless siren sounds before automatically turning off.
[804][401]-[404] Wireless Repeater Programming
These sections are used to enroll up to four WS4920 repeaters. During quick enroll, select slot 00 to enroll the device as a repeater. The
next available section ([401]-[404]) is displayed. Repeaters are placement tested using section [907].
Note: For Repeater supervision, ensure that dip switch 3 on the repeater is in the OFF state.
[804][900] General Wireless Options
When these options are enabled or disabled, they affect all wireless devices on the system.
Option
[1]
Description
ON: Repeater Harsh Placement Test Enabled. When interference is present between the Repeater and the SCW9055/57,
this functionality allows the installer to place the Repeater closer to the receiver to establish a stronger communication path.
This option does not affect or change the location characteristics of any other devices. This option is automatically disabled
when exiting Installer Programming.
Note: Only use this option when interference is detected using the Repeater placement test (Yellow LED on Repeater is ON)
or the Receiver Placement Test (section [907] on the SCW9055/57).
OFF: Repeater Harsh Placement Test Disabled.
[2]-[6] Future Use
[7]
ON: RF Jam Disabled. RF Jam conditions are NOT detected, displayed and communicated.
OFF: RF Jam Enabled. RF Jam conditions are detected, displayed and communicated.
[8]
Future Use
WWW.DIYALARMFORUM.COM
61
SCW9055/57 Wireless Alarm System
[850] Cellular Signal Strength
This section displays Cellular network signal strength on the LCD (“Cellular” is displayed on the first line). Scroll to the second line to
view. If the SIM card is activated, the second line displays and the signal strength bars. If the SIM card is not activated,
played beside the signal bars. Maximum signal strength is 5 bars.
is dis-
[851] Alternate Communicator Module Programming
Refer to the Communicator installation manual for programming details.
[898] Wireless Device Enrollment - See Section 2 of this manual.
[899] Template Programming - See Section 3 of this manual.
[900] Panel Version
The system displays the version of the control panel (for example, [0100] indicates panel version 1.00).
[904] Wireless Device Placement Test
See Chapter 2 for details.
[905] Wireless Keypad Placement Test
See Chapter 2 for details.
[906] Wireless Siren Placement Test
See Chapter 2 for details.
[907] Wireless Repeater Placement Test
See Chapter 2 for details.
[908] Wireless Modules
This section displays all wireless modules enrolled on the alarm system. View enrolled module names and slot numbers using the scroll
keys. e.g., an indoor siren enrolled on slot one is displayed as 'WT49X1 1'.
[990] Installer Lockout Enable
Enter Section [990][Installer Code][990] to enable this feature. A hardware default cannot be performed when the Installer Lockout
feature is ON. If the panel is powered up, the system chatters the line seizure relay 10 times to indicate the feature is ON.
[991] Installer Lockout Disable
Enter Section [991][Installer Code][991] to turn the Installer Lockout feature OFF.
[992] Alternate Communicator Module Label Broadcast
This section allows the installer to broadcast the partition and zone labels stored in the panel to the Alternate Communicator module
SMS label programming sections. Press * to broadcast the labels or # to exit the section. An error tone is sounded if the alternate communicator module is disabled (section [382] option 5) or is not present. Note: Label broadcast must be initiated by the SCW9055/57
main unit.
[996] Restore Wireless Device Programming Factory Defaults
Enter Section [996][Installer Code][996] to return wireless programming to factory defaults.
[998] Restore Panel Default Programming
Enter Section [998][Installer Code][998] to return control panel programming (including 2-way Audio options) to factory defaults.
Wireless device programming and keypad programming are not defaulted.
i To default Labels, see Section [996] Label Reset in Keypad Programming.
To default Wireless Devices, see Section [996] above.
[999] Restore Factory Default Programming
Enter Section [999][Installer Code][999] to return system programming to factory defaults.
Except for labels, all programming including wireless device programming and keypad programming is returned to factory
i defaults. To default labels, see Section [996] Label Reset in Keypad Programming.
Hardware Reset (Default) Main Control Panel
Perform the following to default the main control panel:
1. Power down the system completely.
2. Connect a short between I/O 1 and I/O 2 on the control panel (remove all other wires from these terminals).
3. Power up the control panel (AC power only) for 10 full seconds.
4. Power down the control panel, remove short between I/O 1 and I/O 2.
5. Power up the control panel.
Local Keypad Programming
To access Keypad Programming, enter [][8][Installer’s Code][].
To return to System Programming, press [].
62
WWW.DIYALARMFORUM.COM
5.4 Programming Descriptions
[000] Keypad Function Key Programming
This section is used to program the keypad function keys. To access enter [][000] from Installer Programming. Enter digits 1 to 5 to
select a function key (F1-F5) for programming. Key in a 2-digit entry to assign a function to the key. The system returns to the key
selection screen (in section [000]). Changes to this programming section affect only the keypad used to program the changes.
Function Key Options
i
Function keys must be held for 2 seconds to perform the described function.
Function keys only perform the intended function if the system is not busy.
Pressing function keys programmed with option numbers designated “Future Use” causes the keypad to display “Function Not
Available” and sound an error tone.
00
Null Key: (Not Used) The key does not perform any function or give any acknowledgement beeps when pressed.
01-02 Future Use
03
Stay Arm: The system arms with all Stay/Away and Night zones auto-bypassed even if delay zones are violated during the
exit delay. This key only works while the system is disarmed, or armed in the Away mode. The panel logs “Armed in Stay
Mode” for this closing type. If there are no Stay/Away zone types programmed on the system, the system arms in Away mode,
and the panel logs “Armed in Away Mode.”
04
Away Arm: The system arms with all Stay/Away and Night zones active even if no delay zones are violated during the exit
delay. This key only works while the system is disarmed, armed in the Stay or Night Mode, or during the Exit Delay. The
panel logs “Armed in Away Mode” for this closing type.
05
No-Entry Arm [][9]: After pressing this key, enter a valid access code. The system arms with No Entry on Delay zones and
all Stay/Away and Night zones are auto-bypassed even if delay zones are violated during the exit delay. The exit delay is silent
for this arming type. This key can be used in the armed or disarmed state to allow the user to turn Entry Delay on and off.
Entry of a valid access code is required after pressing this key to perform the function when the system is disarmed.
06
Chime ON/OFF [][4]: This key enables (3 beeps) and disables (steady tone) the chime. It functions similarly to entering
[][4]. This key functions when the system is armed or disarmed.
07
Future Use
08
Bypass Mode [][1]: Pressing this key puts the keypad into Zone Bypass mode. It is similar to entering [][1] while disarmed. If an access code is required for bypassing (Section [015] Option [5]), the user must press the function key to enter
bypass mode then enter the access code before entry is permitted. This key only works while the system is disarmed.
09-12 Future Use
13
Command Output #1 [][7][1]: Pressing this key is the equivalent of entering [][7][1] to activate the associated PGM. An
access code may be required before the output is activated, depending on attribute 5 of the output. This key works whether the
system is armed or disarmed.
14
Command Output #2 [][7][2]: Pressing this key is the equivalent of entering [][7][2] to activate the associated PGM. An
access code may be required before the output is activated, depending on attribute 5 of the output. This key works whether the
system is armed or disarmed.
15
Future Use
16
Quick Exit [][0]: Pressing this key performs the Quick Exit function and is the same as entering [][0] while armed. This
key only works while the system is armed. The Quick Exit feature must be enabled (section [015] Option [3]).
17
Reactivate Stay/Away Zones [][1]: Pressing this key removes (or re-enables) the automatic bypass on all Stay/Away zones
on the system. It is the same as entering [][1] while armed. If Night zones are programmed, the system arms in night mode if
this key is pressed while stay armed. If no Night zones are programmed, the system arms in Away mode. The panel logs the
appropriate arming log to the event buffer. If armed in Night or Away mode, this key switches the system back to Stay mode.
Pressing this key does not switch the system from Night to Away. This key only works when the system is armed.
18-24 Future Use
25
Instant Stay Arm: This feature operates similarly to the Stay arming function key except for the following: When this function key is pressed for 2 seconds, no acknowledgement beeps are sounded, there is no exit delay, and the system arms immediately. The panel logs “Armed in Stay Mode” for this closing type. If no Stay/Away zone types are programmed on the system,
the system arms in Away mode with an audible exit delay (for the duration programmed in section [005]), and the panel logs
Armed in Away Mode.
Note: This function key should not be used on CP-01 panels.
26-32 Future Use
33
Night Arm: The system arms with Night zones auto-bypassed even if delay zones are violated during the exit delay. This key
only works while the system is disarmed or armed in the Stay Mode. The panel logs Armed in Night Mode for this closing
type. If no Night zone types are programmed on the system, the system arms in Away mode with an audible exit delay (for the
duration programmed in section [005]), and the panel logs Armed in Away Mode. The function key must be pressed for 2 seconds. No acknowledgement beeps are sounded and the exit delay is silent.
WWW.DIYALARMFORUM.COM
63
SCW9055/57 Wireless Alarm System
[001]-[034] Label Programming (Zone 1-34)
Zone and other labels in these sections can be customized.
Default labels are in English and do not change when an alternate language is selected.
Labels can be programmed locally or downloaded/uploaded using DLS and Connect 24 interactive software.
To program a zone label:
1.
2.
3.
4.
Press
Enter the section number of the label to be programmed.
[<]
[>]
[✽ ]
Scroll to the desired character’s location using the <> [#]
Keys.
[0]
[1]
Enter the number of the corresponding character
[2]
group until the desired character is displayed.
[3]
Example:
[4]
Press the “2” key 3 times to enter the letter “F.”
[5]
Press the “2” key 4 times to enter the number
[6]
“2.”
[7]
Press [ ✱ ] to access the label programming options. [8]
[9]
Press [ ✱ ] to select the option.
To Enter/Display
Display Left (Previous character position)
Display Right (Next character position)
[SELECT]
[ESCAPE]
[SPACE]
[A], [B], [C], [1]
[D], [E], [F], [2]
[G], [H], [I], [3]
[J], [K], [L], [4]
[M], [N], [O], [5]
[P], [Q], [R], [6]
[S], [T], [U], [7]
[V], [W], [X], [8]
[Y], [Z], [9], [0]
SAVE - Saves the new label. If save is not selected before leaving the label programming section, the changes are lost.
CHANGE CASE - This option toggles the letter entry between upper case letters (A, B, C) and lower case letters (a, b, c).
ASCII ENTRY - This option is for entering uncommon characters, or as a primary method for programming labels. 255
character entries are available, although some entries are duplicated. Use the [<] [>] keys to scroll through the characters or
enter a 3-digit number from 000-255. Press the [] key to enter a character in the label.
CLEAR TO END - This option clears the display from the character where the cursor is located to the end of the display.
CLEAR DISPLAY - This option sets all characters in a label to “space” or cleared.
[065] Fire Alarm Label
Enter a 28-character Fire Alarm label. Default value = “FIRE-ZONE”
[066] Fail to Arm Event Message
Enter a 32-character Fail to Arm Event Message. Default value = “SYSTEM HAS ------”, “FAILED-TO-ARM---”
[067] Alarm When Armed Event Message
Enter a 32-character Alarm when Armed Event Message. Default value = “ALARM-OCCURRED--”, “WHILE-ARMED---”
[074] First Keypad Options
Option
64
Description
[1]
ON: [F] Key Enabled. Pressing and holding the Fire key for 2 seconds sends a fire key alarm request to the panel. The keypad displays “Hold Keys Down for Fire Alarm.”
OFF: [F] Key Disabled. Pressing the Fire key does not send an alarm or change the keypad's display.
[2]
ON: [A] Key Enabled. When the [A] key is pressed and held, the keypad generates a [A]ux key alarm. The display prompts
the user to hold the key.
OFF: [A] Key Disabled. Prevents the keypad from requesting an [A]ux key alarm.
[3]
ON: [P] Key Enabled. When the [P] key is pressed and held, the keypad generates a [P]anic key alarm. The display prompts
the user to hold the key, depending on the setting of Option 8 (in this section).
OFF: [P] Key Disabled. Prevents the keypad from requesting a [P]anic key alarm.
[4]
ON: Quick Arm Prompt ON. When in the Disarmed Star menu, the Quick Arm prompt is displayed.
OFF: Quick Arm Prompt OFF. The Quick Arm prompt is disabled.
[5]
ON: Quick Exit Prompt ON. When in the Armed Star menu, the Quick Exit prompt is displayed.
OFF: Quick Exit Prompt OFF. The Quick Exit prompt is disabled.
[6]
ON: Bypass Options Prompt ON. In the [*1] Bypass menu, the Bypass Options prompt is displayed. This is a local function
prompt. When selected, the keypad displays the Bypass Options menu.
OFF: Bypass Options Prompt and menu OFF. Prompt and menu is disabled.
[7]
ON: User Initiated Call-Up Prompt ON. In the [*6] User Functions menu, the User Initiated Call-up prompt is Displayed.
When this prompt is selected, the keypad sends a [6] key.
OFF: User Initiated Call-Up Prompt OFF. The prompt is not displayed.
[8]
ON: Hold [P]anic Key Prompt ON. When holding the [P] key, the display prompts the user to hold the [P] key to generate
a Panic alarm. This is a local prompt.
OFF: Hold [P] Key Prompt OFF. When holding the [P] key, the user receives no feedback that the key has been pressed.
The display and backlighting does not change.
WWW.DIYALARMFORUM.COM
5.4 Programming Descriptions
[075] Second Keypad Options
Option
Description
[1]
ON: Local Clock Display Enabled: When the keypad is not being used, the keypad returns to displaying the Time and Date
until another key is pressed.
OFF: Local Clock Display Disabled. Time and date is not displayed on the keypad.
[2]
ON: Local Clock Displays 24 Hour Time. When this feature is enabled, the time is displayed in 24 hour military format.
OFF: Local Clock Displays AM/PM Time. When this feature is enabled, the time is displayed in 12 hour format (AM/PM).
This option does not affect the time programming menu, which is always in 24-hour time format.
[3]
ON: Auto Alarm Scroll Enabled. When the bell is active or when there is an alarm in memory while armed, the keypad
scrolls automatically and displays all alarms.
OFF: Auto Alarm Scroll Disabled. The keypad does not scroll automatically and display all alarms.
[4]
ON: Language Selection Accessible from Any Menu. Pressing and holding [<][ >] for 2 seconds displays the language
selection menu.
OFF: Language Selection Accessible from Installer Menu Only. Pressing and holding [<][ >] for 2 seconds generates an
error tone.
[5]
ON: Power LED Enabled. The LED functionality is defined by Option 6.
OFF: Power LED Disabled. Option 6 has no effect.
[6]
ON : Power LED Indicates AC Present. The LED is ON to indicate AC power is present. If AC is absent, the LED is OFF.
OFF: Power LED Indicates AC Absent. The LED is ON to indicate AC power is absent. If AC is present, the LED is OFF.
[7]
ON : Alarms are Displayed while Armed. If any alarms occur while armed, the keypad displays the alarms by identifying
the zones.
OFF: Alarms are Not Displayed while Armed. If any alarms occur while armed, the keypad does not show any indication
that an alarm occurred on the system. When the system is disarmed, the keypad still enters Alarm Memory to indicate which
zones went into alarm during the alarm period.
[8]
ON : Auto Scroll Open Zones Enabled. When a zone is open, the keypad scrolls automatically and display all open zones.
Open zones also override the local clock display.
OFF: Auto Scroll Open Zones Disabled. Open zones are not displayed.
[076] Third Keypad Options
Option
Description
[1]-[4] Future Use
[5]
ON : Late to Open Prompts Enabled. The “Late to Open” enable/disable prompts in [][6] user functions are available in
the menu.
OFF : Late to Open Prompts Disabled. The “Late to Open” enable/disable prompts are not available.
[6]-[8] Future Use
[077] Programmed LCD Message
Enter a 32-character message. If any characters other than blanks are programmed into this section, the keypad times out to this message instead of the Time and Date display. Any option or feature that overrides the clock display also override the LCD message. An
override by the system is not counted against the Message Duration programmed in Section [078]. This message can be programmed in
Installer Programming or using DLS.
[078] Programmed LCD Message Duration
This section is used to program the number of times an LCD message must be cleared from the LCD displays (by pressing any key)
before it is no longer displayed. When programmed on the system, the LCD keypad displays the message when not in use. Programming 000 in this section results in the message never clearing. This could be used as a greeting (residential) or a company message
(commercial). This overrides the settings of Clock Display options in Section [075].
Valid Entries are 001 to 255 seconds. 000 = Unlimited Duration.
[100] CO Detector Alarm Label
Use this section to program a custom label for the CO Detector zone. This label is displayed on the keypad during CO detector zone
alarms. The CO Detector Alarm label can be 14x2 characters in length. Default message is CO_Alarm_Evacuate_Area.
[101] System Label
Use this section to program a custom label for the system. This label is a used on various displays to refer to the alarm system. The
default label is “System.” The system label can be up to 14x2 characters in length.
[120]-[121] Command Output Labels
Use these sections to program custom command output labels. These labels are used by the system to display output use and output activation events in the event buffer. Command output labels can be 14x2 characters in length.
[996] Label Default
This section resets programmable labels to factory defaults. Entering this section and pressing [] returns all programmable system
labels to default conditions in the currently active language. Keypad configuration sections are not affected.
WWW.DIYALARMFORUM.COM
65
SCW9055/57 Wireless Alarm System
[997] Keypad Version
Entering this section displays the keypad version. The keypad version is displayed as a 4-digit decimal entry.
E.g., Entry is 1234 = Version 12.34. This is a read-only value.
[998] Initiate Global Label Broadcast
Programmed keypad labels are broadcast and installed on all system keypads from keypad 1.
Enter [][998] to broadcast the labels programmed in sections [][001]-[069] and [][100]-[125]. This function is also required for
broadcasting labels downloaded using DLS software.
Initiate this function from the SCW9055/57 main unit. Program all labels manually on the SCW9055/57 first and then
i broadcasted to WT5500 keypad.
[999] Reset All Keypad Programming to Factory Defaults
Resets all keypad programming to the factory defaults. This un-enrolls the keypad from the system.
66
WWW.DIYALARMFORUM.COM
6 Testing & Troubleshooting
6 Testing & Troubleshooting
Testing:
•
•
•
•
Power up system
Program options as required (see programming section)
Violate, then restore zones
Verify correct Reporting Codes are sent to the central station
Troubleshooting:
• Power up system
• Enter [][2] to view Troubles
• Perform actions indicated in the tables below
Trouble Summary:
Trouble [1] Service Required - Press [1] or  for more information:
Low Battery
General System Trouble
General System Tamper
Trouble [2] - AC Trouble
Trouble [3] - Telephone Line Trouble
Trouble [4] - Failure to Communicate
Trouble [5] - Zone Fault -Press [5] or  for more information
Trouble [6] - Zone Tamper - Press [6] or  for more information
Trouble [7] - Wireless Device Low Battery - Press [7] or  for more information
Trouble [8] - Loss of Time or Date - Press  to program date and time
Trouble
Cause
Troubleshooting
Trouble [0] Atlernate Communicator Trouble
Press [<][>] to determine specific trouble
Alternate Comm SIM Lock
• Refer to the Communicator installation manual for more
details.
Alternate Comm Cellular
Trouble
Alternate Comm Ethernet
Trouble
Alternate Comm Receiver
Trouble
Alternate Comm Supervision
Alternate Comm Config
SMS Trouble
Alternate Comm Fault
The SIM lock feature has been enabled
and the unit has not been programmed
with the correct PIN for the SIM card.
This condition is created when the alternate communicator has detected a radio
or SIM failure, a cellular network trouble, or insufficient signal strength.
This condition is created when the alternate communicator has detected a network absent condition.
This condition is generated when the
alternate communicator loses supervision
or fails to initialize a receiver.
This condition is created when the panel
loses communication with an Ethernet or
cellular receiver on the system.
This condition is created when the alternate communicator detects an SMS Connect 24 Configuration SMS failure
trouble.
This condition is created by the
SCW9055/57 when the alternate communicator has not responded to any poll
commands. Alternate Comm Fault is
displayed in [*][2] and the event buffer.
The reporting code for this trouble is
General System Supervisory.
• Refer to the Communicator installation manual for more
details.
• Refer to the Communicator installation manual for more
details.
• Refer to the Communicator installation manual for more
details.
• Refer to the Communicator installation manual for more
details.
• Refer to the Communicator installation manual for more
details.
• Refer to the Communicator installation manual for more
details.
WWW.DIYALARMFORUM.COM
67
SCW9055/57 Wireless Alarm System
Trouble [1] Service Required
Low Battery
General System Trouble
General System Tamper
RF Jam
Press [1] to determine specific trouble
The panel detects that no battery is pres- NOTE: If battery is new, allow 24 Hrs. to charge.
ent, that the battery is shorted, or that the • Verify voltage measured across AC terminals is 16-18
VAC.
battery is below the low battery threshold
• Verify voltage measured across battery terminals is 12.5V
(less than 7.2VDC).
+/- 0.1V.
NOTE: This trouble condition will clear • Replace transformer if required.
once the panel determines that the battery • Disconnect then reconnect battery leads.
can be charged properly, even if the low • If Low Battery Trouble LED is still on after 10 minutes,
replace battery.
battery restore threshold has not been
reached.
• Check event buffer to determine specific trouble.
Communications with the wireless
receiver have failed causing a Hardware • If buffer logs “Hardware Fault” or “LCD Loss” replace
fault, an Aux Supply Trouble is present
panel.
or the LCD display is not functioning.
• If necessary, test AC outlet for loss of power and remedy.
Cover tamper tripped.
• Verify that tamper button is installed into backplate.
• Verify that keypad (cover) is secured to backplate.
The system has detected the presence of • Check Event buffer to determine specific trouble.
an RF jam for 20 seconds or communica- • If Buffer logs RF Jam trouble, check for external
tions with the wireless receiver have
433MHZ signal sources. To disable RF Jam: enable
failed causing a Hardware fault. An RF
Option [7] in program section [804] subsection [90].
jam may also be detected by a wireless • If Buffer logs Hardware fault - replace panel.
repeater.
The Trouble light on the alarm panel
glows orange to indicate RF jam.
Trouble [2] AC Failure
AC Failure
No AC at panel AC input terminals,
enrolled WS4920/8920 repeater has
experienced loss of AC power.
• Verify voltage measured across AC terminals is 1618VAC. Replace transformer if required.
• If buffer logs “Repeater AC Loss”, inspect repeater for
cause (power supply unplugged from AC outlet, power
supply wires loose or disconnected.
Trouble [3] Telephone Line Trouble
Telephone Line Trouble
Phone line voltage at TIP, RING on main Measure the voltage across TIP and RING on the panel:
panel is less than 3VDC.
• No phone off-hook – 50VDC (approx.).
• Any phone off-hook – 5VDC (approx.).
Wire incoming line directly to TIP and RING.
• If trouble clears, check wiring or the RJ-31x phone jack.
Trouble [4] Failure to Communicate
Failure to Communicate
68
Panel fails to communicate one or more
events to central station.
Connect a headset to TIP and RING of the control panel.
Monitor for the following conditions:
Continuous dial tone
• Reverse TIP and RING.
Recorded operator message comes on
• Verify correct phone number is programmed.
• Dial the number programmed using a regular telephone to
determine if a [9] must be dialed or if 800 service is
blocked.
Panel does not respond to handshakes
• Verify the format programmed is supported by the central
station.
Panel transmits data multiple times without receiving a
handshake
• Verify that the account number and reporting codes are
correctly programmed.
Contact ID and Pulse formats
• Program a HEX [A] to transmit a digit [0].
SIA format
• Program a digit [0] to transmit a digit [0].
Alternate Communicator
• Refer to the Communicator installation manual for troubleshooting actions.
WWW.DIYALARMFORUM.COM
6 Testing & Troubleshooting
Trouble [5] Zone Fault
st
1 press - Zone faults
2nd press - Keypad faults
3rd press - Siren faults
4th press - Repeater fault
5th press - RF fault
Press [5] to determine specific zones with a Fault trouble
Hard-wired zone fault condition present. • Remove the wire leads from I/O and COM terminals and
A short circuit is present on one or more
measure the resistance of the wire leads.
zones with double end-of-line resistors • Connect a 5.6K resistor (Green, Blue, Red) across the I/O
enabled.
and COM terminals. Verify the trouble condition clears.
One or more wireless devices have not
• Perform a Module Placement Test – program section
checked in within the programmed time.
[904] and verify the wireless device is in a good location.
• If bad test results occur, test the wireless device in
another location. If the wireless device now tests
good, the original mounting location is bad.
• If the wireless device continues to give bad test
results, replace the wireless device.
Trouble [6] Zone Tamper
st
1 Press - Zone faults
2nd press - Keypad faults
3rd press - Siren faults
4th press - Repeater fault
Press [6] to determine specific zones with a Tamper trouble
An open circuit is present on one or more • Remove the wire leads from I/O and COM terminals and
measure the resistance of the wire leads.
zones with double end-of-line resistors
• Connect a 5.6K resistor (Green, Blue, Red) across the I/O
enabled.
and COM terminals.
• Verify the trouble condition clears.
A tamper condition is present on one or • Ensure device cover is secure.
more wireless devices.
• Ensure device is correctly mounted for wall tamper operation.
• Violate, then restore the tamper. If tamper condition persists, replace wireless device.
Trouble [7] Wireless Device Low Battery Press [7] to scroll through specific devices with a Low Battery
Trouble
1st press - Wireless Zones
2nd press - Wireless Keys
3rd press - Wireless Keypads
4th press - Wireless Sirens
5th press - Wireless Proximity
Tags
6th press - Repeater
One or more wireless devices has a low
battery.
Replace Battery
• Verify zone operation.
• Verify that tamper and low battery condition is cleared
NOTE: The event is not logged to the
and reported.
event buffer until the wireless device low • Flashing Trouble LED on keypad indicates low battery.
battery delay time expires.
To determine which indoor siren is in low battery, press
the Test button. If no test indications are sounded, replace
Program section [377] Opt 9.
batteries.
• To determine which outdoor siren is in low battery,
remove and reconnect battery. If strobe does not flash,
replace battery.
• If a proximity tag is in low battery, the tag must be deleted
and replaced before the trouble is cleared from [*][2].
Note: Replacing batteries causes a tamper. Replacing cover
restores the tamper and sends the associated reporting codes
to the central station.
Trouble [8] Loss of Clock/Date
Loss of time and date
The main panel internal clock is not set.
To program the time and date:
• Enter [][6][Master Code] then Press [1].
• Enter the time and date (in military) using the following
format: HH:MM MM/DD/YY
Example.
For 6:00 pm, Nov. 30, 2007
Enter: [18] [00] [11] [30] [07]
WWW.DIYALARMFORUM.COM
69
SCW9055/57 Wireless Alarm System
Appendix A: Reporting Code Formats
The following tables contain Contact ID and Automatic SIA format reporting codes. See Programming Sections [320]-[348] for Reporting Codes.
Contact ID
The first digit (in parentheses) is automatically sent by the control. The second two digits are programmed to indicate specific information about the signal. For example, if zone 1 is an entry/exit point, you could program the event code as [34]. The central station would
receive the following:
*BURG - ENTRY/EXIT - 1 where the “1” indicates which zone went into alarm.
SIA Format - Level 2 (Hard Coded)
The SIA communication format used in this product follows the level 2 specifications of the SIA Digital Communication Standard October 1997. This format will send the Account Code along with its data transmission. The transmission will look similar to the following at the receiver:
N ri1
BA 01
N
= New Event
ri1
= Partition /Area Identifier
BA
= Burglary Alarm
01
= Zone 1
A system event will use the Area Identifier ri00. Contact ID Zone Alarm/Restore Event Codes
Section #
Reporting Code
[320]-[323] Zone Alarms
[324]-[327] Zone Restores
Code Sent When...
Automatic
Dialer
Contact ID
Direction*
Codes
Zone goes into alarm
Alarm condition has been restored
A/R
A/R
[328]
[328]
[328]
[328]
Duress Alarm
Duress code entered at keypad
Opening After Alarm
System disarmed with alarm in memory
Recent Closing
Alarm occurs within two minutes of system arming
Cross Zone (Police Code) Two zones on the same partition go into alarm during
Alarm
any given armed-to-armed period (incl. 24Hr zones)
[328]
Burglary Not Verified
This event is transmitted when a second cross zone
alarm does not occur within the cross zoning time
[328]
Alarm Cancelled
Sent when the system is disarrmed after an alarm, but
before the expiry of the alarm cancellation timer
[329]
[F] Key Alarm/Rest.
Keypad fire alarm (alarm and restore rep. codes sent
together)
[329]
[A] Key Alarm/Rest.
Keypad auxiliary alarm (alarm and restore rep. codes
sent together)
[329]
[P] Key Alarm/Rest.
Keypad panic alarm (alarm and restore rep. codes sent
together)
[329]
Fail to Report In
A zone was not tripped between the inactivity monitoring
windows
[330]-[337] Zone Tamper/Restore
Zone is tampered / tamper condition restored
A/R
A/R
A/R
A/R
See the tables on page 72 for
details
E(1)21-000
HA-00
E(4)58-000
OR-00
E(4)59-UUU CR-UU
E(1)39-000
BM-00/BV-00
A/R
E(3)78-000
BG-00
A/R
E(4)A6-UUU
OC-UU
A/R
E(1)1A-000
R(1)1A-000
E(1)AA-000
R(1)AA-000
E(1)2A-000
R(1)2A-000
E(1)A2-000
FA-00/FH-00
A/R
A/R
A/R
T/R
[338]
General System Tamper/ Case/cover has a tamper alarm. Case/cover tamper
T/R
Rest.
restored
[338]
Keypad Lockout
Maximum number of incorrect access codes has been T/R
entered at a keypad
[339-341]
Closings
System armed (user 01-16, 40 indicated)
O/C
[341]
Automatic Zone Bypass
A zone was bypassed at the time of arming
O/C
[341]
Partial Closing
One or more zones bypassed when system armed
O/C
[341]
Special Closing
Closing (arming) using one of the following methods:
O/C
quick arm, keyswitch, function key, maintenance code,
DLS software, wireless key
[341]
Exit Fault
Sent when an exit error occurs and the Entry Delay
O/C
expires before the system is disarmed
[342-344]
Openings
System disarmed (user 01-16, 40 indicated)
O/C
[344]
Special Opening
Opening (disarming) using one of the following:
O/C
keyswitch, maintenance code, DLS software, wireless key
[344]
Late to Open
The system was not disarmed when the late to open time O/C
expired
[345]-[346] Battery Trouble/Rest.
SCW System battery is low/battery restored.
MA/R
[345]-[346] AC Line Trouble/Rest.
[345]-[346]
70
Fire Trouble/Rest.
AC power to control panel is disconnected /AC power
restored (Both codes follow AC Failure Comm. Delay.)
Trouble occurs/restore on a fire zone
SIA Auto
Rep Codes**
MA/R
MA/R
MA-00/MH-00
PA-00/PH-00
NA-00
E(3)83-ZZZ
R(3)83-ZZZ
E(1)45-000
R(1)45-000
E(4)61-000
TA-ZZ/TR-ZZ
E(4)A1-UUU
E(5)7A-ZZZ
E(4)56-000
E(4)AA-000
CL-UU
UB-ZZ
CG-00
CL-00
E(3)74-ZZZ
EA-ZZ
E(4)A1-UUU
E(4)AA-000
OP-UU
OP-00
E(4)53-000
CT-00
E(3)A2-000
R(3)A2-000
E(3)A1-000
R(3)A1-000
E(3)73-000
R(3)73-000
YT-00/YR-00
WWW.DIYALARMFORUM.COM
ES-00/EJ-00
JA-00
AT-00/AR-00
FT-00/FH-00
Appendix A: Reporting Code Formats
Section #
Reporting Code
Code Sent When...
Automatic
Dialer
Contact ID
Direction*
Codes
SIA Auto
Rep Codes**
[345]-[346]
Auxiliary Power Trouble/
Rest.
TLM Fail/Restore
Aux voltage supply trouble/restore
MA/R
YP-00/YQ-00
Telephone line restored
MA/R
[346]
[345]-[346]
Gen. System Trouble/Rest. Hardware fault, LCD Loss, Repeater AC Loss or RF Jam
trouble has occurred/ been restored.
[345]-[346] Gen. System Supervisory Control panel has detected an alternate communicator
Trouble/Rest.
fault/communications restored.
[346]
Cold Start
The SCW9055/57 has restarted after total power loss.
[347]
Phone# 1 to 4 FTC Restore Control panel has restored communications to central
station on Phone# 1 to 4 (after FTC)
[347]
DLS Lead In
Downloading session start
[347]
DLS Lead Out
Downloading session complete
[347]
Zone Fault/Rest.
One or more zones have faults/restored
MA/R
MA/R
MA/R
[347]
MA/R
MA/R
MA/R
MA/R
[347]
Programmed amount of time (days or hours) for
delinquency has expired without zone activity or without
system being armed
Wireless Zone Low Battery Wireless zones have low battery trouble/has been
Trouble/Rest.
restored
Wireless Device Low
Wireless panic pendants and wireless keys have low
Battery Trouble/Rest.
battery/all low batteries restored
Keypad 1 Low Battery/
Keypad 1 has a low battery trouble/has been restored
Rest.
Siren 1 Low Battery/Rest. Siren 1 has a low battery trouble/has been restored
[347]
Siren 2 Low Battery/Rest.
Siren 2 has a low battery trouble/has been restored
[347]
Repeater 1 has a low battery trouble/has been restored MA/R
[347]
Repeater 1 Low Battery/
Rest.
Repeater 2 Low Battery/
Rest.
Repeater 3 Low Battery/
Rest.
Repeater 4 Low Battery/
Rest.
Installer Lead In
Installer Lead out
Keypad 1 Fault/Rest.
[347]
Siren 1 Fault/Rest.
[347]
Siren 2 Fault/Rest.
[347]
Repeater 1 Fault/Rest.
[347]
Repeater 2 Fault/Rest.
[347]
Repeater 3 Fault/Rest.
[347]
Repeater 4 Fault/Rest.
[347]
[348]
Panel Firmware Update
Begin/ Successful
Walk Test Begin/End
[348]
[348]
[609]
Periodic Test
System Test
Keypad Tamper/Rest.
[609]
[347]
[347]
[347]
[347]
[347]
[347]
[347]
Delinquency
MA/R
MA/R
MA/R
MA/R
MA/R
MA/R
Repeater 2 has a low battery trouble/has been restored MA/R
Repeater 3 has a low battery trouble/has been restored MA/R
Repeater 4 has a low battery trouble/has been restored MA/R
Installer Programming has been entered
Installer Programming has been exited
A wireless supervision fault has occurred/been restored
for Keypad 1
A wireless supervision fault has occurred/been restored
for siren 1
A wireless supervision fault has occurred/been restored
for siren 2
A wireless supervision fault has occurred/been restored
for Repeater 1
A wireless supervision fault has occurred/been restored
for Repeater 2
A wireless supervision fault has occurred/been restored
for Repeater 3
A wireless supervision fault has occurred/been restored
for Repeater 4
A local firmware update has begun/ was completed
successfully
Beginning of test/End of test
MA/R
MA/R
MA/R
MA/R
MA/R
MA/R
MA/R
MA/R
MA/R
MA/R
T
T
T
T/R
Siren 1 Tamper/Rest.
Periodic system test transmission
[*][6] bell/communications test
A tamper condition has been detected/restored from
Keypad 1
Tamper condition detected/restored for siren 1
[609]
Siren 2 Tamper/Rest.
Tamper condition detected/restored for siren 2
T/R
[610]
Alternate Communicator
The Atl. Comm. has detected receiver 1 has gone
Receiver 1 Trouble/Restore absent or failed to initialize/is present and has been
initialized
T/R
MA/R
E(3) 12-000
R(3) 12-000
E(3) 51-000
R(3) 51-000
E(3) AA-000
R(3) AA-000
E(3) 3A-000
R(3) 3A-000
E(3) A5-000
E(3) 54-000
LT-01/LR-01
YX-00/YZ-00
ET-00/ER/00
RR-00
YK-00
E(4) 11
E(4) 12
E(3) 8A-ZZZ
R(3) 8A-ZZZ
E(6) 54-000***
RB-00
RS-00
UT-ZZ/UJ-ZZ
E(3) 84-ZZZ
R(3) 84-ZZZ
E(3) 84-000
R(3) 84-000
E(3) 84-070
R(3) 84-070
E(3) 84-080
R(3) 84-080
E(3) 84-081
R(3) 84-081
E(3) 84-090
R(3) 84-090
E(3) 84-091
R(3) 84-091
E(3)84-092
R(3)84-092
E(3)84-093
R(3)84-093
E(6)27-000
E(6)28-000
E(3)8A-070
R(3)8A-070
E(3) 8A-080
R(3) 8A-080
E(3) 8A-081
R(3) 8A-081
E(3) 8A-090
R(3) 8A-090
E(3) 8A-091
R(3) 8A-091
E(3) 8A-092
R(3) 8A-092
E(3) 8A-093
R(3) 8A-093
E(9)03-003/
R(9)03-003
E(6)A7-UUU
R(6)A7-UUU
E(6)A2-000
E(6)A1-000
E(3)83-070
R(3)83-070
E(3)83-080
R(3)83-080
E(3) 83-081
R(3) 83-081
E(3)5A-001
R(3)5A-001
XT-ZZ/XR-ZZ
WWW.DIYALARMFORUM.COM
CD-00
XT-00/XR-00****
XT-70/XR-70
XT-80/XR-80
XT-81/XR-81
XT-90/XR-90
XT-91/XR-91
XT-92/XR-92
XT-93/XR-93
LB-00
LS-00
UT-70/UJ-70
UT-80/UJ-80
UT-81/UJ-81
UT-90/UR-90
UT-91/UR-91
UT-92/UR-92
UT-93/UR-93
LB-00/LS-00
TS-UU/TEUU
RP-00
RX-00
TA-70/TR-70
TA-80/TR-80
TA-81/TR-81
YS-01/YK-01
71
SCW9055/57 Wireless Alarm System
Section #
Reporting Code
[610]
Alternate Communicator
The Atl. Comm. has detected receiver 2 has gone
Receiver 2 Trouble/Restore absent or failed to initialize/is present and has been
initialized
General Alternate
The Atl. Comm. has detected/restored a Radio/SIM
Communicator Trouble/
failure, Cellular Trouble, Ethernet Trouble, or SMS
Restore
Config Trouble
Repeater 1 Tamper/Rest. Tamper condition detected/restored for Repeater 1
[610]
[611]
[611]
[611]
[611]
[611]
[611]
[611]
[611]
*
**
***
****
Code Sent When...
Automatic
Dialer
Contact ID
Direction*
Codes
SIA Auto
Rep Codes**
MA/R
E(3)5A-001
R(3)5A-001
YS-02/YK-02
MA/R
E(3)AA-001
R(3)AA-001
YX-01/YR-01
T/R
E(3)83-090
TA-90/TR-90
R(3)83-090
Repeater 2 Tamper/Rest. Tamper condition detected/restored for Repeater 2
T/R
E(3)83-091
TA-91/TR-91
R(3)83-091
Repeater 3 Tamper/Rest. Tamper condition detected/restored for Repeater 3
T/R
E(3)83-092
TA-92/TR-92
R(3)83-092
Repeater 4 Tamper/Rest. Tamper condition detected/restored for Repeater 4
T/R
E(3)83-093
TA-93/TR-93
R(3)83-093
Repeater 1 AC trouble/Rest. AC power loss detected/restored for Repeater 1
T/R
E(3)A1-090
AT-90/AR-90
R(3)A1-090
Repeater 2 AC trouble/Rest. AC power loss detected/restored for Repeater 2
T/R
E(3)A1-091
AT-91/AR-91
R(3)A1-091
Repeater 3 AC trouble/Rest. AC power loss detected/restored for Repeater 3
T/R
E(3)A1-092
AT-92/AR-92
R(3)A1-092
Repeater 4 AC trouble/Rest. AC power loss detected/restored for Repeater 4
T/R
E(3)A1-093
AT-93/AR-93
R(3)A1-093
A/R = alarms/restores; T/R = tampers/restorers; O/C = openings/closings; MA/R = miscellaneous alarms/restores; T = test
transmissions
UU = user number (user01-16,40); ZZ = zone number (01-34).
Use the “Fail to close” event code [(4)54] to report closing or activity delinquency. Ensure the central station is aware that this
code is used.
Zones and panic pendants are identified, wireless keys can be identified for openings and closings.
Contact ID Zone Alarm/Restore Event Codes
(as per SIA DCS: ‘Contact ID’ 01-1999):
Program any of these codes for zone alarms/restores when using the standard (non-automatic) Contact ID reporting format.
Zone Definition
Contact
ID Auto
Rep
Codes
Delay 1
BA-ZZ/BH-ZZ (1) 3A
Delay 2
BA-ZZ/BH-ZZ (1) 3A
Instant
BA-ZZ/BH-ZZ (1) 3A
Interior
BA-ZZ/BH-ZZ (1) 3A
Interior Stay/Away
BA-ZZ/BH-ZZ (1) 3A
Delay Stay/Away
BA-ZZ/BH-ZZ (1) 3A
24-Hr. Supervisory
US-ZZ/UR-ZZ (1) 5A
24-Hr. Supervisory Buzzer
UA-ZZ/UH-ZZ (1) 5A
24-Hr. Burg
BA-ZZ/BH-ZZ (1) 3A
24-Hr. Gas
GA-ZZ/GH-ZZ (1) 51
24-Hr. Heat
FA-ZZ/FH-ZZ (1) 58
24-Hr. Medical
MA-ZZ/MH-ZZ (1) AA
24-Hr. Panic
PA-ZZ/PH-ZZ (1) 2A
24-Hr. Emergency
QA-ZZ/QH-ZZ (1) A1
24-Hr. Water
WA-ZZ/WH-ZZ (1) 54
24-Hr. Freeze
ZA-ZZ/ZH-ZZ (1) 59
Interior Delay
BA-ZZ/BH-ZZ (1) 3A
Instant Stay/Away
BA-ZZ/BH-ZZ (1) 3A
24-Hr. Non-latching Tamper
TA-ZZ/TR-ZZ (3) 83
Day Zone
BA-ZZ/BH-ZZ (1) 3A
Night Zone
BA-ZZ/BH-ZZ (3) 83
Delayed 24-Hr. Fire (Wireless)
FA-ZZ/FH-ZZ (1) 1A
Standard 24-Hr. Fire (Wireless)
FA-ZZ/FH-ZZ (1) 1A
24-Hr. Auto Verified Fire (Wireless) FA-ZZ/FH-ZZ (1) 1A
24-Hr. CO Alarm
GA-ZZ/GH-ZZ (1) 62
ZZ = zones 01-34
72
SIA Auto Rep
Codes
SIA Format Automatic Zone Alarm/Restore Codes
Medical Alarms
(1)AA Medical
(1)A1 Pendant Transmitter
(1)A2 Fail to Report In
Fire Alarms
(1)1A Fire Alarm
(1)11 Smoke
(1)12 Combustion
(1)13 Water Flow
(1)14 Heat
(1)15 Pull Station
(1)16 Duct
(1)17 Flame
(1)18 Near Alarm
Panic Alarms
(1)2A Panic
(1)21 Duress
(1)22 Silent
Burglar Alarms
(1)3A Burglary
(1)31 Perimeter
(1)32 Interior
(1)33 24 Hour
(1)34 Entry / Exit
(1)35 Day / Night
(1)36 Outdoor
(1)37 Tamper
(1)38 Near Alarm
General Alarms
(1)4A General Alarm
(1)43 Exp. Module Failure
(1)44 Sensor Tamper
(1)45 Module Tamper
(1)4A Cross Zone Police Code
24 Hour Non-Burglary
(1)5A 24 Hour non-Burg
(1)51 Gas Detected
(1)52 Refrigeration
(1)53 Loss of Heat
(1)54 Water Leakage
(1)55 Foil Break
(1)57 Low Bottled Gas Level
(1)58 High Temp
(1)59 Low Temp
(1)61 Loss of Air Flow
(1)34 Entry / Exit
WWW.DIYALARMFORUM.COM
Appendix B: 2-Way Audio Verification (SCW9057 only)
Appendix B: 2-Way Audio Verification (SCW9057 only)
The following information is intended for use by the Central Station Operator.
•
The SCW9057 Audio Verification provides Talk and Listen-in capability for audio verification of alarms. This allows the central station to communicate with the occupants through the microphone and speaker of the alarm system.
•
After one or more alarms have been sent to the central station, the system holds the line for 90 seconds. During this period, the siren continues to
sound, indicating that a 2-way voice session is available and may be initiated. If any key is pressed by the user during this time, a 90-second 2-way
voice session begins in low gain listen-in only mode. The siren is silenced for the duration of the 2-way voice session and all microphones are
turned on. When the 2-way session terminates, the siren turns back on unless it has timed out.
•
The commands indicated below are a subset of the SIA Audio Verification Standard (November 11, 1997).
The 2-way Audio Session
1.
Zone Violation: A 2-way audio session begins with the violation of a zone that has zone attribute 9 enabled.
By default, the following do NOT initiate a 2-way session:
•
Supervisory, zone 9
•
Keyswitch zones, zone 22 and 23
•
24-Hour Non-Alarm (local), zone 26
•
24-Hour Non-Latching Tamper, zone 36
•
24-Hour Carbon Monoxide (wireless), zone 81
•
Fire Zones, zone 87, 88, 89 and the Fire Key
For more information, see section [101]-[134], attribute 9 in Chapter 5.
By default 1-way audio (Listen-in only) is initiated by the following:
•
Silent Panic events (Silent [P], Silent Panic zone)
•
Duress alarm
2. Communication to the Monitoring Station: One of the reporting codes/actions listed below is sent to the monitoring station when the appropriate alarm is triggered.
Format
Reporting Code/Event
SIA
L90
Contact ID
606
BPS
Communicates the Event, then automatically enters into 2-way Audio mode.
3.
Alerting the Operator: When the reporting code is received by the monitoring station or a 2-way session is automatically initiated, a 2-way Initiation (Start) tone will be sounded to alert the operator. A high (1800 Hz) tone and a low (900 Hz) tone are used to generate the tones listed below.
Short tone duration is 100ms. Long tone duration is 1 second.
2-way Initiation (Start) Tone:
3 Hi Tones (Short)
After the third short Hi tone has sounded, the panel switches directly into ‘Listen-in” mode without a keypress from the monitoring
station.
Reminder Tones:
1 Hi Tone (Short)
1 Short hi tone indicates 20 seconds are left in the audio session.
1 low Tone
1 Short low tone indicates 10 seconds are left in the audio session.
Subsequent Alarm:
1 Hi Tone Long
1 long hi tone indicates a new alarm event if Section [023] Option 6 (New Alarms will not disconnect 2-way Audio) is enabled,
alarms are delayed. If disabled the audio session will terminate.
NOTE: Receiving a subsequent alarm event tone will not restart the 90 second session timer.
Subsequent Fire Event:
Hi, Low, Hi
(Short)
4.
3 short (100ms) tones Hi, Low, Hi indicates a new Fire alarm if Section [023] Option 6 (New Alarms will not disconnect 2-way
Audio) is enabled. If disabled the audio session will terminate.
NOTE: Receiving a subsequent alarm event tone will not restart the 90 second session timer.
Initiating, Control and Termination of the Session: The Operator controls the session the using the Audio Control Telephone Key Functions
listed in the table below. To select the commands, press [*][0] followed by the key number(s) indicated below:
Key
Command
1/4
Talk to Speaker
Description
Connects the monitoring station to the speaker.
2
VOX Mode
Connects the monitoring station to the system in VOX Mode (see VOX Support below).
3/6
Listen to Microphone
Connects the monitoring station to the microphone.
4
Lo-Gain Talk to Speaker
Connects the monitoring station to the speaker at the low volume output level.
6
Lo-Gain Listen to Microphone
Connects the monitoring station to the microphone at the low gain input level.
7
Extend Time
Restarts the session timer (90 seconds) to prevent timeout. To extend the time and take no other action use
this function. Pressing any key automatically extends the time.
99
Disconnect
Disconnects the session. The second “9” must be pressed within 1 second of pressing the first “9.” Use the
“Disconnect” key sequence before hanging up during a Talk / Listen-In session.
VOX Support: When in VOX mode the alarm panel automatically switch between the phone line and internal microphone/speaker being active depending on which one is loudest. Push to Talk overrides VOX – this is performed by switching into a talk mode at the monitoring station.
Hang-up Auto-detection: The alarm panel automatically disconnects if the central station receiver disconnects before the operator picks up the line.
The panel will consider five seconds of continuous dial tone, or busy tone to be a disconnect condition.If the operator does NOT terminate the call using
the disconnect command (99), the alarm panel will consider five seconds of continuous dial tone, or busy tone to be a disconnect condition.
Bell/Buzzer Silent During 2-Way Audio: When the panel has an audible alarm, the bell can be programmed to remain active until the 2-Way Audio
session starts and then the bell will be silent (Section [600], option 7 off) to allow the user to hear the operator. All buzzer activity, except keypresses,
will be silent when 2-way audio is active. If the panel has not been disarmed at the termination of the 2-Way Audio session, the bell will restart for the
timeout duration. Door chime is disabled during a 2-way Audio session. Any activity that normally sounds door chime will occur and the door chime
will not sound.
WWW.DIYALARMFORUM.COM
73
SCW9055/57 Wireless Alarm System
Appendix C: Communicator Format Options
The following format options are programmable in section [350] on page 27
01 20 BPS, 1400 Hz handshake
02 20 BPS, 2300 Hz handshake
• BPS Formats - 0 is not valid in Account or Rep Code (A must be used).
Depending on the pulse format, the panel communicates using the following: 3/1, 3/2, 4/1 or 4/2, 1400 or 2300 Hz handshake, 20 bits per second, non-extended.
Digit “0” sends no pulses and is used as a filler. When programming account numbers enter four digits. When programming a three digit account number the fourth
digit must be programmed as a “0” which will act as a filler digit. If an account number has a “0” in it, substitute a HEX digit “A” for the “0.”
Examples:
• 3 digit account number [123]- program [1230]
• 3 digit account number [502] - program [5A20]
• 4 digit account number [4079] - program [4A79]
Two digits must be entered when programming reporting codes. If one digit reporting codes are used, the second digit must be programmed as “0”. If “0” is to be transmitted, substitute a HEX digit “A” for the “0”.
Examples:
• 1 digit reporting code [3] - program [30]
• 2 digit reporting code [30] - program [3A]
To prevent the panel from reporting an event, program the reporting code for the event as [00] or [FF].
03 DTMF Contact ID
• ADEMCO Contact ID - 0 is not valid in Account or Rep Code (A must be used, 10 in checksum)
Contact ID is a specialized format that communicates information quickly using tones rather than pulses. The format also allows more information to be sent. For
example, rather than reporting an alarm zone 1, the Contact ID format can also report the type of alarm, such as Entry/Exit alarm zone 1.
If Contact ID Sends Automatic Reporting Codes is selected, the panel automatically generates a reporting code for each event. These identifiers are listed in Appendix A. If the Automatic Contact ID option is not selected, reporting codes must be programmed. The 2-digit entry determines the type of alarm. The panel automatically
generates all other information, including the zone number.
NOTE:If Automatic Contact ID is selected, the panel automatically generates all zone and access code numbers, eliminating the need to program these items.
NOTE:The zone number for Zone Low Battery and Zone Fault events will not be identified when Pulse formats are used.
If the Contact ID uses Automatic Reporting Codes option is enabled, the panel will operate as follows:
• If an event’s reporting code is programmed as [00], the panel will not attempt to call the central station.
• If the reporting code for an event is programmed as anything from [01] to [FF], the panel automatically generates the zone or access code number. See Appendix A
for a list of transmitted codes.
If the Contact ID uses Programmed Reporting Codes option is enabled, the panel will operate as follows:
• If an event’s reporting code is programmed as [00] or [FF], the panel will not attempt to call central station.
• If the reporting code for an event is programmed as anything from [01] to [FE], the panel will send the programmed reporting code.
Account numbers must be four digits:
• If the digit “0” is in the account number substitute the HEX digit “A” for the “0.”
• All reporting codes must be two digits.
• If the digit “0” is in the reporting code substitute the HEX digit “A” for the “0.”
• To prevent the panel from reporting an event, program the reporting code for the event as [00] or [FF].
See: Contact ID Sends Automatic Reporting Codes section [381], Option [7]
04 SIA FSK
• SIA -0 is valid in Account or Rep Code (not 00 in a Reporting code)
• SIA -0 uses 300 Baud FSK as the communication media. Account Code can be 4 or 6 hexadecimal digits. Reporting codes must be 2 digits. The SIA format
transmits a 4 (or 6) digit account code, 2 digit identifier code and 2 digit reporting code. The 2 digit identifier is pre programmed by the panel.
SIA is a specialized format that communicates information quickly using frequency shift keying (FSK) rather than pulses. The SIA format automatically generates the type of signal being transmitted, such as Burglary, Fire, Panic etc. The two digit reporting code is used to identify the zone or access code number.
If the SIA format is selected the panel can be programmed to automatically generate all zone and access code numbers eliminating the need to program these items.
If the SIA Sends Automatic Reporting Codes option is enabled the panel will operate as follows:
1. If the reporting code for an event is programmed as [00] the panel will not attempt to call the central station.
2. If the reporting code for an event is programmed as anything from [01] to [FF] the panel will AUTOMATICALLY generate the zone or access code number.
3. During a partial closing, all bypassed zones are reported.
Communicator Call Direction Options can be used to disable reporting of events such as Openings/Closings. Also, if all the Opening/Closing reporting codes were
programmed as [00] the panel would not report.
If the SIA Sends Automatic Reporting Codes option is disabled the panel operates as follows:
1. If the reporting code for an event is programmed as [00] or [FF] the panel will not attempt to call the central station.
2. If the reporting code for an event is programmed as anything from [01] to [FE] the panel will send the programmed reporting code.
3. During a partial closing, bypassed zones are not reported.
NOTE:The zone number for Zone Low Battery and Zone Fault events will not be identified when Programmed SIA is used.
See: SIA Sends Automatic Reporting Codes - Section [381], Option [3],
Communicator Call Direction Options - Section [351] to [376],
SIA Identifiers - Appendix A
06 Residential Dial
If Residential Dial is programmed and an event that is programmed to communicate occurs, the panel will seize the line and dial the appropriate telephone number(s). Once
the dialing is complete, the panel will emit an ID tone and wait for a handshake (press a 1, 2, 4, 5, 7, 8, 0,  or # key from any telephone). It will wait for this handshake for
the duration of Post Dial Wait for Handshake timer. Once the panel receives the handshake, it will emit an alarm tone over the telephone line for 20 seconds. If several
alarms occur at the same time, only one call will be made to each telephone number the panel is programmed to call.
74
WWW.DIYALARMFORUM.COM
Appendix D: Regulatory Approvals Information
Appendix D: Regulatory Approvals Information
North America
will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service.
FCC COMPLIANCE STATEMENT
Equipment Maintenance Facility
CAUTION: Changes or modifications not expressly approved by
Digital Security Controls could void your authority to use this
equipment.
If trouble is experienced with this equipment (SCW9055) for repair or warranty information, contact the facility indicated below. If the equipment is causing harm to the
telephone network, the Telephone Company may request that you disconnect the
equipment until the problem is solved. This equipment is of a type that is not intended
to be repaired by the end user.
DSC c/o APL Logistics 757 Douglas Hill Rd., Lithia Springs, GA 30122
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Re-orient the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/television technician for help.
The user may find the following booklet prepared by the FCC useful: “How to
Identify and Resolve Radio/Television Interference Problems”. This booklet is
available from the U.S. Government Printing Office, Washington D.C. 20402,
Stock # 004-000-00345-4.
Additional Information
Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information.
Alarm dialing equipment must be able to seize the telephone line and place a call in an
emergency situation. It must be able to do this even if other equipment (telephone,
answering system, computer modem, etc.) already has the telephone line in use. To do
so, alarm dialing equipment must be connected to a properly installed RJ-31X jack
that is electrically in series with and ahead of all other equipment attached to the same
telephone line. Proper installation is depicted in the figure below. If you have any
questions concerning these instructions, you should consult your telephone company
or a qualified installer about installing the RJ-31X jack and alarm diadialingling
equipment for you.
Customer Premises Equipment and Wiring
Network
Service
Provider's
Facilities
Alarm Dialing
Equipment
IMPORTANT INFORMATION
This equipment complies with Part 68 of the FCC Rules and, if the product was
approved July 23, 2001 or later, the requirements adopted by the ACTA. On the
side of this equipment is a label that contains, among other information, a product
identifier. If requested, this number must be provided to the Telephone Company.
Product Identifier
US:F53AL01B9057 USOC Jack:RJ-31X
Telephone Connection Requirements
A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is
provided with this product. It is designed to be connected to a compatible modular
jack that is also compliant. See installation instructions for details.
Ringer Equivalence Number (REN)
The REN is used to determine the number of devices that may be connected to a
telephone line. Excessive RENs on a telephone line may result in the devices not
ringing in response to an incoming call. In most but not all areas, the sum of
RENs should not exceed five (5.0). To be certain of the number of devices that
may be connected to a line, as determined by the total RENs, contact the local
Telephone Company. For products approved after July 23, 2001, the REN for this
product is part of the product identifier that has the format US:
AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal
point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown
on the label.
REN = 0.1B
Incidence of Harm
If this equipment (SCW9055/57(D)(G)(I)(-SM)-433) causes harm to the telephone network, the telephone company will notify you in advance that temporary
discontinuance of service may be required. But if advance notice is not practical,
the telephone company will notify the customer as soon as possible. Also, you
will be advised of your right to file a complaint with the FCC if you believe it is
necessary.
Changes in Telephone Company Equipment or Facilities
The Telephone Company may make changes in its facilities, equipment,
operations or procedures that could affect the operation of the equipment. If this
happens the Telephone Company
Computer
RJ-31X
Jack
Unused
RJ-11 Jack
Telephone
Line
Telephone
Network
Demarcation
Point
Fax Machine
Telephone
Answering
System
Unused
RJ-11 Jack
Telephone
INDUSTRY CANADA STATEMENT
NOTICE: This product meets the applicable Industry Canada technical specifications.
Le présent materiel est conforme aux specifications techniques applicables d’Industrie
Canada.
The Ringer Equivalence Number (REN) for this terminal equipment is 0.1. L'indice
d'équivalence de la sonnerie (IES) du présent matériel est de 0.1.
The Ringer Equivalence Number is an indication of the maximum number of devices
allowed to be connected to a telephone interface. The termination on an interface may
consist of any combination of devices subject only to the requirement that the sum of
the RENs of all the devices does not exceed five.
L’indice d’équivalence de la sonnerie
(IES) sert à indiquer le nombre maximal de terminaux qui peuvent être raccordés à une
interface téléphonique. La terminaison d’une interface peut consister en une combinaison quelconque de dispositifs, à la seule condition que la somme d’indices d’équivalence de la sonnerie de tous les dispositifs n’excède pas 5.
The term “IC:” before the radio certification number only signifies that Industry Canada technical specifications were met.
Certification Number:
IC: IC:160A-9057 (Models SCW9055/57-433)
IC:160A-9057G (Models SCW9055/57(D)(G)(I)(-SM)-433
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference
that may cause undesired operation of the device.
Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS (s).
Le fonctionnement est soumis aux deux conditions suivantes: (1) cet appareil ne peut
pas provoquer d'interférences et (2) cet appareil doit accepter toute interférence, y
compris les interférences qui peuvent causer un mauvais fonctionnement de l' appareil.
WWW.DIYALARMFORUM.COM
75
SCW9055/57 Wireless Alarm System
This product has been tested and found in compliance with the following standards:
UL1023 Household Burglar-Alarm System Units
UL985 Household Fire Warning System Units
UL1635 Digital Alarm Communicator System Units
ULC-S545-02Residential Fire Warning System Control Units
ORD-C1023-1974Household Burglar-Alarm System Units
This product has also been tested and found in compliance with the ANSI/SIA CP-01-2010 Control Panel Standard – Features for False
Alarm Reduction.
This product is UL/ULC listed under the following categories:
UTOU/UTOUC Control Units and Accessories, Household System Type
NBSX/NBSXC Household Burglar Alarm System Units
AMTB Control Panels, SIA False Alarm Reduction
The product is labeled with the UL and ULC listing marks along with the SIA CP-01 compliance statement (Also Classified in accordance with SIA-CP-01 Standard) as proof of compliance with the above mentioned standards. For further information on this product’s
listings please also refer to the official listing guides published at the UL web site (www.ul.com) under Certifications Section.
UL/ULC Residential Fire and Burglary Installations:
For ULC Installations refer to the Standard for the Installation of Residential Fire Warning Systems, CAN/ULC-S540.
•
All burglary-type zones shall be configured with SEOL or DEOL configuration
(refer to section [133] and [134], bit 15 or 16 shall be ON)
•
Use at least one WS4916 Smoke Detector for Fire Installations (refer to section [001], fire zone shall be programmed as type 89)
•
The entry delay shall not exceed 60 seconds (refer to section [005])
•
The exit delay shall not exceed 120 seconds (refer to section [005])
•
The minimum Bell Time-out is 4 minutes (refer to section [005])
Note: For ULC Residential Fire Installations the minimum Bell Time-out is 5 minutes
•
Temporal Three Fire Signal shall be enabled (refer to section [013], option 8 shall be ON)
•
Arm/Disarm Bell Squawk shall be enabled when using wireless key WS4939 (refer to section [014], option 1 shall be ON)
•
Auxiliary Power boost shall be enabled (refer to section [014], option 4 shall be ON)
•
A code shall be required for bypassing (refer to section [015], option 5 shall be ON)
•
Trouble beeps shall be enabled (refer to section [023], option 7 shall be ON)
•
AC trouble indication LED shall be enabled (refer to Keypad Programming, section [075], options 5 and 6 shall be ON)
•
DACT Communicator shall be enabled for Supervising Station Monitoring (refer to section [380], option 1 shall be ON).
Note: The DACT communicator for this product has no line security.
•
Telephone Line Monitoring (TLM) shall be enabled (refer to section [015], option 7 shall be ON)
Note: This product is programmed to perform 5 attempts for communication of an event to the supervising station. If unsuccessful, a Fail To Communicate (FTC) trouble is generated.
•
Test transmission cycle shall be set for monthly transmission (refer to section [377])
Note: For ULC Residential installations set for daily test transmission
•
Wireless Supervision window shall be enabled (refer to Wireless Programming, sections [804] [82] to [85])
•
Wireless Supervision window shall be set to 4h for Fire Installations (refer to Wireless Programming, section [804][81] shall be
programmed with the value [16]
•
Wireless Supervision window shall be set to 24h for Burglary Installations only (refer to Wireless Programming, section [804][81]
shall be programmed with the value [96]
•
RF Jam detection shall be enabled (refer to Wireless Programming, section [804] [900], option 7 shall be OFF)
•
Bells will be active During 2-way Audio (refer to section [600], opt 7 shall be ON)
•
New Alarms will Disconnect 2-way Audio (refer to section [023], opt 6 shall be OFF)
•
When the 2- way audio feature is enabled (section [601] option 1-3 is ON) ensure that section [023] option 6 is OFF and section
[600] option 7 is ON
Programming
The notes in the programming sections describing the system configurations for UL/ULC listed installations shall be implemented.
Bell Location
The alarm sounding device (bell) shall be located where it can be heard by the person operating the security system during the daily
arming and disarming cycle.
Casual Users
The installer should caution the user(s) not to give system information (e.g. codes, bypass methods, etc.) to casual users (baby-sitters or
service people). Only the One-Time Use codes shall be given to casual users.
User Information
The installer should advise the users and note in the User’s Manual:
•
Service organization name and telephone number
•
The programmed exit time
•
The programmed entry time
•
Test system weekly
76
WWW.DIYALARMFORUM.COM
Appendix D: Regulatory Approvals Information
SIA False Alarm Reduction Installations
For a list of the defaults value programmed when the unit is shipped from the factory and for any other programming information refer to Appendix D: False Alarm Reduction.
Caution
Call Waiting Cancel (Section [382], Option 4) feature on a non-Call Waiting line will prevent successful communication to the supervising station.
Fire Alarm Verification feature (Auto Verified Fire Zone type [89]) is supported on the DSC Wireless Smoke Detector, Model WS4916. The fire alarm delay is 40s.
Notes
Programming at installation may be subordinate to other UL requirements for the intended application.
Cross zones have the ability to individually protect the intended area (e.g. motion detectors which overlap).
Cross zoning is not recommended for line security Installations nor is to be implemented on exit/entry zones.
There is a communication delay of 30 seconds in this control panel. It can be removed, or it can be increased up to 45 seconds at the option of the end user by consulting with
the installer.
Do not duplicate any reporting codes. This applies for all communication formats other than SIA or CID sending automatic programmed reporting codes.
The security system shall be installed with the sounding device activated and the communicator enabled for transmission using SIA or CID format.
SIA Feature
Programming Section
Comments
Range/Default
Requirement
Exit Time
[005], 3rd entry
Access to Entry and Exit delays and Bell Time Out for the system
Range:45- 255 seconds
Default: 60 sec.
Required
(programmable)
Progress Annunciation/
Disable - for Silent Exit
[014], Option 6 ON
Enables audible exit beeps from the keypad for the duration of exit delay
Keypads may be disabled
Default: Enabled
Allowed
Exit Time Restart
[014], Option 2 ON
Enables the exit delay restart feature
Default: Enabled
Required
Auto Stay Arm on
Un-vacated Premises
[001]-[002] Zone type 05, 06
Function Key: Stay Arming. All Stay/Away type zones (05, 06) will be automatically bypassed
If no exit after full arm
Default: Enabled
Required
Exit Time and Progress
Annunciation/Disable
or Remote Arming
[005] and [014] bit 6
System Times and Audible Exit beeps can be disabled when using the Key fob to
arm away the system
Default: Enabled
Allowed
Entry delay(s)
[005], 1st and 2nd entry
Access to Entry and Exit delays and Bell Time Out for the system
Note: Combined Entry delay and Communications Delay (Abort Window) shall
not exceed 60s
Range: 30 sec. to 4 min.
Default: 30 sees
Required
(programmable)
Abort Window
for Non-Fire zones
[101]-[134] bit 6 ON
Access to zone attributes, i.e, swinger shutdown, transmission delay and cross
zone. Individual zones attribute bit 6 (Transmission delay) is by default ON
May be disabled
by zone or zone type
Default: Enabled
Required
Abort Window - for
Non-Fire zones
[377], 4th entry
Access to the programmable delay before communicating alarms
Note: Combined Entry delay and Communications Delay (Abort Window) shall
not exceed 60s
Range: 20 - 45 sec.
Default: 30 sees
Required
(programmable)
Abort Annunciation
[382], Option 3 ON
Enables the “Communication Cancelled” message display on keypad
Annunciate that no
alarm was transmitted
Default: Enabled
Required
Cancel Annunciation
[328], 8th entry
Access to the reporting code for Alarm Cancelled
Annunciate that a
Cancel was transmitted
Default: Enabled
Required
Duress Feature
[*][5] Master Code
Option 2 ON
Do not derive code from an existing Master/User code (e.g., Master code is 1234, No 1+/- derivative of another
the duress code should not be 1233 or 1235)
user code. No duplicates with
other user codes
Default: disabled
Allowed
Cross Zoning
[016] Option 1
[101]-[134] bit 8 OFF
This option enables Cross Zoning for entire system. Individual zones can be
enabled for Cross zoning via Zone attribute bit 8 in sections [101] - [134]
Programming required
Default: Disabled
Required
Cross Zone Timer
[176]
Access to the programmable Cross Zone timer
May program
Range: 001-255 sec./min.
Default: 60 seconds
Allowed
For all non-fire zones
shut down at 1 or 2 trips
Default: 2 trips
Required
(programmable)
Swinger Shutdown for Alarms Access to the swinger shutdown limit for zone alarms.
[377] 1st entry
Swinger Shutdown Enable
[101] - [134] bit 6 ON
Access to zone attributes, i.e., swinger shutdown, transmission delay and cross
For non-police
zone. Individual zones attribute bit 6 (Swinger shutdown enabled) is by default ON response zones
Default: Enabled
Allowed
24-Hr. Auto_verified Fire
(Wireless) Zone type [89]
Access to 24-Hr. Auto_verified Fire (Wireless)
Activates If a restore is Not
received within the specified
time
Default: disabled
Required
Call Waiting Cancel Dial
String
[304], [382], Option 4 OFF
Access to the dialing sequence used to disable call waiting
Dependant on user phone line
Default: disabled
Required
System Test:
[*][6] Master Code, Option 4
The system activates all keypad sounders, bells or sirens for 2 seconds and all keypad lights turn on.
Refer to the User Manual (part no. 29007827).
Walk Test Mode:
[*][6] Opt 8
This mode is used to test each zone on the system for proper functionality.
Alarm Communications
During Walk Test
[382] Option 2:
Enables Communication of zone alarms while Walk Test is active.
Walk Test End and Begin
Reporting Codes
[348], 1st and 2nd Entries
Access to the reporting codes for Walk Test Begin and Walk Test End.
WWW.DIYALARMFORUM.COM
77
© 2011 Tyco International Ltd. and its Respective Companies. All Rights Reserved.
The trademarks, logos, and service marks displayed on this document are registered in the United States [or other countries]. Any
misuse of the trademarks is strictly prohibited and Tyco International Ltd. will aggressively enforce its intellectual property rights
to the fullest extent of the law, including pursuit of criminal prosecution wherever necessary. All trademarks not owned by Tyco
International Ltd. are the property of their respective owners, and are used with permission or allowed under applicable laws.
Product offerings and specifications are subject to change without notice. Actual products may vary from photos. Not all products
include all features. Availability varies by region; contact your sales representative.
Technical Support: 1-800-387-3630 (Can/US)
905-760-3000 (Intl.) www.dsc.com
Printed in Canada
29007826R004
WWW.DIYALARMFORUM.COM
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising