General Installation Instructions

General Installation Instructions
General Installation Instructions WARNING
To reduce the risk of death, injury or property damage from fire, electric shock, cuts, abrasions, falling parts and other
hazards:
• Service of the equipment must be performed by qualified service personnel.
• Installation and maintenance must be performed by a person familiar with the construction and operation of this product
and any hazards involved. All applicable codes and ordinances must be followed.
• Read this document before installing, servicing or maintaining this equipment or installing a lamp. These instructions do
not cover all installation, service and maintenance situations. If your situation is not covered, or, if you do not
understand these instructions or additional information is required, contact Peerless Lighting or your local Peerless
Lighting distributor.
• Read and follow all warnings and instructions provided by the lamp manufacturer.
WARNING
Before installing, servicing or maintaining this equipment, follow these general precautions. To reduce the risk of
electrocution:
• Make sure the equipment is properly grounded.
• Always de-energize the circuit and/or equipment before connecting to, disconnecting from or servicing the equipment.
To prevent luminaire row from over-current:
• By adding the input current of each luminaire section marked on the luminaire, the total current per power feed must not
exceed the maximum line wire amperage marked on the luminaire and the power feed cord/wire amperage rating
whichever is the least.
To reduce the risk of fire:
• Keep material away that can burn from hot lamp.
• Make sure lamps are correctly installed.
• Use supply conductors with a minimum installation temperature rating as specified on equipment.
To reduce the risk of personal injury from cuts, abrasions or falling parts:
• Wear gloves to prevent cuts or abrasions from sharp edges when removing from carton, handling and maintaining this
equipment.
• Do not use abrasive materials, glass cleaners or other solvents on reflector or lens. These substances may damage
equipment and cause parts to eventually break and fall.
• Do not install a damaged fixture.
CAUTION
Observe lamp manufacturer’s recommendations and restrictions on lamp operation including but not limited to ballast
type, burning position, replacement and cycling. Use only lamps that comply with applicable ANSI standards.
NOTICE: If lamp is marked
it contains mercury. Follow disposal laws. See www.lamprecycle.org
Peerless Lighting, a division of Acuity Brands Lighting, Inc., assumes no responsibility for
claims arising out of improper or careless installation or handling of this product.
SAVE THESE INSTALLATION INSTRUCTIONS
Part Number: PIN004100 Revision: E Effective Date: 07/2012 ECO3665
PIN000100
UNIVERSAL MOUNTING
FEED LOCATION
INSTALLATION INSTRUCTION
PEERLESS LIGHTING
2246 5TH STREET, BERKELEY CA.94710
TEL: 510-845-2760 FAX: 510-845-2776
WEB SITE: WWW.PEERLESS-LIGHTING.COM
Rev. C 09/10 ECO 3606
These installation instructions are for installing the F1 Mounting Kit at FEED Location.
CAUTION: IT IS CRITICAL THAT SUPPORT LOCATIONS ARE LOCATED ACCURATELY. WE RECOMMEND THAT A LASER
DEVICE BE USED TO LINE UP THE SUPPORT LOCATIONS ON FIXTURES HAVING MORE THAN ONE SECTION. IF NOT
ALIGNED PROPERLY, A NOTICEABLE “BEND” MAY BE APPARENT WHEN VIEWED FROM THE END OF THE RUN.
WARNING: RISK OF FIRE AND ELECTRICAL SHOCK. THIS PRODUCT TO BE INSTALLED ONLY BY A QUALIFIED ELECTRICIAN.
NOTE: THIS MOUNTING ASSEMBLY IS UL AND C−UL LISTED WITH THE LUMINAIRE (UL FILE 48952).
A) Parts Not Provided by PEERLESS ---------------------------------------------------------------- page 1
B) On-Grid Installation ------------------------------------------------------------------------------------ pages 1-2
C) Off-Grid Installation ------------------------------------------------------------------------------------ page 3
A) Parts Not Provided by PEERLESS
Depending on ceiling mounting type, contractor must obtain some or all of the following parts to complete installation (see parts list):
A1 4” square x 1-½” deep J-box with ½” knockout on middle of side.
A2 J-box cover and screws.
A3 ¼-20 steel zinc plated hex head bolt (see Section D for bolt length).
A4 Caddy Bar (CADDY #512A or equal) for Off-Grid Mounting (see page 3).
BRACKET A
#10 THREAD
BRACKET B
A1
STRAIN RELIEF
CEILING GRID
CEILING MUST BE LEVEL
OR <=10° SLOPE
¼-20X3/4” BOLT OR A3
A2
NUT (FOR RECESSED
GRID ONLY)
CANOPY
ADJUSTABLE CABLE
GRIPPER SET
#10 THREAD
CUTTING SCREW
OR
BLACK BUSHING
CABLE FERRULE FOR CABLE
GRIPPER (SEE FIXTURE
INSTALLATION INSTRUCTIONS)
NOTE: THIS APPLIES TO 1/16”
DIA. CABLE ONLY
CONDUIT FITTING
WITH LOCK NUT
CORD
CABLE STUD SET
Page 1 of 4
PIN000100
UNIVERSAL MOUNTING
FEED LOCATION
INSTALLATION INSTRUCTION
PEERLESS LIGHTING
2246 5TH STREET, BERKELEY CA.94710
TEL: 510-845-2760 FAX: 510-845-2776
WEB SITE: WWW.PEERLESS-LIGHTING.COM
Rev. C 09/10 ECO 3606
B2. ON-GRID INSTALLATION STEPS:
Bend tabs straight if there
is interference with grid
Structure
Wires
For Recessed Grid
Only (See Section D)
1. Insert bolt into bottom hole of
Bracket A,
then hook Bracket
A onto grid.
2.
Hook Bracket B onto Bracket A
Bracket A
3. Adjust brackets to proper
location then screw the brackets
from A to B together. Secure the
brackets to the structure above.
Bracket A
4. Attach black bushing and conduit
fitting to J-box.
5. Hang J-Box assembly on bracket 5A. For dual feeds, hang first J-box
A tab. For single feed, screw Jwith long screw on the bracket A.
Box to brackets.
Take center knock-out on the
second J-box. Screw second Jbox to bracket B. Then add nut to
connect two boxes together.
Strain Relief
¼” MIN
1/2 White bushing
6. Insert feed cord into J-Box
through bushings and canopy.
Attach strain relief on the cord.
7. Connect wires and install the
cover to J-Box with screws.
Page 2 of 4
8. Place canopy flush with ceiling
tile. Thread cable retainer onto
bolt no less than ¼”.
PIN000100
UNIVERSAL MOUNTING
FEED LOCATION
INSTALLATION INSTRUCTION
PEERLESS LIGHTING
2246 5TH STREET, BERKELEY CA.94710
TEL: 510-845-2760 FAX: 510-845-2776
WEB SITE: WWW.PEERLESS-LIGHTING.COM
Rev. C 09/10 ECO 3606
C) Off-Grid Installation
C1. PARTS LIST
BRACKET A
#10 THREAD
CUTTING SCREW
BRACKET B
A1
CEILING MUST BE LEVEL
OR <=10° SLOPE
A4
STRAIN RELIEF
#10 THREAD
CUTTING SCREW
A2
¼-20X3/4” BOLT OR
A3
NUT
CEILING GRID
CANOPY
ADJUSTABLE CABLE
GRIPPER SET
OR
WHITE
BUSHING
CABLE FERRULE FOR
CABLE GRIPPER (SEE
FIXTURE INSTALLATION
INSTRUCTIONS)
NOTE: THIS APPLIES TO
1/16” DIA. CABLE ONLY
BLACK BUSHING
CONDUIT FITTING
WITH LOCK NUT
CABLE STUD SET
CORD
C2. OFF-GRID INSTALLATION STEPS
Bracket A
Structure
Wires
Upper slots
1. Insert bolt into Bracket A. Hook
Bracket B onto Bracket A. Secure
with nut (DO NOT TIGHTEN).
2. Slide hanger onto Caddy Bar and 3. Adjust brackets to proper location
fit Caddy Bar into upper slots in
then screw the brackets from A to
bracket.
B together. Secure the brackets
to the structure above.
Page 3 of 4
PIN000100
UNIVERSAL MOUNTING
FEED LOCATION
INSTALLATION INSTRUCTION
PEERLESS LIGHTING
2246 5TH STREET, BERKELEY CA.94710
TEL: 510-845-2760 FAX: 510-845-2776
WEB SITE: WWW.PEERLESS-LIGHTING.COM
Rev. C 09/10 ECO 3606
Grounding
Screw Hole
4. Attach black bushing and conduit
fitting to J-box.
5. Hang J-Box on bracket A tab. For
single feed, screw J-Box to
brackets.
5A. For dual feeds, hang first J-box
with long screw on bracket A.
Take center knock-out on the
second J-box. Screw second Jbox to bracket B. Then add nut to
connect two boxes together.
Strain Relief
¼” MIN
1/2 White bushing
6. Insert feed cord into J-Box
through bushing and canopy.
Attach strain relief on the cord.
7. Connect wires and install the
cover to J-Box with screws.
8. Place canopy flush with ceiling
tile. Thread cable retainer onto
bolt no less than ¼”.
D) Bolt and Nut Selection
TYPICAL GRID & TILE TYPE
ON-GRID
¼-20X3/4” HEX BOLT
B<5/16
¼-20 HEX BOLT
B>5/16
OFF-GRID
¼-20 ¼-20X3/4” HEX BOLT
HEX NUT
A<1.5 & B<5/16”
¼-20 HEX BOLT
A>1.5” OR B>5/16
¼-20
HEX NUT
YES
Use proper bolt
length to meet
min. ¼”
engagement
YES
YES
YES
Use proper bolt
length to meet
min. ¼”
engagement
YES
NO
YES
Use proper bolt
length to meet
min. ¼”
engagement
YES
TYPE 1
YES
TYPE 2
YES
NO
Use proper bolt
length to meet
min. ¼”
engagement
TYPE 3
YES
Page 4 of 4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising