technical manual - Celtic Distributors Ltd

technical manual - Celtic Distributors Ltd

TECHNICAL MANUAL

Safety, Operation, Parts, Maintenance, Service

Model:

544865C REN-O-THIN - BRIGGS & STRATTON

544877 REN-O-THIN - HONDA

WARNING: If incorrectly used this machine can cause severe injury. Those who use and maintain this machine should be trained in its proper use, warned of its dangers and should read the entire manual before attempting to set up, operate, adjust or service the machine.

2703562 REV D

CALIFORNIA

Proposition 65 Warning

Diesel engine exhaust and some of its constituents are known to the State of California to cause cancer, birth defects and other reproductive harm.

Californie Proposition 65

Avertissement

Les échappements des moteurs diesel et certains de leurs composés sont reconnus par l’Etat de Californie pour

être cancérigènes, provoquer des défauts congénitaux et d’autres dangers en matière de reproduction.

WARNING

The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.

AVERTISSEMENT

L’émission du moteur de ce matériel contient des produits chimiques que l’Etat de Californie considère être cancérigènes, provoquer des défauts congénitaux et d’autres dangers en matière de reproduction.

California Advertencia de la Proposicion 65

El estado de California hace saber que los gases de escape de los motores diesel y algunos de sus componentes producen cáncer, defectos de nacimiento y otros daños en el proceso de reproducción humana.

ADVERTENCIA

El estado de California hace saber que los gases de escape de este producto contienen productos quÍmicos que producen cáncer, defectos de nacimiento y otros daños en el proceso de reproducción humana.

© 2003, TEXTRON INC

REN-O-THIN

IMPORTANT MESSAGE

Thank you for purchasing this Ryan product. You have purchased a world class product, one of the best designed and built anywhere.

This machine comes with a Technical Manual containing safety, operation, parts, maintenance and service information. The useful life and good service you receive from this machine depends to a large extent on how well you read and understand this manual. Treat your machine properly, lubricate and adjust it as instructed, and it will give you many years of reliable service.

Your safe use of this Ryan product is one of our prime design objectives. Many safety features are built in, but we also rely on your good sense and care to achieve accident-free operation. For best protection, study the manual thoroughly. Learn the proper operation of all controls. Observe all safety precautions. Follow all instructions and warnings completely. Do not remove or defeat any safety features. Make sure those who operate this machine are as well informed and careful in its use as you are.

See a Ryan dealer for any service or parts needed. Ryan service ensures that you continue to receive the best results possible from Ryan’s products. You can trust Ryan replacement parts because they are manufactured with the same high precision and quality as the original parts.

Ryan designs and builds its equipment to serve many years in a safe and productive manner. For longest life, use this machine only as directed in the manual, keep it in good repair and follow safety warnings and instructions. You'll always be glad you did.

Jacobsen, a Textron Company

One Bob Cat Lane

Johnson Creek, WI 53038-0469

TABLE OF CONTENTS ..................................... FIGURES ................................................................... PAGE

SAFETY ......................................................................................................................................................... 2

SET-UP ....................................................................................................................................................... 3-5

OPERATION .............................................................................................................................................. 6, 7

SERVICE ................................................................................................................................................... 8, 9

STORAGE/SPECIFICATIONS ..................................................................................................................... 10

PARTS SECTION ......................................................................................................................................... 11

CHASSIS GROUP ............................................. FIGURE 1 ................................................................. 12, 13

ENGINE AND GUARD GROUP ......................... FIGURE 2 ................................................................. 14, 15

FLAIL BLADE REEL .......................................... FIGURE 3 ................................................................. 16, 17

1/8" FIXED BLADE REEL .................................. FIGURE 4 ................................................................. 18, 19

1/16" FIXED BLADE REEL ................................ FIGURE 5 ................................................................. 20, 21

1/32" FIXED BLADE REEL ................................ FIGURE 6 ................................................................. 22, 23

HANDLE ............................................................. FIGURE 7 ................................................................. 24, 25

2-2005

1

2

SAFETY

REN-O-THIN

NOTICE !!!

Unauthorized modifications may present extreme safety hazards to operators and bystanders and could also result in product damage.

Jacobsen, a Textron Company strongly warns against, rejects and disclaims any modifications, add-on accessories or product alterations that are not designed, developed, tested and approved by

Jacobsen, a Textron Company Engineering

Department. Any Jacobsen, a Textron Company product that is altered, modified or changed in any manner not specifically authorized after original manufacture–including the addition of “after-market” accessories or component parts not specifically approved by Jacobsen, a Textron Company–will result in the Jacobsen, a Textron Company Warranty being voided.

Any and all liability for personal injury and/or property damage caused by any unauthorized modifications, add-on accessories or products not approved by

Jacobsen, a Textron Company will be considered the responsibility of the individual(s) or company designing and/or making such changes. Jacobsen, a Textron Company will vigorously pursue full indemnification and costs from any party responsible for such unauthorized post-manufacture modifications and/or accessories should personal injury and/or property damage result.

This symbol means:

ATTENTION!

BECOME ALERT!

Your safety and the safety of others is involved.

Signal word definitions

:

The signal words below are used to identify levels of hazard seriousness. These words appear in this manual and on the safety labels attached to

Jacobsen, a Textron Company machines. For your safety and the safety of others, read and follow the information given with these signal words and/or the symbol shown above.

DANGER indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury.

WARNING indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury.

CAUTION indicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate injury. It may also be used to alert against unsafe practices or property damage.

CAUTION used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, MAY result in property damage.

MODEL NUMBER: This number appears on sales literature, technical manuals and price lists.

SERIAL NUMBER: This number appears only on your mower. It contains the model number followed consecutively by the serial number. Use this number when ordering parts or seeking warranty information.

SET-UP

REN-O-THIN

GENERAL NOTE: FRONT, REAR, RIGHT HAND AND LEFT HAND REFERENCES BELOW

ARE WITH RESPECT TO AN OPERATOR AT THE CONTROLS.

EQUIPMENT AND PARTS INSPECTION

Remove equipment and parts from the packing box and inspect for possible shipping damage. You should have the following items:

-Upper and lower handle.

-Pre-assembled chassis and engine.

-Loose parts bag.

-Reel assembly (if ordered with unit).

REEL INSTALLATION

1.

Remove the belt guards and tilt the unit back to allow access to the underside of the chassis.

Block the unit as required to prevent it from falling accidentally.

2.

Loosen the reel clamps A and pivot down and away from chassis. With the pulley end toward the engine side of unit, set the reel into place against the chassis. Bearing guides B on the reel will provide correct alignment.

3.

Pivot the reel clamps back up over the reel bearings. Install the reel clamp rods C, washers

D and nuts E. Tighten the nuts securely but do not over tighten. Check reel to make sure it rotates freely.

3

SET-UP

PULLEY AND BELT INSTALLATION

1.

Gently tap the woodruff key (from loose parts bag) into the slot on the reel shaft.

2.

Start the two (2) set screws into the reel pulley.

3.

Slide the pulley F, hub side inward, onto the reel shaft. Tap it into position over the woodruff key.

4.

Align the reel pulley with the engine pulley H.

Placing a straight edge across both pulleys will show when the two pulleys are aligned.

5.

Tighten the reel pulley set screws and check the engine pulley set screws to make sure they are also tight.

6.

Place the new belts between the idler pulley and the snubber G on the idler arm, then over the engine and reel pulleys.

HANDLE AND CABLE INSTALLATION

1.

Assemble the upper and lower handle sections using the hardware provided in the loose parts bag.

2.

Mount the handle to the unit by placing the bottom ends of the handle over the pins at the top edge center of the chassis. Secure the handle with hairpins (from loose parts bag).

3.

Connect one end of the spring (from loose parts bag) to the clutch cable and the other end to the arm of the clutch bail on the handle.

4.

Pull the bail back against the handle. The idler pulley should be tight against the reel belts when the bail is against the handle.

5.

Release the bail. The idler pulley should move away from the reel belts and allow the belts to slip on the engine pulley when the bail is released.

6.

Reinstall the belt guards. The belt stop rod K should be positioned outside the belts.

4

REN-O-THIN

SET-UP

REN-O-THIN

WHEEL BEARING LUBRICATION

Using a pressurized lubrication gun and a lithium based lubricant, lubricate the wheel bearings. This procedure should be done at the time of setup and also after every 25 hours of service.

NOTE: During setup, each wheel cavity should be filled.

The cavity is full when lubricant is seen coming out of bearing.

BLADE HEIGHT ADJUSTMENT

Blade height is adjusted by loosening the locking lever L and turning the adjusting knob M to raise or lower the front wheels.

After installing any reel, make the first adjustment on a hard level surface.

Adjust the blades to 1/8" (3 mm) above the surface. Test this setting on a small area, then adjust the blades to turf conditions as required.

Each number on the adjustment decal represents a change of 1/8" (3mm).

If the desired blade position cannot be obtained by adjusting the front wheels, the rear wheels can be adjusted. Mounting the wheels in the top hole lowers the blades and mounting the wheels in the bottom hole raises the blades.

The front axle may be locked in the down position to prevent the floating action if desired.

Install and secure 1/2" screws, washers, lockwashers and nuts in the slots above the axle. This will prevent the axle from moving.

5

OPERATION

REN-O-THIN

6

DO NOT operate this equipment until you have thoroughly read and understand the operation section of this manual.

DO NOT operate equipment without all shields in place.

DO NOT make adjustments or perform any maintenance while the engine is running.

NEVER start or run the engine inside where exhaust fumes can collect. Carbon monoxide present in the exhaust is an odorless and deadly gas.

Gasoline is extremely flammable and highly explosive under certain conditions. Always stop the engine and do not smoke or allow open flames or sparks when refueling. BE SURE to install fuel cap after refueling.

DO NOT

fill containers in a vehicle or on a truck or trailer bed with a plastic liner. Fill containers on the ground away from the vehicle.

When practical, remove gas powered equipment from the truck or trailer and refuel it on the ground. If equipment must be refueled on the truck or trailer, refuel from a portable container rather than a dispenser nozzle.

Keep the dispenser nozzle in contact with the rim of the fuel tank or container opening until fueling is complete. Do not use a nozzle lockopen device.

Any warning decal that becomes illegible should be replaced immediately.

To prevent injuries from thrown blades, NEVER operate the unit with reel blades that are missing, cracked, badly bent or in any type of abnormal condition.

Before operating, check the area and remove any object which may present a safety hazard or damage the equipment.

To prevent injury from rotating blades, NEVER place hands or feet beneath the unit.

This unit is not self propelled by a mechanical drive system. However, under some conditions the reel rotation may cause the unit to move under its own power.

Engage the reel ONLY when you are in the proper operator's position behind the handle.

The clutch bail is designed to be held by the operator to keep the reel belt engaged ONLY during use. DO NOT clamp or fasten the bail to the handle. If the reel is allowed to rotate while the operator is not in the proper operating position, the unit may move on its own. This will create an unsafe situation in which the operator and/or bystanders may be injured.

DAILY PRE-OPERATION CHECK

1. Visually check for loose or damaged parts and fasteners. Repair or replace as needed before unit is placed into operation.

3. Check engine oil level. Add oil if necessary, following the engine manufacturer's recommendations. Refer to engine manual included with literature packet.

2. Check the reel for bent or broken blades; replace as necessary.

4. Fill the fuel tank with the amount and type of fuel recommended by the engine manufacturer.

OPERATION

REN-O-THIN

STARTING THE ENGINE

1.

Turn fuel shut-off valve A to "ON" position.

2.

Push stop switch B to "ON" position.

3.

Move manual choke control lever C to "CHOKE" position.

4.

Move engine throttle control lever D to "FAST" position.

5.

Grasp starter grip and pull slowly until resistance is felt, then pull cord rapidly to start engine.

Repeat if necessary with choke opened slightly.

6.

After engine starts, move choke C to "RUN" position.

7.

Adjust throttle control D on engine as required.

OPERATING TIPS

1. Start the unit in motion BEFORE engaging the reel to prevent unnecessary damage to the turf and to avoid bogging down the engine.

Disengage the reel before stopping forward motion.

2. Make all passes across the turf at a uniform speed.

3. Disengage the reel at the end of each pass and before slowing or stopping to make a turn. This prevents turf damage while turning the unit.

4. If the engine bogs down while going through a thick patch of turf, push down on the handle just enough to raise the reel and allow the engine to return to normal speed.

NOTE: Never cross hard objects or surfaces (such as sidewalks, driveways, stepping stones, etc.) with the reel engaged. Severe blade damage may occur.

REELS AND SUGGESTED USES

1/8" (3 mm) Fixed Blade Reel, Part No. 545440

2" (51 mm) blade spacing is excellent for general dethatching, renovating and breaking up cores.

1/32" (0.8 mm) Fixed Blade Reel, Part No. 547453

3/4" (19 mm) blade spacing is excellent for thatch and grain control on fine bent grasses, vertical slicing, renovating and seed bed preparation.

1/16" (1.6 mm) Fixed Blade Reel, Part No. 547452

Blades can be spaced on 1" (25 mm) or 1 1/2"

(38 mm) centers with the use of spacers between the blades. Use the 1" blade spacing for renovating heavy grass areas or preparing a lawn for re-seeding. Use the 1 1/2" (38 mm) blade spacing for renovating and thinning all coarse stemmed grasses.

Flail Blade Reel, Part No. 544440

1/8" (3 mm) flail blades for thatch control and breaking up soil cores after aerating. This reel is

NOT RECOMMENDED for fine lawns and turf, such as golf course greens.

7

SERVICE

REN-O-THIN

8

When replacement parts are required, use genuine RYAN parts or parts with equivalent characteristics, including type, strength and material. Failure to do so may result in product malfunction and possible injury to the operator and/or bystanders.

BELT REPLACEMENT

Belt tension is maintained by a spring loaded idler, controlled by the clutch bail. No belt tension adjustment is necessary when proper belts are used.

NOTE: A matched pair of belts must be used for correct operation. If one belt needs to be replaced, you MUST replace both belts to assure proper belt tension.

1. Remove belt guards and old belts from unit.

2.

Place the new belts between the idler pulley E and the snubber F on the idler arm and then over the engine and reel pulleys.

3.

Install the belt guards. Make sure the belt stop rod G is outside of the belt.

LUBRICATION

The reel and idler pulley bearings are factory sealed and require no lubrication. Wheel bearings have lubrication fittings and require lubrication with a standard lithium based lubricant after every 25 hours of use.

BELT GUARD ROD ADJUSTMENT

There are two belt guard rods mounted in the belt guard. The long rod H helps to prevent the belts from slipping off the engine pulley. The short rod J (belt stop rod) acts as a belt brake when the clutch bail is released, ensuring that the reel stops quickly.

It is important that these two rods are adjusted correctly. If the belt guard is removed for any reason, make sure the two rods are positioned at the end of their respective slots.

REN-O-THIN

BLADE REPLACEMENT

Fixed Blade Reels - To replace worn or damaged blades or to change to different blade and/or spacer combination.

1.

Remove the entire reel from the chassis.

2.

Remove bearing from end of shaft (opposite the pulley end). Loosen the set screw securing the locking collar. With a small punch, tap the bearing approximately one quarter turn in the opposite direction of the reel rotation. This relieves the cam lock action of the bearing and it can be removed from the shaft.

3.

Hold the shaft to keep it from turning and remove the shaft nut. Remove the blades and spacers from the shaft and replace or rearrange as required.

NOTE: When reassembling the reel, it is important to start and end with a spacer. DO NOT assemble with a blade next to the shaft nut at either end.

Fixed blades must be placed on the shaft in a pattern 60 o

off center from the previous blade.

4.

Re-install the shaft nut and tighten securely to keep the blades from coming loose.

5.

Re-install the reel bearing by exactly reversing the steps taken to remove it.

NOTE: Blades that are worn on one cutting face may be reversed and used again.

Flail Blade reels

Work on only one of the six blade shaft assemblies at a time.

1.

Remove the cotter pin from one end of one of the blade shafts and pull the shaft out.

2.

Replace the blades and other worn parts and reassemble in the proper order while sliding the shaft back into place.

3.

Install a new cotter pin to secure the shaft.

SERVICE

9

STORAGE/SPECIFICATIONS

REN-O-THIN

STORAGE INSTRUCTIONS

To prevent possible explosion or ignition of vaporized fuel, do not store equipment with fuel in tank or carburetor in enclosure with open flame (for example, a furnace or water heater pilot light).

After daily usage of unit.

1. Wash the unit with water after the engine has cooled down.

2. Check the reel blades for damage. Replace any cracked, broken, bent or worn blades.

3. Check the engine oil level and inspect the air cleaner for excessive dirt or any obstructions.

4. Service engine according to engine manufacturer's recommendations. Refer to engine manual for all recommendations.

Before the equipment is put in to storage for any period exceeding 30 days, the following steps should be taken.

1. Drain all fuel from the fuel tank and fuel lines.

2. Start the engine and run until all the fuel is used from the carburetor float bowl and the engine stops.

3.

While the engine is still warm, drain the crankcase oil and replace with the proper weight oil corresponding to the season the equipment will next be used.

4.

Remove the spark plug and squirt a small amount of engine oil into the cylinder. Slowly pull the starter a few times to distribute oil in the cylinder and reinstall the spark plug.

5.

Check the reel for damaged blades and replace as needed.

6.

Lubricate the wheel bearings with a standard lithium based lubricant.

To put the equipment into service after an extended period of storage:

1.

Check for loose parts and tighten if necessary.

2.

Check for damaged blades and replace as necessary.

3.

Fill the fuel tank and then check the engine oil level.

4.

Start the engine and check for fuel leaks. Repair any leaks before operating the unit.

SPECIFICATIONS

Chassis:........... 12 gauge steel, formed and welded

Reduction:............................. 1.33:1 (engine to reel)

Wheelbase:...........14 5/8" (371 mm) at level position

Reel Speed:.............................................. 2700 RPM

Cutting Width:...................................... 18" (457mm)

Cutting Depth:....................................... 7/8" (22mm)

Blade Adjustment:... 1" (25mm) above ground level to 7/8" (22mm) below ground level

Weight (less reel):...........................106 lbs. (48 Kg.)

Engine:

Model..........................................

Model 121432

Type 0120, Trim E1

4 cycle 6.5 H.P. Briggs & Stratton aluminum cylinder with cast iron sleeve

Model GX160

Type K1QX2

4 cycle 5.5 H.P. Honda

Starter......................................... Recoil, on/off switch

Governor....................................

3600 RPM, no load

10

REN-O-THIN

PARTS SECTION

PARTS

SECTION

11

CHASSIS GROUP

FIGURE 1

REN-O-THIN

20

19

38

17

24

30

12

23

25

34

18

16

33

35

37

22

27

14

15

36

31

7

5

21

3

9

2

7

32

13

8

30

29

10

29

32

4

28

11

32

13

29

32

29

28

6

1

12

REN-O-THIN

ITEM PART NO.

DESCRIPTION QTY

ITEM PART NO.

1-1 304636 COTTER PIN, 12 x 1.12 YS 2

1-2 64123-107 BLT-HEX 5/16-18X7/8 2

1-3 64006-02

1-4 64123-31

LCKWSHER-HELICAL 5/16

BOLT-1/2-13X3 HEX

2

2

1-5 64025-02

1-6 64025-30

1-7 64025-19

1-8 517226

NUT-HEX 5/16-18

NUT-HEX 1/2-20 SLOT

NUT-1/2-13 HEX

2

2

4

BRG,SLV .33 .50 .20 IRON 2

1-9 518972.2

1-10 519043

1-11 520875

1-12 520877

CLAMP, REEL

CLAMP, ROD LOWER

BUSHING,FLANGED

ROD,HINGE (PLATED)

1-13 522256

1-14 522375

1-15 522385

1-16 2702114

WASHER,FELT

AXLE PLATING

CHASSIS AY - SERVICE

4

LEVER,LOCKING (PLATING) 1

(INCLUDES ITEMS 17-20)

1

1

2

1

2

2

1-17 520913

1-18 522390

1-19 522394

1-20 4124327

DECAL,INSTRUCTION 1

DECAL,OPERATING INST 1

DECAL,WARNING-OPER 1

LABEL-FRONT, REN-O-THIN1

1-21 64163-55

1-22 64163-73

1-23 545859

WASHER .328X.75X14 GA 2

WSHR-.625IDX1.12DX.062

1

PIVOT AY (PLATED)

(INCLUDES ITEM 24)

1

1-24 316947

1-25 545861

PIN,SPIROL.312 1.250PS

SHIELD AY,TRAILING

(INCLUDES ITEM 26)

2

1

1-26* 548238

1-27 540273

RIVET,.187.625 PA POP

SCREW AY,ADJUSTING

1-28 4124192 WHEEL, 8X2.5 .75BRG SP 4

(INCLUDES ITEM 29)

5

1

1-29 520983

1-30 64229-02

1-31 64163-31

1-32 64163-67

1-33 64163-61

1-34 548190

1-35 64140-3

1-36 2702143

1-37 4124338

1-38 4116761

BALL BEARING

LOCK NUT-NYLON 5/16-18 2

WASHER, 25/64X1X12

WASHER-.516X1X12GA

WSHR .81X.406X16GA

PIN,HAIR.69 1.88.09 YS

COTTER PIN-3/32X3/4

NUT,.38-24 YS FLEXLOCK

*NOT ILLUSTRATED

8

2

8

1

2

1

2

LABEL-FRONT, REN-O-THIN1

LABEL-MADE IN USA 1

CHASSIS GROUP

DESCRIPTION

FIGURE 1

QTY

13

ENGINE AND GUARD GROUP

FIGURE 2

REN-O-THIN

14

REN-O-THIN

ENGINE AND GUARD GROUP

DESCRIPTION

FIGURE 2

QTY

ITEM PART NO.

DESCRIPTION

2-1 64163-55 WASHER .328X.75X14GA

(QTY 1 USED ON B & S)

(QTY 2 USED ON HONDA)

QTY

ITEM PART NO.

2-2 64268-02

2-3 64164-19

2-4 91-0508

2-5 64025-01

2-6 64123-69

2-7 64123-16

2-8 64141-6

2-9 517226

NUT-FL NYLON LCK 5/16-18 4

KEY WOODRUFF.19X.75 #9 1

BOLT,5/16-24 X 1

NUT-1/4-20 HEX

1

2

BOLT-5/16-18X1-1/2 HEX 4

BLT-HEX 3/8-16X1-1/4 1

NUT, 5/16-18

BRG,SLV .33 .50 .20

6

1

2-10 517139 PULLEY

2-11 4133104.7

ARM,DEFLECTOR

2-12 520870

2-13 64163-29

PULLEY,2.75 DIA

WASHER

2-14 520879

2-15 520902

2-16 520941.2

2-17 521813

ROD,ADJUSTING (PLATING)1

ROD,STUD THREADED

GUARD, INNER BELT

1

1

DECAL, WARNING SOUND 1

1

2

1

1

2-18 4133065.7

ARM AY,IDLER

2-19 547440.2

GUARD AY

2-20 4136053

2-21 548052

CABLE AY 1

NUT,.38-16 HX UNITORQ 2

1

1

2-22 64163-31

2-23 64163-19

2-24 524801

2-25 64163-61

WASHER, 25/64X1X12

WSHR-33/64X1-1/4X12GA

1

1

BELT,V-2 MATCHED 30 3/8 1

WSHR .81X.406X16GA

2

2-26 64044-18

2-27 64123-07

2-28 64139-13

2-29 548995

2-30 64123-87

2-31 805875

2-32 524779

2-33 4124757

SCREW-SET 5/16-18 x 5/16 4

SCRW,.25-20.75 YS PS

BLT-WLF 5/16-18X1/2

SPRING,EXTENSION

BOLT-HEX 3/8-16X1-3/4

KEY,.19SQ X 1.75LG PS

PULLEY, 3 INCH DIA.

DECAL, EMBLUM, RYAN

1

1

1

1

1

3

1

15

FLAIL BLADE REEL

FIGURE 3

REN-O-THIN

3

2

5

6

7

9

8

5

1

4

5

2

3

6

10

5

2

7

9

8

16

REN-O-THIN

ITEM PART NO.

DESCRIPTION

3-1 306956

3-2 64163-67

3-3 516897

3-4 517155

COTTER PIN

WASHER-.516X1X12GA

BLADE,FLAIL

SHAFT

3-5 517162

3-6 517163

SPACER, .328 (8mm)

SPACER, .891 (23mm)

3-7 545640 PILLOW BLOCK AY

(INCLUDES ITEMS 8 & 9)

QTY

ITEM PART NO.

6

18

18

6

24

24

2

3-8 548101

3-9 521857

3-10 546377.7

3-11* 544440A

BEARING

COLLAR,BRG LOCKING

SHAFT

REEL AY, FLAIL

(INCLUDES ITEMS 1-10)

1

1

2

2

FLAIL BLADE REEL

DESCRIPTION

FIGURE 3

QTY

* NOT ILLUSTRATED

17

1/8" FIXED BLADE REEL

FIGURE 4

REN-O-THIN

5

2

7

6

8

1

9

3

4

7

2

3

10

9

1

8

6

18

REN-O-THIN

1/8" FIXED BLADE REEL

DESCRIPTION

FIGURE 4

QTY

ITEM PART NO.

DESCRIPTION QTY

ITEM PART NO.

5-1

5-2

5-3

5-4

305134

516898

516904

516905

5-5 517148

5-6 545640

NUT,.88-14 YS HX JAM (KC) 2

BLADE, 1/8" (3.2mm) 10

SPACER, .700 (19.6mm)

SPACER, .900 (23mm)

2

18

SHAFT

PILLOW BLOCK AY

(INCLUDES ITEMS 7 & 8)

1

2

5-7 548101

5-8 521857

5-9 548176

5-10 820484

BEARING

COLLAR,BRG LOCKING

2

2

WSHR,.88 1.50.10 YS FLAT 2

WSHR, FLAT 1.17 1.75 .13 A/R

(USE WASHERS AS REQUIRED SO THAT

THE NUT (ITEM 1) WILL NOT CONTACT

HEX SHAFT (ITEM 5) WHEN TIGHT)

5-11* 545440A REEL AY, .12 BLADE X 2.0

1

(INCLUDES ITEMS 1-10)

* NOT ILLUSTRATED

19

1/16" FIXED BLADE REEL

FIGURE 5

REN-O-THIN

5

2

7

8

6

1

9

3

7

3

4

2

3

10

9

1

8

6

20

REN-O-THIN

1/16" FIXED BLADE REEL

DESCRIPTION

FIGURE 5

QTY

ITEM PART NO.

DESCRIPTION QTY

ITEM PART NO.

5-1

5-2

5-3

5-4

305134

516900

516903

516905

5-5 517148

5-6 545640

NUT,.88-14 YS HX JAM (KC) 2

BLADE,DE-THATCH.075 TH 13

SPACER

SPACER

14

12

SHAFT

PILLOW BLOCK AY

(INCLUDES ITEMS 7 & 8)

1

2

5-7 548101

5-8 521857

5-9 548176

5-10 820484

BEARING

COLLAR,BRG LOCKING

2

2

WSHR,.88 1.50.10 YS FLAT 2

WSHR, FLAT 1.17 1.75 .13 A/R

(USE WASHERS AS REQUIRED SO THAT

THE NUT (ITEM 1) WILL NOT CONTACT

HEX SHAFT (ITEM 5) WHEN TIGHT)

5-11* 547452A REEL AY, .06 BLADE X 1.5

1

(INCLUDES ITEMS 1-10)

* NOT ILLUSTRATED

21

1/32" FIXED BLADE REEL

FIGURE 6

REN-O-THIN

22

7

5

2

7

8

6

1

9

3

4

2

3

10

9

1

8

6

REN-O-THIN

1/32" FIXED BLADE REEL

DESCRIPTION

FIGURE 6

QTY

ITEM PART NO.

DESCRIPTION QTY

ITEM PART NO.

6-1

6-2

6-3

6-4

305134

516901

516903

516904

6-5 517148

6-6 545640

NUT,.88-14 YS HX JAM (KC) 2

BLADE, 1/32" (0.8mm) 25

SPACER, .500 (12.7mm)

SPACER, .700 (19.6mm)

2

24

SHAFT

PILLOW BLOCK AY

(INCLUDES ITEMS 7 & 8)

1

2

6-7 548101

6-8 521857

6-9 548176

6-10 820484

BEARING

COLLAR,BRG LOCKING

2

2

WSHR,.88 1.50.10 YS FLAT 2

WSHR, FLAT 1.17 1.75 .13 A/R

(USE WASHERS AS REQUIRED SO THAT

THE NUT (ITEM 1) WILL NOT CONTACT

HEX SHAFT (ITEM 5) WHEN TIGHT)

6-11* 547453A REEL AY, FIXED 1/32 X 3/4 1

(INCLUDES ITEMS 1-10)

* NOT ILLUSTRATED

23

HANDLE

FIGURE 7

REN-O-THIN

9

11

3

7

10

6

4

2

1

8

12

5

24

REN-O-THIN

ITEM PART NO.

7-1

7-2

7-3

7-4

7-5

7-6

7-7

7-8

7-9

64025-02

64123-07

64163-03

520868.7

520869.7

520912

521744

547441

4136053

7-10 2702144

7-11 64151-17

7-12 800606

DESCRIPTION QTY

ITEM PART NO.

NUT-HEX 5/16-18

BOLT, 1/4-20X1-1/2 HEX

WSHR-.256IDX.62ODX18GA 4

HANDLEBAR, UPPER 1

2

4

HANDLEBAR, LOWER 1

DECAL, REEL CONTROL 1

RELEASE 'S' HOOK

BAIL CONTROL AY

1

1

CABLE AY 1

SPRING,EXTENSION.63 4.3 1

LOCKNUT, HEX 4

CBOLT,.31-18 1.50 YS G5 1

HANDLE

DESCRIPTION

FIGURE 7

QTY

25

Equipment from Jacobsen, a Textron company, is built to exacting standards ensured by

ISO 9001 and ISO 14001 registration at all our manufacturing locations.

A worldwide dealer network and factory-trained technicians backed by Textron Parts Xpress provide reliable, high-quality product support.

BOB-CAT BROUWER BUNTON CUSHMAN RYAN STEINER

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project