Domestic Loop System (DLS)

Domestic Loop System (DLS)
Domestic Loop System (DLS)
Induction loop system for office and home
Manual and instructions for use
This manual is intended to accompany the Ampetronic DLS
(Domestic Loop System). The manual is a detailed guide to
making the most of the DLS system, how to install it and how
to use it. Installing, setting up and using the DLS induction
loop system is very simple and requires no special skills or
experience, however the manual will guide you through the
whole process in detail.
IMPORTANT SAFETY INSTRUCTIONS ............................................... 2
WARRANTY .......................................................................................... 2
DECLARATION OF CONFORMITY ...................................................... 2
1
YOUR AMPETRONIC DLS ............................................................. 3
2
INDUCTION LOOP SYSTEMS – THE BASICS .............................. 5
3
THE AMPETRONIC DLS AMPLIFIER ............................................ 6
4
DLS COMPONENTS....................................................................... 7
5
BEFORE INSTALLING ................................................................... 8
6
INSTALLING THE AMPLIFIER....................................................... 8
7
INSTALLING THE LOOP ................................................................ 9
8
CONNECTING SOUND SOURCES .............................................. 11
9
SETTING UP FOR FIRST USE ..................................................... 13
10 TROUBLESHOOTING .................................................................. 14
11 SYSTEM SPECIFICATION ........................................................... 15
1
IMPORTANT SAFETY INSTRUCTIONS
1.
Read these instructions.
2.
Keep these instructions for future reference.
3.
Heed all warnings.
4.
It is important to follow all instructions.
5.
Do not use this equipment near to water.
6.
Clean only with a dry cloth.
7.
Do not place objects filled with water such as a vase near or on the
equipment.
8.
Do not install the DLS amplifier near to sources of heat such as radiators,
stoves or other equipment producing heat.
9.
Do not place the DLS amplifier in a fully enclosed space; ensure that the
amplifier has ventilation when in use.
10.
This equipment is designed only for servicing by qualified personnel.
Servicing is required when the apparatus has been damaged or exposed to
rain or moisture, or has been dropped.
WARRANTY
This product carries a two year parts and labour guarantee which may be
invalidated if instructions are not followed correctly or if the unit is misused or used
for an unintended purpose.
Refer all enquiries relating to the product guarantees to your reseller or distributor.
DECLARATION OF CONFORMITY
Manufacturer:
Ampetronic Ltd.
Northern Road, Newark, NG24 2ET. United Kingdom.
Declares that:
Ampetronic Domestic Loop Amplifier, type name ‘DLS’
Conforms to the following directives and norms:
Directive 2004/108/EC
EMC: EN61000-6-3:2007 Emission
EN61000-6-1:2007 Immunity
Directive 2006/95/EC
Safety:
EN60065: 2002
22nd November 2007
Leon Pieters, Technical Director
Ampetronic Ltd.
2
1
YOUR AMPETRONIC DLS
Your Ampetronic DLS will deliver excellent sound quality directly to hearing aids or
special receivers, allowing users to hear direct high quality sound from any source, for
example televisions, telephones, computers and doorbells. If you or people you know
have a hearing impairment, the Ampetronic DLS can be very valuable and can
dramatically improve quality of life within your own home or office.
How will the Ampetronic DLS help you?
BE INDEPENDANT
You will be in complete control of the volume that you hear without
affecting others – no more arguments over the TV volume!
BE IN CONTROL
You can combine sounds from many sources, for example television,
computer, telephone and a microphone so they are all at the ideal
volume with no adjustment of hearing aids or sound sources.
HEAR CLEARLY
You can turn off all interfering background noise and hear only the
sounds that you want to hear, improving concentration and reducing
tiredness, and making listening to any sounds much more enjoyable.
BE SAFE
You can make sure that any alert or warning such as a fire alarm or
doorbells can override whatever you are listening to, ensuring you
never miss a phone call, a visitor, or an emergency.
Key features of the Ampetronic DLS
Excellent sound quality World leading
technology used in professional audio
systems around the world - no
compromise in sound quality.
Automatic priority switching for
‘alerts’ An alert input sound will stay off
until an alarm rings or similar sound is
heard, then it will override any other
sound to ensure that you hear the
warning sounds.
Multiple inputs Up to 4 different sound
sources can be used simultaneously
Discrete Designed to be elegant and
discrete for either home or office
environments
Automatic volume control Volume
automatically adjusts, however loud or
quiet the TV programme or phone call –
you do not need to adjust anything.
Simple installation Suitable for
installation by anyone – no experience or
knowledge required.
Design and safety standards
Designed to the highest safety
standards for your piece of mind.
3
1.1
How and where can you use the DLS?
The Ampetronic DLS is suitable for use in the home or office, wherever you might need
to hear entertainment, communications or alarms. The amplifier can be installed in
any indoor environment and used wherever you want to be.
The Ampetronic DLS transmits sound directly to a hearing aid or receiver as safe and
invisible magnetic waves. The sound can be received when the user is within a loop,
which can be very small – as small as a single chair or sofa – or which can be around
a room or area up to 5 x 6m or 30m2 (a larger room or area can be used if a lower
signal strength is acceptable which will depend greatly on your hearing aids or
receiver).
The amplifier can take up to 4 different sound sources simultaneously, from a very
wide range of possible sources, allowing you to fit the DLS system to match your
lifestyle…
1.2
Induction loop systems in public places
Your DLS amplifier is only one form of induction loop system – you can benefit from
this technology outside of your home or office too! You may want to know where you
can get this benefit in public. Typically where an induction loop system is installed for
your use you will see a sign like this…
Where you see the sign you should be able to switch your
hearing aids to the ‘T’ setting (unless they switch automatically)
or use an induction loop receiver. Where you don’t see the
sign, don’t forget to ask why there is no induction loop!
The variation in use of induction loop systems is significant
from country to country so you will get the best information on
where and how they are used by contacting the hard-of-hearing organisation in your
country, by asking your hearing specialist or through an Ampetronic sales agent in
your country.
4
2
INDUCTION LOOP SYSTEMS – THE BASICS
The Ampetronic DLS is an Induction Loop System. Induction loops are an excellent
way to help anyone with a hearing impairment hear an audio communication or
broadcast, both in public and in the home or office. Induction loop systems are often
used in public environments from ticket counters and intercoms through to theatres
and cinemas. In many countries induction loops are already the standard solution for
helping the hard-of-hearing to gain fair access, and can be found installed in most
public environments in the UK and parts of Scandinavia.
An induction loop system consists of four parts:
1
Sound
sources
2
3
Amplifier
Wire loop
4
Hearing aids /
receiver
1.
One or more sound sources – the sounds that you want to listen to directly,
for example your television, hi-fi system, computer, telephone, a microphone,
or alerts such as a doorbell or fire alarm
2.
An induction loop amplifier – a special amplifier that is connected to the
various sound sources and amplifies the sound as an electrical signal into a
loop
3.
A wire loop – a loop connected to the induction loop amplifier which goes
around the area in which you would like to use the system, for example around
the outside edge of your room, or around a small area such as a chair or sofa.
The loop transmits the sound as a completely safe and invisible magnetic field
in the area above the loop.
4.
Receivers, usually hearing aids – a small coil picks up the sounds broadcast
through the loop. Coils – sometimes known as ‘T-coils’ or ‘telecoils’ – are
often found within hearing aids, either with a small switch marked ‘T’ or
automatically switching.
Once an induction loop system has been installed and set-up it should require no
attention, adjustment or maintenance. At any time a user can switch their hearing aids
or use their receivers to hear the sounds being broadcast into the loop system.
5
3
THE AMPETRONIC DLS AMPLIFIER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
14
FEATURE
DESCRIPTION
1.
TONE CONTROL
Tone control, normal response with knob at centre and marker
pointing up. Adjust to give your preferred sound.
2.
VOLUME CONTROL
To adjust volume transmitted by the loop.
3.
SIGNAL INDICATOR
When lit, the input level is high enough to ensure that the loop
will be loud enough. Normally on when sound is present.
4.
HEADPHONE SOCKET
Monitors the signal that is actually broadcast into the loop.
Useful for setting up the loop and fault finding.
5.
POWER SWITCH
To turn power on and off. The Ampetronic DLS can be left on at
all times, or turned off when not used as preferred.
6.
POWER INDICATOR
Green light, on when the unit has power and is turned on.
7.
RUBBER FEET
To isolate the unit from vibration and heat and provide a secure
and stable base in any installation.
8.
LOOP CONNECTOR
Speaker style connector for the two cable ends of the loop.
9.
POWER CONNECTOR
Power connector for the 12V DC power supply provided.
10.
INPUT 1
Audio input with twin RCA connectors (see section !8)
11.
INPUT 2
Audio input with twin RCA connectors (see section !8)
12.
INPUT 3 (ALERT)
SWITCH
Selects line level (right) or microphone (left) for input 3
13.
INPUT 3 (ALERT)
LEVEL ADJUSTER
Adjusts sensitivity of input 3, setting the level at which a noise
will trigger the alert (priority) input
13.
INPUT 3 (ALERT)
Alert input – sounds at this input will override other inputs, and
be turned off when not in use
14.
INPUT 4 LEVEL
ADJUSTER
Adjusts sensitivity of microphone input 4 as required
15.
INPUT 4
(MICROPHONE)
Microphone input for electret style microphone (provided) with
minijack input
6
15
4
(1)
DLS COMPONENTS
The DLS kit contents:
• DLS amplifier and instructions (1)
(2)
• 30m loop cable and cable clips (2)
• 1 x Clip microphone and cable (3)
• 1 x Mini-jack cable (4)
• 1 x RCA cables (5)
• 1 x power supply (6)
(3)
(4)
(5)
(6)
Additional accessories
Available through your local dealer.
• Chair pad (7)
A 40cm square pad to place
under or in a cushion on a chair
or sofa, to create a local field for
one person, often instead of
using the room loop cable.
(7)
• Telephone adaptor (8)
To connect a phone line or
phone network to the DLS unit
• SCART adaptor (9)
To connect a television to the
amplifier using a ‘throughSCART’ connection that does
not affect your existing SCART
connections.
(8)
Phone adaptor
provided separately
• Additional cables and
microphones
7
(9)
5
microphones or the telephone that
you do not want others to be able to
hear.
BEFORE INSTALLING
Before the DLS system is installed
please check that your environment is
suitable and that you have appropriate
receivers or hearing aids as follows.
Both of these problems can be avoided
by using a chair pad accessory instead
of a room loop.
What receivers or hearing aids will
you use?
Background noise
Occasionally poor quality electrical
systems can create interference that
you will hear if you try to use an
induction loop system. Before installing
the DLS, turn on your receiver or turn
your hearing aids to the ‘T’ setting – if
you hear a lot of background noise or
hum then your room may not be
appropriate for an induction loop
system. Ask you supplier for advice if
this happens.
To hear the output from the
Ampetronic DLS you must use a
receiver. For most people this will be
hearing aids, which typically contain a
telecoil or ‘T’ function. Hearing aids
must be switched to the ‘T’ setting –
some hearing aids automatically
switch to the ‘T’ setting, others have a
manual switch. Check with your
hearing advisors or hearing aid
suppliers if you are unsure of how to
use your hearing aids with an
induction loop system.
6
Without hearing aids the user needs to
use a receiver and headphones to
hear the output from the Ampetronic
DLS. The supplier of your Ampetronic
DLS can help you to find a suitable
receiver.
INSTALLING THE
AMPLIFIER
Where will you put the DLS
amplifier?
The DLS amplifier should be placed
somewhere where:
Other loop systems
• cables for each sound source can
reach the amplifier
The DLS loop system will create a
strong signal that you can hear within
the area of the loop. There is also a
much weaker signal that carries up to
10m away from a room loop. This can
occasionally cause a problem if:
• cable for the loop (chair or room loop)
can reach the amplifier
• volume and tone controls can be
adjusted by the user
The DLS amplifier can stand
horizontally or be mounted on a panel
(for example underneath a desk) or on
a wall as shown on the next page.
- there is another ‘room loop’
induction loop system in use within
10m of your room – you may pick
up interference from this loop
system which you can hear in your
room, or you might create
interference in someone else’s
loop.
Installing the amplifier
Find a suitable location for the amplifier
at which there is access to power, to
cables from the sound sources and for
the loop cable.
- you use the system for confidential
or private conversations with
8
The amplifier can either be
freestanding or wall / panel mounted –
see below for wall / panel mounting
instructions.
7
The location for the DLS amplifier
must be indoors and dry. The DLS
amplifier must not be covered by
material of any kind, and must have
some air movement around the case
to prevent heat build up.
Room loop installation
INSTALLING THE LOOP
For moving, standing up or in different
locations within a room.
A room loop is a loop of wire usually
placed around the wall or skirting board
around the edge of the room.
Place the amplifier in its required
location but do not connect the power
lead until installation is complete.
Wall / panel mounting
Included in the DLS amplifier box is a
template for marking out the two screw
holes.
Decide on the location for the DLS
amplifier and use the template to mark
out two screw holes. Put two screws
in place (screw heads should be 68mm diameter). Leave the screw
heads protruding by 8-10mm from the
wall. Hang the DLS amplifier on the
screw heads using the holes on the
bottom of the case.
A wire can also be used around a
smaller area underneath carpet or a
rug. The loop must cover the whole
area in which the user needs to hear
the sound from the DLS induction loop.
A room loop is simple to install but does
require you to be able to run a cable
around your room and fix it safely using
the cable clips provided, or another
fixing method.
9
•
Decide what the area is that needs
to be covered by the cable.
•
Start with one end of the cable at
the DLS amplifier.
•
Run the cable from the cable reel
provided around the edge of the
area that is required to be used.
Typically this will be the edge of a
room.
•
Use cable clips (provided) to
secure the loop cable, or place the
loop cable underneath a rug or
carpet.
•
•
•
cables with a sharp bend in the
end.
The cable should ideally be fitted
at floor or ceiling level, never at
head height. The diagram shows
both options as a green and a red
loop.
•
Cable can run over doorways to
prevent trip hazards, see the red
loop in the diagram.
Chair loop installation
Run the free end of the cable
back to the DLS amplifier.
•
Connect the cable ends to the
amplifier – see the end of this
section.
•
The room loop is now installed.
The Chair
Loop pad is
an optional
accessory.
The pad
comes with
5m of cable
attached to
allow you to
sit anywhere
within the
room, and a
connector for
easy removal
or connection.
Make sure
that the pad
can be placed
under or
behind the chair that needs to be used
and the cable can be run safely from
the chair to the DLS amplifier.
Dealing with excess cable
If there is a large amount of excess
cable (more than half of the reel) then
it needs to be wound carefully or
removed. Please note that the
minimum cable length for the system
is 8m.
The excess wire can be cut
away with scissors or wire
cutters. The end of the cable
needs to have the plastic
sheath removed to expose the metal
ends as shown:
If you can not or do not want to
remove the excess wire, coil the
remaining wire as follows:
•
•
•
Coil the two parallel cables
together, tie, tape or otherwise fix
the coil in place.
Both ends should be connected to
the amplifier as instructed above.
Identify the point of the free cable
that is the end of the useful loop –
fix or hold this temporarily to the
amplifier.
Pull out the remaining cable into a
loop and pull it away from the
amplifier so it forms two parallel
10
•
Place the pad in one of three
places: under the seat cushion;
behind the seat back; or inside a
seat cushion (seat or backrest)
•
Run the connecting cables to the
DLS amplifier.
•
Cover the cable with a rug or other
protection to prevent tripping or
catching the cable.
•
Connect both ends of the loop
cable to the DLS amplifier, see the
end of this section
•
The chair loop is now installed.
8
Connecting the loop to the amplifier
Once the loop has been installed the
two cable ends must be connected to
the loop connector on the DLS
amplifier (shown below).
CONNECTING SOUND
SOURCES
The Ampetronic DLS can accept up to
4 different inputs simultaneously. What
do you want to hear?
The possible sound sources are as
follows for each of the 4 inputs on the
DLS amplifier – work out what you want
to connect before starting the
installation.
First, terminate the cable ends if
required so both cable ends have 515mm of exposed cable:
The connector has
two holes above a
red and a black
switch. When the
switches are
pushed down the
hole is open, when
the switched is
pushed up the
hole is closed and the loop cable will
be clamped in place.
Inputs 1 and 2 (line inputs)
Up to two of the following items can be
connected:
- Television
- HiFi
- Radio
- Computer audio
- iPOD / MP3 player
Connect one end of the cable to the
black terminal of the DLS amplifier:
- Telephone via adaptor (not
provided)
• Push the black terminal of the
loop connector down
• Select the appropriate cable for your
equipment, minijack, RCA or
SCART (optional accessory).
• Put the cable end into the hole
above the black switch
• Connect the two RCA jacks to the
connectors of input 1 or input 2 and
the other end to your equipment.
• Lift up the black switch to capture
the cable in place
Connect the free end of the cable to
the red terminal of the DLS amplifier in
the same way.
Input 3 (alert input)
This input can take any input, but is
reserved for warning sounds, sounds
that will not normally be heard, but
when they occur it is important that they
are heard.
Check that both loop wires are
securely held by the connector on the
DLS amplifier
Typically connected to one of:
- Microphone directed at an alert
sound (e.g. telephone, fire alarm)
- Alert system (e.g. Bellman Visit
Pager systems)
11
• Locate the switch on input 3 on
the rear of the DLS amplifier and
make sure that it is moved to the
left for a microphone, to the right
for a line input.
• If using a microphone, place it as
close as possible to the source of
the alert or warning sound, and
connect the microphone jack to
input 3 of the DLS amplifier.
• If using a line input, set up the
sound source according to
manufacturer’s instructions, and
connect using a minijack cable to
input 3 of the DLS amplifier.
• Check that the alert input sounds
when other inputs are also being
used. Adjust the input level if
required using the rear mounted
level control. Make sure the input
comes on when (and only when)
an alert sound occurs.
Input 4 (microphone input)
This input will accept one microphone
input. This might be used for:
- Room sounds, e.g. speech
- Television or other loudspeaker
• Mount the microphone so that it
can pick up the sounds that you
want to hear.
• Use the adhesive pad to attach to
loudspeakers or any surface:
• Connect the microphone jack to
input 4 of the DLS amplifier.
12
9
control on the rear of the amplifier next
to input 3.
SETTING UP FOR FIRST
USE
• SET UP INPUT 4
Plug the unit into power using the
power cord, and turn the unit on at the
front panel switch. The green light
should come on when there is power.
With a line input (1 or 2) connected and
running with a continuous sound, test
the level of the microphone input (input
4) if used. Adjust the microphone level
on the back panel if required so the
microphone volume is balanced with
the other sound sources.
• SET UP INPUTS 1 & 2
If you are using either of inputs 1 or 2,
turn on one of the connected sound
sources and make sure that it is
producing sound. If there are
adjustments on the sound source (e.g.
on a PC) turn the output levels to
maximum.
• ADJUSTMENTS IN NORMAL
DAY TO DAY USE
The amplifier should now be set
correctly. Gain is automatically
controlled so you should hear the right
volume level whatever you are listening
to, so you should not need to make any
adjustments at all.
The yellow light should come on
permanently or intermittently. If not
then the input is too quiet. Change the
programme material or turn up the
input level until the yellow light is
comes on.
• LISTEN AND SET VOLUME &
TONE
Set up your receivers or hearing aids
to receive the loop signal, switching
hearing aids to the ‘T’ setting.
Sit in the position / positions that you
will use the system in. Set the volume
and tone on the amplifier to give you
comfortable and clear sound.
• SET UP ALERT INPUT 3 IF
REQUIRED
With input (1 or 2) connected and
running with a continuous sound, test
the level of the alert input (input 3) if
used. In the unlikely event that the
alert input does not cut in over the
other sounds when a noise is
produced, increase the level of this
input sound, by moving the
microphone closer to the sound
source, or by adjusting the level
13
10 TROUBLESHOOTING
2. Interference / hum / background
noise in the loop
The Ampetronic DLS should not
require any maintenance or support.
In the event that you have problems,
please consult list of possible
problems below before contacting your
supplier.
• Check hearing aids / receivers set
correctly
• Turn the loop system off and
check to see if background noise
remains. If it does then the noise
may be created by other electrical
systems. Try turning off nearby
appliances to find the source of
interference. Noise may also
come from another nearby loop
system – are there any other loop
systems within 10m of your
system?
• If a microphone is connected to
input 4, turn the level control down
or disconnect the microphone –
does the background noise
remain? If not, reduce the noise
being picked up by the
microphone or reduce the gain
control on input 4.
1. No sound / low volume
• Check that the power light (green)
is on to confirm that the unit has
power.
• Check that there is a sound being
produced by the input source
• With input source making a
sound, the front panel yellow light
should come on permanently or
intermittently. If not your input
level is too low.
• Check that there is a signal in the
loop using headphones in the
headphone jack on the front panel
– if not then there is a problem
with the loop or no input signal.
• Check loop connections – are
both loop ends connected firmly
and are the cable ends properly
terminated with exposed wire in
the contacts?
3. Alert input not working
• Make sure that volume of alert
signal is high – move microphone
as close as possible to the alert
sound source.
• Increase output level as far as
possible from any third party
alerting device.
14
11 SYSTEM SPECIFICATION
Controls and features:
Tone control:
Inputs:
A modified tone control allowing a flat response or bass boost
/ HF cut or HF boost / bass cut, with additional HF boost to
allow compensation for distortion due to metal structures in
surrounding buildings.
1 & 2. Four input Line level phono connector, fixed gain,
allowing two stereo inputs.
3. One independent mic/line input; Priority
Microphone/Line control which is switchable between Mic or
Line level. VOX switching is permanently enabled on this
channel.
Outputs:
Headphone monitoring output via front panel with stereo
3.5mm jack.
4. One independent Mic input, gain control – rear panel,
allowing adjustment to the correct level.
Output connection: Loop, finger operated quick connect
output connector.
Current: >2.4ARMS into 1!.
Voltage: >3.2VRMS.
DC Power input, 2.1mm, centre positive.
Controls:
Loop resistance: 0.3! to 1.0! resistive or 1.5! maximum
reactive impedance at 1.6 kHz.
Connection: Finger operated speaker type connector.
Tone control: Independent front panel control allowing
frequency response adjustment for differing installation
variations.
Loop volume: Independent front panel control allowing
Loop output current (volume) adjustment.
Area coverage:
2
Input specifications:
>30m coverage to requirements of IEC60118-4, or use with
supplied special loop pad.
Note that the amplifier can drive loops far in excess of this
size if the full performance of IEC60118-4 is not required by
the end user.
Microphone input 4:
Environmental:
Connector: 3.5mm mono jack socket.
One independent microphone input suitable for use with an
unbalanced electret microphone.
Input impedance: 8k!.
Phantom voltage: 6V via 10k! source.
Input sensitivity: -60dBu for maximum output
Ambient temperature: -10 C to 45 C.
Relative humidity: 20% to 90%
IP rating: IP20
Ventilation: Ensure adequate ventilation is provided for the
Domestic unit as the unit becomes warm during operation.
Mounting: Unit may be mounted horizontally or vertically.
Rubber ‘bump on’ feet are fitted allowing free standing.
Two screw slot fittings allowing wall mounting of the unit are
incorporated.
Microphone input 4 gain control – rear panel.
o
Switchable Line / Mic input 3:
Line input selected:
o
Physical:
Connector: 3.5mm mono jack socket.
Slide switch selection.
Input impedance: 820k!.
Input sensitivity: Line input selected: -20dBu for maximum
output after VOX enabled at -12dBu
Weight: 305g. Length: 133mm. Width: 72mm. Height: 40mm
Power requirements:
12V DC @ 1.0A max.
Fuse fitted to PCB, type T 1.6A L
Green LED Power indicator.
Microphone input selected:
Levels as per microphone input 4.
AC Power adaptor (Powerpax 85-2943):
Input: 100Vac – 240Vav 47 - 63Hz.
Power consumption: Standard load = 10W (1.0ARMS pink
noise output, as per IEC60065).
Power consumption: Quiescent = 3.0W.
Output: 12Vdc at 1.25A max.
Line level inputs 1 and 2:
4-way phono input connector. Fixed gain.
Input sensitivity: -10dBu for maximum output.
Overload: >30dBu
Compression:
AC Power adaptor UK (Powerpax 85-2915):
Input 230Vac, 45 – 65 Hz.
Power consumption: standard load = 10W (1.0ARMS pink noise
output, as per IEC60065).
Power consumption: Quiescent = 2.0W.
Output: 12Vdc at 1.0A max.
Compression Dynamic range: >36dB before overload.
(Typically 40dB).
Compression indication via amber signal LED.
Efficiency: ± 1 dB across 40dB dynamic range.
Attack and decay times optimised for speech.
Attack time: Less than 5ms; Decay time: Less than 2 seconds.
Directives and Norms:
Frequency response:
Directive 2004/108/EC
EMC:
EN61000-6-3:2007 Emission
EN61000-6-1:2007 Immunity
Directive 2006/95/EC
Safety: EN60065: 2002
80 Hz to 6.3 kHz ± 1.5dB into 1! load at low level, measured
as loop current with no Metal Loss correction.
15
Manufactured by Ampetronic Ltd.
Ampetronic
Northern Road
Newark
NG24 2ET
United Kingdom
+44 (0) 1636 610062 telephone
+44 (0) 1636 610063 fax
www.ampetronic.com
Supplied by:
Contact your supplier for questions and support
16
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising