LevelOne WAP-1001 11g Wireless Outdoor Access Point

LevelOne WAP-1001 11g Wireless Outdoor Access Point
LevelOne
WAP-1001
11g Outdoor Wireless AP/Bridge
User Manual
Ver.1.02-0917
1
FCC Notice
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed
and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
—Consult the dealer or an experienced radio/wireless technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
The antenna(s) used for this transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
The manufacture is not responsible for any radio or wireless interference
caused by unauthorized modifications to this equipment. Such modifications
could void the user’s authority to operate the equipment.
2
The Wireless Technology
Standard
The Wireless Access Point utilizes the 802.11b and the 802.11g standards. The
IEEE 802.11g standard is an extension of the 802.11b standard. It increases
the data rate up to 54 Mbps (108Mbps in Super G mode) within the 2.4GHz
band, utilizing OFDM technology. This means that in most environments, within
the specified range of this device, you will be able to transfer large files quickly
or even watch a movie in MPEG format you’re your network without noticeable
delays. This technology works by transmitting high-speed digital data over a
radio wave utilizing OFDM (Orthogonal Frequency Division Multiplexing)
technology. OFDM works by splitting the radio signal into multiple smaller
sub-signals that are then transmitted simultaneously at different frequencies to
the receiver. OFDM reduces the amount of cross talk (interference) in signal
transmissions. The AP will automatically sense the best possible connection
speed to ensure the greatest speed and range possible. 802.11g offers the
most advanced network security features available today, including: WEP,WPA,
TKIP, AES and Pre-Shared Key mode.
Planning Your Wireless Network
Network Topology
A wireless network is a group of computers, each equipped with one wireless
adapter. Computers in a wireless network must be configured to share the
same radio channel. Several PCs equipped with wireless cards or adapters can
communicate with one another to form an ad-hoc network. The wireless
adapters also provide users access to a wired network when using an access
point or wireless router. An integrated wireless and wired network is called an
infrastructure network. Each wireless PC in an infrastructure network can talk
to any computer in a wired network infrastructure via the access point or
wireless router. An infrastructure configuration extends the accessibility of a
wireless PC to a wired network, and may double the effective wireless
transmission range for two wireless adapter PCs. Since an access point is able
to forward data within a network, the effective transmission range in an
infrastructure network may be doubled.
3
Roaming
Infrastructure mode also supports roaming capabilities for mobile users.
Roaming means that you can move your wireless PC within your network and
the access points will pick up the wireless PC's signal, providing that they both
share the same channel and SSID. Before enabling you consider roaming,
choose a feasible radio channel and optimum access point position. Proper
access point positioning combined with a clear radio signal will greatly enhance
performance.
Network Layout
The AP Access Point has been designed for use with 802.11g and 802.11b
products. With 802.11g products communicating with the 802.11b standard,
products using these standards can communicate with each other. The Access
point is compatible with 802.11g and 802.11b adapters, such at the PC Cards
for your laptop computers, PCI Card for your desktop PC, and USB Adapters for
when you want to enjoy USB connectivity. These wireless products can also
communicate with a 802.11g or 802.11b wireless Print Server. When you wish
to connect your wired network with your wireless network, the Access Point’s
network port can be used to connect to any of switches or routers.
Installation Considerations
The AP lets you access your network, using a wireless connection, from
virtually anywhere within its operating range. Keep in mind, however, that the
number, thickness and location of walls, ceilings, or other objects that the
wireless signals must pass through, may limit the range. Typical ranges vary
depending on the types of materials and background RF (radio frequency)
noise in your home or business. The key to maximizing wireless range is to
follow these basic guidelines:
z
z
z
Keep your product away (at least 3-6 feet or 1-2 meters) from electrical
devices or appliances that generate RF noise.
Keep the number of walls and ceilings between the AP and other network
devices to a minimum - each wall or ceiling can reduce your AP’s range
from 3-90 feet (1-30 meters.) Position your devices so that the number of
walls or ceilings is minimized.
Be aware of the direct line between network devices. A wall that is 1.5 feet
thick(0.5 meters), at a 45-degree angle appears to be almost 3 feet (1
meter) thick. At a 2-degree angle it looks over 42 feet (14 meters) thick!
Position devices so that the signal will travel straight through a wall or
4
z
ceiling (instead of at an angle) for better reception.
Building materials can impede the wireless signal - a solid metal door or
aluminum studs may have a negative effect on range. Try to position
wireless devices and computers with wireless adapters so that the signal
passes through drywall or open doorways and not other materials.
5
Installation Diagram
Device Photo
Bracket Installation
Combine the accessories in
order.
Bracket installation complete.
6
POE Injector Installation
Connection instruction
Wrong POE injector placement.
When placing WAP-1001 in outdoor environment, there is an Ethernet cable
connecting WAP-1001 and POE Injector. If place the POE injector on the ground
like the photo shown, rain or dust might leak via the Ethernet cable and
permeate into the POE injector. This will result in power failure.
7
Correct POE injector placement
In order to avoid the problem mentioned above, please place the POE injector
higher than the Ethernet cable, so that the raindrop will not permeate the POE
injector.
Attention:
z
The cable distance between the Router and PC/hub/Switch should
not exceed 100 meters.
z
Make sure the wiring is correct. In 10Mbps operation, Category
3/4/5 cable can be used for connection. To reliably operate your
network at 100Mbps, you must use Category 5 cable, or better
Data Grade.
8
Unplug the Ethernet cable attached to WAP-1001
WAP-1001 conforms to IP66 water approval standard. The connector of
WAP-1001 is special designed to avoid the possible leakage. Therefore the user
might find it is difficult to unplug. Please prepare a small flat screwdriver and
follow the instruction below:
1.The connector is located inside the WAP-1001 as below.
2.Insert the flat screwdriver and make sure that RJ45 connector is compressed.
9
3.At this moment, the screwdriver should compressed RJ45 connector like the
picture below inside the WAP-1001.
4.Hold the screwdriver and the Ethernet cable, and pull out simultaneously.
10
AP Configuration Using Locator
While entering the Locator utility, the Locator will automatically search the
available WAP-1001 on the same network. Locator will show the Device Name,
Device Type, IP Address, Ethernet MAC Address and Firmware Version in first
page. Before start using Locator, make sure you disable personal firewall
installed in you PC. (Ex. Windows XP personal firewall)
If you have 2 Fast Ethernet Adapter or more, you can choose enable one Fast
Ethernet Adapter for enter with Locator utility.
AP Configuration Using Web User Interface
Before Setup...
™ Verify the IP address setting
You need to configure your PC’s network settings to obtain an IP address.
Computer use IP addresses to communicate with each other across a network,
such as the Internet.
1. From the taskbar, click the Start button, select Settings > Control
Panel. From there, double-click the Network connections icon.
2. Right click the Local Area Connection icon Properties; select the
TCP/IP line for the applicable Ethernet adapter. Then, click the
Properties button.
3. Click the IP Address tab page, select USE the following IP
address, type 192.168.1.X (X can be from 1 to 254,but
192.168.1.20 is for WAP-1001 already, please avoid the confliction)
in the IP Address field and 255.255.0.0 in the Subnet Mask field,
then click OK button.
Start Setup by Browser...
1.
After getting the correct connection, start the web browser (make
sure you disable the proxy) and type 192.168.1.20 (The default IP
of outdoor AP ip Address) in the Address field. Press Enter.
11
2.
3.
Enter the factory default User name and Password fields:
User Name: Admin
Password: (leave blank)
then click OK button.
You will enter the Utility homepage.
Start Setup by Locator...
1.
You just need to click on the “Web” icon in Locator main page. The
Locator will launch a default browser for you and lead you into web UI
directly
12
Wireless Configuration - AP Mode
System Status–
<System Summary>
The first page appears in main page will show “System Status -> System
Summary” automatically, you can find detail system configuration in this page
including
z
z
z
System Information – This will display system name and both Ethernet
MAC address and Wireless MAC address. Current country setting and
firmware version will also be available here.
Current IP Settings – This section show current IP address setting
including IP address, Subnet Mask, Default Gateway and DHCP status.
Current Wireless Settings – This area show current wireless setting
including operation mode, wireless mode, SSID, channel and security
setting.
13
<Wireless Station List>
The first page appears in main page will show “System Status -> Wireless
Station List” automatically, this page can help user identify current devices
who already associated to the AP. You can also click on the MAC address
column then the system will show the detail technical information for each
wireless station.
Clicking MAC address hyperlink of desired remote devices, system will show a
Statistics page for you to monitor the information of the remote link.
Values on this page are automatically refreshed every minute. You may
manually press the refresh button of browser to get the updated data more
frequent. As RF signal strength is more critical for outdoor deployment
purpose, RSSI bar is refreshed every 2 seconds.
Note: Due to frequent refresh of Statistics page, it is strongly
recommended that you close this page when performing network performance
tests.
14
Field
Description
RSSI
Displays the strength of the received signal in dBm (the
remote devices received signal strength). Refresh every 2
seconds.
RSSI of ACK
Displays the strength of the ACK signal from far end in
dBm (the local devices received signal strength). Refresh
every 2 seconds.
MSDU
Maximum service data unit. Displays the number of
packets sent and received by the remote devices.
Data / Management Packets can be data, management or control. Displays the
/ Control
number of packets sent and received for each.
Multicast
Displays the number of multicast frames.
Data Rate
Displays the receive and transmit data rate in Mbps.
Receive Errors
Displays the number of receive errors.
Discarded Frames
Displays the number of receive discarded frames.
Duplicate Frames
Displays the number of receive duplicate frames.
CRC Errors
Displays the number of receive CRC errors.
Decrypt Errors
Displays the number of receive description errors.
PHY Errors
Displays the number of receive PHY errors.
DMA Errors
Displays the number of receive DMA errors.
Transmit Errors
Displays the number of transmit errors.
Discarded Frames
Displays the number of transmit discarded frames.
Excessive Retries
Displays the number of transmit excessive retries.
DMA Errors
Displays the number of transmit DMA errors.
15
The page below describes the detail connection information with each station.
You can get all information needed right here.
System Configuration –
Now you can start to configure the system. In System Properties page, you
can config
z
Device Name – You may assign any name to the Access Point.
Memorable, Unique names are helpful especially if you are employing
multiple access points on the same network. The device name needs to be
less than 32 characters. After verify the name you input and click “Apply”
to save the setting.
z
Operation Mode - The default operation mode is Access Point, this
connects your wireless PCs and devices to a wired network. In most cases,
no change is necessary. You can switch operation mode to Wireless Client
or Repeater or Bridge mode depends on your application. Wireless Client
mode can allow AP act as a client within its range. Your Ethernet devices
behind the AP can connect to remote AP. Repeater is able to talk with one
remote access point within its range and retransmit its signal. Choose
repeater mode if you want to extend the range of your original AP. Wireless
Bridge (WDS) can allow Bridge point to point or point to multi-point
16
network architecture, In order to establish the wireless link between bridge
radios, the MAC address of remotes bridge(s) need to be registered in the
address table. Type the MAC address with format xx:xx:xx:xx:xx:xx (x is
the hexadecimal digit) and use “Apply” and “Clear” button to edit the
address table. A Master Bridge Radio may accommodate up to 8 remote
MAC addresses.
Administration –
In the administration page, you can modify “Administrator Name” and
“Password”. Changing the sign-on user name and password is as easy as
typing the string you wish in the column. Then, type the password into second
column to confirm. Click “Apply” to finish the procedure. Be sure you noted
the modification before apply all changes.
17
IP Settings –
IP Setting page can configure system IP address. Default IP address is
192.168.1.20 and Subnet Mask is 255.255.0.0. You can manually input IP
address setting or get an IP from a DHCP server.
z
z
z
z
IP Network Setting – Here you can choose to get IP from a DHCP server
or specify IP address manually. Choose to obtain an IP address from DHCP
server if your environment or ISP provide DHCP server. Otherwise, you can
manually setup IP address.
IP Address – The IP address need to be unique to your network. We
would like to recommend you stay with default IP address 192.168.x.x.
This is private address and should work well with your original
environment.
IP Subnet Mask – The Subnet Mask must be the same as that set on
your Ethernet network.
Default Gateway – If you have assigned a static IP address to the
Access Point, then enter the IP address of your network’s Gateway, such as
a router, in the Gateway field. If your network does not have a Gateway,
then leave this field blank.
18
Wireless Network At Wireless Network page can set “SSID” / “Wireless Mode” and “Channel”.
AP supports not only standard 11b/g but also 108M SuperG. (Note: 108 M
SuperG only works with Atheros® based 11a/g solution)
z
z
z
z
Wireless Network Name (SSID) - The SSID is the unique name shared
among all points in a wireless network. The SSID must be identical for all
points in the wireless network. It is case-sensitive and must not exceed 32
alphanumeric characters, which may be any keyboard character. Make
sure this setting is the same for all points in your wireless network. For
added security, you should change the SSID from the default name
Generic, to a unique name.
Suppressed SSID – This option can hide the SSID not available from site
survey tool. Enable this function only if you do not want the Access Point to
be found by others.
Wireless Mode – Default setting is “2.4GHz 54Mbps (802.11g)”. This
will support all 802.11b/g clients connect to the AP. You can choose
“2.4GHz 11Mbps (802.11b)” in wireless mode column if your
environment only have 802.11b clients. The final selection “2.4GHz
108Mbps (802.11 SuperG Static)” supports high speed 108Mbps
SuperG function. In order to support SuperG 108M transmission, all
wireless clients will need to be Atheros® solution.
Channel / Frequency – Select the appropriate channel from the list
provided to correspond with your network settings. All points in your
19
z
wireless network must use the same channel in order to function correctly.
The default setting is “SmartSelect” means the system will pick best
channel for you automatically. Stay with default setting if you do not have
special request on channel selection.
Stations Separation – Default setting is “Disable”. This option can
disallow the client devices connected to this AP could not access each
other.
Wireless Security The wireless security settings configure the security of your wireless network.
There are three wireless security mode options supported by the Access Point:
WEP, WPA-PSK and WPA. (WPA stands for Wi-Fi Protected Access, which is a
security standard stronger than WEP encryption. WEP stands for Wired
Equivalent Privacy.)
In Wireless Security page, you can configure the AP to work with No Security,
WEP, WPA-PSK and WPA security mode. Once you setup the AP to work in
security mode, all wireless stations will also need to have corresponding
settings. System default setting is “No Security”.
20
WEP is a basic encryption method, which is not as secure as WPA. To use WEP,
you will need to select a default transmit key and a level of WEP encryption,
z
z
z
Authentication type – Select “Open System” to communicate the key
across the network. Select “Share Key” to limit communication to only
those devices that share the same WEP settings.
Shared keys input type – Select HEX or ASCII depends on your
preference
Key table – You can input 4 different WEP encryption keys into the table
and by choosing the radio button to decide which one is valid now. The AP
supports 64, 128 and 152bit key length. The longer key we choose usually
means the encryption is stronger.
After all changes are made, be sure to click on “Apply” to make sure all
changes are saved into system.
21
WPA-PSK stands for Wi-Fi Protected Access – Pre-Shared Key. WPA-PSK is
design for home users who do not have RADIUS server in their network
environment. WPA can provide better security level than WEP without difficult
setting procedure.
z
z
z
PassPhrase - Enter a WPA-PSK Shared Key of 8-63 characters. The
Shared Key should be also applying the clients work in the same wireless
network.
Cipher Type – WPA-PSK gives you two encryption methods, TKIP and
AES, with dynamic encryption keys. Select the type of algorithm, TKIP or
AES.
Group Key Renewal period - Enter a number of seconds which instructs
the Access point how often it should change the encryption keys. Usually
the security level will be higher if you set the period shorter to change
encryption keys more often. Default value is 1800 seconds, set 0 in Group
Key Renewal period to disable key renewal.
Remember to click on “Apply” to make sure all changes are made before
leaving this page.
22
WPA option features WPA used in coordination with a RADIUS server. (This
should only be used when a RADIUS server is connected to the Access Point.)
z
z
z
z
z
RADIUS Server – Here enter the IP address of your RADIUS server.
RADIUS Port – Port number for RADIUS service, default value is 1812
RADIUS Secret – RADIUS secret is the key shared between Access Point
and RADIUS server.
Cipher Type – WPA gives you two encryption methods, TKIP and AES,
with dynamic encryption keys. Select the type of algorithm, TKIP or AES.
Group Key Update Interval – This column indicate how often should
the Access Point change the encryption key.
23
Wireless Advance Settings The page below can help users to configure advanced wireless setting. Before
making any changes at this page, please check your wireless settings on other
system as well, as these changes will alter the effectiveness of the Access Point.
In most cases, these settings do not need to be changed.
z
z
z
z
z
z
Data Rate – In data rate column you can select all bit rate supported in
current operation mode. Default value is “best” means the system will
automatically adjust the connection speed dynamically according to your
current link status.
Transmit Power – You can adjust the RF output power by selecting
Full/Half (-3dB) / Quarter (-6dB) / Eighth (-9dB) / Minimum. To change
transmit power may decrease your wireless signal coverage.
Beacon Interval (20-1000) – This value indicates the frequency
interval of the beacon. A beacon is a packet broadcast by the Access Point
to keep the network synchronized. A beacon includes the wireless LAN
service area, the AP address, the Broadcast destination address, a time
stamp, Delivery Traffic Indicator Maps, and the Traffic Indicator Message
(TIM).
Data Beacon Rate (DTIM) (1-16384) – This value indicated how often
the Access Point sends out a Delivery Traffic Indication Message. Lower
settings result in more efficient networking, while preventing your PC from
dropping into power-saving sleep mode. Higher settings allow your PC to
enter sleep mode, thus saving power, but interferes with wireless
transmissions.
Fragment Length (256-2346) – This specifies the maximum size a
data packet will be before splitting and creating a new packet and should
remain at its default setting of 2,346. A smaller setting means smaller
packets, which will create more packets for each transmission. If you have
decreased this value and experience high packet error rates, you can
increase it again, but it will likely decrease overall network performance.
Only minor modifications of this value are recommended.
RTS/CTS Threshold (256-2346) – This setting determines how larget
a packet can be before the Access Point coordinates transmission and
reception to ensure efficient communication. This value should remain at
its default setting of 2,346. Should you encounter inconsistent data flow,
only minor modifications are recommended.
24
z
z
z
z
Allow 2.4GHz 54Mbps Stations Only – Default setting is “Disable”.
Select “Enable” all of your wireless clients are 802.11g mode, if you select
“Disable” using both 802.11b and 802.11g wireless clients.
Short Preamble – Preambles are a sequence of binary bits that help the
receivers synchronize and ready for receipt of a data transmission. Some
older wireless systems like 802.11b implementation use shorter preambles.
If you are having difficulty connecting to an older 802.11b device, try to
enable short preamble.
Protection Mode – Protection Mode should remain default value (Auto)
unless you are having severe problems with your 11g Wireless LAN
products not being able to transmit to the Access Point in an environment
with heavy 802.11b traffic. To enable this function boosts the Access
Point’s ability to catch all 11g Wireless transmissions but will severely
decrease performance.
Distance (1-30) – Setup “Distance” according to the longest link
distance between the point to point or point to multi-point in the network.
The input needs to be greater than or equal to the real distance. The range
can be from 1KM to 30KM for normal mode and 1KM to 15 KM in Super
mode.
Remember to click on “Apply” to make sure all changes are made before
leaving this page.
25
Changing SNMP Settings
Under System Configuration, click SNMP to display and change settings for the
Simple Network Management Protocol.
To communicate with the access point, the SNMP agent must first be enabled
and the Network Management Station must submit a valid community string for
authentication. Select SNMP Enable and enter data into the fields as described
below. When you are finished, click “Apply”
Setting
Description
SNMP
Enables or disables SNMP.
Contact
Sets the location string that describes the system location.
Maximum length is 255 characters.
Community
Name (Read
Only)
Specifies a community string with read-only access.
Authorized management stations are able to retrieve MIB
objects. Maximum length is 32 characters.
Community
Specifies a community string with read-write access.
Name (Read
Write)
Authorized management stations are able to both retrieve
and modify MIB objects. Maximum length is 32 characters.
Trap
Enter the IP address of the trap manager that will receive
these messages.
Destination
IP Address
Trap
Destination
Enter the community name of the trap manager that will
receive these messages.
Community
Name
26
MAC Filtering
As an additional layer of security, MAC Filtering allows you to block network
access of specified stations through the access point.
Enable MAC Filtering
You can click the Checkbox MAC Filtering to Enable MAC Filtering.
MAC Filtering Rule
•
•
Select Allow only station in list to filter any MAC address that NOT
listed in the MAC Filtering Table
Select Allow any station unless in list to filter any MAC address that
listed in the MAC Filtering Table
Add MAC Address
You can input MAC address and click Add to add MAC address into the MAC
Filtering Table.
MAC Filtering Table
This lists any wireless stations you have entered. If you have not entered any
wireless stations this list will be empty.
To delete an existing entry, select it and then click the Delete button.
27
Backup/Restore Setting / Firmware Upgrade and Reboot In Management section, you can Backup/Restore Setting, Firmware
Upgrade and Reboot the system in following pages.
z
z
z
Backup the current settings to a file – Click on the “Backup” button,
system will prompt you where to save the backup file. You can choose the
directory to save your configuration file.
Restore settings from a backup file – Here you can restore the
configuration file from where you previous saved.
Restore factory default setting – Be very carefully before restore
system back to default since you will lose all current settings immediately.
If you act the function, the ip address will restore the establishing value
situation.
192.168.1.20 in the IP Address field and 255.255.255.0 in the
Subnet Mask field.
28
Firmware Upgrade – Enter the location of the firmware upgrade file in the
file path field, or click the “Browse” button to find the firmware upgrade file.
Then click on the “Upgrade” button, and follow the on-screen instructions.
The whole firmware upgrade process will take around 60 seconds. Before
upgrade, make sure you are using correct version. Please check with your
technical support service if new firmware available.
29
Reboot – Click on “Reboot” button to restart Access Point.
30
Wireless Configuration – Wireless Bridge (WDS)
Mode (Point to Point & Point to Multi-Point)
Wireless Bridge is WDS (Wireless Distribution System) operation as defined by
the IEEE802.11 standard has been made available. In IEEE 802.11 terminology
a "Distribution System" is system that Interconnects, so-called, Basic Service
Sets (BSS). A BSS is best compared to a "Cell", driven by a single Access Point
(one of those circles in the diagram below). So a "Distribution System" connects
cells in order to build a premise wide network which allows users of mobile
equipment to roam and stay connected to the available network resources.
Wireless Bridge (WDS) is used for wirelessly connect Access Points, and in
doing so extend a wired infrastructure to locations where cabling is not possible
or inefficient to implement. (Be sure you understand the purpose of WDS mode
before proceed configuration.)
The Wireless Bridge (WDS) mode is coexisting with Wireless Bridge (WDS)
mode in this AP, therefore, you can support regular wireless stations or WDS
link. In the “WDS Link Settings”, check box and switch the “Mode” to
“Enable”. Then you are able to fill in MAC Address of each WDS link Settings.
31
Considerations before installation –
z
z
z
Loop Prevention – Be careful to plan you WDS connections, prevent
your wireless network topology to have loop. Once loop shows up, you
network traffic will become unstable.
Performance – The system can support up to 8 WDS links. But all links
and wireless stations that operate at the same time will all share single
radio bandwidth. (Ex. 11g have 54Mbps bandwidth)
Latency – In the chain topology configuration, if the chain becomes very
long, end-to-end latency issue may come in play. We suggest the WDS link
topology planning should not exceed 2 hops in chain configuration.
WDS Security Settings–
WDS now only supports limit wireless security protocol and will have full
dependency with Access Point mode security settings. Here lists 4 different AP
security settings below:
z
z
z
No Security – Both Point to Point and Point to Multi-Point traffic transmit
without encryption
WEP – Both Point to Point and Point to Multi-Point traffic are encrypted by
the same WEP key
WPA-PSK – The Point to Point and Point to Multi-Point work in WPA-PSK
(TKIP) mode and WPA-PSK (AES) mode
32
Wireless Configuration – Wireless Client Mode
AP can also work as an Ethernet client bridge to connect up to 16 Ethernet
device into wireless network. In order to setup the AP to work in Ethernet
bridge mode, you need to choose “Wireless Client” mode and click “Apply”
at System Properties page. After need to reboot the AP to make sure the AP
work in client mode.
After the system reboot is done, you can see the page below. System Status
page show the AP is now working in Wireless Client mode.
33
Connection Status z
z
z
z
z
z
z
z
z
z
z
z
z
Connection – This column show current connection status. If AP already
connect to an Access Point or station, here will show the MAC address of
the associated Access Point or station. Otherwise, connection column will
show “N/A” which means no connection to any Access Point or station.
Network Type – Here indicates the Access Point works in AP mode or
Client mode (Infrastructure mode / Ad Hoc mode)
SSID – SSID column displays current SSID assigned to the AP
BSSID – This column displays the MAC address of the connected device.
Wireless Mode – Here show the Access Point current work in either 11b
or 11g mode
Current Channel – This column indicates the radio channel currently in
use.
Security – Here indicates AP security settings in client mode. Should be
either “Disabled”, “WEP” or ‘WPA-PSK”.
Rx Data Rate(Mbps) –show the current Rx Data rate status
Tx Data Rate(Mbps) –show the current Tx Data rate status
Current noise level –This column shows current link quality with AP by
noise level in 0 to -96 dBm scale.
Signal strength – This column shows current link quality with AP by
signal strength in 0 to -96 dBm scale.
Activity (Packets Rx) –show the current Rx packets
Activity (Packets Tx) –show the current Rx packets
34
Wireless Network z Network Mode – You can set the wireless client into 2 different modes by
clicking radio button. Wireless Client (Infrastructure) act as an AP client
while Ad-hoc can support peer to peer network. Both Infrastructure and
Ad-hoc can support up to 108M SuperG transmission.
z Wireless Mode - Default setting is “2.4GHz 54Mbps (802.11g)”. This
will support all 802.11b/g clients connect to the AP. You can choose
“2.4GHz 11Mbps (802.11b)” in wireless mode column if your
environment only have 802.11b clients. The final selection “2.4GHz
108Mbps (802.11 SuperG)” supports high speed 108Mbps SuperG
function. In order to support SuperG 108M transmission, all wireless clients
will need to be Atheros ® solution.
P
z
P
SSID - The SSID is the unique name shared among all points in a wireless
network. The SSID must be identical for all points in the wireless network.
It is case-sensitive and must not exceed 32 alphanumeric characters,
which may be any keyboard character. You can choose “Attach to any
available SSID”; system will determine the Access Point currently
available and establish connection with that Access Point. If you already
understand your wireless environment well, you can type in the SSID in
“Specify the static SSID” manually.
At Wireless Network page you can find a “Site Survey” button as shown above.
You can easily click on the “Site Survey” to find all wireless networks available
in your current environment.
35
The Site Survey page can help you identify all the APs currently working in your
environment. Just easily click on the BSSID column, the system will join you to
the SSID you specify. In the Site Survey page you can also see the details of all
SSID currently available.
After you determine which AP (SSID) to join, you can click on the BSSID column
your want to choose. The system will automatically join the SSID you specified
after reboot.
36
Wireless Security –
WEP is a basic encryption method, which is not as secure as WPA. To use WEP
as a client, you will need to input a transmit key and a level of WEP encryption
exactly the same as the Access Point.
z
z
Shared keys input type – Select HEX or ASCII depends on your
preference
Key table – You can input 4 different WEP encryption keys into the table
and by choosing the radio button to decide which one is valid now. The AP
supports 64, 128 and 152bit key length. The longer key we choose usually
means the encryption is stronger.
After all changes are made, be sure to click on “Apply” to make sure all
changes are saved into system.
37
WPA-PSK stands for Wi-Fi Protected Access – Pre-Shared Key. WPA-PSK is
design for home users who do not have RADIUS server in their network
environment. WPA can provide better security level than WEP without difficult
setting procedure.
z
z
PassPhrase Key - Enter a WPA Shared Key of 8-63 characters. The
Shared Key should be also applying the Access Point work in the same
wireless network.
Cipher Type - WPA gives you two encryption methods, TKIP and AES,
with dynamic encryption keys. Select the type of algorithm, TKIP or AES.
Remember to click on “Apply” to make sure all changes are made before
leaving this page.
38
Ethernet Client List –
In Ethernet Client List page, you can check all the details here including IP
Address and MAC Address. Press “Refresh” if you add any new Ethernet client
into network. The page will update latest status of current Ethernet network.
39
Wireless Configuration – Wireless Repeater Mode
When set the Access Point to Repeater mode, the AP is able to talk with one
remote access point within its range and retransmit its signal. In order to setup
the AP to work in Ethernet bridge mode, you need to choose “Repeater” mode
and click “Apply” at System Properties page. After need to reboot the AP to
make sure the AP work in repeater mode.
After apply the repeater mode, you can click on “Wireless Network” and
choose “Site Survey” to pick one of the SSIDs you would like to retransmit its
signal. (Please be awarded that while using the repeater mode, the throughput
performance maybe nearly only half compare with access point mode. Because
the repeater needs to communicate with original AP and also the clients
associate to the repeater at the same time.)
40
After click on the “Site Survey” button, you can choose the Access Point you
need to extend its range by clicking on “BSSID” column. Then “Apply” the
change to make sure system working properly with new setting.
After all the changes are made, you can check the “Connection Status” page
to check current SSID and link quality / signal strength. Some more information
is available at this page.
41
42
Appendix A: Glossary
802.11b - An IEEE wireless networking standard that specifies a maximum data transfer rate
of 11Mbps and anoperating frequency of 2.4GHz.
802.11g - An IEEE wireless networking standard that specifies a maximum data transfer rate
of 54Mbps, an operating frequency of 2.4GHz, and backward compatibility with 802.11b
devices.
Adapter - This is a device that adds network functionality to your PC.
Ad-hoc - A group of wireless devices communicating directly with each other (peer-to-peer)
without the use of an access point.
Backbone - The part of a network that connects most of the systems and networks together,
and handles the most data.
Bandwidth - The transmission capacity of a given device or network.
Beacon Interval - Data transmitted on your wireless network that keeps the network
synchronized.
Bit - A binary digit.
Browser - An application program that provides a way to look at and interact with all the
information on the World Wide Web.
CSMA/CA (Carrier Sense Multiple Access/Collision Avoidance) - A method of data transfer
that is used to prevent data collisions.
CTS (Clear To Send) - A signal sent by a wireless device, signifying that it is ready to receive
data.
Database - A collection of data that is organized so that its contents can easily be accessed,
managed, and updated.
DHCP (Dynamic Host Configuration Protocol) - A networking protocol that allows
administrators to assign temporary IP addresses to network computers by "leasing" an IP
address to a user for a limited amount of time, instead of assigning permanent IP addresses.
Download - To receive a file transmitted over a network.
DSSS (Direct-Sequence Spread-Spectrum) - Frequency transmission with a redundant bit
pattern resulting in a lower probability of information being lost in transit.
DTIM (Delivery Traffic Indication Message) - A message included in data packets that can
increase wireless efficiency.
Encryption - Encoding data transmitted in a network.
Ethernet - IEEE standard network protocol that specifies how data is placed on and retrieved
from a common transmission medium.
Firmware - The programming code that runs a networking device.
Fragmentation -Breaking a packet into smaller units when transmitting over a network
medium that cannot support the original size of the packet.
43
Gateway - A device that interconnects networks with different, incompatible communications
protocols.
Hardware - The physical aspect of computers, telecommunications, and other information
technology devices.
IEEE (The Institute of Electrical and Electronics Engineers) - An independent institute that
develops networking standards.
Infrastructure - A wireless network that is bridged to a wired network via an access point.
IP (Internet Protocol) - A protocol used to send data over a network.
IP Address - The address used to identify a computer or device on a network.
ISM band - Radio bandwidth utilized in wireless transmissions.
ISP (Internet Service Provider) - A company that provides access to the Internet.
LAN - The computers and networking products that make up your local network.
MAC (Media Access Control) Address - The unique address that a manufacturer assigns to
each networking device.
Network - A series of computers or devices connected for the purpose of data sharing, storage,
and/or transmission between users.
Node - A network junction or connection point, typically a computer or work station.
Packet - A unit of data sent over a network.
Passphrase - Used much like a password, a passphrase simplifies the WEP encryption process
by automatically generating the WEP encryption keys for Linksys products.
Port - The connection point on a computer or networking device used for plugging in cables or
adapters.
Roaming - The ability to take a wireless device from one access point's range to another
without losing the connection.
Router - A networking device that connects multiple networks together.
RTS (Request To Send) - A networking method of coordinating large packets through the RTS
Threshold setting.
Server - Any computer whose function in a network is to provide user access to files, printing,
communications, and other services.
SNMP (Simple Network Management Protocol) - A widely used network monitoring and
control protocol.
Software - Instructions for the computer. A series of instructions that performs a particular
task is called a "program".
SOHO (Small Office/Home Office) - Market segment of professionals who work at home or in
small offices.
Spread Spectrum - Wideband radio frequency technique used for more reliable and secure
data transmission.
SSID (Service Set IDentifier) - Your wireless network's name.
Static IP Address - A fixed address assigned to a computer or device that is connected to a
44
network.
Subnet Mask - An address code that determines the size of the network.
Switch - 1. A data switch that connects computing devices to host computers, allowing a large
number of devices to share a limited number of ports. 2. A device for making, breaking, or
changing the connections in an electrical circuit.
TCP (Transmission Control Protocol) - A network protocol for transmitting data that requires
acknowledgement from the recipient of data sent.
TCP/IP (Transmission Control Protocol/Internet Protocol) - A set of instructions PCs use to
communicate over a network.
TKIP (Temporal Key Integrity Protocol) - a wireless encryption protocol that provides dynamic
encryption keys for each packet transmitted.
Topology - The physical layout of a network.
Upgrade - To replace existing software or firmware with a newer version.
WEP (Wired Equivalent Privacy) - An optional cryptographic confidentiality algorithm specified
by IEEE 802.11 that may be used to provide data confidentiality that is subjectively equivalent
to the confidentiality of a wired local area network (LAN) medium that does not employ
cryptographic techniques to enhance privacy confidentiality.
WPA (Wi-Fi Protected Access) - a wireless security protocol using TKIP (Temporal Key
Integrity Protocol) encryption, which can be used in conjunction with a RADIUS server.
45
Appendix B: Specification
Standard support
IEEE802.11b
IEEE802.11g
IEEE802.3
IEEE802.3u
Interface
Wireless IEEE802.11b/g
One 10/100 RJ-45 port
SDRAM
8Mbyte
Flash
2Mbyte
Max. Bandwidth
Ethernet Full Duplex: 200Mbps (for 100BASETX), 20Mbps (for 10BaseT)
Half Duplex: 100Mbps (for 100BaseTX), 10Mbps (for 10BaseT)
Wireless 1, 2, 5.5, 6, 9, 11, 12, 24, 36, 48, 54, 108Mbps Auto Fall-Back
Wireless Setting
−
Operation Mode – AP / Wireless Client / Repeater / Wireless
Bridge Point to Point and Point to Multi-Point Mode
−
SSID
−
Channel Selection
−
Transmission Rate (Best, 108, 54, 48, 36, 24, 18, 12, 11, 9, 6, 5.5,
2, 1) in Mbps
Wireless Security
−
Transmit power (Full, Half, Quarter, Eighth, Minimum)
−
Beacon Interval (20-1000): 100
−
Data Beacon Rate (DTIM (1-16384): 1
−
Fragment Length (256-2346): 2346
−
RTS Threshold (256-2346): 2346
−
Short Preamble: Enable
−
Allow 2.4GHz 54Mbps Station Only
−
Protection Mode: Auto / Enable / Disable
−
eXtended Range
−
Distance
WEP setting
−
Authentication type: Open System / Shared Key
−
Shared keys input type: HEX / ASCII
−
Shared keys length: (64-bit, 128-bit, 152-bit)
−
Default WEP Key to use (1-4)
WPA-PSK setting
46
−
PassPhrase
−
WPA Cipher Type (Auto, TKIP, AES)
−
Group Key Update Interval: 300
WPA setting
Software / Firmware
−
Radius Server IP Address
−
Radius Port: 1812
−
WPA Cipher Type (Auto, TKIP, AES)
−
Shared Key
−
Group Key Update Interval: 300
−
Site Survey
−
DHCP Client
−
Wireless access control by MAC address (deny or accept)
−
WPA Support (WPA personal and enterprise)
−
Web-based configuration via popular browser (MS IE,
Netscape…)
Forwarding Mode
−
Windows “Locator” program to help find IP in DHCP client mode
−
Firmware upgrade and configuration backup via Web
−
Reset to default by WebUI
Store and Forward
47
Declaration of Conformity with Regard to the EU Directive 1999/5/EC (R&TTE Directive)
The following standards were applied during the assessment of the product against the
requirements of the Directive 1999/5/EC:
ƒ
Radio: EN 300 328
ƒ
EMC: EN 301 489-1, EN 301 489-17
ƒ
Safety: EN 60950 and either EN 50385 or EN 50371
CE Marking
English
GB
German
DE
Czech
CZ
Denmark
DK
Spanish
ES
Greek
EL
French
FR
Estonian
ET
Italy
IT
Latvian
LV
Maltese
MT
Hungarian
HU
Norwegian
NO
This product may be used in all EU countries without any limitation except in France. The product conforms the
R&TTE Guideline. The EU Declaration of Conformity can be found in the internet at:
http://www.levelone.eu/support.php
Sie können dieses Produkt in ganz Europa verwenden; lediglich in Frankreich bestehen Einschränkungen. Das
Produkt erfüllt die R&TTE-Richtlinie. Die EU-Konformitätserklärung finden Sie im Internet:
http://www.levelone.eu/support.php
Tento výrobek je dovoleno používat v celé Evropě a s omezením ve Francii. Tento výrobek splňuje směrnici
R&TTE. Prohlášení o shodě EU je k dispozici na Internetu na adrese: http://www.levelone.eu/support.php
Det er tilladt at bruge dette produkt i hele europa, undtagen i Frankrig Produktet opfylder R&TTE guidelines. EU
Overensstemmelse deklaration kan findes på internetadressen: http://www.levelone.eu/support.php
Puede utilizar este producto en toda Europa, solamente limitado en Francia. El producto cumple las directivas
R&TTE. Puede encontrar la Declaración de conformidad de la UE en la siguiente dirección de Internet:
http://www.levelone.eu/support.php
Επιτρέπεται να χρησιμοποιείτε αυτό το προϊόν σε ολόκληρη την Ευρώπη, εκτός από τη Γαλλία. Το προϊόν αυτό
συμμορφώνεται με την Οδηγία R&TTE. Η Δήλωση Συμμόρφωσης της ΕΕ μπορεί αν βρεθεί στο ίντερνετ στη
διεύθυνση: http://www.levelone.eu/support.php
Vous êtes autorisé(e) à utiliser ce produit partout en Europe, il y a des restrictions seulement en France. Ce
produit est conforme à la directive R&TTE. La déclaration de conformité européenne peut être consultée sur
Internet à l'adresse http://www.levelone.eu/support.php.
Te võite käesolevat toodet kasutada kogu Euroopas, ainult Prantsusmaal kehtivad selle toote suhtes teatud
siseriiklikud piirangud. Toode vastab raadio- ja telekommunikatsioonivõrgu lõppseadmeid puudutavatele
suunistele. EÜ vastavusavalduse leiate Internetist aadressil: http://www.levelone.eu/support.php
E’ permesso usare questo prodotto in tutta Europa, con solo limitazioni in Francia. Questo prodotto è conforme
alla linea guida R&TTE. La dichiarazione di conformità EU è disponibile in internet
http://www.levelone.eu/support.php
Jūs varat lietot šo produktu visā Eiropā, izņemot Francijā, kur pastāv ierobežojumi. Produkts atbilst R&TTE
vadlīnijām. ES Atbilstības deklarāciju variet atrast internetā pēc sekojošas adreses:
http://www.levelone.eu/support.php
Inti għandek permess biex tuża dan il-prodott fl-Ewropa kollha, b’użu limitat biss fi Franza. Dan il-prodott hu
konformi mal-Linja Gwida R&TTE. Id-Dikjarazzjoni ta’ Konformità ta’ l-UE tinsab fuq l-Internet fuq:
http://www.levelone.eu/support.php
A termék használatát Európa egész területén engedélyezik, Franciaországban azonban korlátozottan
használható. A termék megfelel az R&TTE irányelv feltételeinek. Az EU Megfelelőségi Nyilatkozatot megtalálja
az interneten a http://www.levelone.eu/support.php címen.
Du kan bruke dette produktet i hele Europa, kun begrenset i Frankrike. Produktet samsvarer med R&TTE
retningslinjene. EU-konformitetserklæringen finner du på: http://www.levelone.eu/support.php
48
Netherlands
NL
Polish
PL
Portuguese
PT
Slovak
SK
Slovenian
SLO
Finnish
FN
Swedish
SWE
Lithuanian
LT
Het product kan in alle landen van de Europese Unie, uitgesloten Frankrijk, worden gebruikt zonder enige beperking.
Het product is vervaardigd in overeenstemming met de R&TTE richtlijnen. Een exemplaar van de Verklaring van de
Europese Unie van Overeenstemming kan op de LevelOne Website worden gevonden:
http://www.levelone.eu/support.php
Ten produkt można używać w całej Europie, z ograniczeniem jedynie dla Francji. Produkt ten spełnia wymagania
wynikające z wytycznych R&TTE. Deklaracja zgodności UE jest dostępna w Internecie, pod adresem:
http://www.levelone.eu/support.php
Este produto pode ser utilizado em toda a Europa existindo apenas limitações à sua utilização em França. Este
produto está em conformidade com a Directiva R&TTE. A declaração de conformidade com as normas da UE pode
ser encontrada em: http://www.levelone.eu/support.php
Je dovolené používať tento výrobok v rámci celej Európy, pričom vo Francúzsku je používanie tohto výrobku
obmedzené. Tento výrobok je v súlade so smernicou R&TTE. EÚ prehlásenie o zhode je možné nájsť na internete
na stránke: http://www.levelone.eu/support.php
Ta izdelek lahko uporabljate po vsej Evropi, v Franciji pa ga lahko uporabljate le omejeno. Izdelek je skladen s
smernico R&TTE (Pravilnik o radijski in telekomunikacijski terminalski opremi). EU izjavo o skladnosti lahko poiščete
na internetni strani: http://www.levelone.eu/support.php
Tämän laitteen käyttö on sallittu koko Euroopassa, rajoituksia on vain Ranskassa. Tuote on R&TTE-direktiivin
vaatimusten mukainen. EU:n vaatimustenmukaisuusvakuutus löytyy internet-osoitteessa:
http://www.levelone.eu/support.php
Du får använda den här produkten i hela Europa, endast begränsat i Frankrike. Produkten lever upp till
R&TTE-riktlinjer. EU-deklarationen om konformitet kan hittas på internet: http://www.levelone.eu/support.php
Šį produktą galite naudoti visoje Europoje; ribojimas tik Prancūzijai. Produktas atitinka R&TTE direktyvą. ES
atitikties deklaraciją galite rasti internete adresu: http://www.levelone.eu/support.php
49
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement