gps watch q50 manual

gps watch q50 manual
GPS WATCH Q50 MANUAL
Please read the instruction of the smart watch carefully before using, The
color is subject to the actual product.
I. Quick Start Guide:
1. Remove the battery cover, install a small SIM card, activate the Caller Identification
function and subscribe to a monthly traffic package (the 30M/month package is
recommended, and should be 2G GSM network).
2. Install the battery, put on the cover, and then tighten the screws.
3. Press and hold the ON/OFF key until a ringtone is heard, and a message indicating that
the watch is being started up is displayed on the screen. The watch can not be powered off
locally after the major guardian's number is set. To power it off, should use the mobile
APP.
4. Download the app to your mobile phone (scan the two-dimensional code on the last page
of this guide), and then register it.
5. Charging: Use the USB charging cable to insert the USB interface on the left side of GPS
watch, and connect the other end of the charging cable to a computer or the charger.
6. Emergency Call: Press the side KEY 1, side KEY 2 or side KEY SOS to dial the
familiarity number that is preset through the APP.
7. Smart calling: all devices can call the watch phone directly when they are sent out from
the factory, after setting the main monitor number, white list phone numbers can call the
device only after setting the main monitor numbers, SOS numbers. (To prevent harassing
phone calls)
II. Descriptions of Smartwatch
III. Screen output
IV. Packing list
Item NO.
Accessories
Quantity
1
device
1
2
user manual
1
3
charging cable
1
4
lanyard
1
V. Product Features:
1) GPS +LBS (Base station positioning) dual mode positioning
2) SOS function, two way communication
3) GEO fence
4) Anti-drop alarm
5) Low-battery alarm
6) Real time tracking
7) Tamper alarm
8)Calling and Intercom
If the watchband is unbuckled after the watch has been on wrist for more than three minutes,
the APP client will receive a warning message showing that the watch is taken off. You can
disable this function when the product is put aside.
8) Monitoring call
Enter your phone number in the dialog box, click OK, and the watch will dial your phone
number immediately after a command returns. When in conversation, the speaker of the
watch is disabled and does not make any sound.
VI. Simple use instruction
VII. Operations on the Client
1. Downloading and Logging In to the App
● Use the smartwatch to scan the two-dimensional code as below to obtain a download
address.
● Start the APP client, please register the tracker. You are advised to change the
password upon the first use.
2. Real-time Tracking
● Enter the Real-time Tracking menu, and you can see the location of the watch. Click the
Refresh button, the location of the watch can be updated. The map can be resized as you like.
2. Intercom
● Long press the start button on the watch to record the voice, release the power button to
send the record to APP.
● When watch received a record, the screen will have a voice sign, short press SOS key to
play the record, all voice broadcast, sign will disappear.
3. Settings
● Interval of sending GPS data: There are three modes available.
i. Quick positioning: position information is reported every 10 seconds. This mode allows
you to receive position information frequently, but is power-consuming. Please do not set
your watch to run in this mode for a long time.
ii. Default setting: position information is reported every 10 minutes. This mode is
recommended.
iii. Power-down Mode: position information is reported every 1 hour.
●Major Guardian's Number: It refers to a phone number to receive power shortage
warning message. After setting the major guardian's number, it is impossible to turn off the
watch directly. Instead, pressing and holding the ON/OFF key will originate a call to the
guardian's number.
● Monitoring Call: Enter your phone number in the dialog box, click OK, and the watch
will dial your phone number immediately after a command returns. When in conversation,
the speaker of the watch is disabled and does not make any sound.
●Emergency Number: Besides Dad's and Mom's numbers, the number of another guardian
can also be set. Enter a guardian's number, and confirm. The setting is successful if the watch
shows that the command has been returned. Press the Dad key for 3 seconds, the watch will
dial the first emergency number (to send out a distress signal).
Set a white list: add phone numbers to the white list. Then the device can receive calls only f
rom users on the white list, in addition to the main number and emergency numbers, to avoid
unwanted calls.
● Tamper Alarm: If the watchband is unbuckled after the watch has been worn for more
than three minutes, the APP client will receive a warning message showing that the watch is
taken off. You can disable this function when the product is put aside.
● Setting low battery alarm: The watch battery capacity display percentage. If less than
15%, it will alarm after 5 minutes, the watch will send alarm message to the App.
● Setting pedometer: The watch have vibration sensor, User can turn on the pedometer
function during exercise, it will begin to counter steps, the watch will indicate the users’ steps
number real time so that the users can know the exercise station through the APP, the watch
pedometer state will change to week after turn off the pedometer function.
4. Other Features:
● History: Records generated in the last 90 days are accessible. You can select whether to
display the positions with the LBS.
● Electric Fence: After adding an electric fence name, you can set a fence with the watch as
the centre and with a radius of 100 to 5000. The APP Client will receive an alarm when the
watch enters or exits the fence.
● Watch Message: All alarm messages the watch has received will be displayed.
VIII. FAQs:
● It prompts that the number you dialed is busy now when dialing the watch with your
mobile phone. (The SIM card has not activated the caller identification function yet, so that
the watch is unable to identify any number. Please activate this function first.)
● If Sending or Sending Failed is always displayed after commands are set on the APP
client, the reason may be one of the following:
a There is no signal or weak signal of a GPRS network at the place of the watch, so that
GPRS data cannot be transmitted;
b The GPRS access function has not activated for the SIM card in the watch. It is
recommended that you subscribe to a 30M monthly GPRS traffic package.
c The line is engaged. GPRS data transmission will be automatically stopped during a
GSM-enabled call.
● The APP client showed that the watch is off-line all the time:
a The balance of the SIM card is insufficient, so that data transmission and call services are
prohibited;
b The watch is powered off or suffering a power outage;
c There is no signal or weak signal at the place of the watch (In such case, the watch data
rarely can be uploaded to the server).
● The distance between the watch and a base station is as long as several hundreds
meters: The watch is in base station positioning state. The positioning precision depends
on the density of base stations around the watch. The actual precision of base station
positioning is 50 to 1000 meters.
Tips:
The product is specifically designed for children, elders and other groups needing custody.
Do not use the product for illegal purposes, such as tracking and tapping other persons'
privacy. All consequences arising from such illegal actions should be borne by the user! We
will not be responsible for any loss incurred there from.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising