P1 Agile Inst
Steeicraft Agile—
Twin Stroller
BRITAX CHILDCARE PTY. LTD A Britax International company.
(Incorporated in Victoria) A.B.N. 55 006 773 600
99 Derby Road, Sunshine, Victoria 3020, Australia
Phone: (03) 9288 7288 Fax: (03) 9311 5798
CUSTOMER SERVICE
1300 303 330 - Australia 0508 688 822 - New Zealand
Due to our continuing program of development, Britax reserves the right to alter
the specifications, color or design without any further notice.
The Steelcraft trademark is the property of Britax Childcare Pty.Ltd - Australia.
The Britax trademark is the property of Britax Excelsior Limited - UK.
Visit the Britax website at: www.britax.com.au or email us at au-custserv@britax.com
Due to the variations in the style and design of our products the illustrations used
in this instruction booklet are generic.
This product is designed to comply with Australian and New Zealand standard
AS/NZS2088 “Prams and Strollers - Safety Requirements.”
©2010 Copyright Britax Childcare Pty. Ltd. Australia
SUITABLE FOR USE WITH THE STEELCRAFT INFANT CARRIER (SOLD SEPARATELY)
IMPORTANT: KEEP THIS BOOKLET IN A SAFE PLACE FOR FUTURE REFERENCE.
Series No. SH819
Art No.4001435_C
RETAIN FOR FUTURE REFERENCE.
READ ALL INSTRUCTIONS CAREFULLY BEFORE ASSEMBLY AND USE
OF THIS STROLLER. ALWAYS FOLLOW THE INSTRUCTIONS.
THE CORRECT USE AND MAINTENANCE OF THIS PRODUCT IS
ESSENTIAL.
AWARNINGS: ro AVOID INJURY OR DEATH:
ALWAYS APPLY THE BRAKES WHENEVER THE STROLLER IS
STATIONARY.
FOLLOW THE MANUFACTURERS INSTRUCTIONS.
* DO NOT LEAVE CHILDREN UNATTENDED.
« SECURE THE CHILD IN THE HARNESS AT ALL TIMES.
- DO NOT CARRY EXTRA CHILDREN OR BAGS ON THIS STROLLER.
* MAKE SURE CHILDREN ARE CLEAR OF ANY MOVING PARTS IF YOU
ADJUST THE STROLLER.
* USE THE HARNESS AT ALL TIMES.
« WHEN NOT IN USE DISCONNECT SHOULDER STRAPS FROM THE
WAIST STRAPS AND BUCKLE TO PREVENT STRANGULATION.
+ Check that all safety locks are engaged before placing a child in
the stroller.
Ensure your child is secured with a correctly adjusted safety
harness.
* Use the tether strap to prevent the stroller from rolling away.
* Never let go of the stroller when parked on an incline because it
may slide or tip over. Always park on a flat surface.
- Remove the child from the stroller before going up or down stairs
or escalators.
« To prolong the life of your stroller and accessories keep it clean
and do not leave it in the direct sunlight or in the car boot for
extended periods of time.
* Removable fabric covers and trims may be cleaned using warm
water with a household soap or mild detergent. Allow it to dry fully,
preferably away from the direct sunlight.
Non removable fabric covers and trims may be spot cleaned using
a damp sponge with soap or a mild detergent. Allow it to dry
completely before folding or storing it away.
In some climates the covers and trims may be affected by mould
and mildew. To help prevent this occurring, do not fold or store the
product if it is damp or wet. Always store the product in a well
ventilated area.
When using your stroller at the beach - completely clean your
stroller afterwards to remove the sand and salt from the
mechanisms and wheel assembly. Sand and salt will cause
premature wear and corrosion.
If there are compression marks on the tyres - Use a domestic
hair dryer to gently warm (DO NOT OVERHEAT) the tyre and the
compression marks should slowly disappear.
Always check parts regularly for tightness of screws, nuts, and other
fasteners - tighten if required. To maintain the safety of your nursery
product, seek prompt repairs for bent, torn, worn or broken parts.
THIS PRODUCT IS NOT INTENDED FOR COMMERCIAL USE.
16. TO RELEASE THE INFANT CARRIER (Cont)
C Lift and remove the Infant Carrier away from the stroller.
D To remove the adaptors, press the red button in on the inside of
the adaptor and pull the adaptor up.
Adaptors
Red button
A WARNINGS
Do not allow children to stand on the seat.
Do not hang bags or goods from the handle as this could cause
the stroller to tip over.
To prevent the risk of the stroller catching fire, do not park it near an
exposed heat source such as a radiator, an open fire or a barbecue,
etc.
Do not run while using this product.
Always lock swivel wheels when on rough surfaces as this will help
eliminate wheel wobble.
Always raise the leg support (where fitted) to its highest position
when transporting a baby. This will reduce the risk of the baby
falling out through the front of the stroller.
It is unsafe to use accessories other than those tested and approved
by Britax. For maximum safety only use accessories designed for this
stroller,
Do not place more than 2kg in each basket or 1kg in each Canopy
pocket (if supplied)
The maximum weight of the child in each seat using this product is
not to exceed 20kg for the Stroller or 9kg for the Infant Carrier.
FOR WARNINGS ON ACCESSORIES - REFER TO THEIR INDIVIDUAL
SECTIONS IN THIS BOOK. THE MAXIMUM WEIGHT VARIES FOR EACH
ACCESSORY.
EEE ——
www.britax.com.au
www.britax.com.au
WARNINGS CONTINUED
A IMPORTANT
The upright positions are not suitable for use with children less
than six months old. The lowest recline position should be used
to transport babies, and the backrest can be adjusted to a more
upright position as the child grows older and is able to support
its head without assistance.
A SAFETY WARNING
The sun is very strong. DO NOT LEAVE YOUR CHILD EXPOSED TO THE
SUN. The canopy or hood on this product will not give your child
total protection from the harmful rays of the sun.
16. TO RELEASE THE INFANT CARRIER
A To remove the Infant Carrier, squeeze both handle latches in to
release the locks. The indicator will now be RED.
Handle latch
5 Continue to rotate the handle forward until it returns to the
upright position. Release the latches, the indicator should now
be GREEN.
Handle latch
Indicator
15. TO INSTALL THE INFANT CARRIER (Cont) PARTS LIST
E Release the handle latches. Then with one hand holding the front
of the Infant Carrier, push the Infant Carrier handle all the way
down until you hear it lock into the adaptors. The handle indicator
should now be GREEN and the Infant Carrier should be locked
into the adaptors. If the indicator is RED the Infant Carrier handle
is not in the locked position, repeat step D.
@ В
Nu
3 2xCanopies
a
C 2x Rear Wheels D 2xFrontWheel sets
IMPORTANT: Ensure that the Infant Carrier is locked into place by
pulling up on both sides. Do not use the Infant Carrier if it is not
correctly installed.
Please Note: The Infant carrier has been fitted with a hood when
using the stroller. The hood can also be used in the car. Refer to
the Infant Carrier instructions regarding placing and securing
N И
your baby in the Infant Carrier.
Е 2x Infant Carrier Adaptors
www.britax.com.au www.britax.com.au
ASSEMBLED STROLLER - PARTS LIST
2“
Canopy
Adjustable Front canopy
handle button tube
Upper seat
Tether Strap Inner seat
— Folding straps
Shoulder pads Lower seat
Harness Footrest
Sure Lock release button be Zipper
o PS
Frame lock a e Leg rest
/
Front leg tube К (7 Foot
Ni A ©
Ud
uy
Front wheel
swivel lock
Basket
Canopy window cover
Canopy window
Canopy back flap zipper
www.britax.com.au
15. TO INSTALL THE INFANT CARRIER (Cont)
C Lower the Infant Carrier into the adaptors. Press down firmly on
both sides.
The Infant Carrier now needs to be locked securely into the
adaptors. Squeeze in and hold the latches on either side of the
handle, rotate the handle backwards. The GREEN indicator will
now turn to RED.
www.britax.com.au
15. TO INSTALL THE INFANT CARRIER (Sold Separately) 01. TO OPEN THE STROLLER
A Release the storage latch (1) located on the rear leg.
Open the frame as shown by the arrows (2) until you hear a‘click’
which indicates the frame is fully opened and locked.
A Stand in front of the stroller and pull the fabric back from the sides
of the stroller to expose the stroller hinge.Take one Infant Carrier
adaptor at a time and insert the adaptor into the stroller hinge.
Push on the adaptor until you hear a ‘click’ which indicates the
adaptor has locked in. Pull up on each adaptor to check they have
have fully locked in.
02. TO ASSEMBLE AND REMOVE THE FRONT SWIVEL WHEELS
i "
1
| É
} I Al
О
NT
an EL
A
e = p=
pt
Lo
A To assemble the front swivel wheel assemblies, insert the swivel
Please Note: Fit adaptors standing in front of the stroller. wheel assembly and push it into the wheel mouldings until you
В Face the feet end of the Infant Carrier towards the stroller hear aclick' which indicates the wheel is locked in.
backrest. With the Infant Carrier handle in the upright position Check the wheel assembly is fully locked by pulling against it.
locate the Infant Carrier handle mouldings over the adaptors on
on. B To remove the front swivel wheel assembly, locate and press in
either side. Notice the indicator is GREEN y Р
the Black button behind the wheel moulding.
www.britax.com.au www.britax.com.au
03. TO FIT AND REMOVE THE REAR WHEELS
15. TO INSTALL THE INFANT CARRIER (Sold Separately)
A To fit the rear wheels, insert each wheel axle into the moulding
and push in until locked. You should hear a ‘click’ which indicates /AWARN | NGS
the wheel has locked in. Pull on the wheel to make sure it is
engaged. Repeat the process if not locked in.
THE STEELCRAFT INFANT CARRIER IS THE ONLY INFANT CARRIER
DESIGNED TO FIT THIS STROLLER.
«THE INFANT CARRIER MUST BE CORRECTLY FITTED AND
LOCKED ONTO THE STROLLER USING THE SUPPLIED ADAPTORS.
«THE INFANT CARRIER MUST ONLY BE USED IN THE REARWARD
В To remove the wheels, pull the metal latch downwards on the
underneath of the brake moulding to release the wheel, and then
pull the wheel off.
A N A ÓN FACING POSITION, FITTED TO THE STROLLER FACING TOWARD
€
THE STROLLER HANDLE.
«SECURE THE CHILD IN THE HARNESS AT ALL TIMES.
«DO NOT LEAVE THE CHILD IN THE INFANT CARRIER FOR
»
EXTENDED PERIODS.
LU Metal Latch + THE INFANT CARRIER IS DESIGNED TO PROVIDE MOBILITY
a J Ne OUTSIDE OF THE CAR BUT IT SHOULD NOT BE USED INSTEAD OF
AN APPROPRIATE COT.
04. TO USE THE SWIVEL WHEELS ° THE INFANT CARRIER MUST BE REMOVED FROM THE FRAME
A Press the swivel lock down to lock the swivel wheels. BEFORE FOLDING.
Push the swivel wheel lock up to allow the wheels to swivel. * THE MAXIMUM WEIGHT OF THE CHILD USING THIS PRODUCT
IS NOT TO EXCEED 9kg.
Note: Always lock the swivel wheels when using the stroller on
rough surfaces as it will minimise wheel wobble. , , , ,
Please Note: These Instructions are for installing and removing
the Infant Carrier on the stroller only.
For installing and and proper care of the Infant Carrier in the
car please follow the Instruction book that is included with the
Infant Carrier.
www.britax.com.au www.britax.com.au
14. TO FOLD THE STROLLER (Cont)
B2 Move to the front of the stroller and with both hands pull up on
both folding straps (2) as shown by the arrow. The stroller will
now fold.
C Ensure the frame is secured with the storage latch. Carry the
stroller by the folding strap or by the frame.
www.britax.com.au
~
05. TO ATTACH AND USE THE CANOPIES
Al
A2
To attach the canopies, insert the canopy mouldings into the
frame mouldings until they connect together. The back flap of
the canopy can be attached or removed from the main canopy
with the zipper attachment.
Attach the snaps located on the straps on the sides of each
canopy to the top of the outer handle tubes, then fold the strap
up under the canopy back flap and secure strap with hook and
loop to the underneath of the canopy.
www.britax.com.au
05. TO ATTACH AND USE THE CANOPIES (Cont)
A3 Thread each loop strip through the guide moulding located on
the middle handle tube.Then attach the loop strip to the hook
strip underneath the canopy.
A4 Attach the hook square on the inside of the canopy backflap to
the loop strip on the side of the stroller.
www.britax.com.au
14. TO FOLD THE STROLLER
A To prevent the canopy back flaps from dragging on the ground
when the stroller is folded, either remove the back flaps by
opening the zippers at the top of the back flaps, then close the
canopies, or push each canopy back flap into small mesh pocket
on each backrest.
51 Rotate the handle in towards the canopy before you fold the
stroller (See page 19) as this will assist in preventing damage to
the stroller handle when folding. Press in the RED Sure Lock
release button (1) located on the right hand side of the stroller.
7
www.britax.com.au
13. TO USE THE STROLLER 05. TO ATTACH AND USE THE CANOPIES (Cont)
* With your hand through the wrist tether strap loop, push the A5 Attach the hook strip on the inside edge of the canopy to the
stroller holding the handle. loop strip on the side of the stroller.
The stroller can be steered in the desired direction - allowing the
front wheels to swivel will make this easier.
The front wheels may wobble or oscillate when walking fast.
* Locking the front swivel wheels will stop this.
» The stroller can be taken up kerbs by either pressing down on the
handles and raising the front wheels or turning the stroller around
and pulling the stroller up the kerb.
« Caution is required when pushing the stroller on a steep slope as
the stroller may become unstable. Always hold the handles firmly.
* Whenever you stop, always apply the brakes before you leave the
stroller.
{JA Chef
i
al
is
8
ОВ
В:
It
B To remove the canopy, press in the buttons on the canopy
mouldings and pull out of the frame mouldings.
The button on the
canopy moulding
www.britax.com.au www.britax.com.au
05. TO ATTACH AND USE THE CANOPIES (Cont) 12. TO USE THE STORAGE BASKET
C To adjust the canopy, open by pulling canopy forward, or close A When the stroller seats are in the full recline position it may be
by pushing canopy backward. a = N difficult for you to access the storage basket from the rear of the
stroller. For easier access undo the zippers on the leg rest to
access the storage baskets from the front of the stroller.
\_
D To open the canopy window lift the canopy window flap away
from the canopy.
Canopy window flap
Canopy window
Canopy back flap
Zipper
E For additional air circulation the back flap of each canopy can be
removed by opening the zipper. To reattach the back flap to the
main canopy secure with the zipper.
www.britax.com.au www.britax.com.au
11. TO FIT THE RAIN COVER 06. TO ADJUST THE BACKREST
A Place the rain cover over extended canopy as shown. To secure /N o ,
the rain cover, attach the hook and loop straps on the front of WARN NG o ENSURE THAT YOUR CHILD'S LIMBS
the rain cover around the wheel mouldings above the swivel ARE INTHE CENTRE OF THE SEAT AND SUPPORT YOUR
wheel lock then attach the hook and loop strips on the sides of CHILD'S WEIGHT WHEN USING THE BACKREST.
the rain cover.
A To raise each backrest, hold the main adjuster moulding in one
de > hand, then grasp the plastic rings fixed to the adjuster straps
> with the other hand. Push up on the main adjuster moulding
at the same time pull the adjuster strap to the desired position.
B To lower each backrest, support the backrest with one hand and
with the other hand pull down the on the backrest adjuster
button and lower the backrest to the desired position.
Main adjuster —
moulding —— Backrest adjuster button
Plastic rings
www.britax.com.au
www.britax.com.au
07. TO USE THE BRAKES 09. TO ADJUST THE PIVOTAL HANDLE
A . A There is an handle adjusting button on the inside of each handle
WARN | NG: ALWAYS APPLY THE BRAKES WHEN moulding. Press both adjusting buttons in together and rotate
THE STROLLER IS NOT MOVING. THE STROLLER MAY ROLL the handle up or down to the desired position, then release both
AWAY EVEN IF LEFT UNATTENDED FOR A FEW MOMENTS. buttons.
A To lock the rear wheels, press down on the brake pedal. Check и Sl
that the brakes have locked by trying to push the stroller
forward. If not locked, repeat this step.
B Torelease the brakes, push up on the brake pedal.
N—
(
a A A WARNING: use THE TETHER STRAP TO PREVENT
THE STROLLER ROLLING AWAY.
A A wrist tether strap is provided on the handle grip. Slide your
hand through the tether strap loop whenever you use the
stroller. Only remove your hand from the tether strap loop when
when the brakes have been applied to the stroller wheels.
www.britax.com.au www.britax.com.au
08. TO SECURE YOUR CHILD IN THE HARNESS(Cont)
08. TO SECURE YOUR CHILD IN THE HARNESS
A WARN | N G: USE THE HARNESS AT ALL TIMES.
When not in use disconnect shoulder straps from the waist
strap and buckle to prevent strangulation.
A five point harness is provided to restrain your child.
Buckle tongues separate for added safety.
To reconnect buckle tongues and to secure the child in the harness
please follow the steps below carefully.
F Torelease the buckle. Squeeze the top and buckle tongues Shoulder strap
together with enough pressure so the buckle tongues can
release from the buckle housing.
G The stroller seat has *2 or 3 sets of Buckle
harness slots at different heights to housing
accommodate the child.
To change the shoulder harness height,
push the shoulder harness tongue out of
the current harness slot and through the
back of the seat.
* Depending on the model
A Position the shoulder strap tongue (A) on the top of the waist
buckle tongue (B) on both sides.
www.britax.com.au www.britax.com.au
08. TO SECURE YOUR CHILD IN THE HARNESS (Cont) 08. TO SECURE YOUR CHILD IN THE HARNESS (Cont)
ÓN
Shoulder)
4 bar
slider
Buckle
housing
«= | )
[A]+[B]
D Tighten or loosen the waist straps, hold and lift the 4 bar slider
N Crotch strap D and then pull the harness strap, to adjust to the desired fit. The
waist strap needs to fit firmly around the child.
B Push both buckle tongues (A+B) into the buckle housing
(C) until the buckle tongues lock into position.
= Tighten or loosen the shoulder straps, slide the 3 bar slider up or
down to adjust to the desired fit. Always adjust the harness strap
when changing the seating position of the child.
O slider Crotch strap J
C Tighten or loosen shoulder and crotch straps by sliding up and
down the 3 bar sliders. A CAUTION: bo NOT SLIDE 3 BAR SLIDER OVER THE
SEWN TAB ON SHOULDER HARNESS.
www.britax.com.au www.britax.com.au
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising