ProSharp SkatePal-Pro² - ORIGINAL INSTRUCTIONS

ProSharp SkatePal-Pro² - ORIGINAL INSTRUCTIONS
ProSharp SkatePal-Pro² - ORIGINAL INSTRUCTIONS
1.
2.
Read the Instructions Manual featured on the next page carefully! Continue from here
after that.
Setup and sharpening:
QUICK-REALEASE
HANDLE/CLAMP
GRINDING
WHEEL DOOR
A. Place the machine on a flat and steady workbench with a height between 80 and 100 cm.
KEY LOCK
B. Make sure that your ear, eye and breathing protection gear is being worn correctly!
C. Make sure that the installed grinding wheel has the hollow radius you wish to receive by
opening the grinding wheel door and look on the text on it .(if it has not, change it
according to the instructions manual on the next page).
D. Plug in the power cord.
E. Clamp the skate in the slot on the top of the machine using the quick-release handle, and
make sure that the blade reaches below the clamp-steels .You can to this by looking inside
the grinding wheel door.
F. If you are about to sharpen figure skates or long-distance skates also make sure that the
wheel is made for this type of sharpening. The wheel should be 60 mm in cross section, and
the text on it should say either “FIG” or “BANDY”. To sharpen figure skates you must also
have a type of device to measure in the height of the skate for the grinding wheel will miss
the toe picks. How to do this is featured on the last page.
G. Now put the grinding wheel door back on. Attach the vacuum cleaner, turn it on, Turn
the machines power switch on and press the start button the amount of cycles you wish the
machine to run.
H. When the machine has stopped grinding, turn it OFF, release the quick-release handle
and take the skate out, look on the result, and if it is satisfying, repeat the same procedure
with your next skate, if it is not, sharpen it again until you have achieved a satisfying result.
3.Maintenance:
After sharpening unplug the power cord. Open the grinding wheel door and clean the
machine inside with a vacuum cleaner or with a magnetic stick. Clean the machine after
use, and always before transport.

IMPORTANT! Machine’s life time is directly reflected to the maintenance of the
machine. Always lock the machines locks on both ends when transporting. Disconnect
the power cord before changing the grinding wheel.
Never start the machine without a skate.
ON/OFF
VACUUM
CLEANER INPUT
START/STOP
CYCLE
POWER
CORD INPUT
ProSharp
Original Instruction Manual
Read the operating instructions carefully before use. Operations that are not in accordance with the
manual and/or disregard safety instructions may damage the machine and/or result in serious personal
injury.
Description of the machine: ice skate sharpener
Safety Information
• ProSharp SkatePal-Pro² may only be used for sharpening skates.
• Only the original ProSharp EP- grinding wheels are to be used in the machine.
• No modifications or design changes are allowed.
• All operators must read and understand instructions regarding operation and maintenance contained
in this manual, before using the machine.
• Operators under 18 years of age are NOT allowed to use the machine.
Hazards
• Before using the machine, ensure there are no damages caused, for example, during transport.
• The SkatePal is equipped with grinding tools which may cause injury.
• The operator must stand in front of the machine.
• Children and others than the machine operator must be kept away from the machine at a safe
distance of 2 meters.
• The operator may never bend over or place hands on the machine during skate sharpening.
• Grinding dust can escape from the machine; therefore the operator must wear protective eyewear and
breathing protection when machine is in use. It is also highly recommended to use ear protection, when
the machines sound-level during sharpening due to differences in the skate-steels, can exceed beyond
pleasant level, or in worst case harm your hearing.
Connection
• Connect the power cord, 1-phase, 100-240 volt, 50 — 60 Hz.
Placement
• The machine must be placed on a flat, steady work bench with a height between 80 to 100 cm.
Maintenance
• Control and clean the machine daily after the usage and always after every 30 pairs of skates
• Remove the plug before carrying out any adjustment, servicing or maintenance.
2. Choose the sharpening cycles from 1 to 5 by quickly pushing the start button. 1 push is worth of 1
cycle and 5 pushes are worth of 5 cycles. Grinding is finished when the wheel is back in the start
position and the motor has stopped. Push the start button once during sharpening = reset/stop.
3. Check the sharpening result on the skate blade. (if not perfect, repeat the sharpening)
Emergency stop
Push once the start button when the motor is doing the first half-cycle (going to left). Grinding will stop
and the wheel comes back to the home position. One push after the first half-cycle (going to right)
resets counter and takes the wheel back to start position after the cycle is finished. Two pushes after
the first half-cycle will stop the grinding and takes the wheel back to home position.
Hollow settings and changing of the grinding wheel
Changing of the SkatePal EP- grinding wheel should be done only when the power cord is
disconnected.
1. Choose a grinding wheel with a hollow from 3XS to 2XL. It correlates to a hollow radius from 7mm
hollow = XXS (7mm) to 28mm =2XL (28mm) to entirely flat = XX. Other radius of hollows can be
ordered from ProSharp with an 8 weeks delivery time.
2. Open the grinding wheel door; release the grinding wheel thumbscrew by turning to the left. Remove
the wheel and replace it with another wheel. Return the thumbscrew and tighten it gently by turning to
the right.
Adjusting the grinding wheel sideways
Adjust the grinding wheel in small steps, 1/8 round at the time. An easy way of changing position of the
grinding wheel is to first drive the wheel to the left, so you get more room to adjust the screw. To do
this, push start button for five seconds and keep the button down. Wheel will start go to the left without
grinding. Once you let go off of the start button, the wheel will stop. (If you want the wheel even further
left, push the button again for five seconds and repeat previous steps). Push once more and the wheel
will come back to the home position
Adjusting of the centering of the grinding wheel can be done by screwing the thumb screw.
Clockwise moves the wheel towards you and anti-clockwise moves the wheel from you. The
thumb-screw can be found beside the grinding wheel, see picture below.
After grinding:
Unplug the power cord. Clean the machine from dust with a dust cleaner or you can also use a magnetic stick.
Every B64 wheel lasts around 1000~ cycles
Change the grinding wheel according to the instructions. It is worn out when it is no longer taking
away material from the steel and/or gives an unsatisfying result.
After 1-3 years or around 10,000~ cycles
Service should be made by an authorized service technician.
Sharpening of skates
1. Clamp the skate into the middle, sideways, of the skate holder, always with the heel of the skate
placed towards the grinding wheel.
Technical Data
• Power
• Weight
• Length
• Noise level
Pmotors total 150W,
32,6 lbs (14.8 kg)
27.5 " (700 mm)
X dB
AC INPUT 100-240vac 50/60hZ 3.6A
Width 8.6”
(220 mm)
Height 12.6” (320 mm)
Read the installation and operating instructions carefully before using the
machine. Usage that is not in accordance with the instruction manual and/or
disregard safety instruction, may cause injury or death, and damage the
machine.
5.
Installation instructions
6.
1.
7.
2.
Unpacking and installation:
Open the SkatePal by unlocking the locks on both sides of the machine with one of the
two(identical) included keys.
Plug the power cord of the machine on the right side of the machine. Connect a hose of
a vacuum cleaner to the right side of the machine. Use the machine in a warm, dry and
well lit room.
3.
The SkatePal-Pro includes: SkatePal-Pro skate sharpener, 1 x EP-grinding wheel
(mounted), 2 x key and an instruction manual.
4.
After usage of the machine clean the machine and the working space properly. Unplug
the power cord and vacuum cleaner hose. Before transportation ensure that the
grinding wheel is steadily locked so it can’t move during transportation. Lock the locks
on both sides of the machine.
Operation instructions and Safety precautions:
WARNING! When using electric tools basic safety precautions should always be followed to
reduce the risk of fire, electric shock and personal injury. Read all these instructions before
attempting to operate this product and save these instructions. The use of any accessory or
attachment other than one recommended in this instruction manual may present a risk of
personal injury.
1.
Always use eye, ear and breathing protection. Always connect a vacuum cleaner to the
machine to minimize dust occurring outside the machine.
2.
Wear proper apparel. Do not wear loose clothing, gloves, neckties, rings, bracelets, or
other jewelry which may get caught in moving parts. Non slip footwear is
recommended. Wear protective hair covering to contain long hair.
3.
Do not expose the machine to rain. Do not use the machine in damp or wet
environment. Keep work area well lit. Do not use the machine in the presence of
flammable liquids or gases.
4.
Guard against electric shock. Avoid body contact with earthed or grounded surfaces
(e.g. pipes, radiators, ranges, refrigerators)
8.
9.
10.
11.
12.
13.
14.
15.
16.
Keep other persons away. Do not let persons (especially children) not involved in
the work touch the machine or the extension cord, and keep them away from the
work area. Make workshop child proof with padlocks, master switches, or by
removing starter keys. Do not overreach. Keep proper footing and balance at all
times. Do not stand on the machine.
Never leave machine running unattended. Turn power off. Don’t leave the machine
until it comes to a complete stop.
Don’t force the machine. It will do the job better and safer at the rate for which it
was designed.
When not in use always disconnect the power cords.
Stay alert. Watch what you are doing, use common sense and do not operate the
machine when you are tired.
Check damaged parts. Before further use of the machine, it should be carefully
checked to determine that it will operate properly and perform its intended function.
Check for alignment of moving parts, binding of moving parts, breakage of parts,
mounting and any other conditions that may affect its operation. A guard or other
part that is damaged should be properly repaired or replaced by an authorized
service centre (contact us for the location of your nearest service centre) otherwise
indicated in this instruction manual. Have defective switches replaced by an
authorized service centre. Do not use the machine if the switch does not turn it on
and off.
Store the machine properly in a dry locked-up place, out of reach of children.
Never yank the cord to disconnect it from the socket. Keep the cord away from
heat, oil and sharp edges.
Avoid unintentional starting. Ensure the switch is in “off” position when plugging in
the cord.
This electric machine should be repaired by qualified persons using original spare
parts, otherwise this may result in considerable danger to the user.
Maintain the machine with care. Follow instruction for lubricating and changing
accessories. Inspect machine cords periodically and if damaged have them
repaired by an authorized service facility. Inspect extension cords periodically and
replace if damaged.
Disconnect the machine before servicing and when changing accessories, such as
grinding wheels. Do not touch the motor of the grinding wheel directly after
sharpening because it can be hot. Detailed instructions how to change the
grinding wheel are on page 2. When servicing use only identical replacement
parts. Other parts than those recommended by the manufacturer may
present a risk of personal injury.
17. Keep work area clear- Cluttered areas and benches invite injuries.
18. Use right tool- Do not use the tool for purpose not intended.
PUT ON YOUR EAR EYE AND BREATHING PROTECTION BEFORE PERFORMING FOLLOWING STEPS!
Take the grinding wheel door off and make sure that the smaller 60 mm wheel is installed, it
FIG
ut the lowest spike in
the bridge, then clamp the skate firmly, make sure it is not easily moved, look inside the machine
to make sure that the heel sits around 2-3 mm below the clamping steel, that way it will not
damage the clamping steels, and not round the heel of the skate. Then carefully take away the
toe protector device, press and hold the start/stop button, and it will drive the grinding wheel
towards the toe picks without the grinding wheel spinning. This will allow you to make sure that
the grinding wheel will miss the toe picks, and also at what point it will hit the heel of the skate,
when you release the button it will stop, and when you push again, it will return to start position,
it will take some adjustment before you can obtain a satisfying result so please be patient, after
you have found the correct setting it will not be necessary to adjust it anymore for your SkatePal ,
so make sure you have tightened the nuts firmly. When you are ready to start sharpening
continue to the first page. A tip is to start by using an old skate, that way you will not take the risk
of damaging more expensive skates.
To make the wheel
come further away
from the toe picks,
adjust the screws
down.
ProSharp Toe Pick protector is
not included with the machine,
call us, or visit our website for
details.
Adjust the height in
small steps by using a
7mm spanner.
To make the grinding
wheel come closer to
the toe picks, adjust
the screws up.
START STOP
CYCLE.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising