Setup Turnigy 9X

Setup Turnigy 9X
Setting up your Turnigy 9X transmitter
Unfortunately, there is a woeful lack of information in the Turnigy 9X manual (available at
HobbyKing from the Turnigy 9X page) so I have jotted down a few possible simple settings here to
get you started, if you are using the standard V2 software. These are for powered gliders, but are
set as ACRO in order to have correct THR (Throttle) settings and Throttle Cut capability. (Glider
setting has ARB, or Airbrake, which requires reverse setting if using powered glider; also Butterfly
uses ThrCut switch.) I haven’t got powered landing gear so have not figured out how to do this
without using the Gear (GYR) channel.
Ailerons – If using Y-connector, use AilDiff, set all at 100% (unless requiring other functions as
below, with dual ailerons, using Ail and Aux1).
Two flap settings with 3-way flap switch:
(note Uprate and Dnrate correspond to Gear switch positions Up and Down, thus
cancelling its position)
Ch5 set to Gear.
Mix 1 - Save this one in case you need it for dual ailerons (see below).
Mix 2 - Master GYR, Slave FLP, Offset 0, Uprate 100, Dnrate -100, SW NOR
Mix 3 - Master GYR, Slave FLP, Offset 0, Uprate 000, Dnrate 000, SW ID1
Mix 4 - Master GYR, Slave FLP, Offset 0, Uprate -100, Dnrate 100, SW ID2
Flaps with Butterfly (Crow) settings:
Ch5 set to Gear. Inactivate AilDiff.
Mix 1 - Master AIL, Slave AUX1, Offset 0, Uprate 100, Dnrate 100, SW ON
Mix 2 - Master GYR, Slave FLP, Offset 0, Uprate 100, Dnrate -100, SW NOR
Mix 3 - Master GYR, Slave FLP, Offset 0, Uprate -100, Dnrate 100, SW ID1
Mix 4 - Master GYR, Slave FLP, Offset 0, Uprate -100, Dnrate 100, SW ID2
Mix 5 - Master GYR, Slave AUX1, Offset 0, Uprate 100, Dnrate -100, SW ID2
Mix 6 - Master GYR, Slave AIL, SW ID2, Tune L0%, 1,2,3 50%, H100%
If you want to save Mix 5 for another function, use instead:
Mix 7 - Master GYR, Slave AUX1, SW ID2, Tune L100%, 1,2,3 50%, H100%
[NB Mixes 5+6 or 6+7 are set for left Aileron on AIL and right on AUX1]
Up and down Flaperons (glider without flaps):
Ch5 set to Gear. Inactivate AilDiff.
Mix 1 - Master AIL, Slave AUX1, Offset 0, Uprate 100, Dnrate 100, SW ON
Mix 2 - Master GYR, Slave AIL, Offset 0, Uprate 100, Dnrate -100, SW ID1
Mix 3 - Master GYR, Slave AUX1, Offset 0, Uprate -100, Dnrate 100, SW ID1
Mix 4 - Master GYR, Slave AIL, Offset 0, Uprate -100, Dnrate 100, SW ID2
Mix 5 - Master GYR, Slave AUX1, Offset 0, Uprate 100, Dnrate -100, SW ID2
Work out which setting (up or down) works best for your glider then delete the other.
[NB Flaperon should have the same function (with added flap function) but I could not get it to
work.]
I hope all this helps. If anyone knows how to do this more efficiently please post the instructions
and I will remove these.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising