English Instructions PDF

English Instructions PDF
 www.gymboss.com
***Remove protective screen from front of timer.
TURN ON | Push any button.
TURN OFF | Hold SET button for 3 seconds.
After 5 minutes of no use the timer will automatically turn off.
However, if left in stopwatch and clock mode timer will not turn off
on its own.
BUTTON CONFIGURATION
Battery:
• When your battery gets low a battery icon will flash in the bottom right of the screen.
• No Used Batteries Please! We recommend a high quality Energizer or Duracell.
REBOOT a frozen or malfunctioning timer by placing a NEW battery in timer, then using a pen,
push the REBOOT button.
There are 3 modes to the GYMBOSS interval timer.
• CLOCK
• STOPWATCH
• INTERVAL TIMER – allows timing of any one interval, or two different intervals in
sequence. These intervals can then be repeated once, or as many times as you select,
up to 99 times.
To change modes:
• Push the V and Λ buttons at the same time. Learn to recognize each mode on the
screen.
Interval Mode
(1 sec transition flash)
(1 sec transition flash)
Stopwatch Mode
Clock Mode
The setup procedure is similar for all 3 modes. Please learn these key steps:
• Push SET button to enter setup. SETUP must be displayed on the screen to make
changes.
• Use V / Λ to make changes to the flashing digits.
• Each push of SET button will move you to the next step in the setup process.
• When SETUP is no longer displayed, you are no longer in setup and the timer is ready
to use.
The first interval
will be flashing.
SETUP indicates you
Are in SETUP mode.
EXPANDED INTERVAL TIMER MODE SETUP
1. Enter Interval Timer Mode. Every time the timer is turned on it will be in interval timer
mode. If you are in stopwatch or clock mode push the V and Λ buttons at the same time
to enter interval timer mode.
2. Enter SETUP. Push the SET button. SETUP will be displayed indicating you are in
SETUP. NOTE: If no button input within 5 seconds the timer will exit setup and SETUP
will no longer be displayed on the screen.
3. Set your interval times. Push the V or Λ buttons to change the flashing value. Once
done, push SET to move to the next interval time. If you desire to use only one interval,
set the second interval to 00:00. (Zero the 2nd interval or rounds by pushing the V and Λ
buttons together.) Once done, push SET to move to the next step.
4. Choose the number of rounds. (Rounds set from 01-99 will countdown until the selected
number of rounds are completed. Rounds set at 00 will count UP the rounds completed
to 99, or until you stop the timer.) Push the V or Λ buttons to change the flashing value.
Once done, push SET to move to the next step.
5. Choose the Alarm Type. Alarm types are BH (beep high), BL (beep low), V (vibrate) or
any combination of these. Push the V or Λ buttons to change the flashing value. Once
done, push SET to move to the next step.
6. Choose the Alarm Duration. Alarm duration can be set to 1, 2, 5, or 9 seconds. Push
the V or Λ buttons to change the flashing value. Once done, push SET to exit SETUP.
Once SETUP is not displayed, you are no longer in setup. Setup is now complete and
the timer is ready to use.
Interval Timer Mode Setup Tips:
• Backup to previous variable in setup by pushing the START button.
• Hold the V or Λ buttons for fast increase/decrease.
• To Increase/decrease interval time by 10 minutes, Hold V or Λ and push SET.
Interval Timer Mode Operating Tips:
• To stop timing and reset the timer, hold the START button for 3 seconds. Alarm occurs
on reset.
• Pause the timer by pushing the START button 3 times in rapid succession. PAUSE will
be displayed on the screen. Alarm occurs indicating successful pause. Push START to
resume timing. Alarm occurs indicating timing has resumed.
• In PAUSE you can change alarm type and duration. To do this, push SET when in
PAUSE mode.
EXPANDED STOPWATCH MODE SETUP
1. Enter the Stopwatch Mode by pushing the V and Λ buttons at the same time. STOP will
flash momentarily on the screen.
2. Push the SET button. SETUP will be displayed indicating you are in setup.
3. Now you are choosing the Alarm Type. Alarm types are BH (beep high), BL (beep low),
V (vibrate) or any combination of these. Push the V or Λ buttons to change the flashing
value. (NOTE: You can change the alarm type and duration anytime the stopwatch is
not running by pressing the SET button. Push the V or Λ buttons to change the flashing
value. Once done, push SET to exit back to stopwatch.)
4. Once done, push SET to exit SETUP. Once SETUP is not displayed, you are no longer
in setup. Setup is now complete and the stopwatch is ready to use.
5. Push START to start stopwatch. Push START to stop stopwatch. Push the V button to
reset back to 00:00.
EXPANDED CLOCK MODE SETUP
1. Enter the Clock Mode by pushing the V and Λ buttons together. CLOC will flash
momentarily on the screen.
2. Now you are setting the hour and AM/PM. Push the SET button. Push the V or Λ
buttons to change the flashing value. Once done, push SET to move to the next step.
3. Now you are setting the minutes. Push the the V or Λ buttons to change the flashing
value. Once done, push SET to exit Clock setup.
Clock Mode Tips:
• The Clock can be viewed at any time, in any mode, by pressing the Λ button.
HOW TO REMOVE THE BELT-CLIP
1. Turn the timer so that you are looking at the back.
2. Insert your fingernail on latch between belt clip and START button and pull the latch
towards the belt clip while at the same time pushing the belt clip to the right to release. It
will then slide off.
3. If you are still having trouble, please see instructional video on YouTube.
***Lanyard may be attached to timer body next to the START button.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising