Norcon TTU® -1AV - Norcon Communications

Norcon TTU® -1AV - Norcon Communications
®
TTU® -1 AV
•
•
•
•
•
•
•
•
•
•
Norcon TTU® -1AV
Installation & Operating
Instructions
510 Burnside Ave.
Inwood L.I. NY 11096
Tel. 516 239 0300
Fax. 516 239 8915
Introduction ……………………………………...1
Features …………………………………………… 2
How It Works …………………………………… …3
How To Install …………………………………. 4 -6
How To Use The Talk-Thru Communicator ……… 7
Operation Hints …………………………………. . 8
Specifications ……………………………………9-10
Accessories and Options ….…………………….. 11
Troubleshooting …………………………………...13
Warranty …………………………………………..14
Two-way Communication system with security surveillance
camera
A color video camera with pin-hole lens built-in to a
bidirectional communication device used for surveillance.
A voice communications system for High-Security and
Isolation Booth Situations
Today’s security and isolation booths are often the best step
you can take to protect your employees. But do they protect or
help maintain your very important good will? Not if clerks and
customers have to shout and growl and repeat themselves to be
heard or understood.
Norcon’s Patented TTU® -1 Talk-Thru Communicator is
a 2-way, hands-free audio system that provides high-quality
personal communication between people separated by security or
isolation barriers. It is the most widely used system of its type in
the U.S., and the world.
www.norcon.org
HOW IT WORKS …
1
HOW TO INSTALL …
The Norcon TTU® system permits hands-free,
2-way communication between the booth attendant and the
customer. Unique circuitry facilitates ongoing,
clear, 2-way conversation at all times – as if the two
parties were together in the same room.
The TTU®-1 Talk-Thru Communicator now incorporates
circuitry to automatically attenuate the outside channel.
If the gooseneck microphone is not used for a period of
30 seconds, the outside channel volume will be reduced
approximately 70%. Normal operation is restored
as soon as the attendant speaks into the gooseneck
microphone. The automatic volume attenuation circuit
prevents outside noise from bothering the attendant.
The TTU®-1 provides clear communication even in
environments with high ambient noise by shaping
the sound for maximum intelligibility. Its
compression circuitry decreases loud, annoying sounds.
Installation of the TTU® -1 is a very simple, one-person
operation. All that’s needed is a 3” to 4” cutout in the barrier. Four
fasteners and two rubber gaskets for mounting are supplied.
The front face and housing are easily mounted on opposite sides
of the barrier using the fasteners. The rubber gaskets prevent
slippage and protect the barrier surface. The electronic section is
then inserted into the housing and fastened in place.
Installation Instructions
1.
2.
3.
4.
5.
6.
7.
8.
3
FEATURES
Remove the four (4) 6-32 assembly screws.
Separate the housing and electronics assembly. Unplug
electronic assembly from the faceplate and housing.
Set the electronic assembly aside, carefully.
Remove the four (4) 8-32 mounting nuts from the
mounting rods.
Separate the faceplate and housing.
Discard the shipping spacers located between the faceplate
and housing if there are any.
Hold the faceplate over the partition opening. Carefully
center the faceplate and align the lettering horizontally.
Masking tape can be used to temporarily hold the faceplate
to the outside of the partition.
On the inside of the partition mount the housing over
the four (4) 8-32 mounting rods. Be certain to
position the housing so that the threaded hole is
positioned properly. If using tubing, orient the hole in
the direction which the tubing is to exit (left, right,
top, and bottom). If tubing is not being used, place the
plugged hole at the bottom.
4
•
•
•
•
•
•
•
•
•
•
•
A color video camera with pin-hole lens built-in to a
bidirectional communication device used for surveillance.
Clear 2-way hands-free voice communication.
Quality electronic design and engineering.
Avoids shouting, repetition, and misunderstanding.
Simple, one-person installation.
Rugged, tamper-resistant materials. Anodized aluminum
Self-powered with fast rechargeable battery option.
Bullet-resistant option ( UL level 3).
Units available for ADA applications.
Headset jack equipped on all models. Headset can be ordered
separately.
Export models available
2
9.
For power connection, route the one pair cable (with
the connector on one end) FROM the inside unit TO
the location of the PS-1 power supply. Connect the
conductors to the power supply (RED to +, BLACK
to -). Plug the connector to its mate from the printed
circuit board.
10. Connect video output and the audio output to the monitor or
recorder.
11. Connect two 4 –pin polarized connectors and reassemble the
unit.
Be certain to position the
housing so that the
threaded hole can be
positioned properly. If
using tubing, orient the
hole in the direction which
tubing is to exit –
TTU-1AV FACE PLATE
TTU-1AV CONTROL PANEL
5
6
TTU-1 P.1.
HOW TO USE THE TALK-THRU
COMMUNICATOR …
1. With power switch off, turn Talk and Listen controls
completely counter clockwise.
2. Turn on the unit by switching the AUTO MUTE to it’s center
position. In this position, the unit is in the auto mute mode.
3. Adjust the TALK volume control until the attendant is
clearly heard by the person outside the window when the
attendant is speaking 2" to 4" from the gooseneck microphone
at a normal speaking level. The green LED should go on when
the attendant starts talking and go off when the attendant stops
talking. If the green LED stays lit constantly, it indicates either
the TALK volume setting or the ambient noise is too high.
4. Adjust the LISTEN control until the person outside
the window is clearly heard when speaking at a normal level.
OPERATION HINTS
MECHANICAL SPECIFICATIONS
1. Increasing the talk volume control allows the attendant to speak
further from the microphone as well as increasing the talk
channel volume. The optimum distance from the microphone
should be maintained at approximately 3” or conversations not
directed to customers may be heard outside the booth. Watch
the green LED above the TALK volume control, it should be
on ONLY when talking into the gooseneck microphone.
2. Installing a headset into the Headset jack will allow
communications from the headset and disconnect the speaker
and the gooseneck microphone.
3. The unit will decrease the incoming volume level by
approximately 70% some 30 seconds after the attendant stops
speaking into the microphone. The purpose of this feature is to
decrease the amount of extraneous noise entering the booth.
Normal volume level is restored when the attendant speaks into
the microphone. The muting function can be defeated by
switching the AUTO MUTE switch to the OFF position.
•
•
•
•
•
•
ELECTRONIC SPECIFICATIONS
•
Outside faceplate: Solid aluminum, anodized finish,
tamper-resistant.
Control housing (inside): Machined aluminum, anodized
finish, tamper-resistant.
Size: Outside faceplate 5” Dia. x ½” D.
Inside control housing:
5” Dia. x 2-1/2” D)
Weight: ~ 5 LB.
Mounting: Partition hole 3 to 4” Dia. ( 3-1/2” recommended)
Specify barrier thickness when ordering. Norcon will adjust
the length of the mounting rods to meet your need.
Panel Controls:
LISTEN volume, TALK volume
POWER On/Off , AUTO MUTE On/Off.
•
•
•
•
•
Audio frequency response: Selectively shaped for maximum
voice intelligibility.
Audio power: 2 watts per amplifier.
Distortion: Less than 2%.
Listen mode: 20dB compression.
Microphone: Electret.
Power Supply: Input – 120V AC, 60 Hz. Output 15V DC,
200mA.
(220V version for export also available)
Specifications are subject to change without notice.
MADE IN U.S.A.
TALK
INDICATING LED
7
CCD Color Camera Technical Specification
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Image Sensor
Effective Number of Pixels
Resolution
Output Signal
Lens
View Angle
Signal Processing
Sensitivity
S/N
AGC
Electronic Shutter
White Balance
Gamma Correction
Synchronization
Power Consumption
Operation Temperature
Operating Humidity
¼” 270k Pixel T-CCD
512(H) x 492(V) pixels
Horizontal 330 TV line
NTSC Video
Pinhole Lens: F3.5, f=37mm
D: 68° H: 54° V: 40°
DSP 8bit/ A/D , 10 bit D/A
10 Lux
46 dB
6 dB
1/60sec – 1/100sec. Auto
Auto
0.45 Typ
Internal Synchronization
DC 4.0V, 140mA
14°F - 122°F (-10° C -+50°C)
10% - 90%, RH
Note:
A person placing an order for a TTU-AV unit from Norcon Communications, Inc.
warrants that he or she is an adult of legal age the products purchased will be used only
in a lawful manner. As we are solely the manufacturer of the product, we have no control
over the use of the TTU-1AV unit once it is in the buyer’s possession and we assume no
liability associated with their use. Because local laws, safety standards and regulations
vary, we cannot guarantee that the products purchased hereunder meet all application
requirements in each locality. It is the responsibility of the buyer to ascertain and obey
all applicable local, state, federal laws in regard to the possession and use of the TTU1AV unit in localities in which the product is shipped, sold and used. Under no
circumstances will Norcon Communications, Inc. or any of its affiliates be liable for any
loss, damage or expenses of any kind arising out of the use, inability to use or misuse of
these products.
11
9
8
Accessories and Options for TTU®
HS Headset (Option)
• Superior sound quality
• Long wearing comfort
TROUBLESHOOTING
You may occasionally encounter a problem with your
TTU® system. If this happens, refer to the following list. If
additional help is needed, please contact us.
1.
•
No sound at all
Is the power supply properly plugged into a working
outlet ?
If the power supply has been plugged into a working outlet
for a while, the power supply should be warm, if it is not; the
power supply may be defective.
Professional Wireless Headset System (Option)
•
•
•
Mobile: DETC 6.0 technology hand-free mobile
design with range of up to 300 feet from base unit
DuoSet Headset: Adjustable for over-the-head
stability or over-the –ear convenience with new
conformable earloop
Extended Use: Ten hours continuous talk time on
rechargeable battery.
10
2.
•
Howling ( Feed back)
Is the TALK or LISTEN volume turned too high?
Set the volume control to a proper level. In most cases, both
TALK and LISTEN should be set to the position of around 11
to 12 o’clock.
3.
•
Conversation cutting-off and breaking-up
Is the TALK volume setting too high?
Turn down TALK volume to a proper level.
•
Is the attendant talking too far from the gooseneck
microphone?
The idea distance is 3” to 4” from the gooseneck microphone.
Service Policy
TALK-THRU SYSTEM WARRANTY REPAIRS
Norcon Communications Inc. warrants the products
Manufactured by Norcon to be free from defects in
material and workmanship for a period of one year
from the date of shipment from the factory provided:
1) The product has not been abused, misused or
improperly maintained, repaired and /or modified during
such period, and 2) such defect is not a result of voltage
surges/ burnouts, lightning, water damage / flooding, fire,
explosion, earthquakes, tornadoes, acts of aggressions /
war or similar phenomenon; and 3) the product has been
properly installed according to the appropriate Norcon
Installation Guide.
Both incoming and outgoing freight charges are at customer’s
expenses. Domestic repair will be returned to customer by UPS
Ground. International repair will be returned to customer using
normal shipping arrangements. Any other shipping instructions
must be made in writing and will be at the customer’s expense.
*
12
13
Extended two years warranty available.
Please call 1-866-239-0300.
14
TTU-1- 061027
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising