AudioCodes 310HD Server Setup Guide

AudioCodes 310HD Server Setup Guide
AudioCodes 310HD
and Elastix Server
Setup Guide
http://www.elastix.org
PaloSanto Solutions
AudioCodes 310HD Server Setup Guide
1.0 Setup Diagram
Figure 1-1 is a setup diagram for a single IP Phone AudioCodes 310HD configuration. The
phone is setup as a SIP telephony device.
Figure 1-1. Setup Diagram
2.0 Host PC Environment
Table 2-1. Host Server Environment Details
Hardware Type
Hardware Version
Software Type
Software Version
Description
Elastix Appliance ELX-Series
ELX-3000
Elastix
2.3
3.0 Test Setup Equipment
Table 3-1. Test Setup Equipment
Equipment
IP (SIP) Phone
AudioCodes
Switch
Model
N/A
310HD
N/A
2
Version
N/A
1.4.0_build_28
N/A
PaloSanto Solutions
AudioCodes 310HD Server Setup Guide
4.0 Setup Procedure
To set up the Elastix Server for the AudioCodes 310HD,
1. Go to the web address of the Elastix Server Login page. The web address is
determined by the customer, for this guide we have used the IP address 192.168.1.65
2. On the Login page, type the username and password for an administrative user into
the Username and Password fields, see Figure 4-1. The username and password are
determined by the customer.
Figure 4-1. Login
3. Press Enter or click on the Submit button to go to Elastix’s Dashboard
4. Once inside, click on the PBX tab on the menu at the top of the screen
Figure 4-2. Dashboard
3
PaloSanto Solutions
AudioCodes 310HD Server Setup Guide
5. Click on the Submit button to add an extension, see Figure 4-3. This will take you to
the Add SIP Extension page.
Figure 4-3. Add an Extension
6. On the Add SIP Extension page (Figure 4-4), fill in the following information:
• User Extension (301 in this example)
• Display Name (‘AudioCodes310HD’ in this example)
• secret (‘h7Dka3Rf9si0t’ in this example)
Figure 4-4. Add SIP Extension
4
PaloSanto Solutions
AudioCodes 310HD Server Setup Guide
7. Click on the ‘Submit’ button at the end of the page. The extension will be created and
you will see the page on Figure 4-5 displaying the “Apply Configuration Changes Here”
pink ribbon on top of the screen.
8. Click in the “Apply Configuration Changes Here” link
Figure 4-5. Apply Configuration Changes Here
9. With this you have just finished creating a SIP extension that will be used by the
AudioCodes 310HD to register with the Elastix Server. Repeat Steps 5 through 8 to
similarly create another extension (different values on Step 6) to be used by the IP (SIP)
Phone to register as well (extension 302 in this example). Once finished you will see
something similar to Figure 4-6
Figure 4-6. AudioCodes and IP Phone extensions successfully created
10. You will need to enter the information from the extension created on the Elastix
Server into the AudioCodes Phone.
For the initial configuration, refer to the AudioCodes 310HD Administration Guide
which can be found at: http://www.audiocodes.com/products/310hd
Factory default settings
IP Addressing
DHCP
Web Access User Name admin
Web Access Password
1234
11. Log in to the AudioCodes 310HD WebUI by pointing your browser to the
AudioCodes Phone’s IP address.
12. When prompted, enter the Web Access Username and Web Access Password to
access the AudioCodes WebUI (Figure 4-7).
5
PaloSanto Solutions
AudioCodes 310HD Server Setup Guide
Figure 4-7. AudioCodes 310HD WebUI
To register the AudioCodes Phone we have two methods: Manual Configuration or
AutoProvisioning using Elastix’s Endpoint Configurator.
6
PaloSanto Solutions
AudioCodes 310HD Server Setup Guide
MANUAL CONFIGURATION
1. Use the information from the Add SIP Extension page (Figure 4-4) to enter the
following necessary information on “Quick Setup“ section of the AudioCodes Phone
WebUI:
SIP Proxy and Registrar
 Use SIP Proxy: Enable
 Proxy IP Address or Hostname: Elastix Server’s IP Address (192.168.1.65 in
this example)
 Proxy Port: 5060
 Use SIP Proxy IP and Port for Registration: Enable
Line Settings
 Line Activate: Enable
 User ID: (301 in this example)
 Authentication User Name: (301 in this example)
 Authentication Password: (‘h7Dka3Rf9si0t’ in this example)
Figure 4-8. Account Configuration
2. Once you have entered the required information, click on ‘Submit’ button located at
the end of the page. If the phone is not able to register, make sure you’ve entered the
correct information.
3. Configure the other IP (SIP) Phone with the correct parameters.
4. To test the AudioCodes 310HD, pick up the previously configured IP (SIP) Phone
and call the AudioCodes 310HD’s extension number (301 in this example). When the
call is established, speak into the phone and verify that the other IP (SIP) Phone can
hear your voice. Check this by calling from both ends.
This step completes the manual procedure.
7
PaloSanto Solutions
AudioCodes 310HD Server Setup Guide
AUTOPROVISIONING USING ELASTIX’S ENDPOINT
CONFIGURATOR
1. In the AudioCodes 310HD WebUI, go to “Management => Automatic Update”.
Copy apart the “Configuration URL” (Figure 4.9) and replace the
PovisioningServer by Elastix’s IP Address, and the ‘/’ character from the cfg file
with ‘_’, something like this:
tftp://192.168.1.65/310HD_00908f1ee105.cfg
Figure 4.9 Automatic Update
2. Set the following parameters (Figure 4.10):



Provisioning Method: Static URL
Configuration URL: tftp://192.168.1.65/310HD_00908f1ee105.cfg in this
example
Check Period: On Power-up Only
Figure 4.10 Automatic Update
3. Click on “Submit” button. Now, in the Elastix WebUI go to “PBX => Endpoint
Configurator” (Figure 4-11).
Figure 4.11 Endpoint Configurator
8
PaloSanto Solutions
AudioCodes 310HD Server Setup Guide
4. Next to the “Discover Endpoints in this Network” button, type the address where
the phone is located and hit Enter (or click the button). This will generate a list with
all the phones available in that network (Figure 4-12).
Figure 4.12 Endpoint Configurator
5. In the row where the phone you want to autoprovision is located (find it according
to either its MAC or IP Address):



Mark the checkbox
From the drop-down list, select the correct “Phone Type” (phone model) of the
phone
From the drop-down list, select the “User Extension” you want to assign to the
phone
Figure 4.13 Endpoint Configurator
6. Click the “Set” button. When the process finish loading, reboot the phone by
unplugging and plugging again the power cord.
7. If you refresh the page after phone reboot, you should see the extension number in
9
PaloSanto Solutions
AudioCodes 310HD Server Setup Guide
the “Current Extension” field (Figure 4.14). The phone should be registered and
ready for calls now.
Figure 4.14 Endpoint Configurator
8. Configure the other IP (SIP) Phone with the correct parameters.
9. To test the AudioCodes 310HD, pick up the previously configured IP (SIP) Phone
and call the AudioCodes 310HD’s extension number (301 in this example). When
the call is established, speak into the phone and verify that the other IP (SIP) Phone
can hear your voice. Check this by calling from both ends.
10
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising