6" REMOTE CONTROL SEARCHLIGHT MODELS 63020, 63022

6" REMOTE CONTROL SEARCHLIGHT MODELS 63020, 63022
MODELS 63020, 63022, 63042
Models 63020, 63022, 63042
6" REMOTE CONTROL
SEARCHLIGHT
FEATURES
• Complete drive unit contained in light head.
• Single lever or touch-pad control for vertical and
horizontal light movement.
• Two speed light movement.
• Auto-sweep mode cycles light side-to-side
automatically.
• Light will transmit an “SOS” distress signal
automatically.
• Designed for salt water with chrome brass housing
and base.
• Control is water resistant with plug-in connections.
• Two station operation optional with use of dual
station kit.
63020
• Two types of light output:
- Spot/flood sealed beam bulb, 200,000/50,000
candlepower.
- Spot beam high intensity discharge bulb, 600,000
candlepower.
Model Voltage Beam
63020-0012 12/24 Spot/Flood
63022-0012 12/24 Spot/Flood
63022-1224 12/24 Spot/Flood
63042-1224 12/24
HID Spot
Base
Chrome Zinc-Short
Chrome Brass-Tall
Chrome Brass-Tall
Chrome Brass-Tall
Lights include control and 15' cable from control to
light. Extension cables can be used to increase cable
length.
ACCESSORIES
Extension Cables
With Plugs
Bulk Cable
No Plugs
Part Number Length Part Number Length
64042-1011
10'
64043-0100
100'
64042-1007
15'
64043-0250
250'
64042-1008
25'
64043-0500
500'
64042-1009*
50'
64043-1000
1000'
63022 AND 63042
Control and 15' cable
included with light
* This is heavy gauge wire required for runs of 50'.
Dual Station Kit #64044-0000 Includes control,
Y-adaptor and 15' cable. Use for boats with two control
locations.
Cable Plug Kit #64045-0000 Includes male/female
plugs with 2' cable for connecting to bulk cable.
Dual station kit #64044-0000
LIGHT MOUNTING
Light should be mounted forward of the operator’s
position on the boat. Use the base mounting gasket as a
template to drill mounting holes. A 7/8" (20mm) hole is
required to pass the cable plug. The short base has a
line on the mounting flange to indicate the forward
positioning of the light. The cable plug can be pushed
below the mounting into the hole or pushed into the base
of the tall base model lights. The cable is routed through
the boat to the control location.
CONTROL MOUNTING
1. Select a location near the helm position to mount the
control. Check under the mounting area to assure
there is adequate clearance for the control.
2. Cut 2-3/4" (70mm) diameter hole for the control and
drill two holes for the mounting screws.
3. Power to control must be controlled by the boat
running light switch. The searchlight control has LED
illumination that will go on with the boat running
lights. The searchlight can only be used with the
running lights on. The running light circuit must be
capable of carrying the following amperage load in
addition to the running lights and have a fuse or
circuit breaker of appropriate size:
Bulb Type
Spot/Flood Sealed Beam
Spot/Flood Sealed Beam
High Intensity Discharge
High Intensity Discharge
Voltage
12
24
12
24
Amperage
15
15
15
20
4. Connect the RED control power lead to the switched
side of the running light circuit. Connect the BLACK
control power lead to a battery negative source. DO
NOT connect in reverse polarity, as control damage
will result. Use 12–14 gauge wire to extend power
leads if necessary.
5. Bring power leads and light cable through hole and
plug into back of control.
6. To eliminate electrical interference produced by
other electronic components on the boat that might
affect the searchlight control, route the searchlight
control cable to the light away from other components such as radios, GPS receivers and other
navigation units.
7. Insert control with attached cables into hole and
fasten with screws. A non-adhesive sealing compound
should be used under the control mounting flange.
8. For joy-stick type of control, thread black lever into
center hole. For touch-pad operation, insert black
cap into threaded hole.
LIGHT OPERATION
IMPORTANT — Do not shine the searchlight in any
manner that will impair the vision of other boat operators.
The running light switch for the boat must be “on” for
searchlight to operate. With the running light switch “on”,
the searchlight control will be illuminated.
SPOT/SLOW — Press once to select slow light movement speed and, on spot/flood type lights, to select spot
beam. Press again to turn light off.
FLOOD/FAST — Press once to select fast light movement speed and, on spot/flood type lights, to select flood
beam. On lights with spot beam only, this button selects
the fast speed only. Press again to turn light off.
DIRECTIONAL MOVEMENT — The center lever is
moved left, right, fore and aft to move light head. If
desired, the center lever can be unscrewed (counterclockwise) and the black cap (supplied) can be pressed
into the center hole. The light movement is then controlled by touching one of the four arrows.
AUTO SWEEP — With the light on, pushing this button
will sweep the light in about a 90 degree arc automatically. This is useful in narrow canals and channels,
freeing both hands for boat control. Press again to stop
auto sweep.
SOS/DISTRESS — Press and hold for about five
seconds to automatically flash “SOS” in International
Morse Code. The light will sweep horizontally while
flashing the SOS. Press again to stop the SOS flashing.
IMPORTANT — Do not allow anyone to “playfully”
transmit the SOS signal! The SOS signal will not be
transmitted with the boat’s running lights “off”.
CIRCUIT PROTECTION
The searchlight control has built-in circuit breaker
protection for the searchlight. The breaker can be reset
by turning the light on then off with the running lights on.
On 24VDC lights, do not operate the light at less than
18 volts. Turn off the light before recharging battery.
DUAL STATION CONTROL (OPTIONAL)
The optional Dual Station Control Kit #64044-0000 is
used when an additional searchlight control location is
desired.
1. Install control in the dual station kit as covered in the
“Control Mounting” section of these instructions.
2. Using the 15' cable and Y adaptor included in the
dual station kit, connect the cable into the light
control cable.
Optional extension cables may be used where necessary to fit the application. Also, the 3 conductor cable
may be cut and spliced together if too long.
EXPLODED VIEW
7
8
8
3
4
5
2
9
1
Key
No.
1
2
3
4
5
6
7
8
9
Part Description
Base (includes gasket and set screws)
Tall Brass Chrome
Short Zinc Chrome
Housing
Motor/Support Assembly
12VDC and 24VDC
12 VDC for HID
24 VDC for HID
Bulb Retaining Ring, Screw and Nut
Spot/Flood Bulb and Seal
12VDC and 24VDC
HID Bulb
12 VDC
24 VDC
HID Lens, Reflector and Seal
HID Ballast & Connector (12/24) VDC
Control
63020-Series
Part No.
Qty.
63022-Series
Part No.
Qty.
63042-Series
Part No.
Qty.
–––
63130-0000
64046-0001
–
1
1
64046-0000
–––
64046-0001
1
–
1
64046-0000
–––
64046-0001
1
–
1
64046-0002
–––
–––
64046-0005
1
–
–
1
64046-0002
–––
–––
64046-0005
1
–
–
1
–––
64046-0003
64046-0004
64046-0005
–
1
1
1
64046-0006
1
64046-0006
1
–––
–
–––
–––
–––
–––
43690-1000
–
–
–
–
1
–––
–––
–––
–––
43690-1000
–
–
–
–
1
64046-0007
64046-0007
64046-0009
64046-0010
43690-1000
1
1
1
1
1
63020 SERIES
63022 AND 63042 SERIES
THE PRODUCTS DESCRIBED HEREIN ARE SUBJECT TO
THE JABSCO ONE YEAR LIMITED WARRANTY, WHICH IS
AVAILABLE FOR YOUR INSPECTION UPON REQUEST.
www.xylemflowcontrol.com
Jabsco is a trademark of Xylem Inc. or one of its subsidiaries.
© 2012 Xylem, Inc. 43000-0728 Rev 5/12
Jabsco, 1 Kondelin Road, Cape Ann Industrial Park, Gloucester, MA 01930
Tel: +1 978 281 0440
Fax: +1 978 283 2619
USA
Jabsco, Bingley Road, Hoddesdon, Hertfordshire, EN11 0BU
Tel: +44 (0) 1992 450 145
Fax: +44 (0) 1992 467 132
UK
NHK Jabsco Co Ltd, 3-21-10, Shin - Yokohama Kohoku-ku, Yokohama 222
Tel: +81 (0) 45 475 8906
Fax: +81 (0) 45 475 8908
JAPAN
Jabsco GmbH, Oststraße 28, 22844 Norderstedt
Tel: +49 (0) 40 53 53 73 0 Fax: +49 (0) 49 53 53 73 11
GERMANY
Jabsco Italia, s.r.l., Via Tommaseo, 6, 20059 Vimercate, Milano
Tel: +39 039 685 2323
Fax: +39 039 666 307
ITALY
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising