Turnigy B6 Compact 50W 5A
 т bh LiPo Battery Charger TURNIGY.
INSTRUCTION MANUAL fi
(DM
Thank you for your choice of the Turnigy B6, 11-18V DC LiPo Battery charger. This unit is simple to use
but its operation does require some knowledge on the part of the user. Please read this entire operating
manual completely and attentively before using this product, as it covers a wide range of information on
operating and safety.
Turnigy B4 Charger is an economic, high quality 11-18V DC balance charger with max circuit 50W and
max charge current 5A, designed for charging 1-6S LiPo batteries in balance mode. The charging current
will be adjusted automatically according to the capacity detected by the charger.
Cell 1 LED Indicator a
DC 11-18V
Cell 2 LED Indicator se = Ro
LA N
Power Jack
Cell 3 LED Indicator
в
Cell 6 LED Indicator
Cell 5 LED Indicator
Battery Socket
Cell 4 LED Indicator
2-6S Balance
(| CHARGE PROCEDURES 3
Please refer to following steps to charge the battery, We Suggest Adaptor:
1) Connect Turnigy B6 charger to an AC adaptor and insert the 60W Power Supply (20968)
AC adaptor into a wall socket. All LEDS will flash green,
indicating the charger is ready to work.
Note: It requires an AC adaptor with minimum power 60W and
voltage DC11-18V.
2) Connect the battery main charge lead to battery socket of the
charger and battery balance wire to balance port. For 1S
battery, just connect the battery main charge lead to battery
socket.
3) The charger will detect the battery voltage and start to charge with CC mode and the cell status LED
will glow constant red. If the battery pack is 2-cell, Cell 1 and Cell 2 LEDS will glow constant red; if the
a 4) During the charging process, the charger will detect
the battery capacity and take the most suitable current
to charge the battery until it is fully charged.
5) During the charging progress, when the cell status
LED glows constant red, the charger is charging in CC RS
mode; when the cell status LED glows constant LA SUEUR
orange, the charger is charging in CV mode.
6) When the battery is fully charged, the cell status LED
glows constant green
7) Unplug the battery from the charger and the cell status #9 Battery
LED will flash green which indicates the charger is 8
ready to charge another battery.
Note: During the charging process, if the battery
balance wire is disconnected from the charge balance
port, the charge process will stop. But if the battery
main charge lead is disconnected from the battery
socket, the red LED will blink once with 1 beep for 5
times, indicating error message “Battery not connect” .
CONNECTION DIAGRAM
A\ CAUTION:
This diagram shows the correct way to connect your battery to the B6 charger while charging in balance mode.
Socket
A J
Failure to connect as shown in this diagram will damage this charger.
N
N
f[ EXPLANATION OF LED STATUS
Cell Status LED 5 Charger Status
LED green blinking The charger is ready to charge.
LED glows constant red The charger is charging in CC mode.
LED glows constant orange The charger is charging in CV mode.
LED glows constant green. The charging process finishes.
LED flashes red Error Message.
* Error Message
Error Message Problem
Red LEDS blink once with 1 beep 5 times Battery not connect
Red LEDS blink twice with 2 beep 5 times Reverse polarity
Red LEDS blink three times with 3 beep 5 times | One cell of the battery voltage higher than 4.3V
Red LEDS blink four times with 4 beep 5 times | Input voltage higher than 18V
Red LEDS blink five times with 5 beep 5 times Input voltage lower than 11V
battery pack is 3-cell, Cell 1, Cell 2 and Cell 3 LEDS will glow constant red; and so on. 5
1-
A
Red LEDS blink six times with 6 beep 5 times Over current (>5.5A), over load or short circuit protection
N
SPECIFICATION
e DC Input: 11-18V e Battery Type: LiPo e Cell Count: 1-6 cells
e Charge Current: Max. 5A e Cell Terminate Voltage: LiPo: 4.2V + 0.02V
e Circuit Power: 50W e Current Drain for Balancing: 200mA
e Protection: Short Circuit, Over Current, Polarity Reverse
e Dimension: 77.8x116.7x31mm e Weight: 127g
SE
THE SET CONTAINS
O Turnigy B6 LiPo Battery Charger
O Alligator Clip Charging Connector
O Charging Cable with XT60 Connector
/ Ty
WARRANTY AND SERVICE
We guarantee this product to be free of manufacturing and assembly defects for a period of one year from the time of
purchase. The warranty only applies to material or operational defects, which are present at t he time of purchase.
During that period, we will repair or replace free of service charge for products deemed defective due to those causes.
You will be required to produce proof of purchase (invoice or receipt). This warranty is not valid for any damage or
subsequent damage arising as a result of misuse, modification or as a result of failure to observe the procedures
/ ЕТ EXCLUSION
This charger is designed and approved exclusively for use with the types of battery stated in this Instruction Manual.
Hextronik accepts no liability of any kind if the charger is used for any purpose other than that stated.
We are unable to ensure that you follow the instructions supplied with the charger, and we have no control over the
methods you employ for using, operating and maintaining the device. For this reason we are obliged to deny all liability
for loss, damage or costs which are incurred due to the incompetent or incorrect use and operation of our products, or
which are connected with such operation in any way.Unless otherwise prescribed by law, our obligation to pay
compensation, regardless of the legal argument employed, is limited to the invoice value of those Hextronik products
which were immediately and directly involved in the event in which the damage occurred.
= J
| WARNING AND SAFETY NOTES ES
e This charger is not intended for use by persons (include children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do
not play with the appliance.
e If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similar qualified persons
in order to avoid a hazard.
e This charger is suitable for charging rechargeable LiPo batteries. Do not attempt to recharge non-rechargeable
batteries. Charging other types of batteries may cause fire or explosion.
e Never leave the charger unattended when it is connected to its power supply.
e Protect charger from dust, dirt and damp.
e Never place the charger and batteries connected to it on any form of flammable surface. Never operate the charger
in the vicinity of inflammable material or gas.
e During charging, the battery must be placed in a well ventilated area . Never place the charger on a carpet or similar
surface.
e Take great care to maintain correct battery polarity, and avoid shot-circuit. Read the battery manufacturer's
instructions and adhere to them strictly.
e The charger must only be plugged into an earthed socket-outlet (for portable class 1 battery chargers for outdoor
use)
e The connection to the supply mains is to be in accordance with the national wiring rules when battery chargers for
installation in caravans and similar vehicles.
\_ oulines in this manual. +
AA
WARNING! FIRE HAZARD!
NEVER USE CHARGER UNSUPERVISED!
«Batteries pose a SEVERE risk of fire if not properly handled.
*Read Entire operation manual before using charger.
* This unit may emit heat during use.
«Only operate this device in a cool ventilated area away from flammable objects.
\ Faire to observe safety procedures may cause damages to property or injury.
Y TURNIGY,
power systems
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising