T400A/W, MCD400A/W, R400A/W, MFD400A/W, D400A/W Ice

T400A/W, MCD400A/W, R400A/W, MFD400A/W, D400A/W Ice
T400A/W, MCD400A/W, R400A/W,
MFD400A/W, D400A/W Ice Machines
Installation, Operation and Service Manual
Serial numbers above D25455
Following installation, please forward this manual
to the appropriate operations person.
801 Church Lane • Easton, PA 18040, USA
Toll free (877) 612-5086 • +1 (610) 252-7301
www.follettice.com
Order parts online:
www.follettice.com
208600R22
2
T400A/W, MCD400A/W, R400A/W, MFD400A/W, D400A/W Ice Machines
Table of contents
Welcome to Follett Corporation............................................................................................................................ 4
Specifications......................................................................................................................................................... 5
Installation............................................................................................................................................................... 8
Top mount ice machines (models T400A/W, MCD400A/W and MFD400A/W)............................................... 8
RIDE® model ice machines (models MCD400A/W, R400A/W)....................................................................... 9
Ventilation............................................................................................................................................... 14
Ice transport tube................................................................................................................................... 15
Start up................................................................................................................................................... 17
Cleaning/descaling and sanitizing...................................................................................................................... 17
Weekly........................................................................................................................................................... 17
Monthly.......................................................................................................................................................... 18
Semi-annually............................................................................................................................................... 18
Service................................................................................................................................................................... 19
Ice machine operation................................................................................................................................... 19
Technical specifications................................................................................................................................. 20
Refrigeration system diagram................................................................................................................. 20
Refrigeration pressure data.................................................................................................................... 20
Compressor data.................................................................................................................................... 20
Gearmotor data...................................................................................................................................... 21
MCD400A/W wiring diagram.................................................................................................................. 21
Electrical control system operation................................................................................................................ 22
Refrigeration system..................................................................................................................................... 28
Service procedures....................................................................................................................................... 29
Evaporator disassembly......................................................................................................................... 29
Evaporator reassembly........................................................................................................................... 29
Gearmotor replacement......................................................................................................................... 29
Troubleshooting.................................................................................................................................................... 30
Replacement parts............................................................................................................................................... 32
T400A/W, MCD400A/W, R400A/W, MFD400A/W, D400A/W Ice Machines3
Welcome to Follett
Follett equipment enjoys a well-deserved reputation for excellent performance, long-term reliability and outstanding
after-the-sale support. To ensure that this equipment delivers that same degree of service, we ask that you review
the installation portion of this manual before beginning to install the unit. Our instructions are designed to help you
achieve a trouble-free installation. Should you have any questions or require technical help at any time, please call
our technical service group at (877) 612-5086 or +1 (610) 252-7301.
Note: To expedite assistance, all correspondence or communication MUST include the model number, serial number
and complete and detailed explanation of the problem.
Before you begin
After uncrating and removing all packing material, inspect the equipment for concealed shipping damage. If damage
is found, notify the shipper immediately and contact Follett Corporation so that we can help in the filing of a claim,
if necessary.
Check your paperwork to determine which model you have. Follett model numbers are designed to provide
information about the type and capacity of Follett equipment. Following is an explanation of the different model
numbers in the
400 series.
MCD400ABT
Configuration
Application
Condenser type
Ice machine capacity and refrigerant
400 – 400 lbs (181kg)/day, R404A
A – air-cooled
W – water-cooled
S – RIDE®
T – top-mount
V – Vision
B – Bin
H – Harmony
Voltage
D – 115V 60Hz
Ice machine series
Nugget ice machine
MCD – RIDE model installation, Vision™ ice and beverage dispensers and top installation, Follett ice storage bins
R – Remote installation, Symphony™ ice and water dispensers
D – Replacement icemaker, Symphony ice and water dispensers
Flake ice machine
MFD – Top installation, Follett ice storage bins
!
Important cautions
Moving parts. Do not operate with front cover removed.
Hot parts. Do not operate with cover removed.
To reduce risk of shock disconnect power before servicing.
Most ice machine cleaners contain citric or phosphoric acid, which can cause skin irritation. Read caution label
on product and follow instructions carefully.
Ice is slippery. Maintain counters and floors around dispenser in a clean and ice-free condition.
Ice is food. Follow recommended cleaning instructions to maintain cleanliness of delivered ice.
4
T400A/W, MCD400A/W, R400A/W, MFD400A/W, D400A/W Ice Machines
Specifications
Electrical
§§ Each ice machine and dispenser require a separate circuit with electrical disconnect within 10 ft (6m).
§§ Equipment ground required.
§§ Standard electrical – 115 V, 60 Hz, 1 phase.
§§ Maximum dispenser fuse – 15A,
§§ Maximum ice machine fuse – 20A each
§§ Maximum ice machine amperage – 11A each
§§ Cord and plug provided on ice machine and dispenser
Electrical connections
Model
25FB400A/W, 50FB400A/W, 110FB400A/W
25CT400A/W, 50CT400A/W, 110CT400A/W
25CR400A/W, 50CR400A/W, 110CR400A/W
Electrical connection
Circuits required
cord & plug provided
115/60/1, 20A max. fuse size
cord & plug provided
115/60/1, 20A max. fuse size
dispenser, ice machine
and bin signal:
cord & plug provided
115/60/1, (2) circuits required
dispenser: 15A max. fuse size
ice machine: 20A max. fuse size
VU155R400A/W, VU300R400A/W
VU155BR400A/W, VU300BR400A/W
VU155R400A/WX, VU155BR400A/WX
dispenser, ice machine
and bin signal:
cord & plug provided
115/60/1, (2) circuits required
dispenser: 15A max. fuse size
ice machine: 20A max. fuse size
VU155NR400A/W, UD300R400A/W
VU155R800A/W, VU300R800A/W,
VU155R800A/WX,
VU155BR800A/W, VU300BR800A/W,
VU155R800A/WX
dispenser, ice machine
and bin signal:
cord & plug provided
115/60/1, (3) circuits required
dispenser: 15A max. fuse size
ice machine: 20A max. fuse size
CAUTION!
§§ Check start relay before supplying power.
§§ Start relay is gravity sensitive and MUST be in "up" position.
§§ Failure to comply may cause equipment to overheat, resulting in equipment failure, equipment damage or a
fire hazard.
UP
UP
UP
top mount and
RIDE model position
freestanding
position
T400A/W, MCD400A/W, R400A/W, MFD400A/W, D400A/W Ice Machines5
Plumbing
§§ 3/8" OD push-in water inlet
§§ 3/4" MPT drain
§§ 3/8" FPT condenser inlet (water-cooled condenser only – 1.25 gpm minimum available flow)
§§ 3/8" FPT condenser drain (water-cooled condenser only)
Notes:
§§ Slope to drain of 1/4" per foot (6 mm per 30.4 cm run) with a 1/2" min. is recommended.
§§ Water shut-off recommended within 10 feet (3 m), drain to be hard piped and insulated.
§§ Separate drains for ice machine and condenser. To prevent back flow, do NOT connect drains.
§§ Follett recommends a Follett water filter system be installed in the ice machine inlet water line (standard capacity
#00130299, high capacity #00978957, carbonless high capacity #01050442).
Ambient
Air temperature
100 F/38 C max.
50 F/10 C min. (best performance below 80 F/27 C)
Water temperature
90 F/32 C max.
40˚F/4˚C min. (best performance below 70 F/21 C)
Water pressure
70 P.S.I max. (482 kPA)
10 P.S.I. min. (89 kPA)
6
T400A/W, MCD400A/W, R400A/W, MFD400A/W, D400A/W Ice Machines
Dimensions and clearances
§§ Entire front of ice machine must be clear of obstructions/connections to allow removal.
§§ 12" (30.5 cm) clearance above ice machine for service.
§§ 6" (15.3 cm) minimum clearance between exhaust side of ice machine and any adjacent equipment.
§§ MCD400A & R400A – 18" (45.7 cm) minimum, 10 ft (3 m) maximum clearance between discharge and air
intake grilles.
Back view — air-cooled
top mount
Front view — air-cooled
top mount
13.00"
(33.1 cm)
C
4.875"
(12.4 cm)
2.375"
(61 mm)
B
A
Front view — water-cooled
RIDE model
Back view — water-cooled
top mount
Front view — air-cooled
RIDE model
C
12.875"
(32.7 cm)
F
8.375"
(21.3 cm)
B
4.75"
(12.1 cm)
2.25"
(57 mm)
A
1.875" (48 mm)
C
F
D
B
E
A
6.875"
(17.5 cm)
2"
(51 mm)
1.875" (48 mm)
7.00" (17.8 cm)
Side view — air-cooled and water-cooled
top mount and RIDE model
Ice machine plug
configuration
NEMA 5-20
22.75" (57.8 cm)
20.75" (52.7 cm)
17.00"
(43.2 cm)
RIDE model air-cooled units only
A – 3/4" MPT drain
B – 3/8" OD push-in water inlet
C – Electrical cord
D – 3/8" FPT condenser inlet
E – 3/8" FPT condenser drain
F – Bin signal cord
T400A/W, MCD400A/W, R400A/W, MFD400A/W, D400A/W Ice Machines7
Installation
Ice machine performance is very sensitive to the quality of installation. To ensure proper performance, ease of
service and warranty coverage, it is critical that you follow the requirements detailed in this manual. If you cannot
meet these requirements or have questions, call our technical service group immediately at (877) 612-5086 or
+1 (610) 252-7301.
Top mount ice machine on bin installation procedure (models MCD400A/WBT and MFD400A/WBT)
Install ice machine and rough-in utilities
1. Install ice storage bin in its final location.
2. Install one supplied grommet in large knockout in base of ice machine and second supplied grommet in ice
hole provided in top of ice storage bin.
3. Rough in plumbing and electrical per specifications provided.
4. Flush all water lines before final hook up.
5. Position ice machine with utility connections facing rear of bin.
§§ If new storage bin and ice machine – position ice machine with connections facing rear of bin.
§§ If using existing bin – place supplied gasket 2.5" (64 mm) from front of bin (Fig. 1). Position ice machine with utility
connections facing rear of bin.
Fig. 1
bin top
Apply supplied gasket to bin top
as shown. Position ice machine
on bin top.
top view shown
add gasket
2.5"
(64 mm)
existing gasket
front of ice machine
6. Make final plumbing and electrical connections.
7. Working from inside bin storage area, push end of transport tube without fasteners up through grommets
into ice machine, leaving about 2" (51 mm) hanging down in bin.
8. Route free end of tube to evaporator port.
9. Slip a hose clamp in free end of tube.
10.Push free end of tube on evaporator port and tighten clamp, making sure clamp is positioned on evaporator
side of flange (no flange on MFD400 series flake ice machine).
11.Position ice tube under float bracket retaining tab.
12.Carefully slip ice level control stat alongside transport tube through both grommets and down into bin.
13.Run ice level control stat down through one side of cap tube fasteners attached to ice transport tube, form
a 180˚ bend at end of tube and run back up through fastener (Fig. 2).
Fig. 2
bin top
ice transport tube
ice level control
stat fastener
ice level control stat
14.Adjust loop length to provide desired ice level. Loop must below end of ice transport tube.
15.Carefully bend end of cap tube to prevent it from slipping out of clamp.
Before turning power on
1. Clean and sanitize ice storage bin in accordance with cleaning procedure in ice storage bin installation
information packed with ice storage bin.
8
T400A/W, MCD400A/W, R400A/W, MFD400A/W, D400A/W Ice Machines
2.
3.
4.
5.
6.
Turn water to ice machine on.
Remove cover on float reservoir.
Push down on float to force water out overflow tube and into evaporator drain pan.
Check that water drains freely from evaporator drain pan.
Lift float and check that float valve shuts off incoming water when raised.
After turning power on
1. Turn power to ice machine on and confirm that gearmotor, compressor and fan motor start immediately.
2. Check that ice begins to enter bin within approximately 10 minutes.
3. With ice machine running, check that float reservoir water level is approximately 3/8" (10mm) below internal
overflow and adjust to this level (raised line on side of reservoir) if necessary.
4. After making ice for 10 minutes, put ice against ice level control stat cap tube and check that ice machine
shuts down.
5. Warm ice level control stat with your fingers and check that ice machine restarts in approximately
20 minutes. (Bin must be calling for ice.)
RIDE model ice machine installation procedure (models MCD400A/WHS and MCD400A/WVS)
RIDE model ice machine performance is very sensitive to the quality of installation. To ensure proper performance,
ease of service and warranty coverage. it is critical that you follow the requirements detailed in this manual. If you
can not meet these requirements or have questions, call our technical service group immediately at (877) 612-5086
or +1 (610) 252-7301.
Installing RIDE model ice machine and rough-in utilities without optional slide-out accessory
The requirements below are for ice machine installation without the Follett slide-out accessory. These procedures
ensure that the ice machine can be easily removed as one unit for cleaning and maintenance. For installation
with the slide-out accessory, refer to instructions to install ice machine and rough-in utilities with optional slide-out
accessory.
General requirements
§§ Front of ice machine free of obstructions, plumbing lines, electric conduits.
§§ 12" (305 mm) minimum clearance above ice machine for access to ice machine components.
§§ 6" (15.3 cm) minimum clearance between exhaust side of ice machine and adjacent equipment.
§§ Do NOT weld ice machine to counter channels.
§§ Large, removable panels in counter face to allow ice machine removal.
§§ Machine stand accessory required for ice machines not supported on counter channels.
Connection requirements
§§ Compression fittings for water and drain lines.
§§ Separate drains for condenser and ice machine. Do NOT connect drains.
§§ 20A power supply with 6 feet.
bin signal from
dispenser
to ice machine
12"
305mm
clearance
separate power
to dispenser
front of
ice machine
clear
separate power
to ice machine
water shut off
compression fittings
for water and drain lines
Note:Diagram intended as guide only. All field wiring to be installed in accordance with NEC and local electrical
codes.
T400A/W, MCD400A/W, R400A/W, MFD400A/W, D400A/W Ice Machines9
Field wiring diagrams for RIDE model ice machine installations
§§ All field wiring must be installed in accordance with NEC and local electrical codes.
§§ Field wiring diagram is intended only to aid electrician or technician in understanding how equipment works.
§§ Should local codes require a hard-wired connection and/or shielded wiring, eliminate the cord and plug(s) and
follow the appropriate field wiring diagram.
§§ MCD400A/W and R400A/W ice machines have separate power supply from dispenser.
§§ Electric disconnects required within 10 ft (3 m) for all hard-wired connections.
Recommended junction box preparation of hard-wired RIDE
model ice machines.
1. Cut plugs from supplied power cords.
2. Replace upper (power) strain relief with
a cord connector.
3. Mount two 2" x 4" junction boxes using supplied holes in
ice machine face.
4. Make power and bin signal connections.
25, 50 or 110 ice and water dispenser with ONE RIDE model ice machine
(dispenser models 25CR400A/W, 25HR400A/W, 50CR400A/W, 50HR400A/W, 110CR400A/W)
Electric
power
source
Electric
power
source
Lower ice machine
junction box
(bin signal)
Dispenser
junction box
GND
X
LEGEND
Upper ice machine
junction box
(power)
GRN
X
GND GRN
X
B
W
R
W
W
B
B
B
W
GRN
BL
Y
RD
WIRENUT FIELD
CONNECTIONS
EQUIPMENT
GROUND
BLACK
WHITE
GREEN
BLUE
YELLOW
RED
VU155/VU300 ice and beverage dispenser with ONE or TWO RIDE model ice machines
Note: 24 V bin signal; Verify black bin signal wire is on the 24 V terminal
Ice machine #1
(optional)
Electric
power
source
Lower junction box
(24V bin signal)
DISPENSER
Electric
power
source
Left junction box
W
W
B
B
W
Right junction box
GRN
GND X
BL
B
Y
GND
GRN
Upper junction box
(power)
RD
Ice machine #2
(optional)
Lower junction box
(24V bin signal)
Electric
power
source
W
B
Upper junction box
(power)
W
B
GRN
GND X
10
T400A/W, MCD400A/W, R400A/W, MFD400A/W, D400A/W Ice Machines
Installing RIDE model ice machine and rough-in utilities with optional slide-out accessory
The slide-out accessory allows the ice machine to be pulled out on a track from below a counter without
disconnecting utilities. A leg supports the ice machine in the full-out position. If your order did not include a slide-out
accessory proceed to ice machine ventilation and exhaust.
Step 1 – Installing track accessory (Follow either A or B below for RIDE model ice machine)
Track must be positioned flush against inside of counter and slightly above counter access opening.
A. When ice machine stand is used (required if ice machine is not supported on counter channels)
1. Bolt vertical utility panel to slide-out track assembly with supplied 10/32 screws.
2. Secure slide-out track assembly to ice machine stand with 10/32 screws provided.
3. Position ice machine stand in desired location and adjust stand legs to proper height and level in both
directions.
4. Using holes in flanged legs as template, mark floor for 12 anchoring holes to be drilled.
5. Remove stand/track assembly and drill marked holes.
6. Reposition and anchor stand to floor with 12 fasteners appropriate to floor material (not supplied).
CAUTION!
Stand must be anchored to avoid tipping and possible injury when ice machine is pulled out.
B. When ice machine is supported on counter channels
1. Bolt vertical utility panel to slide-out track assembly with supplied 10/32 screws.
2. Position track assembly on counter channels (Fig. 3).
3. Using holes in track assembly as a template, mark and drill required holes in counter channels.
4. Remove track assembly on channels and drill marked holes.
5. Reposition track assembly on channels and secure using appropriate hardware (not supplied).
14"
(35.6 cm)
13"
(33.1 cm)
vertical utility panel
12.75"
(32.4 cm)
14"
(35.6 cm)
slide-out-track
T400A/W, MCD400A/W, R400A/W, MFD400A/W, D400A/W Ice Machines11
Step 2 – Installing RIDE model ice machine on slide-out track
position track accessory so that 2" (51mm) duct
supplied with air-cooled RIDE model ice machine mates
with back of counter opening.
counter front
grille supplied with aircooled RIDE model ice machines
power cord
bin signal cord
(icemaker connection)
bin signal cord
(customer connection)
air in
(air-cooled units only)
A. When ice machine is shipped with slide-out track accessory (follow either A or B)
1. Connect inlet water, drain, and power supply to back of vertical utility panel.
2. Place ice machine on slide-out track assembly.
3. Connect drain and water lines.
4. Connect electrical plugs from ice machine to utility panel.
B. When ice machine is installed in and shipped with counter
1. Remove two outer rear screws from ice machine and install supplied spacer and screw (Fig. 3).
2. Place ice machine on slide-out track assembly.
3. Connect drain and water lines.
4. Connect electrical plug from ice machine to utility panel.
5. Remove pin from adjustable leg.
6. Place hold-down strap over leg block and secure strap to slide-out assembly with supplied screws (Fig. 4).
7. Reinstall pin in leg block.
8. At job site remove hold-down strap and make utility connections at rear utility panel.
Fig. 3
Fig. 4
hold-down strap
(for installation; remove
and discard)
Remove screw. Install
supplied screws and spacers.
12
T400A/W, MCD400A/W, R400A/W, MFD400A/W, D400A/W Ice Machines
Supplied screws (for installation;
remove and discard)
Front view
3/8" OD push-in condenser inlet
(water-cooled only)
5.25"
(134 mm)
ice machine
power outlet
3/8" OD push-in condenser drain
(water-cooled only)
ice machine
twist-lock
bin signal cord
3/8" OD push-in icemaker water inlet
barbed push-on icemaker drain
25.875"
(658 mm)
Side view
(All customer field
connections are made
to rear of vertical
utility panel)
3/8" OD push-in condenser inlet
(water-cooled only)
cord holder
3/8" OD push-in condenser drain
(water-cooled only)
vertical utility panel
3/8" OD push-in ice machine water inlet
16.75"
(41.5 cm)
icemaker power cord
bin signal cord connector
(to connect to dispenser bin signal cord)
3/4" MPT ice machine drain
22.75"
(57.8 cm)
Plan view
22.75"
(57.8 cm)
Ice machine front
1.563"
(40 mm)
16"
(40.7 cm)
1.563"
(40 mm)
19.25"
(48.9 mm)
25.875"
(65.8 cm)
T400A/W, MCD400A/W, R400A/W, MFD400A/W, D400A/W Ice Machines13
RIDE model ice machine ventilation and exhaust requirements
Fabricator-supplied, custom air intake grilles must have 12" x 12" (30.5 cm x 30.5 cm) opening yielding
100 sq. inches (645 sq. cm) of open air space within duct perimeter. Block off any open area outside of the air duct.
Intake air requirements — air-cooled ice machines (MCD400AHS, MCD400AVS & R400A only)
1. Check that 2" (51 mm) duct is installed on condenser front.
2. Cut a 12" x 12" (30.5 cm x 30.5 cm) opening in counter face to align with duct.
3. Position ice machine to mate duct flush with back of counter opening.
4. Install supplied grille on outside of counter opening.
Exhaust air — all ice machines (MCD400A/W & R400A/W)
Provide 100 sq. in. (645 sq. cm) of counter opening for exhaust air at least 18" (45.7 cm) from intake opening but not
more than 10 ft (3 m) away.
MCD400AHS, MCD400AVS & R400A — Side View
Standard
louvered grille
(supplied)
Air intake
Exhaust air
Supplied 2" (51mm) duct MUST be installed
to front of ice machine and mated flush to inside
of counter face opening.
Front View
Standard 2” (51 mm)
duct mates counter
opening (behind
grille) to condenser
front
Air in
through louver
Exhaust air
out side to
opening at least
18” (45.7) cm
from air intake
Air out through louver
Provide at least 100 sq. in.
(645 sq. cm) of counter
opening for exhaust air
14
T400A/W, MCD400A/W, R400A/W, MFD400A/W, D400A/W Ice Machines
RIDE model ice machine ice transport tube installation
Incorrect ice transport tube installation can result in wet ice and dispensing problems. Follow guidelines below to
ensure correct installation. Call factory for assistance if you are unable to meet these requirements.
General requirements
§§ Maximum length of tube run – 20 ft (6 m). Factory approval required for longer runs.
§§ Run tube without dips.
§§ One continuous length of tube; no splices.
§§ Minimum radius of bends in tube – 6" (15.3 cm) inside radius.
§§ Maximum number of bends – 6.
§§ Insulation on entire run of ice tube.
Procedure
1. If installing MCD series ice machine refer to additional connection specifications for Vision series ice and
beverage dispensers instructions below.
2. Select side, rear or top knockout in ice machine cabinet for tube entrance.
3. Install supplied grommet in knockout.
4. Remove ice machine top panel.
5. Install supplied insulation on entire length of tube.
6. Run insulated tube without dips between ice machine and dispenser and secure in place.
7. Cut insulation off tube where tube enters grommet.
8. Slide end of tube without insulation through grommet and run to evaporator port.
9. Cut tube to that length.
10.Install a section of insulation on tube from grommet to evaporator port.
11.Slip supplied hose clamp over free end of tube.
12.Pull insulation back from free end of tube.
13.Push tube on evaporator port.
14.Position clamp behind lip on evaporator port and tighten clamp.
Correct installation
Incorrect installation
§§ Length of run no more than 20 ft (6 m)
§§ Tube run continuously from ice machine to
dispenser
§§ Insulation on entire run of tube
§§ No dips or tight bends
§§ Tube secured in place
§§ No splices
§§ Dips in tube where water can collect
§§ Splice or tight bend that restricts ice flow
§§ Uninsulated tube that results in wet ice and
potential dispensing problems
T400A/W, MCD400A/W, R400A/W, MFD400A/W, D400A/W Ice Machines15
Additional ice transport tube connection specifications for Vision series ice and beverage dispensers
Check to make sure bin signal on ice machine control board is switched to 24 V connection.
1. Push one end of ice transport tube(s) through hole(s) provided in side of dispenser.
2. Route tube into ice tube bracket inside dispenser and engage bracket tabs in holes located in end of ice
transport tube(s) (see drawings below).
3. Verify bin thermostat capillary tube is mounted correctly (see drawings below).
Ice tube retainer bracket
1" (26 mm)
ice tube
retaining
bracket
ice tube
ice tube
Bin thermostat capillary tube mounting
Front View, VU155
Front View, VU300
ice tube
retaining
bracket
thermostat
ice tube
16
thermostat
tabs in ice tube
retainer bracket
engage holes in ice
tube and hold tube
in place
ice tube
retaining
bracket
ice tube
T400A/W, MCD400A/W, R400A/W, MFD400A/W, D400A/W Ice Machines
thermostat
Ice transport tube installation detail
install insulation on full run of tube
1
2
Dispenser
Heat end of transport tube in cup of 160 F
(71 C) hot water to soften (1) and spread with
pliers before making connection (2).
grommet
Evaporator
install clamp behind lip
on evaporator port
RIDE model ice machine start up procedure
The start-up procedure below is intended to ensure that ice machine is operating properly after installation has been
made. Check each item listed and call factory immediately for assistance if you experience problems with unit.
Before turning on power
1. Turn on water to ice machine.
2. Push down on float to force water through overflow chamber into evaporator drain pan and check for proper
drainage of drain pan.
3. Check that float valve shuts off incoming water when raised.
4. Check that hose clamp securely holds ice transport tube on evaporator port.
After turning on power
1. Turn on power to ice machine and confirm that gearmotor, fan motor and compressor start immediately.
2. Check that ice begins to enter dispenser bin area within approximately 10 minutes.
3. Check that float reservoir water level is approximately 3/8" (.95mm) below overflow during ice machine
operation and adjust to this level if necessary.
4. Put ice against bin level thermostat in dispenser bin and check that compressor and fan motor shut down
approximately 10 seconds after thermostat opens. Gearmotor should run for an additional 60 seconds.
5. Check that ice machine comes back on in approximately 20 minutes (bin signal must be present).
Cleaning/descaling and sanitizing
Periodic cleaning/descaling and sanitizing of Follett’s ice machine system is required to ensure peak performance
and delivery of clean, sanitary ice. The recommended cleaning procedures that follow should be performed at least
as frequently as recommended and more often if environmental conditions dictate.
Cleaning of the condenser can usually be performed by facility personnel. Cleaning/descaling and sanitizing of
the ice machine system should be performed by your facility’s trained maintenance staff or a Follett authorized
service agent. Regardless of who performs the cleaning, it is the operator’s responsibility to see that this cleaning is
performed according to the schedule below. Service problems resulting from lack of preventive maintenance will not
be covered under the Follett warranty.
Symphony
Frequency
Drain Line
weekly
Drain Pan/Drip Pan
weekly
Exterior
as needed
Condenser
monthly (air-cooled only)
Ice Machine
semi-annually
Transport Tube
semi-annually
* Ice machine must be cleaned and sanitized prior to start-up.
T400A/W, MCD400A/W, R400A/W, MFD400A/W, D400A/W Ice Machines17
Weekly
The exterior may be cleaned with a stainless cleaner such as 3M* Stainless Steel Cleaner & Polish or equivalent.
* 3M is a trademark of 3M Company.
Monthly
Condenser (air-cooled ice machine only)
1. Use a vacuum cleaner or stiff brush to carefully clean condenser coils of lint and debris to ensure optimal
performance.
2. When reinstalling counter panels in front of RIDE model ice machines, be sure that ventilation louvers line
up with condenser air duct.
Semi-Annually (more often if conditions dictate)
§§ A cleaning/descaling and sanitizing procedure should always include both the ice machine and dispenser; ice
machine should be cleaned and sanitized first, followed by the dispenser.
§§ Icemaking system can be cleaned/descaled in place.
To ensure that your ice machine and dispenser are cleaned/descaled and sanitized properly, proceed as follows:
1. Clean/descale the ice machine
2. Sanitize the ice machine
3. Clean/descale the dispenser
4. Sanitize the dispenser
CAUTION!
§§ Wear rubber gloves and safety goggles (or face shield) when handling cleaner or sanitizer mixtures.
§§ Use only Follett approved cleaners.
§§ It is a violation of Federal law to use Solution A or Solution B in a manner inconsistent with their labeling.
§§ Do not use solvents, abrasive cleaners, metal scrapers or sharp objects to clean any part of the dispenser.
Solution A: Following manufacturer’s instructions, mix cleaning solution of 1 gal. (3.8 L) 120 F (49 C) water and 7 oz.
(198 g) (one 7 oz. packet) of Follett SafeCLEAN™ ice machine cleaner/descaler (P/N 00132001).
Solution B: Following manufacturer’s instructions, mix a sanitizing solution of 1 gal. (3.8 L) 120 F (49 C) water and
1.6 oz. (48 ml) Nu-Calgon IMS-II Sanitizer (P/N 00979674).
Clean/descale ice machine
1. If ice machine was running recently, ensure that the evaporator is completely free of ice before proceeding.
2. Disconnect power to ice machine.
3. Remove any ice machine panels required to gain access to water reservoir and electrical control box.
4. Turn compressor switch on electrical box of ice machine to OFF position.
5. Remove water reservoir cover and close water supply valve (or block up reservoir float).
6. Drain water from reservoir by releasing evaporator drain tube from float reservoir bracket, removing plug from
drain tube and releasing (unclamping) pinch clamp (if equipped).
7. Plug drain hose, replace drain line in reservoir bracket and pour part of Solution A into reservoir, filling it almost
to overflowing.
8. Remove stainless steel ice compression nozzle and drain lines and submerge in a cup of Solution A while
cleaning/descaling rest of system. (Flake ice machines have no ice compression nozzle and drain lines.)
CAUTION: To avoid potential pitting, do not soak parts in Solution A for more than 45 minutes.
9. Restore power to ice machine (gearmotor will run; compressor and fan will not).
10.Inspect evaporator drain pan and drain line and remove any accumulated scale build up.
11. After 15 minutes, turn power OFF; drain solution from reservoir and evaporator.
12.Fill reservoir almost to overflowing with clean water to rinse. Drain. Repeat two more times.
13.Rinse ice compression nozzle and drain lines in clean water.
Sanitize ice machine
14.Submerge ice compression nozzle and drain lines in a cup of Solution B while following steps 15-21.
15.Connect ice transport tube directly onto evaporator outlet port without ice compression nozzle.
16.Fill reservoir almost to overflowing with Solution B.
17.Restore power to ice machine (gearmotor will run; compressor and fan will not).
18.After 10 minutes, turn compressor switch to ON position.
19.As unit starts to make ice, continue to pour Solution B into reservoir, maintaining level just below reservoir
overflow.
18
T400A/W, MCD400A/W, R400A/W, MFD400A/W, D400A/W Ice Machines
20.Continue to make ice with Solution B for 20 minutes.
21.Turn power to ice machine OFF.
22.Disconnect ice transport tube from evaporator outlet port. Rinse ice compression nozzle and drain lines in clean
water and reinstall on evaporator outlet. Reconnect ice transport tube to ice compression nozzle.
23.Drain any remaining Solution B from evaporator.
24.Fill reservoir almost to overflowing with 120 F (49 C) clean water to rinse. Drain. Repeat two more times. Reclamp pinch clamp, replace drain plug, and re-secure drain tube ensuring that end of drain tube is above water
level in reservoir.
25.Open water supply valve (or unblock float) and replace reservoir cover; restore power to ice machine and ensure
compressor switch is in ON position. Make ice for at least 15 minutes to flush any remaining Solution B from
system (RIDE ice machines with long ice transport hoses may take longer to flush out). Discard this ice and all
ice made during sanitizing.
26.Reinstall all parts and replace any panels removed prior to cleaning.
Service
Ice machine Operation (all models)
Follett’s ice machine consists of four distinct functional systems:
§§ Refrigeration system
§§ Water system
§§ Harvesting system
§§ Electrical control system
These four systems work together to accomplish the production and harvesting of ice. A problem in any one of these
systems will result in improper operation of the entire ice production cycle. When troubleshooting the ice machine,
it is important to analyze the entire system operation to determine which system is not functioning properly, then
pinpoint the component within that system that is malfunctioning. Determine what corrective action must be taken
before making any adjustments or replacing any components.
The icemaking process
Harvest system diagram
The Follett ice machine uses a stainless steel jacketed
evaporator and operates on a continuous freezing
cycle. Water is supplied to the evaporator from the
water reservoir where the water level is controlled by
a float valve. This valve also shuts off the water supply
when the ice machine is not running.
When the ice machine is running, a layer of ice forms
on the interior surface of the evaporator. This ice is
continuously removed by a slowly rotating (12 RPM)
auger. The auger carries the ice upward into the
cavity formed by the top bearing housing and the
compression loop, where it is compressed to remove
excess water. When the ice reaches the desired
hardness it rotates within the cavity and is forced
through a discharge port and compression nozzle and
into the ice transport tube. The discharge tube and
compression nozzle are slightly restricted to further
compress the ice and produce the desired hardness.
evaporator
port
ice transport tube
compression nozzle
auger
water
inlet
Note: MFD series flake ice machines have no
compression nozzle. As the formation of ice continues,
ice in the transport tube is pushed through the tube to
the storage compartment in the ice dispenser or ice
storage bin.
A solid state control board located in the electrical
box of the ice machine controls the normal operation
of the ice machine and monitors gearmotor torque.
This control board will shut down the ice machine should an over-torque condition occur. It is very important that
you familiarize yourself with the operational sequences detailed in this manual before attempting to service the ice
machine.
T400A/W, MCD400A/W, R400A/W, MFD400A/W, D400A/W Ice Machines19
Technical specifications (all models)
Refrigeration system diagram
high pressure
switch
high side
service port
condenser
low side
service port
filter dryer
compressor
evaporator
high
pressure
vapor
thermostatic
expansion
valve
low
pressure
liquid
high
pressure
liquid
low
pressure
vapor
Refrigeration pressure data
Air-cooled Ice Machine Refrigeration Pressure
Discharge Pressure/Suction Pressure
Ambient air temperature ˚F/˚C
˚F/˚C
60/16
Water-cooled Ice Machine Refrigeration Pressure
Discharge Pressure/Suction Pressure
Condenser inlet water temperature ˚F/˚C
Ice machine inlet water
temperature ˚F/˚C
Ice machine inlet water
temperature ˚F/˚C
§§ Water regulating valve is factory set at 225 PSIG head pressure.
§§ Readings within 10% of table values should be considered normal.
80/27 100/38
50/10 174/23 245/31 237/37
psi
70/21 174/23 244/30 326/38
psi
90/32 190/25 265/32 347/40
psi
˚F/˚C
50/10
70/21
90/32
50/10 236/28 235/29 250/34
psi
70/21 237/28 230/30 250/34
psi
90/32 236/28 235/30 250/34
psi
Compressor data
Compressor current draw
Air-cooled
Ambient air temperature
60 F/15.6 C
70 F/21.1 C
80 F/26.7 C
90 F/32.2 C
100 F/37.8 C
6.3A
6.5A
6.7A
6.9A
7.1A
50 F/10 C
60 F/15.6 C
70 F/21.1 C
80 F/26.7 C
90 F/32.2 C
6.6A
6.7A
6.7A
6.8A
6.9A
Water-cooled
Water temperature at float
Locked rotor amps58.8A
20
T400A/W, MCD400A/W, R400A/W, MFD400A/W, D400A/W Ice Machines
Water-cooled ice machine capacity/24 hrs.
Ambient Air Temperature ˚F/˚C
Ambient Air Temperature ˚F/˚C
F
C
50
10
60
16
70
21
80
27
90
32
60
16
510
232
482
219
454
206
424
193
394
179
70
21
454
206
435
198
417
190
385
175
354
161
80
27
397
180
389
177
380
173
347
158
313
142
90
32
335
152
329
150
323
147
297
135
270
123
100
38
273
124
270
123
266
121
247
112
227
103
Performance with new RG Group 1/2 ton coil
(Note: Data expressed in lbs/hr and kg/hr)
lbs.
kg.
lbs.
kg.
lbs.
kg.
lbs.
kg.
lbs.
kg.
F
C
50
10
60
16
70
21
80
27
90
32
Inlet Water Temperature ˚F/˚C
Inlet Water Temperature ˚F/˚C
Air-cooled ice machine capacity/24 hrs.
60
16
451
204
423
192
394
179
371
168
352
160
70
21
447
202
413
187
390
177
361
163
342
155
80
27
442
200
409
185
380
172
352
160
333
151
90
32
437
199
399
181
371
168
342
155
323
146
100
38
428
194
394
179
361
163
333
151
309
140
lbs.
kg.
lbs.
kg.
lbs.
kg.
lbs.
kg.
lbs.
kg.
Note: Nominal values – actual production may vary by ± 10%
Gearmotor data
Gearmotor current
Locked rotor amps
2.25A (nominal)
14A
Electrical control system operation
MCD400A/WBT, MCD400A/WHT and MFD400A/WBT wiring diagram
Follett ice machines used on top of an ice storage bin have a slightly different circuitry. A diagram for these ice
machines is shown below. The operational and diagnostic stages for these ice machines will be otherwise the same
as the following Stages 1 - 10.
INPUT
POWER
W
B
WATER
SENSOR
G
GRD
PWR
GRD
DR
L1
BLACK
M
WHITE
C
CONTROL
BOARD
L2
L2
L2
L2
R
ORANGE
C
S
RED
M
1
S
L BLACK
BLACK
T.O.L.
COMPRESSOR
FAN
DRIVE
BLACK
BLACK
BLACK
HIGH PRESSURE
SAFETY SWITCH
BLACK
BIN SIGNAL
FROM DISPENSER
JUNCTION BOX
WTR
B-T
B-E
RED
RED
COMPRESSOR
SWITCH
WHITE
START
RELAY
4
BLUE
WHITE
GEAR MOTOR
2
BLACK
START
3
YELLOW
RUN
START CAP.
RED
BLACK
BISON GEARMOTOR
T.O.L.
GEAR MOTOR
OR
LINIX GEARMOTOR
START
RUN
24V
COMMON
LINE VAC
BLACK
60M
2ND
RED
COMPRESSOR
20M
RED
FAN
L1
L2
WHITE
WHITE
BIN T-STAT
RESET
T.O.L.
T400A/W, MCD400A/W, R400A/W, MFD400A/W, D400A/W Ice Machines21
Electrical control system operation
The D400A/W, MCD400A/WVS and R400A/W wiring diagrams which follow illustrate the circuitry of Follett ice
machines used with ice dispensers. Both normal operation of the ice machine (Stages 1 - 6) and non-normal
diagnostic sequences showing torque-out (Stages 7 - 10) for use in troubleshooting ice machine problems are
shown.
Follett ice machines used on top of an ice storage bin have a slightly different circuitry. The operational and
diagnostic stages for these ice machines will be otherwise the same as Stages 1 - 10 that follow.
Circuitry notes
When the ice machine is used with a dispenser it receives power from two sources – the main power supply and
the bin control signal power from the dispenser. Disconnect both power sources before performing service. When
performing electrical service, always use a meter to determine whether or not the components being serviced are
energized.
§§ High pressure cutout opens at 425 PSI and closes at 287 PSI (auto reset).
§§ Compressor switch should read open in on position.
§§ Compressor start relay is position sensitive. See label on start relay for proper orientation.
§§ Bin signal may be 120 V, 60 Hz; 230 V, 50 Hz; or 24 V, 60 Hz. If bin signal is 24 V, 60 Hz, black bin signal wire must
be moved from LINE VAC terminal to 24 V terminal.
§§ Flashing water LED at any time indicates that water signal to board had been lost for more than
one second.
§§ Ten-second delay: There is a 10 second delay in reaction to loss of water (WTR) or bin (B-E) signals. If signals are
not lost for more than 10 seconds, no reaction will occur.
Normal operation – Stage 1
Power is supplied to L1 of the control board. The ice level control in the dispenser is closed and calling for ice,
supplying signal voltage to the control board. The control board will now go through the start-up sequence. Less than
30 seconds will elapse as the water sensor located in the float reservoir checks for water in the reservoir. The Bin
Empty LED (B-E) will be on.
INPUT
POWER
WATER
SENSOR
GRD
G
GRD
B
WHITE
W
BLACK
BLACK
M
WHITE
R
ORANGE
S
L2
L2
COMPRESSOR
FAN
DRIVE
BLACK
M
1
S
L
3
YELLOW
RUN
BISON GEARMOTOR
T.O.L.
WHITE
START CAP.
RED
BLUE
BLACK
START
OR
GEAR MOTOR
LINIX GEARMOTOR
START
RUN
WTR
B-T
B-E
RED
RED
COMPRESSOR
SWITCH
WHITE
GEAR MOTOR
2
WHITE
BLACK
HIGH PRESSURE
SAFETY SWITCH
START
RELAY
60M
BLACK
BLACK
BLACK
20M
2ND
BLACK
WHITE
RED
4
CONTROL
BOARD
24V
COMMON
LINE VAC
BLACK
T.O.L.
C
RED
COMPRESSOR
C
DR
L1
L1
L2
L2
L2
FAN
22
PWR
RESET
T.O.L.
T400A/W, MCD400A/W, R400A/W, MFD400A/W, D400A/W Ice Machines
RED
BIN SIGNAL
FROM DISPENSER
BIN T-STAT
JUNCTION BOX
(MCD400A/WVS series –
blk wire is on 24V)
Normal operation – Stage 2
The water sensor verifies water in the float. The Water OK LED (WTR) comes on. At the same time, the gearmotor,
compressor, and condenser fan motor come on, lighting the Drive LED (DR) and compressor LED (C). The
compressor is started through a current style relay that is pulled in by the initial high current draw of the compressor.
The gearmotor start windings are also energized through a current relay (or start capacitor). The B-E and WTR LED
remain on.
INPUT
POWER
WATER
SENSOR
GRD
G
PWR
RESET
GRD
B
WHITE
W
BLACK
M
WHITE
R
ORANGE
M
1
S
L
S
T.O.L.
BLACK
WHITE
HIGH PRESSURE
SAFETY SWITCH
BLACK
3
YELLOW
RUN
BISON GEARMOTOR
T.O.L.
GEAR MOTOR
LINIX GEARMOTOR
START
RED
Normal operation – Stage 3
B-E
RED
RED
COMPRESSOR
SWITCH
RED
BIN SIGNAL
FROM DISPENSER
BIN T-STAT
JUNCTION BOX
(MCD400A/WVS series –
blk wire is on 24V)
OR
WHITE
START CAP.
BLUE
2
B-T
WHITE
GEAR MOTOR
START
WHITE
BLACK
BLACK
START
RELAY
WTR
BLACK
BLACK
RED
4
2ND
COMPRESSOR
FAN
DRIVE
BLACK
60M
L2
L2
24V
COMMON
LINE VAC
BLACK
20M
CONTROL
BOARD
RED
COMPRESSOR
C
C
L2
L2
FAN
BLACK
DR
L1
L1
L2
RUN
T.O.L.
After the initial high current draw drops off, the gearmotor start relay contacts open dropping out the start winding (or
start capacitor). As the compressor comes up to normal running speed, the compressor start relay contacts open,
dropping out the start winding of the compressor. The ice machine is now in a normal icemaking mode. The ice
machine will produce ice until the bin level control in the ice dispenser is satisfied. The B-E, DR, C and WTR LEDs
are all on.
INPUT
POWER
WATER
SENSOR
GRD
G
GRD
B
WHITE
W
BLACK
BLACK
M
WHITE
R
ORANGE
S
L2
L2
COMPRESSOR
FAN
DRIVE
BLACK
M
1
S
L
3
BLACK
START
YELLOW
RUN
BISON GEARMOTOR
T.O.L.
WHITE
START CAP.
RED
OR
GEAR MOTOR
LINIX GEARMOTOR
START
RUN
WTR
B-T
B-E
RED
RED
COMPRESSOR
SWITCH
WHITE
GEAR MOTOR
BLUE
2
WHITE
BLACK
WHITE
HIGH PRESSURE
SAFETY SWITCH
START
RELAY
60M
BLACK
BLACK
BLACK
20M
2ND
BLACK
RED
4
CONTROL
BOARD
24V
COMMON
LINE VAC
BLACK
T.O.L.
C
RED
COMPRESSOR
C
DR
L1
L1
L2
L2
L2
FAN
PWR
RESET
RED
BIN SIGNAL
FROM DISPENSER
BIN T-STAT
JUNCTION BOX
(MCD400A/WVS series –
blk wire is on 24V)
T.O.L.
T400A/W, MCD400A/W, R400A/W, MFD400A/W, D400A/W Ice Machines23
Normal operation – Stage 4
Once the ice level control opens, the B-E LED goes out. After a 10 second delay the LED (C), compressor, and
fan motor go off and the B-T LED comes on. (Should the ice level control not remain open for 10 seconds, the ice
machine will continue to run.) The gearmotor continues to run for 60 seconds. The purpose of this function is to drive
the remaining ice out of the evaporator and to boil off any refrigerant remaining in the evaporator.
INPUT
POWER
WATER
SENSOR
GRD
G
PWR
RESET
GRD
B
WHITE
W
BLACK
M
WHITE
L2
L2
R
ORANGE
S
M
1
S
L
WHITE
HIGH PRESSURE
SAFETY SWITCH
START
RELAY
2
BLACK
3
YELLOW
RUN
BISON GEARMOTOR
T.O.L.
GEAR MOTOR
LINIX GEARMOTOR
START
RED
Normal operation – Stage 5
B-T
B-E
RED
RED
COMPRESSOR
SWITCH
RED
BIN SIGNAL
FROM DISPENSER
BIN T-STAT
JUNCTION BOX
(MCD400A/WVS series –
blk wire is on 24V)
OR
WHITE
START CAP.
BLUE
4
WTR
WHITE
GEAR MOTOR
START
WHITE
BLACK
BLACK
BLACK
60M
BLACK
BLACK
RED
COMPRESSOR
FAN
DRIVE
BLACK
20M
2ND
24V
COMMON
LINE VAC
BLACK
T.O.L.
CONTROL
BOARD
RED
COMPRESSOR
C
C
L2
L2
FAN
BLACK
DR
L1
L1
L2
RUN
T.O.L.
The B-T LED will remain on for 20 minutes. The ice machine will not start while the B-T LED is on. To restart the ice
machine for troubleshooting purposes, depress the reset button to clear the control board.
INPUT
POWER
WATER
SENSOR
GRD
G
GRD
B
WHITE
W
BLACK
BLACK
M
WHITE
R
ORANGE
S
COMPRESSOR
FAN
DRIVE
BLACK
M
1
S
L
START
3
YELLOW
RUN
BISON GEARMOTOR
T.O.L.
WHITE
START CAP.
RED
BLUE
BLACK
OR
GEAR MOTOR
LINIX GEARMOTOR
START
RUN
WTR
B-T
B-E
RED
RED
COMPRESSOR
SWITCH
WHITE
GEAR MOTOR
2
WHITE
BLACK
HIGH PRESSURE
SAFETY SWITCH
START
RELAY
60M
BLACK
BLACK
BLACK
20M
2ND
BLACK
WHITE
RED
4
L2
L2
24V
COMMON
LINE VAC
BLACK
T.O.L.
C
CONTROL
BOARD
RED
COMPRESSOR
C
DR
L1
L1
L2
L2
L2
FAN
24
PWR
RESET
T.O.L.
T400A/W, MCD400A/W, R400A/W, MFD400A/W, D400A/W Ice Machines
RED
BIN SIGNAL
FROM DISPENSER
BIN T-STAT
JUNCTION BOX
(MCD400A/WVS series –
blk wire is on 24V)
Normal operation – Stage 6
When the dwell time of 20 minutes has expired, the B-T LED goes off. The ice machine will go through the normal
start-up sequence when the bin level control signals the control board for ice. The WTR LED will remain on as long as
the water sensor in the float reservoir senses water.
INPUT
POWER
WATER
SENSOR
GRD
G
PWR
RESET
GRD
B
WHITE
W
BLACK
M
WHITE
L2
L2
R
ORANGE
S
M
1
S
L
HIGH PRESSURE
SAFETY SWITCH
START
RELAY
BLACK
START
3
YELLOW
RUN
BISON GEARMOTOR
T.O.L.
OR
WHITE
START CAP.
GEAR MOTOR
LINIX GEARMOTOR
START
RED
RUN
Diagnostic sequence – Stage 7
WTR
B-T
B-E
RED
RED
COMPRESSOR
SWITCH
WHITE
GEAR MOTOR
2
BLUE
4
WHITE
BLACK
BLACK
BLACK
60M
BLACK
BLACK
WHITE
RED
COMPRESSOR
FAN
DRIVE
BLACK
20M
2ND
24V
COMMON
LINE VAC
BLACK
T.O.L.
CONTROL
BOARD
RED
COMPRESSOR
C
C
L2
L2
FAN
BLACK
DR
L1
L1
L2
RED
BIN SIGNAL
FROM DISPENSER
BIN T-STAT
JUNCTION BOX
(MCD400A/WVS series –
blk wire is on 24V)
T.O.L.
The 20 minute error LED (20M) is on indicating that the control board has sensed an over-torque condition (above 3A
on the gearmotor) and shut the ice machine down. The 20M LED will remain on for 20 minutes after an over-torque
condition has occurred. The ice machine will remain off as long as the 20M LED is on. When the 20M LED goes off,
the control board will try to go through a normal start-up sequence. The WTR LED remains on as long as the water
sensor in the float reservoir senses water.
INPUT
POWER
WATER
SENSOR
GRD
G
GRD
B
WHITE
W
BLACK
BLACK
M
WHITE
R
ORANGE
S
COMPRESSOR
FAN
DRIVE
BLACK
M
1
S
L
START
3
YELLOW
RUN
BISON GEARMOTOR
T.O.L.
WHITE
START CAP.
RED
OR
GEAR MOTOR
LINIX GEARMOTOR
START
RUN
BLUE
BLACK
WTR
B-T
B-E
RED
RED
COMPRESSOR
SWITCH
WHITE
GEAR MOTOR
2
WHITE
BLACK
HIGH PRESSURE
SAFETY SWITCH
START
RELAY
60M
BLACK
BLACK
BLACK
20M
2ND
BLACK
WHITE
RED
4
L2
L2
24V
COMMON
LINE VAC
BLACK
T.O.L.
C
CONTROL
BOARD
RED
COMPRESSOR
C
DR
L1
L1
L2
L2
L2
FAN
PWR
RESET
RED
BIN SIGNAL
FROM DISPENSER
BIN T-STAT
JUNCTION BOX
(MCD400A/WVS series –
blk wire is on 24V)
T.O.L.
T400A/W, MCD400A/W, R400A/W, MFD400A/W, D400A/W Ice Machines25
Diagnostic sequence – Stage 8
If the restart is successful the 20M LED goes off, the 60 minute timer LED (60M) comes on. The 60M LED will remain
on for 60 minutes from restart. A lighted 60M LED tells the technician that the ice machine has experienced an overtorque condition. If the ice machine runs without problems for 60 minutes and no additional torque errors occur, the
60M LED will go off and the ice machine will continue normal operation.
INPUT
POWER
WATER
SENSOR
GRD
G
PWR
RESET
GRD
B
WHITE
W
BLACK
M
WHITE
R
ORANGE
S
M
1
S
L
WHITE
HIGH PRESSURE
SAFETY SWITCH
START
RELAY
BLACK
START
3
YELLOW
RUN
BISON GEARMOTOR
T.O.L.
GEAR MOTOR
LINIX GEARMOTOR
START
RED
Diagnostic sequence – Stage 9
B-T
B-E
RED
RED
COMPRESSOR
SWITCH
RED
BIN SIGNAL
FROM DISPENSER
BIN T-STAT
JUNCTION BOX
(MCD400A/WVS series –
blk wire is on 24V)
OR
WHITE
START CAP.
WTR
WHITE
GEAR MOTOR
2
BLUE
4
WHITE
BLACK
BLACK
BLACK
60M
BLACK
BLACK
RED
COMPRESSOR
FAN
DRIVE
BLACK
20M
2ND
24V
COMMON
LINE VAC
BLACK
T.O.L.
L2
L2
RED
COMPRESSOR
C
C
CONTROL
BOARD
L2
L2
FAN
BLACK
DR
L1
L1
L2
RUN
T.O.L.
The second error (2ND) LED will come on if an over-torque condition occurs while the 60M LED is still lighted. The
2ND LED will indicate to the technician that two consecutive over-torque situations have occurred. The ice machine
will shut down at this time and lock out. It will not restart unless the manual reset button is depressed.
INPUT
POWER
WATER
SENSOR
GRD
G
GRD
B
WHITE
W
BLACK
BLACK
M
WHITE
R
ORANGE
S
L2
L2
COMPRESSOR
FAN
DRIVE
BLACK
M
1
S
L
3
YELLOW
RUN
BISON GEARMOTOR
T.O.L.
WHITE
START CAP.
RED
OR
GEAR MOTOR
LINIX GEARMOTOR
START
RUN
BLUE
BLACK
START
WTR
B-T
B-E
RED
RED
COMPRESSOR
SWITCH
WHITE
GEAR MOTOR
2
WHITE
BLACK
HIGH PRESSURE
SAFETY SWITCH
START
RELAY
60M
BLACK
BLACK
BLACK
20M
2ND
BLACK
WHITE
RED
4
CONTROL
BOARD
24V
COMMON
LINE VAC
BLACK
T.O.L.
C
RED
COMPRESSOR
C
DR
L1
L1
L2
L2
L2
FAN
26
PWR
RESET
RED
BIN SIGNAL
FROM DISPENSER
BIN T-STAT
JUNCTION BOX
(MCD400A/WVS series –
blk wire is on 24V)
T.O.L.
T400A/W, MCD400A/W, R400A/W, MFD400A/W, D400A/W Ice Machines
Diagnostic sequence – Stage 10
If the water level in the float reservoir drops to an unacceptable level, the WTR LED will go out, shutting the ice
machine off. Also, the BT LED will come on, preventing the ice machine from restarting for twenty minutes. If water is
restored, the WTR LED will come back on and flash to alert the technician that water to ice machine has been lost.
The ice machine will then restart at the end of the 20 minute time delay. The flashing WTR LED can be cleared by
pressing the reset button.
INPUT
POWER
WATER
SENSOR
GRD
G
GRD
B
WHITE
W
BLACK
BLACK
M
WHITE
R
ORANGE
S
COMPRESSOR
FAN
DRIVE
BLACK
M
1
S
L
START
3
YELLOW
RUN
BISON GEARMOTOR
T.O.L.
WHITE
START CAP.
RED
OR
GEAR MOTOR
LINIX GEARMOTOR
START
RUN
BLUE
BLACK
WTR
B-T
B-E
RED
RED
COMPRESSOR
SWITCH
WHITE
GEAR MOTOR
2
WHITE
BLACK
HIGH PRESSURE
SAFETY SWITCH
START
RELAY
60M
BLACK
BLACK
BLACK
20M
2ND
BLACK
WHITE
RED
4
L2
L2
24V
COMMON
LINE VAC
BLACK
T.O.L.
C
CONTROL
BOARD
RED
COMPRESSOR
C
DR
L1
L1
L2
L2
L2
FAN
PWR
RESET
RED
BIN SIGNAL
FROM DISPENSER
BIN T-STAT
JUNCTION BOX
(MCD400A/WVS series –
blk wire is on 24V)
T.O.L.
T400A/W, MCD400A/W, R400A/W, MFD400A/W, D400A/W Ice Machines27
Refrigeration system (all models)
All service on refrigeration systems must be performed in accordance with all federal, state and local laws. It is the
responsibility of the technician to ensure that these requirements are met. Recharging ice machine to other than
factory specifications will void the warranty.
R404A ice machine charge specifications
Model
Charge
T400A, MCD400A, MFD400A, R400A, D400A (air-cooled)
19 oz. (539 g)R404A
T400W, MCD400W, MFD400W, R400W , D400W (water-cooled)
Refrigerant type
9 oz. (255 g)R404A
Refrigerant replacement requirements
1. Non-contaminated refrigerant removed from any Follett refrigeration system can be recycled and returned to
the same system after completing repairs. Recycled refrigerant must be stored in a clean, approved storage
container. If additional refrigerant is required, virgin or reclaimed refrigerant that meets ARI standard 700-88 must
be used.
2. In the event of system contamination (for example, a compressor burn out, refrigerant leak, presence of noncondensibles or moisture), the system must be repaired, evacuated and recharged using virgin or reclaimed
refrigerant that meets ARI standard 700-88.
3. Follett Corporation does not approve of recovered refrigerants. Improper refrigeration servicing procedures will
void the factory warranty.
Evacuation
Evacuate the system to a level of 500 microns. When the 500 micron level is reached, close valves and both manifold
and shut down the vacuum pump. Allow the system to sit for approximately 20 minutes. During this period the system
pressure should not rise. If the system pressure rises and stabilizes there is moisture in the system and further
evacuation is needed. If the pressure continues to rise check the system for leaks.
Ambients
Air temperature1 Water temperature2 MinimumMaximum
50 F/10 C 100 F/37.8 C
40 F/4.4 C 90 F/32.2 C
1Ambient air temperature is measured at the air-cooled condenser coil inlet.
2Ambient water temperature is measured in the ice machine float reservoir.
Ice capacity test
Ice machine production capacity can only be determined by weighing ice produced in a specific time period.
1.
2.
3.
4.
5.
6.
7.
8.
Replace all panels on ice machine.
Run ice machine for at least 15 minutes.
Weigh and record weight of container used to catch ice.
Catch ice for 15 or 20 minutes.
Weigh harvested ice and record total weight.
Subtract weight of container from total weight.
Convert fractions of pounds to decimal equivalents (ex. 6 lb 8 oz. = 6.5 lb).
Calculate production using following formula:
1440 min. x wt. of ice produced
Total test time in minutes
=
Production capacity/24 hr. period
9. Calculated amount per 24 hours should be checked against rated capacity for same ambient and water
temperatures in Ice Production Tables.
28
T400A/W, MCD400A/W, R400A/W, MFD400A/W, D400A/W Ice Machines
Service procedures
Fig. 7
Evaporator disassembly (Fig. 7)
1.
2.
3.
4.
Disconnect power to ice machine.
Shut off water to ice machine.
Drain evaporator and float tank.
Disconnect plastic tubing from evaporator water inlet, drain pan
stub, compression nozzle tubing and reservoir overflow tubing from
secured clip.
5. Disconnect ice transport tube from compression nozzle.
Note: No compression nozzle on MFD400 series flake ice machines.
6. Loosen nut and remove upper vee band coupling from top of
evaporator.
7. Lift top bearing assembly straight up with a slight rotating motion and
remove.
8. Remove ice compression loop located at top of auger.
9. Lift auger straight up and out of evaporator.
10. Remove nut and lower vee band coupling from bottom of evaporator.
11. Lift evaporator to clear bottom bearing assembly.
12. Loosen hex head bolt in side of mounting base with 5/16 wrench and
lift lower bearing assembly.
13. Remove condensate shield.
14. Remove 4 Allen head machine screws holding mounting base to
gearbox.
15. If replacing evaporator, remove compression nozzle from evaporator
port.
Evaporator reassembly (Fig. 7)
1.
2.
3.
4.
5.
6.
7.
Clean gearmotor boss, output shaft and shaft well.
Install drain pan and evaporator mounting base.
Fill gearmotor shaft well with food-grade grease (Fig. 8).
Install condensate shield and seat against gearmotor boss.
Install mounting base O ring in groove in evaporator mounting base.
Lower bottom bearing assembly into evaporator mounting base.
While maintaining a downward pressure on bottom bearing assembly,
tighten hex head bolt with a 5/16 wrench.
8. Position evaporator over lower bearing assembly and align grooves
with pins in bearing assembly.
9. Install vee band clamp and nut and tighten to 70 in/lb.
10. Place auger in center of evaporator and rotate to mate with drive pin.
11. Install ice compression loop, orienting loop as shown in Fig. 7.
Note: No compression nozzle on MFD400 series flake ice machines.
12. Install upper bearing and seal assembly, rotating bearing to slip pin.
into auger slot.
13. Install upper vee band clamp and nut and tighten to 70 in/lb.
14. If evaporator was replaced, reinstall compression nozzle.
Fig. 8
apply
grease
here
1
2
Gearmotor replacement (Fig. 8)
1. Disassemble evaporator as described above.
2. Disconnect the wire connectors.
3. Remove 4 screws holding gearmotor mounting plate to base of ice
machine and lift gearbox and motor clear of ice machine (Fig. 8.1).
4. Remove machine screws holding mounting plate to motor (Fig. 8.2).
5. Install new motor in reverse order.
T400A/W, MCD400A/W, R400A/W, MFD400A/W, D400A/W Ice Machines29
Ice machine troubleshooting
Flashing water LED at any time indicates that water signal to board had been lost for more than one second.
Ten-second delay: There is a 10 second delay in reaction to loss of water (WTR) or bin (B-E) signals. If signals are not
lost for more than 10 seconds, no reaction will occur.
Problem
Indicators
Corrective Action
Ice machine will not
run.
1. No power to unit.
1. Check that unit is plugged in, circuit breakers are on.
2. Open bin level control.
2. Adjust or replace ice level control.
System status:
compressor,
gearmotor, and fan
motor inoperative.
3. Water OK LED (WTR) not on.
3. Check reservoir for water, restore water to unit.
4. 20M or 2ND LED is on indicating that first or
second torque error has occurred.
4. See #6 below.
5. Gear motor locked up (immediate torque error
indicated by LEDs when board is reset).
5. Repair or replace gearmotor.
6. Replace gearmotor start relay.
6. Open coil on gearmotor start relay causing an
immediate torque error.
Compressor will not
run.
1. Condenser coil plugged causing open overload or
high pressure cut-out.
1. Clean condenser coil and replace overload if
necessary.
System status:
gearmotor and fan
motor run.
2. Defective starting capacitor.
2. Replace start capacitor.
3. Defective starting relay.
3. Replace relay.
4. Open motor winding.
4. Ohm out windings and replace compressor if
necessary.
5. No power output from compressor output terminal
on control board.
Unit cycles
intermittently.
5. Check terminal connection and replace control board
if necessary.
1. Float reservoir running dry, sensing probe
signalling for system to shut down.
1. Check water supply to float and float operation. PC
board will have flashing WTR LED.
Low ice production.
1. Dirty air filter or condenser coil.
1. Clean or replace filter, clean condenser.
Poor quality ice.
2. Restricted air flow to condenser coil.
2. Remove obstruction.
3. Mineral coated evaporator.
3. Clean evaporator.
4. Improper exhaust air provisions.
4. Provide proper exhaust air provisions per Follett
installation manual.
System status:
compressor, gearmotor,
and fan motor cycle.
5. Faulty expansion valve.
6. Low refrigerant charge.
7. Superheat incorrect.
8. Inefficient compressor.
5. Replace expansion valve.
6. Check for leaks; repair, evacuate, and weigh in correct
charge.
7. Check that TXV sensing bulb is securely clamped in
place and not damaged; check that insulated bulb
cover is in place.
8. Replace compressor.
Water leaks
from bottom of
evaporator.
1. O ring seal broken.
1. Replace O ring.
Ice machine runs for
short period of time
and shuts down on
torque error.
1. Kink in ice transport tube.
1. Eliminate kink and check that tube routing complies
with Follett ice machine installation manual.
System status: 20M or
2nd LED is lit.
4. Worn evaporator bearings.
2. Bin level control remains in closed position.
3. Ice transport tube ruptured internally.
5. Faulty gearmotor start relay. Ice machine torques
out within 5 seconds of start-up.
6. Torque out occurs when storage bin fills to capacity.
Evaporator is iced up
on the outside. No ice
production.
System status:
compressor, gearmotor
and fan motor running.
30
1. Gearmotor running but no output rotation.
2. Float reservoir empty.
3. Air bubble in water supply line. Water
in reservoir but not in evaporator.
2. Adjust or replace control.
3. Replace complete length of ice transport tube.
4. Inspect bearings for roughness or binding and replace
if necessary.
5. Replace gearmotor start relay.
6. Ensure that ice contacts bin thermostat before
backing ice up in transport tube. Refer to dispenser
manual for proper thermostat and ice tube mounting.
1. Check for broken gearmotor output shaft or damaged
gearbox.
2. Check for defective water sensor (water OK (WTR)
LED remains on even when float empty or probe
removed from water).
3. Purge air from line.
T400A/W, MCD400A/W, R400A/W, MFD400A/W, D400A/W Ice Machines
Problem
Indicators
Corrective Action
Compressor cycles
intermittently.
1. Compressor start relay in wrong position.
1. Position relay with arrow or word “top”.
2. High pressure cutout open due to high head
pressure.
2. Check discharge pressure and adjust water regulator
valve.
3. Clogged or dirty air filter or condenser coil.
3. Clean or replace filter, clean condenser coil.
4. Improper ventilation.
4. Provide inlet and exhaust air provisions per Follett ice
machine installation manual.
System status:
gearmotor and fan
motor run.
5. Defective compressor.
5. Replace compressor.
Unit runs but not
making ice.
1. Clogged or dirty air filter or condenser coil.
1. Clean or replace filter, clean condenser coil.
2. Compressor not pumping.
2. Replace compressor.
System status:
compressor, gearmotor
& fan motor running.
3. Low refrigerant charge.
3. Check for leaks; repair, evacuate, and weigh in correct
charge.
Compressor and fan
motor will not run.
1. Compressor switch in OFF position.
1. Turn compressor switch on.
2. No output on compressor and fan motor terminals
on control board.
2. Replace control board.
Gearmotor runs.
3. Failed fan motor causes high pressure cut-out to
open.
Intermittent noises from
evaporator.
1. Mineral build-up on evaporator surface.
3. Replace fan motor.
1. Clean evaporator with liquid ice machine cleaner.
T400A/W, MCD400A/W, R400A/W, MFD400A/W, D400A/W Ice Machines31
Replacement parts
Order parts online
www.follettice.com
Evaporator
Reference #
Description
Part #
1
Coupling, vee band, includes nut
502735
2
Bearing assembly, top
502736
3
Loop, ice compression, beveled (see below for Flaker-specific components)
502110
4
Auger (see below for Flaker-specific components)
502737
5
Evaporator (includes insulation jacket, 502740)
502725
6
O ring, bearing housing
500496
7
Bearing assembly, bottom (includes O rings and condensate shield)
502738
8
O ring, mounting base
501063
9
Shield, condensate
500744
10
Screw, Allen 1/4 20 x 1/2 (set of 4)
501080
11
Mounting base, evap. (includes 501063)
502733
12
Bolt, mounting base
502227
13
Gearbox & motor (includes 307192)
502730
Not shown
Mounting base, gearbox
502729
15
Compression nozzle, with single drain
502221
16
Drain pan, evaporator
502727
17
Clamp, compression nozzle and screw
502226
18
Tubing, compression nozzle drain(s) (sold by foot)
500680
Not shown
Grease, Chevron SRI-2, 14 oz
501111
19
Bracket, drain hose
502739
20
Insulation jacket, evaporator
502740
21
Relay, gearmotor
00142042
22
Cover, metal
502744
22
Cover, black plastic
01012228
Flaker-specific components
Reference #
Description
Part #
3
Loop, compression, notched
00124115
4
Auger (with paddle)
00124123
32
T400A/W, MCD400A/W, R400A/W, MFD400A/W, D400A/W Ice Machines
Evaporator
Order parts online
www.follettice.com
2
15
1
17
3
18
4
5
20
19
1
7
6
8
10
11
12
16
9
22
21
13
T400A/W, MCD400A/W, R400A/W, MFD400A/W, D400A/W Ice Machines33
Air-cooled ice machines
Order parts online
www.follettice.com
7
9
6
1
11
16
8
10
13
14
4
2
15
3
12
17
5
34
T400A/W, MCD400A/W, R400A/W, MFD400A/W, D400A/W Ice Machines
Air-cooled ice machines
Order parts online
www.follettice.com
Reference #
Description
Part #
1
Drier
502724
2
Condenser coil, A/C
501187
Not shown
Water sensor
502116
3
Reservoir mounting bracket
501986
4
Float valve & reservoir
500504
5
Drain kit with Agion, evaporator
00141440
6
Evaporator (see page 32 and 33 for complete breakdown)
—
Not shown
Tubing, polypropylene, reservoir supply (sold by foot)
502079
Not shown
Fitting, plastic, float valve (includes sleeve & stem)
502078
Not shown
Compression nozzle, with double drain
502220
Not shown
Compression nozzle, with single drain
502221
7
Valve, expansion, thermal
502726
8
Drain pan, evaporator
502727
9
High pressure cutout
502732
Not shown
Tubing, evaporator drain, 3/4" (19 mm) ID x 1" (26 mm) OD (sold by the foot)
501966
10
Mounting bracket, gearbox
502729
11
Gearbox & motor assembly, 115 V, 60 Hz
502730
12
Tubing, plastic, food grade, 1/2" (13mm) ID (sold by foot)
501191
13
Fan blade
500474
14
Motor, fan, 115 V, 60 Hz
500672
15
Bracket, fan motor
501188
Not shown
Overload, compressor, 115 V, 60 Hz
502782
16
Compressor, 115 V, 60 Hz
502731
17
Base – L400A
502728
Not shown
Strainer, water, threaded connections
500376
Not shown
Strainer, push-in connections
502920
Not shown
Shroud, condenser coil
501820
Not shown
Water inlet & drain assembly, brass
502734
Not shown
Water inlet fitting, plastic
502924
Not shown
Water inlet elbow, plastic
502925
Not shown
Drain fitting, plastic
00109728
Not shown
Jacket, insulation, TXV
502830
Not shown
Bracket, ice tube entry
502698
Not shown
Pinch clamp
00988238
T400A/W, MCD400A/W, R400A/W, MFD400A/W, D400A/W Ice Machines35
Water-cooled ice machines before serial number C57245
Order parts online
www.follettice.com
18
7
16
1
5
9
15
8
14
10
12
13
3
20
4
11
17
6
2
19
36
19
T400A/W, MCD400A/W, R400A/W, MFD400A/W, D400A/W Ice Machines
Water-cooled ice machines before serial number C57245
Order parts online
www.follettice.com
Reference #
Description
Part #
1
Drier
502724
2
Valve, water regulating (includes Iso-washer)
500537
Not shown
Iso-washer (for water regulating valve)
501810
Not shown
Water sensor
502116
3
Float valve & reservoir
500504
4
Reservoir mounting bracket
501986
Not shown
Tubing, polypropylene, reservoir supply (sold by foot)
502079
Not shown
Fitting, plastic, float valve (includes sleeve & stem)
502078
Not shown
Compression nozzle, with double drain
502220
Not shown
Compression nozzle, with single drain
502221
5
Evaporator (see page 32 and 33 for complete breakdown)
—
6
Drain kit with Agion, evaporator
00141440
7
Valve, expansion, thermal
502726
8
Drain pan, evaporator
502727
Not shown
Tubing, evaporator drain, 3/4" (19mm) ID x 1" (26 mm) OD (sold by foot)
501966
9
Gearbox & motor assembly, 115 V, 60 Hz
502730
10
Mounting bracket, gearbox
502729
11
Tubing, plastic, food grade, 1/2" (13 mm) ID (sold by foot)
501191
12
Motor, fan, 115V, 60Hz
500672
13
Bracket, fan motor
501188
14
Fan blade
500790
Not shown
Overload compressor, 115 V, 60 Hz
502782
15
Compressor, 115 V, 60 Hz
502731
16
Coil, condenser
00111898
17
Base, L400W
502741
Not shown
Strainer, water, threaded connections
500376
Not shown
Strainer, push-in connections
502920
Not shown
Water inlet and drain assembly, brass
502734
Not shown
Water inlet fitting, plastic
502924
Not shown
Water inlet elbow, plastic
502925
Not shown
Drain fitting, plastic
00109728
Not shown
Assembly, drain, single fitting
502348
18
High pressure cutout
502732
Not shown
Jacket, insulation, TXV
502830
19
Fitting, condenser drain
00143941
20
Bracket, ice tube entry
502698
Not shown
Pinch clamp
00988238
T400A/W, MCD400A/W, R400A/W, MFD400A/W, D400A/W Ice Machines37
Water-cooled ice machines after serial number C57244
Order parts online
www.follettice.com
15
7
13
1
5
16
12
9
8
10
3
4
11
14
6
2
17
38
17
T400A/W, MCD400A/W, R400A/W, MFD400A/W, D400A/W Ice Machines
Water-cooled ice machines after serial number C57244
Order parts online
www.follettice.com
Reference #
Description
Part #
1
Drier
502724
2
Valve, water regulating (includes Iso-washer)
500537
Not shown
Iso-washer (for water regulating valve)
501810
Not shown
Water sensor
502116
3
Float valve & reservoir
500504
4
Reservoir mounting bracket
501986
Not shown
Tubing, polypropylene, reservoir supply (sold by foot)
502079
Not shown
Fitting, plastic, float valve (includes sleeve & stem)
502078
Not shown
Compression nozzle, with double drain
502220
Not shown
Compression nozzle, with single drain
502221
5
Evaporator (see page 32 and 33 for complete breakdown)
—
6
Drain kit with Agion, evaporator
00141440
7
Valve, expansion, thermal
502726
8
Drain pan, evaporator
502727
Not shown
Tubing, evaporator drain, 3/4" (19 mm) ID x 1" (26 mm) OD (sold by foot)
501966
9
Gearbox & motor assembly, 115 V, 60 Hz
502730
10
Mounting bracket, gearbox
502729
11
Tubing, plastic, food grade, 1/2" (13mm) ID (sold by foot)
501191
Not shown
Overload compressor, 115 V, 60 Hz
502782
12
Compressor, 115 V, 60 Hz
502731
13
Coil, condenser
00195933
14
Base, L400W
502741
Not shown
Strainer, water, threaded connections
500376
Not shown
Strainer, push-in connections
502920
Not shown
Water inlet and drain assembly, brass
502734
Not shown
Water inlet fitting, plastic
502924
Not shown
Water inlet elbow, plastic
502925
Not shown
Drain fitting, plastic
00109728
Not shown
Assembly, drain, single fitting
502348
15
High pressure cutout
502732
Not shown
Jacket, insulation, TXV
502830
16
Ty-rap (2 required)
204584
17
Fitting, condenser drain
00143941
Not shown
Bracket, ice tube entry
502698
Not shown
Pinch clamp
00988238
T400A/W, MCD400A/W, R400A/W, MFD400A/W, D400A/W Ice Machines39
Electrical components
1
2
Order parts online
www.follettice.com
EARTH
L1
L1
L2
L2
L2
L2
L2
POWER
3
RESET
I.D.
LABEL
4
WATER
PROBE
DR
C
20M
60M
2ND
WTR
B-T
B-E
SOFTWARE
I.D.
COMP.
SWITCH
LINE
VAC
FAN
DRIVE
COMM.
24
VAC
COMP.
5
Reference #
Description
Part #
1
Capacitor, start, compressor, 115 V, 60 Hz
502780
2
Relay start, compressor, 115 V, 60 Hz
501588
3
Board, control circuit, 115 V, 60 Hz
502331
Not shown
Water sensor
502116
4
Switch, on/off, compressor
502392
Not shown
Bin thermostat (MCD400A/WBT, MCD400A/WHT, MFD400A/WBT and
MFD400A/WHT only)
500514
5
Board, stand off control (4 required)
501959
40
T400A/W, MCD400A/W, R400A/W, MFD400A/W, D400A/W Ice Machines
Order parts online
www.follettice.com
Ice machine cleaner/descaler
00132001
SafeCLEAN environmentally-friendly cleaner, carton of 24 x 7 oz packets
Ice machine sanitizer
00979674
Nu-Calgon IMS-II Sanitizer, 16 oz. bottle
Miscellaneous
Part #
Description
501860
Condensate pump
502775
Oil, gearmotor, 1 pint
501111
Grease, Mobile FM 222, 14 oz tube
500377
Clamp, ice tube
501921
Grommet, ice tube
502783
Duct – 2" (51mm)
502781
Gasket, air duct
501425
Grille
501986
Bracket, float mounting
501759
Cord and plug (female), dispenser bin signal (F1105A/W)
501858
Cord and plug (female), dispenser power (all 25, 50, 110 series dispensers)
501786
Cord and plug (female), dispenser bin signal (all 25 and 50 series top mount and freestanding dispensers)
501702
Control board adapter (R404A to R12)
502051
Cord and twist-lock plug (male), ice machine bin signal
502052
Cord and twist-lock plug (male), ice machine power
502333
Plug, twist-lock, two lead, male
502334
Plug, twist-lock, two lead, female
502235
Plug, twist-lock, three lead, male
502336
Plug, twist-lock, three lead, female
502794
Panel, right hand, louvered, R400A, MCD400A/W
502795
Cover, top, R400A/W, MCD400A/W
502796
Panel, front utility, R400A, MCD400A
502797
Panel, top front, R400A,MCD400A
502798
Panel, left hand & rear, R400A/W, MCD400A/W
502799
Panel, front, R400W, MCD400W
502800
Filler, base, R400A/W, MCD400A/W
502801
Condenser, L400W
502802
Power cord, R400, MCD400
502803
Bin signal cord, R400, MCD400
502874
Grille, condenser, T400A and MCD400AHT
502875
Filter, air, T400A and MCD400AHT
00918045
Assembly, front cover
T400A/W, MCD400A/W, R400A/W, MFD400A/W, D400A/W Ice Machines41
Order parts online
www.follettice.com
Water treatment accessories for Symphony ice and water dispensers
Reference #
Description
Part #
Standard capacity filter system
Not shown
Follett QC4-FL4S water filter system (includes FL4S primary cartridge and head, coarse
pre-filter and head, pressure gauge, flushing valve; assembled and installed on mounting
bracket), one per ice machine
00130229
Not shown
Follett FL4S primary replacement cartridge
00130245
Not shown
Water filter cartridge – primary, carton of 6
00954297
Not shown
Everpure coarse pre-filter cartridge
00130211
Not shown
Water pre-filter cartridge – pre-filter, carton of 12
00954305
High capacity filter system
Not shown
High capacity water filter system (one per ice machine)
00978957
Not shown
High capacity water filter cartridge – primary, single
00978965
Not shown
High capacity water filter cartridge – primary, carton of 6
00978973
Not shown
Water pre-filter cartridge – pre-filter, single
00130211
Not shown
Water pre-filter cartridge – pre-filter, carton of 12
00954305
Carbonless high capacity filter system
Not shown
Carbonless high capacity water filter system (one per ice machine) – Horizon and Maestro
series ice machines
01050442
Not shown
Carbonless high capacity water filter cartridge – primary, single
01050426
Not shown
Carbonless high capacity water filter cartridge – primary, carton of 6
01050434
Not shown
Water pre-filter cartridge – pre-filter, single
00130211
Not shown
Water pre-filter cartridge – pre-filter, carton of 12
00954305
Not shown
Claris hardness removal filtration system
00986059
Not shown
Replacement filter for Claris system
00985127
Not shown
Reverse osmosis system, 200 gallons per day
00986034
Not shown
Replacement reverse osmosis cartridge
00985085
Not shown
Replacement reverse osmosis pre-filter
00985077
Not shown
Cleaning plug for reverse osmosis system
00985119
Not shown
Cleaning cartridge for reverse osmosis system
00985101
Water pressure regulator (25 psi)
501781
Other filtration
Water pressure
Not shown
42
T400A/W, MCD400A/W, R400A/W, MFD400A/W, D400A/W Ice Machines
Replacement ice machine ordering matrix
Dispenser models
Order parts online
www.follettice.com
Replacement
ice machine model
Dispensers with top mounted ice machines
50CT400A & 50HT400A
D400A
50HT400W & 50HT400W
D400W
25CT 400A & 25HT400A
D400A
25CT400W & 25HT400W
D400W
110CT400AD400A
110CT400WD400W
Dispensers with remote ice machines
25CR400A & 25HR400A
R400A
25CR400W & 25HR400W
R400W
50CR400A & 50HR400A
R400A
50CR400W & 50HR400W
R400W
110CR400AR400A
110CR400WR400W
All U150/VU155 series with air-cooled ice machines
MCD400A
All U150/VU155 series with water-cooled ice machines
MCD400W
All VU300 series with air-cooled ice machines
MCD400A
All VU300 series with water-cooled ice machines
MCD400W
Dispenser models
Replacement
ice machine model
Freestanding dispensers with ice machines in the base
25FB400AD400A
25FB400WD400W
50FB400AD400A
50FB400WD400W
110FB400AD400A
110FB400WD400W
Nugget ice machine on top of bin
MCD400ABTMCD400ABT
MCD400WBTMCD400WBT
Flake ice machine on top of bin
MFD400ABTMFD400ABT
MFD400WBTMFD400WBT
T400A/W, MCD400A/W, R400A/W, MFD400A/W, D400A/W Ice Machines43
Harmony, SafeCLEAN, Symphony and Vision are trademarks of Follett Corporation.
Chewblet, RIDE and Follett are registered trademarks, and Horizon is a trademark of Follett Corporation, registered in US.
801 Church Lane • Easton, PA 18040, USA
Toll free (877) 612-5086 • +1 (610) 252-7301
www.follettice.com
208600R22
© Follett Corporation 2/14
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising